Photo Modules for PCM Remote Control Systems Available types for different carrier frequencies Type fo Type fo TSOP283 3 khz TSOP2833 33 khz TSOP2836 36 khz TSOP2837 36.7 khz TSOP2838 38 khz TSOP284 4 khz TSOP2856 56 khz Description The TSOP28.. series are miniaturized receivers for infrared remote control systems. PIN diode and preamplifier are assembled on lead frame, the epoxy package is designed as IR filter. The demodulated output signal can directly be decoded by a microprocessor. The main benefit is the reliable function even in disturbed ambient and the protection against uncontrolled output pulses. 14 5 Features Photo detector and preamplifier in one package Internal filter for PCM frequency TTL and CMOS compatibility Output active low Improved shielding against electrical field disturbance Suitable burst length 6 cycles/burst Special Features Small size package Enhanced immunity against all kinds of disturbance light No occurrence of disturbance pulses at the output Short settling time after power on (<2s) Block Diagram PIN Input AGC Control Circuit Band Pass Demodulator 3 k 2 1 3 V S OUT GND 14318 Document Number 8258 www.vishay.de FaxBack +1-48-97-56 1 (7)
Absolute Maximum Ratings T amb = 25 C Parameter Test Conditions Symbol Value Unit Supply Voltage (Pin 2) V S.3...6. V Supply Current (Pin 2) I S 5 ma Output Voltage (Pin 1) V O.3...6. V Output Current (Pin 1) I O 5 ma Junction Temperature T j 1 C Storage Temperature Range T stg 25...+85 C Operating Temperature Range T amb 25...+85 C Power Consumption (T amb 85 C) P tot 5 mw Soldering Temperature t 1 s, 1 mm from case T sd 26 C Basic Characteristics T amb = 25 C Parameter Test Conditions Symbol Min Typ Max Unit Supply Current (Pin 2) V S = 5 V, E v = I SD.9 1.5 ma V S = 5 V, E v = 4 klx, sunlight I SH 1.3 ma Supply Voltage (Pin 2) V S 4.5 5.5 V Transmission Distance E v =, test signal see fig.6, d 35 m IR diode TSAL62, I F = 3 ma Output Voltage Low (Pin 1) I OL =.5 ma,e e =.7 mw/m 2, V OL 25 mv f = f o Irradiance (3 4 khz) Pulse width tolerance: E e min.3.5 mw/m 2 Irradiance (56 khz) t pi 4/f o <t po <t pi + 6/f o, test signal see fig.6 E e min.7 mw/m 2 Irradiance E e max 3 W/m 2 Directivity Angle of half transmission distance ϕ 1/2 ±45 deg Application Circuit 1 *) +5V TSAL62.. TSOP28.. 2 1 4.7 F *) >1 k optional C 14319 3 GND *) recommended to suppress power supply disturbances www.vishay.de FaxBack +1-48-97-56 Document Number 8258 2 (7)
Suitable Data Format The circuit of the TSOP28... is designed in that way that unexpected output pulses due to noise or disturbance signals are avoided. A bandpassfilter, an integrator stage and an automatic gain control are used to suppress such disturbances. The distinguishing mark between data signal ( not suppressed) and disturbance signal (supressed) are carrier frequency, burst length and Signal Gap Time (see diagram below). The data signal should fullfill the following condition: Carrier frequency should be close to center frequency of the bandpass (e.g. 38kHz). Burst length should be 6 cycles/burst or longer. After each burst a gap time of at least 1 cycles is neccessary. The data format should not make a continuous signal transmission. There must be a Signal Gap Time (longer than 15ms) at least each 9ms (see Figure A). Some examples for suitable data format are: NEC Code (repetitive pulse), NEC Code (repetitive data), Toshiba Micom Format, Sharp Code, RC5 Code, RECS 8 Code, R 2 Code. When a disturbance signal is applied to the TSOP28... it can still receive the data signal. However the sensitivity is reduced to that level that no unexpected pulses will occure. Some examples for such disturbance signals which are suppressed by the TSOP28... are: DC light (e.g. from tungsten bulb or sunlight), Continuous signal at 38kHz or at any other frequency, Signals from fluorescent lamps (see Figure B). Continuous IR signal (e.g. 1ms burst, 2ms pause) Signal Gap Time 1 2 3 4 5 6 7 8 9 1 time [ms] Figure A: Data Signal (Output of IR Receiver) with a Signal Gap Time of 2ms Signal Gap Time 2 4 6 8 1 12 14 16 18 2 time [ms] Figure B: Disturbance Signal from Fluorescent Lamp with Signal Gap Time of 7ms (suppressed by TSOP28..) Document Number 8258 www.vishay.de FaxBack +1-48-97-56 3 (7)
Typical Characteristics (T amb = 25 C unless otherwise specified) e E min / e E Rel. Responsitivity 94 912.2 f = f 5% f ( 3 db ) = f /7..7.9 1.1 f/f Relative Frequency 1.3 96 12215 1. 1. f = f o 1 khz 1 khz 1 Hz.1.1 1. 1. 1. V srms AC Voltage on DC Supply Voltage (mv) Figure 1. Frequency Dependence of Responsivity Figure 4. Sensitivity vs. Supply Voltage Disturbances 1431 4.5 4. 3.5 3. 2.5 2. 1.5.5 Correlation with ambient light sources ( Disturbance effect ) : 1 W/m2 1.4 klx ( Stand.illum.A, T = 2855 K ) 8.2 klx ( Daylight, T = 59 K ) Ambient, = 95 nm.1.1 1. 1. E DC Irradiance (W/m 2 ) 14312.9 Sensitivity in dark ambient.7.5.3.2.1 4.5 4.6 4.7 4.8 4.9 5. 5.1 5.2 5.3 5.4 5.5 V S Supply Voltage ( V ) Figure 2. Sensitivity in Bright Ambient Figure 5. Sensitivity vs. Supply Voltage E e min Threshold Irradiance ( mw/m ) 2 94 8147 2. 1.6 f(e)=f.. 1.6 E Field Strength of Disturbance ( kv / m ) Figure 3. Sensitivity vs. Electric Field Disturbances 2. E e Optical Test Signal 6 s 6 s t T D * T rep =1 ms * T rep T D > 15 ms is recommended for optimal function V O V OH V OL Output Signal, ( see Fig.7 ) 1588 T on T off t Figure 6. Output Function www.vishay.de FaxBack +1-48-97-56 Document Number 8258 4 (7)
T on,t off Output Pulse Length (ms) 16163.75.7 5.55.5 5 T off T on optical test signal, fig.6.1 1. 1. 1. 1.1. E e Irradiance (mw/m 2 ) Figure 7. Output Pulse Diagram I Supply Current ( ma ) s 14317 1.7 1.6 Supply current in dark ambient 1.5 1.4 1.3 1.1.9.7.5 4.5 4.6 4.7 4.8 4.9 5. 5.1 5.2 5.3 5.4 5.5 V S Supply Voltage ( V ) Figure 1. Supply Current vs. Supply Voltage I Supply Current ( ma ) s 14315 2. 1.8 1.6 V s = 5 V 1.4.2 3 15 15 3 45 6 75 9 T amb Ambient Temperature ( C ) S ( ) rel Relative Spectral Sensitivity 94 848.2 75 85 95 15 Wavelength ( nm ) 115 Figure 8. Supply Current vs. Ambient Temperature Figure 11. Relative Spectral Sensitivity vs. Wavelength 96 12221.9.7.5.3.2.1 Sensitivity in dark ambient 3 15 15 3 45 6 75 9 T amb Ambient Temperature ( C ).9.7 96 12223p2 1 2.2.2 d rel Relative Transmission Distance 3 4 5 6 7 8 Figure 9. Sensitivity vs. Ambient Temperature Figure 12. Directivity Document Number 8258 www.vishay.de FaxBack +1-48-97-56 5 (7)
Dimensions in mm 13655 www.vishay.de FaxBack +1-48-97-56 Document Number 8258 6 (7)
Ozone Depleting Substances Policy Statement It is the policy of Vishay Semiconductor GmbH to 1. Meet all present and future national and international statutory requirements. 2. Regularly and continuously improve the performance of our products, processes, distribution and operating systems with respect to their impact on the health and safety of our employees and the public, as well as their impact on the environment. It is particular concern to control or eliminate releases of those substances into the atmosphere which are known as ozone depleting substances ( ODSs). The Montreal Protocol (1987) and its London Amendments (199) intend to severely restrict the use of ODSs and forbid their use within the next ten years. Various national and international initiatives are pressing for an earlier ban on these substances. Vishay Semiconductor GmbH has been able to use its policy of continuous improvements to eliminate the use of ODSs listed in the following documents. 1. Annex A, B and list of transitional substances of the Montreal Protocol and the London Amendments respectively 2. Class I and II ozone depleting substances in the Clean Air Act Amendments of 199 by the Environmental Protection Agency (EPA) in the USA 3. Council Decision 88/54/EEC and 91/69/EEC Annex A, B and C ( transitional substances) respectively. Vishay Semiconductor GmbH can certify that our semiconductors are not manufactured with ozone depleting substances and do not contain such substances. We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications. All operating parameters must be validated for each customer application by the customer. Should the buyer use Vishay-Telefunken products for any unintended or unauthorized application, the buyer shall indemnify Vishay-Telefunken against all claims, costs, damages, and expenses, arising out of, directly or indirectly, any claim of personal damage, injury or death associated with such unintended or unauthorized use. Vishay Semiconductor GmbH, P.O.B. 3535, D-7425 Heilbronn, Germany Telephone: 49 ()7131 67 2831, Fax number: 49 ()7131 67 2423 Document Number 8258 www.vishay.de FaxBack +1-48-97-56 7 (7)