Installation and Assembly:

Transcription

1 Installation and Assembly: PeerSound Wireless Short Throw Projector AV System PeerSound Wireless Short Throw Projector Audio System Models: WL-AU-PST600(A), WL-AU-PST1200(A), WL-AU-PST1600(A), WL-AU-PST600(A)-W, WL-AU-PST1200(A)-W, WL-AU-PST1600(A)-W Max Load Capacity: 25 lb (11.3 kg) 2300 White Oak Circle Aurora, Il (800) Fax: (800) ISSUED: SHEET #:

2 NOTE: Read entire instruction sheet before you start installation and assembly. Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US customers please call Peerless customer care at , for all international customers, please contact your local distributor. This product should only be installed by someone of good mechanical aptitude, has experience with basic building construction, and fully understands these instructions. Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. Never exceed the Maximum UL Load Capacity. See page one. If mounting to wood joists ceilings, make sure that mounting screws are anchored into the center of the studs. Use of an "edge to edge" stud fi nder is highly recommended. Always use an assistant or mechanical lifting equipment to safely lift and position equipment. Tighten screws fi rmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding power. This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury. This product was designed to be installed on the following wall construction only; WALL CONSTRUCTION Wood Stud Wood Joist Solid Concrete Metal Stud Brick Other or unsure? Tools Needed for Assembly stud fi nder ("edge to edge" stud fi nder is recommended) phillips screwdriver drill 3/8" bit for solid concrete surface 3/16" bit for wood studs 1/2" bit for metal studs socket wrench 7/16" socket level hammer Pencil Tape Measure Table of Contents WARNING HARDWARE REQUIRED Included Included Included Included (Not Evaluated By UL) Contact Qualifi ed Professional (Not Evaluated By UL) Contact Qualifi ed Professional Parts List... 3 Projector Positioning... 8 Installation to Double Stud Wall Installation to Metal Stud Wall Installation to Solid Concrete or Cinder Block...14 Attaching Adapter Plate to Projector...22 Component Connections...25 Projector Alignment...26 Projector Arm Adjustment...28 Amplifi er ISSUED: SHEET #:

3 Parts List WL-AU-PST600 WL-AU-PST600-W WL-AU-PST1200 WL-AU-PST1200-W WL-AU-PST1600 WL-AU-PST1600-W Description Qty. Part # Part # Part # Part # Part # Part # AA wireless transmitter hds BB wireless reciever hds CC power adapter - 12v 2a DD plastic stand for hds EE vga to rca adapter for hds FF remote controller for hds GG battery cr2025 3v HH ir flasher II ir-extender gen JJ amplifier, 25x2-2 input KK amp kit 50w ac to dc power adapter 24v-2a LL amp kit 50w ir extender eye, oval with tape MM amp kit 50w card remote with battery NN 3.5 audio cable OO hdmi cable 1 EC-HD06F EC-HD06F EC-HD12F EC-HD12F EC-HD12F EC-HD12F Parts List WL-AU-PST600A WL-AU-PST600A-W WL-AU-PST1200A WL-AU-PST1200A-W WL-AU-PST1600A WL-AU-PST1600A-W Description Qty. Part # Part # Part # Part # Part # Part # AA wireless transmitter hds-200 BB wireless reciever hds-200 CC power adapter - 12v 2a DD plastic stand for hds-200 EE vga to rca adapter for hds-200 FF remote controller for hds-200 GG battery cr2025 3v HH ir flasher II ir-extender gen-2 JJ amplifier, 25x2-2 input KK amp kit 50w ac to dc power adapter 24v-2a LL amp kit 50w ir extender eye, oval with tape MM amp kit 50w card remote with battery NN 3.5 audio cable OO hdmi cable 1 EC-HD06F EC-HD06F EC-HD12F EC-HD12F EC-HD12F EC-HD12F 3 ISSUED: SHEET #:

4 AA BB CC DD EE FF GG HH II JJ KK LL MM NN OO AUDIO-REMOTE NOTE: Depending on model number, some parts may not be required. 4 ISSUED: SHEET #:

5 Before beginning, make sure you have all parts shown below. Parts List WL-AU-PST600 WL-AU-PST600-W WL-AU-PST1200 WL-AU-PST1200-W WL-AU-PST1600 WL-AU-PST1600-W Description Qty. Part # Part # Part # Part # Part # Part # A enclosure assembly B projector arm C end cap D projector mount assembly E adapter plate F 10mm concrete anchor G 5/16" x 3" wood screw H power strip I receiver bracket assembly J amp bracket K mic bracket L cover assembly M cover plate assembly N cable bushing O finishing cap P cable tie anchor Q cable tie R 4mm security allen wrench S toggler T 1/4"-20 x 2.5 phillips screw U m5 x 6mm serrated washer head security screw V m8 x 15mm security screw W m4 x 10mm serrated washer head security screw X m5 x 6mm security screw Y 3mm allen wrench ISSUED: SHEET #:

6 Parts List WL-AU-PST600A WL-AU-PST600A-W WL-AU-PST1200A WL-AU-PST1200A-W WL-AU-PST1600A WL-AU-PST1600A-W Description Qty. Part # Part # Part # Part # Part # Part # A enclosure assembly B projector arm C end cap D projector mount assembly E adapter plate F 10mm concrete anchor G 5/16" x 3" wood screw H power strip I receiver bracket assembly J amp bracket K mic bracket L cover assembly M cover plate assembly N cable bushing O finishing cap P cable tie anchor Q cable tie R 4mm security allen wrench S toggler T 1/4"-20 x 2.5 phillips screw U m5 x 6mm serrated washer head security screw V m8 x 15mm security screw W m4 x 10mm serrated washer head security screw X m5 x 6mm security screw Y 3mm allen wrench ISSUED: SHEET #:

7 O A B C D E K G F J L I H N M R S Q P W U V X T Y NOTE: Depending on model number, some parts may not be required. 7 ISSUED: SHEET #:

8 Projector Positioning 1 Ensure the correct model is selected. Utilize both the projector manual and the Peerless Projector throw distance calculator ( projector_throw_distance_calculator) to obtain the following information: A B C D E F Projector Make Projector Model Image size, resultant image height Horizontal distance required from lens to screen Distance above or below top of screen/image to lens center Lens center to top of projector Left or Right lens offset from center of projector mounting pattern Use the information above combined with the following illustrations to locate the enclosure on the wall. Once located, use the installation template to drill holes and continue installation. C L ENCLOSURE 8" 10" 12" 23.5" F C L SCREEN 8 ISSUED: SHEET #:

9 1.5" MIN. WL-AU-PST600 = 18.04" " WL-AU-PST1200 = 31.03" " WL-AU-PST1600 = 46.78" " CEILING C L 9.5" 1.5" + D + E 1.5" MIN. SCREEN HEIGHT D B IMAGE HEIGHT C E * - IMAGE BORDER TO SCREEN DETERMINED BY INSTALLER. The enclosure has an internal cut out allowing for the pre-installation of a single or dual gang power outlet. This outlet then is exposed inside the enclosure, yet hidden once the cover is installed. See below for location of this window. 8.63" 7.50" 7.38" ISSUED: SHEET #:

10 Skip to page 11 for Metal Stud Installation Skip to page 13 for Solid Concrete or Cinder Block Installation. Installation to Double-Stud Wall WARNING Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. Tighten wood screws so that wall plate is fi rmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. Never tighten in excess of 80 in. lb (9 N.M.). Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud fi nder is highly recommended. Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Installers are responsible to provide hardware for other types of mounting situations (not evaluated by UL). 2 Use a stud fi nder to locate the edges of the studs and draw a vertical line down the center of each stud. Place wall plate template on wall. Level wall plate template and mark center of four mounting holes making sure that the mounting holes are on the stud centerlines. Drill four 3/16" (5mm) dia. pilot holes to a depth of 3" (76 mm). Insert two screws (G), leaving a 1/2" gap between the screw head and the wall, as shown in fi g G 1/2" (13mm) fig ISSUED: SHEET #:

11 2 Using the keyholes in the back of enclosure assembly (A), place enclosure assembly (A) on to the two screws (G). Slide enclosure assembly (A) over until the mark on the wall plate lines up with the center of the screw (G) as shown in detail A. NOTE: When mounting on 16" stud centers, use bottom set of slots. For 20" and 24" stud centers, use top set of slots. A G fig. 2.2 KEYHOLE DETAIL A 2 Position enclosure on wall. Install remaining 2 screws (G). Level enclosure assembly (A) and tighten all screws. A G fig ISSUED: SHEET #:

12 Installation to Metal Stud Wall WARNING Drywall must be 1/2" or thicker, and metal stud must be 24 gauge or heavier. Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components (Not Evaluated By UL). 2 Use a stud fi nder to locate the edges of the studs and draw a vertical line down the center of each stud. Place wall plate template on wall. Level wall plate template and mark center of four mounting holes making sure that the mounting holes are on the stud centerlines. Drill four 1/2" (13mm) dia. holes through drywall and metal studs. NOTE: It may be necessary to drill 5/32" pilot holes prior to drilling 1/2" holes. Insert togglers (S) as shown in figure 2.4. Insert two 1/4"- 20 x 2.5" phillips screws (T), leaving a 1/2" gap between the screw head and the wall, as shown in fi g WARNING Product must be mounted through drywall that has a minimum thickness of 1/2" and into metal studs, 24 gauge or heavier. Make sure that togglers are anchored into the center of the studs as shown in fi gure 2.2. The use of an "edge to edge" stud fi nder is highly recommended. This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury. fig S Pivot end of toggler (S). 2 Push into hole. 3 T Rotate toggler (S) clockwise to wedge it against inside walls of metal stud. 4 fig. 2.5 Slide plastic cap forward while pulling back fi rmly on ring. 5 1/2" (13mm) Break off excess. 12 ISSUED: SHEET #:

13 2 Using the keyholes in the back of enclosure assembly (A), place enclosure assembly (A) on to the two 1/4"20 x 2.5" phillips screws (T) as shown in fig Slide enclosure assembly (A) over until the mark on the wall plate lines up with the center of the 1/4"20 x 2.5" phillips screws (T) as shown in detail B. NOTE: When mounting on 16" stud centers, use bottom set of slots. For 20" and 24" stud centers, use top set of slots. fig. 2.6 A T KEYHOLE DETAIL B 2 Position enclosure on wall. Install remaining two 1/4"20 x 2.5" phillips screws (T). Level enclosure assembly (A) and tighten all screws. A G fig ISSUED: SHEET #:

14 Installation to Solid Concrete or Cinder Block WARNING When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" (35 mm) of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" (25 mm) minimum from the side of the block. Cinder block must meet ASTM C-90 specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity. Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor. Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. 2 Place wall plate template on wall. Level template on wall and mark center of four mounting holes. Drill four 3/8" (10 mm) dia. pilot holes to a depth of 3" (76 mm). Insert anchors (F) into holes fl ush with wall as shown (right). Insert two screws (G), leaving a 1/2" gap between the screw head and the wall, as shown in fi g WARNING Tighten screws so that wall plate is fi rmly attached, but do not overtighten. Overtightening can damage screws, greatly reducing their holding power. Never tighten in excess of 80 in. lb (9 N.M.). Always attach concrete expansion anchors directly to load-bearing concrete. Never attach concrete expansion anchors to concrete covered with plaster, drywall, or other fi nishing material. If mounting to concrete surfaces covered with a fi nishing surface is unavoidable (not evaluated by UL), the fi nishing surface must be counterbored as shown below. Be sure concrete anchors do not pull away from concrete when tightening screws. If plaster/drywall is thicker than 5/8" (16 mm), custom fasteners must be supplied by installer (not evaluated by UL). 1 Drill holes and insert anchors (F). 2 Place enclosure (A) over anchors (F) and secure with screws (G). 3 Tighten all fasteners. G G A concrete surface F F INCORRECT CORRECT 1/2" (13mm) CUTAWAY VIEW wall plate plaster/ dry wall concrete wall plate plaster/ dry wall concrete fig ISSUED: SHEET #:

15 2 Using the keyholes in the back of enclosure assembly (A), place enclosure assembly (A) on to the two screws (G). Slide enclosure assembly (A) over until the mark on the wall plate lines up with the center of the screw (G) as shown in detail C. NOTE: When mounting on 16" stud centers, use bottom set of slots. For 20" and 24" stud centers, use top set of slots. fig. 2.9 A G KEYHOLE DETAIL C 2 Position enclosure on wall. Install remaining 2 screws (G). Level enclosure assembly (A) and tighten all screws. A fig G 15 ISSUED: SHEET #:

16 3 Route cables through projector arm (B) as shown. Note: Cable representation is generic. B 4 Install end cap (C) onto projector arm (B). Rotate mount (D) at least three full turns onto the end of projector arm (B). B C D 16 ISSUED: SHEET #:

17 5 Hook tilt plate on projector arm (B) onto mounting bracket inside of enclosure (A). A B TILT PLATE 6 Install two M8 x 15mm screws (V), approximately 4 turns, into tilt plate as shown. Do not tighten screws. V 17 ISSUED: SHEET #:

18 6 Install power strip (H) onto mounting screws inside of enclosure (A). A H 7 If your power source is located outside of the enclosure (A), route the power cord from the power strip through the hole in the top or bottom of enclosure (A). Push the power cord through the bottom of the cable bushing (N). Push cable bushing (N) into hole in the enclosure (A). Plug into power source. If your power source is located inside the enclosure, push fi nishing cap (O) into top and bottom holes in the enclosure (A). A O N A 18 ISSUED: SHEET #:

19 Continue to step 7 for WL-AU-PST600(-W), WL-AU-PST1200(-W), WL-AU-PST1600(-W) Models. Skip to step 8 for WL-AU-PST600A(-W), WL-AU-PST1200A(-W), WL-AU-PST1600A(-W) Models. 7 Slide the receiver mounting bracket (I) over the HDS200 receiver (BB) as shown. Install HDS200 receiver assembly into enclosure (A) using two M5 x 6mm screws (U). Hint: The Receiver has only 1 HDMI port and is marked RECEIVER on the back of the unit. U I BB A 8 Install amp brackets (J) into enclosure (A) using 2 M5 x 6mm screws (U). U J A 19 ISSUED: SHEET #:

20 9 Install amp between amp brackets (J) and secure using two M4 x 10mm screws (W) as shown. W JJ J 10 OPTIONAL. Install wireless mic receiver (not included) into area provided. 20 ISSUED: SHEET #:

21 OPTIONAL. Secure mic receiver using mic bracket (K) and two M5 x 6mm screws (U). 11 U K 12 Install IR extenders to bottom of enclosure assembly (A) as shown. NOTE: Place double sided tape included with IR extender (LL) to bottom of IR extender fi rst, then install to bottom of enclosure assembly (A). Hint: IR extender mounting location may be moved, within cable limits, so that a close located projector does not block IR signal. II LL A DOUBLE SIDED TAPE NOTE: IR extender (II) is used on WL-AU-PST600(-W), WL-AU-PST1200(-W) and WL-AU-PST1600(-W) models only. 21 ISSUED: SHEET #:

22 Route connector ends of IR extenders through holes in bottom of enclosure assembly (A) as 13 shown. A Attaching Adapter Plate to Projector 14 NOTE: The projector you are installing may differ in appearance from the sample illustrated below. Place projector upside down. Locate adapter plate (E) with notch facing forward as close to projector center of gravity as possible without covering any mounting holes. Loosen channels with 4mm security allen wrench (R), and if there are only three mounting holes remove fourth channel. Using one channel for each mounting hole, position feet of channels over mounting holes as shown below. IMPORTANT: If projector does not have at least three mounting holes, do not use this adapter plate. NOTE: Some projectors have feet which can be removed and the corresponding threaded insert can be used for a mounting hole. NOTE: Once channels are in position retighten fasteners. *Notch indicates front of projector. MOUNTING HOLE CHANNEL FOOT OF CHANNEL B * GENERIC PROJECTOR 22 ISSUED: SHEET #:

23 15 Attach adapter plate (E) to projector using one screw from baffeled fastener pack (included with projector mount) for each channel as shown below. Tighten all screws, while keeping the center of gravity. Be sure that adapter plate (E) is straight. Adjust the feet of the channels to keep the adapter plate level. Tighten all screws with 4mm security allen wrench (R) while keeping the center of gravity. If M3 screws are used, tighten using 2mm security allen wrench (included with projector mount). NOTE: Projectors will require different size screws for mounting. Use a combination of screws and foot adjustment that will result in channels of adapter plate (E) fitting tightly against projector. IMPORTANT: In order to properly engage the threads in the mounting holes, the screw must be turned at least 3 full turns. NOTE: If using M3 screws, place washer from baffeled fastener pack (included with projector mount) between screw and foot of channel. CAUTION It is the responsibility of the installer to ensure that the projector is properly ventilated. Feet of channels are used to raise the mount off the projector surface. PROJECTOR MOUNT SCREWS E FOOT OF CHANNEL 23 ISSUED: SHEET #:

24 WARNING Always use an assistant or mechanical lifting equipment to safely lift and position the projector. Slide connection block with projector into projector mount assembly (D) as shown. Push in and 16 tighten captive screw to secure projector to projector mount assembly (D). Tighten swivel stop screw as shown in fi gure 7.3 using 4mm security allen wrench CONNECTION BLOCK PROJECTOR KNOB SWIVEL STOP SCREW 17 IMPORTANT: For security installations, insert one M5 x 8mm socket pin screw (included with projector mount) through projector mount assembly (D) and into connection block as shown. Tighten screw with 4mm security allen wrench (R). M5 x 8mm SCREW 24 ISSUED: SHEET #:

25 Component Connections 18 Use the following diagram to make the component connections. NOTE: For transmitter setup instructions, refer to the Installation and Operation section of the HDS200 user manual (WL-AU- PST600(-W), WL-AU-PST1200(-W), WL-AU-PST1600(-W) models only). TO MIC RECEIVER (NOT INCLUDED. SEE AUDIO INPUTS) SPEAKERS (PRE-WIRED) AV-OUT OO CC BB IR-IN AUDIO-OUT II COMPONENT-OUT USB LAN H RECEIVER DC NN JJ KK IR IN MIC LL AUX GAIN PROJECTOR NOTE:Component-Out or AV-Out may also be used for projector based upon output resolutions of the source being implemented. (Cables not included) 25 ISSUED: SHEET #: HDMI-OUT

26 19 20 Power on the projector. Use the projector setup screen to complete the steps below. Level projector arm (B). Turn tilt screw clockwise to raise or counter-clockwise to lower. Once level, tighten the four M8 x 15mm screws (V). V B TILT SCREW Projector Alignment To adjust yaw (swivel) : Loosen screw on projector mount assembly (D) indicated below until 21 projector mount can be rotated. Rotate mount to desired position and retighten screw. +/- 10 ENG Loosen, adjust, tighten. ESP Afl oje, ajuste, apriete. FRN Desserrez, réglez, puis serrez. DEU Lösen, einstellen, anziehen. NEL Losdraaien, aanpassen, aandraaien. ITL Allentare, regolare, stringere. ČEŠ Uvolnit, nastavit, přitáhnout. SLK Uvoľniť, nastaviť, pritiahnuť. POR Desaperte, ajuste, aperte. TÜR Gevşetin, ayarlayın, sıkın. SCREW FOR YAW (SWIVEL) STOP 26 ISSUED: SHEET #:

27 22 To adjust pitch (forward and backward tilt): Turn knob on back of mount as shown below. Pull knob out and turn by hand for easy adjustment or insert #2 phillips screwdriver in end of knob and turn. To adjust roll (side to side tilt): Turn knob on side of mount as shown below. Pull knob out and turn by hand for easy adjustment or insert #2 phillips screwdriver in end of knob and turn. ENG Loosen, adjust, tighten. ESP Afl oje, ajuste, apriete. FRN Desserrez, réglez, puis serrez. DEU Lösen, einstellen, anziehen. NEL Losdraaien, aanpassen, aandraaien. ITL Allentare, regolare, stringere. ČEŠ Uvolnit, nastavit, přitáhnout. SLK Uvoľniť, nastaviť, pritiahnuť. POR Desaperte, ajuste, aperte. TÜR Gevşetin, ayarlayın, sıkın. ENG Loosen, adjust, tighten. ESP Afl oje, ajuste, apriete. FRN Desserrez, réglez, puis serrez. DEU Lösen, einstellen, anziehen. NEL Losdraaien, aanpassen, aandraaien. ITL Allentare, regolare, stringere. ČEŠ Uvolnit, nastavit, přitáhnout. SLK Uvoľniť, nastaviť, pritiahnuť. POR Desaperte, ajuste, aperte. TÜR Gevşetin, ayarlayın, sıkın / ISSUED: SHEET #:

28 Projector Arm Adjustment 23 Loosen the arm lock screw on bottom of projector arm (B) using 3mm allen wrench (Y) (for -W models) or (R). Adjust extension of arm to desired position and tighten arm lock screw. B ARM LOCK SCREW 28 ISSUED: SHEET #:

29 Amplifier MIC AMPLIFIER IR IN AUX GAIN AUDIO-REMOTE Main POWER Button (Unit) Turns ON/OFF the unit s main power. If the main power button on the unit is not turned on the unit will not respond to remote control. Note: If the power is turned OFF using the face button while the unit is in stand-by mode, and then turned back on via the push button, the unit will remain in stand-by mode till the remote is used to turn it on. POWER Button (Remote Control) The power button on the remote control allows toggling between STAND-BY mode and power ON mode. In the STAND-BY mode the unit is not fully turned off (the main push button turns the unit off completely and should only be pressed to turn ON the unit during installation). Indicator Light Off When the indicator light is not active the unit is OFF Red When the indicator light is red the unit is in STAND-BY mode. (Main Power Button (On Unit) must be in the ON position) Green When the indicator light is green the unit is turned ON. (Main Power Button (On Unit) must be in the ON position) AUDIO INPUTS Two stereo audio inputs include Auxiliary and Microphone connections. When using the microphone (not included) it is recommended to use a mono to stereo adapter (not included). VOLUME ADJUSTMENT (Unit and Remote Control) Volume adjustment button on the unit or the remote control adjusts volume for the Auxiliary and Microphone input simultaneously. The indicator light for volume adjustment will fl ash during volume adjustment. MODE SWITCH The MODE Switch toggles between the units Stereo and Mono mode. When using the optional Microphone capability with this unit it is recommended to use the MONO mode for best audio results. MIC GAIN ADJUSTMENT The gain adjustment knob on the back of the unit goes from 0 (off) up to +10dB (at signal level) over the Auxiliary input. 29 ISSUED: SHEET #:

30 Amplifier Setup 24 Connect the desired audio sources to the unit. Turn on the amplifi er using the Main Power Button (Note: Remote control function will not work unless the unit Main Power has been turned on). Ensure that the Power Indicator light is solid Green. Adjust volume to desired level. Setup HDS200 transmitter and AV sources. (See HDS200 Quick Start Guide or User Manual 25 for instructions) Once complete, test audio from AV sources. Press the vol+ and vol- arrows on the Amplifi er remote control. If using a PC as the audio source, ensure headphone output is enabled and volume is at least half. For Wireless Microphone setup, continue to step 26 Otherwise, skip to step 27. Wireless Microphone Setup When a wireless microphone system is installed, the relative gain to the HDS200 needs to be set. For fixed level sources (Blu-Ray player): Play source with amplifi er volume at a comfortable level. Adjust mic gain the the back of the amplifi er while talking into the microphone to allow vocals to be slightly louder than the fi xed source volume. Confi rm no feedback or "mic hotness" is present at high amplifi er volumes. Fine tune as necessary. 26 For variable level sources (PC): Set variable source level at 25%. Adjust mic gain the the back of the amplifi er while talking into the microphone to allow vocals to be slightly louder than the variable source volume. If at max mic gain on amplifi er, and the microphone is not loud enough, lower variable source volume and repeat adjustment steps. Confi rm no feedback or "mic hotness" is present at high amplifi er volumes. Fine tune as necessary. 30 ISSUED: SHEET #:

31 27 Attach cover assembly (L). Install seven M5 x 6mm screws (X). Remove protective fi lm from assembly (L) cover. X L PROTECTIVE FILM (REMOVE) 28 Remove protective fi lm from cover plate assembly (M) and position under projector arm (B) as shown. Install one M5 x 6mm screw (X) to secure (optional). NOTE: The area behind the cover plate assembly (M) can provide a secure location to store the remote controls for the HDS200 and amplifi er. B M X 31 ISSUED: SHEET #:

32 Peerless Industries, Inc. ( Peerless-AV ) warrants to original end-users of Peerless-AV products that Peerless-AV products will be free from defects in material and workmanship, under normal use, for the periods listed below, from the date of purchase by the original end-user. At its option, Peerless-AV will repair or replace with new or refurbished products or parts, or refund the purchase price of any Peerless-AV product which fails to conform with this warranty. In no event shall the duration of any implied warranty of merchantability or fitness for a particular purpose be longer than the period of the applicable express warranty set forth above. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty does not cover damage caused by (a) service or repairs by the customer or a person who is not authorized for such service or repairs by Peerless-AV, (b) the failure to utilize proper packing when returning the product, (c) incorrect installation or the failure to follow Peerless-AV s instructions or warnings when installing, using or storing the product, or (d) misuse or accident, in transit or otherwise, including in cases of third-party actions and force majeure. This warranty also does not cover corrosion or rust resulting from damaged, scratched or chipped paint or other surfaces. In no event shall Peerless-AV be liable for incidental or consequential damages or damages arising from the theft of any product, whether or not secured by a security device which may be included with the Peerless-AV product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty is in lieu of all other warranties, express or implied, and is the sole remedy with respect to product defects. No dealer, distributor, installer or other person is authorized to modify or extend this Limited Warranty or impose any obligation on Peerless-AV in connection with the sale of any Peerless-AV product. This warranty gives specific legal rights, and you may also have other rights which vary from state to state. Product Mounts Furniture Cables Cleaning Products Electronic Products and components LIMITED WARRANTY Warranty Period 5 years 1 year 25 years 1 year 1 year Peerless-AV 2300 White Oak Circle Aurora, IL tech@peerlessmounts.com Ph: (800) Fax: (800) , Peerless Industries, Inc.