For Use With Products Manufactured by

Transcription

1 1 EWP PRODUCT GUIDE For Use With Products Manufactured by SKH34R- LSSH179 THF1795 THO17118 Westampton Largo Montgomery Humble Corona Livermore Thornhill, Ontario

2 GENERAL NOTES Follow these instructions to ensure the proper installation of products. 1) See current Product Catalog for General Notes, Warranty, and installation information for hanger models, joist sizes, and header situations not shown. ) Loads listed address hanger/header/fastener limitations as well as joist/hanger limitations assuming header material is Douglas Fir-Larch (DF-L), Southern Pine (SP), or Microllam LVL, Parallam PSL, or TimberStrand LSL. Joist reaction should be checked by a qualified designer to ensure proper hanger selection. 3) Uplift loads have been increased 60% for wind or seismic loads and no further increase shall be permitted. Reduce loads according to code for normal duration loading such as cantilever construction. 4) If hanger height is less than 60% of joist height, joist rotation may occur, therefore supplemental lateral restraints are required, see page 4. 5) The type and quantity of fasteners used to install products is critical to connector performance. To achieve the allowable loads shown in this catalog, install with the fasteners specified for that particular product. All specified fasteners must be properly installed prior to applying load of any kind to the connection. 6) Throughout this guide, dimensions are expressed in inches and loads in pounds, unless specifically noted otherwise. 7) Load values for 10d and 16d designations in the fastener schedules throughout this catalog refer to common wire nails, unless noted otherwise. 8) The allowable loads shown in this catalog are based on Allowable Stress Design methodology. 9) Multiple TJI Joist Plies: Fasten together multiple plies of wood TJI Joist s, in accordance with Weyerhaeuser s installation guidelines, such that the joists act as a single unit. 10) Sloped TJI Joists: Use sloped seat hangers and beveled web stiffeners whenever the slope exceeds the following: 1/:1 for seat bearing lengths of -1/ or less; 3/8:1 for bearing lengths between -1/ and 3-1/ ; and 1/4:1 for bearing lengths in excess of 3-1/. Backer Blocks Pattern the nails used to install backer blocks or web stiffeners in wood TJI Joist s to avoid splitting the block. The nail pattern should be sufficiently spaced to avoid the same grain line, particularly with solid sawn backer blocks. Backer blocks must be installed on wood TJI Joist s acting as the header, or supporting member. Install in accordance with the Weyerhaeuser installation guidelines. The nails used to install hangers mounted to a TJI Joist header must penetrate through the web and into the backer block on the opposite side. Filler Block Installation:. Attach per table below. Backer Block Installation: Install tight to top flange (tight to bottom flange with face mount hangers). Attach per table to the right. Typical THO backer block installation Web Stiffener Attachment for TJI Joists 1 for TJI 110, 10, 30, 360 joists 1-1/ for TJI 560, 560D joists Gap 1/8 Gap 1/8 Typical THF backer block installation Backer Block (both sides) of web with single TJI Joist. Gap 1/8 Varies. See Table to the right With top flange hangers, backer block required only for downward loads exceeding 50 lbs or for uplift conditions Gap: 1/8 minimum -3/4 maximum Nailing: See table to the right Backer Block each side Web stiffener each side See table to the right Tight fit Filler and Backer Block sizes TJI Depth Type 1 Filler / Backer Size Nail Quantity Filler x6 10 Backer Filler x8 10 Backer 10 Filler 10 Backer Filler 10 Backer 10 Filler 10 Backer 10 Filler 10 Backer 10 Filler 10 Backer Filler 10 Backer 10 Filler Backer 15 Filler Backer x6 10 Filler Backer x8 10 Filler Backer x D Filler Backer x1 15 Filler Backer 15 1 Nailing Requirements Minimum Web No. of Nails TJI Depth Stiffener Size Type End Int 110 All 1 8d All 1 8d All 1 8d All 1 8d All x4 16d D x4 16d PS1 or PS sheathing, face grain vertical Construction grade or better 3 560D joists. Customer Service / Technical Assistance Burnsville, MN Corporate Office /

3 EWP INSTALLATION Support Height & Lateral Stability Hangers for joists without web stiffeners must support the TJI Joist s top flange and provide lateral resistance with no more than 1 8 horizontal deflection. Resist lateral movement 1/8 maximum gap Hangers for joists with web stiffeners must support a minimum of 60% of joist depth, or potential joist rotation must be addressed. Web stiffener Joist depth 60% min. of joist depth 3 (Top flange support requirements can be verified in EWP Top Mount Hangers charts under the Web Stiffener Req. column of s Product Catalog.) Nailer Installations Correct Hanger Attachment to Nailer A nailer or sill plate is considered to be any wood member attached to a steel beam, concrete block wall, concrete stem wall (or other type of support unsuitable for nailing), which is used as a nailing surface for top mount hangers to support beams or joists. Nailer Sized Correctly Top flange of hanger is fully supported and recommended nails have full penetration into nailer, resulting in a carried member hanging safely at the proper height. The nailer must be sized to fit the support width as shown and be of sufficient thickness to satisfy recommended top flange nailing requirements. A design professional must specify nailer attachment to steel beams. Wrong Nailer Size Causes Component Failure Avoid direct contact between hangers and steel beams, which may cause squeaks 1/4 Max. 1/4 Max. Too Narrow Top flange not fully supported can cause nail breakout. Or, by fully supporting top flange, hanger is tilted back, causing lifting of carried member which results in uneven surfaces and squeaky floors. Too Wide Loading can cause cross grain splitting of nailer. The recommended nailer overhang is 1 4 maximum per side.!!! Too Thin Top flange nailing cannot fully penetrate nailer, causing reduced allowable loads. Never use hangers which require multiple face nails since the allowable loads are dependent on all nail holes being used. Top Flange Hangers The thickness of the hanger metal and nail heads on top mount hangers must be evaluated for the effect on subsequent sheathing. Ensure the top mount hanger is installed so the flanges of the hanger are not over-spread which tends to elevate the supported I-Joist, causing uneven floor surfaces and squeaking. Similarly, ensure the hanger is installed plumb such that the face flanges of the hanger are mounted firmly against the wide-face surface of the header. Flush framing! Hanger over-spread! Hanger not plumb info@connectors.com Copyright 013 MiTek USA, Inc

4 4 SINGLE TJI JOISTS Joist Height Stock No. 1 D Dim 6 Top Mount Hangers 4,7 Face Mount Hangers Fastener Schedule 5 DF-L/SP Fastener Schedule 5 Uplift Down D Header Joist 160% 3 100% Stock No. 1 Dim 6 Header Joist DF-L/SP Uplift 160% 3 TJI / THO17950 (6) 10d () 10d x 1-1/ THF1795 Min (8) 10d () 10d x 1-1/ THF1795 Max (1) 10d /8 THO17118 (6) 10d () 10d x 1-1/ THF1711 Min (8) 10d () 10d x 1-1/ THF1711 Max (16) 10d TFL1714 (6) 10d () 10d x 1-1/ THF17140 Min (1) 10d () 10d x 1-1/ THF17140 Max (0) 10d 80 TJI / TFL095 (6) 10d () 10d x 1-1/ THF095 Min (8) 10d () 10d x 1-1/ THF095 Max (1) 10d /8 TFL0118 (6) 10d () 10d x 1-1/ THF011 Min (8) 10d () 10d x 1-1/ THF011 Max (16) 10d TFL014 (6) 10d () 10d x 1-1/ THF0140 Min (1) 10d () 10d x 1-1/ THF0140 Max (0) 10d TFL016 (6) 10d () 10d x 1-1/ THF /8 (4) 10d () 10d x 1-1/ TJI / TFL395 (6) 10d () 10d x 1-1/ THF395-1/ (1) 10d () 10d x 1-1/ /8 TFL3118 (6) 10d () 10d x 1-1/ THF3118-1/ (14) 10d () 10d x 1-1/ TFL314 (6) 10d () 10d x 1-1/ THF3140-1/ (18) 10d () 10d x 1-1/ TFL316 (6) 10d () 10d x 1-1/ THF3160-1/ () 10d () 10d x 1-1/ TJI /8 TFL3118 (6) 10d () 10d x 1-1/ THF3118-1/ (14) 10d () 10d x 1-1/ TFL314 (6) 10d () 10d x 1-1/ THF3140-1/ (18) 10d () 10d x 1-1/ TFL316 (6) 10d () 10d x 1-1/ THF3160-1/ () 10d () 10d x 1-1/ TFI3518-1/ (6) 16d () 10d x 1-1/ THF3180-1/ (4) 10d (8) 10d x 1-1/ TFI350-1/ (6) 16d () 10d x 1-1/ THF3180-1/ (4) 10d (8) 10d x 1-1/ TJI /8 THO /8 (10) 10d () 10d x 1-1/ THF3511-1/ (16) 10d () 10d x 1-1/ THO /8 (1) 10d () 10d x 1-1/ THF / (0) 10d () 10d x 1-1/ THO /8 (1) 10d () 10d x 1-1/ THF / () 10d () 10d x 1-1/ TFI418-1/ (6) 16d () 10d x 1-1/ THF / () 10d () 10d x 1-1/ TFI40-1/ (6) 16d () 10d x 1-1/ THF / () 10d () 10d x 1-1/ TJI 560D 18 TFI418-1/ (6) 16d () 10d x 1-1/ THF / () 10d () 10d x 1-1/ TFI40-1/ (6) 16d () 10d x 1-1/ THF / () 10d () 10d x 1-1/ TFI4-1/ (10) 16d () 10d x 1-1/ THF / () 10d () 10d x 1-1/ TFI44-1/ (10) 16d () 10d x 1-1/ THF / () 10d () 10d x 1-1/ ) Shaded hangers require web stiffeners at joist ends. Web stiffeners may be required for non-shaded hangers by Weyerhaeuser. ) Loads listed are based on hanger attachment to a DF-L or SP species solid sawn, Microllam LVL, Parallam PSL, or TimberStrand LSL header. Contact your local Weyerhaeuser or Structural Connectors Technical Representative for additional duration of load values. 3) Uplift loads have been increased 60% for wind and seismic loading; no further increase shall be permitted. 5) 10d x 1-1/ nails are 0.148" diameter x 1-1/" long, 10d nails are 0.148" diameter x 3" long, and 16d nails are 0.16" diameter x 3-1/" long. 6) D Dim is the length of the hanger seat. 7) For top mount hangers supported by TJI Down 100% THO TFL TFI H W THF single Additional diamond nail holes for maximum nailing Standard round nail holes for minimum nailing Patented dimple allows 45 nailing Customer Service / Technical Assistance Burnsville, MN Corporate Office /

5 SINGLE TJI JOISTS 5 Joist Height TJI % Adjustable Height Field Slope & Skew Skewed 45 Hangers Fastener Schedule 4 DF-L/SP Fastener Schedule 4,7 DF-L/SP Fastener Schedule 4,7 Uplift Down D Uplift Down D Header Joist 160% 3 Stock No. 1 Dim 8 Header Joist 160% 3 100% Stock No. 1,6 Dim 8 Header Joist 9-1/ LSSH179 3 (10) 10d (7) 10d x 1-1/ SKH170L/R 1-7/8 (14) 10d (10) 10d x 1-1/ / LSSH179 3 (10) 10d (7) 10d x 1-1/ SKH170L/R 1-7/8 (14) 10d (10) 10d x 1-1/ MSH17 1-3/4 (6) 10d (4) 10d x 1-1/ LSSH179 3 (10) 10d (7) 10d x 1-1/ SKH170L/R 1-7/8 (14) 10d (10) 10d x 1-1/ TJI / LSSH0 3 (10) 10d (7) 10d x 1-1/ SKH00L/R 1-7/8 (14) 10d (10) 10d x 1-1/ /8 MSH0 1-3/4 (6) 10d (4) 10d LSSH0 3 (10) 10d (7) 10d x 1-1/ SKH00L/R 1-7/8 (14) 10d (10) 10d x 1-1/ MSH0 1-3/4 (6) 10d (4) 10d LSSH0 3 (10) 10d (7) 10d x 1-1/ SKH00L/R 1-7/8 (14) 10d (10) 10d x 1-1/ MSH0 1-3/4 (6) 10d (4) 10d LSSH0 8 3 (10) 10d (7) 10d x 1-1/ SKH04L/R 1-7/8 (16) 10d (10) 10d x 1-1/ TJI / LSSH3 3 (10) 10d (7) 10d x 1-1/ SKH30L/R 1-7/8 (14) 10d (10) 10d x 1-1/ / LSSH3 3 (10) 10d (7) 10d x 1-1/ SKH30L/R 1-7/8 (14) 10d (10) 10d x 1-1/ LSSH3 3 (10) 10d (7) 10d x 1-1/ SKH34L/R 1-7/8 (16) 10d (10) 10d x 1-1/ MSH3 1-3/4 (6) 10d (4) 10d x 1-1/ LSSH3 7 3 (10) 10d (7) 10d x 1-1/ SKH34L/R 1-7/8 (16) 10d (10) 10d x 1-1/ TJI / LSSH3 3 (10) 10d (7) 10d x 1-1/ SKH30L/R 1-7/8 (14) 10d (10) 10d x 1-1/ LSSH3 3 (10) 10d (7) 10d x 1-1/ SKH34L/R 1-7/8 (16) 10d (10) 10d x 1-1/ MSH3 1-3/4 (6) 10d (4) 10d x 1-1/ LSSH3 7 3 (10) 10d (7) 10d x 1-1/ SKH34L/R 1-7/8 (16) 10d (10) 10d x 1-1/ MSH3 1-3/4 (6) 10d (4) 10d x 1-1/ LSSH3 7 3 (10) 10d (7) 10d x 1-1/ SKH34L/R 1-7/8 (16) 10d (10) 10d x 1-1/ LSSH3 7 3 (10) 10d (7) 10d x 1-1/ SKH34L/R 7 1-7/8 (16) 10d (10) 10d x 1-1/ TJI /8 MSH4 1-3/4 (6) 10d (6) 10d LSSH35 3 (14) 16d (1) 10d x 1-1/ SKH410L/R 5-1/ (16) 16d (10) 16d LSSH35 3 (14) 16d (1) 10d x 1-1/ SKH414L/R 5-1/ () 16d (10) 16d See current Product Catalog or LSSH (14) 16d (1) 10d x 1-1/ SKH414L/R 5-1/ () 16d (10) 16d Weyerhaeuser software for specialty hanger options LSSH (14) 16d (1) 10d x 1-1/ SKH414L/R 5-1/ () 16d (10) 16d LSSH (14) 16d (1) 10d x 1-1/ SKH414L/R 5-1/ () 16d (10) 16d TJI 560D Stock No. 1,6 D Dim 8 18 LSSH (14) 16d (1) 10d x 1-1/ SKH414L/R 5-1/ () 16d (10) 16d See current Product Catalog or LSSH (14) 16d (1) 10d x 1-1/ SKH414L/R 5-1/ () 16d (10) 16d Weyerhaeuser software for specialty hanger options LSSH (14) 16d (1) 10d x 1-1/ LSSH (14) 16d (1) 10d x 1-1/ ) Shaded hangers require web stiffeners at joist ends. ) Loads listed are based on hanger attachment to a DF-L or SP species solid sawn, Microllam LVL, Parallam PSL, or TimberStrand LSL header. Contact your local Weyerhaeuser or Structural Connectors Technical Representative for additional duration of load values. 3) Uplift loads have been increased 60% for wind and seismic loading; no further increase shall be permitted. 4) 10d x 1-1/ nails are 0.148" diameter x 1-1/" long, 10d nails are 0.148" diameter x 3" long, and 16d nails are 0.16" diameter x 3-1/" long. 5) Miter cut required on end of joist to achieve design loads. 6) For additional sizes, stock numbers, and modifications not shown, refer to 's Product Catalog. 7) Supplemental lateral support connection recommended when hanger height is less than 60% of joist height. 8) D Dim is the length of the hanger seat. DF-L/SP Uplift 160% 3 Down 100% LSSH Installation: Use all specified fasteners. Steps: 1. Position LSSH connector against plumb-cut end of joist. Fasten joist side flanges on both sides with 10d (0.148 ) x 1-1/ nails. Bend seat up to fit against joist bottom and drive (1) 10d (0.148 ) x 1-1/ nail through bottom seat into joist bottom flange. Drive () 10d (0.148 ) x 1-1/ nail at downward angle through dimpled nailing guides.. Lean connector and rafter end against ridge beam at desired position. Install 10d (0.148 x 3 ) or 16d (0.16 x 3-1/ ) nails through nail holes into ridge beam at right 90 angle. If skewing the rafter, only drive nails into ridge beam on inside flange. 3. Bend flange to desired angle. 4. Hammer outside flange until edge touches header. Fasten outside flange to ridge by driving 10d (0.148 x 3 ) or 16d (0.16 x 3-1/ ) nails through nail holes. Web stiffeners are required for all wood I-Joist installations. Designer may consider adding a tension restraint for the supported member for roof slopes exceeding 6/1. MSH skew to 45 maximum 1 3 & 4 SKH_L left shown LSSH info@connectors.com Copyright 013 MiTek USA, Inc

6 6 DOUBLE TJI JOISTS Joist Height Stock No. 1 Double TJI 110 Face Mount Hangers Fastener Schedule 5 DF-L/SP Fastener Schedule 5 Uplift Down D Header Joist 160% 3 100% Stock No. 1 Dim 6 Header Joist 9-1/ THO /8 (10) 10d () 10d x 1-1/ THF3595-1/ (1) 10d () 10d x 1-1/ /8 THO /8 (10) 10d () 10d x 1-1/ THF3511-1/ (16) 10d () 10d x 1-1/ THO /8 (1) 10d () 10d x 1-1/ THF / (0) 10d () 10d x 1-1/ Double TJI / THO (10) 16d (6) 10d THF / (1) 10d (6) 10d /8 THO (10) 16d (6) 10d THF / (16) 10d (6) 10d THO (10) 16d (6) 10d THF / (0) 10d (6) 10d THO (10) 16d (6) 10d THF / (0) 10d (6) 10d Double TJI / THO (10) 16d (6) 10d THF / (14) 10d (6) 10d /8 THO (10) 16d (6) 10d THF / (16) 10d (6) 10d THO (1) 16d (6) 10d THF / (0) 10d (6) 10d THO (1) 16d (6) 10d THF / (4) 10d (6) 10d Double TJI 360 D Dim 6 Top Mount Hangers 4,8 DF-L/SP Uplift 160% /8 THO (10) 16d (6) 10d THF / (16) 10d (6) 10d THO (1) 16d (6) 10d THF / (0) 10d (6) 10d THO (1) 16d (6) 10d THF / (4) 10d (6) 10d THO (14) 16d (6) 10d THF / (4) 10d (6) 10d THO300-3 (14) 16d (6) 10d THF / (4) 10d (6) 10d Double TJI /8 BPH (10) 16d (6) 10d HD710-1/ (16) 16d (6) 10d BPH (10) 16d (6) 10d HD7140-1/ (0) 16d (8) 10d BPH (10) 16d (6) 10d HD7160-1/ (4) 16d (8) 10d BPH (10) 16d (6) 10d HD7160-1/ (4) 16d (8) 10d BPH710 3 (10) 16d (6) 10d HD7160-1/ (4) 16d (8) 10d Double TJI 560D 18 BPH (10) 16d (6) 10d HD7160-1/ (4) 16d (8) 10d BPH710 3 (10) 16d (6) 10d HD7160-1/ (4) 16d (8) 10d BPH71 3 (10) 16d (6) 10d HD7160-1/ (4) 16d (8) 10d BPH714 3 (10) 16d (6) 10d HD7160-1/ (4) 16d (8) 10d ) Shaded hangers require web stiffeners at joist ends. Web stiffeners may be required for non-shaded hangers by Weyerhaeuser. ) Loads listed are based on hanger attachment to a DF-L or SP species solid sawn, Microllam LVL, Parallam PSL, or TimberStrand LSL header. Contact your local Weyerhaeuser or Structural Connectors Technical Representative for additional duration of load values. 3) Uplift loads have been increased 60% for wind and seismic loading; no further increase shall be permitted. 4) Top Mount Hangers require minimum 3" header width for THO series hangers; 3-1/" minimum header thickness for all other stock numbers. 5) 10d x 1-1/ nails are 0.148" diameter x 1-1/" long, 10d nails are 0.148" diameter x 3" long, and 16d nails are 0.16" diameter x 3-1/" long. 6) D Dim is the length of the hanger seat. 7) For top mount hangers supported by TJI Down 100% THO Double BPH THF Double HD Customer Service / Technical Assistance Burnsville, MN Corporate Office /

7 DOUBLE TJI JOISTS 7 Adjustable Height Field Slope & Skew Skewed 45 Hangers Fastener Schedule 4 DF-L/SP Fastener Schedule 4 DF-L/SP Fastener Schedule 4 DF-L/SP Joist D Uplift Down D Uplift Down D Uplift Down Height Stock No. 1,5 Dim 6 Header Joist 160% 3 100% Stock No. 1,5 Dim 6 Header Joist 160% 3 100% Stock No. 1 Dim 6 Header Joist 160% 3 100% Double TJI / MSH4 1-3/4 (6) 10d (6) 10d LSSH35 3 (14) 16d (1) 10d x 1-1/ SKH410L/R 7-1/ (16) 16d (10) 16d /8 MSH4 1-3/4 (6) 10d (6) 10d LSSH35 3 (14) 16d (1) 10d x 1-1/ SKH410L/R 7-1/ (16) 16d (10) 16d LSSH35 3 (14) 16d (1) 10d x 1-1/ SKH410L/R 7-1/ (16) 16d (10) 16d Double TJI / SKH00L/R / (14) 10d (10) 10d /8 See current Product Catalog or See current Product Catalog or SKH00L/R / (14) 10d (10) 10d Weyerhaeuser software for specialty hanger options Weyerhaeuser software for specialty hanger options SKH04L/R / (16) 10d (10) 10d SKH04L/R / (16) 10d (10) 10d Double TJI / MSH3-1-3/4 (6) 10d (4) 10d SKH30L/R / (14) 10d (10) 10d /8 MSH3-1-3/4 (6) 10d (4) 10d See current Product Catalog or SKH30L/R / (14) 10d (10) 10d MSH3-1-3/4 (6) 10d (4) 10d Weyerhaeuser software for specialty hanger options SKH34L/R / (16) 10d (10) 10d SKH34L/R / (16) 10d (10) 10d Double TJI /8 MSH3-1-3/4 (6) 10d (4) 10d SKH30L/R / (14) 10d (10) 10d MSH3-1-3/4 (6) 10d (4) 10d SKH34L/R / (16) 10d (10) 10d See current Product Catalog or SKH34L/R / (16) 10d (10) 10d Weyerhaeuser software for specialty hanger options SKH34L/R / (16) 10d (10) 10d Double TJI /8 MSH4- (8) 16d (6) 16d HD710-SK45L/R 7,8-1/ (16) 16d (6) 10d HD7140-SK45L/R 7,8-1/ (0) 16d (8) 10d See current Product Catalog or See current Product Catalog or Weyerhaeuser software for specialty hanger options HD7160-SK45L/R 7,8-1/ (4) 16d (8) 10d Weyerhaeuser software for specialty hanger options HD7160-SK45L/R 7,8-1/ (4) 16d (8) 10d HD7160-SK45L/R 7,8-1/ (4) 16d (8) 10d Double TJI 560D 18 HD7160-SK45L/R 7,8-1/ (4) 16d (8) 10d See current Product Catalog or See current Product Catalog or HD7160-SK45L/R 7,8-1/ (4) 16d (8) 10d Weyerhaeuser software for specialty hanger options Weyerhaeuser software for specialty hanger options HD7160-SK45L/R 7,8-1/ (4) 16d (8) 10d HD7160-SK45L/R 7,8-1/ (4) 16d (8) 10d ) Shaded hangers require web stiffeners at joist ends. ) Loads listed are based on hanger attachment to a DF-L or SP species solid sawn, Microllam LVL, Parallam PSL, or TimberStrand LSL header. Contact your local Weyerhaeuser or Structural Connectors Technical Representative for additional duration of load values. 3) Uplift loads have been increased 60% for wind and seismic loading; no further increase shall be permitted. 4) 10d x 1-1/ nails are 0.148" diameter x 1-1/" long, 10d nails are 0.148" diameter x 3" long, and 16d nails are 0.16" diameter x 3-1/" long. 5) For additional sizes, stock numbers, and modifications not shown, refer to 's Product Catalog. 6) D Dim is the length of the hanger seat. 7) Miter cut required on end of joist to achieve design loads. 8) Hangers are special order. Consult to for pricing and lead times. LSSH Installation: Use all specified fasteners. Steps: 1. Position LSSH connector against plumb-cut end of joist. Fasten joist side flanges on both sides with 10d (0.148 ) x 1-1/ nails. Bend seat up to fit against joist bottom and drive (1) 10d (0.148 ) x 1-1/ nail through bottom seat into joist bottom flange. Drive () 10d (0.148 ) x 1-1/ nail at downward angle through dimpled nailing guides.. Lean connector and rafter end against ridge beam at desired position. Install 10d (0.148 x 3 ) or 16d (0.16 x 3-1/ ) nails through nail holes into ridge beam at right 90 angle. If skewing the rafter, only drive nails into ridge beam on inside flange. 3. Bend flange to desired angle. 4. Hammer outside flange until edge touches header. Fasten outside flange to ridge by driving 10d (0.148 x 3 ) or 16d (0.16 x 3-1/ ) nails through nail holes. Web stiffeners are required for all wood I-Joist installations. Designer may consider adding a tension restraint for the supported member for roof slopes exceeding 6/1. MSH skew to 45 maximum 1 3 & 4 SKH_L Double left shown LSSH info@connectors.com Copyright 013 MiTek USA, Inc

8 8 MICROLLAM LVL, PARALLAM PSL, OR TIMBERSTRAND LSL BEAMS & HEADERS Joist Height Fastener Schedule 4 Down 100% 1 Fastener Schedule 4 Uplift D Header Joist 160% LVL PSL LSL Stock No. Dim 7 Header Joist 7-1/4 PHXU /4 (8) 16d (6) 10d x 1-1/ HD1770 (14) 16d (4 10d x 1-1/ /4 9-1/ 11-1/4 11-7/8 14 Stock No. 6 D Dim 7 Top Mount Hangers 3 BPH1795-3/8 (10) 16d (4) 10d x 1-1/ HD1795 (18) 16d (6) 10d x 1-1/ PHXU /4 (8) 16d (6) 10d x 1-1/ HUS (30) 16d (10) 16d THO17950 (6) 10d () 10d x 1-1/ HD1795 (18) 16d (6) 10d x 1-1/ PHXU /4 (8) 16d (6) 10d x 1-1/ HUS (30) 16d (10) 16d BPH1711-3/8 (10) 16d (4) 10d x 1-1/ HD1711 () 16d (6) 10d x 1-1/ PHXU /4 (8) 16d (6) 10d x 1-1/ HUS (30) 16d (10) 16d THO17118 (6) 10d () 10d x 1-1/ HD1711 () 16d (6) 10d x 1-1/ PHXU /4 (8) 16d (6) 10d x 1-1/ HUS (30) 16d (10) 16d BPH1714-3/8 (10) 16d (4) 10d x 1-1/ HD1714 (6) 16d (8) 10d x 1-1/ PHXU /4 (8) 16d (6) 10d x 1-1/ HUS (30) 16d (10) 16d Face Mount Hangers 7-1/4 PHXU /4 (8) 16d (6) 10d THD48 3 (8) 16d (16) 10d /4 PHXU /4 (8) 16d (6) 10d THD410 3 (38) 16d (0) 10d HLBH (15) NA16D-RS (6) 16d THDH (46) 16d (1) 16d / PHXU /4 (8) 16d (6) 10d THD410 3 (38) 16d (0) 10d HLBH (15) NA16D-RS (6) 16d THDH (46) 16d (1) 16d /4 PHXU /4 (8) 16d (6) 10d THD410 3 (38) 16d (0) 10d HLBH (15) NA16D-RS (6) 16d THDH (56) 16d (14) 16d /8 PHXU /4 (8) 16d (6) 10d THD410 3 (38) 16d (0) 10d HLBH (15) NA16D-RS (6) 16d THDH (56) 16d (14) 16d PHXU /4 (8) 16d (6) 10d THD410 3 (38) 16d (0) 10d HLBH (15) NA16D-RS (6) 16d THDH (66) 16d (16) 16d PHXU /4 (8) 16d (6) 10d THD41 3 (48) 16d (0) 10d HLBH (15) NA16D-RS (6) 16d THDH (66) 16d (16) 16d PHXU /4 (8) 16d (6) 10d THD41 3 (48) 16d (0) 10d HLBH (15) NA16D-RS (6) 16d THDH (66) 16d (16) 16d PHXU /4 (8) 16d (6) 10d THD414 3 (58) 16d (0) 10d HLBH350 6 (15) NA16D-RS (6) 16d THDH (66) 16d (16) 16d PHXU35 3-1/4 (8) 16d (6) 10d HD416-1/ (6) 16d (1) 10d PHXU /4 (8) 16d (6) 10d HD416-1/ (6) 16d (1) 10d ) Loads listed are based on hanger attachment to a DF-L or SP species solid sawn, Microllam LVL, Parallam PSL, or TimberStrand LSL header. Contact your local Weyerhaeuser or Structural Connectors Technical Representative for additional duration of load values. ) Uplift loads have been increased 60% for wind and seismic loading; no further increase shall be permitted. 4) 10d x 1-1/ nails are 0.148" diameter x 1-1/" long, 10d nails are 0.148" diameter x 3" long, and 16d nails are 0.16" diameter x 3-1/" long. 5) Joist nails need to be toe nailed at a 30 to 45 angle to achieve listed loads for THDH and HUS models. 7) D Dim is the length of the hanger seat. Uplift 160% Down 100% 1 THO BPH HD HUS Customer Service / Technical Assistance Burnsville, MN Corporate Office /

9 MICROLLAM LVL, PARALLAM PSL, OR TIMBERSTRAND LSL BEAMS & HEADERS 9 Joist Height D Dim 7 Top Mount Hangers 3 Face Mount Hangers Fastener Schedule 4 Uplift Down 100% 1 Fastener Schedule 4 160% D Uplift Down Header Joist LVL PSL LSL Stock No. Dim 7 Header Joist 160% 100% 1 LSL 7-1/4 BPH5575-1/4 (10) 16d (6) 10d /4 PHXU /4 (8) 16d (6) 10d THD610 3 (38) 16d (0) 10d HLBH (15) NA16D-RS (6) 16d THDH (46) 16d (16) 16d / PHXU /4 (8) 16d (6) 10d THD610 3 (38) 16d (0) 10d HLBH (15) NA16D-RS (6) 16d THDH (46) 16d (16) 16d /4 PHXU /4 (8) 16d (6) 10d THD610 3 (38) 16d (0) 10d HLBH (15) NA16D-RS (6) 16d THDH (56) 16d (0) 16d /8 PHXU /4 (8) 16d (6) 10d THD610 3 (38) 16d (0) 10d HLBH (15) NA16D-RS (6) 16d THDH (56) 16d (0) 16d PHXU /4 (8) 16d (6) 10d THD610 3 (38) 16d (0) 10d HLBH (15) NA16D-RS (6) 16d THDH (66) 16d () 16d PHXU /4 (8) 16d (6) 10d THD61 3 (48) 16d (0) 10d HLBH (15) NA16D-RS (6) 16d THDH (66) 16d () 16d PHXU /4 (8) 16d (6) 10d THD61 3 (48) 16d (0) 10d HLBH (15) NA16D-RS (6) 16d THDH (66) 16d () 16d PHXU /4 (8) 16d (6) 10d THD614 3 (58) 16d (0) 10d HLBH550 6 (15) NA16D-RS (6) 16d THDH (66) 16d () 16d HD516-1/ (30) 16d (1) 10d LSL 9-1/4 9-1/ 11-1/4 11-7/ Stock No. 6 PHXU /4 (8) 16d (6) 10d THD710 3 (38) 16d (0) 16d HLBH (15) NA16D-RS (6) 16d THDH (46) 16d (1) 16d PHXU /4 (8) 16d (6) 10d THD710 3 (38) 16d (0) 16d HLBH (15) NA16D-RS (6) 16d THDH (46) 16d (1) 16d PHXU /4 (8) 16d (6) 10d THD710 3 (38) 16d (0) 16d HLBH (15) NA16D-RS (6) 16d THDH (56) 16d (14) 16d PHXU /4 (8) 16d (6) 10d THD710 3 (38) 16d (0) 16d HLBH (15) NA16D-RS (6) 16d THDH (56) 16d (14) 16d PHXU /4 (8) 16d (6) 10d THD710 3 (38) 16d (0) 16d HLBH (15) NA16D-RS (6) 16d THDH (66) 16d (16) 16d PHXU /4 (8) 16d (6) 10d HD710-1/ (16) 16d (6) 10d HLBH (15) NA16D-RS (6) 16d THDH (66) 16d (16) 16d PHXU /4 (8) 16d (6) 10d HD7140-1/ (0) 16d (8) 10d HLBH (15) NA16D-RS (6) 16d THDH (66) 16d (16) 16d PHXU /4 (8) 16d (6) 10d HD7140-1/ (0) 16d (8) 10d HLBH710 6 (15) NA16D-RS (6) 16d THDH (66) 16d (16) 16d PHXU71 3-1/4 (8) 16d (6) 10d HD7160-1/ (4) 16d (8) 10d HLBH71 6 (15) NA16D-RS (6) 16d PHXU /4 (8) 16d (6) 10d HD7160-1/ (4) 16d (8) 10d HLBH714 6 (15) NA16D-RS (6) 16d See footnotes on page 9. PHXU HLBH THD THDH info@connectors.com Copyright 013 MiTek USA, Inc

10 10 VARIABLE PITCH CONNECTORS TMP & TMPH SERIES The TMP and TMPH is designed to make rafter-to-plate connections and eliminates time-consuming bird s-mouth notching or bevel plate installation. The TMP automatically adjusts to pitches from 1/1 to 6/1 and the TMPH from 6/1 to 14/1. Installation: Use all specified fasteners. Position connector on top plate. Fasten connector to outside of top plate with specified nails. Insert rafter into rafter pocket. Adjust rafter and pocket to correct pitch. Fasten rafter to connector with specified nails. Installing the TMP requires driving specified nails through the opposing slots in the pocket. TMPH installation involves sliding the fulcrum until it supports the pocket at the desired pitch and nailing down through the fulcrum base into the top plate to lock the fulcrum into position. Typical TMP installation Stock No. 1 TJI 110 Down Uplift 3 Header Joist 100% 160% TMP / (6) 10d (4) 10d x 1-1/ TMPH175 4 (10) 10d (8) 10d x 1-1/ TJI 10 TMP1 3-1/ (6) 10d (4) 10d x 1-1/ TMPH1 4 (10) 10d (8) 10d x 1-1/ TJI 30 TMP3 3-1/ (6) 10d (4) 10d x 1-1/ TMPH3 4 (10) 10d (8) 10d x 1-1/ TJI 360 TMP3 3-1/ (6) 10d (4) 10d x 1-1/ TMPH3 4 (10) 10d (8) 10d x 1-1/ TJI 560 TMP4 3-1/ (6) 10d (4) 10d x 1-1/ TMPH4 4 (10) 10d (8) 10d x 1-1/ TJI 560D D Dim 5 Pitch Range: TMP TMPH Fastener Schedule TMP4 3-1/ (6) 10d (4) 10d x 1-1/ TMPH4 4 (10) 10d (8) 10d x 1-1/ ) Shaded hangers require web stiffeners at joist ends. Web stiffeners may be required for non-shaded hangers by Weyerhaeuser. ) Loads listed are based on hanger attachment to a DF-L or SP species solid sawn, Microllam LVL, Parallam PSL, or TimberStrand LSL header. Loads are governed by test results; no further increase shall be permitted. 3) Uplift loads have been increased 60% for wind and seismic loading; no further increase shall be permitted. 5) D Dim is the length of the hanger seat. TMP Typical TMPH installation TMPH fulcrum Customer Service / Technical Assistance Burnsville, MN Corporate Office /

11 GENERAL INSTALLATION WS Series Wood Screw Applications - Joining, 3, or 4 Ply Microllam LVL Members Installation: Screws are self-drilling. Install using a low speed clutch drill with 3/8 hex head driver. The washer head should be flat to the surface and the serrations will oppose turning and release the clutch. Do not over-tighten the screws. For ply members, wood screws shall be installed with the screw heads in the loaded ply. For 3 or 4 ply members, wood screws shall be installed in both outer plys. Designer shall specify all wood screws locations. Increase edge and end distances if wood splitting occurs. Stagger all screws installed into the opposite face. A minimum of rows of screws shall be used for all members with H= 5-1/ and larger. H 1 1 / min 1 / min 1 / min 1 1 / min name 3/8 Recommended Row Guidelines Spacing 4 min. 4 max. Screw length 1 min. Recommended (Typ) Other Stagger patterns as approved by Engineer are acceptable L SH T WS Spacing 4 min. 4 max. Serrations 1/4 Beveled reamer Cut threads Self drilling point 4 min End of member 11 Figure 1 Figure Figure 3 Figure 4 Figure 5 Figure 6 WS35 installed in () Ply WS35 installed in (3) Ply WS6 installed in (4) Ply WS35 installed in (1) 1 3 4, (1) 3 1 Ply WS35 installed in () 1 3 4, (1) 3 1 Ply WS6 installed in () 31/ Ply Stock No. Dimensions (in) Ref. No. Description L SH T 3-1/ 3/4-3/ /4 4 Maximum Allowable Uniform Loads that can be applied to either outside member (Lbs. Per Lineal Ft.) 1,3,4,5,6 DF-L / SP Wood Screw Spacing Multiple Members Installation Figure,8 Rows Rows Rows Rows Rows Rows ) Based on Zscrew = 43 pounds in Douglas Fir-Larch ) Load values depicted assume all uniform load is applied 3) Except for Figure 6 installation, load values neglect any contribution of screws installed to opposite side, even 4) Loads are for normal (100%) duration of load, and may 5) Uniform loads in table represent the capacity of the less and should be checked by a qualified designer or wide beam to resist the applied load on one edge; otherwise, the loads shall be uniformly distributed across info@connectors.com Copyright 013 MiTek USA, Inc

12 Specification Tools All available on our Web Comprehensive Web Site Contains all literature in a printable.pdf format CAD Menu Program and Drawing Library downloads Quick and Easy literature ordering Register on-line at Web Site Watch Registration and automatically receive product updates through your CAD Menu Program Install a new Drop Down Menu in your AutoCAD menu bar (AutoCAD r14, AutoCAD 000, 000i, 00, 004, 005) Import scalable product drawings directly into your details or section drawings Available in 3-view format; top, front, and side where applicable JUS10- TOP VIEW JUS10- FRONT VIEW JUS10- SIDE VIEW CAD Library CAD Library contains over 350 illustrations in.dxf and.dwg formats Find drawings quickly by Stock No. or Reference No. High Wind Illustrations are also available Your Local Dealer / Distributor Weyerhaeuser Microllam, Parallam, Timberstrand and TJI are registered trademarks of Weyerhaeuser NR. Customer Service Burnsville, MN Phone: / Fax: Manufacturing: Montgomery, MN Livermore, CA Largo, FL Thornhill, Ontario Warehouses: Corona, CA Humble, TX Westampton, NJ Copyright 013 MiTek USA, Inc. Revised July 013