Series ZPT/ZPR. Vacuum Pad: Ball Joint Type. Pad diameters: ø10, ø13, ø16, ø20 ø25, ø32, ø40, ø50
|
|
- Berniece Hall
- 5 years ago
- Views:
Transcription
1 Vacuum Pad: all oint Type eries ZPT/ZPR Pad diameters: ø, ø1, ø, ø,, ø, ø0 joint type ideal for adsorption on slanted work surfaces all eries ZPT: Vertical vacuum entry type eries ZPR: Lateral vacuum entry type One-Touch fitting -11
2 Vacuum Pad: all oint Type eries ZPT/ZPR Pad diameters: ø, ø1, ø, ø,,, ø, ø0 Pad materials: NR, ilicon rubber, Urethane rubber, luoro rubber, onductive NR, onductive silicon rubber eries variations s ZPT eries Vertical vacuum entry ZPR eries Lateral vacuum entry uffer With buffer With buffer Mounting Male thread emale thread uffer mounting (male thread) emale thread uffer mounting (male thread) emale thread ual emale thread One-Touch fitting One-Touch fitting One-Touch fitting Page P..9-1 / 2 P..9- / 4 P..9- to 9 P..9- to 9 P..9-1 / 111 P to 11 dsorption is possible even on a slanted surface. Pad diameter uffer stroke uffer stroke ø ø1 ø ø ø ø0 nterchangeable with standard type. mm mm 0mm mm 0mm 1 Rotation ±1 xchangeable at the adapter. Pad materials and characteristics Material NR tem ilicon rubber Urethane rubber luoro rubber onductive NR onductive silicon rubber urometer (± ) Operating temperature range 0 to 1 0 to 0 0 to 60 0 to 0 to 0 to 0 Oil resistance (gasoline) Oil resistance (benzol) lkali resistance : Little or no effect : an be used depending on conditions : Not suitable cid resistance Weather resistance Ozone resistance brasion resistance Water resistance olvent resistance (benzene, toluene) The characteristics shown above represent the general properties of the rubber materials. Pad materials used by M meet material standards, however, even in pad tests similar to material tests, results differ depending upon shape and operating conditions. -114
3 Vertical Vacuum ntry eries ZPT Without uffer/male Thread Pad diameter ø 1 ø1 ø ø 2 2 ø 0 ø0 ow to Order ZPT 2 GN 8 M x 0.8 Mounting thread diameter male thread ymbol Thread Pad dia. 8 x 1 M x 1 ø to 14 ø, ø0 Pad type all joint Pad material N NR ilicon rubber U Urethane rubber luoro rubber GN onductive NR G onductive silicon rubber ø and larger are manufactured upon receipt of order. Note) Pads are exclusively ball joint type and are not interchangeable with other pads. tandard pecifications Weight Table (g) direction onnection Pad diameter ø to ø, ø0 all joint rotation Pad Types Vertical Mounting Male thread emale thread x 1 M x 1 M x 0.8 ±1 Mounting (female thread) Pad diameter (male thread) M x 0.8 ø to ø, ø0 x 1 M x 1 24 Pad type Pad diameter Material olour urometer Note NR 0 ilicon rubber White all joint ø, ø1, ø, ø,,, ø, ø0 Urethane rubber luoro rubber onductive NR rown with green mark with 1 white mark 0 onductive silicon rubber with 2 white marks 0 Note: hore urometer scale (±º) -11
4 eries ZPT Without uffer/male Thread ZPT /1/ --8 (Without uffer/male Thread) ZPT /2/2 -- (Without uffer/male Thread) Width across flats 14 M x 1 M x 0.8 x 1 M x Width across flats Width across flats 2 Width across flats Width across flats imensions imensions ZPT--8 ZPT1--8 ZPT ZPT-- ZPT2-- ZPT ZPT / (Without uffer/male Thread) M x 0.8 Width across flats 21. imensions ZPT ZPT
5 Vertical Vacuum ntry eries ZPT Without uffer/emale Thread ow to Order ZPT G 01 Pad diameter ø ø1 ø ø ø 0 ø0 Pad material N NR ilicon rubber U Urethane rubber Pad type all joint GN luoro rubber onductive NR G onductive silicon rubber onnection emale thread ymbol (same as mounting thread) ø and larger are manufactured upon receipt of order. Note) Pads are exclusively ball joint type and are not interchangeable with other pads Thread diameter M ø to ø, ø0 Pad diameter tandard pecifications Weight Table (g) direction onnection Pad diameter ø to Vertical Mounting/ emale thread M M Pad diameter ø to ø, ø0 (female thread) M ø, ø0 all joint rotation ±1 Pad Types Pad type Pad diameter Material olour urometer Note NR 0 ilicon rubber White Note: hore urometer scale (±º) all joint ø, ø1, ø, ø,,, ø, ø0 Urethane rubber luoro rubber onductive NR rown with green mark with 1 white mark 0 onductive silicon rubber with 2 white marks 0-117
6 ZPT /1/ - (Without uffer/emale Thread) ZPT /2/0 - /8/01 (Without uffer/emale Thread) Width across flats P N Width across flats 8 M NL Width across flats Width across flats 2 Width across flats imensions imensions N NL P ZPT- ZPT1- ZPT ZPT /0-8/01 (Without uffer/emale Thread) ZPT- ZPT-8 ZPT-01 ZPT2- ZPT2-8 ZPT2-01 ZPT M M M Width across flats P N ZPT2-8 ZPT NL. imensions N NL P ZPT-8 ZPT ZPT0-8 ZPT
7 Vertical Vacuum ntry eries ZPT With uffer ow to Order ZPT GN 04 Pad diameter N U GN G ø ø1 ø ø ø ø0 Pad type NR all joint Pad material ilicon rubber Urethane rubber luoro rubber onductive NR onductive silicon rubber ø and larger are manufactured upon receipt of order. uffer type Without detent K With detent Mounting thread diameter/male thread (Refer to Table 1 for applications.) (Refer to Table 1 for applications.) Table 1 /Mounting thread diameter Mounting thread diameter (male thread) Pad diameter ø to ø0 onnection Thread diameter, M x 1 Piping diameter ymbol 14 emale thread M 01 ø4 tube 04 One-Touch ø6 tube 06 fitting ø8 tube 08 uffer stroke ymbol troke Pad diameter ø to ø0 mm mm 0 0mm mm 0 0mm uffer spring reactive force Pad diameter 0 stroke 1.0N{0.kgf} ø to ø0 2.0N {0.kgf} troke end.0n{0.1kgf}.0n{0.1kgf} Note) Pads are exclusively ball joint type and are not interchangeable with other pads. Pad Types Pad type Pad diameter Material olour urometer Note NR 0 ilicon rubber White Note: hore urometer scale (±º) all joint ø, ø1, ø, ø,,, ø, ø0 Urethane rubber luoro rubber onductive NR rown with green mark with 1 white mark 0 onductive silicon rubber with 2 white marks 0-119
8 eries ZPT With uffer tandard pecifications onnection Pad diameter ø to ø0 all joint rotation Mounting uffer male thread M x 1 Vertical emale thread One-Touch fitting ø4 tube M ø6 tube ø6 tube ø8 tube ±1 uffer pecifications Pad diameter Mounting troke pring reactive force etent specifications M x 1,, 0,, 0 ø to ø0,, 0, 0 0 stroke troke end 1.0N {0.kgf}.0N {0.1kgf} 0 stroke troke end 2.0N {0.kgf}.0N {0.1kgf} Without detent (), With detent (K) Weight Table (g) Pad diameter ø to ø, ø0 emale thread One-Touch fitting M ø4 tube ø6 tube ø8 tube 19 7 dditional Weight by troke (g) Pad diameter ø to ø troke
9 ZPT /1/ /K -- (With uffer/emale Thread) eries ZPT ZPT /2/2 /K (With uffer/emale Thread) Width across flats 8 M Width across flats 1 M x 1 Width across flats 14 Width across flats 8 M Width across flats Width across flats Width across flats12 Width across flats imensions/mm stroke ZPT-- ZPT1-- 1 ZPT Width across flats 1 With a stroke of mm dditional dimensions by stroke troke Width across flats 7 Width across flats With a stroke of to 0mm imensions/mm stroke ZPT ZPT ZPT dditional dimensions by stroke troke + +. ± ±
10 eries ZPT With uffer ZPT /0 /K (With uffer/emale Thread) ZPT /1/ /K -0- (With uffer/one-touch itting) Width across flats 1 pplicable tube O.. øq 6.2 Width across flats 8 M M x 1 Width across flats 14 Width across flats 8 M Width across flats Width across flats 2. With a stroke of mm Width across flats 1 imensions/mm stroke Q:4 Q:6 K K ZPT ZPT ZPT-0-18 Width across flats dditional dimensions by stroke troke K K. With a stroke of to 0mm imensions/mm stroke ZPT ZPT dditional dimensions by stroke troke + +. ±
11 ZPT /2/2 /K (With uffer/one-touch itting) ZPT /0 /K (With uffer/one-touch itting) eries ZPT pplicable tube O.. øq pplicable tube O.. øq Width across flats P Width across flats P Width across flats K With a stroke of mm With a stroke of mm Width across flats P pplicable tube O.. øq Width across flats 7 Width across flats K K. Width across flats P pplicable tube O.. øq Width across flats 7 K imensions/mm stroke ZPT ZPT ZPT dditional dimensions by stroke troke ±0 With a stroke of to 0mm Q: 6 Q: 8 K P K P Q: 6 Q: 8 K P K P With a stroke of to 0mm imensions/mm stroke Q: 6 Q: 8 K P K P ZPT ZPT dditional dimensions by stroke troke Q: 6 Q: 8 K P K P ±
12 Lateral Vacuum ntry eries ZPR Without uffer/emale Thread ow to Order ZPR G 06 Pad diameter Mounting thread 1 2 ø ø1 ø ø diameter/female thread (Refer to Table 1 for applications.) (Refer to Table 1 for applications.) 2 Table 1 /Mounting thread diameter ø Mounting thread diameter 0 ø0 Pad diameter ø to ø0 Pad type onnection Thread diameter, M M Piping diameter ymbol 8 all joint ø4 tube 04 Pad material One-Touch fitting ø6 tube 06 N NR ø8 tube 08 ilicon rubber U Urethane rubber luoro rubber GN onductive NR G onductive silicon rubber Note) Pads are exclusively ball joint type and are not interchangeable with other pads. ø and larger are manufactured upon receipt of order. tandard pecifications Weight Table (g) direction onnection Pad diameter ø to ø0 Lateral onnection emale thread One-Touch fitting M ø4 tube ø6 tube M ø6 tube ø8 tube ø6 tube ø8 tube Pad diameter ø to ø, ø0 Mounting female thread M M M (One-Touch fitting) ø4 tube 18 ø6 tube ø8 tube all joint rotation ±1 Pad Types Pad type all joint Pad diameter ø, ø1, ø, ø,,, ø, ø0 Material olour urometer Note NR 0 ilicon rubber White Urethane rubber rown luoro rubber with green mark onductive NR with 1 white mark 0 onductive silicon rubber with 2 white marks 0 Note: hore urometer scale (±º) -124
13 ZPR /1/ -0- (Without uffer/emale Thread) ZPR /2/2-0- /8 (Without uffer/emale thread) eries ZPR Width across flats M x 0.8 pplicable tube O.. øq N pplicable tube O.. øq Width across flats ør ør 8 Width across flats Width across flats 2 imensions ZPR-0- ZPR1-0- ZPR imensions by tube diameter Pad diameter Q: 4 Q: 6 R R ZPR /0-0-8 (Without uffer/emale Thread) imensions ZPR-0- ZPR-0-8 ZPR2-0- ZPR2-0-8 ZPR2-0- ZPR imensions by tube diameter Pad diameter ø to Q: 6 Q: 8 R R N M M M N pplicable tube O.. øq ør 8. imensions ZPR-0-8 ZPR N 6 imensions by tube diameter Pad diameter ø, ø0 Q: 6 Q: 8 R R
14 Lateral Vacuum ntry eries ZPR With uffer ow to Order ZPR GN 0 06 Pad diameter ø 1 ø1 ø ø 2 2 ø 0 ø0 Pad type all joint Mounting thread diameter/male thread (Refer to Table 1 for applications.) (Refer to Table 1 for applications.) Table 1 /Mounting thread diameter Mounting thread diameter (male thread) Pad diameter ø to ø0 onnection Thread diameter, M x 1 Piping diameter ymbol 14 One-Touch fitting ø4 tube ø6 tube ø8 tube Pad material N NR ilicon rubber U Urethane rubber luoro rubber GN onductive NR G onductive silicon rubber ø and larger are manufactured upon receipt of order. uffer type Without detent K With detent uffer stroke ymbol troke mm mm 0 0mm mm 0 0mm Pad diameter ø to ø0 uffer spring reactive force Pad diameter ø to ø0 0 stroke 1.0N {0.kgf} 2.0N {0.kgf} troke end.0n {0.1kgf}.0N {0.1kgf} Note) Pads are exclusively ball joint type and are not interchangeable with other pads. Pad Types Pad type Pad diameter Material olour urometer Note NR 0 ilicon rubber White Note: hore urometer scale (±º) all joint ø, ø1, ø, ø,,, ø, ø0 Urethane rubber luoro rubber onductive NR rown with green mark with 1 white mark 0 onductive silicon rubber with 2 white marks 0-126
15 eries ZPR tandard pecifications direction onnection Pad diameter all joint rotation ø to ø0 Mounting Male thread M x 1 Lateral One-Touch fitting ø4 tube ø6 tube ø6 tube ø8 tube ±1 uffer pecifications Pad diameter Mounting troke pring reactive force etent specifications M x 1,, 0,, 0 ø to ø0,, 0, 0 0 stroke 1.0N {0.kgf} 0 stroke 2.0N {0.kgf} troke end.0n {0.1kgf} troke end.0n {0.1kgf} Without detent (), With detent (K) Weight Table (g) Pad diameter One-Touch fitting ø4 tube ø6 tube ø8 tube 4 ø to 8 9 ø, ø0 14 dditional Weight by troke (g) Pad diameter troke ø to ø
16 eries ZPR With uffer ZPR /1/ /K-0- (With uffer) M x 1 Width across flats 14 Width across flats pplicable tube O.. øq Width across flats Width across flats 2 imensions/mm stroke ZPR-0- ZPR ZPR Q: 4 Q: 6 R R dditional dimensions by stroke troke ZPR /2/2 /K-0-14 (With uffer) pplicable tube O.. øq Width across flats pplicable tube O.. øq Width across flats ør ør ør With a stroke of mm With a stroke of to 0mm imensions/mm stroke ZPR-0-14 ZPR ZPR Q: 6 Q: 8 R R dditional dimensions by stroke troke ±
17 ZPR /0 /K (With uffer) eries ZPR pplicable tube O.. øq pplicable tube O.. øq ør ør. With a stroke of mm. With a stroke of to 0mm imensions/mm stroke ZPR-0-14 ZPR Q: 6 Q: 8 R R dditional dimensions by stroke troke + ±
18 eries ZPT/ZPR pecific Product Precautions - Precautions on esign Warning 1. n cases where the work pieces are heavy or dangerous objects, etc., take measures to address a possible loss of adsorption force (installation of drop prevention guides, etc.). n the case of transportation by vacuum adsorption using vacuum pads, adsorption force is lost when there is a drop in vacuum pressure. urthermore, since vacuum pressure can also deteriorate due to wear and cracking of pads, and vacuum leakage from piping, etc., be certain to perform maintenance on vacuum equipment. election aution 1. The pad materials which can be used differ depending upon the operating environment. n appropriate pad material should be selected. urthermore, since vacuum pads are manufactured for use with industrial products, they should not come into direct contact with medicines or food products, etc. 2. epending upon the weight and shape of the work pieces, the diameter, quantity and shape of pads suitable for use will vary. Use the pad lifting force table for reference. lso, the pads to be selected will differ based upon conditions other than the above, such as the condition of the work piece surface (presence or absence of oil or water), the work piece material and its gas permeability. onfirmation is necessary by actually performing vacuum adsorption on the subject work pieces.. Use a buffer for adsorption on fragile work pieces. The cushioning performed by the buffer is also necessary when there is variation in the height of work pieces. When it is desired to perform further positioning of pads and work pieces, a detent buffer can be used. election aution 4. The life of the buffer will be reduced if lateral force is applied to the buffer shaft. Note that sometimes a load is applied to the buffer by a piping tube (pulling or pressing, etc. in a lateral direction).. o not apply an impact or large force to a pad when adsorbing a work piece. This will cause deformation, cracking and wear of the pad to be accelerated. The stiffening ribs, etc. should touch lightly, while staying within the pad skirt s deformation range. Positioning should be performed accurately. specially in the case of small diameter pads. 6. When transporting in an upward direction, factors such as acceleration, wind pressure and impact force must be considered in addition to the work piece weight. Use caution particularly when lifting items such as glass plates and circuit boards, because a large force will be applied by wind pressure. When a work piece which is oriented vertically is transported horizontally, large forces are applied by acceleration when movement is started and stopped. urther, in cases where the pad and work piece can slip easily, accelerations and decelerations of horizontal movement should be kept low. 7. When transporting flat shaped work pieces that have large surface areas using multiple pads, care must be taken in arranging the pads, giving consideration to balance of the work pieces. Maintenance aution 1. Perform pad maintenance regularly. ince pads are essentially rubber, deterioration is unavoidable. The rate of deterioration depends upon factors such as conditions of use, environment and temperature. Regular maintenance should be performed. f any damage, splitting, cracking or abrasion has occured in a pad which appears to be harmful, replace it immediately. lso, take care not to damage the outside of the pad. eteriorated pad Replacement of Pads aution Pad diameter: ø to 1. nsert a hexagon wrench from the bottom of the pad, loosen the screw and remove the old pad from the adapter. 2. Place a new pad on the adapter, and after confirming that the O-ring is in place, r e t i g h t e n dapter 1 the screw with the Pad h e x a g o n wrench. Pad diameter: ø, ø0 1. Pull the lock ring upward, and after lifting it to the adapter, remove the old pad by pulling it downward. 2. While holding the lock ring in the raised position, place a new pad onto the adapter.. onfirm that the pad is securely in place, and then return the lock ring to its original position. Replacement 2 exagon wrench dapter 1 New pad O-ring on inside 2 Lock ring Pad
19 ZPT eries Pad diameter: ø to ZPR eries Pad diameter: ø to 4 uffer 4 uffer dapter dapter 1 Pad 1 Pad With buffer With buffer Pad diameter: ø, ø0 Pad diameter: ø, ø0 4 uffer 4 uffer dapter dapter 2Lock ring 2 Lock ring 1 Pad 1 Pad With buffer With buffer Parts list No escription Material Note Pad NR, ilicon rubber, Urethane rubber, luoro rubber onductive NR, onductive silicon rubber Lock ring luminium dapter rass, U lectroless nickel plated uffer rass lectroless nickel plated dapter rass, U, PT lectroless nickel plated -11
20 eries ZPT/ZPR Replacement Parts Pad Unit Lock Ring Unit ow to Order ZP GN ow to Order ZPL Pad diameter ø 1 ø1 ø ø 2 2 ø 0 ø0 Pad type all joint Pad material N U NR ilicon rubber Urethane rubber luoro rubber GN onductive NR G onductive silicon rubber ø and larger are manufactured upon receipt of order. imensions b or ball joint pad (ø, ø0) uffer Mounting Nut Note) Pads are exclusively ball joint type and are not interchangeable with other pads. imensions all joint type: ø to ø N-01 N-01 Pad diameter ø to ø0 d M x ø all joint type: ø, ø0 ø ø ZP ZP1 ZP ZP ZP2 ZP2 ZP ZP
21 eries ZPT/ZPR Pad election The pad diameter is found by means of a pad lift calculation. The calculated value should be used for reference and confirmed by actual adsorption tests when necessary. n the lift calculation, consideration should be given to the weight of the work piece, forces due to acceleration during movement (lifting, stopping, turning, etc.) and a sufficient extra margin should be allowed. margin should also be allowed when determining the number and arrangement of pads. The theoretical lifting force of a pad can be found by calculation or from the theoretical lifting force table. alculation inding the Theoretical Lifting orce 1 W = P x x 0.1 x t P' 1 (W' = x 1.0 x x ) 760 t Theorectical Lifting orce Table W : Lifting force (N) W' : Lifting force (kgf) Pads P : Vacuum pressure (kpa) P' : Vacuum pressure (mmg) : Pad area (cm²) t : afety factor orizontal lifting: 4 or more Vertical lifting: 8 or more W orizontal lifting W Vertical This type of application (should basically be avoided.) The theoretical lifting force (not including the safety factor) is found from the pad diameter and vacuum pressure. The required lifting force is then found by dividing the theoretical lifting force by the safety factor. Pad diameter : Pad area cm² Vacuum pressure kpa {mmg} 8 {68} 80 {600} 7 {6} 70 {2} 6 {488} 60 {} {41} 0 {7} 4 {8} {00} Lifting force = Theoretical lifting force t 1. Theoretical lifting force table (Theoretical lifting force = P x x 0.1 {Theoretical lifting force = ø {0.680} 6.28 {0.6}.89 {0.601}.0 {0.61}. {0.} 4.71 {0.480} 4.2 {0.441}.9 {0.1}. {0.60}.14 {0.} ø {1.1}.6 {1.08} 9.98 {1.02} 9.1 {0.949} 8.6 {0.882} 7.98 {0.814} 7.2 {0.746} 6.6 {0.678}.99 {0.611}.2 {0.42} ø {1.74}.1 {1.64} 1.1 {1.4} 14.1 {1.44} 1.1 {1.4} 12.1 {1.2} 11.1 {1.1}.1 {1.0} 9.0 {0.92} 8.04 {0.8} ø {2.72} 2.1 {2.6} 2.6 {2.41} 22.0 {2.24}.4 {2.08} 18.8 {1.92} 17. {1.76} 1.7 {1.60} 14.1 {1.44} 12.6 {1.28} {4.2} 9. {4.01} 6.8 {.7} 4.4 {.1} 1.9 {.2} 29. {.01} 27.0 {2.7} 24.6 {2.1} 22.1 {2.2} 19.6 {2.00} P' x x 1.0}) 760 ø {6.96} 64. {6.6} 60. {6.1} 6. {.74} 2. {.} 48.2 {4.92} 44.2 {4.1}.2 {4.} 6.2 {.69} 2.2 {.28} {.9} 1 {.} 94. {9.64} 88.2 {8.99} 81.9 {8.} 7.6 {7.71} 69. {7.07} 6.0 {6.42} 6.7 {.78} 0.4 {.14} Unit: N(kgf) ø {17.0} 17 {.0} 147 {1.0} 17 {14.0} 127 {1.0} 118 {12.0} 8 {11.0} 98.0 {.0} 88.2 {8.99} 78.4 {7.99} aution 1. n cases such as those in which a flat item having a large surface area is carried by multiple pads, balance must be considered when determining the pad arrangement. dditionally, supplementary devices (for example, drop prevention guides) should be installed as necessary to prevent dropping of work pieces. Pad rop prevention guides -1
22 eries ZPT/ZPR ata alculation inding the Pad iameter pad diameter which allows for a safety factor based upon the work piece lifting method (horizontal or vertical), can be selected by using the calculation formula or the selection graphs (graphs 1 and 2 below). 4 ø =.14 x 760 P' x 1.0 x W' ( n ) x t x 00 ø = 4.14 x 1 P x W n x t x 00 election Graphs ø : Pad diameter W' : Lifting force (kgf) Pads n : Number of pads per work piece W : Lifting force (N) P : Vacuum pressure (kpa) P' : Vacuum pressure (mmg) t : afety factor orizontal lifting: 4 or more Vertical lifting: 8 or more W W orizontal lifting Vertical lifting This type of application (should basically be avoided.) fter establishing the work piece weight, number of pads to be used and the vacuum pressure when adsorbing the work piece, the pad diameters for horizontal lifting and vertical lifting can be found by means of selection graphs 1 and 2. election graph 1 Pad diameter selection graph by lifting force orizontal lifting (ø to ø0) election graph 2 Pad diameter selection graph by lifting force Vertical lifting (ø to ø0) Pad diameter kPa 70kPa 60kPa 0kPa kpa Pad diameter kPa 70kPa 60kPa 0kPa kpa Lifting force (N) Lifting force (N) ow to read the graphs xample: Work piece weight 1kg (lifting force: 9.8N) : onditions/number of pads ; pcs. Vacuum pressure 60kPa (mmg) orizontal lifting <election procedure> rom the conditions at the left, the lifting force per pad: 9.8N pcs. = 2N, and for horizontal lifting, selection is made from graph 1. Then, extending the intersection point of the lifting force 2N and the vacuum pressure 60kPa to the left, a pad diameter of 1mm is obtained. Therefore, a pad diameter of 1mm or greater should be selected. -14
Series ZPT/ZPR. Vacuum Pad: Ball Joint Type. Pad diameters: ø10, ø13, ø16, ø20 ø25, ø32, ø40, ø50 ZX ZR ZM ZY ZH ZU ZL ZF ZP ZCU CYV
Pad: all oint Type eries ZPT/ZPR all Pad diameters: ø, ø1, ø, ø,, ø, ø0 joint type ideal for adsorption on slanted work surfaces Z ZR ZM Z Z ZU ZL Z ZP ZU V related eries ZPT: Vertical vacuum entry type
More informationFully understand the features above and select the equipment that suits your operating conditions.
1 Features and Precautions for Vacuum Adsorption Vacuum adsorption system as a method to hold a workpiece has the following features. Easy construction Compatible with any place where adsorption is possible.
More informationAdsorption Plate. Specialized for adsorption and fixing in place of thin sheets, glass substrates, and soft workpieces. Series SP
dsorption Plate Series Specialized for adsorption and fixing in place of thin sheets, glass substrates, and soft workpieces. Z Z K MJ MV P HP quipment 1239 Ideal for adsorption and fixing in place of thin
More informationAdsorption Plate. SP Series. Specialized for adsorption and fixing in place of thin sheets, glass substrates, and soft workpieces.
dsorption Plate Series Specialized for adsorption and fixing in place of thin sheets, glass substrates, and soft workpieces. ZUK MJ J MV 749 Ideal for adsorption and fixing in place of thin sheets, glass
More informationAdsorption Plate. Specialized for adsorption and fixing in place of thin sheets, glass substrates, and soft workpieces. Series SP
dsorption Plate Series Specialized for adsorption and fixing in place of thin sheets, glass substrates, and soft workpieces. Z Z K MJ MV P HP Related quipment ourtesy of Steven ngineering, Inc.-230 Ryan
More information8-Ton Manual Splitter OWNER S MANUAL
8-Ton Manual Splitter OWNER S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions
More informationZIERICK MANUFACTURING CORPORATION
ZIERICK MANUFACTURING CORPORATION 131 Radio Circle, Mount Kisco, New York 10549 - (914) 666-2911 - FAX (914) 666-0216 Engineered Interconnection Solutions -Since 1919-3/8-16 THREAD Zierick Printed Circuit
More informationISO6431 STANDARD CYLINDER
SO SNR YLNR standard cylinder series SO-00 ULY R Symbol Material of parts : SO standard type : ouble piston rod type, : djustable type 0 eatures *dentical to SO standard. *igh quality of aluminum tube
More informationHP 2 SERIES Integral Driver - Solid State LED
HP 2 SERIES Installation Instructions Warning High Voltage Hot Surface NEEDED FOR INSTALLATION: By Others 1/8 & 5/32 Allen Wrench Waterproof Wire Connectors Level Phillips Screwdriver IMPORTANT - WEAR
More informationGP-SD GENIE PROBE SMALL DIAMETER
For GENIE PROBE SMALL DIAMETER Installation and Operation Instructions 2 for s Locking Mechanism (if supplied) Set Screws Backed Out To ensure that the is Locking never accidentally loosened or Mechanism
More informationCaution: Installation and Operation Instructions. Locking Mechanism (if supplied) Set Screws Backed Out. Mounting Orientation
Genie Probe Regulator (GPR)/ Genie Probe (GP2)/ Genie Probe for Composite Sampler (CSA)/ And (Model H) Installation and Operation Instructions Caution: Not designed for external fire. Prior to use in a
More informationATV Disc OWNER S MANUAL
ATV Disc OWNER S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result
More informationUniversal flat-panel mount
I N S T A L L A T I O N M A N U A L Universal flat-panel mount www.christiedigital.com PM 2004/ REV 02 Contents - Assembly drawing - Fine tune tilt adjustments - Parts list - Installing the adapter plate
More informationREPAIR INSTRUCTIONS: CABLE
The repair instructions describe replacing the Cable in the Easy Sun PARASOL Sunshade. These repair instructions are intended only for persons with experience of using the tools required. Please read the
More informationSeries JA/JAH/JB. Floating Joint
Floating oint Series A/A/ The floating joint can absorb any "off-centring" or "loss of parallel accuracy" between the cylinder and the driven body. entring is unnecessary. A high level of machining accuracy
More informationPEARL DRUM PEDAL. Instruction Manual
PEARL DRUM PEDAL Instruction Manual Congratulations on your purchase! To get optimum performance of your "P-3002C" Double Pedal, please read this Instruction Manual before playing. Assembly Center Connecting
More informationOPERATING INSTRUCTIONS 5-AXIS CLAMPING SYSTEM + ACCESSORIES
OPERATING INSTRUCTIONS 5-AXIS CLAMPING SYSTEM + ACCESSORIES 1 Contents 1. Introduction 2. Safety instructions and precautions 3 Operating the clamp 3.1 Clamp set up 3.2 Sequence for clamp set up 3.3 Adjusting
More informationPEARL DRUM PEDAL. Instruction Manual
PEARL DRUM PEDAL Instruction Manual Congratulations on your purchase! To get optimum performance of your "P-3002D" Drum Pedal, please read this Instruction Manual before playing. Drive Shaft Assembly Drive
More informationSCREW JACKS Operating Instructions
INS114EN.5 SCREW JACKS Operating Instructions Sweden Int +46 372 265 00 info@swedrive.se Vat.no SE556145631901 138-4551 1 Table of Contents 1. Health and Safety... 3 1.1. Notice about safety... 3 1.2.
More information3400 to 3440 Scarfing Sled Owners Manual Please Read Carefully!
3400 to 3440 Scarfing Sled Owners Manual Please Read Carefully! Parts List: Please identify and verify that you have all of the hardware shown. Please refer to photos in the instructions for the parts
More informationLifeGear G1 /HOME GYM ITEM NO.: 63100
LifeGear G1 /HOME GYM ITEM NO.: 63100 OWNER S MANUAL IMPORTANT: Read all instructions carefully before using this product. Retain this owner s manual for future reference. The specifications of this product
More informationTop spin Nr /
Top spin Nr. 1840 0000 / 1840 1000 Bedienungsanleitung 21-6680 28052014 / A Made in Germany Ideas for dental technology Top spin Nr. 1840 0000 / 1840 1000 Contents 1. Introduction...2 1.1 Symbols...2 2.
More informationW-Pressing Assembly. the top W roller thus creating a uniform and constant pressure between and throughout both top and lower W rollers.
PRODUCT: NUR Fresco HiQ 3200 ISSUE DATE: 10-Sep-02 SOFTWARE AFFECTED: YES NO TYPE OF CHANGE: MANDATORY COST PRODUCTION MAINTENANCE PROJECT MANAGER: SIGNATURE/DATE PART/ASSEMBLY: FCO KIT P/N: 10-0803 W-Pressing
More informationGENERAL OPERATIONAL PRECAUTIONS WARNING! When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following.
More informationFBX1104P FBX1104 FBX1106P FBX1106
FBX1104P FBX1104 FBX1106P FBX1106 Second edition : September 2004 No. 040037 INTRODUCTION Thank you for your purchasing Kansai Special's FBX Series. Read and study this instruction manual carefully before
More informationInstructions for Stone Cutting Machine
Technical data Kg. Instructions for Stone Cutting Machine SCM600 3HP 2800rpm IP55 SCM800 3HP 2800rpm IP55 SCM1000 2800rpm IP55 SCM1200 2800rpm IP55 L=600 B=85(165) L=800 B=85(175) 500x510 0 or 45 600lt/h
More informationJIG CYLINDER. JC series. Features. Without magnet. How to order. With magnet
LN series O00 QLT T eatures aterial of parts *ard anodized aluminum barrel provides corrosion and wear resistance as well as long life. *ompact and space saving. *trict quality control ensures the product
More informationSPIDA SAW OPERATIONS MANUAL
SPIDA SAW OPERATIONS MANUAL CM SERIAL NUMBER. OCTOBER 2000 CONTENTS Page description 1.) Contents 2.) Safety First 3.) CM Overview 4.) CM Specifications 5.) CM Installation 6.) CM Operation Setting the
More informationETX Powered Loudspeaker Accessories
ETX Powered Loudspeaker Accessories ETX-BRKT10, ETX-BRKT12, ETX-BRKT15, ETX-TCA-S, ETX-TCA-L, and ETX-BRKT35 en Installation Guide en 3 Table of contents 1 Safety 4 2 Installation 6 2.1 Wall mount bracket
More informationPEARL DRUM PEDAL. Instruction Manual
PEARL DRUM PEDAL Instruction Manual Congratulations on your purchase! To get optimum performance from your P-932 / P-932L / P-931 Drum Pedal, please read this Instruction Manual before playing. Assembly
More informationOperating Instructions and Parts Manual SLT-1100 Jumbo Scissor Lift Table
Operating Instructions and Parts Manual SLT-1100 Jumbo Scissor Lift Table JET 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-140780 Ph.: 800-274-6848 Revision B1 05/2014 www.jettools.com Copyright
More informationELPMB27. Short Throw Projector Wall Mount Installation Manual xxx(fr) xxx(de) xxx(it) xxx(es) xxx(pt) xxx(zhs)
ELPMB27 Short Throw Projector Wall Mount Installation Manual xxx(fr) xxx(de) xxx(it) xxx(es) xxx(pt) xxx(zhs) Safety Instructions Before using the wall mount, make sure you read all of the safety instructions
More informationFM125 & FM126 Service Guide
FM125 & FM126 Service Guide FM125-0022 & FM125-0024 Repair Kit 1 2 3 4 #1-1 Pc. FM125-5012 Ball Carrier Installation Tool (FM125-0022 Only) #2-2 Pcs. P5-287-R0 O-Ring #3-2 Pcs. P5-067-R2 O-Ring #4-1 Pc.
More informationGENERAL OPERATIONAL PRECAUTIONS PRECAUTIONS ON USING CUT-OFF MACHINE
GENERAL OPERATIONAL PRECAUTIONS WARNING! When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following.
More information8 TONNE LOG SPLITTER
8 TONNE LOG SPLITTER MODEL NO: LOGBUSTER 9 PART NO: 3402043 OPERATION & MAINTENANCE INSTRUCTIONS LS03/16 INTRODUCTION Thank you for purchasing this CLARKE 8 Tonne Log Splitter. Before attempting to use
More informationSETTING UP THE MODEL 210B-2 SRA
SETTING UP THE MODEL 210B-2 SRA SAFETY PRECAUTIONS FOR THE MODEL 210B-2 SRA System Under Pressure: Shut off air supply and disconnect air hose before disassembling or disconnecting parts. Flying Debris:
More informationPLATE LIFTING CLAMPS
LIFTING YOUR USINESS TO HIGHER LEVEL LIFTING YOUR USINESS TO HIGHER LEVEL LIFTING YOUR USINESS TO HIGHER LEVEL PLTE LIFTING LMPS Operational Instruction Manual Universal Plate lamp Model: UP-1 Horizontal
More informationACREAGE SEEDER / PLANTER OWNER S MANUAL
ACREAGE SEEDER / PLANTER OWNER S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions
More informationMaintenance and other important non-personal injury and non-material damage instructions or statements that should be observed.
VIGO INDUSTRIES INSTALLATION GUIDE FOR SHOWER ENCLOSURE ()! SAFETY PRECAUTIONS This Installation Guide uses the following symbols to indicate important information. Always observe the instructions indicated
More informationFifth-wheel coupling JSK 38/50
Repair manual Fifth-wheel coupling JSK 38/5 ZDE 199 3 12 E 6/25 1 LT SK38C-3 English RevA Foreword Table of contents Page Fifth wheel couplings are connecting parts that must comply with very high safety
More informationReliance SG777 Series Steel Water Gage Valves
Installation, Operation, & Maintenance Instructions R500.SG777 10/16/2016 Reliance SG777 Series Steel Water Gage Valves Note: Design variations in Steel Water Gage Valves necessitate typical illustrations,
More informationMODEL T TON HYDRAULIC PRESS INSTRUCTIONS (For Machines Mfd. Since 10/17)
MODEL T1241 20-TON HYDRAULIC PRESS INSTRUCTIONS (For Machines Mfd. Since 10/17) For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com Identification
More informationWind Transmitter compact xx
THE WORLD OF WEATHER DATA - THE WORLD OF WEATHER DATA - THE WORLD OF WEATHER DATA Instruction for Use 021720/03/14 Wind Transmitter compact 4.3519.xx.140... 961 Contents 1 Models... 3 2 Application...
More informationRepair manual. Fifth-wheel coupling JSK 38/50
Repair manual Fifth-wheel coupling JSK 38/5 ZDE 199 3 12 E 6/212 1 Foreword Table of contents Page Fifth wheel couplings are connecting parts that must comply with very high safety requirements and must
More informationFisher 667 Diaphragm Actuators Size 80 and 100
Instruction Manual 667 Size 80 and 100 Actuators Fisher 667 Diaphragm Actuators Size 80 and 100 Contents Introduction... 1 Scope of Manual... 1 Description... 2 Specifications... 2 Maximum Pressure Limitations...
More informationMF-7524 INSTRUCTION MANUAL
MF-7524 INSTRUCTION MANUAL 1 CONTENTS Ⅰ. SPECIFICATIONS...1 Ⅱ. CONFIGURATION OF THE MACHINE COMPONENTS...2 Ⅲ. INSTALLATION... 3 1. Installing the machine head onto the table...3 2. Selecting the motor
More informationTWIN ROD CYLINDERS 6 CONTENTS
CAD drawing data catalog is available. ACTUATORS GENERAL CATALOG TWIN ROD CYLINDERS6 CONTENTS TWIN ROD CYLINDERS 6 Features 745 Specifications/Order Codes 747 Inner Construction and Major Parts 748 Dimensions
More informationWooden Frame Type Instruction Manual
Wooden Frame TypeInstruction Manual Thank you for selecting our product. Before starting installation, please read this manual thoroughly to ensure correct installation. Please keep this manual at hand
More informationSAVE THIS FOR FUTURE REFERENCE THIS PRODUCT IS FOR PROFESSIONAL LABORATORY USE ONLY USER'S MANUAL
DENTAL, INC. TECHNICAL BULLETIN G801-022510 5860 FLYNN CREEK ROAD READ ALL INSTRUCTIONS P.O. BOX 106 BEFORE PROCEEDING COMPTCHE, CALIFORNIA, U.S.A. 95427-0106 SAVE THIS FOR FUTURE REFERENCE www.wellsdental.com
More informationModel Numbers: P/N Date TPS-200 POLE SAW ATT TPS-200. Supplier To The Outdoor Power Equipment Industry
Model Numbers: TPS-200 POLE SAW ATT TTACHMENT P/N 28577 Date 05-04-01 TPS-200 Supplier To The Outdoor Power Equipment Industry 1. Introduction It is important that you read and understand your TANAKA brush
More informationMaintenance Information
16601023 Edition 2 January 2014 Air Impact Wrench 2705P1 Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these
More informationSection 1: Parts List. Section 2: Additional Considerations
Section 1: Parts List Page 1 of 6 Qty Description 1 Replacement Hydraulic Pump 1 Pump Puller Fitting, Large 1 Pump Puller Fitting, Small 1 5/16 Allen Key 1 Section 2: Additional Considerations WARNING
More informationEMO. Service Instruction. created by Frank Weithöner. Table of contents: Special Tools Assembling Mixing Chamber
EMO Service Instruction created by Frank Weithöner Table of contents: - Special Tools Disassembling Mixing Chamber Assembling Mixing Chamber Adjustment Rotor / Level Indicator Unit Temperature Compensating
More informationM4 Foot Operated Underpinner Instruction Manual
M4 Foot Operated Underpinner Instruction Manual M4 Walker Rd, Bardon Hill, Coalville, Leicestershire LE67 1TU, England Tel. +44 (0)130 1692, Fax +44 (0)130 16929 e mail sales@framerscorner.co.uk M4 Underpinner
More informationPlease read and understand the OnBoard Timpani Cart Owner s Manual before using the Timpani Cart.
Assembly and Owner s Manual OnBoard Timpani Cart Performance Position Towing Position CONTENTS Important User Information...........................2 General......................................2 Manufacturer.................................2
More informationAdjusting 45 Compass Hardware Including 4-Point
Adjusting 45 Compass Hardware Including 4-Point Compass Hardware - US Patent No. 7,104,610 & 7,891,739 Apparatus for Mounting a Wheelchair Back Quick Release Fixed 4-Point The information in this manual
More informationEMB Manufacturing Inc Boomer Line St. Clements, On N0B 2M0 Canada Ph: (519) Fax: (519) P200
BY EMB MFG INC. EMB Manufacturing Inc. 4144 Boomer Line St. Clements, On N0B 2M0 Canada Ph: (519) 699-9283 Fax: (519) 699-4146 www.embmfg.com P200 Pivoting Chainsaw Holder Accessory Installation Instructions
More informationCONTENTS PRECAUTIONS BEFORE STARTING OPERATION PREPARATION FOR OPERATION CAUTIONS ON USE OPERATION
CONTENTS PRECAUTIONS BEFORE STARTING OPERATION ------------------------------------- 1 PREPARATION FOR OPERATION 1. Adjustment of needle bar stop position ---------------------------------------------------------
More informationSolenoid valve for high vacuum. Orifice: 1, 2, 3, 4.5, 6. NC (normally closed) type. Cv flow factor (*4) Working pressure range Pa (abs)
V 1 V 1 Series Orifice: 1,,,., N (normally closed) type IS symbol N (normally closed) type ommon specifications escriptions Working fluid Withstanding pressure MPa luid temperature mbient temperature eat
More informationINSTRUCTION BX1425P,PSM,PTV BX1433P,PSM,PTV BX1025P,PSM BX1033P,PSM. No First published : November 1997
INSTRUCTION Industrial Sewing Machines BX1425P,PSM,PTV BX1433P,PSM,PTV BX1025P,PSM BX1033P,PSM First published : November 1997 No. 970112 INTRODUCTION Thank you for your purchasing Kansai Special's BX
More informationINSTRUCTION MANUAL Q-HYDRAULIC
Dat: 15.04.02 No: 94-BA 5039E/1b TABLE OF CONTENTS Part III 3.0 Type code explanation 3.1 Service connections 3.2 Impeller clearance adjustment 3.2.1 Wear of wearing parts 3.2.2 General notes to adjustment
More informationVARIABLE SPEED WOOD LATHE
MODEL MC1100B VARIABLE SPEED WOOD LATHE INSTRUCTION MANUAL Please read and fully understand the instructions in this manual before operation. Keep this manual safe for future reference. Version: 2015.02.02
More informationFrameless Inline Door QCI5248
INSTALLATION INSTRUCTIONS Frameless Inline Door QCI5248 FRAMELESS PANEL / DOOR / PANEL QCI5248 REV. 0 Page 1 Certified 06/16/2016 Parts List with glass to glass hinges *Quantities may vary. **Support Bar
More informationMechanical Frappe Press
Mechanical Frappe Press Operation Manual CONTENTS OPERATIONAL INSTRUCTIONS PRECAUTIONS PART NAMES INCLUDED ITEMS BASIC OPERATION MAINTENANCE REPLACEMENT PARTS Thank you for using The Frapptastic Five Mechanical
More informationFrameless Inline Door With Return QCI5263
INSTALLATION INSTRUCTIONS Frameless Inline Door With Return QCI5263 WALL MOUNT HINGES FRAMELESS DOOR / PANEL / RETURN PANEL QCI5263 REV. 0 Page 1 Certified 06/17/2016 Parts List with wall mount hinges
More informationSide Winder R o u t e r L i f t.
Woodpeckers PRECISION WOODWORKING TOOLS Side Winder R o u t e r L i f t. INSTALLATION INSTRUCTIONS The wrench handle must be pointing left in order to fully insert or remove it. Lift Wrench Once fully
More informationEKX Full-Range Loudspeaker Accessories
EKX Full-Range Loudspeaker Accessories EKX-BRKT12, EKX-BRKT15, and EKX-TCA en Installation Note en 3 Table of contents 1 Safety 4 1.1 Safety point 6 2 Installation 7 2.1 Wall mount bracket 7 2.2 Truss
More informationInstallation Guide. English. English
Installation Guide Safety Instructions For your safety, read all the instructions in this guide before using the setting plate. Incorrect handling that ignores instructions in this guide could damage the
More informationSAM. Model: STV-C65 LCD Mobile Visualized Stand Instruction Manual. Weight Capacity: 1251bs / 56.7kg Suits LCD Flat Panel Display: 42"-55" Page 20
SAM Model: STV-C65 LCD Mobile Visualized Stand Instruction Manual Weight Capacity: 1251bs / 56.7kg Suits LCD Flat Panel Display: 42"-55" 20 Step 6 LCD Mobile Lift Stand Model: STV-C65 Cable management
More informationPURESTREAM SYSTEM - ASSEMBLY GUIDE
PURESTREAM SYSTEM - ASSEMBLY GUIDE VISIT OUR WEBSITE : www.cagpurification.com our installment procedure videos in the PURESTREAM Piping section. NECESSARY TOOLS FOR INSTALLATION We suggest the use of
More informationTH450A-T TH550A-T THP550-T/TS3000
0 TH450A-T TH550A-T THP550-T/TS3000 INSTRUCTION MANUAL CEILING TYPE (OVERHEAD TRAVELING TYPE) INDUSTRIAL ROBOT SPECIFICATIONS Notice 1. Make sure that this instruction manual is delivered to the final
More informationMast and Antennas for Field Day & Emergencies
Mast and Antennas for Field Day & Emergencies John A. Allocca, WB2LUA, July 2005 This is a 27 feet 1.5 diameter portable guyed mast with a 28 feet diameter footprint. It breaks down into four 6 feet sections
More informationGared Pro-S Portable Backstop
Models: 9616 & 9618 Installation, Operation and Maintenance Instructions Please read all instructions before attempting installation or operation of these units SAVE THESE INSTRUCTIONS FOR FUTURE USE PUBLICATION
More informationHorizontal Cable Systems
ALUMINUM RAILING INSTALLATION INSTRUCTIONS v2012 orizontal Cable Systems 1) Check Contents Of Packages: Verify that all parts have arrived and that they match the packing list. 1A) Coastal applications:
More informationassembly instructions
door opens outwards door opens inwards front cubicle door opens outwards or inwards with side panel seite 1 ensure that the supplied parts are complete by checking the packing list. make sure that tools
More informationMounting instructions SZ210 Full-frame pedestal with screw-on tube with placement hinge, for type SCHATTELLO
This height will be made to order. Mounting instructions SZ210 Full-frame pedestal with screw-on tube with placement hinge, for type SCHATTELLO The following instructions include all information necessary
More informationYoke Type Hinged Closures Installation, Operation & Maintenance
2612 Howard Street BULLETIN TT1328 Louisville, KY 40211 USA Revised Jan 2010 Phone 502-774-6011 Fax 502-774-6300 Website: www.sypris.com/tubeturns E-mail: tubeturns@sypristechnologies.com Yoke Type Hinged
More informationOPERATION & MAINTENANCE INSTRUCTIONS
FOOT OPERATED 1.5 TONNE LOG SPLITTER MODEL NO: LOGBUSTER 10 PART NO: 3402046 OPERATION & MAINTENANCE INSTRUCTIONS LS0815 INTRODUCTION Thank you for purchasing this CLARKE Foot Operated 1.5 Tonne Log Splitter.
More informationinstallation guide
JANUS INTERNATIONAL 1 866 562 2580 w w w. j a n u s i n t l. c o m 2000 2500 3000 installation guide RIGHT DRIVE END SHOWN LH OPPOSITE LEFT TENSION END SHOWN RH OPPOSITE PUSH-UP OPERATION 2000 2500 3000
More informationTapping Screw (W/Flange) 46 Cord Armor 47 Tube (D) 48 Cord. 45 Cord Clip. Tapping Screw (W/Flange) 10 Gear Cover Ass'y. 12 Socket (B) Ass'y
W8VB The exploded assembly drawing should be used only for authoized service center. W8VB Item No. Part time 1 Magnetic Hex. Socket 2 Sub Stopper 3 O-Ring (S-16) 4 Locator (A) 5 Lock Sleeve (A) 6 O-Ring
More informationINSTALLATION GUIDE Ceiling TV Mount MHP-52
ISTLLTIO GUIDE Ceiling TV Mount MHP-52 Max Load Capacity: 125 lbs (57kg) ote: Read entire instruction sheet before you start installation and assembly. Be sure to read this entire manual thoroughly and
More informationAssembly instructions for the swivel castor kit
Assembly instructions for the swivel castor kit Thank you very much for choosing a Sport-Thieme product. Please read the instructions fully before you assemble the equipment so you can enjoy the product
More informationABSL Model Background Stand
ABSL Model Background Stand Product Overview: The Ravelli ABSL model background stand is adjustable up to 13' tall by 15' wide. It is comprised of two tripod stands and five 3 cross bar sections and includes
More informationPrecision Chucks for Improved Accuracy and Increased Productivity
Precision Workholding Technology Precision Chucks for Improved Accuracy and Increased Productivity Precision Air Chucks (Self Contained Design) MicroCentric Precision Air Chucks feature a patented open
More informationTRAKFAST REPAIR MANUAL DANGER TOOL DISASSEMBLY ALWAYS TAKE THE FOLLOWING PRECAUTIONS BEFORE ANY SERVICE OR ROUTING MAINTENANCE IS PERFORMED:
DANGER ALWAYS TAKE THE FOLLOWING PRECAUTIONS BEFORE ANY SERVICE OR ROUTING MAINTENANCE IS PERFORMED: REMOVE FASTENERS REMOVE FUEL CELL REMOVE BATTERY REMOVE THE MAGAZINE ASSEMBLY Loosen and remove knob
More informationHandle Length (in.) Ultimate Load (lbs.) Weight Each (lbs.)
L-150 Lever Type Binder Lebus Binders Extra heavy construction at leverage point to prevent spreading. Heel of binder toggles away from load, permitting easy release. Ball and socket swivel joints at hook
More informationAngle Grinder MODEL 9553B MODEL 9555B
ENGLISH Angle Grinder MODEL 9553B MODEL 9555B 006649 DOUBLE INSULATION I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR
More informationKD Table Base Assembly and Top Attachment Instructions
KD Table Base Assembly and Top Attachment Instructions 4011xx 5000xx 7014xx 8001xx 8206xx Congratulations on the purchase of your Tropitone furniture. Read through all steps before starting assembly. CAUTION:
More informationINSTALLATION MANUAL H A
INSTALLATION MANUAL CABINET RACK CR-43-6 (4-UNIT SIZE) Be sure to read this installation manual thoroughly before installing this Cabinet Rack. For the mounting procedures of the components and the relevant
More informationset of safety brace steel cable draw-up gate kpl
0324101 7108020 8208100 Order-nr. Description Number 0324101 safety brace steel cable draw-up gate 2 7108020 hexagon-head tap bolt M8x20 galv. 2 8208100 hexagon nut M8 galv. 2 set of safety brace steel
More information1500HD Assembly & Operation Manual 1500 lb. Capacity Motorcycle Lift
1500HD Assembly & Operation Manual 1500 lb. Capacity Motorcycle Lift 1500HD Assembly Instructions Assembly 1. Remove the lift and all parts from the wooden crate 2. Remove the pump from the cardboard box
More informationInstruction manual SUN-PM100L. SUN-PM100L Polishing Machine English
Instruction manual SUN-PM100L SUN-PM100L Polishing Machine English Table: SUN-UM-TL-PM001 Version: A/0 Fiber Optic Solutions Provider Ⅰ Safety Precautions To ensure safe operation and maximize product
More informationHD installation guide
JANUS INTERNATIONAL 1 866 562 2580 www.janusintl.c o m 1950 1950HD installation guide RIGHT DRIVE END SHOWN LH OPPOSITE LEFT TENSION END SHOWN RH OPPOSITE PUSH-UP OPERATION 1950 1950HD SHOWN A rolling
More informationATV CULTIVATOR OWNER S MANUAL
ATV CULTIVATOR OWNER S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may
More informationModel POA-CHB-XL50. Assembly and Installation Manual. Projector Bracket. Contents. Be sure to consult with a qualified installation specialist
Assembly and Installation Manual Projector Bracket Model POA-CHB-XL50 Be sure to consult with a qualified installation specialist This bracket is specifically for use with our projector. Be especially
More informationSERVICE PARTS LIST PAGE 1 OF 6 BASE ASSEMBLY SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 12" SLIDING COMPOUND MITER SAW
PAGE 1 OF 6 BASE ASSEMBLY 00 0 CATALOG NO. EXAMPLE: SPECIFY CATALOG NO. AND NO. WHEN ORDERING PARTS 6955-20 1 02-80-0050 Thrust Bearing (1) 2 05-80-0510 M5 x 12mm Flat Head T-20 Screw (5) 3 05-81-0135
More informationHANDLING AND ASSEMBLY INSTRUCTIONS FOR TRUE FOCUS 3.0M, 3.8M AND 4.2M ANTENNAS WITH POLAR MOUNT
HANDLING AND ASSEMBLY INSTRUCTIONS FOR TRUE FOCUS 3.0M, 3.8M AND 4.2M ANTENNAS WITH POLAR MOUNT Introduction SECTION 1 Thank you for purchasing one of our fine True Focus products. This manual covers the
More informationBasic Assembly For Conventional Series 9000 Structural Panels
Steelcase, Inc. Grand Rapids, MI 49501 U.S.A. 1-888-783-3522 Basic Assembly For Conventional Series 9000 Structural Panels NOTE: Assembly directions for curved panels are the same as standard panels. Tools
More informationIndustrial Drill Chucks with Key. For Stationary Machines and Portable Drilling Machines. Diameter (mm)
Drilling Industrial Drill Chucks with Key For Stationary Machines and Portable Drilling Machines Specifically designed for stationary drilling, turning, milling and wood working machines The one-piece
More informationHip Roof Canopy Instructions
Hip Roof Canopy Instructions - PUT SAFETY FIRST. NOT COMPLYING WITH THE PROCEDURES AND PRECAUTIONS OUTLINED IN THIS MANUAL MAY RESULT IN PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.. Before attempting
More information