Bracket Assembly and Installation Manual

Transcription

1 Bracket Assembly and Installation Manual Model POA-CHB-DWL2500 Contents Installation Precautions Parts list Attach the Projector bracket to the projector Attach the drop-prevention wire to the projector Attach the projector to the ceiling bracket How to adjust the projection angle Dimensions Approximate projection distance Be sure to consult with a qualified installation specialist. The diagram shows the ceiling bracket for low ceilings by way of example. This product is used together with the products listed below. It cannot be used together with any products other than those listed below. POA-CH-EX03A (Wall hanging bracket)+poa-chs-ps02 (Low-ceiling Bracket) POA-CHS-PS02 (Low-ceiling Bracket) POA-CHL-PL02 (High-ceiling Bracket) This bracket is only for use with Sanyo projectors. Do not use for any other equipment or purposes. Be especially careful that children do not hang from it. Perform proper assembly and installation by following these instructions. Be sure to follow all precautions. Installation Precautions When hanging a projector from the ceiling using this bracket (hereinafter called the projector bracket ), the ceiling must have adequate strength to support the projector, the ceiling bracket and the projector bracket. Furthermore, if installing to a wall, the wall must have enough strength to support the combined weight of the projector, the wall mount bracket, the ceiling mount bracket and this projector bracket. Before installation, check the combined weight of the projector, ceiling mount bracket and wall mount bracket (if installing to a wall) and this projector bracket as well as the strength of the ceiling or wall based on that weight. If the strength is insufficient, provide adequate reinforcement before proceeding. Always install to a level ceiling. Never install to an inclined ceiling. During installation, take appropriate measures to prevent lateral swaying due to earthquakes or vibration (using wires, etc.). The total weight of the projector bracket is 4.0 kg.

2 Parts list Drop-prevention wires...2 Fastening plates...2 Assembly and Installation Manual (this manual) Projector bracket...1 Screws A...4 M4 x 10mm (Phillips head machine screw with integrated spring washer and flat washer) Screws B...5 M4 x 18mm (Phillips head machine screw with integrated spring washer and flat washer) Screws C...4 M6 x 14mm (Phillips head hex bolt with integrated spring washer and flat washer) Screws D...4 M3 x 8mm (Phillips head machine screw with integrated spring washer) Attach the Projector bracket to the Projector Turn over the projector and use the included Screws B (x5) to attach the Projector bracket. Screws B (included)... 5 Projector bracket 2

3 Attach the drop-prevention wire to the Projector To prevent the projector from falling down, use the included drop-prevention wires to connect the projector and the projector mount bracket. (2 locations) q Adjuster Preventing the projector from falling: Be sure to follow these instructions to keep the projector from falling. q Installing to the adjusters w Theft-prevention wire installation bar w Installing to the theft-prevention wire installation bar Adjuster Drop-prevention wire (included) Drop-prevention wire (included) Theft-prevention wire installation bar 1. Lift up the adjuster of the projector, and then wind the included drop-prevention wire around it as shown in the illustration. 1. Wind the included drop-prevention wire around the theft-prevention wire installation bar as shown in the illustration. Wind around two more times. Wind around one more time. 2. Wind the drop-prevention wire around the adjuster two more times. 2. Wind the drop-prevention wire around the bar one more time. Screws A (included)... 2 Screws A (included) Attach the drop-prevention wire to the projector bracket with the two included screws A, and then lower the adjuster. 3. Attach the drop-prevention wire to the projector bracket with the two included screws A. 3

4 Attach the projector to the ceiling bracket q Install by sliding the projector bracket with the projector installed into the ceiling mount bracket (sold separately) which is secured to the ceiling or to the wall mount bracket (sold separately). Be careful not to drop the projector while this process. Although the projector is supported, it is not secured in place. Ceiling bracket Projector bracket w Use the included Screws C (x4), fastening plates, Screws D (x4) to secure the projector bracket to the ceiling bracket (sold separately). Screws C (included)... 2 Screws D (included)... 2 Fastening plates (included) Fastening plates (included) Screws D (included)... 2 Screws C (included) High-ceiling Bracket : POA-CHL-PL02 Low-ceiling Bracket : POA-CHS-PS02 The diagram shows the low-ceiling bracket by way of example.

5 How to adjust the projection angle Before adjusting: Read the projector instruction manual carefully, turn on the power, and project an image. Loosen the slide mechanism fixing screws, and then move the ceiling mount bracket forward or back to provisionally determine the projection size. Then retighten the slide mechanism fixing screws and adjust the angle. Loosen the angle adjustment nut using the wrench included with the ceiling bracket (sold separately) and align the projector to project the image in the center of the screen. Then fasten the nut securely. Angle adjustment nut Turns left and right 360 Slide mechanism fixing screws Wrench If using a commercially-available wrench, use one with a size of 24mm. Slides forward and back 170 mm 15 horizontal tilt Slide mechanism fixing screws 15 horizontal tilt High-ceiling Bracket : POA-CHL-PL02 Low-ceiling Bracket : POA-CHS-PS02 The diagram shows the low-ceiling bracket by way of example. Caution After securing the projector angle, if the angle is readjusted without loosening the screw, the fastening area could be deformed, which could prevent it from being tightened again. When readjusting the angle, loosen the angle adjustment nut before adjusting the angle. If the adjustment is off center, readjust the angle. After making the adjustment, be sure the screw is securely tightened. 5

6 Dimensions When using the high-ceiling bracket (Used together with POA-CHL-PL02 and POA-CHB-DWL2500) A length shows distance from ceiling to lower side of projector when suspended from ceiling. Min A length Center of lens 77.5 When using the low-ceiling bracket (Used together with POA-CHS-PS02 and POA-CHB-DWL2500) Center of lens When using the wall hanging bracket (Used together with POA-CH-EX03A, POA-CHS-PS02 and POA-CHB-DWL2500) (Height adjustable) A length Center of lens

7 Approximate projection distance (1) (When using projector: PDG-DWL2500 or PDG-DXL2000) When using the high-ceiling bracket (Used together with POA-CHL-PL02 and POA-CHB-DWL2500) X(mm) 233 PDG-DWL (16:10) 90 (16:10) 100 (16:10) 110 (16:10) A length+87 A length+107 A length+127 A length+147 PDG-DXL (4:3) 80 (4:3) 90 (4:3) A length+115 A length+141 A length+168 Y(mm) A length * Height values are intended as a guide only. The screen sizes may vary depending on the content of the projected images, so use the slide mechanism to adjust the position. Slide mechanism fixing screws Sliding width 170mm When using the low-ceiling bracket (Used together with POA-CHS-PS02 and POA-CHB-DWL2500) X(mm) 233 PDG-DWL (16:10) 90 (16:10) 100 (16:10) 110 (16:10) PDG-DXL2000 Y(mm) 70 (4:3) 80 (4:3) 90 (4:3) Slide mechanism fixing screws Sliding width 170mm 7

8 Approximate projection distance (2) (When using projector: PDG-DWL2500 or PDG-DXL2000) When using the wall hanging bracket (Used together with POA-CH-EX03A, POA-CHS-PS02 and POA-CHB-DWL2500) PDG-DWL2500 X(mm) 80 (16:10) 90 (16:10) 100 (16:10) 110 (16:10) PDG-DXL (4:3) 80 (4:3) 90 (4:3) * Distance Y can be adjusted to a height of 25.8 mm with the POA-CH-EX03A (sold separately). Refer to the assembly and installation manual for the POA-CH-EX03A (sold separately) for details on the adjustment method. * Height values are intended as a guide only. The screen sizes may vary depending on the content of the projected images, so use the slide mechanism to adjust the position. Y(mm) (When height adjusted to the minimum) Slide mechanism fixing screws Sliding width 170mm Caution Check that the slide mechanism fixing screws are fully tightened even when not using the sliding mechanism. 8