MUTO COMFORT DORMOTION XL 150/80 L 80

Transcription

1 MUTO COMFORT DORMOTION XL 150/80 L 80 Installation instructions - Wall mount with DORMOTION ( )

2 TABLE OF CONTENTS Closer overall Overview Intended use Wall requirements and fittings Safety instructions Symbols used - safety/ installation Maintenance, care, repair Disposal 3 Specifications Technical data 3 INSTALLATION INSTRUCTIONS Overall view 4 Securing wood adaptor 5 Securing track to mounting surface 6 Single mount Double mount 7 Installing the roller carriers 8 ANTI-JUMP: Disengaging the anti-jump 9 Engaging the anti-jump 11 DORMOTION Unit: Installing DORMOTION 8 Installing DORMOTION start/stops 13 END STOPS: Installing end stops 9 Adjustment end stop location: LEADING end stop Adjustment end stop location: TRAILING end stop 12 FLOOR GUIDE: Installing floor guide 10 Install /rollers in track 10 Installing cover clips Installing brush profile 14 Installing cover Installing end caps 15 ADJUSTMENTS: Adjustment height 11 Adjustment end stop location: LEADING end stop Adjustment end stop location: TRAILING end stop 12 DORMA USA, Inc. Dorma Drive, Drawer AC Toll-Free: dormaarchitectural@dorma. com

3 Overview These instructions are for installation of the MUTO COMFORT sliding system XL150/80 and L80 for the following mounting and style versions: 1. Wall mounting Intended use - for sliding s in dry in areas only - for manual slow opening and closing only Wall requirements and fittings - The substructure/wall must be able to bear permanent loads, be level and perpendicular (max. tolerance: 1/16" (2 mm) per meter). - Fixings must be sufficiently dimensioned for the substructure/ wall and weight of the. Safety instructions - Installation requires two people - Always wear protective clothing Symbols used Safety/Installation Caution! Mounting components must meet the requirements of substructure/wall and weight. Please read the technical information for fittings. Information note Always use silicone- and oil-free cleaners (e.g. acetone). Closing edge Maintenance, care, repair - immediately replace damaged parts - always use original DORMA parts - use a damp cloth for occasional cleaning, especially the track Disposal Dispose in accordance with local, state and national regulations. Specifications Technical data Single Door Double Door XL150 XL80 L80 XL150 XL80 L80 Max. leaf width inches [mm] 60" [1524] 60" [1524] 60" [1524] 2x 60" [2x 1524] 2x 60" [2x 1524] 2x 60" [2x 1524] Min. leaf width inches [mm] 40-1/8" [1020] 31-7/8" [810] 39" [990] 2x 40-1/8" [2x 1020] 2x 31-7/8" [2x 810] 2x 39" [2x 990] Wall Mount Max. leaf height inches [M] 118" [3M] 118" [3M] 118" [3M] 118" [3M] 118" [3M] 118" [3M] Door leaf thickness inches [mm] 1-3/8" /32" [35-50] 1-3/8" /32" [35-50] 1-3/8" /32" [35-50] 1-3/8" /32" [35-50] 1-3/8" /32" [35-50] 1-3/8" /32" [35-50] Door leaf weight lbs [kg] <330lbs [<150] <176lbs [< 80] <176lbs [<80] 2x <330lbs [2x <150] 2x <176lbs [2x <80] 2x <176lbs [2x <80] 3

4 INSTALLATION INSTRUCTIONS Overall view System includes the following components: 1. Cover panel 2. Brush strip 3. Track 4. End cap 5. End stop 6. Cover clips 7. Start/stop guides 8. Roller carrier 9. adaptor 10. Floor guide 11. Dormotion unit 4 4

5 Securing wood adaptor L80 L80 First 4 holes Last 4 holes adaptor Every 4th hole Every 4th hole Every 4th hole Every 4th hole 3/8" [10mm] XL150/80 XL150/80 adaptor Every 4th hole Every 4th hole Every 4th hole Every 4th hole 1 1/2" [13mm] NOTE: Top of must be reinforced to secure wood adapter. 1.1 Prepare the properly for the wood adaptor. NOTE: Seal top and bottom of to minimize warping (use wood manufacturer's recommendations). 1.2 Cut wood adapter to be equal width of. 1.3 XL150/80 and L80: Secure the two wood adaptor pieces to top of wood with #10 x 3" wood screws. NOTE: Be sure screws are always secured in the first four and last four holes of the adaptor, along with every fourth hole in between. NOTE: Be sure screws are always secured in the first four and last four holes of the adaptor, along with every four hole in between. 5

6 Securing track to mounting surface Ensure the track is properly level and secure it to the wall per the appropriate measurements on the prior page. 2.2 Use appropriate fasteners according to the following recommendations. NOTE: SEE DIMENSION INSTRUCTIONS ON NEXT PAGE FOR REFERENCE. NOTE: WALL REINFORCEMENT: The wall reinforcement must be a minimum of ¼ (6mm) x 3 (76mm) steel angle, 16 gauge metal stud, or 1 1/2 (38mm) thick wood blocking secured to the wall studs on a maximum 16 (406mm) centers for the length of the track. The wall reinforcement may be flush on the wall surface or on the interior of the wall. For masonry walls the track may be secured directly to the wall with lead anchors. Track mounting screws must fully penetrate the steel angle, metal stud, or wood blocking, utilizing the predrilled holes in the MUTO track. Consult with a structural engineer to determine if reinforcement is adequate for your specific application or to meet specific codes in your location. 6

7 Single mount Track length = 2 x DW Top of track to center of mounting hole in track 15/16" [24mm] Y DW clear opening height (CH) DH TH = DH + X 1-3/16" [30mm] clear opening height (CH) 1-3/16" [30mm] clear opening width (CW) Bottom of to floor 3/8" [10mm] DH (XL) height clear opening height + Y - 11/16" [18mm] DH (L) height clear opening height + Y - 1/2" [13mm] Y Top of clear opening to bottom of track TH Floor to top of track DW width clear opening width + 2-3/8" [60mm] XL150/L80 L80 X 1-7/8" [47mm] 1-9/16" [47mm] Double mount Overall track length = D1TL + D2TL Door1 Track length (D1TL) = 2 x DW Door2 Track length (D2TL) = 2 x DW Top of track to center of mounting hole in track 15/16" [24mm] Y clear opening width (CW) clear opening height (CH) DH TH = DH + X DW DW 1-3/16" [30mm] 1/4" [6mm] clear opening height (CH) 1-3/16" [30mm] DH (XL) height clear opening height + Y - 11/16" [18mm] DH (L) height clear opening height + Y - 1/2" [13mm] Y TH Top of clear opening to bottom of track Floor to top of track Bottom of to floor 3/8" [10mm] DW width clear opening width + 2-3/8" [60mm] XL150/L80 L80 X 1-7/8" [47mm] 1-9/16" [47mm] 7

8 Installing the roller carriers Z Secure DETERMINE THE LEADING (X) VERSUS TRAILING (Z) EDGE OF THE DOOR. LEADING IS SIDE CLOSEST TO LATCH (CLOSED). Roller location on wood with DORMOTION unit XL150/80 L80 Single X 3-1/8" [80] 3-1/8" [80] Double X 1-9/16" [40] 1-9/16" [40] Single Z 1-9/16" [40] 1-9/16" [40] Double Z 2-3/8" [60] 2-3/8" [60] Roller carrier X Legend: Closing edge of. Torque value: XL150/80 / L80 = 10ft lbs [14Nm] 3 (Front of) (Front of) XL150/80 = 4mm L80 = 2.5mm NOTE: FULLY CLEAN SURFACE OF WOOD DOOR ADAPTOR. DISCARD GASKET. 3.1 Slide roller carriers onto wood adaptor. 3.2 Secure roller carriers to wood adaptor using appropriate-size hex key at 10ft lbs (14 Nm). Installing DORMOTION DORMOTION dampener Triggers XL150 adaptor Roller carrier XL80 Triggers engaged 4 DORMOTION dampener flush against LEADING roller carrier XL150/80 = 4mm L80 = 2.5mm 4.1 Slide DORMOTION dampener onto wood adaptor. NOTE: Oriented with triggers facing outward. 4.2 Dampener must be flush against leading roller carrier. NOTE: Leading carrier is on side of closest to latch. 4.3 Secure dampener to wood adaptor using appropriate-size hex key. 4.4 Engage triggers: push out towards end of DORMOTION unit. 8

9 Disengaging the anti-jump Antijump 5 Antijump NOTE: Anti-jump shipped engaged. Anti-jump adjustment screw XL150/80 = 4mm L80 = 2.5mm 5.1 Disengage the anti-jump on roller carrier. NOTE: Using an appropriate-size hex key, push anti-jump adjustment screw IN and turn COUNTER-CLOCKWISE to disengage anti-jump. Installing the end stops Set screw Track XL150/80 = 3mm L80 = 2mm 6 End stops Bottom section of end stop 6.1 Slide end stops into each end of track. NOTE: Loosen bottom section of end stop for easier install. NOTE: FOR XL150 end stops, be sure set screw is flush with back of bumper. NOTE: Exact location/adjustments will be determined in step 11. 9

10 Install /rollers in track 7 ENSURE ROLLERS AND TRACK ARE FREE OF DEBRIS. 7.1 Tip wood and rollers upward and rest rollers on track. Install floor guide Wall 5/16" [7mm] = = Floor guide Floor guide 1-1/4" [32mm] Temporarily slide floor guide into bottom groove of wood. 8.2 Be sure wood is plumb. 8.3 Mark appropriate floor guide measurements, and remove wood and rollers from track. 8.4 Pre-drill into mounting surface using a 5/16" drill bit. 8.5 Secure floor guide with included fasteners. 8.6 Set wood and rollers back onto track. 10

11 Adjustment height +3/16"[5] -3/16" [5] Door height adjustment tolerance XL150/80 L80 Height adjustment screw 5/16" [7mm] +3/16" [+5] -3/16" [-5] +3/16" [+5] -3/16" [-5] Floor guide 9 = = 3/8" [10mm] XL150/80 torque 10 ft lbs [14 Nm] L80 torque 5 ft lbs [6 Nm] Height adjustment locking screws XL150/80 = 4mm L80 = 2.5mm 9.1 Set height of wood. 9.2 Using appropriate-size hex key, loosen height adjustment locking screws of carrier. 9.3 Using appropriate-size hex key, turn height adjustment screw CLOCKWISE or COUNTER-CLOCKWISE to raise or lower glass. NOTE: Be sure wood is level during this adjustment. Engaging the anti-jump Antijump 10 Antijump Anti-jump adjustment screw XL150/80 = 4mm L80 = 2.5mm 10.1 Engage anti-jump on roller carrier. NOTE: Using appropriate-size hex key, push anti-jump adjustment screw IN and turn CLOCKWISE to engage antijump. 11

12 Adjustment end stop location: LEADING end stop 0mm END STOP LOCATION: LEADING EDGE XL150/80 = 3mm L80 = 2mm NOTE: Pair of s: Be sure there is a 1/4" [6mm] gap between the two s. End stop Bumper Door overlap of frame max. 1-3/16" [30mm] Edge of roller carrier Door closed Set end stop locations: 11.1 Slide end stop desired location on track. Bumper should touch edge of roller carrier. edge Frame edge Handle LOCATION OF WOOD DOOR TO FRAME EDGE. XL150/80 torque Secure L80 torque Bumper min. 1" [25mm] Handle to frame edge distance. *Verify with local jurisdiction.* 3 ft lbs [4 Nm] 2.5 ft lbs [3 Nm] Adjustment end stop location: TRAILING end stop Edge of roller carrier 0mm Bumper END STOP LOCATION: TRAILING EDGE End stop Door opened XL150/80 = 3mm L80 = 2mm NOTE: Pair of s: Be sure there is a 1/4" [6mm] gap between the two s. Set end stop locations: 11.1 Slide end stop desired location on track. Bumper should touch edge of roller carrier. Handle Bumper 11 edge Frame edge LOCATION OF WOOD DOOR TO FRAME EDGE. min. 1" [25mm] Handle to frame edge distance. *Verify with local jurisdiction.* XL150/80 torque 3 ft lbs [4 Nm] Secure L80 torque 2.5 ft lbs [3 Nm] 12

13 Install DORMOTION start/stops Slide triggers in toward middle of Dormotion unit. Triggers CLOSING SIDE Slide triggers in toward middle of Dormotion unit. Legend: Closing edge of. 0mm 12.3 Slide all the way CLOSED Carrier should touch end stop Slide start/stop into Dormotion trigger Rotate plates inside track to engage Tighten screws using appropriate-size hex key. End stop Bumper Edge of roller carrier start/stop OPENING SIDE 0mm 12.3 Slide all the way OPEN Tighten screws using 12.4 Carrier should touch end stop. appropriate-size hex 12.5 Slide start/stop into Dormotion trigger. key Rotate plates inside track to engage. Edge of roller carrier Bumper End stop start/stop Plates parallel Plates parallel Start/stop locations Rotate in track XL150/80 = 4mm L80 = 2mm Set screw End stop Start/ stop Roller Start/ stop DORMOTION UNIT Roller End stop Loosen screws on plates. NOTE: Plates should start out parallel to track Place start/stop into track channel (SEE STEPS INSIDE IMAGE ABOVE.) 13

14 Install cover clips Cover clip Insert cover clips into track. (One clip per foot) 13.2 Insert perpendicular to track, and turn CLOCKWISE to snap into place. Install brush profile Cover Brush Measure and cut brush to appropriate length Slide brush into cover. 14

15 Install cover Cover clip Cover 15 Cover 15.1 Secure cover to clips and snap into place. NOTE: Roll cover from the bottom upwards. NOTE: Ensure the bottom of the cover is supported by the groove in the cover clip. Install end caps End cap End cap Snap end caps onto track. 15

16 DORMA USA, INC. DORMA DRIVE, DRAWER AC REAMSTOWN, PA TOLL-FREE: FAX: /2016, Subject to change without notice