MUELLER
|
|
- Herbert Fisher
- 6 years ago
- Views:
Transcription
1 Slab Mounted: 24x24 Backyard Building with Optional Center Girts Instructions Mueller Backyard Building Kits are not engineered structures and do not meet any specific building code criteria MUELLER
2 2 PARTS LIST Refer to the parts list on the itemized invoice delivered with your building. All parts are stenciled on the inside of the channel, purlin, girts and rafters. Example of this below:
3 3 SHEETING SCREW PLACEMENT WALL SHEETS 36" 10" 12" 12" Lap TEK Screw TEK Screw TEK Screw TEK Screw ROOF SHEETS 36" 10" 12" 12" Lap TEK Screw TEK Screw TEK Screw TEK Screw Place sealer tape between roof sheets only. NOTE: Make sure to use TEK screws to attach sheets to purlins, lap TEK screws to attach sheets to sheets.
4 4 BASE LAYOUT (SIDE CHANNEL AND BOT CHAN) NOTE: Leading and trailing edge of channels and columns are overbent for a tight fit. Spread apart as needed to nest the purlin into the channel. BC-1 BC-2 NOTE: Place only one bolt where shown to connect the MKB1 clip. The only vertical bolt to be installed at this time is the most inside one. The other bolt will be used when installing the corner column. BC-3 BC-1 BC-4 A level slab is critical for the base layout.
5 5 MAKE SURE THE ASSEMBLY IS SQUARE Make sure the assembly is square. Assembly is square when the corner to corner measurements are equal. Use temporary bracing to hold assembly square if required (temporary bracing is not included).
6 6 ANCHOR BOLT PLACEMENT NOTE: Make sure assembly is square. 10.5" Dia = 0.625" 24'-3" OUT-TO-OUT OF CONCRETE 1.5" 6'-5" 9'-0" 6'-5" 1'-2.5" 1'-2.5" 6'-9" 2" (To center not counting 1.5" sheeting ledge) 24'-3" OUT-TO-OUT OF CONCRETE 1'-5" 6'-2" 1'-5" 6'-9" 10.5" 2" (To center not counting 1.5" sheeting ledge) ANCHOR BOLT PLACEMENT Make sure the assembly is square. Assembly is square when the corner to corner measurements are equal. 2" (To center not counting 1.5" sheeting ledge) 2" (To center not counting 1.5" sheeting ledge) 1.5" 1.5" 1.5" 1'-2.5" 1'-2.5" 7'-5" 7'-0" 7'-5"
7 7 ANCHOR BOLT PLACEMENT DETAILS See Plan 4" 4" See Plan Jamb Depth 3" 3 1 /2" 1 1 /2" 4 1 /8" 1/4" Slope To Drain See Plan 5' 10" for NRD 7' 10" for WRD 1 1 /2" See Sheeting Recess TYP. SHEETING RECESS WITH BASE DRIP EDGE TRIM O.H. DOOR BOLT LAYOUT TYP. O.H. DOOR RECESS 1 1 /2" Dia = 5 /8" See Plan 1 1 /2" 2" (typ) Sheeting Ledge 2" 1 1 /2" Slope To Drain TYP. SHEETING RECESS WITHOUT BASE DRIP EDGE TRIM Sheeting Ledge 2" (typ) NOTE: One of the methods must be used. See erection details for additional information.
8 8 ERECTING COLUMNS (C-1) C-1 C-1 C-1 C-1 C-1 C-1 C-1 DJ-1 C-1 DJ-1 C-1 C-1
9 9 MKB1 CLIPS TO COLUMNS
10 10 MID-GIRTS (OPTIONAL MG-1, MG-2, MG-3 AND MG-4) DOOR HEADER (DH-1) MG-3 MG-2 MG-3 MG-4 MG-3 MG-2 MG-1 HEADER MG-3 MG-3 MG-1 MG-3
11 11 EAVE CHANNEL (EC-1) EC-1 EC-1
12 12 RAFTERS (R-1 AND R-2) R-1 R-2 R-2 R-1
13 13 ROOF PURLIN (RP-1, RP-2 AND RP-3) Open side of RP-1, RP-2 and RP-3 faces to center of building ROLL STOP CLIP (RS-1) RP-1 RP-2 RP-3 RP-2 RP-1 RS-1
14 14 WINDOW (OPTIONAL) Start sheet 1" past steel line. Sheet 1" above bottom of base channel Eave Trim Lap TEK Screw DripTrim Use inside/outside closures behind drip trim NOTE: Sheets below window will need to be field cut for window assembly. Insert window and flap flush to sheet. Add drip edge window trim when installing eave trim. See installation instructions included with the window packaging. 1" Endwall Sidewall 1" 1" past
15 15 SHEETING NOTE: Make sure the frame is plumb and level, and tighten all bolts prior to sheeting. Repeat for each wall. TOP VIEW Door Jamb Door Panel NOTE: For side with door, start sheets flush with J-trim on both sides of the door. J-Trim TEK Screw 1" 1"
16 16 SHEETING (NOTE SOME SHEETS ARE LONGER) NOTE: Sheets are stepped. Longer sheets are in the middle of the D.I.Y.
17 17 SHEETING ENDWALL WITH RUD DOOR To install the RUD, see the RUD video and instructions. Outside closures NOTE: If using optional walk door, set jamb trim inside measurement at 5'10⅛". 1" Inside closures IMPORTANT: 1" above the bottom of the base channel Sidewall TOP VIEW Endwall Inside closure goes on the bottom and outside closure goes on top. J-Trim NOTE: Start sheets inside of J-Trim 1" above the bottom of the base purlin
18 18 SHEETING SIDEWALL Endwall TOP VIEW Sidewall 1" Inside closure goes on the bottom and outside closure goes on top. NOTE: Start sheets 1" above the bottom of the base channel and 1" out from endwall
19 19 SHEETING ENDWALL WITHOUT DOOR TOP VIEW Sidewall Endwall Inside closure goes on the bottom and outside closure goes on top. 1" NOTE: Start sheets 1" above the bottom of the base purlin and 1" out from the sidewall
20 20 CORNER TRIM
21 21 BACK SIDE WALL Roof to wall sheet alignment Align major ribs from wall to major rib on roof NOTE: Make sure panels remain square during installation. 36" 10" 12" 12" Lap TEK Screw TEK Screw TEK Screw TEK Screw
22 22 36" 10" 12" 12" SHEETING THE ROOF Align roof sheets with wall sheets Place sealer tape between roof sheets to avoid leaks Lap TEK Screw TEK Screw TEK Screw TEK Screw Inside Closure Eave Trim SIDE VIEW 2.5" CAUTION: Use scaffold boards (not included) when installing roof panel sheets/trim NOTE: Use TEK screws at the purlins Use Lap TEK screws every 20" vertically
23 23 ROOFING TRIM DETAILS CAUTION: Use scaffold boards (not included) for support while installing roof sheets and trim. NOTE: A chalk line will assist in closure and ridge roll placement Outside Rake Lap TEK Screw Outside Rake Trim CUT AND FOLD AT CENTER
24 24 SKYLIGHT RIDGE ROLL INSTALLATION CAUTION: Use scaffold boards (not included) for support while installing roof sheets and trim HINT: Screw corner of ridge roll and middle first to maintain pitch. Install remainder of screws. Outside Closure Foam Block (under Ridge Roll) Ridge Roll Lap TEK Screw Roof Panel Install lap screws on ridge roll every 12 inches Foam Block closes the gap in between the closures.
25 25 TOTAL BUILDING MEASUREMENTS 8'2" 9'6" 24'3" 24'3"
Appendix A Door and Window Framing Last updated 5/21/2013
Appendix A Door and Window Framing Last updated 5/21/2013 1. First complete all previous framing for bay. Appendix A 1 Install all applicable columns, rafters, and/or eave purlins for the bay in which
More informationVENTED GABLE DETAIL ROOF PANEL GABLE FLASHING 24" C/C MAX. BUTYL SEALANT TAPE ROOF PURLIN FLASH AB-1, AB-2, AB-3, OR AB-4
ROOF PANEL GABLE FLASHING FASTENER @ 24" C/C MAX. ROOF PURLIN BUTYL SEALANT TAPE FLASH AB-1, AB-2, AB-3, OR AB-4 FASTENER @ EVERY MAJOR RIB OR 12" C/C MAX. F-J TRIM FABRAL ALUMINUM SOFFIT FASTENER 24"
More informationGIRTS ON BACK OF BUILDING
GIRTS ON BACK OF BUILDING ALL GIRTS ARE 1 1/2 SQUARE TUBE. GIRT LENGTHS FOR 12, 20, 24, AND 30 WIDE BUILDINGS: ON 12 WIDE BUILDINGS GIRTS ARE 67 3/4 LONG ON 20 WIDE BUILDINGS GIRTS ARE 56 3/4 LONG ON 24
More informationGLOSSARY OF TERMS SECTION 8
GLOSSARY OF TERMS SECTION 8 Anchor Bolt Angle Base Plate Bay Blocking CCB Centerline Chord Cladding Clip Closure Strip An A-307 steel bolt embedded in the concrete footing to anchor the base plate of the
More informationAppendix B Framing Component Installation Last updated 5/27/2013
Appendix B Framing Component Installation Last updated 5/27/2013 Apex Brace Installation Appendix B 1 Refer to apex connection detail on the engineering plans for the location of the apex brace. Refer
More informationGABLE ROOF CARPORT RECOMMENDED INSTRUCTION MANUAL
GABLE ROOF CARPORT RECOMMENDED INSTRUCTION MANUAL Table of Contents Introduction 2 Components 3 Step 1a Marking out the Perimeter of the Carport with Footing only 3 Step 2a Footing Set-Out for Concrete
More informationDUTCH GABLE CARPORT RECOMMENDED INSTRUCTION MANUAL
DUTCH GABLE CARPORT RECOMMENDED INSTRUCTION MANUAL Table of Contents Introduction 2 Components 3 Step 1a Marking out the Perimeter of the Carport with Footing only 4 Step 2a Footing Set-Out for Concrete
More informationVENTED GABLE DETAIL ROOF PANEL GABLE FLASHING 24" C/C MAX. BUTYL SEALANT TAPE ROOF PURLIN FLASH AB-1, AB-2, AB-3, OR AB-4
GABLE FLASHING FASTENER @ 24" C/C MAX. ROOF PURLIN BUTYL SEALANT TAPE FLASH AB-1, AB-2, AB-3, OR AB-4 FASTENER @ EVERY MAJOR RIB OR 12" C/C MAX. F-J TRIM FABRAL ALUMINUM SOFFIT FASTENER 24" C/C MAX. BUTYL
More informationWEB TRUSS ASSEMBLY MANUAL
protect what matters WEB TRUSS ASSEMBLY MANUAL Copyright Fall River Holdings, LLC. Phone #1-800-825-0316 http://www.worldwidesteelbuildings.com/ Building Erection Manual (Rev-4) 1.21.15 1 Table of Contents
More information9 x 12 BackYard Building. Installation Information
9 x 12 BackYard Building Installation Information Product Information Building Code Disclaimer Safety First! Back Yard Building METAL DEPOTS DOES NOT WARRANT OR REPRESENT ITS BACKYARD SERIES BUILDINGS
More informationTYPICAL FRAMING AND STITCH FASTENER PATTERNS FOR MAX-RIB PANELS
TYPICAL AND PATTERNS FOR MAX-RIB S MAX-RIB (PATTERN #1) @ 1'-8" O.C. (MAX.) ROLL TAPE SEALANT @ SEAMS MAX-RIB @ 1'-8" O.C. (MAX.) ROLL TAPE SEALANT @ SEAMS MAX-RIB TRIM (PATTERN #3) NOTE: TAPE SEALANT
More information900 SERIES WALL PANELS
CI-DS-01-900 CI-PP-01-900 CI-PJ-01-900 CI-PJ-02-900 CI-PJ-03-900 CI-BS-01-900 CI-BS-02-900 CI-BS-03-900 CI-BS-04-900 CI-BS-05-900 CI-OC-01-900 CI-OC-02-900 CI-IC-01-900 CI-FO-01-900 CI-FO-02-900 CI-FO-03-900
More informationClopay Models 835/837 Sliding Door System Installation Guide
Clopay Models 835/837 Sliding Door System Installation Guide The aim of this instruction is to guide you through the process of construction and fitting of Sliding Doors. Due to the number of sizes available
More informationE-Z BUILD STEEL BARN 12' 12' 12' 16' 12' 20'
E-Z BUILD STEEL BARN 12' 12' 12' 16' 12' 20' BUILD You can construct your own E-Z frame barn with the help of this step by step guide. North American softwood dimensional lumber sizes: Nominal Actual in
More informationChapter 51: Sidewall Overhang(s) Only - Enclosed
Chapter 51: Sidewall Overhang(s) Only - Enclosed Most Common Mistakes: 1. Incorrect eave height. 2. Placing eave girt below truss tails. 3. Fascia board top edges not bevel cut to match roof slope. 4.
More informationINSTALLATION INSTRUCTIONS LS X 12-2 X 7 1/2 FRAME LOAFING SHED
INSTALLATION INSTRUCTIONS LS-30 30 X 12-2 X 7 1/2 FRAME ACTUAL FRAME BASE SIZE: 30 X 12-2 LOAFING SHED Our unique assembly process quickly transforms the individual pieces into a finished structure that
More informationStoring, Handling, and Cutting Steel Panels
Storing, Handling, and Cutting Steel s Storing Specifically check your quantities, colors, and lengths All materials should be used as soon as possible Steel bundles should be stored indoors with enough
More informationINSTALLATION INSTRUCTIONS LS X 12-2 X 7 1/2 FRAME LOAFING SHED
INSTALLATION INSTRUCTIONS LS-12 12 X 12-2 X 7 1/2 FRAME ACTUAL FRAME BASE SIZE: 12 X 12-2 LOAFING SHED Our unique assembly process quickly transforms the individual pieces into a finished structure that
More information4-SIDED NAVAJO SHELTER ARIZONA MODEL INSTALLATION INSTRUCTIONS
4-SIDED NAVAJO SHELTER ARIZONA MODEL INSTALLATION INSTRUCTIONS Recommended Tools: Before You Begin: Saftey Glasses, Tape Measure, Carpenters Level, Framing Square, Hex Head Nut Drivers, Chalk Line, Elec.
More informationPOST FRAME CONSTRUCTION MANUAL
POST FRAME CONSTRUCTION MANUAL www.pole-barn.info www.apbbuildings.com TABLE OF CONTENTS 3. Jobsite Preparation 4. Setting Foundation Posts 5. Setting Corner Posts 6. Sidewall & Endwall Posts 7. Grade
More informationASSEMBLY INSTRUCTIONS FOR VERSATUBE VERTICALLY SHEETED 2 x3 SINGLE SLOPE LOAFING SHED 12 W X 18 2 / 30 2 / 42 2 L X 8 / 10 6 ON CENTER FRAMES
ASSEMBLY INSTRUCTIONS FOR VERSATUBE VERTICALLY SHEETED x3 SINGLE SLOPE LOAFING SHED W X 8 / 30 / L X 8 / 0 ON CENTER FRAMES Our unique assembly process quickly transforms the individual pieces into a finished
More informationSTEEL BUILDINGS RECOMMENDED INSTALLATION GUIDE
STEEL BUILDINGS RECOMMENDED INSTALLATION GUIDE 3 TO 30 METRE SPAN FRAME FIRST METHOD SUPPLIED BY: Last update 2 May 2008 2008 FBHS (Aust) Pty Limited FBHS (Aust) Pty Limited ABN 83 126 232 504 trading
More informationBest Barns USA. the Brookhaven 10' x 16' Assembly Book. revised March 23, 2016
Best Barns USA Assembly Book revised March 23, 2016 the Brookhaven 10' x 16' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is copyrighted.
More informationUNIVERSAL ASSEMBLY INSTRUCTIONS FOR VERSATUBE FRONTIER GARAGE BUILDINGS
UNIVERSAL ASSEMBLY INSTRUCTIONS FOR VERSATUBE FRONTIER GARAGE BUILDINGS Our unique assembly process quickly transforms the individual pieces into a finished structure that will give you years of service.
More informationINSTRUCTION MANUAL FOR MULTIBUILD AMERICAN BARN
INSTRUCTION MANUAL FOR MULTIBUILD AMERICAN BARN SUPPLIED BY: LAST UPDATED April 26, 2006 2001 AS&G Building Systems AMERICAN BARN The American Barn uses similar components to other steel frame buildings.
More informationVariety of material thicknesses
Secondary Framing 1 Secondary Framing Materials 2 Secondary Framing Variety of material thicknesses Thickness range from 17 gage to 11 gage Acrylic-coated coated galvanized secondary ( VP Tech Perspective#38)
More informationINSTRUCTION MANUAL FOR MULTIBUILD VERTICAL CLAD QUAKER BARN WITH OR WITHOUT OUT MEZZANINE FLOOR UP TO 12 METRE SPAN
INSTRUCTION MANUAL FOR MULTIBUILD VERTICAL CLAD QUAKER BARN WITH OR WITHOUT OUT MEZZANINE FLOOR UP TO 12 METRE SPAN SUPPLIED BY: LAST UPDATED March 11, 2003 2001 AG&S Building Systems, Sydney Australia
More informationUNIVERSAL ASSEMBLY INSTRUCTIONS FOR VERTICALLY SHEETED GARAGE BUILDINGS BUILDING WIDTHS: 12, 20, 24, AND 30
UNIVERSAL ASSEMBLY INSTRUCTIONS FOR VERTICALLY SHEETED GARAGE BUILDINGS BUILDING WIDTHS: 12, 20, 24, AND 30 SINGLE DOOR GARAGE AVAILABLE IN 12, 20, 24 AND 30 WIDTHS DOUBLE DOOR GARAGE AVAILABLE IN 24 AND
More informationSAMPLE INSTRUCTIONS. Best Barns USA Assembly Book. the Belmont with pocket doors. Building Size 12'x16' or 12'x20' Revised January 10, 2012
Best Barns USA Assembly Book Revised January 10, 2012 SAMPLE INSTRUCTIONS the Belmont with pocket doors Building Size 12'x16' or 12'x20' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive
More informationINSTALLATION INSTRUCTIONS LS X 12-2 X 7 1/2 FRAME LOAFING SHED
INSTALLATION INSTRUCTIONS LS-12 12 X 12-2 X 7 1/2 FRAME ACTUAL FRAME BASE SIZE: 12 X 12-2 LOAFING SHED Our unique assembly process quickly transforms the individual pieces into a finished structure that
More informationINSTALLATION INSTRUCTIONS LS X 12-2 X 7 1/2 FRAME LOAFING SHED
INSTALLATION INSTRUCTIONS LS-24 24 X 12-2 X 7 1/2 FRAME ACTUAL FRAME BASE SIZE: 24 X 12-2 LOAFING SHED Our unique assembly process quickly transforms the individual pieces into a finished structure that
More informationDoor Canopy. PDL Building Products Industrial Parkway, N. Olmsted, OH Phone:
Door Canopy Door Canopies are attractive and efficient while eliminating the need and expense of drafting and manufacturing canopies as part of the building package. Construction: 26 gauge material around
More informationRoof Only Lean-to Instruction Manual
Roof Only Lean-to Instruction Manual for 10 x 20 2 x 8 /10 6 covers Our unique assembly process quickly transforms the individual pieces into a finished structure that will give you a lifetime of service.
More informationGambrel Barn Construction Manual 8x8 through 16x24 Units
Gambrel Barn Construction Manual 8x8 through 16x24 Units Tools Needed: Cordless drill (12V or higher) #2 square drive bit Hammer 6 step ladder Tape measure Square utility knife w/ blade & hook blade Little
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised June 14, 2017 the Glenwood Building Size 12' x 16' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive - Greenville, PA 16125 This manual is copyrighted.
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised November 19, 2015 the Glenwood Building Size 12' x 20' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised June 14, 2017 the Belmont-R Building Size 12' x 24' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive - Greenville, PA 16125 This manual is copyrighted.
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised June 14, 2017 the Glenwood Building Size 12' x 24' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive - Greenville, PA 16125 This manual is copyrighted.
More informationFLAT ROOF CARPORT RECOMMENDED INSTRUCTION MANUAL
FLAT ROOF CARPORT RECOMMENDED INSTRUCTION MANUAL Table of Contents Introduction... 2 Components... 3 Step 1 Marking out the Perimeter of the Carport... 3 Step 2a Footing Set-Out for Concrete Block Pad
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised September 13, 2017 the Belmont Building Size 12' x 16' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 This manual is copyrighted.
More informationPrecut Value Shed Manual Gambrel Barn
Tools Needed: -Cordless Drill (12V or higher) -#2 Square Drive Bit -Hammer -6 Step Ladder -Tape Measure -Square utility knife w/ blade & hook blade -Speed Square Little Cottage Co. PO Box 455 Berlin, OH
More informationSafety Glasses Safety Gloves Ladders Measuring Tape Spirit Level String Line. Tin-Snips Rivet Gun Caulking Gun Silicone Socket Set
BEFORE YOU START Carefully read these instructions and refer to them constantly during each stage of construction. If you do not have all the necessary tools or information, contact Stratco for advice.
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised July 27, 2012 the North Dakota with pocket doors 12' x 20' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This
More informationSAMPLE INSTRUCTIONS. Best Barns USA Assembly Book. the North Dakota with pocket doors. Building Size 12'x12' or 12'x16' Revised August 30, 2011
Best Barns USA Assembly Book Revised August 30, 2011 SAMPLE INSTRUCTIONS the North Dakota with pocket doors Building Size 12'x12' or 12'x16' Manufactured by Reynolds Building Systems, Inc. 205 Arlington
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised September 12, 2017 the Arlington Building Size 12' x 16' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 This manual is copyrighted.
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised September 13, 2017 the North Dakota with pocket doors 12' x 20' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 This manual
More informationDura-Lock Roof System
DLR-14 Dura-Lock Roof System Assembly and Installation Instructions Read the instructions before starting the job. They explain the steps required to produce a finished product that will meet factory specifications.
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised March 6, 2017 the Arlington Building Size 12' x 24' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive - Greenville, PA 16125 This manual is copyrighted.
More informationLedger Board Lean-to Instruction Manual
Ledger Board Lean-to Instruction Manual for 18 x 24 2 x 8 /12 6 covers ROOF ONLY ROOF WITH GABLES 2-SIDED FRAME ONLY 2-SIDED WITH GABLES Our unique assembly process quickly transforms the individual pieces
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised November 19, 2015 the Arlington-R Building Size 12' x 20' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This
More informationUNIVERSAL ASSEMBLY INSTRUCTIONS FOR VERSATUBE GARAGE BUILDINGS
UNIVERSAL ASSEMBLY INSTRUCTIONS FOR VERSATUBE GARAGE BUILDINGS SINGLE DOOR GARAGE AVAILABLE IN 12, 20, 24 AND 30 WIDTHS DOUBLE DOOR GARAGE AVAILABLE IN 24 AND 30 WIDTHS Our unique assembly process quickly
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised November 19, 2015 the Arlington-R Building Size 12' x 24' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This
More informationBest Buy Metals Toll Free / Phone / Fax
DETAIL MANUAL for Vertical Seam Best Buy Metals Toll Free 1-800-728-4010 / Phone 423-479-6382 / Fax 423-728-3066 www.bestbuymetals.com Vertical Seam Roofing Panels Fig. 2 Vertical Seam Has 1-3/4" high
More informationLedgewood Farm greenhouse. construction
Ledgewood Farm greenhouse How do I Start? construction to I m Finished! Post layout The string will be 7 above the ground and the posts will be driven until the proper drill hole is at the string. Spacing
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised September 12, 2017 the Arlington Building Size 12' x 20' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 This manual is copyrighted.
More informationSLATE & SHINGLE INSTALLATION
EAVE EDGE Apply a small strip of roofing paper to the bottom of eave. Eave flashing is attached to substrate with roofing nails every 9". Install underlayment over entire roof. (See Fig. 1) PAGE 1 Bend
More informationBest Barns. 10' x 16' the Elm R. Assembly Book. revised September 29, 2016
Best Barns Assembly Book revised September 29, 2016 the Elm R 10' x 16' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive - Greenville, PA 16125 This manual is copyrighted. Under the
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised September 13, 2017 the North Dakota with pocket doors Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 Building Size 12'x12'
More informationTABLE OF CONTENTS A. PBR
TABLE OF CONTENTS A. PBR Panel 1. PBR Panel Architect/Engineer Information....................................... 2 2. PBR Panel UL 90 Requirements............................................... 3 3. PBR
More informationSTEEL BUILDINGS RECOMMENDED INSTALLATION GUIDE
STEEL BUILDINGS RECOMMENDED INSTALLATION GUIDE 3 TO 30 METRE SPAN FRAME FIRST METHOD SUPPLIED BY: Last update 19 September 2011 2011 FBHS (Aust) Pty Limited FBHS (Aust) Pty Limited ABN 83 126 232 504 trading
More informationChapter 16: Roof Steel
Chapter 16: Roof Steel Most Common Mistakes: 1. Roof purlins not checked for alignment. 2. Failure to properly square roof. 3. Reversing steel laps. 4. Using not enough or too many screws. 5. Over or under
More informationUNIVERSAL ASSEMBLY INSTRUCTIONS FOR VERSATUBE 2 x 3 DESIGN-YOUR-OWN FRONTIER GARAGE BUILDINGS
UNIVERSAL ASSEMBLY INSTRUCTIONS FOR VERSATUBE 2 x 3 DESIGN-YOUR-OWN FRONTIER GARAGE BUILDINGS PLEASE VISIT - https://youtu.be/fzhwt-tmt_q FOR VIDEO TUTORIAL OF A FRONTIER BUILDING ASSEMBLY Our unique assembly
More informationAssembly Book. 10' x 12' the Cambridge II. revised June 13, 2014
Assembly Book revised June 13, 2014 the Cambridge II 10' x 12' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is copyrighted. Under the
More informationGrowSpan Series 500 Door Kits
GrowSpan Series 500 Door Kits Double Swinging Door Finished Grade Finished Grade Diagram shows a double-swinging door centered and installed in an end wall frame. The door kit includes materials for the
More informationSTEEL BUILDINGS RECOMMENDED INSTALLATION GUIDE
STEEL BUILDINGS RECOMMENDED INSTALLATION GUIDE 3 TO 30 METRE SPAN TILT UP METHOD SUPPLIED BY: Last update 19 September 2011 2011 FBHS (Aust) Pty Limited FBHS (Aust) Pty Limited ABN 83 126 232 504 trading
More information16 & 20 FT. WIDE GROUND TO GROUND
CF SERIES 1000 16 & 20 FT. WIDE GROUND TO GROUND conleys.com CF Series 1000 Ground to Ground outstanding features Two-piece arch that laps and bolts together Simple to install Arches nest together for
More information900 SERIES PANEL SHEET INDEX STAGGERED ENDLAP STAGGERED MALE LEG AT ENDLAP CONTINUOUS FEMALE ENDLAP INSTALLATION SEQUENCE CI-WR
900 SERIES PANEL CI-DS-01-900 CI-PJ-01-900 CI-PJ-02-900 CI-EL-01-900 CI-EL-02-900 CI-EL-03-900 CI-EL-04-900 CI-EL-05-900 CI-EL-06-900 CI-EL-07-900 CI-EL-08-900 CI-RD-01-900 CI-RD-02-900 CI-RD-03-900 CI-EV-01-900
More informationDOCK WEDGE - STANDARD
DOCK WEDGE - STANDARD INSTALLATION INSTRUCTIONS WOOD HEADER READ ALL INSTRUCTIONS BEFORE INSTALLING SEAL. SUPER SEAL MFG. LTD. WILL NOT BE HELD RESPONSIBLE FOR IMPROPER INSTALLATION OF ANCHORING DEVICES,
More informationFive Star Panel Installation Instructions
Five Star Panel Installation Instructions How to Store Five Star Panels You will need to store FIVE STAR PANELS in dry place to prevent staining, deterioration and possibly void all warranties. Stand the
More informationASSEMBLY INSTRUCTIONS FOR VERTICALLY SHEETED CARPORTS
ASSEMBLY INSTRUCTIONS FOR VERTICALLY SHEETED CARPORTS WIDTHS: 12, 20 & 24 5 ON CENTER FRAMES Our unique assembly process quickly transforms the individual pieces into a finished structure that will give
More informationInstallation Instructions for Solar Snow Pad (SSP-T-3)
Installation Instructions for Solar Snow Pad (SSP-T-3) Warning- Do not use this product on solar arrays where the calculated array snow loads exceed 50 pounds per square foot (psf). Most solar panels are
More informationthe Greenbriar 12' x 20' Best Barns USA Assembly Book Revised April
Best Barns USA Assembly Book Revised April 28 2015 the Greenbriar 12' x 20' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is copyrighted.
More informationRetrofit OptiLiner Banded Liner System
General Introduction The Owens Corning OptiLiner Banded Liner System is designed to provide maximum thermal performance in pre engineered metal buildings using Owens Corning metal building insulation.
More informationGambrel Barn with Overhang Manual
Tools Needed: -Cordless Drill (12V or higher) -#2 Square Drive Bit -Hammer -6 Step Ladder -Tape Measure -Square utility knife w/ blade & hook blade -Speed Square Little Cottage Co. PO Box 455 Berlin, OH
More informationE-Z GROW HOBBY GREENHOUSE. I n s t r u c t i o n M a n u a l & D i s c l a i m e r s
E-Z GROW HOBBY GREENHOUSE I n s t r u c t i o n M a n u a l & D i s c l a i m e r s Contractors/Installers Note: This manual is the property of the customer. Please leave it in the possession of the customer.
More informationUNIVERSAL ASSEMBLY INSTRUCTIONS FOR VERSATUBE GARAGE BUILDINGS
UNIVERSAL ASSEMBLY INSTRUCTIONS FOR VERSATUBE GARAGE BUILDINGS SINGLE DOOR GARAGE AVAILABLE IN 12, 20, 24 AND 30 WIDTHS DOUBLE DOOR GARAGE AVAILABLE IN 24 AND 30 WIDTHS Our unique assembly process quickly
More informationTwin-Wall Double Swinging Door Kit
115021 Twin-Wall Double Swinging Kit READ THIS DOCUMENT BEFORE YOU BEGIN Thank you for purchasing this GrowSpan door kit. When properly assembled and maintained, this product will provide years of reliable
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised September 12, 2017 the Easton 12'x 16' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive - Greenville, PA 16125 This manual is copyrighted. Under
More informationLedger Board Lean-to Instruction Manual
Ledger Board Lean-to Instruction Manual for 18 x 24 2 x 8 covers Our unique assembly process quickly transforms the individual pieces into a finished structure that will give you a lifetime of service.
More informationBest Barns. 10' x 12' the Elm R. Assembly Book. revised September 29, 2016
Best Barns Assembly Book revised September 29, 2016 the Elm R 10' x 12' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive - Greenville, PA 16125 This manual is copyrighted. Under the
More informationIMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS
IMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS ** READ ALL INSTALLATION INSTRUCTIONS BEFORE STARTING!** If at any point, you have questions, call 1-800-851-0865...(The manufacturer will not be responsible
More informationOptiLiner Banded Liner System Bi-Directional Banding
TOP LAYER UNFACED INSULATION ROOF SHEET LINER BOTTOM LAYER UNFACED INSULATION General Introduction The OptiLiner Banded Liner System is designed to provide maximum thermal performance in preengineered
More informationAWNING / PATIO COVER INSTALLATION INSTRUCTIONS
AWNING / PATIO COVER INSTALLATION INSTRUCTIONS Before You Begin Read the installation instructions thoroughly before beginning the installation procedure. Perspective In the Awning Instructions, Back means
More informationASSEMBLY INSTRUCTIONS FOR VERSATUBE VERTICALLY SHEETED 2 x3 & 2 x4 CARPORTS WIDTHS: 12, 16, 20, 24, 30, 36 & 40 4 & 5 ON CENTER FRAMES
ASSEMBLY INSTRUCTIONS FOR VERSATUBE VERTICALLY SHEETED 2 x3 & 2 x4 CARPORTS WIDTHS: 12, 16, 20, 24, 30, 36 & 40 4 & 5 ON CENTER FRAMES Our unique assembly process quickly transforms the individual pieces
More informationKS SERIES - VERTICAL INSTALLATION
CS-DS-01-KSV CS DISCLAIMER CS-PJ-01-KSV KS42SL EXPANDED PANEL JOINT CS-PJ-02-KSV KS42SL ENGAGED PANEL JOINT CS-PJ-03-KSV KS45SL EXPANDED PANEL JOINT CS-PJ-04-KSV KS45 FLAT ENGAGED PANEL JOINT CS-PJ-05-KSV
More informationBUILDING GUIDE FOR MULTIBUILD ALL STEEL BUILDINGS 3 TO 30 METRE SPAN
BUILDING GUIDE FOR MULTIBUILD ALL STEEL BUILDINGS 3 TO 30 METRE SPAN SUPPLIED BY: 26 Dobney Ave, Wagga Wagga. NSW. 2650 PH: 02 6925 5719, Fax 02 6925 2895 Email: sales@havashed.com.au, Web Address: www.havashed.com.au
More informationSliding Door Kit
YOU MUST READ THIS DOCUMENT BEFORE YOU BEGIN TO ASSEMBLE THE DOOR KIT. Thank you for purchasing this GrowSpan door kit. When properly assembled and maintained, this product will provide years of reliable
More informationQwik-Fence Installation Instructions
Qwik-Fence Installation Instructions 1 Tools Required The following installation instructions should be used as a guide for installing Folding Guard Qwik-Fence Partitions. Good common sense and appropriate
More informationChapter 9: Truss Preparation
Chapter 9: Truss Preparation Most Common Mistakes: 1. Placing purlins at a spacing other than what is shown on building plans. 2. Not following a continuous layout (keep spacing the same, unless noted
More informationInstallation Guide. Please read before installing SIPs Kit. 1 Method Statement for the erection of a SIPS Industries Kit Materials...
30a Renewable Chase Bibra Lake WA 6163 Tel: (08) 9494 2211 Fax: (08) 9494 2202 Email: info@sipsindustries.com.au Web: www.sipsindustries.com.au Installation Guide Please read before installing SIPs Kit.
More informationTuff Rib Panel Installation Specifications
Tuff Rib Panel Installation Specifications ROOF APPLICATION: Roof slope must be a minimum of a 2/12 pitch to use this product. For slopes lower than a 3/12 pitch, lap sealant is suggested on the side laps
More informationIMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS FOR AZTEC SHELTER
IMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS FOR AZTEC SHELTER ** READ ALL INSTALLATION INSTRUCTIONS BEFORE STARTING!** If at any point, you have questions, call 1-800-851-0865...(The manufacturer will
More informationBest Barns. the Cypress R 10' x 16' Assembly Book. revised February 19, 2016
Best Barns Assembly Book revised February 19, 2016 the Cypress R 10' x 16' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is copyrighted.
More informationAssembly Book. the Fairview. Building Size 12'x12' Revised July 25, 2012
Assembly Book Revised July 25, 2012 the Fairview Building Size 12'x12' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is copyrighted.
More informationProSnap 100 STANDARD DETAILS
ProSnap 100 OVER WOOD DECK STANDARD DETAILS Austin - Headquarters/Sales Office 830 Sagebrush Drive Austin, TX 78758 (512) 452-1515 (800) 428-7412 Fax (512) 833-7499 www.ctmrs.com email: info@ctmrs.com
More informationOptiLiner Banded Liner System Bi-Directional Banding
TOP LAYER UNFACED INSULATION ROOF SHEET ING LINER BOTTOM LAYER UNFACED INSULATION General Introduction The is designed to provide maximum thermal performance in preengineered metal buildings using Owens
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised October 11, 2018 the Woodville 10' x 16' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 This manual is copyrighted. Under
More informationSkypod. Pitched PVC-U skylights. Installation guide PITCHED PVC-U SKYLIGHTS ISSUE 1
Skypod Pitched PVC-U skylights PITCHED PVC-U SKYLIGHTS Installation guide ISSUE 1 Skypod pitched PVC-U skylights Installation guide Contents 1. Surveying 3 2. Installation 4 3. Additional information 10
More informationGrowSpan Estate Pro I Greenhouse
GrowSpan Estate Pro I Greenhouse Photo may show a different but similar model. 2016 Growers Supply All Rights Reserved. Reproduction is prohibited without permission. STK# DIMENSIONS 104564 11'-8" W x
More informationBest Barns USA Assembly Book
Best Barns USA Assembly Book Revised September 19, 2016 the Meadowbrook-R 16' x 10' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is
More information