OWNER S MANUAL. Clayton Hex Gazebo with Netting. Product code: D71 M80928 UPC code: Vendor Item: SS-I-138-2NGZ. Date of purchase: / /

Transcription

1 OWNER S MNUL layton Hex azebo with Netting Product code: D71 M80928 UP code: Vendor Item: SS-I-138-2NZ Date of purchase: / / 1

2 Special Warning ssemble your gazebo on a soft, non-abrasive surface to avoid damage. The gazebo is heavy. Use care when handing. ssembly by four adults is recommended. The gazebo is not intended to be a permanent structure. Take it down during high winds or it may be damaged. KEEP LL FLME ND HET SOURES WY FROM NOPY FBRI The canopy is made with flame-resistant fabric which meets PI-84 specifications. It is not fireproof. The canopy fabric will burn if left in continuous contact with flame source. The application of any foreign substance to the canopy fabric may render the flame-resistant properties ineffective. aution: This gazebo is made for explicit purpose of providing limited outdoor sun shade and is not to be used as a toy, shelter or tent. This gazebo is not intended for inclement weather in any form including, but not limited to: rain, hail, sleet, snow and/or wind. Do not locate structure near any open flame. Do not use structure as a support. Do not shake, lean or climb on structure. hildren under age of 10, near the structure, should be supervised by a competent adult at all times. PRTS Read through all the instructions before beginning assembly. Unpack and identify all the parts. Place them on a flat, non-abrasive surface. ssembly by six people is recommended. (6) Leg Post B (6) Top rossbar (4) Decorative Panel D (2) Tabletop rossbar E (1) F (6) anopy Frame anopy Frame Short Bar (4) Tabletop Surpport Long Bar H (2) Tabletop Surpport Short Bar I (1) J (1) Tabletop Tabletop (with I label) (with J label) K (1) Tabletop (with K label) L (1) Tabletop (with L label) 2

3 M (1) anopy Fabric N (6) Net ESSORIES ( spare) M6 x 15L Bolt Ob ( spares) M6 x 20L Bolt Oh (12) Lawn Stake Oi (1) Hook Oc (6 + 1 spare) M6 x 25L Bolt Oj (2) Open Hex Wrench Od ( spare) M6 x 30L Bolt Ok (2) llen Wrench ( spares) Metal Washer ( spare) Nut Og (6) Bracket Ol (1) Touch-up Paint Om (1) ssembly Instructions Sheet 3

4 SSEMBLY INSTRUTIONS 1 ttach a decorative panel () to two leg posts (). Insert two hooks of decorative panel () into two holes of two leg posts (). See Fig. 1. Then insert the pins through the decorative panel () and into the leg post () for each hole. See Fig. 2. Repeat procedure for the remaining decorative pannels () and leg posts (). Fig. 1 Fig. 2 Og Fig. 3 Ob 2 ttach a top crossbar (B) to the assembled frame (&). Line up all holes and for each hole insert an M6 x 20L bolt (Ob) through a metal washer (), top crossbar (B) and secure into leg posts (). Don t tighten completely. Repeat procedure for the other side and the remaining top crossbars (B). ttach a bracket (Og) to a leg post (). Line up all holes and for each hole insert an M6 x 20L bolt (Ob) through a metal washer () and secure into the post (). Don t tighten completely. Repeat procedure for the remaining leg posts (). See Fig. 3. Tighten all bolts. B Ob B 4

5 3 ttach a tabletop crossbar (D) to the assembled frame (&) Line up all holes, for each hole insert an M6 x 15L bolt () through the bracket of tabletop crossbar (D) and secure into the leg post () or the decorative pannel (). Don t tighten completely. Repeat procedure for the remaining tabletop crossbars (D). See Fig. 4. and Fig. 5. Tighten all bolts. NOTE: The holes of tabletop crossbars (D) facing inside (For attaching to tabletops). Fig. 4 D D D D Fig. 5 4 ttach the canopy short bars (F) to the canopy frame (E). For each hole, insert an M6 x 30L bolt (Od) through a metal washer (), canopy frame (E), short bar (F), another metal washer () and secure with a nut (). Tighten all bolts and nuts. Repeat procedure for the remaining five short bars (F). See Fig. 6. F E Od E E F Fig. 6 F 5 Place the canopy fabric (M) to the assembled canopy frame (E&F). Insert each top short bars of canopy frame (E) into each top pockets of the canopy fabric (M). Pull down the canopy fabric and spread to the location. See Fig. 7. Fig. 7 M 5

6 6 Place the completed canopy onto the top of assembled leg posts. Line up the holes, for each hole insert an M6 x 30L bolt (Od) through a metal washer (), a short bar (F), a bracket (Og), another metal washer () and secure with a nut (). Don t tighten completely. Repeat procedure for the remaining five short bars (F). Tighten all bolts and nuts. See Fig. 8. Pull down the edges of the canopy fabric and insert each tip of the canopy short bar (F) into the pocket of the canopy fabric. Od Og F Fig. 8 7 : ttach the tabletop (I) to the tabletop crossbar (D). Line up the hole, insert an M6 x 20L bolt (Ob) through a metal washer (), the tabletop (I) and secure into the tabletop crossbar (D) for each hole. See Fig. 9. Don t tighten completely. ttach the support long bar () to the decorative panel (), insert an M6 x 15L bolt () through the support long bar () and secure into the decorative panel (). See Fig. 10. Don t tighten completely. ttach the support long bar () to the tabletop (I), insert an M6 x 25L bolt (Oc) through a metal washer (), the support long bar () and secure into the tabletop (I). See Fig. 11. Don t tighten completely. Fig. 11 Oc I Fig. 9 Ob I Fig. 12 Ob : ttach the tabletop (J) to the tabletop crossbar (D). See Fig. 12. ttach the tabletop (J) to the tabletop (I). Line up the hole, insert an M6 x 20L bolt (Ob) through a metal washer (), the tabletop (J), the tabletop (I), another metal washer () and secure with a nut (). ttach the support short bar (H) to the decorative panel (), insert an M6 x 15L bolt () through the support short bar (H) and secure into the decorative panel (). See Fig. 13. Don t tighten completely. ttach the support short bar (H) to the tabletop (J&I), insert an M6 x 25L bolt (Oc) through a metal washer (), the tabletop (J&I), the support short bar (H), another metal washer () and secure with a nut (). See Fig. 14. Don t tighten completely. Fig. 10 I J I H Fig. 13 K J Ob I H L Oc J Fig. 14 6

7 : Repeat step for remaining tabletop (K&L). Fig. 15 : ttach the tabletop (J&I) to the tabletop (K&L). Line up the hole, insert an M6 x 15L bolt () through the support long bar () and secure into the decorative panel () for total of 2 holes. See Fig. 15. Don t tighten completely. ttach the support long bar () to the tabletop (J&K), insert an M6 x 25L bolt (Oc) through a metal washer (), the support bar () and secure into the tabletop (J&K). Don t tighten completely. Then insert an M6 x 20L bolt (Ob) through a metal washer (), the tabletop (K&J), another a metal washer () and secure with a nut () for total of 2 holes. See Fig.16 and Fig. 17. Don t tighten completely. : Tighten all bolts and nuts. Oc J Fig. 16 I J Oc Ob K J K L K Ob Fig. 17 Fig. 19 Oi 8 Secure the gazebo to the ground by inserting the lawn stakes (Oh) through the holes at the bottom of the leg post into the ground. See Fig. 18. ttach the S shaped hook (Oi) to the ring of the canopy. The S shaped hook is used for hanging decoration items if necessary. See Fig. 19. Oh Fig. 18 7

8 9 Locate the nets (N) to the net bars of top crossbars (B) with Velcro tabs. See Fig. 20. Make sure the top crossbar is between two edges of the canopy fabric (M). ffix inner edges with Velcro tabs. See Fig. 21. F Fig. 20 B N Fig. 21 M Your gazebo is now ready for use. Enjoy! N RE INSTRUTIONS Wash with a mild solution of soap and water; rinse thoroughly. Dry completely. Do not use bleach or solvents. over furniture with outdoor furniture covers when not in use. Please refer to part numbers when reordering For questions or comments about product: all toll-free: Made in HIN Distributed by Sears, Roebuck and o., Hoffman Estates, IL See our extensive assortment of outdoor living products on-line at and 8