DASHLEY COLLECTION GAZEBO

Transcription

1 DASHLEY COLLECTION GAZEBO MODEL NO INSTRUCTIONS Toll-free: IMPORTANT: Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference.

2 MADE IN CHINA IMPORTED BY TRILEAF DISTRIBUTION TRIFEUIL TORONTO, CANADA M4S 2B8

3 3 Table of contents 3 Important safety instructions 3 Parts list 4 General requirements 7 Assembly 8 Cleaning and maintenance 28 Specifications 28 Warranty 29 TABLE OF CONTENTS Warning! To reduce the risk of serious injury, read the following safety instructions before assembling and using the gazebo. Caution! Always keep children under close supervision while they are playing around this product. Never leave children unattended. Keep pets away while setting up the gazebo. Caution! Check municipal by-laws prior to installing the gazebo. This product is intended for domestic outdoor use only. The product should be placed and assembled on flat, horizontal ground. Consult with your local governing authority/local municipal codes regarding installation of temporary structures before assembly. Ensure there is enough clearance around the product. Before assembling the gazebo, make sure to leave a distance of not less than 6 (1.8 m) from any structures or obstructions, such as fences, garages, houses, overhanging branches, laundry lines, or electrical wires. Anchor the gazebo to the ground with stakes for added safety. Stakes are provided to secure the gazebo to the ground. If you wish to secure the gazebo to a concrete or wood surface, use anchors suited for these surfaces (anchors not included). Do not assemble the gazebo on sandy, muddy or loose soil, as stakes do not have enough anchorage in these types of soil. If more than one gazebo is set up, keep a minimum distance of 10' (3 m) between the gazebos. Any assembly or maintenance of the product must be carried out by adults only. Make sure there is sufficient manpower when assembling or moving the product. Some parts may contain sharp edges. Wear protective gloves if necessary. Check all nuts and bolts periodically for tightness. When required, tighten them. Repairing and replacing parts should be done by a qualified technician. This gazebo is intended for decorative and sunshade purposes only. The gazebo is not designed to withstand harsh weather, including high winds, rain and snow. Always remove the gazebo in such heavy weather conditions, otherwise it might tip over and cause damage to the product or injuries to bystanders. During snow days, remove the snow at the top when the snow is thicker than 4" (10 cm). After a period of time, usually in 2 3 months, tighten all the bolts. After a period of use, rinse the ash on top of the gazebo using water. Avoid using acid or alkali wash lotion. Do not hang any weights on the roof frame. Do not climb onto the roof of the gazebo. Falling off the gazebo can result in serious injury. After a few years, if the paint peels off, use paint of similar colour. It is recommended to use outdoor paint. Retain the original packaging to store the gazebo. If the product will not be used for a long period of time (e.g. winter time), it should be disassembled and stored in a clean, dry environment. IMPORTANT SAFETY INSTRUCTIONS IMPORTANT: Retain for future reference, and read carefully.

4 4 PRODUCT NO A Post - 4 J1 Frame for long side under big roof - 2 PARTS LIST B Base - 4 C Base cover - 4 D1 Beam for long side - 2 J2 Frame for short side under big roof - 2 K1 Small roof top beam (long side) - 2 K2 Small roof top beam (short side) - 2 D2 Beam for short side - 2 E1 Decorative groove for long side - 2 E2 Decorative groove for short side - 2 E3 Decorative groove for corner - 4 F1 Slanting bar for large roof - 4 F2 Slanting bar for small roof - 4 G Middle bar for large roof - 4 H1 Lower beam connector 1-4 H2 Lower beam connector 2-4 I Lower middle beam connector - 4 L1 Big roof top short beam (short side) 1-2 L2 Big roof top short beam (short side) 2-2 L3 Big roof top long beam (short side) 1-2 L4 Big roof top long beam (short side) 2-2 M1 Big roof top short beam (long side) 1-2 M2 Big roof top short beam (long side) 2-2 M3 Big roof top long beam (long side) 1-2 M4 Big roof top long beam (long side) 2-2 N1 Small top roof cover - 1 N2 Small top cover for slanting bar - 4

5 5 N3 Big top cover for slanting bar - 4 O Connector for small top - 1 P Hook - 1 Q Wall - 1 Q1 Small roof cover (long side) - 2 Q2 Small roof cover (short side) - 2 W1 Small top roof panel (short side) - 2 W2 Small top roof panel (long side) - 2 X1 Big cover (long side) - 2 X2 Big top roof left big panel - 4 X3 Big top roof right big panel 2-4 X4 Big top roof left middle panel - 4 PARTS LIST R Mosquito netting - 1 R1 Big roof left cover - 4 R2 Big roof right cover - 4 R3 Big roof middle cover - 2 S Lower middle beam connector - 4 T Cutting sleeve - 4 U Baffle - 4 V Arc support - 8 X5 Big top roof right middle panel - 4 X6 Big top roof left small panel - 4 X7 Big top roof right small panel - 4 Y1 Left long pipe - 2 Y2 Right long pipe - 2 Y3 Left short pipe - 2 Y4 Right short pipe - 2

6 6 PRODUCT NO Spare Parts List M6X15 bolt - 80* M6X15 bolt - 4 M6 washer - 378* M6 washer - 19 PARTS LIST M6X15 screw - 160* M6X15 screw - 8 DD DD M6X25 screw - 16 M6X25 screw - 2 EE EE M6X45 bolt - 64 M6X45 bolt - 2 FF FF M6X55 screw - 28 M6X55 screw - 1 GG GG M6 nut - 28 M6 nut - 1 HH HH M6X40 screw - 18 M6X40 screw - 1 II Ф8X260 stake - 16 JJ Ring - 20 JJ Ring Z M6 wrench - 2 * Cumulative numbers of the hardware are listed in the manual.

7 7 CAUTION! Proper placement of the gazebo is essential. Do not place the product underneath electrical lines. Keep children under close supervision while they are playing around this product. This product contains small parts which can be swallowed by children. Keep fingers away from places where they can be pinched or trapped. Do not attempt to assemble the gazebo if any part is missing. Do not light any fires inside or near the product! Stay calm if fire breaks out. Search for the nearest exit. Do not return to the gazebo before firemen allow you to do so. GENERAL REQUIREMENTS Let us help you! DO NOT RETURN YOUR PRODUCT TO THE STORE. CALL US FIRST! If you have questions regarding your product, require warranty assistance, or have damaged or missing parts, please call our customer service toll-free helpline. Contact us for assistance; we re here to help. IMPORTANT: Please read and understand this manual before any assembly. Before beginning the assembly of product, make sure all parts are available. Compare parts list with packaging contents. If any part is missing, or if you have any questions, contact the service centre at (toll-free). Unpack and place all the parts from the packaging box in an open area and position them on the floor. Remove all packing materials and place them back into the box. Do not dispose of the packing materials until assembly is complete. Read each step carefully before beginning any assembly and make sure you understand each step. If you are missing a part, please call our tollfree number for assistance: Needed for assembly: Hammer Screwdriver Ladder 5 people

8 8 PRODUCT NO NOTE: When using screws and nuts to assemble the product, always use a flat washer between the frame and the screws and/or nuts. This will protect the parts from wear and tear. Step 1 Requires A, B, C,, (1a) Insert Post (A) into Base cover (C). A C (1b) Attach Base (B) to the bottom of Post (A) using M6x15 screw () and M6 washer (). Repeat the same procedure for the other bases. A C A B

9 9 Step 2 Requires D1, D2, T,, Slide the Cutting sleeve (T) into the centre of each Beam for long side (D1) and each Beam for short side (D2). Attach in the centre aligning the outer holes using M6x15 screws () and M6 washers (). T D1 D2 T D1 D2 Step 3 Requires A, D1, D2,, EE, Z Attach Beam for long side (D1) and Beam for short side (D2) to Posts (A) using M6x45 bolts (EE) and M6 washers (). Tighten the bolts using the wrench (Z). EE Z D1 A D2 D1 D2 A EE EE EE EE

10 10 PRODUCT NO Step 4 Requires A, H1,, DD Attach each Lower beam connector 1 (H1) to the top of each Post (A) using M6x25 screws (DD) and M6 washers (). DD DD DD H1 DD DD A D2 D1 Step 5 Requires E1, E2, E3,,, Z Insert Decorative groove for long side (E1) and Decorative groove for short side (E2) into each Decorative groove for corner (E3) using M6x15 bolts () and M6 washers (). Tighten the bolts using the wrench (Z). Z E3 E1 E2

11 11 Step 6 Requires E3, H1,,, Z Align the holes of the assembled Decorative grooves (E3) with the holes of the Lower beam connector 1s (H1). Attach the Decorative groove (E3) in all four corners to the Lower beam connector 1s (H1) using M6x15 bolts () and M6 washers (). Tighten the bolts using the wrench (Z). Z E3 H1 D1 D2 Step 7 Requires D1, D2, I,,, Z Attach the Lower middle beam connectors (I) to beams (D1, D2) using M6x15 bolts () and M6 washers (). Tighten the bolts using the wrench (Z). Z I D1 D2

12 12 PRODUCT NO Step 8 Requires A, V, D1, D2,, EE Attach the lower end of Arc supports (V) to Posts (A) and upper end of Arc supports (V) to beams (D1, D2) using M6x45 bolts (EE) and M6 washers (). EE Z A D1 D2 V EE Step 9 Requires J1, J2,,, Z Attach Frame for short side under big roofs (J2) to Frame for long side under big roofs (J1) using M6x15 bolts () and M6 washers (). Tighten the bolts using the wrench (Z). Z J1 J2

13 13 Step 10 Requires H2, J1, J2,,, Z Attach Lower beam connector 2s (H2) to Frame for long and small side under big roofs (J1, J2) using M6x15 bolts () and M6 washers (). Tighten the bolts using the wrench (Z). Z H2 J1 J2 Step 11 Requires F2, O,, FF, GG Attach one end of each Slanting bar for small roof (F2) to the Connector for small top (O) using M6x55 screws (FF), M6 washers () and M6 nuts (GG). Note: 2 single ends of the Slanting bar for small roof (F2) are attached to each end of the Connector for small top (O). FF GG O GG F2 FF

14 14 PRODUCT NO Step 12 Requires F2, H2,, FF, GG Attach Slanting bar for small roofs (F2) to lower beam connector 2s (H2) using M6x55 screws (FF), M6 washers () and M6 nuts (GG). FF GG FF GG H2 F2 Step 13 Requires F2, K1, K2,, Attach Small roof top beams (K1, K2) to Slanting bar for small tops (F2) using M6x15 screws () and M6 washers (). F2 K2 K1

15 15 Step 14 Requires O, P Attach Hook (P) to Connector for small top (O). O P Step 15 Requires F1, H1,, FF, GG Attach one end of Slanting bar for large roof (F1) to Lower beam connector 1 (H1) using M6x55 screws (FF), M6 washers () and M6 nuts (GG). FF GG F1 GG FF H1

16 16 PRODUCT NO Step 16 Requires G, I,, FF, GG Attach the lower end of Middle bar of large roofs (G) to Lower middle beam connectors (I) using M6x55 screws (FF), M6 washers () and M6 nuts (GG). FF GG GG G FF I Step 17 Requires E1, E2, G, S,,, Z Place the Lower middle beam connectors (S) into the slot on the Middle bar for large roofs (G) and Decorative grooves (E1, E2), then attach using M6x15 bolts () and M6 washers (). Tighten the bolts using the wrench (Z). Z S G E1 E2

17 17 Step 18 Requires F1, G, J1, J2,,, Z Place the assembled frame (J1, J2) over the Slanting bar for large roofs (F1), then attach the upper end of the Slanting bar for large roof (F1) to the corner of frame (J1, J2) using M6x15 bolts () and M6 washers (). Tighten the bolts using the wrench (Z). Z J2 J1 F1 Step 19 Requires G, J1, J2,,, Z Attach the upper end of the Middle bar for large roofs (G) to the middle of the frame (J1, J2) using M6x15 bolts () and M6 washers (). Tighten the bolts using the wrench (Z). Z J1 J2 G

18 18 PRODUCT NO Step 20 Requires G, L1, L2, M1, M2,, Attach one end of each beam (L1, L2, M1, M2,) to Middle bar for large roof (G) using M6x15 screws () and M6 washers (). G M1 L1 M2 L2 Step 21 Requires F1, L1, L2, L3, L4, M1, M2, M3, M4,, Attach other end of each beam (L1, L2, M1, M2) to Slanting bar for large roof (F1) using M6x15 screws () and M6 washers (). M1 L1 F1 M2 L2

19 19 Step 22 Requires G, L3, L4, M3, M4,, Attach one end of each beam (L3, L4, M3, M4) to Middle bar for large roofs (G) using M6x15 screws () and M6 washers (). G M3 L3 M4 L4 Step 23 Requires F1, L3, L4, M3, M4,, Attach other end of each beam (L3, L4, M3, M4) to Slanting bar for large roof (F1) using M6x15 screws () and M6 washers (). M3 L3 F1 M4 L4

20 20 PRODUCT NO Step 24 Requires G, Y1, Y2, Y3, Y4,, Attach one end of pipes (Y1, Y2, Y3, Y4) to Middle bar for large roof (G) using M6x15 screws () and M6 washers (). G Y2 Y4 Y1 Y3 Step 25 Requires F1, Y1, Y2, Y3, Y4,, Attach other end of pipes (Y1, Y2, Y3, Y4) to Slanting bar for large roof (F1) using M6x15 screws () and M6 washers (). F1 Y1 Y2 Y3 Y4

21 21 Step 26 Requires F2, W1, W2,, Attach Small top roof panels (W1, W2) to Slanting bar for small roof (F2) using M6x15 screws () and M6 washers (). W2 W1 Step 27 Requires N2,, HH Place Small top cover for slanting bars (N2) on Small top roof panels (W1, W2). Attach using M6x40 screws (HH) and M6 washers (). HH HH W2 HH N2 W1

22 22 PRODUCT NO Step 28 Requires N1,, HH Attach Small top roof cover (N1) to small top using M6x40 screws (HH) and M6 washers (). HH HH N1 HH Step 29 Requires K2, Q2,, Attach Small roof covers (Q2) to Small roof top beams (K2) using M6x15 screws () and M6 washers (). Q2 K2 W1

23 23 Step 30 Requires K1, Q1,, Attach Small roof covers (Q1) to Small roof top beams (K1) using M6x15 screws () and M6 washers (). Q1 K1 W2 Step 31 Requires J1, J2, X1, X2, X3, X4, X5, X6, X7 Attach Big cover (X1) to Big top roof big panel (X2) from right to left. Insert (X1, X2) into U shape on the frame (J1, J2). Repeat the same procedure and follow the callout sequence in figure below to attach all the other big top roof panels (X3, X4, X5, X6, X7). X6 X4 X3 X5 X7 X2 X2 X1 X3 X5 X7 X6 X2 X4 X2 X1 X1 J2

24 24 PRODUCT NO Step 32 Requires F1, X2, X3, X4, X5, X6, X7,, Attach the big top roof panels to Slanting bar for large roof (F1) using M6x15 screws () and M6 washers (). X6 X4 X2 X3 X5 X7 X3 X3 X5 X7 X6 X2 X4 X3 X2 X5 X4 X7 X6 Step 33 Requires N3,, HH Attach Big top cover for slanting bars (N3) to big top roof panels using M6x40 screws (HH) and M6 washers (). HH HH N3 HH

25 25 Step 34 Requires R1, R2, R3,, 34a) Attach Big roof left cover (R1) to the left end of gazebo using M6x15 screws () and M6 washers (). Similarly attach the Big roof right cover (R2) to the right end of the gazebo. 34b) Attach Big roof middle cover (R3) between covers (R1 & R2) on the long side using M6x15 screws () and M6 washers (). R1 X2 X4 X6 R1 R3 R2 R1 R2 R3 X1

26 26 PRODUCT NO Step 35 Requires D1, D2, U,, Attach each Baffle (U) to beams (D1, D2) using M6x15 screws () and M6 washers (). D1 U D2 A Step 36 Requires A, C, II If using on soil or grass, pull up the Base cover (C) and anchor the Post (A) to the ground using Stakes (II). Repeat this step for every post until all the posts are anchored. A C II II II B

27 27 Step 37 Requires R, Q, Y1, Y2, Y3, Y4, JJ Hang Mosquito netting (R) on the inner pipe of (Y1, Y2, Y3, Y4) using Rings (JJ). Hang Wall (Q) on the outer pipe of (Y1, Y2, Y3, Y4) using Rings (JJ). Attach Wall (Q) to the corner posts with strap to keep walls open. The gazebo is ready for use. JJ JJ Y1 Y2 Y3 Y4 Q R Q

28 28 PRODUCT NO SPECIFICATIONS CLEANING AND MAINTENANCE CAUTION! Check all screws and nuts periodically for tightness; fasten them as required. Disassemble the gazebo in reverse order of the steps used to assemble. Always disassemble the gazebo completely. A partially-disassembled gazebo is not stable enough to resist wind and bad weather, and therefore can be damaged and/or cause damage. Clean the gazebo gently with water using a sponge. Do not use abrasive materials, wire brushes, chemicals, cleansers or bleach. Do not use a pressure washer. Rinse well. Allow it to air dry. Steel components of garden accessories and furniture are treated with rust-inhibiting paint. However, due to the nature of steel, surface oxidation (rusting) will occur if this protective coating is scratched. This is a natural process. To minimize this condition, it is recommended to carefully assemble/ handle the product, in order to prevent the paint from being scratched. Surface rust can be removed easily using a very light application of common cooking oil. If surface oxidation (rusting) occurs and no measures are taken to correct it, the oxidation may start dripping onto the assembly surface, which may cause stains that may be difficult to remove. Dimensions (L x W x H) 12 x 10 x 10 1 Product weight 3.6 x 3 x 3.1 m 372 lbs 169 kg

29 29 This CANVAS product carries a three (3) year warranty against defects in workmanship and materials. Trileaf Distribution agrees to replace the defective product free of charge within the stated warranty period, when returned by the original purchaser with proof of purchase. This product is not guaranteed against wear or breakage due to misuse and/or abuse. WARRANTY