Connect Transit Shelter
|
|
- William King
- 5 years ago
- Views:
Transcription
1 Tools Required *denotes special tools required Connect Shelter, 8ft Connect Shelter, 12ft *Soft, non abrasive protective surface such as a furniture blanket *Source of compressed air (for thorough dust removal from anchor holes) Concrete anchor installation tools (for 5/8 11 concrete anchors or studs) *Hilti HIT HY 150 MAX adhesive system (or equal). *5/8 hole brush. Hilti HIT RB # and Manual Brush T handle # (or equal) Reciprocating saw with metal cutting blade or abrasive cutting wheel (for cutting 304SS anchor studs) File (to remove burrs and restore threads) *5/8 11 Die (to restore threads if required) *Glass cleaner suitable for glass panels such as Hope s Perfect Glass (or equal) Allen wrench set Security allen wrench set (Security bits included with hardware packs) Socket wrench set Utility knife Hammer Pry bar / nail puller *Spray bottle with soapy water *Furniture pads and or packaging materials *Squeegee *Paper toweling 4ft Level Tape measure *3 or 4 glass suction cup holders (sufficient to hold minimum weight of 110 lbs of glass each) *Glass handling safety equipment, including rubber gloves *Step ladders, scaffolding, or power lift equipment (sufficient to reach top of the Shelter with proper personnel support) GLASS STORAGE & HANDLING! The glass will arrive to the job site in one or more glass pallets. It is important to follow proper glass handling procedures for storage of the glass. Also, handling of the glass panels is potentially hazardous and care should be taken to insure safety of installation crew. ASSEMBLE WITH CARE! Pangard II Polyester Powdercoat is a strong, long lasting finish. To protect this finish during assembly, place unwrapped powdercoated parts on packaging foam or other non marring surface. Do not place or slide powdercoated parts on concrete or other hard or textured surface this will damage the finish causing rust to occur. Use touch up paint on any gouges in the finish caused by assembly tools. WARNING! SHELTER MUST BE SECURELY ANCHORED SO WIND DAMAGE CANNOT OCCUR. WIND DAMAGE COULD RESULT IN GLASS BREAKAGE AND POTENTIAL HARM TO PEOPLE. Landscape Forms is not responsible for site preparation and footings. We are including recommendations that you may consider. Page 1 of 15
2 Metro 40 - Connect Shelter - Footing Size / IBC Codes Buildin g Code Structural Approved Wind Load Snow Load Soil Pressure Concrete Footings Side Footing Size Rear / Front Footing Size Year State 3 sec. Gust Ground Allowable Concrete Re-Rod Wire Mesh D L W D L W 2006 MI 90 MPH 50 PSF 1,500 - PSF 3,000 - PSI 60,000 - PSI 65,000 - PSI 12" 7' 2' 12" 2' 2' 2007 MN 90 MPH 50 PSF 1,500 - PSF 3,000 - PSI 60,000 - PSI 65,000 - PSI 12" 7' 2' 12" 2' 2' 2007 FL 140 MPH 50 PSF 1,500 - PSF 3,000 - PSI 60,000 - PSI 65,000 - PSI 12" 8' 3' 12" 2' 2' 2007 FL 150 MPH 50 PSF 1,500 - PSF 3,000 - PSI 60,000 - PSI 65,000 - PSI 12" 10' 3'-9" 12" 2' 2' 40x 24x Optional Footings, Minimum sizes 20x H4 Anchor hardware pack 5/8 11 Threaded rod 5/8 11 Jam Nut 1 5/16 O.D. Washer 2x Mounting Plate Fig. 1.2.A STEP 1. Install anchors 1. Prepare site conditions to meet local building codes accordingly. 2. Set mounting plates in place. See Figure 1.2.B for 8ft shelter layout or Figure 1.2.C for 12ft shelter layout. NOTE: Mounting plate is not symmetric. See Figure 1.2.A for proper orientation. 3. Mark hole locations for mounting plates and optional front or rear glass locations as necessary. 4. Move plates anddrill drill holes. Useanchoringadhesive adhesive manufacturer srecommended recommended hole size. 5. Clear holes of debris. Fill with epoxy anchoring adhesive and set anchor rods. 6. After adhesive has properly cured, install leveling hex nuts on anchor rods. 7. Place mounting plate on hex nuts and adjust hex nuts until plate is level. NOTE: As sidewalks typically slope toward the street, at least one and perhaps both front leveling rods may be farther from the ground than back rods. The shelter can be set up to 1 1/2 off the ground and remain structural. If site conditions require anchoring rods to protrude more than 2 above ground, an additional concrete pier is required. Page 2 of 15
3 Fig. 1.2.B Connect Shelter, 8ft, Anchor Bolt Layout Fig. 1.2.C Connect Shelter, 12ft, Anchor Bolt Layout Page 3 of 15
4 Fig Front Frame Assembly Rear Frame Assembly 8x 8x H5 Cross member and rafter hardware pack 3/8 16 x 1 3/4 Socket Head Cap Screw 3/8 Washer STEP 2. Assemble frame structure 1. Remove access doors from horizontal beams and set aside. Retain hardware. 2. Assemble Horizontal Beams to Vertical Posts using H5 hardware as shown. Protect powdercoat finish during assembly. Page 4 of 15
5 40x 24x 20x H4 Anchor hardware pack 5/8 11 Threaded rod 5/8 11 Jam Nut 1 5/16 O.D. Washer Frame Assembly STEP 3. Install frames on mounting plate 1. Raise each frame into position and lower onto mounting plate. 2. Install washers and jam nuts from Hardware Pack H4 3. Each frame assembly weighs approximately 240lbs. Page 5 of 15
6 LED wiring Fig. 4.1 Duct Seal 8x 16x Rafter Assembly Fig H5 Cross member and rafter hardware pack 3/8 16 x 2 Threaded d rod 3/8 16 Internal threaded nut, hex Rafter with LED light Fig. 6 STEP 4. Install rafters. 1. Place 3/4 diameter ball of duct seal over the 1/2 diameter holes on the front horizontal beam as shown in Fig Outside rafters do not have LED lights. Middle rafters have an LED light. 3. Thread one mounting nut from Hardware Pack H5 onto the end of each threaded rod. 4. Raise rafter above frame assembly and lower onto brackets on horizontal beams. For middle rafters, feed wiring along rafter channel, then into the 1/2 diameter hole in the beam, eliminating wire slack as the rafter is lowered onto the bracket. 5. Insert threaded drod from Hardware Pack H5 to secure. 6. Install remaining mounting nut on opposite end of threaded rod. 7. Repeat for remaining rafters. STEP 5. Tighten hardware. After frame assembly is complete, tighten all fasteners and anchor nuts securely. Torque for 5/8 11 nuts is 90 ft. lbs. or 1100 in. lbs. STEP 6. Trim anchor studs. After hardware has been tightened, cut threaded anchor rods, leaving 1 2 full threads above the jam nut. Page 6 of 15
7 Wedge Gasket 2x Side Glass Panel 4x Glass retainer extrusion with glazing tape installed (2) 64 11/16 [1643mm] length (2) 72 3/16 [1834mm] length shipped installed Fig x Wedge gasket H6 Glass panel gasket pack Wedge gaskets Glazing tape 16x #10 24 x 3/4 Socket head cap screw, hex w/ pin, shipped installed Fig. 7.2 STEP 7. Install side glass panels. 1. Remove glass retainer extrusions, retaining hardware. 2. Install wedge gasket in all vertical extrusions that receive glass as shown in Fig Remove blue release film from glazing tape located on the vertical extrusions. Set side glass panel into frame, resting on the wedge gasket (side glass panel weighs 120lbs) 4. Align mounting holes in glass retainer extrusions. Remove the blue release film from the glazing gtape and install the retainer extrusion along the front edge using (4) #10 24 x 3/4 screws, as shown in Fig Repeat for rear edge. 5. Repeat for remaining side glass panel. Page 7 of 15
8 Fig. 8.3 Fig. 8.4 Fig x Gutter Extrusion Assembly 4x H1 Roof gasket pack EPDM gasket (washer) for flat head screw 4x H1 Roof glass and gutter retainer hardware pack 5/16 18 x 2 Flat head socket head cap screw STEP 8. Install Gutter Extrusion 1. Form (12) 1/4 diameter x 3 long pieces of duct seal. 2. Place duct seal in (3) places along each rafter one at each joint of rafter and horizontal beam, and one as indicated in Fig Remove end caps from gutter extrusion and set aside. Retain hardware. 4. Set gutter extrusion in place as shown. Install with (4) flat head socket cap screws and gaskets along the top row as shown in Fig If Solar option is specified, the solar panel is factory installed on the gutter extrusion. Page 8 of 15
9 Pre Wired LED Modules V Grid Wired Solar Power / Battery Power Fig. 8A.2 STEP 8A. Connect wiring (Line Voltage Option) 1. Run wiring as shown in Fig 8A.2 2. Connect the black wires from the LED luminaires to the black output wire from the LED driver. 3. Connect the red wires from the LED luminaires to the red output wire from the LED driver. 4. Connect the VAC input wires to the LED driver (follow local lcodes). red black Fig. 8A.4 battery Battery wiring diagram STEP 8A. Connect wiring (Solar Option only) 1. Solar panel is factory installed to the gutter extrusion. 2. Run wiring as shown in Fig. 8A.2 along rafter to connect to LED driver 3. Run battery jumper assembly and batteries with battery holders into Rear Horizontal Cross Member after connecting wiring harness to batteries. (16 batteries for 8ft shelter, 20 batteries for 12ft shelter.) 4. Connect wiring harness to lights and batteries and install vented access panels using security flat head #8 32 fasteners, as shown in Fig.8A.4. Solid access panels are installed along front horizontal beam. 5. Seal holes in horizontal beams with duct seal. Page 9 of 15
10 Fig. 9.1 Fig. 9.7 Right Center Left Roof Roof Roof Glass Glass Glass Fig x Rafter Plate with gasket 20x 20x 10x H1 Roof glass and gutter retainer hardware pack 5/16 18 x 1 1/2 socket button head cap screw White plastic glass spacer Black rubber washer STEP 9. Install Roof Glass 1. Install rafter gaskets on rafter. Middle rafters require the T shaped rubber gaskets. 2. Locate length of U gasket. Cut two pieces that are 60 17/32 long, and one piece that is 49 21/32 long. 3. Remove release paper from 60 17/32 long U gasket and adhere to back edge of end roof panel. 4. Place a 3/4 ball of duct seal at locations shown in Fig Wet the two rafter gaskets with soapy water. 6. Slide roof glass panel into gutter extrusion, aligning the (5) holes in the glass panel with the holes in the rafter. 7 Pl l ti i h l i l li ft l t ith h l ( k t id d ) and install rubber washer and socket button head cap screw as shown in Fig x Rafter 2x Rft Rafter 7. Place plastic spacers in holes in glass, align rafter plate with holes (gasket side down) T Gasket Gasket Page 10 of 15
11 Fig Fig Fig Fig STEP 9 (continued). Install Roof Glass 9. Remove release paper from 49 21/32 long U gasket and adhere to back edge of center roof panel. 10. Place a 3/4 ball of duct seal at locations shown in Fig Wet the two rafter gaskets with soapy water. 12. Slide center roof glass panel into gutter extrusion. 13. Align rafter plate with holes (gasket side down) and install rubber washer and socket button head cap screw as shown in Fig Place 3/4 ball of duct seal at locations shown in Fig Wet the rafter gaskets with soapy water. 16. Slide end roof glass panel into gutter extrusion, aligning the (5) holes in the glass panel with the holes in the rafter. 17. Align rafter plates with holes (gasket side down) and install hardware as shown in Fig Page 11 of 15
12 Fig Fig Fig x H1 Roof glass and gutter retainer hardware pack 5/16 18 x 2 Flat head socket head cap screw 4x H1 Roof gasket pack EPDM gasket (washer) for flat head screw 4x 2x Cover Plate Cover plate set screw 1/4 20 x 1/2 length set screw, hex drive, flat pt, factory installed STEP 10. Complete Gutter Installation 1. Install remaining (4) 5/16 18 x 2 flat head socket head cap screws and gaskets in gutter extrusion as shown in Fig Place 3/4 ball of duct seal at corners of glass and gutter extrusion as shown in Fig Remove release paper from gasket on gutter end cap. 4. Reattach gutter end caps using existing hardware as shown in Fig STEP 11. Cover Plate Installation 1. Set screws are factory installed in corner castings as shown in Fig Set cover plate in place. Insert hex key into holes in cover plate at two locations and loosen set screws until cover plate is fully engaged. Page 12 of 15
13 4x Glass upper block, installed Fig x Glass lower block 4x 4x H4 Anchor hardware pack 5/8 11 Jam Nut 1 5/16 OD O.D. Washer Fig Fig Fig STEP 12. Install Front and Rear Glass supports (if applicable) 1. Remove cover plate and retaining block from lower blocks, as shown in Fig. 12.1, and set aside, retaining hardware. Front and rear blocks are labeled accordingly. Remove glass retainer extrusions, retaining hardware. 2. Install lower glass blocks onto previously installed threaded rods, securing loosely with jam nuts and washers from hardware pack H4, as shown in Fig Upper glass blocks are factory installed. Remove retaining blocks from upper blocks and set aside. 4. Align edges of upper and lower glass blocks using a plumb line, as shown In Fig Align the glass support ledges on the lower blocks horizontally, as shown in Fig Page 13 of 15
14 Rear Left or Right Glass Front Left or Right Glass Rear Center Glass Front Center Glass Fig Fig x 4x Glass retainer extrusion with glazing tape installed (2) 64 11/16 [1643mm] length (rear) (2) 72 3/16 [1834mm] length (front) Shipped installed #10 24 x 3/4 Socket head cap screw, hex w/ pin Shipped installed Fig A Fig Fig B STEP 12 (continued). Install llfront and Rear Glass supports (if applicable) 6. Remove blue release film from glazing tape located on the vertical extrusions and glass retainer extrusions. 7. Set side glass panel into frame, resting on the wedge gasket and lower glass block support (rear side glass panel weighs 120lbs) as shown in Fig Install glass retainer extrusions using (4) #10 24 x 3/4 screws, as shown in Fig Repeat for remaining front and rear side glass panels, if applicable. 10. Set center glass panel in place as shown in Fig A. Spacing between glass panels should be equal, as shown in Fig B. 11. Reinstall retaining blocks using 1/4 20 X 1 screws as shown in Fig Page 14 of 15
15 Fig x Glass edge extrusion with glazing tape installed (2) 66 1/8 [1680mm] length (rear) (2) 73 3/4 [1873mm] length (front) Fig Fig STEP 12 (continued). Install Front and Rear Glass supports (if applicable) 12. Remove blue release film from glazing tape located on the glass edge extrusions. These extrusions are required for front and rear glass configurations that result in an exposed glass edge. 13. Install extrusion on glass panel as shown in Fig Set glass panel in position and install glass retaining blocks. 15. Install lower block cover plates as shown in Fig Page 15 of 15
INSTALLATION MANUAL FRONT. See pages 2 and 3 of this manual for configuration options. Level of Difficulty. Product Photo (center section only)
INSTALLATION MANUAL FRONT Level of Difficulty Moderate Product Photo (center section only) All hardware listed below will be provided with the bumpers center section. Additional hardware will be supplied
More informationFortress Fe Posts must always be secured to the deck framing. Fortress Fe Posts should never be attached to only the deck boards.
Installation Instructions for Fortress Horizontal Cable Panel System with UB-05 Brackets and Fe Posts It is the responsibility of the installer to meet all code and safety requirements, and to obtain all
More informationPickup Box Utility Rack Package Installation (Instruction ID: )
017 Chevrolet Colorado Pickup - WD (VIN S) Canyon, Colorado Accessory Installation Manual N America Document ID: 3966961 Pickup Box Utility Rack Package Installation (Instruction ID:3144879) Installation
More informationV nyl Gazebo truct c it Assembly Instr ons
V nyl Gazebo Vi Assembly Instr ct tr t u ru ons ct c i ti Pre-assembly Instructions A C B #1 - Site properly prepared. 4" - 6" clean stone 9 linear blocks 2" x 8" x 16" C C A A B B #1a - 12" sauna tubes,
More informationUSSC LLC 4 ONE LLC FIELD MODIFICATION INSTRUCTIONS
1 OF 17 A 1. PURPOSE: Instructions for in field replacement of 9004 mechanical suspension top pan 2. SCOPE: 9004 mechanical suspension with legacy two point LX back frame and current LX back frame 3. PROCEDURE:
More informationIntroduction. Rocky Mountain Westy Swing Away Carrier Kit Installation Instructions
Rocky Mountain Westy Swing Away Carrier Kit Installation Instructions Introduction Thank you for purchasing the Rocky Mountain Westy Swing Away Carrier Kit. We pride ourselves in the products we develop
More informationBumper Sign INSTALLATION INSTRUCTIONS
Bumper Sign INSTALLATION INSTRUCTIONS BUMPERSIGN TOOL CHECKLIST SDS MAX Rotary Hammer Drill Marker/Pencil SDS MAX 1 Carbide Drill Bit Tape Measure Torque Wrench with ½ Drive Power Source Vacuum ½ Drive
More informationFortress Fe Posts must always be secured to the deck framing. Fortress Fe Posts should never be attached to only the deck boards.
Installation Instructions for FortressCable H-Series Cable Panel System With UB-05 Brackets and Fe Posts It is the responsibility of the installer to meet all code and safety requirements, and to obtain
More informationKOLO SHELTER Installation Instructions Parts List
Parts List Roof Cap Rafter Upright Polycarbonate Polycarbonate Drop Polycarbonate Flange Center Weldment (Short length shown above) Polycarbonate Edge Bolt.25 x 6.5 Bolt.625 x 7.5 Threaded Rod.75 x 14
More informationSTRATUS SHELTER. Take bike parking to new heights
Take bike parking to new heights The Stratus Shelter is a striking bike shelter option for any transit station, university campus, or multi-family residential building project. It is constructed of American
More informationHoops Installation Instructions for Standard (Non-Adjustable) Basketball Goals
WARNING! Before beginning any excavation, call your local Underground Service Locator company to make sure there are NO electrical power, natural gas, telephone, cable television, irrigation systems or
More informationNOTE: Landscape Forms is not responsible for site preparation, footings, or electrical wiring.
11/2009 Stop Embedded Mount Bollard HANDLE WITH CARE! Pangard II Polyester Powder coat is a strong, long-lasting finish. Protect this finish from damage during installation. Place unwrapped powder coated
More informationInstallation Instructions for Vista Air Vertically Folding Walls
Installation Instructions for Vista Air Vertically Folding Walls Use these instructions in conjunction with your shop drawings to see the specifics that are particular to the model you are installing.
More informationIsuzu D-Max Part Numbers Black Polished
SB007 Sports Bar Fitting Instructions Isuzu D-Max 0 Part Numbers - 55000 - Black - 5000 - Polished Installation Time: 0 min (Approximately) PLEASE KEEP INSTRUCTIONS IN GLOVE BOX FOR FURTHER USE RECOMMENDED
More informationCSS Central Mount System
CSS-20 Installation Manual CSS-20 Safety Notifications Below are the installation instructions for the CSS-20-2 Long Span Beam Mounting System. Please read these safety notifications prior to beginning
More informationIndependent Containment System (ICS)
Installing the Independent Containment System (ICS) Complete these instructions to install the Independent Containment System (ICS). Prerequisites This installation requires a team of at least two people.
More informationFortress Fe Posts must always be secured to the deck framing. Fortress Fe Posts should never be attached to only the deck boards.
Installation Instructions for FortressCable H-Series Stair Panels with Simplified Stair Bracket SSB-05 and Fe Posts It is the responsibility of the installer to meet all code and safety requirements, and
More informationSB-WM-ART1-M-BL. Weatherproof Universal Single-Arm Articulating Mount for Medium Displays INSTALLATION MANUAL
SB-WM-ART1-M-BL Weatherproof Universal Single-Arm Articulating Mount for Medium Displays INSTALLATION MANUAL WARNING The maximum weight of this wall mount is 90 lbs (41 kg). Use with heavier than the maximum
More informationJEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT
JEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT FAJK001 / KRJW014T INSTALL TIME: 2.5 Hours NOTE: Your Jeep JK (5 Door) Extreme Roof Rack Kit consists of four boxes. (1) the Tray, (2) the Roll
More informationGared Pro-S Portable Backstop
Models: 9616 & 9618 Installation, Operation and Maintenance Instructions Please read all instructions before attempting installation or operation of these units SAVE THESE INSTRUCTIONS FOR FUTURE USE PUBLICATION
More informationPRODUCT: LOKI INSTALLATION INSTRUCTIONS. Product is covered by U.S. patents. For more information visit
R INSTALLATION INSTRUCTIONS PRODUCT: LOKI CONFIGURATION: SINGLE DOOR MOUNT: GLASS MOUNT Product is covered by U.S. patents. For more information visit www.krownlab.com . TOOLS + MATERIALS REQUIRED TOOLS
More informationINSTALLATION INSTRUCTIONS 10' WIDE FRAME FRAME SIZE: 10 X 18 X 7 (2 SQUARE TUBING) STORAGE SHELTER / CARPORT
INSTALLATION INSTRUCTIONS 10' WIDE FRAME FRAME SIZE: 10 X 18 X 7 (2 SQUARE TUBING) STORAGE SHELTER / CARPORT STORAGE SHELTER CARPORT Our unique assembly process quickly transforms the individual pieces
More informationIMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS
IMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS ** READ ALL INSTALLATION INSTRUCTIONS BEFORE STARTING!** If at any point, you have questions, call 1-800-851-0865...(The manufacturer will not be responsible
More informationINSTALLATION INSTRUCTIONS FOR PLASCORE F5075 FRAME WALL
INSTALLATION INSTRUCTIONS FOR PLASCORE F5075 FRAME WALL The following information is provided by Plascore, Inc., as a general guideline for the installation of the F5075 Frame Wall System. This information
More informationInstallation Instructions
Installation Instructions Follow these simple instructions to install your OneDayCab! IMPORTANT: Unpack and check shipment for damage. Verify color, size and parts before demolition. Installation of interiors
More information1. TOOLS + MATERIALS REQUIRED
R INSTALLATION INSTRUCTIONS PRODUCT: BALDUR + ODEN CONFIGURATION: BI-PARTING DOOR MOUNT: TOP MOUNT Product is covered by U.S. patents. For more information visit www.krownlab.com. TOOLS + MATERIALS REQUIRED
More informationP a r k c o n s o l e s i n k a s s e m b l y i n s t r u c t i o n s
P a r k c o n s o l e s i n k a s s e m b l y i n s t r u c t i o n s Before You Begin: Professional installation by two-person crew is required for this fixture. Install water supply and drain piping
More information7 X 10 X 6 SHELTER 7 X 16 X 6 SHELTER 12 X 10 X 6 SHELTER 12 X 16 X 6 SHELTER
ASSEMBLY INSTRUCTIONS FOR 7 X 10 X 6 AND 7 X 16 X 6 ATV SPORT SHELTER ACTUAL FRAME SIZES: 7 X 9-1 1/2 X 6 AND 7 X 13-7 1/2 X 6 AND 12 X 10 X 6 AND 12 X 16 X 6 ATV SPORT SHELTER ACTUAL FRAME SIZES: 12 X
More informationInstallation for Full Size Polaris Ranger Crew Doors
Installation for Full Size Polaris Ranger Crew Doors Order of Installation: Heater Doors Wiper on to Windshield Windshield Top & Back Panel Note: Most of the steps in these instructions need to be repeated
More information2010 KIDS CENTER #6 K-06
K-06 INSTALLATION GUIDELINES USER GROUP: 2-5 RECOMMENDED CREW: 2 people TOOLS REQUIRED: Tape measure Level High- speed 3/8 electric drill w/clutch NOTE: Use of any other driver may result in damage to
More informationFrameless Inline Door With Return QCI5263
INSTALLATION INSTRUCTIONS Frameless Inline Door With Return QCI5263 WALL MOUNT HINGES FRAMELESS DOOR / PANEL / RETURN PANEL QCI5263 REV. 0 Page 1 Certified 06/17/2016 Parts List with wall mount hinges
More informationHoops Installation Instructions for Adjustable Basketball Goals
WARNING! Before beginning any excavation, call your local Underground Service Locator company to make sure there are NO electrical power, natural gas, telephone, cable television, irrigation systems or
More informationSUPREME WALL GARDEN ASSEMBLY INSTRUCTIONS 24/08/16 www.hallsgreenhouses.com Please refer to website for the most up to date instructions. SAFETY WARNING 1. Always wear protective glasses, shoes, gloves
More informationRBP-1215B-RX DODGE RAM QUAD CAB RX3
RBP-1215B-RX3 2002-2017 DODGE RAM 15-3500 QUAD CAB RX3 Passenger side RX-3 Side Step Drill Template Passenger side rear Modular Bracket (6) L Support Brackets Driver side rear Modular Bracket Driver side
More informationFLOE DOCK FURNITURE WARNING ASSEMBLY INSTRUCTIONS
FLOE DOCK FURNITURE ASSEMBLY INSTRUCTIONS KIT P/N 510-00400-02 KIT P/N 510-00405-02 KIT P/N 510-00406-02 KIT P/N 510-00410-02 WARNING IT IS THE INSTALLER S RESPONSIBILITY TO PROPERLY INSTALL this chair
More informationUNIVERSAL INSTALLATION INSTRUCTIONS FOR CARPORTS
UNIVERSAL INSTALLATION INSTRUCTIONS FOR CARPORTS FRAME SIZES: WIDTH: 10, 12, 14, 16, 18, 20, 24, AND 30 ON CENTER FRAME SPACING: 4, 4 1/2, AND 5 FRAME LENGTH: 4 ON CENTER 20-2, 4 1/2 ON CENTER 18 AND 5
More informationIMPORTANT: PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE
IMPORTANT: PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE 005-07 Cadillac STS Classic 3D Z, Classic Dual Weave, Classic Mesh & Classic Black Mesh Grilles B 7 HR 3 STS Classic 3D Z Grille Part
More informationBollard CartMagnet Standard Open Unit INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Questions? Call McCue Customer Care at 800.800.8503 mccue.com The following installation instructions are provided for guidance only. The seller assumes no liability regarding
More informationFIXED SHOWER SCREEN For Wall Mount Hinges QCI5283
FIXED SHOWER SCREEN For Wall Mount Hinges QCI5283 QCI5283 Page 1 Date Certified: 06/16/2016 Parts List with wall mount clamp ITEM NO. DESCRIPTION QTY. 1 FIXED GLASS PANEL 1 2 WALL MOUNT CLAMP 1 3 U-CHANNEL
More informationEquilibrium. Conference Table. Installation Instruction. Revision B 11/07/16
Equilibrium Conference Table Installation Instruction Revision B 11/07/16 Equilibrium End User Agreement Enwork Equilibrium table bases must be installed directly onto a four inch minimum thickness concrete
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS R5 STEP BOARD APPLICATION: 2009-2017 Dodge Ram 1500 Quad / Crew Cab 2010-2017 Dodge Ram 2500/3500 Crew Cab PART NUMBER: 28-51040, 28-51045, 28-51050, 28-51055 ITEM QUANTITY DESCRIPTION
More informationSTYLE BAR & TONNEAU COVER INSTALLATION
STYLE BAR & TONNEAU COVER INSTALLATION INSTALLATION MANUAL: 2005 to '09 Mustang P/N: 10-8002-C12071B Saleen Performance, Inc. 1225 East Maple Rd., MI 48083 800-888-8945 www.saleen.com 1 IF YOU ARE NOT
More informationInstallation Manual for the Rockmeister Roof Ladder
Installation Manual for the Rockmeister Roof Ladder Exclusively for Mercedes-Benz Geländewagen W460, W461 & W463 with single rear door NOTE: W460 & W461 models have a different Frame Bracket than the W463.
More informationInstallation Guidelines
Page 1 Tools You ll Need 4 ft. Carpenter s level Chalk line (to mark U channel locations) Cordless drill/nut driver Caulking gun Chop saw with a metal cutting blade on it (required to make accurate and
More informationHorizontal Cable Systems
ALUMINUM RAILING INSTALLATION INSTRUCTIONS v2012 orizontal Cable Systems 1) Check Contents Of Packages: Verify that all parts have arrived and that they match the packing list. 1A) Coastal applications:
More informationTwo Panel Frameless Bypass Door
INSTALLATION INSTRUCTIONS Two Frameless Bypass Door Series 00 Please Record Model Number From Carton Label Here Please read these instructions carefully to familiarize yourself with the required tools,
More informationMTS-SP100. RENOGY Pole Mount System E Philadelphia St, Ontario, CA Version: 1.2
MTS-SP100 RENOGY Pole Mount System 2775 E Philadelphia St, Ontario, CA 91761 1-800-330-8678 1 Version: 1.2 Important Safety Instructions Please save these instructions. This manual contains important safety,
More informationMODULAR BUMPER INSTALLATION MANUAL
MODULAR BUMPER INSTALLATION MANUAL Parts List* 1 Center section 1 Side extension, passenger / right 1 Side extension, driver / left 1 Side cap, passenger / right 1 Side cap, driver / left 1 Brush guard,
More informationCARPORT INSTALLATION INSTRUCTIONS FOR 4 1/2 ON CENTER FRAMES
CARPORT INSTALLATION INSTRUCTIONS FOR 4 1/2 ON CENTER FRAMES FRAME SIZES: WIDTH: 12, 14, 18, 20, 24, AND 30 ON CENTER FRAME SPACING: 4 1/2 FRAME LENGTH: 18 EAVE HEIGHTS: START AT 7 TO 12 1/2. Our unique
More informationJEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT
JEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT FAJK002 / KRJW014T INSTALL TIME: 5 Hours NOTE: Your Jeep JK (5 Door) Extreme Roof Rack Kit consists of four boxes. (1) the Tray, (2) the Roll
More informationInstallation Instructions for Solar Snow Pad (SSP-T-3)
Installation Instructions for Solar Snow Pad (SSP-T-3) Warning- Do not use this product on solar arrays where the calculated array snow loads exceed 50 pounds per square foot (psf). Most solar panels are
More informationCertainTeed INSTALLATION GUIDE SIMTEK FENCE PRODUCTS. Fence Installation Guide 3', 4' & 6' High
CertainTeed INSTALLATION GUIDE SIMTEK FENCE PRODUCTS Fence Installation Guide 3', 4' & 6' High INSTALLATION GUIDE These instructions are designed to assist both professional installers and do-it-yourselfers
More informationFrameless Fixed Panel Slider
INSTALLATION INSTRUCTIONS Frameless Fixed Panel Slider QCI-5279 SINGLE ROLLER WITH ANTI-JUMP DOUBLE ROLLERS QCI5279 Rev Page Certified 08/09/6 Tools: To install your New Shower Enclosure, you may need
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More informationFrameless Inline Door QCI5254
INSTALLATION INSTRUCTIONS Frameless Inline Door QCI5254 FRAMELESS DOOR / PANEL QCI5254 REV. 0 Page 1 Cer fied 06/16/2016 Parts List with wall mount hinges *Quanes may vary QCI5254 REV. 0 Page 2 Cer fied
More informationDoor Canopy. PDL Building Products Industrial Parkway, N. Olmsted, OH Phone:
Door Canopy Door Canopies are attractive and efficient while eliminating the need and expense of drafting and manufacturing canopies as part of the building package. Construction: 26 gauge material around
More informationKO LO SH E LT E R. High Capacity and Flexibility
KO LO SH E LT E R High Capacity and Flexibility The unique styling of our redesigned Dero Kolo Shelter will help beautify your facility and provide secure, covered bike parking for cyclists. The Kolo is
More informationFrameless Inline Door QCI5248
INSTALLATION INSTRUCTIONS Frameless Inline Door QCI5248 FRAMELESS PANEL / DOOR / PANEL QCI5248 REV. 0 Page 1 Certified 06/16/2016 Parts List with glass to glass hinges *Quantities may vary. **Support Bar
More informationSolarWedge. Installation Manual Date Modified: 9/17/07 WARNING SAFETY. Tool List
APPLICATION: The product line provides an easy -to-install and economical solution for a 5, 10 or 15 degree tilted roof mounted system. integrates with Professional Solar s (ProSolar) patented top-down
More informationINSTALLATION INSTRUCTIONS LS X 12-2 X 7 1/2 FRAME LOAFING SHED
INSTALLATION INSTRUCTIONS LS-12 12 X 12-2 X 7 1/2 FRAME ACTUAL FRAME BASE SIZE: 12 X 12-2 LOAFING SHED Our unique assembly process quickly transforms the individual pieces into a finished structure that
More informationPRODUCT: BALDUR + ODEN
R INSTALLATION INSTRUCTIONS PRODUCT: BALDUR + ODEN CONFIGURATION: SINGLE DOOR MOUNT: GLASS MOUNT Product is covered by U.S. patents. For more information visit www.krownlab.com . TOOLS + MATERIALS REQUIRED
More informationFIXED PANEL SLIDER QCI5241
INSTALLATION INSTRUCTIONS FIXED PANEL SLIDER QCI5241 FRAMELESS PANEL / DOOR / PANEL FRAMELESS DOOR / PANEL QCI5241 REV. 0 Page 1 Certified 06/16/2016 Parts List *Quantities may vary QCI5241 REV. 0 Page
More informationCONTENTS TOOL LIST U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS. Revised: June 2013
U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS TOOL LIST Required Tools: - Reciprocating Saw with Metal Cutting Blade - Drill - 7/16 Drill Bit for Metal Drilling -
More information1. VERIFY ALL COMPONENTS
R INSTALLATION INSTRUCTIONS RAGNAR+ODEN FACE MOUNT, BYPASSING. VERIFY ALL COMPONENTS BASE KIT Track stand-offs Front trolley kit * Rear trolley kit * Allen keys Track fastener kit - wood - Bottom guide
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS LAMINATED P LASTIC TOILET PArTITIONS 1540 ClassicSeries with Options IMPORTANT: Storage and Handling Information on last page. For faster, easier installation, please review these
More informationEnclosed Partition Installation Instructions
Nissan NV1500/2500/3500 High Roof Partition Kit Part #: DTC 1502-036 V1.0.08.06.18 IMPORTANT INSTALLATION STEPS ARE DENOTED USING A STOP SIGN. THESE STEPS MUST BE PERFORMED IN THE SPECIFIED ORDER TO ENSURE
More informationEmagiKit. Privacy Pod Plus. Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY
EmagiKit Privacy Pod Plus Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY DIMENSIONS AND COMPONENTS 47 47 Ceiling Unit 2-B 2-L 2-R Glass Door Corner Trim Door Handle 90 Adjustable Height Work Surface 1-B
More information3/4 Rear DuraRac Installation Instructions
3/4 Rear DuraRac Installation Instructions Ford Transit Low Roof 130 WB Frame Kit Part #: CRC 27-1010-001 V1.0.09.28.18 IMPORTANT INSTALLATION STEPS ARE DENOTED USING A STOP SIGN. THESE STEPS MUST BE PERFORMED
More informationSmall Above Fireplace Pull-Down Full-Motion TV Wall Mount
Small Above Fireplace Pull-Down Full-Motion TV Wall Mount P/N 33123 User's Manual CONTENTS SAFETY WARNINGS AND GUIDELINES... 3 INTRODUCTION... 4 FEATURES... 4 CUSTOMER SERVICE... 4 PACKAGE CONTENTS...
More informationGiraud Tool Company, Inc.
Motor Upgrade for Gracey Trimmer This package is intended to allow the user to upgrade their Gracey trimmer with a higher rpm motor and convenience features not found in the production offering. This upgrade
More informationSteel Solutions USA 602 E. Walnut Street Watseka, IL p: (888) f: (815)
Steel Solutions USA 602 E. Walnut Street Watseka, IL 60970 p: (888) 875-5004 f: (815) 432-3364 sales@steelsolutionsusa.com Published February 2011 2011 Steel Solutions USA. All rights reserved. version
More informationAssembly Instructions Music Library System
Assembly Instructions Music Library System 7-Shelf Unit is shown. 6-Shelf Unit assembly is the same except where noted. Contents Important User Information...........................2 General...2 Manufacturer...2
More informationINSTALLATION INSTRUCTIONS LS X 12-2 X 7 1/2 FRAME LOAFING SHED
INSTALLATION INSTRUCTIONS LS-24 24 X 12-2 X 7 1/2 FRAME ACTUAL FRAME BASE SIZE: 24 X 12-2 LOAFING SHED Our unique assembly process quickly transforms the individual pieces into a finished structure that
More informationNext Level Security. This 2-tier locker ships flat to save on freight, comes in galvanized and powder coat finish options, and has a modular design.
T WO - T I E R B IK E LO C K E R Next Level Security We take long-term bicycle storage to new heights with the new Dero Two-Tier Bike Locker. It is easy to load and provides a space-saving solution to
More informationSB-WM-ART2-L-BL SB-WM-ART2-XL-BL
SB-WM-ART2-L-BL SB-WM-ART2-XL-BL Weatherproof Universal Dual-Arm Articulating Mount for Large TVs INSTALLATION MANUAL WARNING The maximum weight of this wall mount is 150 lbs (68.04 kg). Use with heavier
More informationCARPORT INSTALLATION INSTRUCTIONS FOR 4 1/2 ON CENTER FRAMES
CARPORT INSTALLATION INSTRUCTIONS FOR 4 1/2 ON CENTER FRAMES WIDTH: 10, 12, 14, 16, 18, 20, 24, AND 30 ON CENTER FRAME SPACING: 4 1/2 FRAME LENGTH: 18 EAVE HEIGHTS: START AT 7 TO 12 1/2. FRAME SIZES: Our
More informationInstallation Instruction
Tools Needed for Assembly Stud finder (for wood stud wall) Pencil Mark Electric drill Wood Stud Wall Installation Step 1. Locate the Wood Studs Installation Instruction Drill bit (for wood stud wall) Masonry
More informationIMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS FOR AZTEC SHELTER
IMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS FOR AZTEC SHELTER ** READ ALL INSTALLATION INSTRUCTIONS BEFORE STARTING!** If at any point, you have questions, call 1-800-851-0865...(The manufacturer will
More informationINSTALLATION INSTRUCTIONS LS X 12-2 X 7 1/2 FRAME LOAFING SHED
INSTALLATION INSTRUCTIONS LS-30 30 X 12-2 X 7 1/2 FRAME ACTUAL FRAME BASE SIZE: 30 X 12-2 LOAFING SHED Our unique assembly process quickly transforms the individual pieces into a finished structure that
More informationPORTA-FAB Cleanroom Wall Systems
PORTA-FAB Cleanroom Wall Systems FABLINE BATTEN 2000 INSTALLATION INSTRUCTIONS IMPORTANT Porta-Fab Advises A Thorough Reading of These Instructions Before Beginning Installation. INTRODUCTION Porta-Fab
More informationLAWN AND GARDEN GREENHOUSE
MODELS# OG0AL8-BKE OGAL-8 OGrow Walk-in ' x 8' LAWN AND GARDEN GREENHOUSE With Heavy Duty Aluminium Frame MANUAL VERSION # Grow r! e h t e g To Let's Thank you for purchasing the OGROW greenhouse Follow
More informationDura-Lock Roof System
DLR-14 Dura-Lock Roof System Assembly and Installation Instructions Read the instructions before starting the job. They explain the steps required to produce a finished product that will meet factory specifications.
More informationReal Life Ninja Complete Starter Pack (14ft. Warped Wall) Assembly Instructions
MATERIALS: 3 - Main Sections (Only 2 Sections for 10 ) 8 3 deck screws for joining sections inside of 2 Rock Wall Panels (with pre-installed t-nuts. Top panel comes with ladder mounting block preinstalled.)
More informationBe sure any accessory used will fit with the soft upper doors before installing. Not all accessories will be compatible.
Company Name: Spike Power Sports Vehicle Name: Polaris General 2P Product Description: Soft Upper Doors Part Number: 58-1600 Revision: R01 09/19/2018 Contents: 655 Elm Ridge Ave, Canal Fulton OH, 44614
More informationIMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS
IMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS ** READ ALL INSTALLATION INSTRUCTIONS BEFORE STARTING!** If at any point, you have questions, call 1-800-851-0865...(The manufacturer will not be responsible
More informationRear Mount Installation Instructions
Rear Mount Installation Instructions Ford Transit Low Roof 130 WB Frame Kit Part #: DTC 0809-011 V1.0.10.12.18 IMPORTANT INSTALLATION STEPS ARE DENOTED USING A STOP SIGN. THESE STEPS MUST BE PERFORMED
More informationTREX PERGOLA INSTALLATION INSTRUCTIONS
RECOMMENDED TOOLS/SUPPLIES: Pencil 4' Level Measuring Tape Framing Square/Speed Square 8' High Step Ladder (Two recommended) Hacksaw or Bolt Cutters Socket Wrench with 9/16" Socket and 3/4" Deep Socket
More informationINSTALLATION INSTRUCTIONS SUBURBAN SERIES CARPORT 25 X 20 X 6 LENGTH CAN BE EXTENDED IN 4 1/2 INCREMENTS HEIGHT CAN BE EXTENDED IN 1 INCREMENTS
INSTALLATION INSTRUCTIONS SUBURBAN SERIES CARPORT 25 X 20 X 6 LENGTH CAN BE EXTENDED IN 4 1/2 INCREMENTS HEIGHT CAN BE EXTENDED IN 1 INCREMENTS BASIC FRAME SIZES (NO EXTENSIONS): 25-1/2 X 18' x 6 EAVE
More informationINSTALLATION INSTRUCTIONS CONTOURED LIGHT BAR APPLICATION: CHEVY EQUINOX/ GMC TERRAIN PART NUMBERS: ,
INSTALLATION INSTRUCTIONS CONTOURED LIGHT BAR APPLICATION: 2010-2014 CHEVY EQUINOX/ GMC TERRAIN PART NUMBERS: 32-21020, 32-21025 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 CONTOUR BAR TORQUE WRENCH 2 1
More informationPreference Collection 5543 Central Console INSTALLATION GUIDE
Preference Collection 5543 Central Console INSTALLATION GUIDE WARNING Failure to install the 5543 as described in this installation guide may cause the unit to collapse, resulting in serious injury to
More informationPARTITION INSTALLATION INSTRUCTIONS
PARTITION INSTALLATION INSTRUCTIONS 2015 Chevrolet Tahoe PPV / Part Number 5703FW, FWA & FEW Do not attempt to install this product on any vehicle equipped with third row seating! Parts List Distributed
More informationFootball Goal Posts MODEL SERIES: FGP400 and FGP600 series
Football Goal Posts MODEL SERIES: FGP400 and FGP600 series Installation and Maintenance Instructions Please read all instructions before attempting installation of these units SAVE THESE INSTRUCTIONS FOR
More informationPL-91. Frameless Door with Panel. 202 Anderson Ave., Belvue, KS Phone: Fax:
202 Anderson Ave., Belvue, KS 66407 Phone: 800-669-9867 Fax: 800-393-6699 www.onyxcollection.com 800-643-1514 www.alumaxshowerdoor.com PL-91 Frameless Door with Panel Full Showers Bench Seat Showers PL91-0318
More informationWARNING!! DO NOT LIFT DOORS UP WHEN THE HOOD IS OPEN. THE DOORS WILL HIT THE HOOD!
WARNING!! DO NOT LIFT DOORS UP WHEN THE HOOD IS OPEN. THE DOORS WILL HIT THE HOOD! THIS KIT INCLUDES: 4 M8-1.25X30MM BOLTS WITH WASHERS 12 M8-1.25X40MM BOLTS WITH WASHERS 2 SHOULDER BOLTS WITH RIGHT AND
More informationASSEMBLY INSTRUCTIONS FOR SOFTOP SHADE COVER
ASSEMBLY INSTRUCTIONS FOR SOFTOP SHADE COVER Our unique assembly process quickly transforms individual pieces into a finished structure that will give you a lifetime of service. Great care has been taken
More informationINSTALLATION INSTRUCTIONS 12' x 18' x 7' FRAME (12 x 20 x 7 ROOF COVERAGE) 2 SQUARE CARPORT
INSTALLATION INSTRUCTIONS 12' x 18' x 7' FRAME (12 x 20 x 7 ROOF COVERAGE) 2 SQUARE CARPORT Our unique assembly process quickly transforms the individual pieces into a finished structure that will give
More informationReal Life Ninja Starter Pack 1 Assembly Instructions
Real Life Ninja Starter Pack 1 Assembly Instructions MATERIALS: Warped Wall 3 - Main Sections (Only 2 Sections for 10 Warped Wall) 8 3 deck screws for joining sections inside of Warped Wall 2 Rock Wall
More informationKawasaki Teryx 750 Cab Kit* Caution: Before using this product, read this manual and follow all Safety Instructions.
Owner s Manual Model: Kawasaki Teryx 750 Kawasaki Teryx 750 Cab Kit* Caution: Before using this product, read this manual and follow all Safety Instructions. Safety Instructions Cab Kit Contents Hardware
More informationPLAYLAND 72 SPIRAL SLIDE 3.5 Posts, 3.5 Posts / 48 Grid and 5 Posts
PLAYLAND 72 SPIRAL SLIDE 3.5 Posts, 3.5 Posts / 48 Grid and 5 Posts USER GROUP: 2-12 RECOMMENDED CREW: 2 people TOOLS REQUIRED: T-30 TORX tool (supplied by manufacturer) T-45 TORX tool (supplied by manufacturer)
More information