Enhanced Low Dose Rate Sensitivity (ELDRS) Radiation Testing of the RH1814MW Quad Op Amp for Linear Technology

Transcription

1 Enhanced Low Dose Rate Sensitivity (ELDRS) Radiation Testing of the RH1814MW Quad Op Amp for Linear Technology Customer: Linear Technology (PO 57472L) RAD Job Number: Part Type Tested: Linear Technology RH1814MW Quad Op Amp Commercial Part Number: RH1814MW Traceability Information: Fab Lot# WF , Wafer# 2, Assembly Lot# Information obtained from Linear Technology PO#57472L. Date code marking on the package is 1024A, see Appendix A for a photograph of the device and part markings. Quantity of Units: 12 units total, 5 units for biased irradiation, 5 units for unbiased irradiation and 2 control units. Serial numbers 295 to 298 and 300 were biased during irradiation, serial numbers 301, 302, 304 to 306 were unbiased during irradiation and serial numbers 307 and 308 were used as the controls. See Appendix B for the radiation bias connection table. External Traveler: None Required Pre-Irradiation Burn-In: Burn-In performed by Linear Technology prior to receipt by RAD. TID Dose Rate and Test Increments: 10mrad(Si)/s with readings at pre-irradiation, 10, 20, 30, 40, and 50 krad(si). TID Overtest and Post-Irradiation : No overtest. 24-hour room temperature anneal followed by a 168- hour 100 C anneal. Both anneals shall be performed in the same electrical bias condition as the irradiations. Electrical measurements shall be made following each anneal increment. TID Test Standard: MIL-STD-883H, Method , Condition D TID Electrical Test Conditions: Pre-irradiation, and within one hour following each radiation exposure. Hardware and Software: LTS2020 Automated Tester, Entity ID TS04, Calibration Date: , Calibration Due LTS2101 Family Board, Entity ID FB02. LTS0600 Test Fixture, Entity ID TF03. RH1814W BGSS DUT Board. Test Program: RH1814W.SRC Facility and Radiation Source: Longmire Laboratories, Colorado Springs, CO using the GB-150 low dose rate Co60 source. Dosimetry performed by Air Ionization Chamber (AIC) traceable to NIST. RAD s dosimetry has been audited by DSCC and RAD has been awarded Laboratory Suitability for MIL- STD-750 TM Irradiation and Test Temperature: Ambient room temperature for irradiation and test controlled to 24 C ± 6 C per MIL-STD-883. Low Dose Rate Test Result: PASSED. The units showed no significant degradation with total dose. All parameters remained within their datasheet specifications to the maximum dose level tested of 50krad(Si). Further the units do not exhibit ELDRS as defined in the current test method. 1

2 1.0. Overview and Background It is well known that total dose ionizing radiation can cause parametric degradation and ultimately functional failure in electronic devices. The damage occurs via electron-hole pair production, transport and trapping in the dielectric regions. In advanced CMOS technology nodes (0.6µm and smaller) the bulk of the damage is manifested in the thicker isolation regions, such as shallow trench or local oxidation of silicon (LOCOS) oxides (also known as "birds-beak" oxides). However, many linear and mixed signal devices that utilize bipolar minority carrier elements exhibit an enhanced low dose rate sensitivity (ELDRS). At this time there is no known or accepted a priori method for predicting susceptibility to ELDRS or simulating the low dose rate sensitivity with a "conventional" room temperature rad(Si)/s irradiation (Condition A in MIL-STD-883 TM ). Over the past 10 years a number of accelerating techniques have been examined, including an elevated temperature anneal, such as that used for MOS devices (see ASTM-F-1892 for more technical details) and irradiating at various temperatures. However, none of these techniques have proven useful across the wide variety of linear and/or mixed signal devices used in spaceborne applications. The latest requirement incorporated in MIL-STD-883 TM 1019 requires that devices that could potentially exhibit ELDRS "shall be tested either at the intended application dose rate, at a prescribed low dose rate to an overtest radiation level, or with an accelerated test such as an elevated temperature irradiation test that includes a parameter delta design margin". While the recently released MIL-STD- 883 TM 1019 allows for accelerated testing, the requirements for this are to essentially perform a low dose rate ELDRS test to verify the suitability of the acceleration method on the component of interest before the acceleration technique can be instituted. Based on the limitations of accelerated testing and to meet the requirements of MIL-STD-883 TM Condition D, we have performed a low dose rate test at 10mrad(Si)/s Radiation Test Apparatus The low dose rate testing described in this final report was performed using the facilities at Radiation Assured Devices' Longmire Laboratories in Colorado Springs, CO. The low dose rate source is a GB- 150 irradiator modified to provide a panoramic exposure. The Co-60 rods are held in the base of the irradiator heavily shielded by lead. During the irradiation exposures the rod is raised by an electronic timer/controller and the exposure is performed in air. The dose rate for this irradiator in this configuration ranges from approximately 1mrad(Si)/s to a maximum of approximately 50rad(Si)/s, determined by the distance from the source. For low dose rate testing described in this report, the devices are placed approximately 2-meters from the Co-60 rods. The irradiator calibration is maintained by ' Longmire Laboratories using air ionization chamber (AIC) dosimetry traceable to the National Institute of Standards and Technology (NIST). Figure 2.1 shows a photograph of the GB-150 Co-60 irradiator at RAD's Longmire Laboratory facility. 2

3 Figure 2.1. ' Co-60 irradiator. The dose rate is obtained by positioning the device-under-test at a fixed distance from the gamma cell. The dose rate for this irradiator varies from approximately 50rad(Si)/s close to the rods down to <1mrad(Si)/s at a distance of approximately 4-meters. 3

4 3.0. Radiation Test Conditions The RH1814MW Quad Operational Amplifier described in this final report was irradiated using a split 5V supply and with all pins tied to ground, that is biased and unbiased. See Appendix B for details on the biasing conditions during radiation exposure. In our opinion, this bias circuit satisfies the requirements of MIL-STD-883H TM Section Bias and Loading Conditions which states "The bias applied to the test devices shall be selected to produce the greatest radiation induced damage or the worst-case damage for the intended application, if known. While maximum voltage is often worst case some bipolar linear device parameters (e.g. input bias current or maximum output load current) exhibit more degradation with 0 V bias." The devices were irradiated to a maximum total ionizing dose level of 50krad(Si) with incremental readings at 10krad(Si), 20krad(Si), 30krad(Si) and 40krad(Si). Electrical testing occurred within one hour following the end of each irradiation segment. For intermediate irradiations, the units were tested and returned to total dose exposure within two ours from the end of the previous radiation increment. The radiation exposure bias board was positioned in the Co-60 cell to provide the targeted dose rate of 10mrad(Si)/s and was located inside a lead-aluminum enclosure. The lead-aluminum enclosure is required under MIL-STD-883H TM Section 3.4 that reads as follows: "Lead/Aluminum (Pb/Al) container. Test specimens shall be enclosed in a Pb/Al container to minimize dose enhancement effects caused by low-energy, scattered radiation. A minimum of 1.5 mm Pb, surrounding an inner shield of at least 0.7 mm Al, is required. This Pb/Al container produces an approximate charged particle equilibrium for Si and for TLDs such as CaF2. The radiation field intensity shall be measured inside the Pb/Al container (1) initially, (2) when the source is changed, or (3) when the orientation or configuration of the source, container, or test-fixture is changed. This measurement shall be performed by placing a dosimeter (e.g., a TLD) in the device-irradiation container at the approximate test-device position. If it can be demonstrated that low energy scattered radiation is small enough that it will not cause dosimetry errors due to dose enhancement, the Pb/Al container may be omitted". The final dose rate within the lead-aluminum box was determined based on TLD dosimetry measurements just prior to the beginning of the total dose irradiations. The final dose rate for this work was 10mrad(Si)/s with a precision of ±5%. 4

5 4.0. Tested Parameters During the radiation lot acceptance testing the following pre- and post-irradiation electrical parameters were measured: 1. Positive Supply Current 2. Negative Supply Current 3. Input Offset Voltage (Op Amp 1-4) 4. Input Offset Current (Op Amp 1-4) 5. + Input Bias Current (Op Amp 1-4) 6. - Input Bias Current (Op Amp 1-4) 7. CMRR (Op Amp 1-4) 8. PSRR (Op Amp 1-4) 9. Large Signal Voltage Gain RL=500 (Op Amp 1-4) 10. Large Signal Voltage Gain RL=100 (Op Amp 1-4) 11. Channel Separation (Op Amp 1-4, all permutations) 12. Output Voltage Swing High RL=500 (Op Amp 1-4) 13. Output Voltage Swing High RL=100 (Op Amp 1-4) 14. Output Voltage Swing Low RL=500 (Op Amp 1-4) 15. Output Voltage Swing Low RL=100 (Op Amp 1-4) 16. Maximum Output Source Current (Op Amp 1-4) 17. Maximum Output Sink Current (Op Amp 1-4) 18. Positive Short-Circuit Current (Op Amp 1-4) 19. Negative Short-Circuit Current (Op Amp 1-4) The parametric data was obtained as "read and record" and all the raw data plus an attributes summary are contained in this report as well as in a separate Excel file. The attributes data contains the average, standard deviation and the average with the KTL values applied. The KTL value used in this work is per MIL-HDBK-814 using one sided tolerance limits of 90/90 and a 5-piece sample size. The 90/90 KTL values were selected to match the statistical levels specified in the MIL-PRF sampling plan for the qualification of a radiation hardness assured (RHA) component. Note that the following criteria must be met for a device to pass the low dose rate test: following the radiation exposure each of the 5 pieces irradiated under electrical bias shall pass the specification value. The units irradiated without electrical bias and the KTL statistics are included in this report for reference only. If any of the 5 pieces irradiated under electrical bias exceed the datasheet specifications, then the lot could be logged as a failure. Further, MIL-STD-883H, TM Section Characterization test to determine if a part exhibits ELDRS' states the following: Select a minimum random sample of 21 devices from a population representative of recent production runs. Smaller sample sizes may be used if agreed upon between the parties to the test. All of the selected devices shall have undergone appropriate elevated temperature reliability screens, e.g. burn-in and high temperature storage life. Divide the samples into 5

6 four groups of 5 each and use the remaining part for a control. Perform pre-irradiation electrical characterization on all parts assuring that they meet the Group A electrical tests. Irradiate 5 samples under a 0 volt bias and another 5 under the irradiation bias given in the acquisition specification at rad(si)/s and room temperature. Irradiate 5 samples under a 0 volt bias and another 5 under irradiation bias given in the acquisition specification at < 10mrad(Si)/s and room temperature. Irradiate all samples to the same dose levels, including 0.5 and 1.0 times the anticipated specification dose, and repeat the electrical characterization on each part at each dose level. Post irradiation electrical measurements shall be performed per paragraph 3.10 where the low dose rate test is considered Condition D. Calculate the radiation induced change in each electrical parameter ( para) for each sample at each radiation level. Calculate the ratio of the median para at low dose rate to the median para at high dose rate for each irradiation bias group at each total dose level. If this ratio exceeds 1.5 for any of the most sensitive parameters then the part is considered to be ELDRS susceptible. This test does not apply to parameters which exhibit changes that are within experimental error or whose values are below the pre-irradiation electrical specification limits at low dose rate at the specification dose. Therefore, the data in this report can be analyzed along with the high dose rate report titled "Total Ionizing Dose (TID) Radiation Testing of the RH1814MW Quad Op Amp for Linear Technology" to demonstrate that these parts do not exhibit ELDRS as defined in the current test method. 6

7 5.0. ELDRS Test Results Based on this criterion the RH1814MW Quad Operational Amplifier (from the lot date code identified on the first page of this test report) PASSED the enhanced low dose rate sensitivity test to the maximum tested dose level of 50krad(Si) with all parameters remaining within their datasheet specifications. Figures 5.1 through show plots of all the measured parameters versus total ionizing dose while Tables show the corresponding raw data for each of these parameters. In the data plots the solid diamonds are the average of the measured data points for the sample irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the units irradiated with all pins tied to ground. The black lines (solid or dashed) are the average of the data points after application of the KTL statistics on the sample irradiated in the biased condition while the shaded lines (solid or dashed) are the average of the data points after application of the KTL statistics on the sample irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. In addition to the radiation test results, the data plots and tables described above contain anneal data. The anneals are performed to better understand the underlying physical mechanisms responsible for radiation-induced parametric shifts and are not part of the criteria used to establish whether or not the lot passes or fails the low dose rate test. In all cases the parts either improved or exhibited no change during the anneal. The control units, as expected, show no significant changes to any of the parameters. Therefore we can conclude that the electrical testing remained in control throughout the duration of the tests and the observed degradation was due to the radiation exposure. Appendix D lists the figures used in this section to facilitate the location of a particular parameter. 7

8 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX 1.50E-02 Positive Supply (A) 1.45E E E E E E E hr hr 70 Figure 5.1. Plot of Positive Supply (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 8

9 Table 5.1. Raw data for Positive Supply (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Supply (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased 1.27E E E E E E E E-02 Std Dev Biased 3.41E E E E E E E E-04 Ps90%/90% (+KTL) Biased 1.37E E E E E E E E-02 Ps90%/90% (-KTL) Biased 1.18E E E E E E E E-02 Un-Biased Statistics Average Un-Biased 1.23E E E E E E E E-02 Std Dev Un-Biased 7.72E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 1.44E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased 1.01E E E E E E E E-02 Specification MAX 1.44E E E E E E E E-02 Status PASS PASS PASS N/A N/A PASS PASS PASS 9

10 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN -1.20E-02 Negative Supply (A) -1.25E E E E E E hr hr 70 Figure 5.2. Plot of Negative Supply (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 10

11 Table 5.2. Raw data for Negative Supply (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Supply (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased -1.28E E E E E E E E-02 Std Dev Biased 3.42E E E E E E E E-04 Ps90%/90% (+KTL) Biased -1.18E E E E E E E E-02 Ps90%/90% (-KTL) Biased -1.37E E E E E E E E-02 Un-Biased Statistics Average Un-Biased -1.23E E E E E E E E-02 Std Dev Un-Biased 7.71E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased -1.02E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased -1.44E E E E E E E E-02 Specification MIN -1.44E E E E E E E E-02 Status PASS PASS PASS N/A N/A PASS PASS PASS 11

12 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 5.00E-03 Input Offset #1 (V) 4.00E E E E E E E E E E hr hr 70 Figure 5.3. Plot of Input Offset #1 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 12

13 Table 5.3. Raw data for Input Offset #1 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset #1 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-06 Biased Statistics Average Biased -1.75E E E E E E E E-04 Std Dev Biased 3.27E E E E E E E E-04 Ps90%/90% (+KTL) Biased 7.22E E E E E E E E-04 Ps90%/90% (-KTL) Biased -1.07E E E E E E E E-03 Un-Biased Statistics Average Un-Biased -9.86E E E E E E E E-04 Std Dev Un-Biased 4.93E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 1.25E E E E E E E E-03 Ps90%/90% (-KTL) Un-Biased -1.45E E E E E E E E-03 Specification MIN -1.50E E E E E E E E-03 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 1.50E E E E E E E E-03 Status PASS PASS PASS N/A N/A PASS PASS PASS 13

14 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 5.00E-03 Input Offset #2 (V) 4.00E E E E E E E E E E hr hr 70 Figure 5.4. Plot of Input Offset #2 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 14

15 Table 5.4. Raw data for Input Offset #2 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset #2 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-04 Biased Statistics Average Biased -2.47E E E E E E E E-04 Std Dev Biased 3.66E E E E E E E E-04 Ps90%/90% (+KTL) Biased 7.57E E E E E E E E-04 Ps90%/90% (-KTL) Biased -1.25E E E E E E E E-03 Un-Biased Statistics Average Un-Biased -1.35E E E E E E E E-04 Std Dev Un-Biased 2.19E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 4.66E E E E E E E E-04 Ps90%/90% (-KTL) Un-Biased -7.36E E E E E E E E-04 Specification MIN -1.50E E E E E E E E-03 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 1.50E E E E E E E E-03 Status PASS PASS PASS N/A N/A PASS PASS PASS 15

16 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 5.00E-03 Input Offset #3 (V) 4.00E E E E E E E E E E hr hr 70 Figure 5.5. Plot of Input Offset #3 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 16

17 Table 5.5. Raw data for Input Offset #3 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset #3 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-04 Biased Statistics Average Biased -2.03E E E E E E E E-04 Std Dev Biased 5.75E E E E E E E E-04 Ps90%/90% (+KTL) Biased 1.37E E E E E E E E-03 Ps90%/90% (-KTL) Biased -1.78E E E E E E E E-03 Un-Biased Statistics Average Un-Biased -1.78E E E E E E E E-04 Std Dev Un-Biased 3.06E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 6.62E E E E E E E E-04 Ps90%/90% (-KTL) Un-Biased -1.02E E E E E E E E-03 Specification MIN -1.50E E E E E E E E-03 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 1.50E E E E E E E E-03 Status PASS PASS PASS N/A N/A PASS PASS PASS 17

18 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 5.00E-03 Input Offset #4 (V) 4.00E E E E E E E E E E hr hr 70 Figure 5.6. Plot of Input Offset #4 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 18

19 Table 5.6. Raw data for Input Offset #4 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset #4 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-04 Biased Statistics Average Biased -1.27E E E E E E E E-04 Std Dev Biased 1.83E E E E E E E E-04 Ps90%/90% (+KTL) Biased 3.74E E E E E E E E-04 Ps90%/90% (-KTL) Biased -6.29E E E E E E E E-04 Un-Biased Statistics Average Un-Biased 1.68E E E E E E E E-04 Std Dev Un-Biased 2.35E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 8.12E E E E E E E E-04 Ps90%/90% (-KTL) Un-Biased -4.75E E E E E E E E-04 Specification MIN -1.50E E E E E E E E-03 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 1.50E E E E E E E E-03 Status PASS PASS PASS N/A N/A PASS PASS PASS 19

20 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 1.00E-06 Input Offset #1 (A) 8.00E E E E E E E E E E hr hr 70 Figure 5.7. Plot of Input Offset #1 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 20

21 Table 5.7. Raw data for Input Offset #1 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset #1 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-08 Biased Statistics Average Biased 1.23E E E E E E E E+00 Std Dev Biased 5.07E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.51E E E E E E E E+00 Ps90%/90% (-KTL) Biased -1.27E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 1.30E E E E E E E E-09 Std Dev Un-Biased 6.09E E E E E E E E-09 Ps90%/90% (+KTL) Un-Biased 1.80E E E E E E E E-08 Ps90%/90% (-KTL) Un-Biased -1.54E E E E E E E E-08 Specification MIN -4.00E E E E E E E E-07 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-07 Status PASS PASS PASS N/A N/A PASS PASS PASS 21

22 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 1.00E-06 Input Offset #2 (A) 8.00E E E E E E E E E E hr hr 70 Figure 5.8. Plot of Input Offset #2 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 22

23 Table 5.8. Raw data for Input Offset #2 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset #2 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 2.11E E E E E E E E-09 Std Dev Biased 9.95E E E E E E E E-08 Ps90%/90% (+KTL) Biased 2.94E E E E E E E E-08 Ps90%/90% (-KTL) Biased -2.52E E E E E E E E-08 Un-Biased Statistics Average Un-Biased 9.56E E E E E E E E+00 Std Dev Un-Biased 4.72E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.39E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased -1.20E E E E E E E E+00 Specification MIN -4.00E E E E E E E E-07 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-07 Status PASS PASS PASS N/A N/A PASS PASS PASS 23

24 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 1.00E-06 Input Offset #3 (A) 8.00E E E E E E E E E E hr hr 70 Figure 5.9. Plot of Input Offset #3 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 24

25 Table 5.9. Raw data for Input Offset #3 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset #3 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-08 Biased Statistics Average Biased 2.00E E E E E E E E+00 Std Dev Biased 2.35E E E E E E E E+00 Ps90%/90% (+KTL) Biased 8.46E E E E E E E E+00 Ps90%/90% (-KTL) Biased -4.45E E E E E E E E+00 Un-Biased Statistics Average Un-Biased -1.19E E E E E E E E+00 Std Dev Un-Biased 3.82E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 9.29E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased -1.17E E E E E E E E+00 Specification MIN -4.00E E E E E E E E-07 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-07 Status PASS PASS PASS N/A N/A PASS PASS PASS 25

26 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 1.00E-06 Input Offset #4 (A) 8.00E E E E E E E E E E hr hr 70 Figure Plot of Input Offset #4 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 26

27 Table Raw data for Input Offset #4 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset #4 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 3.95E E E E E E E E-09 Std Dev Biased 1.08E E E E E E E E-09 Ps90%/90% (+KTL) Biased 3.36E E E E E E E E-08 Ps90%/90% (-KTL) Biased -2.57E E E E E E E E-08 Un-Biased Statistics Average Un-Biased 8.87E E E E E E E E-09 Std Dev Un-Biased 1.12E E E E E E E E-09 Ps90%/90% (+KTL) Un-Biased 3.97E E E E E E E E-08 Ps90%/90% (-KTL) Un-Biased -2.19E E E E E E E E-08 Specification MIN -4.00E E E E E E E E-07 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-07 Status PASS PASS PASS N/A N/A PASS PASS PASS 27

28 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Positive Input Bias #1 (A) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Positive Input Bias #1 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 28

29 Table Raw data for Positive Input Bias #1 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Input Bias #1 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-07 Biased Statistics Average Biased 1.62E E E E E E E E-07 Std Dev Biased 8.37E E E E E E E E-08 Ps90%/90% (+KTL) Biased 1.85E E E E E E E E-07 Ps90%/90% (-KTL) Biased 1.39E E E E E E E E-07 Un-Biased Statistics Average Un-Biased 1.46E E E E E E E E-07 Std Dev Un-Biased 1.82E E E E E E E E-08 Ps90%/90% (+KTL) Un-Biased 1.96E E E E E E E E-07 Ps90%/90% (-KTL) Un-Biased 9.62E E E E E E E E-07 Specification MIN -4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS 29

30 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Positive Input Bias #2 (A) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Positive Input Bias #2 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 30

31 Table Raw data for Positive Input Bias #2 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Input Bias #2 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-07 Biased Statistics Average Biased 1.56E E E E E E E E-07 Std Dev Biased 1.52E E E E E E E E-08 Ps90%/90% (+KTL) Biased 1.98E E E E E E E E-07 Ps90%/90% (-KTL) Biased 1.14E E E E E E E E-07 Un-Biased Statistics Average Un-Biased 1.48E E E E E E E E-07 Std Dev Un-Biased 1.10E E E E E E E E-09 Ps90%/90% (+KTL) Un-Biased 1.78E E E E E E E E-07 Ps90%/90% (-KTL) Un-Biased 1.18E E E E E E E E-07 Specification MIN -4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS 31

32 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Positive Input Bias #3 (A) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Positive Input Bias #3 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 32

33 Table Raw data for Positive Input Bias #3 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Input Bias #3 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-07 Biased Statistics Average Biased 1.60E E E E E E E E-07 Std Dev Biased 2.35E E E E E E E E-08 Ps90%/90% (+KTL) Biased 2.24E E E E E E E E-07 Ps90%/90% (-KTL) Biased 9.57E E E E E E E E-08 Un-Biased Statistics Average Un-Biased 1.52E E E E E E E E-07 Std Dev Un-Biased 1.30E E E E E E E E-08 Ps90%/90% (+KTL) Un-Biased 1.88E E E E E E E E-07 Ps90%/90% (-KTL) Un-Biased 1.16E E E E E E E E-07 Specification MIN -4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS 33

34 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Positive Input Bias #4 (A) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Positive Input Bias #4 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 34

35 Table Raw data for Positive Input Bias #4 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Input Bias #4 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-07 Biased Statistics Average Biased 1.64E E E E E E E E-07 Std Dev Biased 8.94E E E E E E E E-09 Ps90%/90% (+KTL) Biased 1.89E E E E E E E E-07 Ps90%/90% (-KTL) Biased 1.39E E E E E E E E-07 Un-Biased Statistics Average Un-Biased 1.50E E E E E E E E-07 Std Dev Un-Biased 1.41E E E E E E E E-09 Ps90%/90% (+KTL) Un-Biased 1.89E E E E E E E E-07 Ps90%/90% (-KTL) Un-Biased 1.11E E E E E E E E-07 Specification MIN -4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS 35

36 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Negative Input Bias #1 (A) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Negative Input Bias #1 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 36

37 Table Raw data for Negative Input Bias #1 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Input Bias #1 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-07 Biased Statistics Average Biased 1.60E E E E E E E E-07 Std Dev Biased 1.00E E E E E E E E-08 Ps90%/90% (+KTL) Biased 1.87E E E E E E E E-07 Ps90%/90% (-KTL) Biased 1.33E E E E E E E E-07 Un-Biased Statistics Average Un-Biased 1.46E E E E E E E E-07 Std Dev Un-Biased 1.14E E E E E E E E-08 Ps90%/90% (+KTL) Un-Biased 1.77E E E E E E E E-07 Ps90%/90% (-KTL) Un-Biased 1.15E E E E E E E E-07 Specification MIN -4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS 37

38 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Negative Input Bias #2 (A) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Negative Input Bias #2 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 38

39 Table Raw data for Negative Input Bias #2 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Input Bias #2 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-07 Biased Statistics Average Biased 1.54E E E E E E E E-07 Std Dev Biased 1.52E E E E E E E E-08 Ps90%/90% (+KTL) Biased 1.96E E E E E E E E-07 Ps90%/90% (-KTL) Biased 1.12E E E E E E E E-08 Un-Biased Statistics Average Un-Biased 1.48E E E E E E E E-07 Std Dev Un-Biased 1.48E E E E E E E E-08 Ps90%/90% (+KTL) Un-Biased 1.89E E E E E E E E-07 Ps90%/90% (-KTL) Un-Biased 1.07E E E E E E E E-07 Specification MIN -4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS 39

40 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Negative Input Bias #3 (A) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Negative Input Bias #3 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 40

41 Table Raw data for Negative Input Bias #3 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Input Bias #3 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-07 Biased Statistics Average Biased 1.58E E E E E E E E-07 Std Dev Biased 2.17E E E E E E E E-08 Ps90%/90% (+KTL) Biased 2.17E E E E E E E E-07 Ps90%/90% (-KTL) Biased 9.86E E E E E E E E-08 Un-Biased Statistics Average Un-Biased 1.54E E E E E E E E-07 Std Dev Un-Biased 1.14E E E E E E E E-08 Ps90%/90% (+KTL) Un-Biased 1.85E E E E E E E E-07 Ps90%/90% (-KTL) Un-Biased 1.23E E E E E E E E-07 Specification MIN -4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS 41

42 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Negative Input Bias #4 (A) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Negative Input Bias #4 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 42

43 Table Raw data for Negative Input Bias #4 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Input Bias #4 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-07 Biased Statistics Average Biased 1.62E E E E E E E E-07 Std Dev Biased 8.37E E E E E E E E-09 Ps90%/90% (+KTL) Biased 1.85E E E E E E E E-07 Ps90%/90% (-KTL) Biased 1.39E E E E E E E E-07 Un-Biased Statistics Average Un-Biased 1.42E E E E E E E E-07 Std Dev Un-Biased 1.48E E E E E E E E-08 Ps90%/90% (+KTL) Un-Biased 1.83E E E E E E E E-07 Ps90%/90% (-KTL) Un-Biased 1.01E E E E E E E E-07 Specification MIN -4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS 43

44 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Common Mode Rejection #1 (db) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Common Mode Rejection #1 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 44

45 Table Raw data for Common Mode Rejection #1 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Common Mode Rejection #1 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+01 Biased Statistics Average Biased 8.92E E E E E E E E+01 Std Dev Biased 7.06E E E E E E E E+00 Ps90%/90% (+KTL) Biased 9.12E E E E E E E E+01 Ps90%/90% (-KTL) Biased 8.73E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 8.94E E E E E E E E+01 Std Dev Un-Biased 9.90E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 9.21E E E E E E E E+01 Ps90%/90% (-KTL) Un-Biased 8.67E E E E E E E E+01 Specification MIN 7.50E E E E E E E E+01 Status PASS PASS PASS N/A N/A PASS PASS PASS 45

46 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Common Mode Rejection #2 (db) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Common Mode Rejection #2 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 46

47 Table Raw data for Common Mode Rejection #2 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Common Mode Rejection #2 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+01 Biased Statistics Average Biased 8.90E E E E E E E E+01 Std Dev Biased 1.84E E E E E E E E+00 Ps90%/90% (+KTL) Biased 9.41E E E E E E E E+01 Ps90%/90% (-KTL) Biased 8.39E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 9.02E E E E E E E E+01 Std Dev Un-Biased 1.11E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 9.33E E E E E E E E+01 Ps90%/90% (-KTL) Un-Biased 8.72E E E E E E E E+01 Specification MIN 7.50E E E E E E E E+01 Status PASS PASS PASS N/A N/A PASS PASS PASS 47

48 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Common Mode Rejection #3 (db) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Common Mode Rejection #3 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 48

49 Table Raw data for Common Mode Rejection #3 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Common Mode Rejection #3 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+01 Biased Statistics Average Biased 9.00E E E E E E E E+01 Std Dev Biased 1.77E E E E E E E E+00 Ps90%/90% (+KTL) Biased 9.49E E E E E E E E+01 Ps90%/90% (-KTL) Biased 8.52E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 8.97E E E E E E E E+01 Std Dev Un-Biased 1.41E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 9.35E E E E E E E E+01 Ps90%/90% (-KTL) Un-Biased 8.58E E E E E E E E+01 Specification MIN 7.50E E E E E E E E+01 Status PASS PASS PASS N/A N/A PASS PASS PASS 49

50 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Common Mode Rejection #4 (db) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Common Mode Rejection #4 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 50

51 Table Raw data for Common Mode Rejection #4 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Common Mode Rejection #4 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+01 Biased Statistics Average Biased 8.96E E E E E E E E+01 Std Dev Biased 1.89E E E E E E E E+00 Ps90%/90% (+KTL) Biased 9.48E E E E E E E E+01 Ps90%/90% (-KTL) Biased 8.44E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 9.07E E E E E E E E+01 Std Dev Un-Biased 1.22E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 9.40E E E E E E E E+01 Ps90%/90% (-KTL) Un-Biased 8.73E E E E E E E E+01 Specification MIN 7.50E E E E E E E E+01 Status PASS PASS PASS N/A N/A PASS PASS PASS 51

52 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 1.20E+02 Power Supply Rejection Ratio #1 (db) 1.00E E E E E E hr hr 70 Figure Plot of Power Supply Rejection Ratio #1 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 52

53 Table Raw data for Power Supply Rejection Ratio #1 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Power Supply Rejection Ratio #1 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.01E E E E E E E E+01 Std Dev Biased 5.86E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.17E E E E E E E E+02 Ps90%/90% (-KTL) Biased 8.46E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.01E E E E E E E E+02 Std Dev Un-Biased 5.38E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.16E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 8.67E E E E E E E E+01 Specification MIN 7.80E E E E E E E E+01 Status PASS PASS PASS N/A N/A PASS PASS PASS 53

54 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 1.20E+02 Power Supply Rejection Ratio #2 (db) 1.00E E E E E E hr hr 70 Figure Plot of Power Supply Rejection Ratio #2 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 54

55 Table Raw data for Power Supply Rejection Ratio #2 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Power Supply Rejection Ratio #2 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 9.97E E E E E E E E+01 Std Dev Biased 3.40E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.09E E E E E E E E+02 Ps90%/90% (-KTL) Biased 9.04E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.01E E E E E E E E+02 Std Dev Un-Biased 8.02E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.23E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 7.92E E E E E E E E+01 Specification MIN 7.80E E E E E E E E+01 Status PASS PASS PASS N/A N/A PASS PASS PASS 55

56 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 1.20E+02 Power Supply Rejection Ratio #3 (db) 1.00E E E E E E hr hr 70 Figure Plot of Power Supply Rejection Ratio #3 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 56

57 Table Raw data for Power Supply Rejection Ratio #3 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Power Supply Rejection Ratio #3 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.06E E E E E E E E+02 Std Dev Biased 1.22E E E E E E E E+01 Ps90%/90% (+KTL) Biased 1.39E E E E E E E E+02 Ps90%/90% (-KTL) Biased 7.20E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 9.87E E E E E E E E+01 Std Dev Un-Biased 6.68E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.17E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 8.04E E E E E E E E+01 Specification MIN 7.80E E E E E E E E+01 Status PASS PASS PASS N/A N/A PASS PASS PASS 57

58 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 1.20E+02 Power Supply Rejection Ratio #4 (db) 1.00E E E E E E hr hr 70 Figure Plot of Power Supply Rejection Ratio #4 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 58

59 Table Raw data for Power Supply Rejection Ratio #4 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Power Supply Rejection Ratio #4 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+01 Biased Statistics Average Biased 1.06E E E E E E E E+02 Std Dev Biased 6.13E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.23E E E E E E E E+02 Ps90%/90% (-KTL) Biased 8.91E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.09E E E E E E E E+02 Std Dev Un-Biased 7.13E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.28E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 8.94E E E E E E E E+01 Specification MIN 7.80E E E E E E E E+01 Status PASS PASS PASS N/A N/A PASS PASS PASS 59

60 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Large Signal Voltage RL=500 #1 (V/mV) 5.00E E E E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased Specification MIN hr hr 70 Figure Plot of Large Signal Voltage RL=500 #1 (V/mV) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 60

61 Table Raw data for Large Signal Voltage RL=500 #1 (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Large Signal Voltage RL=500 #1 (V/mV) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 4.40E E E E E E E E+00 Std Dev Biased 7.96E E E E E E E E-02 Ps90%/90% (+KTL) Biased 4.62E E E E E E E E+00 Ps90%/90% (-KTL) Biased 4.18E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 4.57E E E E E E E E+00 Std Dev Un-Biased 2.64E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 5.29E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 3.85E E E E E E E E+00 Specification MIN 1.50E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 61

62 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Large Signal Voltage RL=500 #2 (V/mV) 5.00E E E E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased Specification MIN hr hr 70 Figure Plot of Large Signal Voltage RL=500 #2 (V/mV) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 62

63 Table Raw data for Large Signal Voltage RL=500 #2 (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Large Signal Voltage RL=500 #2 (V/mV) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 4.40E E E E E E E E+00 Std Dev Biased 7.86E E E E E E E E-01 Ps90%/90% (+KTL) Biased 4.61E E E E E E E E+00 Ps90%/90% (-KTL) Biased 4.18E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 4.48E E E E E E E E+00 Std Dev Un-Biased 1.91E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 5.01E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 3.96E E E E E E E E+00 Specification MIN 1.50E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 63

64 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Large Signal Voltage RL=500 #3 (V/mV) 5.00E E E E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased Specification MIN hr hr 70 Figure Plot of Large Signal Voltage RL=500 #3 (V/mV) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 64

65 Table Raw data for Large Signal Voltage RL=500 #3 (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Large Signal Voltage RL=500 #3 (V/mV) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 4.44E E E E E E E E+00 Std Dev Biased 1.13E E E E E E E E-01 Ps90%/90% (+KTL) Biased 4.75E E E E E E E E+00 Ps90%/90% (-KTL) Biased 4.13E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 4.54E E E E E E E E+00 Std Dev Un-Biased 2.17E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 5.14E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 3.95E E E E E E E E+00 Specification MIN 1.50E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 65

66 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Large Signal Voltage RL=500 #4 (V/mV) 5.00E E E E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased Specification MIN hr hr 70 Figure Plot of Large Signal Voltage RL=500 #4 (V/mV) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 66

67 Table Raw data for Large Signal Voltage RL=500 #4 (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Large Signal Voltage RL=500 #4 (V/mV) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 4.37E E E E E E E E+00 Std Dev Biased 1.01E E E E E E E E-01 Ps90%/90% (+KTL) Biased 4.65E E E E E E E E+00 Ps90%/90% (-KTL) Biased 4.09E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 4.52E E E E E E E E+00 Std Dev Un-Biased 2.41E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 5.18E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 3.86E E E E E E E E+00 Specification MIN 1.50E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 67

68 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Large Signal Voltage RL=100 #1 (V/mV) 4.00E E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased Specification MIN hr hr 70 Figure Plot of Large Signal Voltage RL=100 #1 (V/mV) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 68

69 Table Raw data for Large Signal Voltage RL=100 #1 (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Large Signal Voltage RL=100 #1 (V/mV) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 3.50E E E E E E E E+00 Std Dev Biased 7.94E E E E E E E E-02 Ps90%/90% (+KTL) Biased 3.72E E E E E E E E+00 Ps90%/90% (-KTL) Biased 3.28E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 3.65E E E E E E E E+00 Std Dev Un-Biased 2.15E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 4.24E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 3.06E E E E E E E E+00 Specification MIN 1.00E E E E E E E E-01 Status PASS PASS PASS N/A N/A PASS PASS PASS 69

70 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Large Signal Voltage RL=100 #2 (V/mV) 4.00E E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased Specification MIN hr hr 70 Figure Plot of Large Signal Voltage RL=100 #2 (V/mV) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 70

71 Table Raw data for Large Signal Voltage RL=100 #2 (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Large Signal Voltage RL=100 #2 (V/mV) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 3.49E E E E E E E E+00 Std Dev Biased 7.36E E E E E E E E-01 Ps90%/90% (+KTL) Biased 3.69E E E E E E E E+00 Ps90%/90% (-KTL) Biased 3.29E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 3.57E E E E E E E E+00 Std Dev Un-Biased 1.27E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 3.92E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 3.22E E E E E E E E+00 Specification MIN 1.00E E E E E E E E-01 Status PASS PASS PASS N/A N/A PASS PASS PASS 71

72 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Large Signal Voltage RL=100 #3 (V/mV) 4.00E E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased Specification MIN hr hr 70 Figure Plot of Large Signal Voltage RL=100 #3 (V/mV) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 72

73 Table Raw data for Large Signal Voltage RL=100 #3 (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Large Signal Voltage RL=100 #3 (V/mV) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 3.54E E E E E E E E+00 Std Dev Biased 1.16E E E E E E E E-01 Ps90%/90% (+KTL) Biased 3.86E E E E E E E E+00 Ps90%/90% (-KTL) Biased 3.22E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 3.64E E E E E E E E+00 Std Dev Un-Biased 1.66E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 4.10E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 3.19E E E E E E E E+00 Specification MIN 1.00E E E E E E E E-01 Status PASS PASS PASS N/A N/A PASS PASS PASS 73

74 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Large Signal Voltage RL=100 #4 (V/mV) 4.00E E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased Specification MIN hr hr 70 Figure Plot of Large Signal Voltage RL=100 #4 (V/mV) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 74

75 Table Raw data for Large Signal Voltage RL=100 #4 (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Large Signal Voltage RL=100 #4 (V/mV) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 3.48E E E E E E E E+00 Std Dev Biased 9.60E E E E E E E E-02 Ps90%/90% (+KTL) Biased 3.74E E E E E E E E+00 Ps90%/90% (-KTL) Biased 3.22E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 3.58E E E E E E E E+00 Std Dev Un-Biased 1.63E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 4.03E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 3.14E E E E E E E E+00 Specification MIN 1.00E E E E E E E E-01 Status PASS PASS PASS N/A N/A PASS PASS PASS 75

76 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 1.40E+02 Channel 1:2 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 1:2 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 76

77 Table Raw data for Channel 1:2 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 1:2 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.10E E E E E E E E+02 Std Dev Biased 6.31E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.28E E E E E E E E+02 Ps90%/90% (-KTL) Biased 9.31E E E E E E E E+02 Un-Biased Statistics Average Un-Biased 1.22E E E E E E E E+02 Std Dev Un-Biased 8.62E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.45E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 9.81E E E E E E E E+01 Specification MIN 8.20E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 77

78 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 1.40E+02 Channel 1:3 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 1:3 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 78

79 Table Raw data for Channel 1:3 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 1:3 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.20E E E E E E E E+02 Std Dev Biased 6.65E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.38E E E E E E E E+02 Ps90%/90% (-KTL) Biased 1.01E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.22E E E E E E E E+02 Std Dev Un-Biased 1.60E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.65E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 7.77E E E E E E E E+02 Specification MIN 8.20E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 79

80 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 1.40E+02 Channel 1:4 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 1:4 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 80

81 Table Raw data for Channel 1:4 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 1:4 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.15E E E E E E E E+02 Std Dev Biased 1.56E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.58E E E E E E E E+02 Ps90%/90% (-KTL) Biased 7.26E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.09E E E E E E E E+02 Std Dev Un-Biased 3.74E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.19E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 9.86E E E E E E E E+01 Specification MIN 8.20E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 81

82 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 1.40E+02 Channel 2:1 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 2:1 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 82

83 Table Raw data for Channel 2:1 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 2:1 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.23E E E E E E E E+02 Std Dev Biased 9.66E E E E E E E E+01 Ps90%/90% (+KTL) Biased 1.49E E E E E E E E+02 Ps90%/90% (-KTL) Biased 9.63E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.21E E E E E E E E+02 Std Dev Un-Biased 1.09E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.50E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 9.08E E E E E E E E+01 Specification MIN 8.20E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 83

84 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 1.40E+02 Channel 2:3 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 2:3 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 84

85 Table Raw data for Channel 2:3 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 2:3 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.06E E E E E E E E+02 Std Dev Biased 3.38E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.15E E E E E E E E+02 Ps90%/90% (-KTL) Biased 9.66E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.04E E E E E E E E+02 Std Dev Un-Biased 3.50E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.14E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 9.49E E E E E E E E+01 Specification MIN 8.20E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 85

86 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 1.40E+02 Channel 2:4 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 2:4 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 86

87 Table Raw data for Channel 2:4 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 2:4 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.24E E E E E E E E+02 Std Dev Biased 1.42E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.63E E E E E E E E+02 Ps90%/90% (-KTL) Biased 8.51E E E E E E E E+02 Un-Biased Statistics Average Un-Biased 1.20E E E E E E E E+02 Std Dev Un-Biased 4.89E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.33E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 1.06E E E E E E E E+01 Specification MIN 8.20E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 87

88 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 1.40E+02 Channel 3:1 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 3:1 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 88

89 Table Raw data for Channel 3:1 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 3:1 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.12E E E E E E E E+02 Std Dev Biased 8.46E E E E E E E E+01 Ps90%/90% (+KTL) Biased 1.35E E E E E E E E+02 Ps90%/90% (-KTL) Biased 8.90E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.23E E E E E E E E+02 Std Dev Un-Biased 1.11E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.54E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 9.30E E E E E E E E+01 Specification MIN 8.20E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 89

90 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 1.40E+02 Channel 3:2 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 3:2 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 90

91 Table Raw data for Channel 3:2 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 3:2 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.07E E E E E E E E+02 Std Dev Biased 4.57E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.19E E E E E E E E+02 Ps90%/90% (-KTL) Biased 9.44E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.15E E E E E E E E+02 Std Dev Un-Biased 6.29E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.32E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 9.76E E E E E E E E+02 Specification MIN 8.20E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 91

92 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 1.40E+02 Channel 3:4 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 3:4 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 92

93 Table Raw data for Channel 3:4 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 3:4 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.19E E E E E E E E+02 Std Dev Biased 6.67E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.38E E E E E E E E+02 Ps90%/90% (-KTL) Biased 1.01E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.20E E E E E E E E+02 Std Dev Un-Biased 1.03E E E E E E E E+01 Ps90%/90% (+KTL) Un-Biased 1.48E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 9.18E E E E E E E E+01 Specification MIN 8.20E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 93

94 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 1.20E+02 Channel 4:1 (db) 1.00E E E E E E hr hr 70 Figure Plot of Channel 4:1 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 94

95 Table Raw data for Channel 4:1 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 4:1 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.08E E E E E E E E+02 Std Dev Biased 4.88E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.21E E E E E E E E+02 Ps90%/90% (-KTL) Biased 9.42E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.03E E E E E E E E+02 Std Dev Un-Biased 1.63E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.08E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 9.90E E E E E E E E+01 Specification MIN 8.20E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 95

96 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 1.40E+02 Channel 4:2 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 4:2 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 96

97 Table Raw data for Channel 4:2 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 4:2 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.17E E E E E E E E+02 Std Dev Biased 3.56E E E E E E E E+01 Ps90%/90% (+KTL) Biased 1.27E E E E E E E E+02 Ps90%/90% (-KTL) Biased 1.08E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.18E E E E E E E E+02 Std Dev Un-Biased 5.21E E E E E E E E+01 Ps90%/90% (+KTL) Un-Biased 1.32E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 1.04E E E E E E E E+01 Specification MIN 8.20E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 97

98 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 1.40E+02 Channel 4:3 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 4:3 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 98

99 Table Raw data for Channel 4:3 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 4:3 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.14E E E E E E E E+02 Std Dev Biased 2.81E E E E E E E E+01 Ps90%/90% (+KTL) Biased 1.21E E E E E E E E+02 Ps90%/90% (-KTL) Biased 1.06E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.19E E E E E E E E+02 Std Dev Un-Biased 1.05E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.48E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 9.05E E E E E E E E+01 Specification MIN 8.20E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 99

100 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Output Voltage Swing RL=500 #1 (V) 4.05E E E E E E E E E hr hr 70 Figure Plot of Output Voltage Swing RL=500 #1 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 100

101 Table Raw data for Output Voltage Swing RL=500 #1 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=500 #1 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 4.03E E E E E E E E+00 Std Dev Biased 1.14E E E E E E E E-03 Ps90%/90% (+KTL) Biased 4.03E E E E E E E E+00 Ps90%/90% (-KTL) Biased 4.02E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 4.03E E E E E E E E+00 Std Dev Un-Biased 2.05E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 4.03E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 4.02E E E E E E E E+00 Specification MIN 3.80E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 101

102 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Output Voltage Swing RL=500 #2 (V) 4.05E E E E E E E E E hr hr 70 Figure Plot of Output Voltage Swing RL=500 #2 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 102

103 Table Raw data for Output Voltage Swing RL=500 #2 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=500 #2 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 4.03E E E E E E E E+00 Std Dev Biased 1.14E E E E E E E E-03 Ps90%/90% (+KTL) Biased 4.03E E E E E E E E+00 Ps90%/90% (-KTL) Biased 4.02E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 4.03E E E E E E E E+00 Std Dev Un-Biased 1.52E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 4.03E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 4.02E E E E E E E E+00 Specification MIN 3.80E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 103

104 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Output Voltage Swing RL=500 #3 (V) 4.05E E E E E E E E E hr hr 70 Figure Plot of Output Voltage Swing RL=500 #3 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 104

105 Table Raw data for Output Voltage Swing RL=500 #3 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=500 #3 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 4.03E E E E E E E E+00 Std Dev Biased 1.14E E E E E E E E-03 Ps90%/90% (+KTL) Biased 4.03E E E E E E E E+00 Ps90%/90% (-KTL) Biased 4.02E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 4.03E E E E E E E E+00 Std Dev Un-Biased 1.10E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 4.03E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 4.02E E E E E E E E+00 Specification MIN 3.80E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 105

106 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Output Voltage Swing RL=500 #4 (V) 4.05E E E E E E E E E hr hr 70 Figure Plot of Output Voltage Swing RL=500 #4 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 106

107 Table Raw data for Output Voltage Swing RL=500 #4 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=500 #4 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 4.03E E E E E E E E+00 Std Dev Biased 1.30E E E E E E E E-03 Ps90%/90% (+KTL) Biased 4.03E E E E E E E E+00 Ps90%/90% (-KTL) Biased 4.02E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 4.03E E E E E E E E+00 Std Dev Un-Biased 1.82E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 4.03E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 4.02E E E E E E E E+00 Specification MIN 3.80E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 107

108 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Output Voltage Swing RL=100 #1 (V) 3.70E E E E E E E E E E E hr hr 70 Figure Plot of Output Voltage Swing RL=100 #1 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 108

109 Table Raw data for Output Voltage Swing RL=100 #1 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=100 #1 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 3.64E E E E E E E E+00 Std Dev Biased 2.68E E E E E E E E-03 Ps90%/90% (+KTL) Biased 3.65E E E E E E E E+00 Ps90%/90% (-KTL) Biased 3.63E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 3.64E E E E E E E E+00 Std Dev Un-Biased 4.72E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 3.65E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 3.63E E E E E E E E+00 Specification MIN 3.35E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 109

110 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Output Voltage Swing RL=100 #2 (V) 3.70E E E E E E E E E E E hr hr 70 Figure Plot of Output Voltage Swing RL=100 #2 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 110

111 Table Raw data for Output Voltage Swing RL=100 #2 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=100 #2 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 3.64E E E E E E E E+00 Std Dev Biased 4.22E E E E E E E E-03 Ps90%/90% (+KTL) Biased 3.65E E E E E E E E+00 Ps90%/90% (-KTL) Biased 3.63E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 3.64E E E E E E E E+00 Std Dev Un-Biased 3.49E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 3.65E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 3.63E E E E E E E E+00 Specification MIN 3.35E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 111

112 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Output Voltage Swing RL=100 #3 (V) 3.70E E E E E E E E E E E hr hr 70 Figure Plot of Output Voltage Swing RL=100 #3 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 112

113 Table Raw data for Output Voltage Swing RL=100 #3 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=100 #3 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 3.64E E E E E E E E+00 Std Dev Biased 4.76E E E E E E E E-03 Ps90%/90% (+KTL) Biased 3.65E E E E E E E E+00 Ps90%/90% (-KTL) Biased 3.63E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 3.64E E E E E E E E+00 Std Dev Un-Biased 3.11E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 3.65E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 3.63E E E E E E E E+00 Specification MIN 3.35E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 113

114 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Output Voltage Swing RL=100 #4 (V) 3.70E E E E E E E E E E E hr hr 70 Figure Plot of Output Voltage Swing RL=100 #4 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 114

115 Table Raw data for Output Voltage Swing RL=100 #4 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=100 #4 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 3.64E E E E E E E E+00 Std Dev Biased 3.36E E E E E E E E-03 Ps90%/90% (+KTL) Biased 3.65E E E E E E E E+00 Ps90%/90% (-KTL) Biased 3.63E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 3.64E E E E E E E E+00 Std Dev Un-Biased 4.66E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 3.65E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 3.63E E E E E E E E+00 Specification MIN 3.35E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 115

116 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Output Voltage Swing RL=500 #1 (V) -3.65E E E E E E E E E hr hr 70 Figure Plot of Output Voltage Swing RL=500 #1 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 116

117 Table Raw data for Output Voltage Swing RL=500 #1 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=500 #1 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased -4.03E E E E E E E E+00 Std Dev Biased 1.30E E E E E E E E-02 Ps90%/90% (+KTL) Biased -4.02E E E E E E E E+00 Ps90%/90% (-KTL) Biased -4.03E E E E E E E E+00 Un-Biased Statistics Average Un-Biased -4.03E E E E E E E E+00 Std Dev Un-Biased 2.35E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased -4.02E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased -4.04E E E E E E E E+00 Specification MAX -3.80E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 117

118 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Output Voltage Swing RL=500 #2 (V) -3.65E E E E E E E E E hr hr 70 Figure Plot of Output Voltage Swing RL=500 #2 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 118

119 Table Raw data for Output Voltage Swing RL=500 #2 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=500 #2 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased -4.03E E E E E E E E+00 Std Dev Biased 1.64E E E E E E E E-02 Ps90%/90% (+KTL) Biased -4.02E E E E E E E E+00 Ps90%/90% (-KTL) Biased -4.03E E E E E E E E+00 Un-Biased Statistics Average Un-Biased -4.03E E E E E E E E+00 Std Dev Un-Biased 2.55E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased -4.02E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased -4.03E E E E E E E E+00 Specification MAX -3.80E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 119

120 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Output Voltage Swing RL=500 #3 (V) -3.65E E E E E E E E E hr hr 70 Figure Plot of Output Voltage Swing RL=500 #3 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 120

121 Table Raw data for Output Voltage Swing RL=500 #3 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=500 #3 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased -4.03E E E E E E E E+00 Std Dev Biased 1.52E E E E E E E E-02 Ps90%/90% (+KTL) Biased -4.02E E E E E E E E+00 Ps90%/90% (-KTL) Biased -4.03E E E E E E E E+00 Un-Biased Statistics Average Un-Biased -4.03E E E E E E E E+00 Std Dev Un-Biased 2.70E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased -4.02E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased -4.04E E E E E E E E+00 Specification MAX -3.80E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 121

122 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Output Voltage Swing RL=500 #4 (V) -3.65E E E E E E E E E hr hr 70 Figure Plot of Output Voltage Swing RL=500 #4 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 122

123 Table Raw data for Output Voltage Swing RL=500 #4 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=500 #4 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased -4.03E E E E E E E E+00 Std Dev Biased 1.10E E E E E E E E-02 Ps90%/90% (+KTL) Biased -4.02E E E E E E E E+00 Ps90%/90% (-KTL) Biased -4.03E E E E E E E E+00 Un-Biased Statistics Average Un-Biased -4.03E E E E E E E E+00 Std Dev Un-Biased 2.07E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased -4.02E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased -4.04E E E E E E E E+00 Specification MAX -3.80E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 123

124 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Output Voltage Swing RL=100 #1 (V) -3.20E E E E E E E E E E hr hr 70 Figure Plot of Output Voltage Swing RL=100 #1 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 124

125 Table Raw data for Output Voltage Swing RL=100 #1 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=100 #1 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased -3.59E E E E E E E E+00 Std Dev Biased 1.30E E E E E E E E-02 Ps90%/90% (+KTL) Biased -3.58E E E E E E E E+00 Ps90%/90% (-KTL) Biased -3.59E E E E E E E E+00 Un-Biased Statistics Average Un-Biased -3.59E E E E E E E E+00 Std Dev Un-Biased 5.50E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased -3.58E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased -3.61E E E E E E E E+00 Specification MAX -3.35E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 125

126 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Output Voltage Swing RL=100 #2 (V) -3.20E E E E E E E E E E hr hr 70 Figure Plot of Output Voltage Swing RL=100 #2 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 126

127 Table Raw data for Output Voltage Swing RL=100 #2 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=100 #2 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased -3.59E E E E E E E E+00 Std Dev Biased 2.00E E E E E E E E-02 Ps90%/90% (+KTL) Biased -3.58E E E E E E E E+00 Ps90%/90% (-KTL) Biased -3.59E E E E E E E E+00 Un-Biased Statistics Average Un-Biased -3.59E E E E E E E E+00 Std Dev Un-Biased 2.95E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased -3.58E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased -3.60E E E E E E E E+00 Specification MAX -3.35E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 127

128 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Output Voltage Swing RL=100 #3 (V) -3.20E E E E E E E E E E hr hr 70 Figure Plot of Output Voltage Swing RL=100 #3 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 128

129 Table Raw data for Output Voltage Swing RL=100 #3 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=100 #3 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased -3.59E E E E E E E E+00 Std Dev Biased 1.95E E E E E E E E-02 Ps90%/90% (+KTL) Biased -3.58E E E E E E E E+00 Ps90%/90% (-KTL) Biased -3.59E E E E E E E E+00 Un-Biased Statistics Average Un-Biased -3.59E E E E E E E E+00 Std Dev Un-Biased 2.49E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased -3.58E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased -3.60E E E E E E E E+00 Specification MAX -3.35E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 129

130 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Output Voltage Swing RL=100 #4 (V) -3.20E E E E E E E E E E hr hr 70 Figure Plot of Output Voltage Swing RL=100 #4 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 130

131 Table Raw data for Output Voltage Swing RL=100 #4 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=100 #4 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased -3.59E E E E E E E E+00 Std Dev Biased 1.14E E E E E E E E-02 Ps90%/90% (+KTL) Biased -3.59E E E E E E E E+00 Ps90%/90% (-KTL) Biased -3.59E E E E E E E E+00 Un-Biased Statistics Average Un-Biased -3.59E E E E E E E E+00 Std Dev Un-Biased 4.95E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased -3.58E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased -3.60E E E E E E E E+00 Specification MAX -3.35E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 131

132 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Maximum Output Source #1 (A) 7.00E E E E E E E E hr hr 70 Figure Plot of Maximum Output Source #1 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 132

133 Table Raw data for Maximum Output Source #1 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Maximum Output Source #1 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased 6.34E E E E E E E E-02 Std Dev Biased 4.14E E E E E E E E-04 Ps90%/90% (+KTL) Biased 6.45E E E E E E E E-02 Ps90%/90% (-KTL) Biased 6.22E E E E E E E E-02 Un-Biased Statistics Average Un-Biased 6.36E E E E E E E E-02 Std Dev Un-Biased 9.19E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 6.61E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased 6.11E E E E E E E E-02 Specification MIN 4.00E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 133

134 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Maximum Output Source #2 (A) 7.00E E E E E E E E hr hr 70 Figure Plot of Maximum Output Source #2 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 134

135 Table Raw data for Maximum Output Source #2 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Maximum Output Source #2 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased 6.34E E E E E E E E-02 Std Dev Biased 7.35E E E E E E E E-04 Ps90%/90% (+KTL) Biased 6.55E E E E E E E E-02 Ps90%/90% (-KTL) Biased 6.14E E E E E E E E-02 Un-Biased Statistics Average Un-Biased 6.31E E E E E E E E-02 Std Dev Un-Biased 4.90E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 6.44E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased 6.17E E E E E E E E-02 Specification MIN 4.00E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 135

136 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Maximum Output Source #3 (A) 7.00E E E E E E E E hr hr 70 Figure Plot of Maximum Output Source #3 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 136

137 Table Raw data for Maximum Output Source #3 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Maximum Output Source #3 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased 6.34E E E E E E E E-02 Std Dev Biased 7.82E E E E E E E E-04 Ps90%/90% (+KTL) Biased 6.56E E E E E E E E-02 Ps90%/90% (-KTL) Biased 6.13E E E E E E E E-02 Un-Biased Statistics Average Un-Biased 6.30E E E E E E E E-02 Std Dev Un-Biased 4.80E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 6.44E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased 6.17E E E E E E E E-02 Specification MIN 4.00E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 137

138 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Maximum Output Source #4 (A) 7.00E E E E E E E E hr hr 70 Figure Plot of Maximum Output Source #4 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 138

139 Table Raw data for Maximum Output Source #4 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Maximum Output Source #4 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased 6.33E E E E E E E E-02 Std Dev Biased 4.94E E E E E E E E-04 Ps90%/90% (+KTL) Biased 6.47E E E E E E E E-02 Ps90%/90% (-KTL) Biased 6.20E E E E E E E E-02 Un-Biased Statistics Average Un-Biased 6.34E E E E E E E E-02 Std Dev Un-Biased 8.42E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 6.58E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased 6.11E E E E E E E E-02 Specification MIN 4.00E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 139

140 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Maximum Output Sink #1 (A) 0.00E E E E E E E hr hr 70 Figure Plot of Maximum Output Sink #1 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 140

141 Table Raw data for Maximum Output Sink #1 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Maximum Output Sink #1 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased -5.67E E E E E E E E-02 Std Dev Biased 3.28E E E E E E E E-03 Ps90%/90% (+KTL) Biased -5.58E E E E E E E E-02 Ps90%/90% (-KTL) Biased -5.76E E E E E E E E-02 Un-Biased Statistics Average Un-Biased -5.70E E E E E E E E-02 Std Dev Un-Biased 1.33E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased -5.33E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased -6.06E E E E E E E E-02 Specification MAX -4.00E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 141

142 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Maximum Output Sink #2 (A) 0.00E E E E E E E hr hr 70 Figure Plot of Maximum Output Sink #2 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 142

143 Table Raw data for Maximum Output Sink #2 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Maximum Output Sink #2 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased -5.68E E E E E E E E-02 Std Dev Biased 5.47E E E E E E E E-03 Ps90%/90% (+KTL) Biased -5.53E E E E E E E E-02 Ps90%/90% (-KTL) Biased -5.83E E E E E E E E-02 Un-Biased Statistics Average Un-Biased -5.66E E E E E E E E-02 Std Dev Un-Biased 7.50E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased -5.45E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased -5.86E E E E E E E E-02 Specification MAX -4.00E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 143

144 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Maximum Output Sink #3 (A) 0.00E E E E E E E hr hr 70 Figure Plot of Maximum Output Sink #3 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 144

145 Table Raw data for Maximum Output Sink #3 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Maximum Output Sink #3 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased -5.69E E E E E E E E-02 Std Dev Biased 6.15E E E E E E E E-03 Ps90%/90% (+KTL) Biased -5.52E E E E E E E E-02 Ps90%/90% (-KTL) Biased -5.86E E E E E E E E-02 Un-Biased Statistics Average Un-Biased -5.66E E E E E E E E-02 Std Dev Un-Biased 5.16E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased -5.52E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased -5.80E E E E E E E E-02 Specification MAX -4.00E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 145

146 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Maximum Output Sink #4 (A) 0.00E E E E E E E hr hr 70 Figure Plot of Maximum Output Sink #4 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 146

147 Table Raw data for Maximum Output Sink #4 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Maximum Output Sink #4 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased -5.68E E E E E E E E-02 Std Dev Biased 3.42E E E E E E E E-03 Ps90%/90% (+KTL) Biased -5.58E E E E E E E E-02 Ps90%/90% (-KTL) Biased -5.77E E E E E E E E-02 Un-Biased Statistics Average Un-Biased -5.68E E E E E E E E-02 Std Dev Un-Biased 1.17E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased -5.36E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased -6.01E E E E E E E E-02 Specification MAX -4.00E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 147

148 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Positive Short-Circuit #1 (A) 9.00E E E E E E E E E hr hr 70 Figure Plot of Positive Short-Circuit #1 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 148

149 Table Raw data for Positive Short-Circuit #1 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Short-Circuit #1 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased 8.59E E E E E E E E-02 Std Dev Biased 3.40E E E E E E E E-04 Ps90%/90% (+KTL) Biased 8.69E E E E E E E E-02 Ps90%/90% (-KTL) Biased 8.50E E E E E E E E-02 Un-Biased Statistics Average Un-Biased 8.62E E E E E E E E-02 Std Dev Un-Biased 5.81E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 8.78E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased 8.46E E E E E E E E-02 Specification MIN 7.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 149

150 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Positive Short-Circuit #2 (A) 9.00E E E E E E E E E hr hr 70 Figure Plot of Positive Short-Circuit #2 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 150

151 Table Raw data for Positive Short-Circuit #2 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Short-Circuit #2 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased 8.60E E E E E E E E-02 Std Dev Biased 4.33E E E E E E E E-04 Ps90%/90% (+KTL) Biased 8.72E E E E E E E E-02 Ps90%/90% (-KTL) Biased 8.48E E E E E E E E-02 Un-Biased Statistics Average Un-Biased 8.60E E E E E E E E-02 Std Dev Un-Biased 5.57E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 8.75E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased 8.45E E E E E E E E-02 Specification MIN 7.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 151

152 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Positive Short-Circuit #3 (A) 8.80E E E E E E E E hr hr 70 Figure Plot of Positive Short-Circuit #3 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 152

153 Table Raw data for Positive Short-Circuit #3 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Short-Circuit #3 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased 8.59E E E E E E E E-02 Std Dev Biased 4.44E E E E E E E E-04 Ps90%/90% (+KTL) Biased 8.71E E E E E E E E-02 Ps90%/90% (-KTL) Biased 8.47E E E E E E E E-02 Un-Biased Statistics Average Un-Biased 8.59E E E E E E E E-02 Std Dev Un-Biased 6.25E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 8.76E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased 8.42E E E E E E E E-02 Specification MIN 7.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 153

154 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Positive Short-Circuit #4 (A) 8.80E E E E E E E E hr hr 70 Figure Plot of Positive Short-Circuit #4 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 154

155 Table Raw data for Positive Short-Circuit #4 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Short-Circuit #4 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased 8.59E E E E E E E E-02 Std Dev Biased 4.04E E E E E E E E-04 Ps90%/90% (+KTL) Biased 8.70E E E E E E E E-02 Ps90%/90% (-KTL) Biased 8.48E E E E E E E E-02 Un-Biased Statistics Average Un-Biased 8.61E E E E E E E E-02 Std Dev Un-Biased 5.72E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 8.77E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased 8.45E E E E E E E E-02 Specification MIN 7.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 155

156 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Negative Short-Circuit #1 (A) -7.40E E E E E E E E E E E hr hr 70 Figure Plot of Negative Short-Circuit #1 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 156

157 Table Raw data for Negative Short-Circuit #1 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Short-Circuit #1 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased -8.16E E E E E E E E-02 Std Dev Biased 3.56E E E E E E E E-04 Ps90%/90% (+KTL) Biased -8.06E E E E E E E E-02 Ps90%/90% (-KTL) Biased -8.25E E E E E E E E-02 Un-Biased Statistics Average Un-Biased -8.18E E E E E E E E-02 Std Dev Un-Biased 5.94E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased -8.02E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased -8.34E E E E E E E E-02 Specification MAX -7.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 157

158 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Negative Short-Circuit #2 (A) -7.40E E E E E E E E E E E hr hr 70 Figure Plot of Negative Short-Circuit #2 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 158

159 Table Raw data for Negative Short-Circuit #2 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Short-Circuit #2 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased -8.16E E E E E E E E-02 Std Dev Biased 4.83E E E E E E E E-04 Ps90%/90% (+KTL) Biased -8.03E E E E E E E E-02 Ps90%/90% (-KTL) Biased -8.30E E E E E E E E-02 Un-Biased Statistics Average Un-Biased -8.17E E E E E E E E-02 Std Dev Un-Biased 6.02E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased -8.01E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased -8.34E E E E E E E E-02 Specification MAX -7.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 159

160 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Negative Short-Circuit #3 (A) -7.40E E E E E E E E E E E hr hr 70 Figure Plot of Negative Short-Circuit #3 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 160

161 Table Raw data for Negative Short-Circuit #3 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Short-Circuit #3 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased -8.15E E E E E E E E-02 Std Dev Biased 4.11E E E E E E E E-04 Ps90%/90% (+KTL) Biased -8.04E E E E E E E E-02 Ps90%/90% (-KTL) Biased -8.27E E E E E E E E-02 Un-Biased Statistics Average Un-Biased -8.16E E E E E E E E-02 Std Dev Un-Biased 6.03E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased -7.99E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased -8.33E E E E E E E E-02 Specification MAX -7.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 161

162 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Negative Short-Circuit #4 (A) -7.40E E E E E E E E E E E hr hr 70 Figure Plot of Negative Short-Circuit #4 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 162

163 Table Raw data for Negative Short-Circuit #4 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Short-Circuit #4 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased -8.16E E E E E E E E-02 Std Dev Biased 3.60E E E E E E E E-04 Ps90%/90% (+KTL) Biased -8.06E E E E E E E E-02 Ps90%/90% (-KTL) Biased -8.26E E E E E E E E-02 Un-Biased Statistics Average Un-Biased -8.18E E E E E E E E-02 Std Dev Un-Biased 5.69E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased -8.02E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased -8.33E E E E E E E E-02 Specification MAX -7.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 163

164 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX 1.80E-02 Positive Supply (A) 1.60E E E E E E E E E hr hr 70 Figure Plot of Positive Supply (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 164

165 Table Raw data for Positive Supply (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Supply (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased 1.45E E E E E E E E-02 Std Dev Biased 2.51E E E E E E E E-04 Ps90%/90% (+KTL) Biased 1.52E E E E E E E E-02 Ps90%/90% (-KTL) Biased 1.38E E E E E E E E-02 Un-Biased Statistics Average Un-Biased 1.41E E E E E E E E-02 Std Dev Un-Biased 9.48E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 1.67E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased 1.15E E E E E E E E-02 Specification MAX 1.60E E E E E E E E-02 Status PASS PASS PASS N/A N/A PASS PASS PASS 165

166 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 0.00E+00 Negative Supply (A) -2.00E E E E E E E E E hr hr 70 Figure Plot of Negative Supply (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 166

167 Table Raw data for Negative Supply (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Supply (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased -1.45E E E E E E E E-02 Std Dev Biased 2.45E E E E E E E E-04 Ps90%/90% (+KTL) Biased -1.38E E E E E E E E-02 Ps90%/90% (-KTL) Biased -1.51E E E E E E E E-02 Un-Biased Statistics Average Un-Biased -1.40E E E E E E E E-02 Std Dev Un-Biased 9.41E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased -1.14E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased -1.66E E E E E E E E-02 Specification MIN -1.60E E E E E E E E-02 Status PASS PASS PASS N/A N/A PASS PASS PASS 167

168 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 5.00E-03 Input Offset #1 (V) 4.00E E E E E E E E E E hr hr 70 Figure Plot of Input Offset #1 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 168

169 Table Raw data for Input Offset #1 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset #1 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-05 Biased Statistics Average Biased -2.51E E E E E E E E-04 Std Dev Biased 3.84E E E E E E E E-04 Ps90%/90% (+KTL) Biased 8.01E E E E E E E E-04 Ps90%/90% (-KTL) Biased -1.30E E E E E E E E-03 Un-Biased Statistics Average Un-Biased -1.29E E E E E E E E-04 Std Dev Un-Biased 5.55E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 1.39E E E E E E E E-03 Ps90%/90% (-KTL) Un-Biased -1.65E E E E E E E E-03 Specification MIN -2.00E E E E E E E E-03 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 2.00E E E E E E E E-03 Status PASS PASS PASS N/A N/A PASS PASS PASS 169

170 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 5.00E-03 Input Offset #2 (V) 4.00E E E E E E E E E E hr hr 70 Figure Plot of Input Offset #2 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 170

171 Table Raw data for Input Offset #2 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset #2 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-04 Biased Statistics Average Biased -3.25E E E E E E E E-04 Std Dev Biased 4.04E E E E E E E E-04 Ps90%/90% (+KTL) Biased 7.82E E E E E E E E-04 Ps90%/90% (-KTL) Biased -1.43E E E E E E E E-03 Un-Biased Statistics Average Un-Biased -2.16E E E E E E E E-04 Std Dev Un-Biased 2.76E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 5.41E E E E E E E E-04 Ps90%/90% (-KTL) Un-Biased -9.73E E E E E E E E-03 Specification MIN -2.00E E E E E E E E-03 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 2.00E E E E E E E E-03 Status PASS PASS PASS N/A N/A PASS PASS PASS 171

172 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 5.00E-03 Input Offset #3 (V) 4.00E E E E E E E E E E hr hr 70 Figure Plot of Input Offset #3 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 172

173 Table Raw data for Input Offset #3 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset #3 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-04 Biased Statistics Average Biased -2.62E E E E E E E E-04 Std Dev Biased 6.09E E E E E E E E-04 Ps90%/90% (+KTL) Biased 1.41E E E E E E E E-03 Ps90%/90% (-KTL) Biased -1.93E E E E E E E E-03 Un-Biased Statistics Average Un-Biased -2.82E E E E E E E E-04 Std Dev Un-Biased 3.59E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 7.02E E E E E E E E-04 Ps90%/90% (-KTL) Un-Biased -1.27E E E E E E E E-03 Specification MIN -2.00E E E E E E E E-03 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 2.00E E E E E E E E-03 Status PASS PASS PASS N/A N/A PASS PASS PASS 173

174 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 5.00E-03 Input Offset #4 (V) 4.00E E E E E E E E E E hr hr 70 Figure Plot of Input Offset #4 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 174

175 Table Raw data for Input Offset #4 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset #4 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-05 Biased Statistics Average Biased -1.54E E E E E E E E-04 Std Dev Biased 2.09E E E E E E E E-04 Ps90%/90% (+KTL) Biased 4.20E E E E E E E E-04 Ps90%/90% (-KTL) Biased -7.28E E E E E E E E-04 Un-Biased Statistics Average Un-Biased 1.79E E E E E E E E-04 Std Dev Un-Biased 2.40E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 8.37E E E E E E E E-04 Ps90%/90% (-KTL) Un-Biased -4.79E E E E E E E E-04 Specification MIN -2.00E E E E E E E E-03 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 2.00E E E E E E E E-03 Status PASS PASS PASS N/A N/A PASS PASS PASS 175

176 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 1.00E-06 Input Offset #1 (A) 8.00E E E E E E E E E E hr hr 70 Figure Plot of Input Offset #1 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 176

177 Table Raw data for Input Offset #1 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset #1 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-08 Biased Statistics Average Biased 2.53E E E E E E E E-09 Std Dev Biased 6.99E E E E E E E E-09 Ps90%/90% (+KTL) Biased 2.17E E E E E E E E-08 Ps90%/90% (-KTL) Biased -1.66E E E E E E E E-08 Un-Biased Statistics Average Un-Biased 1.72E E E E E E E E-09 Std Dev Un-Biased 8.09E E E E E E E E-09 Ps90%/90% (+KTL) Un-Biased 2.39E E E E E E E E-08 Ps90%/90% (-KTL) Un-Biased -2.05E E E E E E E E-08 Specification MIN -4.00E E E E E E E E-07 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-07 Status PASS PASS PASS N/A N/A PASS PASS PASS 177

178 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 1.00E-06 Input Offset #2 (A) 8.00E E E E E E E E E E hr hr 70 Figure Plot of Input Offset #2 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 178

179 Table Raw data for Input Offset #2 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset #2 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 3.38E E E E E E E E-09 Std Dev Biased 1.34E E E E E E E E-08 Ps90%/90% (+KTL) Biased 4.00E E E E E E E E-08 Ps90%/90% (-KTL) Biased -3.33E E E E E E E E-08 Un-Biased Statistics Average Un-Biased 1.50E E E E E E E E+00 Std Dev Un-Biased 5.04E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.53E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased -1.23E E E E E E E E+00 Specification MIN -4.00E E E E E E E E-07 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-07 Status PASS PASS PASS N/A N/A PASS PASS PASS 179

180 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 1.00E-06 Input Offset #3 (A) 8.00E E E E E E E E E E hr hr 70 Figure Plot of Input Offset #3 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 180

181 Table Raw data for Input Offset #3 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset #3 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-08 Biased Statistics Average Biased 2.08E E E E E E E E+00 Std Dev Biased 3.16E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.07E E E E E E E E+00 Ps90%/90% (-KTL) Biased -6.58E E E E E E E E+00 Un-Biased Statistics Average Un-Biased -1.78E E E E E E E E+00 Std Dev Un-Biased 5.19E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.40E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased -1.44E E E E E E E E+00 Specification MIN -4.00E E E E E E E E-07 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-07 Status PASS PASS PASS N/A N/A PASS PASS PASS 181

182 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 1.00E-06 Input Offset #4 (A) 8.00E E E E E E E E E E hr hr 70 Figure Plot of Input Offset #4 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 182

183 Table Raw data for Input Offset #4 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset #4 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 5.26E E E E E E E E-09 Std Dev Biased 1.40E E E E E E E E-08 Ps90%/90% (+KTL) Biased 4.37E E E E E E E E-08 Ps90%/90% (-KTL) Biased -3.31E E E E E E E E-08 Un-Biased Statistics Average Un-Biased 1.14E E E E E E E E-08 Std Dev Un-Biased 1.39E E E E E E E E-08 Ps90%/90% (+KTL) Un-Biased 4.96E E E E E E E E-08 Ps90%/90% (-KTL) Un-Biased -2.68E E E E E E E E-08 Specification MIN -4.00E E E E E E E E-07 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-07 Status PASS PASS PASS N/A N/A PASS PASS PASS 183

184 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Positive Input Bias #1 (A) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Positive Input Bias #1 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 184

185 Table Raw data for Positive Input Bias #1 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Input Bias #1 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-07 Biased Statistics Average Biased 2.64E E E E E E E E-07 Std Dev Biased 1.14E E E E E E E E-08 Ps90%/90% (+KTL) Biased 2.95E E E E E E E E-07 Ps90%/90% (-KTL) Biased 2.33E E E E E E E E-07 Un-Biased Statistics Average Un-Biased 2.50E E E E E E E E-07 Std Dev Un-Biased 2.00E E E E E E E E-08 Ps90%/90% (+KTL) Un-Biased 3.05E E E E E E E E-07 Ps90%/90% (-KTL) Un-Biased 1.95E E E E E E E E-07 Specification MIN -4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS 185

186 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Positive Input Bias #2 (A) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Positive Input Bias #2 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 186

187 Table Raw data for Positive Input Bias #2 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Input Bias #2 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-07 Biased Statistics Average Biased 2.58E E E E E E E E-07 Std Dev Biased 1.79E E E E E E E E-08 Ps90%/90% (+KTL) Biased 3.07E E E E E E E E-07 Ps90%/90% (-KTL) Biased 2.09E E E E E E E E-07 Un-Biased Statistics Average Un-Biased 2.50E E E E E E E E-07 Std Dev Un-Biased 1.87E E E E E E E E-08 Ps90%/90% (+KTL) Un-Biased 3.01E E E E E E E E-07 Ps90%/90% (-KTL) Un-Biased 1.99E E E E E E E E-07 Specification MIN -4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS 187

188 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Positive Input Bias #3 (A) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Positive Input Bias #3 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 188

189 Table Raw data for Positive Input Bias #3 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Input Bias #3 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-07 Biased Statistics Average Biased 2.62E E E E E E E E-07 Std Dev Biased 2.49E E E E E E E E-08 Ps90%/90% (+KTL) Biased 3.30E E E E E E E E-07 Ps90%/90% (-KTL) Biased 1.94E E E E E E E E-07 Un-Biased Statistics Average Un-Biased 2.54E E E E E E E E-07 Std Dev Un-Biased 1.67E E E E E E E E-08 Ps90%/90% (+KTL) Un-Biased 3.00E E E E E E E E-07 Ps90%/90% (-KTL) Un-Biased 2.08E E E E E E E E-07 Specification MIN -4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS 189

190 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Positive Input Bias #4 (A) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Positive Input Bias #4 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 190

191 Table Raw data for Positive Input Bias #4 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Input Bias #4 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-07 Biased Statistics Average Biased 2.70E E E E E E E E-07 Std Dev Biased 1.22E E E E E E E E-08 Ps90%/90% (+KTL) Biased 3.04E E E E E E E E-07 Ps90%/90% (-KTL) Biased 2.36E E E E E E E E-07 Un-Biased Statistics Average Un-Biased 2.52E E E E E E E E-07 Std Dev Un-Biased 1.79E E E E E E E E-08 Ps90%/90% (+KTL) Un-Biased 3.01E E E E E E E E-07 Ps90%/90% (-KTL) Un-Biased 2.03E E E E E E E E-07 Specification MIN -4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS 191

192 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Negative Input Bias #1 (A) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Negative Input Bias #1 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 192

193 Table Raw data for Negative Input Bias #1 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Input Bias #1 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-07 Biased Statistics Average Biased 2.64E E E E E E E E-07 Std Dev Biased 1.52E E E E E E E E-08 Ps90%/90% (+KTL) Biased 3.06E E E E E E E E-07 Ps90%/90% (-KTL) Biased 2.22E E E E E E E E-07 Un-Biased Statistics Average Un-Biased 2.44E E E E E E E E-07 Std Dev Un-Biased 1.95E E E E E E E E-08 Ps90%/90% (+KTL) Un-Biased 2.97E E E E E E E E-07 Ps90%/90% (-KTL) Un-Biased 1.91E E E E E E E E-07 Specification MIN -4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS 193

194 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Negative Input Bias #2 (A) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Negative Input Bias #2 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 194

195 Table Raw data for Negative Input Bias #2 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Input Bias #2 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-07 Biased Statistics Average Biased 2.56E E E E E E E E-07 Std Dev Biased 1.82E E E E E E E E-08 Ps90%/90% (+KTL) Biased 3.06E E E E E E E E-07 Ps90%/90% (-KTL) Biased 2.06E E E E E E E E-07 Un-Biased Statistics Average Un-Biased 2.46E E E E E E E E-07 Std Dev Un-Biased 2.51E E E E E E E E-08 Ps90%/90% (+KTL) Un-Biased 3.15E E E E E E E E-07 Ps90%/90% (-KTL) Un-Biased 1.77E E E E E E E E-07 Specification MIN -4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS 195

196 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Negative Input Bias #3 (A) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Negative Input Bias #3 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 196

197 Table Raw data for Negative Input Bias #3 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Input Bias #3 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-07 Biased Statistics Average Biased 2.62E E E E E E E E-07 Std Dev Biased 2.49E E E E E E E E-08 Ps90%/90% (+KTL) Biased 3.30E E E E E E E E-07 Ps90%/90% (-KTL) Biased 1.94E E E E E E E E-07 Un-Biased Statistics Average Un-Biased 2.58E E E E E E E E-07 Std Dev Un-Biased 1.92E E E E E E E E-08 Ps90%/90% (+KTL) Un-Biased 3.11E E E E E E E E-07 Ps90%/90% (-KTL) Un-Biased 2.05E E E E E E E E-07 Specification MIN -4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS 197

198 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Negative Input Bias #4 (A) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Negative Input Bias #4 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 198

199 Table Raw data for Negative Input Bias #4 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Input Bias #4 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-07 Biased Statistics Average Biased 2.66E E E E E E E E-07 Std Dev Biased 8.94E E E E E E E E-08 Ps90%/90% (+KTL) Biased 2.91E E E E E E E E-07 Ps90%/90% (-KTL) Biased 2.41E E E E E E E E-07 Un-Biased Statistics Average Un-Biased 2.38E E E E E E E E-07 Std Dev Un-Biased 1.79E E E E E E E E-08 Ps90%/90% (+KTL) Un-Biased 2.87E E E E E E E E-07 Ps90%/90% (-KTL) Un-Biased 1.89E E E E E E E E-07 Specification MIN -4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS 199

200 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Common Mode Rejection #1 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Common Mode Rejection #1 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 200

201 Table Raw data for Common Mode Rejection #1 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Common Mode Rejection #1 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+01 Biased Statistics Average Biased 9.67E E E E E E E E+01 Std Dev Biased 7.30E E E E E E E E+00 Ps90%/90% (+KTL) Biased 9.87E E E E E E E E+02 Ps90%/90% (-KTL) Biased 9.47E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 9.68E E E E E E E E+01 Std Dev Un-Biased 7.51E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 9.88E E E E E E E E+01 Ps90%/90% (-KTL) Un-Biased 9.47E E E E E E E E+01 Specification MIN 7.30E E E E E E E E+01 Status PASS PASS PASS N/A N/A PASS PASS PASS 201

202 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Common Mode Rejection #2 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Common Mode Rejection #2 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 202

203 Table Raw data for Common Mode Rejection #2 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Common Mode Rejection #2 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+01 Biased Statistics Average Biased 9.65E E E E E E E E+01 Std Dev Biased 1.31E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.00E E E E E E E E+02 Ps90%/90% (-KTL) Biased 9.29E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 9.71E E E E E E E E+01 Std Dev Un-Biased 7.21E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 9.91E E E E E E E E+01 Ps90%/90% (-KTL) Un-Biased 9.51E E E E E E E E+01 Specification MIN 7.30E E E E E E E E+01 Status PASS PASS PASS N/A N/A PASS PASS PASS 203

204 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Common Mode Rejection #3 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Common Mode Rejection #3 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 204

205 Table Raw data for Common Mode Rejection #3 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Common Mode Rejection #3 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+01 Biased Statistics Average Biased 9.70E E E E E E E E+01 Std Dev Biased 9.86E E E E E E E E+00 Ps90%/90% (+KTL) Biased 9.97E E E E E E E E+02 Ps90%/90% (-KTL) Biased 9.43E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 9.71E E E E E E E E+01 Std Dev Un-Biased 1.16E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.00E E E E E E E E+01 Ps90%/90% (-KTL) Un-Biased 9.39E E E E E E E E+01 Specification MIN 7.30E E E E E E E E+01 Status PASS PASS PASS N/A N/A PASS PASS PASS 205

206 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Common Mode Rejection #4 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Common Mode Rejection #4 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 206

207 Table Raw data for Common Mode Rejection #4 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Common Mode Rejection #4 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+01 Biased Statistics Average Biased 9.65E E E E E E E E+01 Std Dev Biased 1.35E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.00E E E E E E E E+02 Ps90%/90% (-KTL) Biased 9.28E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 9.76E E E E E E E E+01 Std Dev Un-Biased 8.77E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 1.00E E E E E E E E+01 Ps90%/90% (-KTL) Un-Biased 9.52E E E E E E E E+01 Specification MIN 7.30E E E E E E E E+01 Status PASS PASS PASS N/A N/A PASS PASS PASS 207

208 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Large Signal Voltage RL=500 #1 (V/mV) 3.50E E E E E E E E hr hr 70 Figure Plot of Large Signal Voltage RL=500 #1 (V/mV) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 208

209 Table Raw data for Large Signal Voltage RL=500 #1 (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Large Signal Voltage RL=500 #1 (V/mV) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 2.99E E E E E E E E+00 Std Dev Biased 4.79E E E E E E E E-01 Ps90%/90% (+KTL) Biased 3.12E E E E E E E E+00 Ps90%/90% (-KTL) Biased 2.86E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 3.11E E E E E E E E+00 Std Dev Un-Biased 2.10E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 3.69E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 2.54E E E E E E E E+00 Specification MIN 1.00E E E E E E E E-01 Status PASS PASS PASS N/A N/A PASS PASS PASS 209

210 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Large Signal Voltage RL=500 #2 (V/mV) 3.50E E E E E E E E hr hr 70 Figure Plot of Large Signal Voltage RL=500 #2 (V/mV) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 210

211 Table Raw data for Large Signal Voltage RL=500 #2 (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Large Signal Voltage RL=500 #2 (V/mV) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 2.99E E E E E E E E+00 Std Dev Biased 4.99E E E E E E E E-01 Ps90%/90% (+KTL) Biased 3.13E E E E E E E E+00 Ps90%/90% (-KTL) Biased 2.85E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 3.05E E E E E E E E+00 Std Dev Un-Biased 1.50E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 3.46E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 2.64E E E E E E E E+00 Specification MIN 1.00E E E E E E E E-01 Status PASS PASS PASS N/A N/A PASS PASS PASS 211

212 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Large Signal Voltage RL=500 #3 (V/mV) 3.50E E E E E E E E hr hr 70 Figure Plot of Large Signal Voltage RL=500 #3 (V/mV) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 212

213 Table Raw data for Large Signal Voltage RL=500 #3 (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Large Signal Voltage RL=500 #3 (V/mV) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 3.01E E E E E E E E+00 Std Dev Biased 7.23E E E E E E E E-01 Ps90%/90% (+KTL) Biased 3.21E E E E E E E E+00 Ps90%/90% (-KTL) Biased 2.82E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 3.10E E E E E E E E+00 Std Dev Un-Biased 1.69E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 3.56E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 2.64E E E E E E E E+00 Specification MIN 1.00E E E E E E E E-01 Status PASS PASS PASS N/A N/A PASS PASS PASS 213

214 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Large Signal Voltage RL=500 #4 (V/mV) 3.50E E E E E E E E hr hr 70 Figure Plot of Large Signal Voltage RL=500 #4 (V/mV) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 214

215 Table Raw data for Large Signal Voltage RL=500 #4 (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Large Signal Voltage RL=500 #4 (V/mV) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 2.96E E E E E E E E+00 Std Dev Biased 5.96E E E E E E E E-01 Ps90%/90% (+KTL) Biased 3.12E E E E E E E E+00 Ps90%/90% (-KTL) Biased 2.80E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 3.08E E E E E E E E+00 Std Dev Un-Biased 1.84E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 3.58E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 2.57E E E E E E E E+00 Specification MIN 1.00E E E E E E E E-01 Status PASS PASS PASS N/A N/A PASS PASS PASS 215

216 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Large Signal Voltage RL=100 #1 (V/mV) 3.00E E E E E E E hr hr 70 Figure Plot of Large Signal Voltage RL=100 #1 (V/mV) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 216

217 Table Raw data for Large Signal Voltage RL=100 #1 (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Large Signal Voltage RL=100 #1 (V/mV) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 2.47E E E E E E E E+00 Std Dev Biased 4.75E E E E E E E E-01 Ps90%/90% (+KTL) Biased 2.60E E E E E E E E+00 Ps90%/90% (-KTL) Biased 2.34E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 2.57E E E E E E E E+00 Std Dev Un-Biased 1.59E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 3.01E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 2.13E E E E E E E E+00 Specification MIN 7.00E E E E E E E E-01 Status PASS PASS PASS N/A N/A PASS PASS PASS 217

218 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Large Signal Voltage RL=100 #2 (V/mV) 3.00E E E E E E E hr hr 70 Figure Plot of Large Signal Voltage RL=100 #2 (V/mV) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 218

219 Table Raw data for Large Signal Voltage RL=100 #2 (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Large Signal Voltage RL=100 #2 (V/mV) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 2.46E E E E E E E E+00 Std Dev Biased 5.00E E E E E E E E-01 Ps90%/90% (+KTL) Biased 2.60E E E E E E E E+00 Ps90%/90% (-KTL) Biased 2.32E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 2.52E E E E E E E E+00 Std Dev Un-Biased 1.15E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 2.84E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 2.20E E E E E E E E+00 Specification MIN 7.00E E E E E E E E-01 Status PASS PASS PASS N/A N/A PASS PASS PASS 219

220 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Large Signal Voltage RL=100 #3 (V/mV) 3.00E E E E E E E hr hr 70 Figure Plot of Large Signal Voltage RL=100 #3 (V/mV) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 220

221 Table Raw data for Large Signal Voltage RL=100 #3 (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Large Signal Voltage RL=100 #3 (V/mV) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 2.49E E E E E E E E+00 Std Dev Biased 7.34E E E E E E E E-01 Ps90%/90% (+KTL) Biased 2.69E E E E E E E E+00 Ps90%/90% (-KTL) Biased 2.28E E E E E E E E-01 Un-Biased Statistics Average Un-Biased 2.56E E E E E E E E+00 Std Dev Un-Biased 1.32E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 2.93E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 2.20E E E E E E E E+00 Specification MIN 7.00E E E E E E E E-01 Status PASS PASS PASS N/A N/A PASS PASS PASS 221

222 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Large Signal Voltage RL=100 #4 (V/mV) 3.00E E E E E E E hr hr 70 Figure Plot of Large Signal Voltage RL=100 #4 (V/mV) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 222

223 Table Raw data for Large Signal Voltage RL=100 #4 (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Large Signal Voltage RL=100 #4 (V/mV) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 2.45E E E E E E E E+00 Std Dev Biased 6.33E E E E E E E E-01 Ps90%/90% (+KTL) Biased 2.62E E E E E E E E+00 Ps90%/90% (-KTL) Biased 2.27E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 2.53E E E E E E E E+00 Std Dev Un-Biased 1.38E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 2.91E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 2.16E E E E E E E E+00 Specification MIN 7.00E E E E E E E E-01 Status PASS PASS PASS N/A N/A PASS PASS PASS 223

224 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 1.20E+02 Channel 1:2 (db) 1.00E E E E E E hr hr 70 Figure Plot of Channel 1:2 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 224

225 Table Raw data for Channel 1:2 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 1:2 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.05E E E E E E E E+02 Std Dev Biased 4.90E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.18E E E E E E E E+02 Ps90%/90% (-KTL) Biased 9.12E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.11E E E E E E E E+02 Std Dev Un-Biased 4.20E E E E E E E E+01 Ps90%/90% (+KTL) Un-Biased 1.22E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 9.91E E E E E E E E+01 Specification MIN 8.10E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 225

226 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 1.40E+02 Ps90%/90% (-KTL) Un-Biased Specification MIN Channel 1:3 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 1:3 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 226

227 Table Raw data for Channel 1:3 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 1:3 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+01 Biased Statistics Average Biased 1.11E E E E E E E E+02 Std Dev Biased 1.03E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.39E E E E E E E E+02 Ps90%/90% (-KTL) Biased 8.24E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.09E E E E E E E E+02 Std Dev Un-Biased 9.63E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.36E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 8.30E E E E E E E E+01 Specification MIN 8.10E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 227

228 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 1.40E+02 Ps90%/90% (-KTL) Un-Biased Specification MIN Channel 1:4 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 1:4 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 228

229 Table Raw data for Channel 1:4 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 1:4 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.07E E E E E E E E+02 Std Dev Biased 1.09E E E E E E E E+01 Ps90%/90% (+KTL) Biased 1.37E E E E E E E E+02 Ps90%/90% (-KTL) Biased 7.75E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.02E E E E E E E E+02 Std Dev Un-Biased 4.91E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.16E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 8.87E E E E E E E E+01 Specification MIN 8.10E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 229

230 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 1.40E+02 Ps90%/90% (-KTL) Un-Biased Specification MIN Channel 2:1 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 2:1 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 230

231 Table Raw data for Channel 2:1 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 2:1 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.09E E E E E E E E+02 Std Dev Biased 6.59E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.27E E E E E E E E+02 Ps90%/90% (-KTL) Biased 9.09E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.05E E E E E E E E+02 Std Dev Un-Biased 5.75E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.21E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 8.94E E E E E E E E+01 Specification MIN 8.10E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 231

232 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 1.40E+02 Ps90%/90% (-KTL) Un-Biased Specification MIN Channel 2:3 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 2:3 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 232

233 Table Raw data for Channel 2:3 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 2:3 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+01 Biased Statistics Average Biased 1.13E E E E E E E E+02 Std Dev Biased 1.10E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.43E E E E E E E E+02 Ps90%/90% (-KTL) Biased 8.33E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.03E E E E E E E E+02 Std Dev Un-Biased 7.01E E E E E E E E+01 Ps90%/90% (+KTL) Un-Biased 1.22E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 8.35E E E E E E E E+01 Specification MIN 8.10E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 233

234 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 1.40E+02 Ps90%/90% (-KTL) Un-Biased Specification MIN Channel 2:4 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 2:4 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 234

235 Table Raw data for Channel 2:4 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 2:4 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.09E E E E E E E E+02 Std Dev Biased 8.87E E E E E E E E+01 Ps90%/90% (+KTL) Biased 1.33E E E E E E E E+02 Ps90%/90% (-KTL) Biased 8.42E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.10E E E E E E E E+02 Std Dev Un-Biased 7.16E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.29E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 9.00E E E E E E E E+01 Specification MIN 8.10E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 235

236 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 1.40E+02 Ps90%/90% (-KTL) Un-Biased Specification MIN Channel 3:1 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 3:1 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 236

237 Table Raw data for Channel 3:1 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 3:1 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.09E E E E E E E E+02 Std Dev Biased 5.33E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.24E E E E E E E E+02 Ps90%/90% (-KTL) Biased 9.47E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.12E E E E E E E E+02 Std Dev Un-Biased 1.76E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.60E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 6.40E E E E E E E E+01 Specification MIN 8.10E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 237

238 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 1.40E+02 Ps90%/90% (-KTL) Un-Biased Specification MIN Channel 3:2 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 3:2 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 238

239 Table Raw data for Channel 3:2 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 3:2 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.05E E E E E E E E+02 Std Dev Biased 7.10E E E E E E E E+01 Ps90%/90% (+KTL) Biased 1.24E E E E E E E E+02 Ps90%/90% (-KTL) Biased 8.55E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.15E E E E E E E E+02 Std Dev Un-Biased 2.36E E E E E E E E+01 Ps90%/90% (+KTL) Un-Biased 1.80E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 5.02E E E E E E E E+01 Specification MIN 8.10E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 239

240 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 1.20E+02 Ps90%/90% (-KTL) Un-Biased Specification MIN Channel 3:4 (db) 1.00E E E E E E hr hr 70 Figure Plot of Channel 3:4 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 240

241 Table Raw data for Channel 3:4 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 3:4 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.12E E E E E E E E+02 Std Dev Biased 9.67E E E E E E E E+01 Ps90%/90% (+KTL) Biased 1.39E E E E E E E E+02 Ps90%/90% (-KTL) Biased 8.58E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.08E E E E E E E E+02 Std Dev Un-Biased 8.58E E E E E E E E+01 Ps90%/90% (+KTL) Un-Biased 1.32E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 8.46E E E E E E E E+01 Specification MIN 8.10E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 241

242 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 1.40E+02 Ps90%/90% (-KTL) Un-Biased Specification MIN Channel 4:1 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 4:1 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 242

243 Table Raw data for Channel 4:1 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 4:1 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.09E E E E E E E E+02 Std Dev Biased 1.10E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.40E E E E E E E E+02 Ps90%/90% (-KTL) Biased 7.92E E E E E E E E+02 Un-Biased Statistics Average Un-Biased 1.18E E E E E E E E+02 Std Dev Un-Biased 1.24E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.52E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 8.42E E E E E E E E+01 Specification MIN 8.10E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 243

244 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 1.40E+02 Ps90%/90% (-KTL) Un-Biased Specification MIN Channel 4:2 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 4:2 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 244

245 Table Raw data for Channel 4:2 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 4:2 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.00E E E E E E E E+02 Std Dev Biased 3.45E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.10E E E E E E E E+02 Ps90%/90% (-KTL) Biased 9.10E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.07E E E E E E E E+02 Std Dev Un-Biased 3.51E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.17E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 9.76E E E E E E E E+01 Specification MIN 8.10E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 245

246 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 1.40E+02 Ps90%/90% (-KTL) Un-Biased Specification MIN Channel 4:3 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 4:3 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 246

247 Table Raw data for Channel 4:3 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 4:3 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.07E E E E E E E E+02 Std Dev Biased 4.64E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.20E E E E E E E E+02 Ps90%/90% (-KTL) Biased 9.41E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.23E E E E E E E E+02 Std Dev Un-Biased 1.43E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.63E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 8.39E E E E E E E E+01 Specification MIN 8.10E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 247

248 Output Voltage Swing RL=500 #1 (V) 4.15E E E E E E E E E+00 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN hr hr 70 Figure Plot of Output Voltage Swing RL=500 #1 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 248

249 Table Raw data for Output Voltage Swing RL=500 #1 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=500 #1 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 4.11E E E E E E E E+00 Std Dev Biased 1.64E E E E E E E E-03 Ps90%/90% (+KTL) Biased 4.12E E E E E E E E+00 Ps90%/90% (-KTL) Biased 4.11E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 4.12E E E E E E E E+00 Std Dev Un-Biased 2.95E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 4.13E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 4.11E E E E E E E E+00 Specification MIN 3.90E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 249

250 Output Voltage Swing RL=500 #2 (V) 4.15E E E E E E E E E+00 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN hr hr 70 Figure Plot of Output Voltage Swing RL=500 #2 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 250

251 Table Raw data for Output Voltage Swing RL=500 #2 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=500 #2 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 4.11E E E E E E E E+00 Std Dev Biased 1.95E E E E E E E E-03 Ps90%/90% (+KTL) Biased 4.12E E E E E E E E+00 Ps90%/90% (-KTL) Biased 4.11E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 4.12E E E E E E E E+00 Std Dev Un-Biased 3.65E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 4.13E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 4.11E E E E E E E E+00 Specification MIN 3.90E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 251

252 Output Voltage Swing RL=500 #3 (V) 4.15E E E E E E E E E+00 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN hr hr 70 Figure Plot of Output Voltage Swing RL=500 #3 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 252

253 Table Raw data for Output Voltage Swing RL=500 #3 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=500 #3 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 4.11E E E E E E E E+00 Std Dev Biased 2.70E E E E E E E E-03 Ps90%/90% (+KTL) Biased 4.12E E E E E E E E+00 Ps90%/90% (-KTL) Biased 4.11E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 4.12E E E E E E E E+00 Std Dev Un-Biased 3.67E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 4.13E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 4.11E E E E E E E E+00 Specification MIN 3.90E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 253

254 Output Voltage Swing RL=500 #4 (V) 4.15E E E E E E E E E+00 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN hr hr 70 Figure Plot of Output Voltage Swing RL=500 #4 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 254

255 Table Raw data for Output Voltage Swing RL=500 #4 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=500 #4 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 4.11E E E E E E E E+00 Std Dev Biased 1.52E E E E E E E E-03 Ps90%/90% (+KTL) Biased 4.12E E E E E E E E+00 Ps90%/90% (-KTL) Biased 4.11E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 4.12E E E E E E E E+00 Std Dev Un-Biased 2.45E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 4.12E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 4.11E E E E E E E E+00 Specification MIN 3.90E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 255

256 Output Voltage Swing RL=100 #1 (V) 4.00E E E E E E E E E E E+00 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN hr hr 70 Figure Plot of Output Voltage Swing RL=100 #1 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 256

257 Table Raw data for Output Voltage Swing RL=100 #1 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=100 #1 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 3.94E E E E E E E E+00 Std Dev Biased 8.94E E E E E E E E-04 Ps90%/90% (+KTL) Biased 3.94E E E E E E E E+00 Ps90%/90% (-KTL) Biased 3.93E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 3.94E E E E E E E E+00 Std Dev Un-Biased 2.05E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 3.94E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 3.93E E E E E E E E+00 Specification MIN 3.70E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 257

258 Output Voltage Swing RL=100 #2 (V) 4.00E E E E E E E E E E E+00 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN hr hr 70 Figure Plot of Output Voltage Swing RL=100 #2 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 258

259 Table Raw data for Output Voltage Swing RL=100 #2 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=100 #2 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 3.94E E E E E E E E+00 Std Dev Biased 1.67E E E E E E E E-03 Ps90%/90% (+KTL) Biased 3.94E E E E E E E E+00 Ps90%/90% (-KTL) Biased 3.93E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 3.94E E E E E E E E+00 Std Dev Un-Biased 1.52E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 3.94E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 3.93E E E E E E E E+00 Specification MIN 3.70E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 259

260 Output Voltage Swing RL=100 #3 (V) 4.00E E E E E E E E E E E+00 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN hr hr 70 Figure Plot of Output Voltage Swing RL=100 #3 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 260

261 Table Raw data for Output Voltage Swing RL=100 #3 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=100 #3 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 3.94E E E E E E E E+00 Std Dev Biased 1.48E E E E E E E E-03 Ps90%/90% (+KTL) Biased 3.94E E E E E E E E+00 Ps90%/90% (-KTL) Biased 3.93E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 3.94E E E E E E E E+00 Std Dev Un-Biased 1.79E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 3.94E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 3.93E E E E E E E E+00 Specification MIN 3.70E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 261

262 Output Voltage Swing RL=100 #4 (V) 4.00E E E E E E E E E E E+00 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN hr hr 70 Figure Plot of Output Voltage Swing RL=100 #4 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 262

263 Table Raw data for Output Voltage Swing RL=100 #4 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=100 #4 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 3.94E E E E E E E E+00 Std Dev Biased 1.34E E E E E E E E-03 Ps90%/90% (+KTL) Biased 3.94E E E E E E E E+00 Ps90%/90% (-KTL) Biased 3.93E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 3.94E E E E E E E E+00 Std Dev Un-Biased 1.82E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 3.94E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 3.93E E E E E E E E+00 Specification MIN 3.70E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 263

264 Output Voltage Swing RL=500 #1 (V) 1.40E E E E E E E E+00 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX hr hr 70 Figure Plot of Output Voltage Swing RL=500 #1 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 264

265 Table Raw data for Output Voltage Swing RL=500 #1 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=500 #1 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-01 Biased Statistics Average Biased 8.92E E E E E E E E-01 Std Dev Biased 1.79E E E E E E E E-03 Ps90%/90% (+KTL) Biased 8.97E E E E E E E E-01 Ps90%/90% (-KTL) Biased 8.87E E E E E E E E-01 Un-Biased Statistics Average Un-Biased 8.87E E E E E E E E-01 Std Dev Un-Biased 2.59E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 8.94E E E E E E E E-01 Ps90%/90% (-KTL) Un-Biased 8.80E E E E E E E E-01 Specification MAX 1.10E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 265

266 Output Voltage Swing RL=500 #2 (V) 1.40E E E E E E E E+00 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX hr hr 70 Figure Plot of Output Voltage Swing RL=500 #2 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 266

267 Table Raw data for Output Voltage Swing RL=500 #2 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=500 #2 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-01 Biased Statistics Average Biased 8.92E E E E E E E E-01 Std Dev Biased 2.39E E E E E E E E-03 Ps90%/90% (+KTL) Biased 8.99E E E E E E E E-01 Ps90%/90% (-KTL) Biased 8.86E E E E E E E E-01 Un-Biased Statistics Average Un-Biased 8.90E E E E E E E E-01 Std Dev Un-Biased 3.97E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 9.00E E E E E E E E-01 Ps90%/90% (-KTL) Un-Biased 8.79E E E E E E E E-01 Specification MAX 1.10E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 267

268 Output Voltage Swing RL=500 #3 (V) 1.40E E E E E E E E+00 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX hr hr 70 Figure Plot of Output Voltage Swing RL=500 #3 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 268

269 Table Raw data for Output Voltage Swing RL=500 #3 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=500 #3 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-01 Biased Statistics Average Biased 8.92E E E E E E E E-01 Std Dev Biased 1.82E E E E E E E E-03 Ps90%/90% (+KTL) Biased 8.97E E E E E E E E-01 Ps90%/90% (-KTL) Biased 8.87E E E E E E E E-01 Un-Biased Statistics Average Un-Biased 8.89E E E E E E E E-01 Std Dev Un-Biased 4.66E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 9.02E E E E E E E E-01 Ps90%/90% (-KTL) Un-Biased 8.76E E E E E E E E-01 Specification MAX 1.10E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 269

270 Output Voltage Swing RL=500 #4 (V) 1.40E E E E E E E E+00 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX hr hr 70 Figure Plot of Output Voltage Swing RL=500 #4 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 270

271 Table Raw data for Output Voltage Swing RL=500 #4 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=500 #4 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-01 Biased Statistics Average Biased 8.93E E E E E E E E-01 Std Dev Biased 1.22E E E E E E E E-03 Ps90%/90% (+KTL) Biased 8.96E E E E E E E E-01 Ps90%/90% (-KTL) Biased 8.90E E E E E E E E-01 Un-Biased Statistics Average Un-Biased 8.87E E E E E E E E-01 Std Dev Un-Biased 2.70E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 8.95E E E E E E E E-01 Ps90%/90% (-KTL) Un-Biased 8.80E E E E E E E E-01 Specification MAX 1.10E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 271

272 Output Voltage Swing RL=100 #1 (V) 1.60E E E E E E E E E+00 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX hr hr 70 Figure Plot of Output Voltage Swing RL=100 #1 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 272

273 Table Raw data for Output Voltage Swing RL=100 #1 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=100 #1 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 1.07E E E E E E E E+00 Std Dev Biased 5.48E E E E E E E E-03 Ps90%/90% (+KTL) Biased 1.07E E E E E E E E+00 Ps90%/90% (-KTL) Biased 1.07E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 1.07E E E E E E E E+00 Std Dev Un-Biased 1.92E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 1.07E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 1.06E E E E E E E E+00 Specification MAX 1.30E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 273

274 Output Voltage Swing RL=100 #2 (V) 1.60E E E E E E E E E+00 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX hr hr 70 Figure Plot of Output Voltage Swing RL=100 #2 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 274

275 Table Raw data for Output Voltage Swing RL=100 #2 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=100 #2 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 1.07E E E E E E E E+00 Std Dev Biased 1.10E E E E E E E E-03 Ps90%/90% (+KTL) Biased 1.07E E E E E E E E+00 Ps90%/90% (-KTL) Biased 1.07E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 1.07E E E E E E E E+00 Std Dev Un-Biased 1.34E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 1.07E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 1.07E E E E E E E E+00 Specification MAX 1.30E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 275

276 Output Voltage Swing RL=100 #3 (V) 1.60E E E E E E E E E+00 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX hr hr 70 Figure Plot of Output Voltage Swing RL=100 #3 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 276

277 Table Raw data for Output Voltage Swing RL=100 #3 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=100 #3 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 1.07E E E E E E E E+00 Std Dev Biased 8.37E E E E E E E E-03 Ps90%/90% (+KTL) Biased 1.07E E E E E E E E+00 Ps90%/90% (-KTL) Biased 1.07E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 1.07E E E E E E E E+00 Std Dev Un-Biased 1.87E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 1.07E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 1.06E E E E E E E E+00 Specification MAX 1.30E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 277

278 Output Voltage Swing RL=100 #4 (V) 1.60E E E E E E E E E+00 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX hr hr 70 Figure Plot of Output Voltage Swing RL=100 #4 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 278

279 Table Raw data for Output Voltage Swing RL=100 #4 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=100 #4 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 1.07E E E E E E E E+00 Std Dev Biased 8.37E E E E E E E E-03 Ps90%/90% (+KTL) Biased 1.07E E E E E E E E+00 Ps90%/90% (-KTL) Biased 1.07E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 1.07E E E E E E E E+00 Std Dev Un-Biased 2.07E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 1.07E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 1.06E E E E E E E E+00 Specification MAX 1.30E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 279

280 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 4.50E-02 Ps90%/90% (-KTL) Un-Biased Specification MIN Maximum Output Source #1 (A) 4.00E E E E E E E E E hr hr 70 Figure Plot of Maximum Output Source #1 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 280

281 Table Raw data for Maximum Output Source #1 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Maximum Output Source #1 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased 4.09E E E E E E E E-02 Std Dev Biased 3.28E E E E E E E E-04 Ps90%/90% (+KTL) Biased 4.18E E E E E E E E-02 Ps90%/90% (-KTL) Biased 4.00E E E E E E E E-02 Un-Biased Statistics Average Un-Biased 4.12E E E E E E E E-02 Std Dev Un-Biased 6.08E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 4.29E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased 3.96E E E E E E E E-02 Specification MIN 2.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 281

282 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 4.50E-02 Ps90%/90% (-KTL) Un-Biased Specification MIN Maximum Output Source #2 (A) 4.00E E E E E E E E E hr hr 70 Figure Plot of Maximum Output Source #2 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 282

283 Table Raw data for Maximum Output Source #2 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Maximum Output Source #2 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased 4.10E E E E E E E E-02 Std Dev Biased 5.47E E E E E E E E-04 Ps90%/90% (+KTL) Biased 4.24E E E E E E E E-02 Ps90%/90% (-KTL) Biased 3.95E E E E E E E E-02 Un-Biased Statistics Average Un-Biased 4.09E E E E E E E E-02 Std Dev Un-Biased 3.95E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 4.19E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased 3.98E E E E E E E E-02 Specification MIN 2.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 283

284 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 4.50E-02 Ps90%/90% (-KTL) Un-Biased Specification MIN Maximum Output Source #3 (A) 4.00E E E E E E E E E hr hr 70 Figure Plot of Maximum Output Source #3 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 284

285 Table Raw data for Maximum Output Source #3 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Maximum Output Source #3 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased 4.11E E E E E E E E-02 Std Dev Biased 6.15E E E E E E E E-04 Ps90%/90% (+KTL) Biased 4.28E E E E E E E E-02 Ps90%/90% (-KTL) Biased 3.94E E E E E E E E-02 Un-Biased Statistics Average Un-Biased 4.09E E E E E E E E-02 Std Dev Un-Biased 3.58E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 4.19E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased 4.00E E E E E E E E-02 Specification MIN 2.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 285

286 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 4.50E-02 Ps90%/90% (-KTL) Un-Biased Specification MIN Maximum Output Source #4 (A) 4.00E E E E E E E E E hr hr 70 Figure Plot of Maximum Output Source #4 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 286

287 Table Raw data for Maximum Output Source #4 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Maximum Output Source #4 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased 4.10E E E E E E E E-02 Std Dev Biased 4.05E E E E E E E E-04 Ps90%/90% (+KTL) Biased 4.21E E E E E E E E-02 Ps90%/90% (-KTL) Biased 3.99E E E E E E E E-02 Un-Biased Statistics Average Un-Biased 4.13E E E E E E E E-02 Std Dev Un-Biased 5.35E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 4.27E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased 3.98E E E E E E E E-02 Specification MIN 2.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 287

288 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased 0.00E+00 Ps90%/90% (+KTL) Un-Biased Specification MAX Maximum Output Sink #1 (A) -5.00E E E E E E E E E hr 168-hr Figure Plot of Maximum Output Sink #1 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 288

289 Table Raw data for Maximum Output Sink #1 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Maximum Output Sink #1 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased -3.84E E E E E E E E-02 Std Dev Biased 1.09E E E E E E E E-04 Ps90%/90% (+KTL) Biased -3.81E E E E E E E E-02 Ps90%/90% (-KTL) Biased -3.87E E E E E E E E-02 Un-Biased Statistics Average Un-Biased -3.87E E E E E E E E-02 Std Dev Un-Biased 3.93E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased -3.76E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased -3.98E E E E E E E E-02 Specification MAX -2.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 289

290 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased 0.00E+00 Ps90%/90% (+KTL) Un-Biased Specification MAX Maximum Output Sink #2 (A) -5.00E E E E E E E E E hr hr 70 Figure Plot of Maximum Output Sink #2 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 290

291 Table Raw data for Maximum Output Sink #2 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Maximum Output Sink #2 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased -3.84E E E E E E E E-02 Std Dev Biased 1.60E E E E E E E E-04 Ps90%/90% (+KTL) Biased -3.80E E E E E E E E-02 Ps90%/90% (-KTL) Biased -3.89E E E E E E E E-02 Un-Biased Statistics Average Un-Biased -3.85E E E E E E E E-02 Std Dev Un-Biased 2.03E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased -3.79E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased -3.91E E E E E E E E-02 Specification MAX -2.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 291

292 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased 0.00E+00 Ps90%/90% (+KTL) Un-Biased Specification MAX Maximum Output Sink #3 (A) -5.00E E E E E E E E E hr 168-hr Figure Plot of Maximum Output Sink #3 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 292

293 Table Raw data for Maximum Output Sink #3 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Maximum Output Sink #3 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased -3.85E E E E E E E E-02 Std Dev Biased 1.80E E E E E E E E-04 Ps90%/90% (+KTL) Biased -3.80E E E E E E E E-02 Ps90%/90% (-KTL) Biased -3.90E E E E E E E E-02 Un-Biased Statistics Average Un-Biased -3.86E E E E E E E E-02 Std Dev Un-Biased 2.18E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased -3.80E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased -3.92E E E E E E E E-02 Specification MAX -2.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 293

294 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased 0.00E+00 Ps90%/90% (+KTL) Un-Biased Specification MAX Maximum Output Sink #4 (A) -5.00E E E E E E E E E hr 168-hr Figure Plot of Maximum Output Sink #4 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 294

295 Table Raw data for Maximum Output Sink #4 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Maximum Output Sink #4 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased -3.84E E E E E E E E-02 Std Dev Biased 1.21E E E E E E E E-04 Ps90%/90% (+KTL) Biased -3.81E E E E E E E E-02 Ps90%/90% (-KTL) Biased -3.88E E E E E E E E-02 Un-Biased Statistics Average Un-Biased -3.87E E E E E E E E-02 Std Dev Un-Biased 3.35E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased -3.78E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased -3.96E E E E E E E E-02 Specification MAX -2.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 295

296 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 9.00E-02 Ps90%/90% (-KTL) Un-Biased Specification MIN Positive Short-Circuit #1 (A) 8.00E E E E E E E E E hr 168-hr Figure Plot of Positive Short-Circuit #1 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 296

297 Table Raw data for Positive Short-Circuit #1 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Short-Circuit #1 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased 8.39E E E E E E E E-02 Std Dev Biased 5.47E E E E E E E E-04 Ps90%/90% (+KTL) Biased 8.54E E E E E E E E-02 Ps90%/90% (-KTL) Biased 8.24E E E E E E E E-02 Un-Biased Statistics Average Un-Biased 8.46E E E E E E E E-02 Std Dev Un-Biased 1.07E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 8.75E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased 8.17E E E E E E E E-02 Specification MIN 5.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 297

298 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 9.00E-02 Ps90%/90% (-KTL) Un-Biased Specification MIN Positive Short-Circuit #2 (A) 8.00E E E E E E E E E hr 168-hr Figure Plot of Positive Short-Circuit #2 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 298

299 Table Raw data for Positive Short-Circuit #2 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Short-Circuit #2 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased 8.42E E E E E E E E-02 Std Dev Biased 1.07E E E E E E E E-03 Ps90%/90% (+KTL) Biased 8.71E E E E E E E E-02 Ps90%/90% (-KTL) Biased 8.13E E E E E E E E-02 Un-Biased Statistics Average Un-Biased 8.40E E E E E E E E-02 Std Dev Un-Biased 7.24E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 8.60E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased 8.20E E E E E E E E-02 Specification MIN 5.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 299

300 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 9.00E-02 Ps90%/90% (-KTL) Un-Biased Specification MIN Positive Short-Circuit #3 (A) 8.00E E E E E E E E E hr 168-hr Figure Plot of Positive Short-Circuit #3 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 300

301 Table Raw data for Positive Short-Circuit #3 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Short-Circuit #3 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased 8.42E E E E E E E E-02 Std Dev Biased 1.13E E E E E E E E-03 Ps90%/90% (+KTL) Biased 8.73E E E E E E E E-02 Ps90%/90% (-KTL) Biased 8.10E E E E E E E E-02 Un-Biased Statistics Average Un-Biased 8.39E E E E E E E E-02 Std Dev Un-Biased 8.07E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 8.61E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased 8.17E E E E E E E E-02 Specification MIN 5.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 301

302 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 9.00E-02 Ps90%/90% (-KTL) Un-Biased Specification MIN Positive Short-Circuit #4 (A) 8.00E E E E E E E E E hr 168-hr Figure Plot of Positive Short-Circuit #4 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 302

303 Table Raw data for Positive Short-Circuit #4 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Short-Circuit #4 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased 8.39E E E E E E E E-02 Std Dev Biased 6.84E E E E E E E E-04 Ps90%/90% (+KTL) Biased 8.57E E E E E E E E-02 Ps90%/90% (-KTL) Biased 8.20E E E E E E E E-02 Un-Biased Statistics Average Un-Biased 8.46E E E E E E E E-02 Std Dev Un-Biased 9.19E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 8.71E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased 8.20E E E E E E E E-02 Specification MIN 5.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 303

304 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased 0.00E+00 Ps90%/90% (+KTL) Un-Biased Specification MAX Negative Short-Circuit #1 (A) -1.00E E E E E E E E E hr 168-hr Figure Plot of Negative Short-Circuit #1 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 304

305 Table Raw data for Negative Short-Circuit #1 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Short-Circuit #1 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased -7.80E E E E E E E E-02 Std Dev Biased 4.78E E E E E E E E-04 Ps90%/90% (+KTL) Biased -7.67E E E E E E E E-02 Ps90%/90% (-KTL) Biased -7.93E E E E E E E E-02 Un-Biased Statistics Average Un-Biased -7.89E E E E E E E E-02 Std Dev Un-Biased 1.07E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased -7.60E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased -8.18E E E E E E E E-02 Specification MAX -5.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 305

306 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased 0.00E+00 Ps90%/90% (+KTL) Un-Biased Specification MAX Negative Short-Circuit #2 (A) -1.00E E E E E E E E E hr 168-hr Figure Plot of Negative Short-Circuit #2 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 306

307 Table Raw data for Negative Short-Circuit #2 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Short-Circuit #2 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased -7.84E E E E E E E E-02 Std Dev Biased 8.43E E E E E E E E-04 Ps90%/90% (+KTL) Biased -7.61E E E E E E E E-02 Ps90%/90% (-KTL) Biased -8.07E E E E E E E E-02 Un-Biased Statistics Average Un-Biased -7.83E E E E E E E E-02 Std Dev Un-Biased 5.54E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased -7.68E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased -7.98E E E E E E E E-02 Specification MAX -5.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 307

308 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased 0.00E+00 Ps90%/90% (+KTL) Un-Biased Specification MAX Negative Short-Circuit #3 (A) -1.00E E E E E E E E E hr 168-hr Figure Plot of Negative Short-Circuit #3 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 308

309 Table Raw data for Negative Short-Circuit #3 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Short-Circuit #3 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased -7.84E E E E E E E E-02 Std Dev Biased 8.69E E E E E E E E-04 Ps90%/90% (+KTL) Biased -7.60E E E E E E E E-02 Ps90%/90% (-KTL) Biased -8.08E E E E E E E E-02 Un-Biased Statistics Average Un-Biased -7.82E E E E E E E E-02 Std Dev Un-Biased 6.49E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased -7.64E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased -8.00E E E E E E E E-02 Specification MAX -5.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 309

310 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased 0.00E+00 Ps90%/90% (+KTL) Un-Biased Specification MAX Negative Short-Circuit #4 (A) -1.00E E E E E E E E E hr 168-hr Figure Plot of Negative Short-Circuit #4 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 310

311 Table Raw data for Negative Short-Circuit #4 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Short-Circuit #4 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased -7.81E E E E E E E E-02 Std Dev Biased 4.21E E E E E E E E-04 Ps90%/90% (+KTL) Biased -7.69E E E E E E E E-02 Ps90%/90% (-KTL) Biased -7.92E E E E E E E E-02 Un-Biased Statistics Average Un-Biased -7.88E E E E E E E E-02 Std Dev Un-Biased 8.67E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased -7.65E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased -8.12E E E E E E E E-02 Specification MAX -5.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 311

312 6.0. Summary / Conclusions The low dose rate testing described in this final report was performed using the facilities at Radiation Assured Devices' Longmire Laboratories in Colorado Springs, CO. The low dose rate source is a GB- 150 irradiator modified to provide a panoramic exposure. The Co-60 rods are held in the base of the irradiator heavily shielded by lead. During the irradiation exposures the rod is raised by an electronic timer/controller and the exposure is performed in air. The dose rate for this irradiator in this configuration ranges from approximately 1mrad(Si)/s to a maximum of approximately 50rad(Si)/s, determined by the distance from the source. The parametric data was obtained as "read and record" and all the raw data plus an attributes summary are contained in this report as well as in a separate Excel file. The attributes data contains the average, standard deviation and the average with the KTL values applied. The KTL value used in this work is per MIL-HDBK-814 using one sided tolerance limits of 90/90 and a 5-piece sample size. The 90/90 KTL values were selected to match the statistical levels specified in the MIL-PRF sampling plan for the qualification of a radiation hardness assured (RHA) component. Note that the following criteria must be met for a device to pass the low dose rate test: following the radiation exposure each of the 5 pieces irradiated under electrical bias shall pass the specification value. The units irradiated without electrical bias and the KTL statistics are included in this report for reference only. If any of the 5 pieces irradiated under electrical bias exceed the datasheet specifications, then the lot could be logged as a failure. Based on this criterion the RH1814MW Quad Operational Amplifier (from the lot date code identified on the first page of this test report) PASSED the enhanced low dose rate sensitivity test to the maximum tested dose level of 50krad(Si) with all parameters remaining within their datasheet specifications. Further, the data in this report can be analyzed along with the high dose rate report titled "Total Ionizing Dose (TID) Radiation Testing of the RH1814MW Quad Op Amp for Linear Technology" to demonstrate that these parts do not exhibit ELDRS as defined in the current test method. 312

313 Appendix A: Photograph of device-under-test to show part markings 313