RF-RXS-B SonNet Wireless Receiver BACnet IP

Transcription

1 Features & Benefits Sensing and controlling without the need of structural cabling Minimal downtime and costs for installation Seamless integration into BACnet IP over Ethernet DIN-rail mounted Easy to install and commission Technical Overview The SonNet Wireless receiver allows quick and seamless integration of SonNet devices into building management systems. It automatically maps data from SonNet end devices into BACnet objects which are transmitted via the vendor independent BACnet IP communication protocol, using a simple web browser interface. Depending on the layout of the SonNet network it can connect up to 40 nodes. Please see the System User manual for more information. The receiver collects data from all other devices on the wireless network, including measurements from sensors, link quality, battery levels for all battery powered devices, hours run for all devices and the current status of all devices. Product Codes Accessories RF-AERIAL-PM2 RF-AERIAL-PM5 Coaxial extension cable for externally mounted aerial 2m length Coaxial extension cable for externally mounted aerial 5m length Specification Radio Output 2.4 GHz, 16 channels automatically selected Direct-sequence spread spectrum Compliance IEEE Aerial Characteristics Gain 3.0dBi VSWR <2:1 Data encryption AES 128 Power supply 24Vdc ±15% 24Vac ±15%, 50/60Hz Communication: USB 2.0 RJ45 Ethernet (for BACnet IP protocol) configured with Auto-MDI-X for 10/100 Mb/s BIBBs supported: DS-RP-B DS-WP-B DM-DDB-B DM-DOB-B DM-DCC-B DS-RPM-B DM-RD-B Environmental: Operating Temp. -10 to +50 C Operating RH 0-90%, non-condensing Storage Temp -10 to +80 C Storage RH 0-90%, non-condensing Dimensions 100 x 95 x 65mm Weight 150g Country of origin UK WEEE Directive: At the end of the products useful life please dispose as per the local regulations. Do not dispose of with normal household waste. Do not burn. The referred to in this data sheet meet the requirements of EU Directive 2014/30/EU Page 1 of 26

2 How it works These receivers are used in conjunction with the Sontay RF-IOM, RF-RR and RF-RS radio sensors and IO modules. Routers are used to route signals from battery powered nodes and other routers to the receiver module, where the signal strength of a direct path is not sufficient for reliable communications. te that RF-IOMs also have full router functionality. Data is transmitted back to the receiver at configurable time intervals, or on a configurable change in measured value. Each sensor retains these configurations if the battery becomes discharged or requires replacement. The receiver automatically selects which of the 16 transmission channels available gives the best radio network performance, taking into account both signal strength and interference levels from adjacent channels and equipment (such as Wi-Fi etc.) The sensors and routers automatically find the best path back to the receiver, which may be directly to the receiver or via parent routers or RF-IOM modules. NB The receiver can support a maximum of 16 directly connected children, a maximum of 12 of which can be battery powered end devices. Each router or RF-IOM module can support a maximum of 16 directly connected children, a maximum of 8 of which can be battery powered end devices. Consideration should be given on network planning for redundancy in case of router failure or damage. A maximum of 40 devices (excl. the receiver) can be mapped into BACnet IP. Installation 1. Remove all packaging from the network receiver and note the MAC address printed on the affixed label. 2. Mount the network receiver in the required position (this will have been determined by the site survey tool, (see the quick start guide and manual for further details), taking care not to site the receiver, and more importantly the aerial, behind any obstruction likely to impede the radio signal. 3. Fix the receiver to the DIN rail. NB If the receiver is to be mounted in a metal enclosure, it is essential that the aerial is mounted externally. A 2 or 5m coaxial extension cable assembly is available for this option. 4. Ensure the antenna is positioned in a vertical alignment. 5. Observe correct polarity if using a 24Vdc power supply. 6. Commissioning of the SonNet wireless network is accomplished using CMS (Configuration and Monitoring Software). 7. Mapping of all BACnet devices and points is accomplished via the receiver s built-in web browser interface. The default IP address is te If the USB port is connected (for commissioning with CMS), the Ethernet port is disabled. Ensure the USB port is disconnected before attempting to communicate via the Ethernet port. A full user guide is supplied with each new network receiver and is also available at Page 2 of 26

3 Electrical connections Aerial LED indication LED indication Button Power supply SonNet Status Data 0V 24V Status BACnet Device Reinitialize LED indication - SonNet Status: ON if there is at least one child node connected on the wireless network, flashes once per second if there are no child nodes present. - Data: Blinking up each time data on the wireless network is received or sent. - BACnet Status: Blinking each time data on the BACnet network is received or sent. Reset Button USB Connector RJ45 Ethernet Push buttons - Reinitialize Device: Resets the Ethernet IP address to the factory default of te it does not affect the Ethernet MAC address or the device BACnet instance - Reset: Resets the wireless network at the receiver. For a short time, until nodes re-join the network, LED D100 will flash once per second. te: The Ethernet is configured to use Auto-MDI-X for 10/100 Mb/s. It should be able to connect to any 10/100 10base-T device, either through a switch or directly to the device without the need for a crossover cable. The Ethernet standard specifies that the maximum 10base-T cable distance is 100 meters. Default home screen for the Page 3 of 26

4 Changing IP settings 1. From the Home page, click on the BACnet/IP Settings link 2. Change the IP address, the IP subnet mask and the IP gateway, if required. Click the appropriate Update button. 3. Change the Device Instance if required. te that the last 3 digits of the device instance form the BACnet device address (005 in the example above). Click the appropriate Update button. 4. Change the Device Location if required. Click the appropriate Update button. 5. Change the BACnet/IP UDP port number if required. Click the appropriate Update button. 6. te changing the settings values may require the to be rebooted. Mapping SonNet Points to BACnet Objects: 1. From the Home page, click on the BACnet/IP Settings link A list of SonNet devices, including the receiver, will appear. te that only the last 8 characters of the SonNet device MAC addresses are displayed. 2. Click the Map Device button to add the BACnet points for each required SonNet device. Page 4 of 26

5 BACnet PICS This document contains the BACnet Protocol Implementation Conformance Statement (PICS) and BACnet Interoperability Building Blocks (BIBBs) for the SonNet BACnet/IP Receiver as required by the American National Standards Institute/ American Society of Heating, Refrigerating, and Air-Conditioning Engineers (ANSI/ASHRAE) Standard , BACnet protocol. BACnet interoperability building blocks are collections of one or more BACnet services. This document includes a listing of the BIBBs currently supported by this device. The SonNet BACnet/IP Receiver is a native BACnet-Application Specific Controller (B-ASC) with BACnet/IP capabilities. Product Description The SonNet devices (wireless) communicate to this Receiver, where the data is received and is modeled by various BACnet objects. The BACnet application, running on the Receiver, will automatically model the SonNet device data to BACnet objects, and will update the Present_Value of each object with data from the SonNet. BACnet Requirements: BACnet Standardized Device Profile (Annex L) BACnet Operator Workstation (B-OWS) BACnet Building Controller (B-BC) BACnet Advanced Application Controller (B-AAC) X BACnet Application Specific Controller (B-ASC) BACnet Smart Sensor (B-SS) BACnet Smart Actuator (B-SA) BACnet Interoperability Building Blocks (BIBBs) (Annex K) The table below lists all the BIBBs that are required for the BACnet Application Specific Controller (B-ASC) profile. The BIBBS that are not required for B-ASC Profile but supported in this product are also listed. Application Services (B-ASC) Data Sharing - Read Property - B Data Sharing - Write Property - B Device Management - Dynamic Device Binding - B Device Management - Dynamic Object Binding - B Device Management - Device Communication Control - B Data Sharing - Read Property Multiple - B Device Management - Reinitialize Device - B BIBB DS-RP-B DS-WP-B DM-DDB-B DM-DOB-B DM-DCC-B DS-RPM-B DM-RD-B Page 5 of 26

6 Standard Device Binding Methods Supported The table below lists all the standard Device Binding methods supported by this device. Send Who-Is, receive I-Am (BIBB DM-DDB-A) X Receive Who-Is, send I-Am (BIBB DM-DDB-B) Send Who-Has, receive I-Have (BIBB DM-DOB-A) X Receive Who-Has, send I-Have (BIBB DM-DOB-B) Manual configuration of recipient device's network number and MAC address ne of the above Standard Object Types Supported The following is a list of the standard object types, as defined by ASHRAE, that are currently supported by this product. This section includes object type details. Analog Input Object Type Dynamically creatable using BACnet's CreateObject service? Dynamically deletable using BACnet's DeleteObject service? Object_Identifier X ANALOG INPUT # Object_Name Yes X "Temperature" Object_Type X ANALOG INPUT Present_Value X Temperature in Degrees Celsius Units X Degrees Celsius Object_Identifier X ANALOG INPUT # Object_Name Yes X "Humidity" Page 6 of 26

7 Object_Type X ANALOG INPUT Present_Value X Relative Humidity in Percent Units X Percent Relative Humidity Object_Identifier X ANALOG INPUT # Object_Name Yes X "CO2" Object_Type X ANALOG INPUT Present_Value X CO2 in Parts Per Million Units X Parts Per Million Object_Identifier X ANALOG INPUT # Object_Name Yes X "Setpoint" Object_Type X ANALOG INPUT Present_Value X Setpoint in Percent Units X Percent Page 7 of 26

8 Object_Identifier X ANALOG INPUT # Object_Name Yes X "Ch.x Measurement" Object_Type X ANALOG INPUT Present_Value X Measurement in Milliamperes, Volts, Ohms, or VFC count Units X Milliamperes, Volts, Ohms, or no units. Analog Value Object Type Dynamically creatable using BACnet's CreateObject service? Dynamically deletable using BACnet's DeleteObject service? Object_Name Yes X RF Channel Present_Value X RF Channel number Units X units Object_Name Yes X Runtime Page 8 of 26

9 Present_Value X Runtime in hours Units X Hours Object_Name Yes X Battery Runtime Present_Value X Runtime in hours Units X Hours Object_Name Yes X "Parent LQI" Present_Value X Link Quality in Percent Units X Percent Page 9 of 26

10 Object_Name Yes X "Sensor Measurement Interval" Present_Value X Interval in Seconds Units X Seconds Object_Name Yes X "Temperature COV" Present_Value X Temperature in Degrees Celsius Units X Degrees Celsius Object_Name Yes X "Humidity COV" Present_Value X Relative Humidity in Percent Units X Percent Relative Humidity Page 10 of 26

11 Object_Name Yes X "CO2 COV" Present_Value X CO2 in Parts Per Million Units X Parts Per Million Object_Name Yes X "Setpoint COV" Present_Value X Setpoint in Percent Units X Percent Object_Name Yes X "PIR Off Delay" Present_Value X Off-Delay in Seconds Page 11 of 26

12 Units X Seconds Object_Name Yes X "VFC Count" Present_Value X VFC Count Units X units Object_Name Yes X "Ch.x Output" Present_Value Yes X 0-10 Volts Units X Volts Object_Name Yes X "Measurement Interval" Page 12 of 26

13 Present_Value X Interval in Seconds Units X Seconds Object_Name Yes X "Ch.x Input COV" Present_Value X 0-10 Volts Units X Volts Object_Name Yes X "Ch.x Upper Alarm" Present_Value X 0-10 Volts Units X Volts Page 13 of 26

14 Object_Name Yes X "Ch.x Lower Alarm" Present_Value X 0-10 Volts Units X Volts Object_Name Yes X "Ch.x Output COV" Present_Value X 0-10 Volts Units X Volts Object_Name Yes X "Ch.x Output Fallback Present_Value Yes X 0-10 Volts Units X Volts Page 14 of 26

15 Binary Input Object Type Dynamically creatable using BACnet's CreateObject service? Dynamically deletable using BACnet's DeleteObject service? Object_Identifier X BINARY INPUT # Object_Name X "Online Status" Object_Type X BINARY INPUT Present_Value X Active=Online, or Inactive=Offline Polarity X rmal Polarity Object_Identifier X BINARY INPUT # Object_Name X "Momentary Switch" Object_Type X BINARY INPUT Present_Value X Active=Closed, or Inactive=Open Polarity X rmal Polarity Object_Identifier X BINARY INPUT # Page 15 of 26

16 Object_Name X "VFC Input" Object_Type X BINARY INPUT Present_Value X Active=Enabled, or Inactive=Disabled Polarity X rmal Polarity Object_Identifier X BINARY INPUT # Object_Name X "PIR" Object_Type X BINARY INPUT Present_Value X Active=detection, or Inactive=no detection Polarity X rmal Polarity Object_Identifier X BINARY INPUT # Object_Name X "VFC Count Reset" Object_Type X BINARY INPUT Present_Value Yes X Active=reset requested, or Inactive=no reset requested Polarity X rmal Polarity Page 16 of 26

17 Object_Identifier X BINARY INPUT # Object_Name X "CO2 Auto Calibration" Object_Type X BINARY INPUT Present_Value X Active=auto calibration enabled, or Inactive=auto calibration disabled Polarity X rmal Polarity Object_Identifier X BINARY INPUT # Object_Name X "Ch.x Input Alarm" Object_Type X BINARY INPUT Present_Value X Active=input alarm, or Inactive=no input alarm Polarity X rmal Polarity Object_Identifier X BINARY INPUT # Object_Name X "Ch.x COV Status" Object_Type X BINARY INPUT Present_Value X Active=significant change, or Inactive=no significant change Page 17 of 26

18 Polarity X rmal Polarity Object_Identifier X BINARY INPUT # Object_Name X "Ch.x COV Status" Object_Type X BINARY INPUT Present_Value X Active=significant change, or Inactive=no significant change Polarity X rmal Polarity Binary Value Object Type Dynamically creatable using BACnet's CreateObject service? Dynamically deletable using BACnet's DeleteObject service? Object_Identifier X BINARY VALUE # Object_Name X "Low Battery" Object_Type X BINARY VALUE Present_Value X Active=Low Battery, or Inactive=Battery Okay Page 18 of 26

19 Polarity X rmal Polarity Object_Identifier X BINARY VALUE # Object_Name X "Online Status" Object_Type X BINARY VALUE Present_Value X Active=Online, or Inactive=Offline Polarity X rmal Polarity Object_Identifier X BINARY VALUE # Object_Name X "Sensor Fault" Object_Type X BINARY VALUE Present_Value X Active=Fault, or Inactive= Fault Polarity X rmal Polarity Object_Identifier X BINARY VALUE # Object_Name X "Temperature COV Status" Object_Type X BINARY VALUE Present_Value X Active=Significant Change, or Inactive= Significant Change Page 19 of 26

20 Polarity X rmal Polarity Object_Identifier X BINARY VALUE # Object_Name X "Humidity COV Status" Object_Type X BINARY VALUE Present_Value X Active=Significant Change, or Inactive= Significant Change Polarity X rmal Polarity Object_Identifier X BINARY VALUE # Object_Name X "CO2 COV Status" Object_Type X BINARY VALUE Present_Value X Active=Significant Change, or Inactive= Significant Change Polarity X rmal Polarity Page 20 of 26

21 Object_Identifier X BINARY VALUE # Object_Name X "Setpoint COV Status" Object_Type X BINARY VALUE Present_Value X Active=Significant Change, or Inactive= Significant Change Polarity X rmal Polarity Multi-State Input Object Type Dynamically creatable using BACnet's CreateObject service? Dynamically deletable using BACnet's DeleteObject service? Object_Identifier X MULTI-STATE INPUT # Object_Name X "Fan Speed Switch" Object_Type X MULTI-STATE INPUT Present_Value X 1="Off", 2="Low", 3="Medium", 4="High", 5="Auto" Number_Of_States X 5 State_Text X 1="Off", 2="Low", 3="Medium", 4="High", 5="Auto" Multi-State Value Object Type Dynamically creatable using BACnet's CreateObject service? Page 21 of 26

22 Dynamically deletable using BACnet's DeleteObject service? Object_Identifier X MULTI-STATE VALUE # Object_Name X "Battery Level" Object_Type X MULTI-STATE VALUE Present_Value X 1="Poor", 2="Okay", 3="Good" Number_Of_States X 5 State_Text X 1="Poor", 2="Okay", 3="Good" Object_Identifier X MULTI-STATE VALUE # Object_Name X "Parent Link Quality" Object_Type X MULTI-STATE VALUE Present_Value X 1="Marginal", 2="Okay", 3="Good" Number_Of_States X 5 State_Text X 1="Marginal", 2="Okay", 3="Good" Object_Identifier X MULTI-STATE VALUE # Object_Name X "Ch.x Input Type" Object_Type X MULTI-STATE VALUE Page 22 of 26

23 Present_Value X 1="Current", 2="Voltage", 3="Resistance", 4="VFC", 4="Error" Number_Of_States X 5 State_Text X 1="Current", 2="Voltage", 3="Resistance", 4="VFC", 4="Error" Octet-String Value Object Type Dynamically creatable using BACnet's CreateObject service? Dynamically deletable using BACnet's DeleteObject service? Object_Identifier X OCTETSTRING VALUE # Object_Name X MAC Address" Object_Type X OCTETSTRING VALUE Present_Value X 00158D AE Object_Identifier X OCTETSTRING VALUE # Object_Name X "Parent" Object_Type X OCTETSTRING VALUE Present_Value X 00158D00010A780C Page 23 of 26

24 Device Object Type Dynamically creatable using BACnet's CreateObject service? Dynamically deletable using BACnet's DeleteObject service? Object_Identifier Yes X DEVICE # Object_Name Yes X "SonNet-BACnet-Gateway" Object_Type X DEVICE System_Status X Operational Vendor_Name X "Sontay Limited" Vendor_Identifier X 662 Model_Name X "SBIP" Firmware_Revision X "0.9.1" Application_Software_ Version X "1.1.8" Location Yes X "Building 1" Description Yes X "SonNet devices" Protocol_Version X 1 Protocol_Revision X 12 Protocol_Services_ Supported X stack library filled Protocol_Object_Types_ Supported X stack library filled Object_List X stack library filled Max_APDU_Length_ Accepted X 1476 bytes Segmentation_Supported X ne APDU_Timeout X 3000ms Number_Of_APDU_Retries X 3 Page 24 of 26

25 Device_Address_Binding X {} Database_Revision X counter Data Link Layer Options X BACnet IP, (Annex J) BACnet IP, (Annex J), Foreign Device ISO , Ethernet (Clause 7) ANSI/ATA 878.1, 2.5 Mb. ARCNET (Clause 8) ANSI/ATA 878.1, RS-485 ARCNET (Clause 8), baud rate(s): MS/TP master (Clause 9), baud rate(s): 9600, 19200, 38400, 57600, 76800, MS/TP slave (Clause 9), baud rate(s): MS/TP (Clause 9), transceiver unit load and isolation 1/4 unit load, isolated Point-To-Point, EIA 232 (Clause 10), baud rate(s): Point-To-Point, modem, (Clause 10), baud rate(s): LonTalk, (Clause 11), medium: Other: Network Options Router, Clause 6 - List all routing configurations (e.g. ARCNET-Ethernet, Ethernet-MS/TP, etc.): Annex H.3, BACnet Tunnelling Router over UDP/IP BACnet/IP Broadcast Management Device (BBMD) BBMD supports registrations by Foreign Devices Segmentation Capability Window Size Segmented requests supported Segmented responses supported Device Address Binding Static device binding supported for MS/TP Slaves and other devices Page 25 of 26

26 Character Sets Supported X ANSI X3.4 / UTF-8 IBMÔ/MicrosoftÔ DBCS ISO ISO (UCS-2) ISO (ICS-4) JIS C 6226 Whilst every effort has been made to ensure the accuracy of this specification, Sontay cannot accept responsibility for damage, injury, loss or expense from errors or omissions. In the interest of technical improvement, this specification may be altered without notice. Page 26 of 26