|
|
- Meagan Allen
- 5 years ago
- Views:
Transcription
1 Page 1 of 6 Page 1 of 12 Yaesu FT-5100/FT-5200 MODS Rev B (14 Apr 1993) This is a collection of hardware and software mods for the Yaesu 5100/5200 pair. I have the 5100, so I can't verify these for the I have collected every mod seen on the net (ie. Usene the introduction of the 5100, so I think this list is fairly complete. I am interested in getting updates and corrections to this list, so please send me if you find something that needs upda (This includes typos, wrong or missing attributions, caveats, warnings about unmentioned side effects, serial numbers of radios that won't do some of these mods, etc.) Brian McMinn (brian.mcminn@amd.com) N5PSS Backlight Control: Effect: manual control of backlight 1) Hold down the MHZ key and turn radio on 2) Use tuning knob to adjust brightness 3) When FUNC is active, the tuning knob will adjust brightness again. 4) You can restore automatic control by repeating step 1. Notes: Manual is fuzzy on this feature. Attributed: Yaesu SOME OF THESE MODIFICATIONS MAY DAMAGE YOUR RADIO IF YOU PERFORM THEM IMPROPERLY. WHEN IN DOUBT, DO NOT PERFORM THE MODIFICATION. This advice is free, so remember that you get what you pay for. Page 2 of 12 Crossband Repeat (reported as working on 5100 and 5200): Effect: Enable crossband repeat 1) Dial up two frequencies you want to crosslink (be sure to pay attention to transmit offsets, if any) 2) Turn radio off. 3) Hold down the RPT key and turn radio on Result: The tone encode/decode flags and the -+ flags will be flashing and the radio will be in low power mode. When either band's squelch opens, the other band is moved into the primary frequency display and the transmitter keys. Audio link appears to be speaker to mike. Exit crossband repeat mode by repeating steps 2 and 3 above. Attributed: Yaesu Transmitter Timeout: Effect: automatically limit transmitter "on" time 1) Hold down the HIGH/LOW button and turn radio on 2) Use tuning knob to change the number in left VFO. This number is number of minutes for the timeout timer. The factory default appears to be 15 minutes. 3) Transmitter shuts off with "Err" displayed in VFO if the time limit is exceeded. Attributed: Bill Mayhew, N8WED, wtm@uhura.neoucom.edu Page 3 of 12 Crossband Audio Enhancement: Effect: unmuffle crossband audio Connect a 27K ohm resistor between the audio-in and auido-out
2 Page 2 of 6 leads on the data jack (inside the shell of a mini plug, that is). The mic element stays live while in xband operation. It is a good idea to remove the mic from the rig while cross banding if you need/want to eliminate ambient audio. Attributed: Bill Mayhew, N8WED, wtm@uhura.neoucom.edu The "P" Key on the microphone: I was curious about that "P" key on my FT-5100, so I called Yeasu and they explained the situation. They designed the the mic to accomidate "future products". The "P" key is there to be taken advantage of at a later date by other models. They just did not want to re-design the mic again within a short period of time. Attributed: Will Collier, KB5WRK, COLLIER@gallant.apple.com Page 4 of 12 Expanded Receive: Page 5 of 12 Good Effect: enable extended receive coverage New range: MHz and MHz Bad Effect: disable automatic repeater shift selection. Warning: This mod does not apply to the FT-5200 as the design is somewhat different. Warning: You must have a very steady hand or else! A magnifying glass would help too. 1) Disconnect DC Power cable from radio. ALWAYS! **Caution** NEVER TRY TO TAKE APART (DISASSEMLBLE) THE FRONT CONTROL HEAD. It will void your warranty. 2) Remove (6) screws from Top Cover of Radio and (6) screws from Bottom Cover of radio. 3) Remove Top & Bottom Covers from Radio (Be careful of speaker falling out). 4) Remove the (2) silver screws on each side of the radio holding front control head to main body of radio. 5) Carefully pull away (a few inches) the Control Head from the radio body. CAREFUL with the Ribbon Cables. **NOTE** There are no numbers on the circuit board so you will have to match up with the diagram below. 6) On the rear of the Control head locate, Unsolder and remove jumper Pad R ) Solder across jumper pads: R4070 R4068 & R4064 (use wire or 0 Ohm resistor) **NOTE** If you want to change the D/MR button on the microphone to do Band Switching, now is the time. See the next mod. Expanded Receive continued: 8) Install Front Control head, Speaker, Top and Bottom Covers and Reconnect Power to the Radio. 9) Press and hold [D/MR] [F/W] [REV] Keys and turn on the Radio. Radio will now show & on Display. 10) Set UHF Rx Low - Press [MHz] and dial , press [D/MR] 11) Set UHF Rx High- Press [MHz] and dial , press [D/MR] 12) Set UHF Tx Low - Press [MHz] and dial , press [D/MR] 13) Set UHF Tx High- Press [MHz] and dial , press [D/MR]
3 Page 3 of 6 14) Set VHF Rx Low - Press [MHz] and dial , press [D/MR] 15) Set VHF Rx High- Press [MHz] and dial , press [D/MR] 16) Set VHF Tx Low - Press [MHz] and dial , press [D/MR] 17) Set VHF Tx High- Press [MHz] and dial , press [D/MR] 18) Set UHF offset - Press [F/W] then [RPT] dial press [RPT] 19) Set UHF tuning - Press [F/W] then [REV] dial 25.0 press [RPT] 20) Set VHF offset - Press [F/W] then [RPT] dial press [RPT] 19) Set VHF tuning - Press [F/W] then [REV] dial 20.0 press [RPT] (VHF tuning step varies by state -- many use 15.0) Diagram: [there are no tabs in this section - ed] Ok, here's where it gets tricky, but so you know, a ' ' represents a jumper.!ribbon!!ribbon!!cable!!cable!!j4002!!j4001!!!!!!!! Rear view of FT-5100!! Control Head.!!!!!!!!!!!! R R R R R R R R R R R R R R R R!! !! !! !! !!! Page 6 of 12 Expanded Receive continued: Stock US Jumpers After Mod. Jumpers R4001 R4001 R4003 R4003 R4004 R4004 R4051 R4051 R4061 R4061 R4062 R4062 R4064 R4067 <- for D/MR button mod R4068 R4070 R4072 This mod is on Delphi as FT5100.MOD and on anomaly.sbs.com. Attributed: Tony Pelliccio, KD1NR system@garlic.sbs.com Band Switching via D/MR button on microphone: Effect: D/MR button on microphone performs band switching rather than D/MR function. 1-5) as in above mod 6) Remove the jumper on Pad R4067 7) skip above step 7 8) continue with step 8 above Attributed: Tony Pelliccio, KD1NR system@garlic.sbs.com Page 7 of 12 Band Switching or Tone Burst via D/MR button on microphone (5200): Effect: change function of D/MR button on mike. This is based on information from Yaesu in Japan. The functions of pin 5 (the microphone button) can be altered by changing jumpers in the control head. To find these jumpers, see the section on packet radio in the ordinary instruction book. Pin 5 Function D/MR Control Head Jumper No Closed Jumper Marked By
4 Page 4 of 6 Band 1750Hz Tone Burst Main band Busy Out Sub band Busy Out Call Channel Main / Sub band busy out - When open SQL = 5 Volt DC Closed SQL = 0 Volt DC [ed - I'm not sure what this means since I don't own a 5200] Attributed: John Newgas, G7LTQ jnewgas@cix.compulink.co.uk, Page 8 of 12 Mute Level (5200): Effect: [ed - I'm not really sure] See above for location of jumpers, etc. Mute Level Selection No Mute Minimum Middle Maximum Attributed: John Newgas, G7LTQ jnewgas@cix.compulink.co.uk Crossband Repeat (5200): Effect: crossband repeater Bad effect: CTCSS function is lost [ed -- there is another crossband mod in this list...] This is based on information from Yaesu in Japan. These jumpers are located in the main radio case. For location, refer to the FT5200 Technical Guide. 1) Remove (open) JP5017 on the interface unit 2) Press and hold PRI button while switching on the power. 3) The FT5200 will now work as a cross band repeater. 4) The CTCSS function will be lost. Attributed: John Newgas, G7LTQ jnewgas@cix.compulink.co.uk Page 9 of 12 Extended Frequency Range (5200): Effect: set receive and transmit range. Bad effect: ARS gone. This is based on information from Yaesu in Japan. These jumpers are located in the main radio case. For location, refer to the FT5200 Technical Guide. 1) Close (short) JP5001, JP5002, JP5003, JP5006 and JP5007 2) Remove (open) JP5004 and JP5005 The frequency range possible will now be approximately : VHF Rx MHz Tx MHz UHF Rx MHz Tx Mhz The radio's alignment was done at the factory for your original frequency bands and so there will not be optimum behavior outside these ranges. Broadening the alignment will sacrifice performance at usual frequencies. In practice, the
5 Page 5 of 6 alignment does not need adjustment. You can program the frequency limits now. [ed - note the similarity (and dissimilarity!) to the 5100's program-limit sequence above] 3) Press and hold [D/MR] [F/W] [REV] keys and turn radio on. 4) Program in VHF low edge of Rx VHF high edge of Rx VHF low edge of Tx VHF high edge of Tx 5) Repeat for UHF in the same order. I [John] have not done this so I can give no further advice on programming. Attributed: John Newgas, G7LTQ jnewgas@cix.compulink.co.uk Page 10 of 12 Extended Frequency Range (5200): [ed - yes, there are two mods and I include them both since they are so different in style (and perhaps content).] Effect: set receive and transmit range. Bad effect: ARS gone. The following explains how to expand the receive and transmit frequency range of the Yaesu FT-5200 and how to enable the crossband repeater operation. All the modifications are carried out on the interface board and involve removing or adding links on jumper spots. You will get considerably increased receive and transmit coverage; however, you will lose the Automatic Repeater Shift (ARS) feature. You may think this is an acceptable price. Finally, it should be obvious, but during this procedure you will obviously lose any stored memories. 1) Remove the control head and set on one side 2) Remove the upper and lower covers on the main chassis. For convenience, remove the speaker, noting which way the two pin pcb connector is oriented. [ed -- does it matter?] 3) Remove two side screws holding on the front of the chassis and remove chassis front. (The chassis front is the surface with the contacts for the control head.) 4) Locate a double row of ten by two jumper spots, numbered 1 to 20. The jumper configurations will depend on the area for which the rig was intended. Note the arrangement if you ever want to un-modify your radio. 5) Using a fine-tip soldering iron, set the jumper spots as follows: Page 11 of 12 Extended Frequency Range (5200) continued: 1 closed 2 closed 3 closed 4 open 5 closed 6 closed 7 closed 6) This completes the alteration for frequency expansion. Reassemble the radio. 7) Reinitialise the radio by simultaneously holding D/MR, F/W, REV and POWER. You must now program in the band limits. The display will show a blinking "1" in the left-hand memory box and " " in the left-hand frequency display. (Ignore the right-hand display for now). The following limits are suggested, but the RF circuitry of the rig will only cover slightly less. Use the dial or up/down buttons to select the frequency and then press D/MR to store it. The blinking "1" will increment. VHF rx: VHF tx: (display will show blinking "1" and " ")
6 Page 6 of 6 UHF rx: UHF tx: (Note: it is possible to set the R limits wider than the T limits; for obvious reasons you cannot have the reverse situation). 8) You can repeat step 7 above at any time if you need to change the limits. Page 12 of 12 Extended Frequency Range (5200): 9) The pre-set repeater offsets are now no longer available and you will have to set them up manually using the instructions on page 16 of the manual. The Automatic Repeater Shift (ARS) feature (also on page 16 of the manual) will also have disappeared and you will have no way of getting it back (except by changing the jumpers back). To enable the crossband repeat, remove the link at jumper spot 17. (Note, just below jumper spot 17 is a separate jumper spot, not part of the group of twenty - leave this alone). Attributed: Hugo Cornwall Cross Band Repeater (5200) Effect: enable crossband repeat [ed - this is a continuation of the above] 1) You can enable the crossband repeater without altering the frequency coverage. The only hardware alteration is the removal of link 17. 2) To enable, turn on rig while holding down [RPT] button. The rig is now a crossband repeater - you will get confirmation of this from the display: the 100s position on the two frequency displays will be replaced by a "R". 3) While in cross-band repeater mode you can change the frequencies of each band. 4) The crossband repeater suffers from desense. It works better at low power and even better if you use an external diplexer and separate antennas. The more isolation between the two bands, the better. As with all cross-band repeaters, results will be poor if the UHF frequency is a direct multiple of the VHF frequency. If you are planning extended use of a crossband repeater, make extra sure that the rig is adequately ventilated.
Connecting the FCC-2 to the Hendricks DC Kits Bob Okas, W3CD
Connecting the FCC-2 to the Hendricks DC Kits Bob Okas, W3CD This is an application note that describes how you can connect the NorCal FCC-1/2 combination to the DC kits. It involves a few extra components
More informationMicrophone audio, from the MFJ-1278B to your transmitter. Ground, audio and PTT common. Push-to-talk, to allow the MFJ-1278B to key your transmitter.
Computer interfacing, covered in the previous chapter, is only half the interfacing task. The other half is connecting your MFJ-1278B to your radios. MFJ-1278B Radio Ports Interfacing the MFJ-1278B to
More informationCross-Connect Interface
Cross-Connect Interface User Manual Document #: 050-015-0036R01 November 2006 TASC Systems Inc. Langley, BC Canada Cross-Connect System User Manual Preface This document describes the installation, commissioning
More informationTX4400 UHF CB RADIO INSTRUCTION MANUAL TX4400 INSTRUCTION MANUAL PAGE 1
TX4400 UHF CB RADIO INSTRUCTION MANUAL TX4400 INSTRUCTION MANUAL PAGE 1 TABLE OF CONTENTS GENERAL................................... 3 FEATURES.................................. 3 BASIC OPERATION...4 Front
More information5 With the transceiver off, press and hold the [F] and [V/M] keys; while holding them in, turn the radio on. Modification is now complete.
FT-897 mods View PDF mods file 1 Remove the 8 screws affixing the top panel of the transceiver and gently lift it off. 2 Carefully remove the small 2-pin speaker plug from the left rear corner of the transceiver
More informationFCC ID: AXI IC: 10239A Alignment
Introduction The VX-261 is carefully aligned at the factory for the specified performance across the frequency range specified for each version. Realignment should therefore not be necessary except in
More informationRMV25 / RMV50 RMU25 / RMU45
RMV25 / RMV50 RMU25 / RMU45 Owner's Manual TABLE OF CONTENTS INTRODUCTION... 3 FCC Requirements... 3 SAFETY WARNING INFORMATION... 3 CONTROLS and INDICATORS... 5 FRONT PANEL... 5 LCD Icons and Indicators...
More informationPC Tune PC Tune Test Procedures for 5100 Series Portable Radios
PC Tune PC Tune Test Procedures for 5100 Series Portable Radios Part Number 002-9998-6513014 August 2008 Copyright 2006, 2007, 2008 by EFJohnson Technologies The EFJohnson Technologies logo, PC Configure,
More informationSome info for FT90. Serial Numbers
Some info for FT90 Serial Numbers For all Yaesu/Vertex radios that I've seen, the serial numbers are in the format of YPXXXXXX where "Y" is the production year, "P" is the production run and "XXXXXX" is
More informationRITEK RIT for Collins KWM-2/2A 10/01/2002
RITEK RIT for Collins KWM-2/2A 10/01/2002 The RITEK RIT (receiver incremental tuning) control was developed for KWM-2/2A in 1992 to "clarify" received signals differing from the transmit frequency indicated
More informationICS REPEATER CONTROLLERS
ICS REPEATER CONTROLLERS BASIC CONTROLLER USER MANUAL INTEGRATED CONTROL SYSTEMS 1076 North Juniper St. Coquille, OR 97423 Email support@ics-ctrl.com Website www.ics-ctrl.com Last updated 5/07/15 Basic
More informationLBI-38808B. Maintenance Manual EDACS UTILITY PROGRAMMING
LBI-38808B Maintenance Manual EDACS UTILITY PROGRAMMING NOTICE! Repairs to this equipment should be made only by an authorized service technician or facility designated by the supplier. Any repairs, alterations
More informationRPS-9000 Programming Software for the TYT TH-9000
for the TYT TH-9000 Memory Types Memories Limit Memories VFO Channels Receive Frequency Transmit Frequency Offset Frequency Offset Direction Channel Spacing Name Tone Mode CTCSS Rx CTCSS DCS Rx DCS Memory
More informationW4RT Electronics A Division of CyberAir Development Corporation 22 March For the Yaesu FT-817 & FT-817ND
W4RT Electronics A Division of CyberAir Development Corporation www.w4rt.com 22 March 2005 For the Yaesu FT-817 & FT-817ND The ONE BOARD FILTER (OBF-817) is an accessory for the YAESU FT-817 and FT-817ND.
More informationG1MFG.com. Home of the cheapest ATV transmitters and receivers in Europe! Please read all of this document before attempting to use your controller.
G1MFG.com Home of the cheapest ATV transmitters and receivers in Europe! 23/24cm LCD controller technical information V3 software Please read all of this document before attempting to use your controller.
More informationCrossband Repeaters (CBR) OCCA Meeting April 10, 2017
OCCA Meeting April 10, 2017 What do we mean by a Cross-Band Repeater or CBR? Crossband (cross-band, cross band) operation is a method of communication in which a radio station (mobile) receives a signal
More informationLogiTALKER OWNER S MANUAL. Voice Keyer. Idiom Press. PO Box 1015, Merlin, OR USA
LogiTALKER Voice Keyer OWNER S MANUAL Idiom Press www.idiompress.com PO Box 0, Merlin, OR -0 USA + -- Preface Thank you for purchasing our LogiTALKER, a stand-alone voice keyer for your radio. To put the
More informationFrequency Coverage MHz RF Power Output 30W SSB / 9W AM/ 30W FM Dual Finals on Heat Sink Modes AM, FM, USB, LSB Microprocessor
MAGNUM M-257 30W AM/ /FM/SSB 10--11 Meterr Mobile Trranscei ivverr n Prri iiccee: : US$ 250..00 eexx ssttoocckk JJaakkaarrttaa (Arrrri ( iivvi iinngg 2 d weeeekk iinn i Maarrcchh) ) SPECIFICATIONS Frequency
More informationSR3400 Base Station Module Configuration and Use Series-2 Cards Only
SR3400 Base Station Module Configuration and Use Series-2 Cards Only A.W. Communication Systems Ltd Crook Barn, The Crook Rowel Town, Carlisle Cumbria Telephone (44) 1697-748777 Fax (44) 1697-748778 www.toneremote.com
More informationmat-30 HF-SSB Automatic Antenna Tuner Instruction Manual Version V1.0
INTRODUCTION mat-30 HF-SSB Automatic Antenna Tuner Instruction Manual Version V1.0 The mat-30 is an automatic tuner intended for use with modern Yaesu transceivers. It works with some Yaesu transceiver
More informationATP-5189 Programming Software for the Anytone AT-5189
for the Anytone AT-5189 Memory Types Memories Limit Memories VFO Receive Frequency Transmit Frequency Offset Frequency Offset Direction Channel Spacing Name Tone Mode CTCSS Rx CTCSS DCS Memory Channel
More informationLBI-31807D. Mobile Communications MASTR II REPEATER CONTROL PANEL 19B234871P1. Maintenance Manual. Printed in U.S.A.
D Mobile Communications MASTR II REPEATER CONTROL PANEL 19B234871P1 Maintenance Manual Printed in U.S.A. This page intentionally left blank 13 PARTS LIST 12 PARTS LIST LBI-31807 11 PARTS LIST 10 SCHEMATIC
More informationPacific Antenna Simple Keyer Kit
Pacific Antenna Simple Keyer Kit Specifications and Features: Speed range of 5 to 30 wpm Operates in either iambic A or B mode, with B being the default 2 message memories Tune and Beacon modes Built on
More informationDC-1122 Compact 5W UHF CB Radio
DC-1122 Compact 5W UHF CB Radio Instruction Manual Introduction! NOTE Use of the citizen band radio service is licensed in Australia by ACMA Radio communications (Citizen Band Radio Stations) Class Licence
More informationJEM Radio II Operation Guide. Manual P/N M Victor Place Colorado Springs, Colorado
JEM Radio II Manual P/N M09999-999 2115 Victor Place Colorado Springs, Colorado 80915 800.284.0399 www.jemcom.com Table of Contents Display... 3 Channel Entry... 4 Shortcuts... 4 Text Messages... 4 Buttons...
More informationOPERATING GUIDE VHF TRANSCEIVER. Iç-G88
OPERATING GUIDE VHF TRANSCEIVER Iç-G88 INTRODUCTION PREFACE We appreciate you choosing Icom for your communication needs. The MDC 1200 signaling system is built into your IC-G88 vhf transceiver. IMPORTANT
More informationProgramming Alinco -135T, 235T, and 435T VHF/UHF Radios. RADIO DISPLAYS and CONTROLS: The front panel of the radio is shown in Figure 1.
06/01/2011 Programming Alinco -135T, 235T, and 435T VHF/UHF Radios RADIO DISPLAYS and CONTROLS: The front panel of the radio is shown in Figure 1. Figure 1 Turning The Radio On: The power switch [1] is
More informationGoals: Board ID's in System Transmitter components/modules TLD5321A exciter board
Micor Unified Chassis Base Station Conversion to A Ham Band Repeater by Lawrence Glaister VE7IT November 2002 Goals: -To duplex a base station radio set for repeater usage. - To mount and tune a micor
More informationLDG TW-1 Talking Wattmeter
LDG TW-1 Talking Wattmeter LDG Electronics 1445 Parran Road, PO Box 48 St. Leonard MD 20685-2903 USA Phone: 410-586-2177 Fax: 410-586-8475 ldg@ldgelectronics.com www.ldgelectronics.com 1 LDG TW-1 Talking
More informationCat. No OWNER S MANUAL. HTX-212 Two-Meter Mobile Transceiver. Please read before using this transceiver.
19-1125.fm Page 1 Tuesday, August 3, 1999 9:47 AM Cat. No. 19-1125 OWNER S MANUAL HTX-212 Two-Meter Mobile Transceiver Please read before using this transceiver. 19-1125.fm Page 2 Tuesday, August 3, 1999
More informationYou must activate your warranty Do not call to register your radio.
INTRODUCTION Congratulations on your purchase of a Stryker 10 meter mobile amateur transceiver. Your Stryker is designed to provide years of enjoyment and trouble-free service.there are many features and
More informationTECHNICAL INFORMATION BULLETIN
TECHNICAL INFORMATION BULLETIN T/B No.: TIBFM 15-02 Rev A Revision date: JUNE24/08 Issue Date: JUNE18/08 TiL Model: TDFM-600/6000/7000 transceivers with Type I or Type II modules. TiL P/N: 011210-1,-2,-3,-4,-5
More informationTK-931 Receiver Modifications
TK-931 Receiver Modifications This page identifies all the hardware modifications necessary to adapt a Kenwood TK-931 transceiver for 902 MHz repeater receive operation. Not shown here is the effort required
More informationOWNER S MANUAL FRS RADIO
OWNER S MANUAL FRS RADIO 21-1860 INTRODUCTION Your RadioShack FRS radio is a portable, easy-to-use, two-way radio that you can carry almost anywhere. Use it at shopping malls, amusement parks, sports events,
More informationCAT-700B Repeater Controller Computer Automation Technology, Inc
CAT-00B Repeater Controller Computer Automation Technology, Inc N.W. st Avenue, Suite Fort Lauderdale, Florida 0 Phone: () 8- Fax: () 88-8 Internet: http://www.catauto.com Table of Contents Chapter Page.
More informationB & D Enterprises 1P repeater controller pg 1 INTRODUCTION:
B & D Enterprises 1P repeater controller pg 1 INTRODUCTION: The 1P is a basic repeater controller. The controller uses low power devices and stores all commands and system status in non-volatile EE prom.
More informationAT-5888UV Programming Software for the AnyTone AT-5888UV
AT-5888UV Programming Software for the AnyTone AT-5888UV Memory Channel Functions Memory Types Memories Limit Memories Hyper Memory 1 Hyper Memory 2 Receive Frequency Transmit Frequency Offset Frequency
More informationDEC-001 Installation Instructions
DEC-001 Installation Instructions Skill Level: The installation of this assembly requires a medium level of expertise in working with modern electronic equipment. The use of appropriate tools, correct
More informationSUBELEMENT T4. Amateur radio practices and station set up. 2 Exam Questions - 2 Groups
SUBELEMENT T4 Amateur radio practices and station set up 2 Exam Questions - 2 Groups 1 T4A Station setup: connecting microphones; reducing unwanted emissions; power source; connecting a computer; RF grounding;
More informationReference for UV-5R Menus by Jim Unroe - KC9HI 2-April-2014
Long Name / Description / / Notes / 0 SQL Carrier Squelch Mutes the speaker of the transceiver in the absence of a strong signal. VHF squelch is either OFF or ON. UHF squelch is either OFF or one of 9
More informationCCR24T CCR24R. User s Guide WIRELESS TRANSMITTER SYSTEM WARRANTY SERVICE CARD WARRANTY CARD
WARRANTY SERVICE CARD WARRANTY CARD PRODUCT NAME Wireless Transceiver System PERIOD MODEL NAME CCR24GEN YEAR PURCHASE DATE.. 200_ From the date of WARRANTY PERIOD.. 200_ purchase. CUSTOMER S ADDRESS :
More informationKenwood TH-F6. Conversion modifications YES, IT CAN BE DONE!
Kenwood TH-F6 Conversion modifications YES, IT CAN BE DONE! TH F6 and TH F7 is, actually, the same transceiver. Well, there is a difference: one diode. Warning: This modification will reset your radio
More informationPacific Antenna Easy TR Switch
Pacific Antenna Easy TR Switch Kit Description The Easy TR Switch is an RF sensing circuit with a double pole double throw relay that can be used to automatically switch an antenna between a separate receiver
More informationHF SIGNALS ΜBITX. The QRP HF General Coverage Transceiver you can build. Buy Now Circuit Description Wireup Tune Up Help and Support BITX Hacks
Page 1 of 5 HF SIGNALS ΜBITX The QRP HF General Coverage Transceiver you can build Buy Now Circuit Description Wireup Tune Up Help and Support BITX Hacks ($109 USD) Page 2 of 5 The µbitx is a general coverage
More informationDownloaded from
Owner s Manual AM/FM 40 CHANNEL & TONE SQUELCH CITIZENS BAND TRANSCEIVER Downloaded from www.cbradio.nl Characteristics of C-Five 1. Improved audio sensitivity by adopting audio compressing and decompressing
More informationYaesu FT-8800R Alignment
DUAL BAND FM TRANSCEIVER Introduction and Precautions The FT-8800R has been carefully aligned at the factory for the specified performance across the 144 MHz and 430 MHz amateur bands. Realignment should
More informationMABEL, PiTone and Allstar for the Yaesu Fusion DR-1X Repeater
MABEL, PiTone and Allstar for the Yaesu Fusion DR-1X Repeater MABEL is a program designed to run on a Raspberry Pi 3 (rpi) in conjunction with Allstar/app-rpt controlling a Yaesu Fusion DR-1X repeater.
More informationCHIPSWITCH DOC S RADIO REPAIR OWNERS MANUAL. HR2510 / HR2600 / LINCOLN 10 Meter Amateur Transceiver.
DOC S RADIO REPAIR HR2510 / HR2600 / LINCOLN 10 Meter Amateur Transceiver CHIPSWITCH OWNERS MANUAL Revised August 28th, 2000 http://hr2510.freeservers.com/ - 1 - Table of Contents FIRST TIME INSTALL /
More informationICS REPEATER CONTROLLERS
ICS REPEATER CONTROLLERS SINGLE M USER MANUAL INTEGRATED CONTROL SYSTEMS 1613 Bonnie Avenue Dixon, IL 61021 Voice 815-284-6963 Fax 815-288-0718 Website www.ics-ctrl.com Last updated 01/08/2005 Single M
More informationAUDIO MODE SELECTOR MODEL AMS-6000
AUDIO MODE SELECTOR MODEL AMS-6000 Installation and Operating Instructions Til Document No. 03RE325 Rev. n/c Issue 4 August 2007 Technisonic Industries Limited 240 Traders Boulevard, Mississauga, Ontario
More informationRadio Control Installation and Operating Instructions System 4
Radio Control Installation and Operating Instructions System 4 P.O. Box 403, One Cedar Parkway, Jackson, WI 53037 Phone: 800-628-1909 Fax: 262-677-2058 Revision: April 19, 2012 Contents Introduction 3
More informationCustom Integrated Circuit (MSM9520RS) Replacement Module
FT-101Z/ FT-107/ FT-707/ FT-901,902 (later version) DISPLAY COUNTER UNIT (PB-2086A) Custom Integrated Circuit (MSM9520RS) Replacement Module Assembly and Installation Manual (v1.3e) STEP-BY-STEP PROCEDURES
More informationImportant safety instructions
RCR-29 GB Version 1 Important safety instructions VERY IMPORTANT PLEASE READ Sangean suggest that you keep your AC Adapter at least 12 inches away from the radio while listening to the AM Band. Your Sangean
More informationHT-1A Dual Band CW QRP Transceiver. Kit Building Instructions
HT-A Dual Band CW QRP Transceiver Kit Building Instructions Rev B, July 8, 08 Designed by BD4RG Exclusively distributed by CRKITS.COM and its worldwide distributors Join the group http://groups.io/g/crkits
More informationCross-band Repeating
Cross-band Repeating Santa Clara County ARES /RACES Last Updated September 11, 2018 ARES and Amateur Radio Emergency Service are registered service marks of the American Radio Relay League Incorporated
More informationKenwood TM-D710A mobile ham radio HARBOR instructions 1
Kenwood TM-D710A mobile ham radio HARBOR instructions 1 Special Note: The radio in the larger black-yellow case must be set to Narrow FM (NFM) to be able to receive from the other radios. See the special
More informationMFJ ENTERPRISES, INC.
Radio Interface Model MFJ-5124K/Y INSTRUCTION MANUAL CAUTION: Read All Instructions Before Operating Equipment! MFJ ENTERPRISES, INC. 300 Industrial Park Road Starkville, MS 39759 USA Tel: 662-323-5869
More informationCW-ADD. Universal CW Adapter for SSB Transceivers. Assembly manual. Last updated: October 1,
CW-ADD Universal CW Adapter for SSB Transceivers Assembly manual Last updated: October 1, 2017 ea3gcy@gmail.com Updates and news at: www.ea3gcy.com Thanks for building the Universal CW Adapter kit CW-ADD
More informationInstallation... 3 Installing The Radio... 3 Ignition Noise Interference... 4 Antenna... 4 External Speaker... 4 Public Address...
TABLE OF CONTENTS CHAPTER 1 Specifications.............................................. 2 PAGE BIG RIG SERIES S 1 MOD PW R 20 0 3 SW R 40 1 5 5 60 1.5 7 10 2 9 20 80 3 30 +20 40 50 +40 100% MAX db +60
More informationSigtronics Auto Squelch Intercom System Installation and Operating Instructions Models SAS-440 and SAS-640
Sigtronics Auto Squelch Intercom System Installation and Operating Instructions Models SAS-440 and SAS-640 INTRODUCTION ATTENTION INSTALLER: To assure a trouble free installation, please read the entire
More informationOWNER S MANUAL
OWNER S MANUAL 19-1208 RADIOSHACK CORP. FCC ID : AAO1901208 JOB # : 578ZA1 EXHIBIT # : 6 INTRODUCTION Your Radio Shack 19-1208 Business band transceiver is a portable, easy-to-use, two-way radio that you
More informationVHF Transceiver AR6201
VHF Transceiver AR6201 Operating Instructions Issue 2 / October 2010 Article No. 0618.764-071 Becker Flugfunkwerk GmbH Baden-Airpark B 108 77836 Rheinmünster Germany Telefon / Telephone +49 (0) 7229 /
More informationMastr III P25 Base Station Transmitter Tune-up Procedure
Mastr III P25 Base Station Transmitter Tune-up Procedure 1. Overview The Mastr III Base Station transmitter alignment is performed in several steps. First, the Transmit Synthesizer module is aligned to
More informationEasy-Link Plus Version 2.2
Easy-Link Plus Easy-Link Plus Version 2.2 Copyright 1994-2000 IDA Corporation All Rights Reserved This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
More informationA Covert Tracking System Using the DDF5931
1.0 Introduction A Covert Tracking System Using the DDF5931 A Technical Application Note from Doppler Systems April 25, 2004 This application note describes a simple covert tracking system using the Doppler
More informationPacific Antenna - Easy TR Switch
Pacific Antenna - Easy TR Switch Kit Description The Easy TR Switch is an RF sensing switch that can be used to switch an antenna between a receiver and transmitter. It also has a second switched pair
More informationFT-897 Alignment. Local Oscillator Adjustment. PLL Adjustment
FT-897 Local Oscillator Adjustment Reference Frequency Adjustment a. Connect a frequency counter to TP1032. b. Adjust the trimmer capacitor (TC5001) for 67.875000MHz ±5Hz on the frequency counter. c. Connect
More informationeguard EG2233, EG3333, EG3355, EG3388 & EG8406: Installation and Set-up Procedures Tx 2200 and Rx 4200 Boards
eguard EG2233, EG3333, EG3355, EG3388 & EG8406: Installation and Set-up Procedures Tx 2200 and Rx 4200 Boards A. Primary Technical Data: Transmitter Operating voltage DC 24V Operating current. < 450mA
More informationVX-2100/VX-2200 (UHF) Alignment
VX-2100/VX-2200 (UHF) Introduction The VX-2100/2200 is carefully aligned at the factory for the specified performance across the frequency range specified for each version. Realignment should therefore
More informationATP-588 Programming Software for the Anytone AT-588
for the Anytone AT-588 Memory Channel Functions Memory Types Memories Limit Memories VFO Receive Frequency Transmit Frequency Offset Frequency Offset Direction Channel Spacing Name Tone Mode CTCSS Rx CTCSS
More informationCAT-700 Repeater Controller
CAT-700 Repeater Controller Computer Automation Technology, Inc. 4631 N.W. 31st Avenue, Suite 142 Fort Lauderdale, Florida 33309 Phone: (954) 978-6171 Fax: (561) 488-2894 Internet: http://www.catauto.com
More informationGreaval GV-8S. User Manual
Greaval GV-8S User Manual Version 2017 A B C D E F G LED Indicator Lights red during transmit, green when receiving a signal Channel Switch Rotate to select a channel. No. 16 is the scanning channel Power
More informationBeeLine TX User s Guide V1.1c 4/25/2005
BeeLine TX User s Guide V1.1c 4/25/2005 1 Important Battery Information The BeeLine Transmitter is designed to operate off of a single cell lithium polymer battery. Other battery sources may be used, but
More informationEDACS WALL MOUNT STATION. Maintenance Manual. Mobile Communications LBI-31838A TABLE OF CONTENTS
A Mobile Communications EDACS WALL MOUNT STATION TABLE OF CONTENTS SYSTEM BOARD & REGULATOR BOARD.......... LBI-31892 KEY/DISPLAY BOARD MAINTENANCE MANUAL.... LBI-31940 Maintenance Manual Printed in U.S.A.
More informationALWAYS ATTACH THE SAFETY ROPE TO A STABLE SUPPORT BEFORE ATTEMPTING TO ATTACH THE UNIVERSAL MOUNT TO A WINDOW FRAME OR RAIL.
MFJ-1623 Introduction The MFJ-1623 was designed to provide portable or permanent HF communications on 30 through 10 meters and VHF on 6 meters. The universal mount design allows the user to install the
More informationImportant safety instructions
MMR-88 Version 1 Important safety instructions 1. 2. 3. 4. 5. 6. 7. 8. 9. Please read these instructions carefully. Please keep these instructions for future reference. Heed all warnings Follow all instructions
More informationCross-banding. Crossband Repeating
Crossband Repeating Crossband Repeating is a process where a Ham transmits one signal on one band (typically UHF), and it is received by another radio with a better antenna/power installation, and re-transmitted
More informationTECHNICAL NOTES MT-4 Radio Systems TN182 Battery Level Reporting and Remote P25 Test Tone
Battery Level Reporting is a method of activating a repeater remotely to have it transmit a signal that reports the battery voltage level over RF. The Remote P25 Test Tone is a remotely activated Standard
More informationINSTRUCTION MANUAL TX3200 UHF TRANSCEIVER STANDARD COMMUNICATIONS PTY. LTD.
INSTRUCTION MANUAL TX3200 UHF TRANSCEIVER STANDARD COMMUNICATIONS PTY. LTD. CONTENTS Contents................................... 2 Introduction................................ 2 Features....................................
More informationVHF Transceiver AR6201-(X0X) Software Versions: SCI1050S305 Version 3.05 SCI1051S305 Version 1.49 and upwards
VHF Transceiver AR6201-(X0X) Software Versions: SCI1050S305 Version 3.05 SCI1051S305 Version 1.49 and upwards Operating Instructions Issue 5 / November 2013 Article No. 0618.764-071 Becker Avionics GmbH
More informationMZ2 HEADPHONE AMPLIFIER, PREAMP, & STEREO AMPLIFIER USER GUIDE
MZ2 HEADPHONE AMPLIFIER, PREAMP, & STEREO AMPLIFIER USER GUIDE Linear Tube Audio Takoma Park, MD, USA WARNING: For safety, the cover of this amplifier should be secured at all times. DC voltages as high
More informationDX AM FM SSB CW PA Amateur Base Station Transceiver OWNER S MANUAL RX / TX 2 4 POWER NF CHANNEL MODE RF POWER OFF CAL OFF OFF CALIBRATE
1 2 3 6 4050 ULA 6070 TI 80 90 100 9 DX 2517 2517 RX / TX 0 2 4 SWR WATTS SET 81012 22 1 010 3 2030 5 MOD 7 ON dbover 9 SIGNAL +20 +40+60 PA FM AM USB LSB CW POWER ON SWR NB / ANL R.BEEP +10KHz NF CHANNEL
More informationUV-5R Manual. pofung UV-5R
pofung UV-5R Pre conditions 1 Charge Battery 2 Attach antenna 3 Take Note of: , , , , 4 Orange VFO/MR, BlueA/B, Black BAND, 5 10 Key Number Pad. Used to enter key numbers
More informationHF-SSB MICOM - LINK - FDN6123 HF-SSB MICOM - LINK
American Communication Systems Discover the Power of Communications TO ORDER VISIT http://www.ameradio.com HF-SSB MICOM - LINK - FDN6123 HF-SSB MICOM - LINK Instruction Manual 6886857J01 Table of Contents
More informationWIRES-X Portable Digital Node Function. Instruction Manual
Wide-Coverage Internet Repeater Enhancement System WIRES-X Portable Digital Node Function Instruction Manual Please read this Instruction Manual carefully for appropriate procedure. Preparation Procedure
More informationConverting the Motorola 42 to 50 MHz MT1000 or P200 to 50 to 54 MHz
Converting the Motorola 42 to 50 MHz MT1000 or P200 to 50 to 54 MHz Hardware mods by WB8VLC. RSS mods by WA1MIK Transmitter and receiver mods to tune the entire band and direct RSS frequency entry. Revision
More informationSEARCH LITE OPERATION MANUAL
SEARCH LITE OPERATION MANUAL Corporate Profile Trilithic, Inc. was founded in 1986 as an engineering and assembly company providing customized communications and routing systems for business and government
More informationALAN 777 PMR 446 Radio Set User manual
ALAN 777 PMR 446 Radio Set User manual The all new ALAN 777 represents the very latest and most advanced technology currently available on the PMR446 and LPD market. With its stylish lines and modern design,
More informationINSTRUCTION MANUAL VHF FM TRANSCEIVER TK-6110 B (K,K2)
INSTRUCTION MANUAL VHF FM TRANSCEIVER TK-6110 B62-1216-20 (K,K2) 09 08 07 06 05 04 03 02 THANK YOU! We are grateful you chose KENWOOD for your land mobile applications. We believe this easy-to-use transceiver
More informationRemote Rig Control. By Chris Bigelow, VA3ECO
Remote Rig Control By Chris Bigelow, VA3ECO Whether you are away from home for work or pleasure, it s hard to lug your radio and antenna with you. I faced this problem recently and found setting up a remote
More informationUse of Voter Comparators to Improve Railroad Radio Communications
Use of Voter Comparators to Improve Railroad Radio Communications Purpose This Application Note will describe the use of the SNV-12 Voter Comparator to expand radio coverage in railroad applications. Introduction
More informationENCORE 200 VHF Bass Wireless Microphone System
ENCORE 200 VHF Bass Wireless Microphone System Nady Wireless Systems are type accepted under FCC rules parts 90, 74 and 15. The device complies with RSS-210 of Industry & Science Canada. Operation is subject
More informationMidland 248XL I NSTRUCTION GUI DE
Midland 248XL I NSTRUCTION GUI DE INDEX Introduction...2 Function and location of the controls...3 Installation...7 Power supply...7 Installing an antenna...7 How to use your Midland 248XL...8 Frequency
More informationHR MHZ AM-FM AMATEUR RADIO HF TRANSCEIVER OWNER'S MANUAL. Content of the packaging
HR-2800 28 MHZ AM-FM AMATEUR RADIO HF TRANSCEIVER OWNER'S MANUAL NOTICE! It is recommended to carefully read this owner s manual before using the product. This will also help to prevent illegal use of
More informationPC to Radio Audio and Key-line Interface
PC to Radio Audio and Key-line Interface Background - This simple interface was developed to capacitive couple audio signals between a radio and PC, to provide a means of adjusting audio levels between
More informationDX 33HML. Full Channel AM/FM Mobile Transceiver OWNER S MANUAL. Printed In Malaysia AT H PD000802
DX 33HML Full Channel AM/FM Mobile Transceiver Printed In Malaysia AT3601014H PD000802 OWNER S MANUAL TABLE OF CONTENTS Page Specification.................................... 2 Installation Location.....................................
More informationMASTR II AUXILIARY RECEIVER 19D417546G7 & G8 & ANTENNA MATCHING UNITS 19C321150G1-G2. Maintenance Manual LBI-30766L. Mobile Communications
L Mobile Communications MASTR II AUXILIARY RECEIVER 19D417546G7 & G8 & ANTENNA MATCHING UNITS 19C321150G1-G2 Printed in U.S.A Maintenance Manual TABLE OF CONTENTS Page SPECIFICATIONS.....................................................
More informationIntroduction Pag. 1. Function and location of the controls Pag. 2. Installation Pag. 3. Power supply Pag. 3. Installing an antenna Pag.
ALAN 121 INDEX Introduction Pag. 1 E N G L I S H Function and location of the controls Pag. 2 Installation Pag. 3 Power supply Pag. 3 Installing an antenna Pag. 4 How to operate with your transceiver Pag.
More informationDEM Part Number L144-28INTCK 144 MHz Transverter Kit and complete kit
DEM Part Number L144-28INTCK 144 MHz Transverter Kit and complete kit Power Out: Noise Figure and Gain: DC Power Requirement: 50 mw linear minimum 3.5 db NF nominal, 5 dbg maximum 12-15.5 VDC, 13.8 nominal
More informationUser Manual. Specifications...3. Control and Operation Microphone...8. Installation...9. Installation of Main Unit...9
Contents Specifications...3 Control and Operation...4-7 Microphone...8 Installation...9 Installation of Main Unit...9 Antenna Installation...9 Operational test...9 Frequency Bands Table...10 Frequency
More information