P1-04DAL-1 Analog Output

Transcription

1 Output Specifications Output Channels Output Range ma Signal Resolution -bit Resolution Value of SB (least significant bit) Data Range 9 counts Output Type Output Value in Fault Mode ess than ma oad Impedance Maximum Inductive oad Allowed oad Type Maximum Inaccuracy Full Scale Calibration Error Offset Calibration Error Accuracy vs. Temperature Max Crosstalk at DC, Hz and Hz inearity Error (End to End) Output Stability and Repeatability Output Ripple Output Settling Time All Channel Update Rate Maximum Continuous Overload Type of Output Protection Output Signal at Power Up and Power Down External Power Supply Required ma =.9 µa / count SB = count Current sourcing at ma max Ω (9. VDC), 9 Ω (. VDC), 8 Ω (. VDC), 9 Ω (. VDC), Ω (. VDC) Minimum oad: C C ambient temperature mh Grounded % of range ±.% of range minimum ±.% of range maximum ± PPM / C maximum full-scale calibration change (±.% of range / C) -db, SB ± counts max., (±.% of full scale) ±% counts after min. warm up (typical) ±.% of full scale. ms max., µ min. (full scale range) ms (max) Outputs open circuit protected Electronically current limited to ma or less ma VDC (-% / ma (oop Power Included) P-DA- V I+ I+ I+ I+ V -ma OUT ANAOG P-DA- Analog Output The P-DA- ow Resolution Analog Output Module provides four current sourcing channels for converting a digital value of 9 (-bit) to ma analog signals for use with the Productivity system. Output Specifications General Specifications Removable Terminal Block Specifications Wiring Diagram and Schematic Module Installation Procedure QR Code Wiring Options Module Configuration inear Scaling Non-inear Scaling Typical Application Example Warning Terminal Block sold separately, (see wiring options on page ). Warranty: Thirty-day money-back guarantee. Two-year limited replacement. (See for details). Sales 8--

2 General Specifications Operating Temperature º to ºC (º to ºF) Storage Temperature -º to ºC (-º to 8ºF) Humidity to 9% (non-condensing) Environmental Air No corrosive gases permitted Vibration IEC8-- (Test Fc) Shock IEC8-- (Test Ea) Field to ogic Side Isolation 8VAC applied for second Insulation Resistance > VDC Heat Dissipation mw Maximum Enclosure Type Open Equipment Module ocation Any I/O position in a Productivity System Field Wiring Removable terminal block (sold separately). Use ZIPink Wiring System optional See Wiring Options on page. EU Directive See the EU Directive topic in the Productivity Suite Help File. Information can also be obtained at: Terminal Type (sold separately) -position Removable Terminal Block Weight 8. g (. oz) Agency Approvals U -- file E99, Canada & USA CE (EN- EMC and EN-- Safety)* *See CE Declaration of Conformance for details. Terminal Block Specifications Part Number P-RTB P-RTB- Positions Screw Terminals Spring Clamp Terminals Wire Range AWG (.. mm²) Solid / Stranded Conductor / in (. mm) Insulation Max. / in ( mm) Strip ength 8 AWG (.8. mm²) Solid / Stranded Conductor / in (. mm) Insulation Max. 9/ in ( 8 mm) Strip ength Conductors USE COPPER CONDUCTORS, ºC or equivalent. Screw Driver. in (. mm) Maximum* Screw Size M N/A Screw Torque. lb in (.8 N m) N/A *Recommended Screw Driver TW-SD-MS- Tech Support -8-

3 8 9 P-DA- Schematic P-DA- Wiring Diagram VDC User Supplied Power - + I+ I+ I+ I+ V INTERNA MODUE CIRCUITRY ma current sourcing ma current sourcing ma current sourcing ma current sourcing ISOATED ANAOG CIRCUIT POWER CH DAC CH DAC CH DAC CH DAC ma oad Current Source Output Circuit ISOATED ANAOG CIRCUIT MON Note: Shield is connected to common at the source device. Sales 8--

4 Module Installation QR Code WARNING: Do not add or remove modules with field power applied. Step One: With latch gram ring Dia TD Wi P-8 e Single r Sourc Powe P-8TD P-8TD in locked position, align connectors on the side of each module and stack by pressing together. Click indicates lock is engaged VDC e r Sourc Powe Dual V + Use any QR Code reader application to display the module s product insert. WIRE STRIP ENGTH MAX MIN OCK Step Three: To unstack modules, pull locking latch up into the unlocked position and then pull modules apart. - Tech Support -8- V VDC Check all latches are secure after modules are connected VDC P-8TD UNOCK V 8 9 Step Two: Attach field wiring using the removable terminal block or ZIPink wiring system. V

5 Wiring Options ZIPink Connection System Cable + ZIPink Module = Complete System ZIPink pre-wired terminal block s. m (. ft). m (. ft). m (. ft) Z-P-CB Z-P-CB- Z-P-CB- Module Configuration Using the Hardware Configuration tool in the Productivity Suite programming software, drag and drop the P-DA- module into the configuration. If desired, assign a User Tagname to each output point channel selected and to each Status Bit Item. Z-RTB- Z-RTB ZIPink Modules Feed through Z-RTB Z-RTB- Terminal Block with pigtail. m (. ft). m (. ft) Z-P-CB-P Z-P-CB-P Screw Terminal Block only P-RTB (Quantity ) Spring Clamp Terminal Block only P-RTB- (Quantity ) Sales 8--

6 inear Scaling Non-inear Scaling The Scale (inear) function can be used to: Convert an application specific range to range which is native to the analog output module. Make other linear conversions in ranges appropriate to the application. The Scale (Non-inear) function can be used for Non-inear applications. evel Transmitter Tank evel Display Gauge Motor Speed 9 Motor Driver Select the Input and Output tags appropriate for the application. Convert raw input signals to engineering units for use in the program, or convert engineering units to output signals for control purposes max..... Enter actual output values for each input value break point. min min max Tech Support -8-

7 Sales 8--

8 WARNING: To minimize the risk of potential safety problems, you should follow all appli local and national codes that regulate the installation and operation of your equipment. These codes vary from area to area and it is your responsibility to determine which codes should be followed, and to verify that the equipment, installation, and operation are in compliance with the latest revision of these codes. Equipment damage or serious injury to personnel can result from the failure to follow all appli codes and standards. We do not guarantee the products described in this publication are suitable for your particular application, nor do we assume any responsibility for your product design, installation, or operation. If you have any questions concerning the installation or operation of this equipment, or if you need additional information, please call Technical Support at -8-. This publication is based on information that was available at the time it was printed. At AutomationDirect.com we constantly strive to improve our products and services, so we reserve the right to make changes to the products and/or publications at any time without notice and without any obligation. This publication may also discuss features that may not be available in certain revisions of the product. Document Name Edition/Revision Date P-DA--DS st Edition 9// Copyright, AutomationDirect.com Incorporated/All Rights Reserved Worldwide 8 Tech Support -8-