M4000 with M23 connection

Transcription

1 ADDENDUM TO OPERATING INSTRUCTIONS with M connection Multiple Light Beam Safety Device GB

2 Addendum This document is protected by the law of copyright, whereby all rights established therein remain with the company SICK AG. Reproduction of this document or parts of this document is only permissible within the limits of the legal determination of Copyright Law. Alteration or abridgement of the document is not permitted without the explicit written approval of the company SICK AG. SICK AG Industrial Safety Systems Germany All rights reserved 00/00-0-

3 Addendum Content Content About this document... Electrical installation.... System connection M x + FE Standard, Standard A/P, Standard Curtain..... Connection Reset M.... System connection M x + FE Advanced, Advanced A/P, Advanced Curtain..... Extension connection M + FE für UE0.... System connection M x + FE Area 0/0.... System connection M x + FE / M x + FE Standard S00, S00, S00 Standard A/P S Technical specifications.... Dimensional drawings... Ordering information.... with M.... Accessories... 00/00-0- SICK AG Industrial Safety Systems Germany All rights reserved

4 Chapter About this document Addendum About this document Note This addendum provides information on the special features and properties of the multiple light beam safety devices with M. This addendum is applicable to the multiple light beam safety devices with the following entry on the type label in the field Operating Instructions: 00 und 00. This document is part of SICK part number 00 (Addendum " with M connection" operating instructions in all available languages). This addendum applies only in combination with the underlying operating instructions " Standard and Standard A/P multiple light beam safety device" (SICK Art. No. 00) or " Advanced, Advanced A/P and Area 0/0 cmultiple light beam safety device" (SICK Art. No. 00). It is imperative that you read this addendum and the underlying operating instructions before you mount, install and start up the device. SICK AG Industrial Safety Systems Germany All rights reserved 00/00-0-

5 Addendum Chapter Electrical installation Electrical installation Note The plug alignment (direction of turn) in the housing may vary from device to device. You can identify the correct pin assignment by the position of the pins in relation to each other.. System connection M x + FE Standard, Standard A/P, Standard Curtain Fig. : Pin assignment M x + FE Standard 0 0 Tab. : Pin assignment M x + FE Standard Pin Wire colour Sender Receiver or Standard A/P Brown Input V DC (voltage supply) Input V DC (voltage supply) Blue 0 V DC (voltage supply) 0 V DC (voltage supply) Grey Test input: 0 V: external test active V: external test inactive OSSD (output signal switching device ) Pink Reserved OSSD (output signal switching device ) Red Reserved Reset/restart Yellow Reserved External device monitoring (EDM) White Reserved Application diagnostic output (ADO) Red/blue Reserved Reserved Black Reserved Reserved 0 Purple Reserved Reserved Grey/pink Reserved Reserved Green Functional earth Functional earth 00/00-0- SICK AG Industrial Safety Systems Germany All rights reserved

6 Chapter Electrical installation Addendum Fig. : Pin assignment for connection Reset M.. Connection Reset M Tab. : Pin assignment for connection Reset M Note Pin Wire colour Receiver or Standard A/P Brown V DC output (auxiliary voltage for reset button) White Output Reset required Blue 0 V DC Black Reset/restart interlock Grey Reserved The connection Reset is an additional connection. It is on the receiver. SICK AG Industrial Safety Systems Germany All rights reserved 00/00-0-

7 Addendum Chapter Electrical installation Fig. : Pin assignment M x + FE Advanced. System connection M x + FE Advanced, Advanced A/P, Advanced Curtain 0 0 Tab. : Pin assignment M x + FE Advanced Pin Wire colour Sender Receiver or Advanced A/P Brown Input V DC (voltage supply) Input V DC (voltage supply) Blue 0 V DC (voltage supply) 0 V DC (voltage supply) Grey Test input: 0 V: external test active V: external test inactive OSSD (output signal switching device ) Pink Reserved OSSD (output signal switching device ) Red Reserved Reset/restart or Reset/override (combined) Yellow Reserved External device monitoring (EDM) White Reserved Application diagnostic output (ADO) Red/blue Reserved Reset required Black Device communication (EFI A ) Device communication (EFI A ) 0 Purple Device communication (EFI B ) Device communication (EFI B ) Grey/pink Reserved Belt stop/c (only in conjunction with external switching amplifier or bus node) Green Functional earth Functional earth 00/00-0- SICK AG Industrial Safety Systems Germany All rights reserved

8 Chapter Electrical installation Addendum Notes For the connection of pin and 0 only use cable with twisted cores, e.g. the SICK connection cables available as accessories (see section. Accessories on page ). If you use the UE0 switching amplifier at the extension connection of the, you may not connect any other SICK device to the connections pin and pin 0 (EFI device communication) of the with the exception of the SICK-EFI gateways. If you do not use a SICK-EFI gateway on the pin and pin 0 (EFI device communication), to improve the EMC behaviour we recommend the termination of the connections pin and 0 (EFI device communication) on the in the control cabinet using a resistor of (SICK part number 0) in particular if you use the combination Advanced or Advanced A/P with the UE0 switching amplifier at the extension connection... Extension connection M + FE für UE0 Fig. : Pin assignment extension connection M + FE FE Tab. : Pin assignment extension connection M + FE Pin Advanced Receiver or Advanced A/P V DC output (voltage supply UE0) Device communication (EFI A ) 0 V DC (voltage supply UE0) Device communication (EFI B ) FE Functional earth SICK AG Industrial Safety Systems Germany All rights reserved 00/00-0-

9 Addendum Chapter Electrical installation Fig. : Pin assignment M x + FE Area 0/0. System connection M x + FE Area 0/0 0 0 Tab. : Pin assignment M x + FE Area 0/0 Pin Wire colour Sender Receiver Brown Input V DC (voltage supply) Input V DC (voltage supply) Blue 0 V DC (voltage supply) 0 V DC (voltage supply) Grey Test input: 0 V: external test active V: external test inactive OSSD (output signal switching device ) Pink Reserved OSSD (output signal switching device ) Red Reserved Reset/restart Yellow Reserved External device monitoring (EDM) White Reserved Application diagnostic output (ADO) Red/blue Reserved Reset required Black Device communication (EFI A ) Device communication (EFI A ) 0 Purple Device communication (EFI B ) Device communication (EFI B ) Grey/pink Reserved Reserved FE Green Functional earth Functional earth Notes For the connection of pin and 0 only use cable with twisted cores, e.g. the SICK connection cables available as accessories (see section. Accessories on page ). If you do not use either a SICK switching amplifier or a SICK bus node on the system connection pin and 0 (EFI device communication), to improve the EMC behaviour we recommend the termination of the connections pin and 0 (EFI device communication) on the in the control cabinet using a resistor of (SICK part number 0). 00/00-0- SICK AG Industrial Safety Systems Germany All rights reserved

10 Chapter Electrical installation Addendum. System connection M x + FE / M x + FE Standard S00, S00, S00 Standard A/P S00 Fig. : Pin assignment M x + FE / M x + FE Standard S00, S00, S00 Standard A/P S00 0 Tab. : Pin assignment M x + FE / M x + FE Standard S00, S00, S00 Standard A/P S00 Pin Sender Receiver or Standard A/P Input V DC (voltage supply) Input V DC (voltage supply) 0 V DC (voltage supply) 0 V DC (voltage supply) Reserved OSSD (output signal switching device ) Test input: OSSD (output signal switching device ) 0 V: external test active V: external test inactive Reserved Reset/restart Reserved External device monitoring (EDM) Functional earth Application diagnostic output (ADO) Reserved Functional earth Reserved Reserved 0 Reserved Reserved Reserved 0 SICK AG Industrial Safety Systems Germany All rights reserved 00/00-0-

11 Addendum Chapter Technical specifications Technical specifications. Dimensional drawings Fig. : Dimensional drawing M system connection (mm) 00/00-0- SICK AG Industrial Safety Systems Germany All rights reserved

12 Chapter Ordering information Addendum Ordering information. with M The article numbers for devices with M are available on request. Tab. : Part numbers accessories. Accessories Part Part number Connecting cables for with M x + FE: Socket straight, stripped, m 0 Socket straight, stripped, 0 m 0 Socket straight, stripped, m 0 Notes The minimum bending radius of the cables is 0 mm. The cable sheath is made of PVC (UL listed). The specified connection cables cannot be used for Standard S00, S00 and S00 or Standard A/P S00. SICK AG Industrial Safety Systems Germany All rights reserved 00/00-0-

13 00/ XX/XX. Printed in Germany (00-0). Subject to change without notice. The specified product features and technical data do not represent any guarantee. 0 A sw int Australia Phone tollfree sales@sick.com.au Belgium/Luxembourg Phone + (0) info@sick.be Brasil Phone sac@sick.com.br Ceská Republika Phone sick@sick.cz China Phone +- ghk@sick.com.hk Danmark Phone sick@sick.dk Deutschland Phone info@sick.de España Phone info@sick.es France Phone info@sick.fr Great Britain Phone + (0) info@sick.co.uk India Phone + 0 info@sick-india.com Italia Phone + 0 info@sick.it Japan Phone + (0) support@sick.jp Nederlands Phone + (0)0 info@sick.nl Norge Phone austefjord@sick.no Österreich Phone + (0) -0 office@sick.at Polska Phone info@sick.pl Republic of Korea Phone +- / kang@sickkorea.net Republika Slowenija Phone + (0)- 0 office@sick.si Russia Phone + 0 denis.kesaev@sickautomation.ru Schweiz Phone + contact@sick.ch Singapore Phone + admin@sicksgp.com.sg Suomi Phone sick@sick.fi Sverige Phone info@sick.se Taiwan Phone + - sickgrc@ms.hinet.net Türkiye Phone info@sick.com.tr USA/Canada/México Phone +() tollfree info@sickusa.com More representatives and agencies in all major industrial nations at SICK AG Waldkirch Germany