Installer Guide. Read Me First... PA 8 ELITE PA 8 ULTRA ELITE PA 16 ELITE. Multi-Channel Power Amplifiers. If you need help...

Transcription

1 Installer Guide PA 8 ELITE PA 8 ULTRA ELITE PA 6 ELITE Multi-Channel Power Amplifiers Read Me First... If you need help.... Check the online help of the Web Installer Interface.. Check our website support page. 3. Contact our support team: support@stormaudio.com

2 Welcome What s In the Box Thank you for choosing a StormAudio Multi-Channel Amplifier. This guide provides step-by-step instructions for setting up your PA. The PA range is based on a common Class D technology delivering high grade performance and sonical quality. This guide will describe the connectivity of each model. Installer Guide Safety Instructions Multi-Channel Amplifier Power cord * * depending on the region, the power cord will be delivered with Fuse to be installed

3 Before You Begin. In case the AC cord is delivered with Fuses attached, make sure to install them before connecting the unit.. Ensure your electrical circuit has a good ground connection with all audio equipment connected to the same ground node to avoid ground loop. 3. Required equipment: Multi-Channel Amplifier Audio Processor XLR cables Mono Jack 3.5mm cables Speakers with cables LAN router with Cat5/6 RJ5 cable * * the PA needs a DHCP server to be part of the network to get an IP address allocated. Make sure to check your Internet Provider box or LAN/Switch box for router function.

4 Installation Flow The installation of the PA shall be made following below steps that will be described along this guide. Audio inputs and control connectivity Audio outputs connectivity 7 3 Trigger control 0 Power Up and function description 5 Connectors description 6 Specifications 5 3

5 Hardware Connections Inputs PA 8 ELITE PA 8 ULTRA ELITE PA 6 ELITE.) The PA 8 ELITE is made of Master Modules and Slave Modules with the Power Supplies located in the Master Modules. We recommend that most consuming speakers such as LCR and Subwoofers should be connected to the Master Modules, that is to say: Input/Output,, 5 and 6..) Connect the unit as shown below. 3. Check Fuse and install the proper Fuse if required.. Connect AC cord to Power Outlet (do not turn ON now) 3. Connect the RJ5 LAN Network cable to the router/switch. Connect your Analog inputs via XLR (see part 5 for connectors description)

6 Hardware Connections Inputs PA 8 ELITE PA 8 ULTRA ELITE PA 6 ELITE.3) The PA 8 ULTRA ELITE offers the possibility to provide more power by bridging its outputs. On a per pair basis, you can decide to bridge them. When Bridging is required, change the position of the Switch () to Bridge and make use of the inputs, 3, 5 and 7 (shown in orange below) Check Fuse and install the proper Fuse if required.. Connect AC cord to Power Outlet (do not turn ON now) 3. Connect the RJ5 LAN Network cable to the router/switch. Position the switch according to the required output mode: Normal or Bridged 5. Connect your Analog inputs via XLR (see part 5 for connectors description) 5

7 Hardware Connections Inputs PA 8 ELITE PA 8 ULTRA ELITE PA 6 ELITE.) The PA 6 ELITE is made of Master Modules and Slave Modules with the Power Supplies located in the Master Modules. We recommend that most consuming speakers such as LCR and Subwoofers should be connected to the Master Modules, that is to say: Input/Output,, 5, 6, 9, 0, 3 and..5) Connect the unit as shown below. 3. Check Fuse and install the proper Fuse if required.. Connect AC cord to Power Outlet (do not turn ON now) 3. Connect the RJ5 LAN Network cable to the router/switch. Connect your Analog inputs via XLR (see part 5 for connectors description) 6

8 Hardware Connections Outputs PA 8 ELITE PA 8 ULTRA ELITE PA 6 ELITE.) Connect the unit as shown below. Make sure to follow the recommendation made on part. about splitting the most consuming speakers in channels,, 5 and 6. Connect your Analog outputs. We have used high quality binding posts supporting «banana plug», wire up to.5mm² and fork. The connector is isolated to limit risk of short between outputs. 7

9 Hardware Connections Outputs PA 8 ELITE PA 8 ULTRA ELITE PA 6 ELITE.) Connect the unit as shown below. + -! + - NORMAL MODE BRIDGED MODE Connect your Analog outputs. We warn you to be careful with the connection at this stage. Depending on the Output mode selected in.3, you must wire the outputs according to above description: - in green is shown a Normal (Single Ended) connection,! - in orange is shown the wiring you must follow for the Bridged mode. Note: when in Bridged mode, the output channel number is the one with the «+» connection. In above illustration, the corresponding input is channel 3. 8

10 Hardware Connections Outputs PA 8 ELITE PA 8 ULTRA ELITE PA 6 ELITE.3) Connect the unit as shown below. Make sure to follow the recommendation made on part. about splitting the most consuming speakers in channels,, 5, 6, 9, 0, 3 and. Connect your Analog outputs. We have used high quality binding posts supporting «banana plug», wire up to.5mm² and fork. The connector is isolated to limit risk of short between outputs. 9

11 3 Hardware Connections Trigger Control. The PA can be controlled remotely by the StormAudio ISP (Immersive Sound Processor) or an external controller via its Trigger Input. You must setup your controller Trigger output to V Active Status. The PA will react to a rising edge to power up.. If you need to control several amplifier units, you can daisy chain the Trigger control. It is internally delayed by s between Input and Output. The Trigger interfaces use a standard 3.5mm mono jack connector. A wire as shown herewith is recommended. ( + ) (- ) 0

12 Power Up and Function description Power Up Information Protections.) Power up sequence. 3. Turn the Main Switch to ON (I) on the back panel.. Front panel LED will blink red few seconds and will then remain red, unit is in Sleep Mode. 3. When in Sleep Mode, press the Power Button or activate the Trigger in your controller. Unit will start blinking red for a few seconds before turning to green.

13 Power Up and Function description Power Up Information Protections.) The front panel LED is used to indicate statutory informations as well as protection feedback..3) The statutory informations are described in the table below : Unit is in Sleep Mode Unit is Initializing In this mode the unit is turned off. It can be activated via the Triggers or the the Network. From the Sleep Mode to On Mode and vice versa, the unit has to be initialized and properly turned off. This only lasts for a few seconds with no sound. RED Fixed RED Blinking Unit is Upgrading The PA firmware can be upgraded over the Network. When this occurs, the unit falls in a specific mode with no other activity possible. GREEN Blinking Unit is in On Mode The PA is in its normal playback mode with no failure detected. GREEN Fixed

14 Power Up and Function description Power Up Information Protections.) The PA range includes a set of protection mechanisms to ensure its best reliability. The system will react to the following event: - Fan Failure : An active cooling regulation is integrated powered by no less than 6 low noise high speed capable fans. Although extremely reliable over the product s life cycle, we continuously monitor the fans for proper functioning. - Overheat : In very extreme conditions such as high power demand in an extreme high temperature environment, the heat dissipation can reach temperatures that can harm the unit if not managed properly. - Overcurrent : To prevent shortage at the output that can damage the amplifier stages, the output current is monitored continuously. - Overvoltage : Amplifier stages can be damaged in a few occasions. Overvoltage at the power supply level is one of them. To prevent from failure to occur in such event, we are monitoring the supply rails..5) The Protection Mechanism is described in the table below. Unit Overheat An ambiant temperature sensor measures the internal temperature. If >60 C, the unit will go to Sleep Mode. In case PA is controlled via Trigger, unit will restart with T<55 C. YELLOW/RED Chaser Overcurrent / Overvoltage Module malfunction The unit will MUTE the channels that are showing the problem. This will be released automatically. YELLOW Blinking Module Overheat Each amplifier module is monitored for temperature. The unit will MUTE the channels automatically when threshold is reached. This will be released automatically. YELLOW/RED Chaser FAN failure A FAN failure will not prevent the unit from working correctly. Overheat protection might nevertheless be triggered more easily. YELLOW Fixed 3

15 5 Hardware Connections Connectors description Special care must be taken of for the cables, wires and connectors to be used with the PA. Here is a description of the connectors pin out and recommendation for the wiring. 5.) To connect the PA to an ISP or a processor, you must use male to female XLR cables. The connector in the PA is a Female XLR. We recommend cables up to 3m. 5.) In some cases, it might be required to connect to processors with unbalanced outputs. In such case, the wiring should be done as shown.

16 6 Specifications PA 8 ELITE PA 6 ELITE Amplifier Class Class D Class D Channel configuration Output power channels driven SE = Single Ended, BTL = Bridged Tied Load PA 8 ULTRA ELITE Class D SE - 8 SE - 6 SE - 8 (Normal) BTL - (Bridged) RMS 8 Ω : khz 0.% distortion 00 W 00 W 00 W 800 W RMS 8 Ω : khz % distortion 50 W 50 W 50 W 000 W Output power All channels driven RMS 8 Ω : 0 Hz - 0 khz 0.% distortion 00 W 00 W 00 W 800 W Frequency response High : -3 db CEM 50 khz 50 khz 50 khz 50 khz Low : -3 db CEM 0 Hz 0 Hz 0 Hz 0 Hz Signal / Noise Ratio (A-Weighted) Referred to P-rated > 5 db > 5 db > 5 db > 5 db THD (0Hz-0kHz), Watt to -db max. power < 0,03% < 0,03% < 0,03% < 0,03% Gain Standard 6 db 6 db 6 db 3 db Damping factor > 00 > 00 Power Supply Voltage range 0V to 0V 0V to 0V Type SWITCHING MODE SWITCHING MODE > 00 0V to 0V SWITCHING MODE Casing Range selection Universal Universal Home / Rack (removable ears) Size 3RU 3RU Note: Specifications are subject to change without notice Universal 3RU 5