RUN HLD MAN PRG. Features

Transcription

1 DCP3 Digital Controller Programmer / Page 1 of 16 Specification Function The DCP3 is a high-function digital controller programmer supporting up to 19 program profiles with up to 3 segments per profile. A universal input accepts thermocouple signals, resistance temperature detector (RTD) signals, dc voltages and dc currents. DCP31 is a single channel (1 input) version. DCP32 is a dual channel model with 2 inputs and 2 loops. A temperature and relative humidity calculation model which controls temperature and relative humidity is selectable on DCP32. The DCP3 supports extensive digital I/O functions including 3 event outputs, 5 time events (optional) and 12 external switch inputs (8 optional). Up to 2 auxiliary outputs can also be added on as an option. DCP32 has only 1 auxiliary output available. PROG SEG PV SP 193 OUT RUN HLD MAN PRG EV1 EV2 EV3 TM CYC CH1 CH BAT AT OT1 OT2 OT3 T1 T2 T3 T4 T5 PROG RUN/HOLD DISP RESET ADV Honeywell Figure 1 The DCP3 Digital Controller Programmer Features Input 1 Accuracy = ±.1 % FS (Input 2 Accuracy = ±.2 % FS). High-speed sampling time of.1 seconds. Any input type can be selected by key operation. A maximum of 19 program profiles can be stored and up to 3 segments can be programmed to each profile. Three event outputs for PV, deviation, controller mode or other states are standard. Twelve external switch inputs (eight optional) allow remote selection of program numbers or operation. Up to eight frequently changed parameter setups can be registered to the PARA key. Universal AC power supply within range of 9 Vac to 264 Vac, 5/6 Hz. CE mark compliant applicable standards: EN611-1, EN581-2, EN582-2 Wide range of optional functions enables use in an extensive range of applications: 5 time event outputs 8 digital inputs 2 auxiliary outputs on DCP31; 1 auxiliary output on DCP32 Relative Humidity model available on DCP32. Sensing and Control, 11 West Spring Street, Freeport, Illinois 6132 Printed in U.S.A. Copyright 1999 Honeywell Inc.

2 Page 2 Basic Function Blocks of DCP31/32 PV Inputs DCP31 (1 input only) DCP32 (2 inputs) Thermocouple Resistance Temperature detector (RTD) DC current (Input 1 only) DC voltage 4 External Switch Inputs RUN HOLD RESET ADV Console Display selection Program No. selection RUN/HOLD ADVANCE RESET AUTO/MANUAL AT Parameter setup Program setup Filter Root extraction Input bias Linearization table approximation 8 External Switch Inputs Program No. FAST PV start AUTO/MANUAL AT G.Soak cancel Forward/reverse action Motor feedback (MFB) input Power Supply 9 to 24 Vac 19 Profiles Control Operation Block Control Outputs Current Heat-cool Position Proportional Relay Voltage 3 Event Outputs PV Deviation MFB Time event SP MV Status event Absolute value deviation 5 Time Event Outputs Time event Segment code 2 Auxiliary Outputs PV SP Deviation 1 Loop only Option MV MFB Output change limiter Upper/lower limiter SP output MV1/MV2 change (DCP32: 1 only) Specifications Program Number of Programs Number of Segments Segment Setting System Segment Time 19 maximum 3 per program maximum RAMP-X system: Set by setpoints (SP1, SP2) and time. to 99 hours 59 minutes; or to 99 minutes 59 seconds (time unit selectable) Basic Time Accuracy ±.1 % (.1 second delay when segment time setting is ) Events (3) Time Events (5) PID Set Number (each channel) Guarantee Soak (each channel) PV Start Sets operating point. Sets ON and OFF times. Sets to 8. (Set for continuation of previous segment.) (Set to 4 on heat/cool models.) Sets G.Soak width units to 1 units. Sets program ON/OFF and channel. Cycle Sets program count to Pattern Link Tag Sets program number to 19 (: no link). Sets 8 alphanumerics for each program (not displayed on controller).

3 Page 3 Specifications, continued Input 1 Input Type Thermocouple, resistance temperature detector, dc voltage, dc current multi-range (Table 1) Input Readout Accuracy ±.1 % FS ± 1 unit (varies according to standard conditions, display value conversion and range) At 1 C maximum of K and T thermocouples: At 26 C maximum of B thermocouple: At 26 C to 8 C: At 8 C to 18 C: At 1 C maximum of R and S thermocouples: At 1 C to 16 C: At 3 C maximum of PR4-2 thermocouple: At 3 C to 8 C: At 8 C to 19 C: Golden iron chromel thermocouple: F1, F33, F38, P1, P33 and P38 ranges by resistance thermometer detector input: At mv to 1 mv range: At 1 C maximum of DIN U thermocouple: At 1 C to C: At 1 C maximum of DIN L thermocouple: ± 1 C ± 1 unit ± 4. % FS ± 1 unit ±.4 % FS ± 1 unit ±.2 % FS ± 1 unit ±.2 % FS ± 1 unit ±.15 % FS ± 1 unit ± 2.5 % FS ± 1 unit ± 1.5 % FS ± 1 unit ±.5 % FS ± 1 unit ± 1.5K ± 1 unit ±.15 % ± 1 unit ±.15 % FS ± 1 unit ± 2 C ± 1 unit ± 1 C ± 1 unit ± 1.5 C ± 1 unit Input Sampling Cycle Input Bias Current Input Impedance Measuring Current Influence of Wiring Resistance.1 seconds Thermocouple, dc voltage input: ± 1.3 $PD[LPXPDWSHDNYDOXHXQGHUVWDQGDUG conditions). At 1 V minimum range: 3 $PD[LPXP DC current input: 5 Ÿ XQGHURSHUDWLQJFRQGLWLRQV RTD input: 1.4 ma ±.2 ma, current flow from terminal A (under operating conditions) Thermocouple, dc voltage input: Changes in readout value at wiring resistance of 25 ŸDW both ends are as follows by input conversion: mv to 1 mv, 1 mv to +1 mv: Within 35 9 mv to 1 mv: Within 6 9 Other: Within 75 9 RTD input: ±.1 % FS/ŸPD[LPXPLQZLULQJUHVLVWDQFHUDQJHŸWRŸ5DQJHRI) F33, F38, P1, P33, and P38: ±.2 % FS/ŸPD[LPXP RTD Input Allowable Wiring Resistance Allowable wiring resistance is 85 ŸPD[LPXP,QFOXGLQJZener barrier resistance. When Zener barrier is used, this applies only to ranges other than F1, F33, F38, P1, P33, and P38. Note that site adjustment is required.) Allowing wiring resistance is 1 ŸPD[LPXP7KLVDSSOLHVWRUDQJHV)))3 P33, and P38. Note that the Zener barrier cannot be used.) Allowable Parallel Resistance Maximum Allowable Input Burnout Thermocouple disconnection detection allowable parallel resistance: 1 MŸPLQLPXP Thermocouple, dc voltage input: 5 Vdc to +15 Vdc DC current input: 5 ma dc; 2.5 Vdc Upscale and downscale can be internally selected. (DC current input and dc voltage input ranges of 1 V or more are only downscaled.)

4 Page 4 Specifications, continued Input 1, continued Over-range Detection Threshold Cold Junction Compensation Accuracy Influence of Ambient Temperature on Cold Junction Compensation Cold Junction Compensation System Scaling Square Root Extraction Linearization Table Approximation Input Bias 11 % FS minimum: Upscale 1 % FS maximum: Downscale (Note that F5 range is not downscaled. Lower readout limit of B18 range is 2 C.) ±.5 C (under standard conditions) ±.2 C (in range C to 5 C) Internal/external ( C only) compensation selectable 1999 units to units (Settable by dc voltage and dc current. Reverse scaling and decimal point repositioning possible.) Dropout.1 % to 1. %. Possible by dc current and voltage ranges. 12 (both line ends fixed, 11 points variable) 1 units to +1 units variable Digital Filter. sections to 12. seconds variable (filter OFF at.) Input 2 (DCP32 only) Input Type Thermocouple, resistance temperature detector, dc voltage, multi-range (Table 2) Input Readout Accuracy Input Sampling Cycle Input Bias Current Measuring Current Influence of Wiring Resistance ±.2 % FS ± 1 unit (varies according to standard conditions, display value conversion).1 seconds Thermocouple: ± 2. $PD[LPXPXQGHUVWDQGDUGFRQGLWLRQV DC voltage input: ± 5 $PD[LPXPXQGHUVWDQGDUGFRQGLWLRQV RTD input:.64 ma ±.2 ma, current flow from terminal A (under operating conditions) Thermocouple, dc voltage input: Changes in readout value at wiring resistance of 25 ŸDW both ends are as follows by input conversion: RTD: Within 3 9 DC voltage: Within 75 9 RTD input: ±.1 % FS/ŸPD[LPXPLQZLULQJUHVLVWDQFHUDQJHWRŸ5DQJHRI)DQG P1: ±.2 % FS/ŸPD[LPXP RTD Input Allowable Wiring Resistance Allowable wiring resistance is 85 ŸPD[LPXP,QFOXGLQJZener barrier resistance. When Zener barrier is used, this applies only to ranges other than F36 and P36. Note that site adjustment is required.) Allowing wiring resistance is 1 ŸPD[LPXP7KLVDSSOLHVWRUDQJHV)DQG31RWHWKDW the Zener barrier cannot be used.) Allowable Parallel Resistance Maximum Allowable Input Burnout Thermocouple disconnection detection allowable parallel resistance: 1 MŸPLQLPXP Thermocouple:.3 Vdc to +5 Vdc DC voltage input: 1 Vdc to +11 Vdc Thermocouple: Upscale DC voltage input: Downscale

5 Page 5 Specifications, continued Input 2 (DCP32 only), continued Over-range Detection Threshold Cold Junction Compensation Accuracy Influence of Ambient Temperature on Cold Junction Compensation Cold Junction Compensation System Scaling Square Root Extraction Linearization Table Approximation Input Bias 11 % FS minimum: Upscale 1 % FS maximum: Downscale (Note that the range of L7 is downscaled at 1 % FS or less.) ±.7 C (under standard conditions) ±.2 C (in range C to 5 C) Internal/external ( C only) compensation selectable 1999 units to units (Settable by dc voltage range. Reverse scaling and decimal point repositioning possible.) Dropout.1 % to 1. %. Possible by dc voltage range. 12 segments (both ends fixed, 11 points variable) 1 units to +1 units variable Digital Filter. to 12. seconds variable (filter OFF at.) Relative Humidity (DCP32 only) Dry Bulb (1Ÿ57' 2 C to 2 C [ 3 F to 9 F] Wet Bulb (1Ÿ57' 5 % to 1 % RH* External Switch (RSW Input) *From C to 1 C (32 F to 212 F) Number of Inputs Types of Connectable Outputs Terminal Voltage (open) Terminal Current (short-circuit) Allowable Contact Resistance (dry contact) Residual Current (open-collector ON) Leakage Current (open-collector OFF) 12 maximum (4 standard and 8 optional) Dry contacts (relay contact) and open-collector (current sink to ground) 1.4 V to 12.6 V (under operating conditions) across common terminal (terminal 25) and each input terminal 5. ma ma across each terminal (under operating conditions) ON: 7 ŸPD[LPXPXQGHURSHUDWLQJFRQGLWLRQV OFF: 1 kÿplqlpxpxqghurshudwlqjfrqglwlrqv 3 V maximum (under operating conditions).1 ma maximum (under operating conditions) Assignments (fixed) RUN, HOLD, RESET, ADV (digital inputs 1-4) Assignments (variable) Input Sampling Cycle ON Detection Minimum Hold Time Program Number, FAST, PV start, AT, AUTO/MANUAL, G.Soak cancel, reverse/direct action (optional inputs).1 seconds.2 seconds (Program No.:.4 seconds)

6 Page 6 Specifications, continued Indication/Programmer Upper Display Lower Display Program Number Display Segment Number Display Profile Display Green 4-digit, 7-segment LED This normally displays PV values. Item codes are displayed in parameter setup. Orange 4-digit, 7-segment LED This normally displays SP values and output value. Setting values are displayed in parameter setup. Green 2-digit, 7-segment LED This normally displays program number. Green 2-digit, 7-segment LED This normally displays segment number. Item numbers are displayed in parameter setup, and alarm number is displayed when alarm occurs. 6 orange LEDs Displays program pattern rise, soak and fall tendencies. Status Displays Operation Keys Mode 24 round LEDs Modes: Display details: Battery voltage: Status: Events: 13 rubber keys RUN, HLD, MAN, PRG (green) PV, SP, OUT, TM, CYC, CH1, CH2 (green) BAT (red) (blinks at low voltage) AT, OT1, OT2, OT3 (orange) EV1, EV2, EV3, T1, T2, T3, T4, T5 (orange) Program Operation Mode READY: Ready to run program (control stop/program number selectable) RUN: Program run HOLD: Program hold FAST: Program fast-forward END: Program end Constant-Value Operation Mode AUTO: MANUAL: READY: RUN: AUTO: MANUAL: Automatic operation Manual operation (output controlled on console) Ready to run program (control stop) Program running Automatic operation Manual operation (output controlled on console)

7 Page 7 Specifications, continued Control PID Control Three Position Control Reverse/Direct Action Switching Programmer Function Auxiliary Output Proportional band (P).1 % to % Rate time (I) seconds to 36 seconds. PD control if set to. Reset time (D) seconds to 12 seconds. PI control if set to. MV limit Lower limit: 1. % to upper limit % Upper limit: Lower limit to +11. % Manual reset. % to 1. % Number of PID sets 8 sets for program operation plus 1 set for constant-value operation PID set selection Segment designation/automatic zone selection can be switched by program operation MV change limit.1 % to 1. %/.1 seconds, no limit by. Autotuning Automatic setting of PID value by limit cycle system plus Neuro and Fuzzy (2 degrees of freedom PID) and Smart systems (not possible on heat/cool channel) Position-proportional dead zone.5 % to 25. % (settable on 2G output model) Heat/cool dead zone 1. % to +5. % (settable on 3D and 5K output models) Deviation lower/upper limit, Deviation lower/upper limit hysteresis units to 1 units (settable when 3-position control is selected on 3D output models) Switchable (output other than heat/cool) Switching: mv output can be switched to SP output (current output) Scaling: Supported Output resolution: 1/1 Type: PV, SP, deviation, MV, MFB Scaling: Supported Output resolution: 1/1 Output D Output 1 3D Outputs 1, 2, 3 Relay contact output Contact type: 1a1b Contact rating: 5A (3 Vdc, resistive load) 5A (12 Vac, resistive load) 4A (24 Vac, resistive load) Allowable contact voltage: 25 Vac, resistive load 125 Vdc, resistive load Maximum switching power: 15 W, resistive load 96 VA, resistive load Life: 1, operations (resistive load at contact rating, frequency: 3 operations/minute) Minimum switching voltage: 5 V Minimum switching current: 1 ma Output resolution: 1/1 Time-proportional cycle: 5 seconds to 12 seconds

8 Page 8 Specifications, continued Output, continued 2G Output 1 5G Outputs 1, 2 5K Outputs 1, 2, 3 Auxiliary Outputs 1, 2 5G Outputs 1, 2 5K Outputs 1, 2, 3 (when current output is switched to voltage output) M/M drive relay Contact type: 1a (2 circuits) Contact rating: 2.5A (3 Vdc, L/R =.7 ms) 4A (12 Vac, cosø =.4) 2A (24 Vac, cosø =.4) Allowable contact voltage: 25 Vac, cosø = Vdc, L/R =.7 ms Maximum switching power: 75W (L/R =.7 ms) 48 VA (cosø =.4) Life: 1, operations (cosø =.4 at contact rating, frequency: 3 operations/minute) Minimum switching voltage: 5 V Minimum switching current: 1 ma MFB (motor feedback) input range: 1 ŸWRŸ Control at MFB disconnection: ON/OFF for continuation of operation according to MFB estimated position can be selected Current output Output current: 4 to 2 ma dc / to 2 ma dc Allowable load resistance: 6 ŸPD[LPXPXQGHURSHUDWLQJFRQGLWLRQV Output accuracy: ±.1 % FS maximum (under standard conditions) Note that output accuracy becomes ±.5 % FS when to 2 ma output is 5 % or less. Output resolution: 1/1 Inrush current: 25 ma maximum for 5 ms maximum (at 25ŸORDG Maximum output current: 22. ma dc Minimum output current:. ma dc Output updating cycle:.1 seconds Open terminal voltage: 25 V maximum (output 1) 18 V maximum (output 2, output 3, auxiliary output) Voltage output Allowable load resistance: 6 ŸPD[LPXPXQGHURSHUDWLQJFRQGLWLRQV Inrush current: 25 ma maximum for 5 ms maximum (at 25 ŸORDG Load current adjustment: 2 ma to 22 ma variable Open terminal voltage: 25 V maximum (output 1) 18 V maximum (output 2, output 3) OFF leakage current: 1 $PD[LPXP Output response time: At ON-OFF 6ŸORDGPVPD[LPXP At OFF-ON 6ŸORDGPVPD[Lmum Output resolution: 1/1 Time-proportional cycle: 1 second to 6 seconds variable Event/Time Event Output Events 1, 2 Event 3 Time Events 1 to 5 Relay contact output Contact type: Contact rating: Life: Minimum switching voltage, current: Relay contact output Contact type: Contact rating: Life: Minimum switching voltage, current: Open-collector output External supply voltage: Maximum load current: OFF leakage current: ON residual voltage: 1a 1A (24 Vac/3 Vdc, resistive load) 1, operations (at rating) 1 V, 1 ma 1a1b 2 A (24 Vac/3 Vdc, resistive load) 1, operations (at rating) 1 V, 1 ma 1 to 29 Vdc 7 ma/load.1 ma maximum 1.6 V maximum

9 Page 9 Specifications, continued Event/Time Event Output, continued Event 1 to 3 Settings Event type PV type events: Controller status events: PV, deviation, absolute value deviation, SP, MV, MFB RUN+HOLD+FAST+END, READY, RUN, HOLD, FAST, END, G.Soak standby, MANUAL, autotuning executing, constant-value operation, MFB estimated position control, sum of all alarms, PV range alarm, controller alarms, low battery voltage, setting on console, ADV Time events Event standby ON/OFF selectable Event hysteresis units to 2 units (event types PV, deviation, absolute value deviation or SP). % to 2. % (event types MV or MFB) Event ON delay seconds to 36 seconds Time Event 1 to 5 Settings Time event type: Time events, segment number events General Specifications Memory Backup Memory: Battery backed-up RAM Battery life: Controller power OFF Approximately 3 years under standard conditions Controller power ON Approximately 1 years under standard conditions Rated Power Voltage Power Consumption Power ON Rush Current 9 Vac to 264 Vac, 5/6 Hz 3 VA maximum 15 A maximum, 1 ms (under operating conditions) VOLTAGE DROP CAUTION When starting up a number of DCP3s simultaneously, ensure ample power is supplied or stagger startup times. The controllers may not start normally due to inrush current induced-voltage drop. Voltage must stabilize within two seconds after power ON. Power ON Operation Allowable Transient Power Loss Insulation Resistance Dielectric Strength Reset time: 15 seconds maximum (time until normal operation possible under normal operating conditions) 2 ms maximum (under operating conditions) LQLPXP DFURVVSRZHUWHUPLQDOVRUDQGJURXQGWHUPLQDOXVLQJDVdc megger) 15 Vac 5/6 Hz for 1 minute across power terminal and ground terminal 15 Vac 5/6 Hz for 1 minute across relay output and ground terminal 5 Vac 5/6 Hz for 1 minute across non-power terminal and ground terminal 5 Vac 5/6 Hz for 1 minute across isolated terminals

10 Page 1 Specifications, continued General Specifications, continued Standard Conditions Ambient temperature: 23 C ± 2 C Ambient humidity: 6 % ± 5 % RH Rated power voltage: 15 Vac ± 1 % Power frequency: 5 Hz ± 1 Hz or 6 Hz ± 1 Hz Vibration resistance: m/s 2 Impact resistance: m/s 2 Mounting angle: Reference plane (vertical) ± 3 Operating Conditions Installation Types Applicable Standards Installation Category Ambient temperature range: C to 5 C (temperature at case bottom when closely mounted) Ambient humidity range: 1 % to 9 % RH (no condensation) Rated power voltage: 9 Vac to 264 Vac Power frequency: 5 Hz ± 2 Hz or 6 Hz ± 2 Hz Vibration resistance: m/s 2 to 1.96 m/s 2 Impact resistance: m/s 2 to 9.8 m/s 2 Mounting angle: Reference plane (vertical) ± 1 Permanent connection type unit, indoor mounting, panel mounting EN611-1, EN581-2, EN582-2 (CE Marking declaration) Category II (IEC664-1, EN611-1) Pollution Degree 2 Fuse Rating: IEC127 Cutoff speed: Delayed operation type (T) Rated voltage: 25 V Rated current: 1 A Transport/Storage Conditions Terminal Screw Terminal Screws Tightening Torque Mask/Case Materials Mask/Case Color Installation Weight Ambient temperature: 2 C to +7 C Ambient humidity: 1 % to +95 % RH (no condensation) Vibration resistance: m/s 2 to 4.9 m/s 2 (1 Hz to 6 Hz for 2 hours each in X, Y and Z directions) Impact resistance: m/s 2 to 49 m/s 2 (3 times vertically) Package drop test: Drop height: 6 cm (1 corner, 3 edges and 6 planes; free fall) M3.5 self-tapping screw.78 N m to.98 N m (6.9 in lb to 8.6 in lb) Mask: Multilon Case: Polycarbonate Mask: Dark gray (Munsell 5Y3.5/1) Case: Light gray (Munsell 2.5Y7.5/1) Specially designed mounting bracket Approximately 9 g

11 Page 11 TABLE 1 Input 1 Types and Ranges (selectable in setup) Type Thermocouple Resistance Temperature Detector (RTD) Input Type Range No. Code Temperature Range C F K (CA) K9 to 12 to 24 K (CA) 1 K8. to 8. to 16 K (CA) 2 K4. to 4. to 75 K (CA) 3 K29 2 to to +12 K(CA) 4 K44 2. to to +7 K (CA) 5 K46 2. to to +4 E (CRC) 6 E8. to 8. to 18 J (IC) 7 J8. to 8. to 16 T (CC) 8 T44 2. to to +7 B (PR3-6) 9 B18 to 18 to 33 R (PR13) 1 R16 to 16 to 31 S (PR1) 11 S16 to 16 to 31 W (WRe5-26) 12 W23 to 23 to 42 W (WRe5-26) 13 W14 to 14 to 2552 PR D19 to 19 to 34 Ni-Ni-Mo 15 Z13 to to 2372 N 16 U13 to to 2372 PL II 17 Y13 to to 2372 DIN U 18 Z8 2. to to +75 DIN L 19 Z7 2. to to +16 Golden-iron-chromel 2 Z6. to 3.K JIS'89 Pt1 (IEC Pt1 Ÿ JIS'89 JPt1 32 F5 2. to to F46 2. to to F32 1. to to F36 5. to to F38 6. to to F33 4. to to F5. to 5.. to F3. to 3.. to 5. 4 F1. to 1.. to P5 2. to to P46 2. to to +4 5 P32 1. to to P36 5. to to P38 6. to to P33 4. to to P5. to 5.. to P3. to 3.. to P1. to 1.. to 2.

12 Page 12 Type DC Current DC Voltage Input Type Range No. Code 4 ma to 2 ma 64 C1 ma to 2 ma 65 C8 mv to 1 mv 66 M1 1 mv to +1 mv 67 L2 mv to 1 mv 68 L1 V to 1 V 69 L4 1 V to +1 V 7 L8 1 V to 5 V 71 V1 V to 5 V 72 L5 V to 1 V 73 L7 Range (Programmable) 1999 to TABLE 2 Input 2 (DCP32 only) Types and Ranges (selectable in setup) Type Thermocouple Resistance Temperature Detector (RTD) Type DC Voltage Input Type Range No. Code Temperature Range C F K (CA) 128 K44 2. to to +7 K (CA) 129 K29 2 to to +24 JIS'89 PT1 16 F36 5. to to +4. (IEC Pt1 Ÿ 161 F1. to 1.. to 2. JIS'89 JPt1 Input Type 176 P36 5. to to P1. to 1.. to 2. Range No. Code V to 1 V 192 L7 1 V to 5 V 193 V1 Range (Programmable) 1999 to NOTES FOR TABLE 1 AND TABLE 2: n Readout Accuracy (items outside of ±.1 % FS range) At 1 C maximum of K and T thermocouples: ± 1 C ± 1 unit At 26 C maximum of B thermocouple: ± 4 % FS ± 1 unit At 26 C to 8 C: ±.4 % FS ± 1 unit At 8 C to 18 C: ±.2 % FS ± 1 unit At 1 C maximum of R and S thermocouples: ±.2 % FS ± 1 unit At 1 C to 16 C: ±.15 % FS ± 1 unit At 3 C maximum of PR4-2 thermocouple: ± 2.5 % FS ± 1 unit At 3 C to 8 C: ± 1.5 % FS ± 1 unit At 8 C to 19 C: ±.5 % FS ± 1 unit Golden iron chromel thermocouple: ± 1.5 % K ± 1 unit 2-digit range past decimal point by RTD input: ±.15 % FS ± 1 unit At mv to 1 mv range: ±.15 % FS ± 1 unit At 1 C maximum of DIN U thermocouple: ± 2 C ± 1 unit At 1 C to C: ± 1 C ± 1 unit At 1 C maximum of DIN L thermocouple: ± 1.5 C ± 1 unit n The unit of code Z6 is Kelvin (K). The lower limit readout of code B18 is 2 C (68 F). The lower limit readout ( C) of codes K44, K46, T44, Z8, and Z7 is C. The lower limit readout ( C) of codes F5, F46, P5, and P46 is C. The upper limit readout ( C) of codes F1 and P1 is C. The PV lower limit alarm does not occur with code F5. n The number of digits past the decimal point for dc current and dc voltage is programmable within the range to 3. n The readout accuracy of M1 is ±.15 % FS ± 1 unit

13 Page 13 Dimensions PANEL CUTOUT (N-1) x min min N x 96 _ 4 (N: number of mounted units) min min. Using the soft dust-proof cover set Using the hard dust-proof cover set Close horizontal mounting

14 Page 14 Wiring Add-on terminal

15 Page 15 Model Selection Guide Refer to Model Selection Guide Instructions Select the desired Key Number. The arrow to the right marks the selection available. Make one selection each from Table I thru VI, using the column below proper arrow. A dot ( ) denotes unrestricted availability. A letter denotes restricted availability. Key Number I II III IV V VI - - _ KEY NUMBER Selection Availability Description 1 Channel Digital Controller/Programmer P31 2 Channel Digital Controller/Programmer P32 TABLE I Outputs Channel 1 Channel 2 (P32 Only) Relay (5 Amp) Current D Position Proportional Current 2G Current (4-2 ma) Current 5G Relay/Relay (Heat/Cool) Current 3D Current/Current (Heat/Cool) Current 5K TABLE II Inputs One Input Channel Two Input Channels 1 Temperature/Relative Humidity Calculation 2 TABLE III Power Universal Power - 9 to 264 VAC, 5/6 Hz ES TABLE IV Option 1 None 1 Auxiliary Output 1 a 2 Auxiliary Outputs 2 a TABLE V Option 2 4 Digital Inputs + 3 Events - (Standard features) 12 Digital Inputs + 3 Events + 5 Time Events 1 TABLE VI None RESTRICTIONS/NOTES Restriction Not Available With Available Only With Letter Table Selection Table Selection a I 2G, 3D, 5K I D, 5G

16 Page 16 Warranty/Remedy Honeywell warrants goods of its manufacture as being free of defective materials and faulty workmanship. Contact your local sales office for warranty information. If warranted goods are returned to Honeywell during the period of coverage, Honeywell will repair or replace without charge those items it finds defective. The foregoing is Buyer s sole remedy and is in lieu of all other warranties, expressed or implied, including those of merchantability and fitness for a particular purpose. Specifications may change without notice. The information we supply is believed to be accurate and reliable as of this printing. However, we assume no responsibility for its use. While we provide application assistance personally, through our literature and the Honeywell web site, it is up to the customer to determine the suitability of the product in the application. Distributor : For more information, contact Honeywell sales at Sensing and Control Honeywell 11 West Spring Street Freeport, IL Printed in USA