General Specifications

Transcription

1 General Specifications Terminal Boards (for IO) GS 33J0H0-01EN GENERAL This document describes the specifications of terminal boards used for IOs of CENTUM VP systems. STANDARD SPECIICATIONS [Release ] Points Terminals AEA3D AEA4D AET4D AEDD AE9D AER4D MRT(*2) or 2-wire Transmitter or analog signals or thermocouple or digital signals or fieldbus or resistance temperature detectors or resistance temperature detectors 8 pts x 4 M4 screws 8 pts x 2 M4 screws 1 pts x 2 M4 screws Modules Connected AAI13 AAI83 AAP13 AAI13 AAI83 AAP13 AAI141 AAV141 AAV142 AAV144 AAB841 AAI841 AAV42 AAV44 AAI143 AAI43 Connection Cable KS1 KS1 1 pts x 2 M4 screws AAT14 KS1 32 pts x 1 M4 screws ADV11 ADV1 ADV11 (*1) ADV1 (*1) AKB331 AKB337 4 ports x 4 M4 screws AL111 AKB33 1 pts M4 screws AAR14 AKB33 1 pts x 2 M4 screws AAR14 KS8 Weight 1. kg 1. kg 1. kg Specifications Insulation resistance: 100 MΩ or greater at 00 V DC Withstanding voltage: 00 V AC for 1 minute Insulation resistance: 100 MΩ or greater at 00 V DC AEC4D or digital signals 1 pts x 2 M4 screws ADV141 ADV142 ADR41 AKB332 AKB333 AKB334 Withstanding voltage: Between commons; 100 V AC for 1 minute, common minus side every 8-channel Between signal and case; 2300 V AC for 1 minute Note: Be sure to leave the connector caps on connectors that are not used, in order to protect the connector pins and prevent dust from accumulating on them. *1: Two sets of AEDD or AKB337 are required for one set of ADV11 or ADV1. *2: or details on the MRT, see GS 33KR40-0E. Yokogawa Electric Corporation , Nakacho, Musashino-shi, Tokyo, Japan Tel.: ax.: GS 33J0H0-01EN Copyright eb. 201 (YK) 2nd Edition Mar. 17, 201 (YK)

2 2 EXTERNAL DIMENSIONS Terminal Boards AEA3D (8) (4 M screw holes) 01E.ai When the reference dimension is over 0. mm and equal or less than 120 mm, its nominal tolerance is ± 0.8 mm, while its combination of nominal tolerance is ± 1. mm. When the reference dimension is over 120 mm, its nominal tolerance is in accordance with JEM 149. AEA4D, AET4D (8) (2 M screw holes) 02E.ai When the reference dimension is over 0. mm and equal or less than 120 mm, its nominal tolerance is ± 0.8 mm, while its combination of nominal tolerance is ± 1. mm. When the reference dimension is over 120 mm, its nominal tolerance is in accordance with JEM 149. All Rights Reserved. Copyright 201, Yokogawa Electric Corporation GS 33J0H0-01EN eb. 1,

3 3 AEDD (8) (2 M screw holes) 03E.ai When the reference dimension is over 0. mm and equal or less than 120 mm, its nominal tolerance is ± 0.8 mm, while its combination of nominal tolerance is ± 1. mm. When the reference dimension is over 120 mm, its nominal tolerance is in accordance with JEM 149. AEC4D (8) (4 M screw holes) 04E.ai When the reference dimension is over 0. mm and equal or less than 120 mm, its nominal tolerance is ± 0.8 mm, while its combination of nominal tolerance is ± 1. mm. When the reference dimension is over 120 mm, its nominal tolerance is in accordance with JEM 149. All Rights Reserved. Copyright 201, Yokogawa Electric Corporation GS 33J0H0-01EN eb. 1,

4 4 AER4D (8) (2 M screw holes) 0E.ai When the reference dimension is over 0. mm and equal or less than 120 mm, its nominal tolerance is ± 0.8 mm, while its combination of nominal tolerance is ± 1. mm. When the reference dimension is over 120 mm, its nominal tolerance is in accordance with JEM 149. AE9D (8) (4 M screw holes) 0E.ai When the reference dimension is over 0. mm and equal or less than 120 mm, its nominal tolerance is ± 0.8 mm, while its combination of nominal tolerance is ± 1. mm. When the reference dimension is over 120 mm, its nominal tolerance is in accordance with JEM 149. All Rights Reserved. Copyright 201, Yokogawa Electric Corporation GS 33J0H0-01EN eb. 1,

5 MODELS AND SUIX CODES AEA3D (single and dual-redundant, 8-channel) E Basic type with AEA4D (single and dual-redundant, 1-channel) E Basic type with Terminal Board for Thermocouple Terminal Board for Thermocouple AET4D (single and dual-redundant, 1-channel) E Basic type with Terminal Board for Digital (single and dual-redundant) Terminal Board for Digital AEDD (single and dual-redundant, 32-channel) E Basic type with Terminal Board for Digital Terminal Board for Digital (single and AEC4D dual-redundant, 1-channel) - or 100 V V AC input - or 220 V V AC input -7 or Relay output Basic type with E (*1) (*1) *1: These suffix codes cannot be specified with AEC4D-. Terminal Board for Resistance Temperature Detectors Terminal Board for resistance temperaure detectors AER4D (single and dual-redundant, 1-channel) E Basic type with Terminal Board for ieldbus Terminal Board for ieldbus AE9D E Basic type with Note: When the AEDD is used in voltage output mode, it does not conform to Non-Incendive standard. All Rights Reserved. Copyright 201, Yokogawa Electric Corporation GS 33J0H0-01EN eb. 1,

6 APPLICABLE STANDARDS Refer to the GS "Integrated Production Control System CENTUM VP System Overview (GS 33J01A10-01EN)." ORDERING INORMATION Specify models and suffix codes when ordering. or selecting the right products for, please refer to TI 33Q01J30-01E without fail. TRADEMARK CENTUM is a registered trademark of Yokogawa Electric Corporation. Other company names and product names in this document are registered trademarks or trademarks of their respective holders. All Rights Reserved. Copyright 201, Yokogawa Electric Corporation Subject to change without notice. GS 33J0H0-01EN Mar. 17,