ANALOG INPUT/OUTPUT MODULES SPECIFICATIONS* Input resistance. From ± 10 mveff to ± 50 Veff (see ranges) AC input ZIN = 100 KΩ
|
|
- Cory Walker
- 6 years ago
- Views:
Transcription
1 ACM ANALOG INPUT/OUTPUT MODULES Analog Input/Output: - Modules - Voltage - Potentiometer - Current - RTDs and thermocouples - Strain gage - Accelerometer - ICP Freq => Voltage - RMS => DC - Etc. Plug and Play Easy identification with eight colours High accuracy ± 0,03 % FS typical Insulation 500 Vrms Protected Input/Output Narrow and wide band Fault detection High reliability Very low cost ACM series was developed to answer in a simple way to any type of sensors' conditioning. Simplicity of use is not to the detriment of measure quality because ACM modules integrates: - Galvanic insulation up to 500 Vrms - Inputs and Outputs protections - Metrological characteristics of class > 12 bits - 4th order low-pass filters - A defect output in case of abnormality on the signal ACM modules are presented in eight colors with a clear identification to facilitate their maintenance. ACM modules are mounted on a STB6x2 for a module 8 and a STB658 to form 16 conditioned inputs or outputs. Furthermore, ACM modules are very cost attractive. SPECIFICATIONS* INPUT MODULES DC VOLTAGE VERSION Input range Input protection Input resistance Linearity From 50 mv to 50 V FS (see ordering information) ± 100 V DC 1 MΩ ± 0,1% FS ± 0,03% FS RMS/DC MODULES (FIN = 1 KHZ) SINUS Input range Coupling Bandwidth From ± 10 mveff to ± 50 Veff (see ranges) AC input ZIN = 100 KΩ 40 Hz to 20 KHz (± 1 db) ± 0,2 % FS (FS to FS/20) APPLICATIONS Linearity Crest factor CURRENT VERSION ± 0,05 % FS (FS to FS/20) 3 max Input resistor input protection 0 20 ma ; 4 20 ma ; 0 40 ma ± 2 ma; ± 5 ma; ± 8 ma ; ± 10 ma ; ± 20 ma ; ± 40 ma 50 Ω 24 V max CONTACT: mail@adas.fr Tel.:
2 ACM - ANALOG INPUT/OUTPUT MODULES INPUT MODULES (MORE) THERMOCOUPLE VERSION s J, K, T, E, R, S Cold junction compensation t = 25 C : ± 2 C Compensation error Δ t = 10 C to 40 C : ± 1,5 C Warn up time 10 mn Open-loop detection Yes PLATINIUM SENSOR VERSION (RTD) 3 and 4 wires Injected current 1 ma Linearization (PT100) Yes α 1 = STRAIN GAGE SPECIFICATIONS Wiring Bridge Supply bridge 10,000 V / 30 ma Sensibility 10 mv / V Gain 100 ACCELERO ICP Supply Constant current 4 ma / 24 V Coupling AC Fc (LPF) = 0,1 Hz VIN ± 5 V FS FILTERING Low-pass Butterworth 4th order polynomial filter Cutoff frequency To be defined at order (refer to table) ANALOG OUTPUT TO THE SYSTEM Voltage ± 10 V FS Output impedance < 10 Ω Max. current 5 ma ± 0,03 % typ. FS (± 0,06 min) Stability 20 ppm/ C OUTPUT MODULES VOLTAGE VERSION Levels Output drive Output resistance 0 5 V ; 0 10 V ± 5 V ; ± 10 V 20 ma max 0,5 Ω CURRENT VERSION Levels Output compliance voltage 0 20 ma ; 4 20 ma; ± 20 ma ± 10 V min OTHER Linearity Noise Bandwidth Output setting time Stability Output enable control Output protection ±0,05 % span ±0,03 % span 20 μa p-p 3 KHz (- 3dB) 100 μs 20 ppm/ C Security 0 V or 0 ma Continuous short to ground WWW. ADAS.FR
3 ACM - ANALOG INPUT/OUTPUT MODULES COMMON SPECIFICATIONS ISOLATION I/O Rated IMR High- voltage breakdown 500 Vrms 140 db at 60 Kz LOGIC OUTPUTS Function Output Detection of out-of-range or loop error condition open collector, TTL compatible POWER SUPPLY Consumption 0,5 W typ. 1 W max PHYSICAL CHARACTERISTICS Size (H x W x D) Mounting 55 x 50 x 17 mm DB 25 TYPE ENVIRONMENT Operating temperature - 10 C to + 70 C Storage temperature - 20 C to + 85 C Relative humidity 90 % non condensing EUROPEAN STANDARDS CE Compliance (EMC - EN EN Class A) ROHS /95/EC ACCESSORIES: SHUNT R = 0,00. Ω ou R = 0,1 Ω (1% ; 50ppm / C) CURRENT TRANSDUCER SPECIFICATIONS ACCESSORY ORDER: STB/SHUNT/0.XX ** 10 = 10 A 20 = 20 A 50 = 50 A STB/LA55P/** WWW. ADAS.FR
4 COMMENT COMMANDER MODULE D'ENTREE? ACM /IN *** OU ACM/IN***/RMS FREQUENCE DE COUPURE STANDARD FREQUENCE DE COUPURE SPECIALE F1 = 10Hz F3 = 100Hz F5 = 1KHz F6 = 5KHz F7 = 10KHz F8 = 20KHz TENSION DC TENSION AC BOUCLE COURANT COURANT MOYEN COURANT ELEVE BIPOLAIRE RMS VB = ± 50V VF ± 200V BA = 0/20mA R = 50Ω VA = ± 20V VD ± 150V (0mA = -10V / 20 ma = + 10V) 10 10A V0 = ± 10V VC ± 100V BB = 4/20mA R = 50Ω 20 20A V1 = ± 5V VB = ± 50V (4mA = -10V / 20 ma = + 10V) 50 50A V2 = ± 2V VA = ± 20V BC = ± 20mA R = 50 Ω STB/DERIVATION (0,01Ω) STB/LA55P/** V3 = ± 1V V0 = ± 10V ( ± 20mA 10V) + + V1 = ± 5V BD = 4/20mA R = 50Ω module module V2 = ± 2V (4mA = 0V / 20mA = 10V) V3 = ± 1V BE = 0 / 40mA R = 25Ω DC DC V4 = ± 500mV (0mA = -10V ; 40mA = +10V) ACM/IN/V6 = ± 10A dc ACM/IN/LA55P/DC V5 = ± 200mV BF = ± 8mA R = 50Ω ACM/INV9 = ± 1A dc V6 = ± 100mV Ex : ACM/INV0/RMS ( ± 8mA ±10V) AC BG = ± 5mA ACM/INV6/RMS = ± 10A eff AC V7 = ± 50mV ( ± 5mA ±10V) ACM/INV9/RMS = ± 1A eff ACM/IN/LA55P/RMS V8 = ± 20mV Ex : ACM/INBC BP : 40Hz à 20KHz V9 = ± 10mV Ex : ACM/INV4 STB/DERIVATION (0,1Ω) DC ACM/IN/V6 = ± 1A dc POTENTIOMETRE RESISTANCE (4 fils) ACM/INV9 = ± 100mA dc VALIM POT = 5,00V Référence PE INJ AC P0 = 0 5V R13 1KΩ 100µA ACM/INV6/RMS = ± 1A eff P1 = 0 10V R14 10KΩ 10µA ACM/INV9/RMS = ± 100A eff R15 100KΩ 10µA Ex : ACM/INP0 Ex : ACM/IN R1X
5 COMMENT COMMANDER MODULE D'ENTREE? ACM /IN *** THERMOCOUPLES ( C) SONDE PLATINIUM PONT DE JAUGE FONCTIONS SPECIALES TYPE J TYPE K A31 ou A41 = - 50 / C A32 ou A42 Ex: ACM/ SG350 Ω Ex:ACM/INLM35 J2 = / k3 = / IN: +/- 100mV -50 / C J1 = / k2 = / B31 ou B41 = - 50 / C ALP: 10V ; Fc: 1 KHz ACM/INMPX5100 J0 = / k1 = / B32 ou B42 Silicium intégré k0 = / Capteur de pression C31 ou C41 = - 50 / C Frescale MPX5100 series TYPE T TYPE E C32 ou C42 T1 = / E2 = / D31 ou D41 = - 50 / C T0 = / E1 = / D32 ou D42 E0 = / L31 ou L41 = - 50 / + 50 C TYPE R TYPE S L32 ou L42 1 = α = 0,385 3 = 3 fils R1 = / S1 = / = α = 0,392 4 = 4 fils R0 = / S0 = / Ex. : ACM/INB41 Ex. : ACM/INE2 FREQUENCE COUPURE STANDARD Notes : F1 = 10Hz F3 = 100Hz F5 = 1KHz Les plages thermocouples données ci-dessus sont en valeurs positives PE. C'est aussi possible en valeurs négatives. Ex : K = - 6,458mV = C
6 COMMENT COMMANDER MODULE DE SORTIE? ACM/OUT ** ACM/OUT **- I Haute tension mode commun Version isolement galvanique TENSION COURANT VIN = ± 10V VB = ± 40V VA = ± 20V V0 = ± 10V V1 = ± 5V BA BB BC BD = 0/20mA RLm = 500Ω (- 10V = 0mA ; + 10V = 20mA) = 4/20mA RLm = 500Ω (- 10V = 4mA ; + 10V = 20mA) = ± 20mA RLm = 500Ω (-10V = - 20mA ; +10V = 20mA) = 4/20mA RLm = 500Ω (0V = 4mA ; 10V = 20mA) WB = WIDE BAND BE = 0 / 40mA RLm = 200Ω (-10V = 0mA ; +10V = 40mA) Ex : ACM/OUTVA-WB BF = ± 8mA RLm = 1000Ω ( -10V = - 8mA ; 10V = 8mA) Ex : ACM/OUTBC NB : RLm = R Loop max
DOCUMENTATION. The new XALIS 9000 integrates a 32 bits microprocessor offering some more of performance.
DOCUMENTATION The new integrates a 32 bits microprocessor offering some more of performance. XALIS is a new digital indicator range with 2 colors numerical and alphanumerical display designed to provide
More informationModule Input type Ranges TEDS Filters (LP = lowpass, HP = highpass) Piezoresistive bridge ±0.5 to mv/ma 1 ma exc
HSI Series Modules Selection Guide HSI Series Modules Single channel High bandwidth - for dynamic signals Isolation (all models Analog signal output (±5 V Single channel modularity For DEWETRON systems
More informationDRG-SC Series Signal Conditioners
DRG-SC Series Signal Conditioners DRG-SC Series 245 Basic unit Models Available for Thermocouples, RTDs, DC Voltage and Current, Frequency, Strain Gage Bridge, AC Voltage and Current Field Configurable
More informationAdvanced Test Equipment Rentals ATEC (2832)
Established 1981 Advanced Test Equipment Rentals www.atecorp.com 800-404-ATEC (2832) TEST & MEASUREMENT PRODUCT GROUP 600 East Greenwich Avenue West Warwick, RI 02893 Phone: 401-828-4000 Fax: 401-822-2430
More informationIsolated Linearized 4-Wire RTD Input 5B35 FEATURES APPLICATIONS PRODUCT OVERVIEW FUNCTIONAL BLOCK DIAGRAM
Isolated Linearized 4-Wire RTD Input 5B35 FEATURES Single-channel signal conditioning module that Amplifies, Protects, Filters, and Isolates Analog Input. Isolates and protects a wide variety of four-wire
More informationSDM3045X Digital Multimeter. DataSheet
SDM3045X Digital Multimeter DataSheet-2016.06 User-friendly Design Product Overview SDM3045X is a 4½ digit digital (60000 count) multimeter incorporating a dual-display and is especially well suited for
More informationEconomical Digital Indicators For Process and Electrical Measurement
Economical Digital Indicators For Process and Electrical Measurement DP18 Series Panel Punches Available DP18-P5, 4 to 20 ma input. DP18-EC, thermocouple input visit omega.com/thermocouple for thermocouples.
More informationUSB-2404-UI Specifications
Specifications Document Revision 1.1, April, 2011 Copyright 2011, Measurement Computing Corporation All specifications are subject to change without notice. Typical for the range 0 to 60 C unless otherwise
More informationCONTA-ELECTRONICS. Converter Units
CONTA-ELECTRONICS Whether for manufacturing, electrical machine and plant instrumentation, control engineering, power distribution, building automation, or process engineering it is always important to
More informationS200 I/O System Units
S200 I/O System Units S200 I/O is a range of cost effective I/O units which are bus compatible with S200L I/O and can be mixed with them in any order on the same DIN rail. The S200 I/O System features
More informationProcess displays For standard signals, temperature, resistance measurement
Features Inputs: Voltage ±10 V, ±200 V / Current ±20 ma / thermocouples J,K,T,N,Pt100,Pt1000 / resistance measurement / potentiometer Display range can be linearised Two limits output Min, Max functions
More informationCALYS Transportable documenting multifunction calibrator with high accuracy 0.01%
Transportable documenting multifunction calibrator with high accuracy 0.01% CALYS 1200 is the ideal solution to simultaneously simulate and measure with a high accuracy of 0.01%: voltage, current, resistance,
More informationSHIMADEN DIGITAL INDICATORS
Shimaden, Temperature and Humidity Control Specialists C %RH Series SD16A & SHIMADEN DIGITAL INDICATORS approved,ul applied BASIC FEATURES compliance DIN Size 48 x 96 mm ±.3% High Accuracy Indication Large
More informationEX1000 Series EX1000A EX1000A-TC EX1016A EX1032A EX1048A EX10SC EX1000A-TCDC RELIABLE DATA FIRST TIME EVERY TIME.
8 3-0 0 0 1-0 0 0 1 4 A EX1000 Series EX1000A EX1000A-TC EX1016A EX1032A EX1048A EX10SC EX1000A-TCDC * SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE www.vtiinstruments.com RELIABLE DATA FIRST TIME EVERY
More informationADAM 4000/4100 Series
ADAM 4000/4100 Series Common Dimensions Communication RS-485 (2-wire) to host Speeds: 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 bps (ADAM-4080, ADAM-4080D only support up to 38400 bps) Max. communication
More informationMODEL: M6SXU MODEL: M6SXU [1][2] [3][4]
Tension-Clamp Ultra-Slim Signal Conditioners M6S Series UNIVERSAL TRANSMITTER (PC programmable) Functions & Features Maintenance-free tension clamp connection Universal input (mv, V, ma, T/C, RTD and potentiometer)
More informationDSCL, DSCP, SCTP. Industrial Loop Isolators and Transmitters DSCL, DSCP, SCTP. Industrial Loop Isolators and Transmitters
Industrial Loop Isolators and Transmitters DSCL,, SCTP DSCL,, SCTP Industrial Loop Isolators and Transmitters Description Dataforth s DSCL,, and SCTP series of products is a complete family of loop and
More informationSefram. Sefram SEFRAM A new family of thermal recorders 6 to 36 channels. Make sure to visit our Website
Make sure to visit our Website http://wwwseframfr Sefram Sefram SEFRAM A new family of thermal recorders 6 to 36 channels 6 to 36 analogue channels Measurement boards : - 6 isolated channels universal
More informationSEFRAM DAS Sefram. Sefram. A new family of paperless recorders 6 to 72 channels, to cover all your applications
Sefram SEFRAM Make sure to visit our Website http://wwwseframfr A new family of paperless recorders 6 to 72 channels, to cover all your applications 6 to 72 analogue channels Measurement boards : - 6 isolated
More informationIsolated, Linearized Thermocouple Input 7B47 FEATURES APPLICATIONS PRODUCT OVERVIEW FUNCTIONAL BLOCK DIAGRAM
Isolated, Linearized Thermocouple Input 7B47 FEATURES Interfaces, amplifies and filters input voltages from a J, K, T, E, R, S, B or N-type thermocouple. Module provides a precision output of either +1
More informationIsolated, Thermocouple Input 7B37 FEATURES APPLICATIONS PRODUCT OVERVIEW FUNCTIONAL BLOCK DIAGRAM
Isolated, Thermocouple Input 7B37 FEATURES Interfaces, amplifies, and filters input voltages from a J, K, T, E, R, S, or B-type thermocouple. Module provides a precision output of either +1 V to +5 V or
More informationModular Smart Interfaces
Modular Smart Interfaces Automotive Energy & Power Analysis Aerospace & Defense Transportation General Test & Measurement Modular Smart Interfaces MSI Series Modular Smart Interfaces (MSI) bring an expanded
More informationimc CANSAS-L-HCI8. High isolated module for the capture of temperature, voltage, current (20 ma) and resistance
Data Sheet Version 1.9 imc CANSAS-L-HCI8 High isolated module for the capture of temperature, voltage, current (20 ma) and resistance The imc CANSAS module (CANSAS-L-HCI8) enable measurement of low voltage
More informationSHIMADEN DIGITAL INDICATORS
Shimaden, Temperature and Humidity Control Specialists C %RH Series SD16 & SHIMADEN DIGITAL INDICATORS & NRTL /C approved BASIC FEATURES DIN Size 48 x 96 mm ±.3% High Accuracy Indication Large 2 mm bright
More informationP5201 Universal Programmable Transmitters with Galvanic Isolation
Transmitters - KB0288-2012/09 P5201 Universal Programmable Transmitters with Galvanic Isolation One type of transmitter for all regular resistance and thermocouple sensors. Linearized output signal 4 to
More informationChapter 6 Specifications
Chapter 6 Specifications DC Characteristics Function Range [2] Test Current or Burden Voltage DC Voltage DC Current Resistance [6] 24 Hour [3] T CAL ±1 Accuracy Specifications: ± (% of reading + % of range)
More informationAKP-AKU DIGITAL PANEL METER
DIGITAL PANEL METER AKP-AKU Isolated digital indicators AKP and AKU are designed to provide display and signals transmission solutions. Its unique programmation principle on front plate or by digital output
More informationTel: (949) Fax: (949) IAA100 Product Manual
IAA100 Product Manual Table of Contents Default Settings... 3 Connections... 3 Standard Span & Zero Adjustment... 4 Shunt Readings... 5 Digitally Controlled Remote Shunt... 5 Switch Configurations... 6
More informationIsolation (ISO), Special Overvoltage functions protection (OP) Voltage measurement PAD-V8-P 8 Voltage, up to ±50 V BW: 6 Hz ISO: 350 V DC
Selection Guide PAD Series Modules Multi channel Low bandwidth - for static signals Isolation Digital output (RS-485) Exchangeable For DEWETRON systems with built-in DAQ rack Module # CH Input type Ranges
More informationAssembly. Front view. Parametrization interface. Power Bus
Temperature Converter Features Assembly 1-channel signal conditioner 24 V DC supply Thermocouple, RTD, potentiometer or mv input Input for PTC thermistor Current and voltage output Line fault (LFD) and
More informationSDM3045X Digital Multimeter. DataSheet
SDM3045X Digital Multimeter DataSheet-2018.12 User-friendly Design Product Overview SDM3045X is a 4½ digit digital (60000 count) multimeter incorporating a dual-display and is especially well suited for
More informationSEM210 SERIES. Programmable In-head Universal Temperature Transmitter INDEX SECTION CONTENTS PAGE NO.
INDEX SECTION CONTENTS PAGE NO. SEM210 SERIES 1.0 DESCRIPTION 1 2.0 SPECIFICATION 15 3.0 INSTALLATION 67 Programmable Inhead Universal Temperature Transmitter Status Instruments Ltd, Green Lane Business
More informationFC Series Signal Conditioners
FC Series Signal Conditioners FC-33 DC Selectable Signal Conditioner with 3-way isolation Field configurable input and output ranges of 0-5V, 0-10 V, 0-20 ma and 4-20 ma with 1500 VDC isolation between
More informationFeatures EX1629. High-performance Remote Strain Gage Measurement Unit. Overview. 48 programmable channels in a single unit
Overview The VXI Technology EX1629 Remote Strain Gage simplifies stress and fatigue testing of large mechanical structures such as airframes and launch vehicles. Ethernet control allows for remote operation
More informationCALYS 50. Field multifunction calibrator for basic use
Field multifunction calibrator for basic use CALYS 50 field multifunction calibrator is the perfect tool for advanced process maintenance and use on test bench in all industries. Suitable for all field
More informationC330 / C330X PC-Programmable Universal, 2-wire Transmitter
C330 / C330X PC-Programmable Universal, 2-wire Transmitter The IPAQ C330 transmitter is a universal, isolated, temperature transmitter with additional voltage and resistance input. Its robust design and
More informationDatasheet. SDM3065X Digital Multimeter. Product Overview. Main Feature. Application fields. Main Function
Datasheet SDM3065X Digital Multimeter Product Overview SDM3065X is a 6 ½ digit digital (2,200,000 count) multimeter incorporating a dual display and is especially well suited for the needs of high-precision,
More informationMODEL: M2XU MODEL: M2XU [1][2] [3][4]
Super-mini Signal Conditioners Mini-M Series UNIVERSAL TRANSMITTER (PC programmable) Functions & Features Accepts direct inputs from various sensors and provides a standard process signal I/O types and
More informationIsolated DIN Rail Mount Loop-Powered 2-Wire Signal Conditioners. DRLP Series
Isolated DIN Rail Mount Loop-Powered 2-Wire Signal Conditioners DRLP Series U ±0.03% Accuracy (Typical) U ±0.01% Linearity U 1500Vrms Transformer Isolation and 240Vrms Field-Side Protection U Wide Loop
More informationONEXIS AUTOMATIONS PVT LTD B-8, First Floor, Industrial Area, Sector - 64, NOIDA , U.P, India Ph:
X A L I S XALIS is a new digital indicator range with 2 colors numerical and alphanumerical display designed to provide display and signals transmission solutions. XALIS disign allows exceptional performances
More informationIsolated, Frequency Input 5B45 / 5B46 FEATURES APPLICATIONS PRODUCT OVERVIEW FUNCTIONAL BLOCK DIAGRAM
Isolated, Frequency Input 5B45 / 5B46 FEATURES Isolated Frequency Input. Amplifies, Protects, Filters, and Isolates Analog Input. Generates an output of 0 to +5V proportional to input frequency. Model
More informationIntroduction ISOLATED SIGNAL CONDITIONING can significantly increase
Introduction ISOLATD SIGNAL CONDITIONING can significantly increase your system reliability here's how: Linearizes Thermocouple and RTD signals Reduces the demands on the software to linearize the signal
More informationIsolated, Linearized RTD Input 7B34 FEATURES APPLICATIONS PRODUCT OVERVIEW FUNCTIONAL BLOCK DIAGRAM
Isolated, Linearized RTD Input 7B34 FEATURES Amplifies, Protects, Filters, and interfaces input voltages from a wide variety of two and three-wire platinum, copper and nickel Resistor Temperature Detectors
More informationEX FEATURES. Stand-alone 48-channel unit with built-in Ethernet controller. Built-in bridge completion and Excitation
data sheet EX1629-001 High-performance Remote Strain Gage Measurement Unit FEATURES Stand-alone 48-channel unit with built-in Ethernet controller Built-in bridge completion and Excitation 24-bit A/D per
More informationAnalog Isolation Amplifiers
Isolation Amplifiers Analog Isolation Amplifiers HSI/DAQ Series Modules DEWETRON high precision signal conditioning amplifiers are available for almost any sensor to measure Voltage Current Pressure Temperature
More informationSCM5B48 ACCELEROMETER INPUT MODULE USER S MANUAL
SCM5B48 ACCELEROMETER INPUT MODULE USER S MANUAL Section Description Page 1.0 Introduction 1 2.0 CE Compliance 1 3.0 Features and theory of operation 1 4.0 The High Pass filter and the Low Pass Bessel
More informationRS Pro DIGITAL MULTI-METER SDM3055 SERIES
ENGLISH Product Datasheet Stock No: 1236465 1236466 RS Pro DIGITAL MULTI-METER SDM3055 SERIES Product Overview RSDM3055 is a digital multimeter designed with 5 ½ digits readings resolution and dual-display,
More informationEthernet-Based Temperature, Voltage and Strain Measurement Modules
Ethernet-Based Temperature, Voltage and Strain Measurement Modules OMB-NET6000 Series OMB-NET6220 shown smaller than actual size. U 12 Analog Inputs U 8 Digital I/O U Simultaneous Sampling U Multiple Trigger
More informationDP2000 ORDERING GUIDE To Order MODEL NO.
1 8 DIN VERSATILE PROCESS MONITORS CONFIGURABLE DP2000-S, 1 8 DIN meter, shown smaller than actual size. DP2000 Series Complete with Input Board RoHS 2 Compliant DP2000-J1, with TJ36-ICSS-116G-12, transition
More informationQ.raxx A101-8 slimline RS / EC
The Q.raxx slimline product is based on the standardized 19 technology, one rack mount unit (1 U) and is designed for measurements with a high level of flexibility, reliability and accuracy in the field
More informationMODEL: R30US4. Remote I/O R30 Series
Remote I/O R30 Series UNIVERSAL INPUT MODULE (4 points, isolated) Functions & Features 4 points universal input I/O module Isolation between the channels Input range of each channel is individually adjustable
More informationIsolated, Linearized Thermocouple Input 5B47 FEATURES APPLICATIONS PRODUCT OVERVIEW
Isolated, Linearized Thermocouple Input 5B47 FEATURES Isolated Thermocouple Input. Amplifies, Protects, Filters, and Isolates Thermocouple Input Works with J, K, T, E, R, S, and B-type thermocouple. Generates
More informationHigh-precision process calibrator Model CED7000
Calibration technology High-precision process calibrator Model CED7000 WIKA data sheet CT 85.51 Applications Research and development laboratories Calibration service companies and service industry Industry
More informationSHIMADEN DIGITAL INDICATOR
Shimaden, Temperature and Humidity Control Specialists C %RH Series SD24 & KR16A SHIMADEN DIGITAL INDICATOR BASIC FEATURES ohigh Accuracy ±0.1% FS+1 digit o1/1000ºc Resolution Indication Possible (Pt input
More informationMODEL: M2MNV MODEL: M2MNV-[1][2]-[3][4]
MODEL: MMNV Super-mini Signal Conditioners Mini-M Series ANALOG SWITCHING MODULE Functions & Features Switches between two analog signal channels Switches/Distributes one voltage signal to two channels
More information2 WIRE - LOOP POWERED AND ISOLATED TRANSMITTER FOR TERMORESISTANCE AND THERMOCOUPLE. resistances. The RTD input may be with 2,3 or 4 wire connection.
EN T WIRE - LOOP POWERED AND ISOLATED TRANSMITTER FOR TERMORESISTANCE AND THERMOCOUPLE. GENERAL DESCRIPTION The T instrument converts and transmits the input read into a normalized signal current for..0
More informationUSB-TEMP and TC Series USB-Based Temperature Measurement Devices
USB-Based Temperature Measurement Devices Features Temperature and voltage measurement USB devices Thermocouple, RTD, thermistor, or semiconductor sensor measurements Eight analog inputs Up to ±10 V inputs*
More informationCALYS 100. Field precision documenting multifunction calibrator
Field precision documenting multifunction calibrator is a precision documenting multifunction calibrator within CALYS range. It is the perfect tool for advanced process maintenance and use on test bench
More informationFC-33, DC SELECTABLE SIGNAL CONDITIONER
FC-33, DC SELECTABLE SIGNAL CONDITIONER Description. The FC-33 is a DIN rail or side mount, selectable input/output signal conditioner with 1500VDC isolation between input and output, and 1500VDC isolation
More informationFor ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Applications.
Current Transducer IT 205-S ULTRASTAB I PN = 200 A For ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Features Wide operating temperature
More informationR24 DISPLAY MODULE WITH ACTIVE OUTPUT AND RELAY
Čapkova 22 678 01 Blansko tel.: +420 516 416942, 419995 fax: +420 516 416963 R24 DISPLAY MODULE WITH ACTIVE OUTPUT AND RELAY Display module is designed for measuring the resistance, the signal from the
More informationIsolated High Level Voltage Output 7B22 FEATURES APPLICATIONS PRODUCT OVERVIEW FUNCTIONAL BLOCK DIAGRAM
Isolated High Level Voltage Output 7B22 FEATURES Unity gain single-channel signal conditioning output module. Interfaces and filters a +10 V input signal and provides an isolated precision output of +10V.
More informationAnalog Signal Conditioning Accessories
NI 64-channel multiplexer mv, V, current, and thermocouple inputs NI 8-channel simultaneous sample-and-hold mv, V inputs NI SC-2042-RTD 8-channel RTD/thermistor RTD, thermistor, mv, V inputs NI 8-channel
More informationminimal installation depth: 70 mm without plug-in terminal 30 additional adjustable setpoints (parameter driven)
Digital panel meter 5-digit M2 red display of -19999 99999 digits (optional green, orange, blue or tricolour display) minimal installation depth: 70 mm without plug-in terminal adjustment via factory default
More informationCALYS 75. Field documenting multifunction calibrator
Field documenting multifunction calibrator is a field documenting multifunction calibrator within CALYS range. It is the perfect tool for advanced process maintenance and use on test bench in all industries.
More informationminimal installation depth: 57 mm without plug-in terminal min-/max-value recording display flashing at threshold exceedance / undershooting
Digital panel meter 4-digit M1 red display of -1999 9999 digits (optional green, orange or blue display) minimal installation depth: 57 mm without plug-in terminal adjustment via factory default or directly
More informationONE CALIBRATOR ONLY MAIN FEATURES:
ONE CALIBRATOR ONLY The MEMOCAL 2000 is a lightweight versatile, portable, hand-held calibrator developed to solve two different and coexisting customer needs: field calibration (maintenance) and laboratory
More informationBASIC FEATURES C %RH. Shimaden, Temperature and Humidity Control Specialists. CP3701: Thermocouple Temperature Converter
Shimaden, Temperature and Humidity Control Specialists C %RH CP3701: Thermocouple Temperature Converter CP3702: R.T.D. Temperature Converter CP3703: mv DC-DC Converter CP3704: V/mA DC-DC-Converter CP3705:
More informationSERIE E N. The E N series clamps use Hall-effect technology for the measurement of AC and DC currents from several milliamps to over 100 A.
Pinces Current ampèremetriques clamps for AC/DC pour current courant AC SERIE E N The E N series clamps use Hall-effect technology for the measurement of AC and DC currents from several milliamps to over
More information8588A Reference Multimeter
8588A Reference Multimeter Product Specifications March 2019 Rev. A 2019 Fluke Corporation. All rights reserved. Specifications are subject to change without notice. All product names are trademarks of
More informationQ.raxx A slimline RS / EC Universal Measurement System
Q.raxx A107-16 slimline RS / EC Universal Measurement System The Q.raxx slimline product is based on the standardised 19 technology, one rack unit (1 U) and is designed for measurements with a high level
More informationMODEL: M2MNV MODEL: M2MNV-[1][2]-[3][4]
Super-mini Signal Conditioners Mini-M Series ANALOG SWITCHING MODULE Functions & Features Switches between two analog signal channels Switches/Distributes one voltage signal to two channels CE marking
More informationSDM3055 Digital Multimeter. DataSheet
SDM3055 Digital Multimeter DataSheet-2018.06 SDM3055 SDM3055-SC Product Overview The SDM3055/SDM3055-SC is a digital multimeter designed with 5 ½ digits readings resolution and dual-display, especially
More informationFor ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Applications.
Current Transducer IT 200-S ULTRASTAB I PM = 200 A For ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Features Closed loop (compensated)
More informationCALYS 150. Advanced documenting multifunction calibrator thermometer
Advanced documenting multifunction calibrator thermometer, most advanced documenting multifunction instrument of the range, works not only as a simulator (IN / OUT) but also as a dual channel thermometer
More informationSCXI 8-Channel Isolated Analog Input Modules
SCXI 8-Channel Isolated Analog Input NI, NI SCXI-1120, NI SCXI-1120D 8 channels 333 ks/s maximum sampling rate Gain and lowpass filter settings per channel Up to 300 V rms working isolation per channel
More informationCALYS 150. Advanced documenting multifunction calibrator thermometer
Advanced documenting multifunction calibrator thermometer , most advanced documenting multifunction instrument of the range, works not only as a simulator (IN / OUT) but also as a dual channel thermometer
More informationTemperature measurement TMD 832 head transmitter
Technical information TI 062R/09/en Mat.-Nr. 510 00782 Temperature measurement TMD 832 head transmitter SMART head transmitter with HART protocol for RTD, Thermocouple and mv input signals Applications
More informationSDM3055 Digital Multimeter. DataSheet
SDM3055 Digital Multimeter DataSheet-2017.06 SDM3055 Product Overview The SDM3055 is a digital multimeter designed with 5 ½ digits readings resolution and dual-display, especially fitting to the needs
More informationQ.raxx A slimline RS / EC
The Q.raxx slimline product is based on the standardized 19 technology, one rack unit (1 U) and is designed for measurements with a high level of flexibility, reliability and accuracy in the field of stationary
More informationminimal installation depth: 25 mm without plug-in terminal min-/max-value recording display flashing at threshold exceedance / undershooting
Digital panel meter 4-digit M1 red display of -1999 9999 digits (optional green, orange or blue display) minimal installation depth: 25 mm without plug-in terminal adjustment via factory default or directly
More informationWAVESERIES Signal converters
WAVESERIES Overview WAVESERIES Signal converters Isolation and conversion of analogue signals enclosed in a rail-mounted WAVEBOX housing WAVESERIES products are well suited for users seeking an analogue
More informationDIGEM f 96 x 48 EK. Applications. Description
3-349-002-03 1/7.98 Front panel dimensions: 96 x 48 mm LED display: red or green, 14 mm high Max. display range: 19 999 to + 32 765 Modular connectors for flexible use Simple adjustments at front panel
More informationSEM104 SERIES. SEM104P Pt100 Temperature Transmitter. SEM104TC Thermocouple Temperature Transmitter INDEX SECTION CONTENTS PAGE NO.
INDEX SECTION CONTENTS PAGE NO. SEM104 SERIES SEM104P Pt100 Temperature Transmitter SEM104TC Thermocouple Temperature Transmitter SEM104P 1 1.0 DESCRIPTION 2 2.0 SPECIFICATION 2 3.0 INSTALLATION 24 4.0
More informationAnalog Modules AS-i IP20
(Figure similar) Figure Type Inputs analog 4... 20 ma / 4... 20 ma / 4... 20 ma Pt100 4 x thermocouple type J 4 x thermocouple type K Outputs analog 0... 20 ma / 0... 20 ma / -10 V... +10 V Input voltage
More informationDatasheet ACT20M Signal Isolation and Conversion NEW
Datasheet ACT0M Signal solation and Conversion NEW High quality signal isolation and conversion in a slim wide housing format is now available with Weidmuller s ACT0M range. Features include worldwide
More informationAIO and DIO PFXLM4B01DAK:Sink Output Type PFXLM401DAC:Source Output Type Virtual Resolution (pixels)
Model:PFXLM4B01DDK PFXLM4B01DDC PFXLM4B01DAK PFXLM4B01DAC LT4000M Rear module Model Name Indication PFXLM4B01 D * * (1) (2) (3) (4) Notice to our valued customers who use LT4000M series (analog model)
More informationTemperature Transmitters - Head Mounted
XTH Features - Non-programmable Models Sensor Types: Models for thermocouple Types J, K, or T Models for RTD Type Pt100 3-wire Select from a variety of pre-configured measuring ranges Internal cold junction
More informationMEMOCAL 2000/2000S. Hand-held calibrator
MEMOCAL 2000/2000S Hand-held calibrator MEMOCAL 2000 Very low temperature drift (0.1µV/ C) Accuracy: 0.015% of span Power supply: standard AA size battery (Alkaline, NiCd or Ni-MH) Measurement & generation
More informationIndustrial Interface The Signal Conditioning People
Loop Powered Products including: 420TW 420i RTD/TC-HEAD Isolating Terminal Blocks Loop Powered Isolators In-Head Transmitters DC/AC Powered Isolation including: ISOCON DUALCON SLIMCON TC-TC VCON STRAIN
More informationPFXLM4B01 D * * (1) (2) (3) (4)
Model:PFXLM4B01DDK PFXLM4B01DDC PFXLM4B01DAK PFXLM4B01DAC LT4000M Rear module Model Name Indication PFXLM4B01 D * * (1) (2) (3) (4) Notice to our valued customers who use LT4000M series (analog model)
More informationPOWER AMPLIFIERS 4 QUADRANTS 3x500 VA to 3x1500 VA - THREE-PHASES
PERFORMANCES High accuracy High stability Fast transients High inrush current facilities Wide bandwidth Very low distortion Quadrant change without transition Very low output impedance Low noise RS232
More informationC520 / C520X /C520S / C520XS HART Compatible, Universal, Dual-input 2-wire Transmitters
C520 / C520X /C520S / C520XS HART Compatible, Universal, Dual-input 2-wire Transmitters The 520 transmitters are universal, isolated, dual-input temperature transmitters with additional voltage and resistance
More informationFor ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Applications.
Current Transducer IT 605-S ULTRASTAB I PN = 600 A For ultra-high precision measurement of current: DC, AC, pulsed..., with galvanic separation between primary and secondary. Features Wide operating temperature
More informationGeneral Specifications
General Specifications GS 05F01D01E MODEL UM351 Digital Indicator with Alarms with Active Color PV Display General Model UM351 Digital Indicator with Alarms is a precision alarm instrument provided with
More informationCALYS 150. Advanced documenting multifunction calibrator thermometer
Advanced documenting multifunction calibrator thermometer , most advanced documenting multifunction instrument of the range, works not only as a simulator (IN / OUT) but also as a dual channel thermometer
More informations Climatix extension module 26 I/Os POL985.00/XXX
s 3 921 Climatix TM Climatix extension module 26 I/Os POL985.00/XXX The POL985.00/XXX extension module extends the number of I/Os of Climatix 600 controllers. It is a product of the Climatix range. The
More informationRIGOL Data Sheet DM3058/DM3058E Digital Multimeter Product Overview Applications Easy to Use Design Main Features owerful Measurement Functions
RIGOL Data Sheet Product Overview DM3058/DM3058E [1] is a digital multimeter designed with 5 ½ digits readings resolution and dual-display especially fitting to the needs of high-precision, multifunction
More informationMODEL: W2TS. Mini-MW Series
Space-saving Dual Output Signal Conditioners Mini-MW Series THERMOCOUPLE TRANSMITTER Functions & Features Accepts direct input from a thermocouple and provides a standard process signal 5-segment linearization
More informationTemperature Transmitter ZTT series
BT.11.13 ZT/I ZTT series The ZTT series transmitter accepts the most commonly used temperature sensors (RTD, T/C) as well as mv and slide wire signals. All the models adopt a 2 wire 4...20mA output signal
More information