Features. High output power Max 40W. Wide current range. Output voltage:

Transcription

1 The IZI-Drive 4ch. Constant LED driver has a versatile design and utilises hybrid dimming techniques, offering superb brightness control down to 0,0%. This high-power LED driver can drive up to 40 Watts per channel, with a current that is user selectable from to 1050mA, in 50mA steps. The LED driver allows control via an onboard IZI-Link interface and DMX-512 interface. Features High output power Max 40W Precise current selection 50mA steps Wide current range Remote configuration ~ 1050mA With IZI-Manager software Technical specifications Power Input voltage: Output voltage: Output power: Channels: per channel: Max. 4DC 4 x 40W 4 ~1050mA (adjustable in steps of 50mA) Control Control input: Additional input: IZI-Link / DMX Galvanically isolated 2 x NTC 10KΩ / 1 x 10KΩ potentiometer Miscellaneous Housing: Input connector: Screw terminal input power: Terminal block control: Terminal block led output: Desktop ABS plastic Print connector Max 2,5mm² Max 1,5mm² Max 1,5mm²

2 Dimensions (IZI-LINK) 4 Channel Constant LED-driver DD DMX-512A RoHS 60 INDOOR Tc: 60 C Ta: 40 C IZI.DR.CC mm 32mm 189mm Order Code IZI.DR.CC.4 - ; four channel constant current LED driver; Wiring diagram (IZI-LINK) 4 Channel Constant LED-driver DMX Input DD DD DMX-512A RoHS 60 INDOOR Tc: 60 C Ta: 40 C Input (IZI-Link) IZI.DR.CC Firmware update A firmware update can be done through the IZI-manager LED output 3 LED output 4 LED Behaviour Power ok, Data reception Green Power ok, No data On Over temperature Low voltage Firmware update (IZI-manager) Identify / Green Toggle LED output 2 LED indication Identify mode The Identify mode on the IZI-manager allows identification of each individual fixture/interface. LED output 1

3 Configuration Th can be configured with the IZI-manager Software tool and the IZI-Link programmer cable. The following parameters can be adjusted: Parameters: DMX-address: Device-modes: setting: PWM frequency: DMX fail start: DMX fail operation: Value options 1~512 (dependant on Device ) M1~M8 M16 (stand alone mode) ~1050mA in steps of 50mA Hybrid-mode / PWM-only / Analog-only modez Off / Max / Wave Off / Max / Wave / Hold Default value 1 M1 Hybrid-mode Max Off Next to the configuration of the driver with the IZI-manager, parameters such as internal temperature led driver, Supply voltage, current consumption and Software version can be monitored. User modes Connection options M1 - Single Channel : DMX1 -> Ch2 DMX1 -> Ch3 DMX1 -> Ch4 = Temperature Sensing = Optional Override M2-4 Channel Master DMX1 -> Master DMX2 -> Ch1 DMX3 -> Ch2 DMX4 -> Ch3 DMX5 -> Ch4 = Temperature Sensing = Optional Override M3-4 Channel DMX2 -> Ch2 DMX3 -> Ch3 DMX4 -> Ch4 = Temperature Sensing = Optional Override M4-4 Channel, DualTemp DMX2 -> Ch2 DMX3 -> Ch3 DMX4 -> Ch4 = Temperature Sensing Ch1/2 = Temperature Sensing Ch3/4 Single colour RGBW RGB

4 User modes (Continued) M6 - Tuneable White single control DMX1 -> Intensity DMX2 -> Colour = Temperature Sensing = Optional Override M5 - Connection options (Continued) Warm dimming mode single control DMX1 -> Intensity/Colour, Halogen curve = Temperature Sensing = Optional Override M7 - Tuneable white mode dual control DMX1 -> Intensity Ch1/2 DMX2 -> Colour Ch1/2 DMX3 -> Intensity Ch3/4 DMX4 -> Colour Ch3/4 = Temperature Sensing Ch1/2 = Temperature Sensing Ch3/4 M8 - Warm dimming mode dual control DMX1 -> Intensity/Colour, Halogen curve Ch1/2 DMX2 -> Intensity/Colour, Halogen curve Ch3/4 = Temperature Sensing Ch1/2 = Temperature Sensing Ch3/4 M16 - Analog Control, No DMX = Temperature Sensing = Analog Control by 10k Potmeter settings PWM modes 3= 4= 5= 6= 7= 8= 9= 10 = 11 = 12 = 13 = 14 = 15 = 16 = 17 = 18 = 200mA 250mA 300mA 350mA 400mA 450mA 500mA 550mA 600mA 650mA 700mA 800mA 850mA 900mA 950mA 1000mA 1050mA Hybrid Dimming PWM Dimming only Analog Dimming only For more information about configuring with the IZImanager, see manual of the IZI-manager Tunable white

5 Stand alone The 10KΩ Potentiometer controls the intensity of all channels 1 through 4 simultaneously. When configured in stand alone mode (M16) a 10KΩ Potentiometer can be connected on to terminal block. LED 1 LED 2 LED 3 LED 4 Potentiometer 10KΩ If configuring with the IZI-Link is not wanted or possible, the current output can be configured by adding an external resistor on the terminal. The below table shows the current output with the corresponding resistor value. override 3= 4= 5= 6= 200mA 250mA 300mA 350mA 400mA 450mA 0 Ohm 180 Ohm 390 Ohm 560 Ohm 820 Ohm 1000 Ohm 1200 Ohm 7= 8= 9= 10 = 11 = 12 = 13 = 500mA 550mA 600mA 650mA 700mA 1500 Ohm 1800 Ohm 2200 Ohm 2700 Ohm 3300 Ohm 3900 Ohm 4700 Ohm R 14 = 15 = 16 = 17 = 18 = 850mA 900mA 950mA 1000mA 1050mA 5600 Ohm 6800 Ohm 8200 Ohm Ohm Ohm Connection diagram for RGBW or Mini moodspot fixtures (T568B) Please note that the RGBW fixtures (Like the Cursa / Castor / Canopus RGBW spots, RGBW800 spots and MiniMoodspots) are constant current (CC) led spots. Special RGBW-splitters are available for connecting RGBW/MiniMoodspots in series. Up to 12 RGBW- or Mini-Moodspots can be connected in series on one LED-driver. Maximum Settings for the RGBW- and Mini-Moodspots is 700mA per LED connection Wiring 1 BR/W 2 BR 3 B/W 4G 5 G/W 6B 7 O/W 8O RGBW-LED () (-) () Green (-) Green () Blue (-) Blue () White (-) White Mini-Moodspot () Warmwhite (-) Warmwhite () Coolwhite (-) Coolwhite () Warmwhite (-) Warmwhite () Coolwhite (-) Coolwhite IZI-Drive Cc4 Ch1 () Ch1 (-) Ch2 () Ch2 (-) Ch3 () Ch3 (-) Ch4 () Ch4 (-)