Keysight Technologies Parametric Instrument Accessories

Transcription

1 Keysight Technologies Parametric Instrument Accessies Accessies Guide Technical Overview

2 Table of Contents 1. Introduction Connecting to Fixture Jumper cables ocket modules Connecting to W GND FC Connecting to Prober GND connections /C connections Accessies C accessies B1500A peripherals Connect type Cables Connect plates Adapters & connects... 24

3 1. Introduction This guide provides infmation on how to connect a prober to Keysight Technologies, Inc. semiconduct parametric measurement instruments. This guide also provides infmation on accessies f a variety of Keysight Technologies semiconduct parametric measurement instruments, such as: Keysight B1500A emiconduct Device Analyzer Keysight 4155C/4156C emiconduct Parameter Analyzer Keysight E5270B 8 slot Precision easurement ainframe Keysight E5260A 8 slot High peed easurement ainframe Keysight B2200A fa Leakage witch ainframe Keysight B2201A 14ch Low Leakage witch ainframe Keysight E5250A Low Leakage witch ainframe Figure 1.1. B1500A with Cascade prober Figure 1.2. B1500A with Vect prober Figure 1.3, B1500A with uss prober Figure 1.4. As on the probe station

4 04 Keysight Parametric Instrument Accessies Guide Technical Overview 2. Connecting to Fixture The 16442A and 16442B test fixtures have 6 triaxial input pts. You can connect fce pts of to them by using Triaxial Cable 16494A as shown in Figure 2.1. Triaxial cable 16494A m 16494A m 1-6 Fixture 16442A 16442B 2.1. Jumper cables Table 2.1. Jumper cables ini banana Pin plug 2 mm Approximately 200 mm 11 mm 7 mm As option of 16442A/16442B 16442A-811/16442B-811 f Black (2ea), Blue (2ea), Red (2ea) Parts number f Black (1ea) f Red (1ea) f Blue (1ea) 1 mm Figure 2.1. Connecting s to fixture Pin plug Pin plug 1 mm 7 mm Approximately 200 mm 7 mm 1 mm As option of 16442A/16442B 16442A-812/16442B-812 f Black (2ea), Blue (2ea), Red (2ea) Parts number f Black (1ea) f Red (1ea) f Blue (1ea) ini banana ini clip 2 mm 11 mm Approximately 200 mm 40 mm As option of 16442A/16442B 16442A-813/16442B-813 f Black (2ea), Blue (2ea), Red (2ea) Parts number f Black (1ea) f Red (1ea) f Blue (1ea) ini banana ini banana 11 mm Approximately 200 mm 2 mm As option of 16442A/16442B 16442A-814/16442B-814 f Black (2ea), Blue (2ea), Red (2ea) Parts number f Black (1ea) f Red (1ea) f Blue (1ea)

5 05 Keysight Parametric Instrument Accessies Guide Technical Overview 2.2. ocket modules Table 2.2. ocket odules N1254A inch 16442A-801/16442B-801 N1254A inch inch 43 mm 43 mm 86 mm This socket module is f measurement of virtually any device component, DIPIC, small-scale circuit A-802/16442B inch 84 mm N1254A A-803/16442B inch 0.05 inch 1 mm 8 mm 17.2 mm 1.8 mm N1254A mm 5 mm 3 mm 86 mm This socket module has two transist sockets f measurement of three lead four lead bipolar transists and FETs A-821/16442B mm 5 mm 20 mm 84 mm 3 mm aximum voltage: 200 V N1254A mm mm This socket module has a 28-pin dual-in-line socket. aximum voltage: 230 V 16442A-823/16442B mm mm 84 mm mm N1254A mm mm This socket module has an 18-pin dual-in-line socket. aximum voltage: 230 V 16442A-822/16442B mm 9 mm 9 84 mm 2.54 mm N1254A mm 86 mm This insulation board has minimal leakage current, and so is good f extremely low current measurements A-800/16442B mm 84 mm

6 06 Keysight Parametric Instrument Accessies Guide Technical Overview 3. Connecting to W 3.1. GND An has FORCE (ENE), GARD, and COON, but a GND has ENE, FORCE, and COON as shown in Figure 3.1. You need some st of GND to Kelvin adapter when connecting the GND to standard triaxial connections. Common G N D Ground unit cable 16493L m 16493L m Triaxial triaxial adapter N1254A-107 W B2200A E5250A Figure 3.2. Examples of a GND non-kelvin connection to W Figure 3.1. GND terminal CATION You should use the Keysight 16493L GND cable to connect the GND to the W; do not use a standard triaxial cable. The GND cable can handle the maximum GND current of 4.2 A, but standard triaxial cables are only rated to 1 A. (Non-Kelvin connection) Connect the triaxial connect using an adapter f GND (N1254A-107) as shown in Figure 3.2. F this part, see Table 5.10 in ection 5.6 Adapters. F parts infmation, see Table 3.1. Kelvin connection Connect the dual triaxial connect using a GND to Kelvin Adapter (N1254A-100) as shown in Figure 3.3. F this part, see Table 5.10 in ection 5.6 Adapters. F parts infmation, see Table 3.2. aximum current is restricted when the Kelvin triaxial cable is used. ee Table 3.2. Table 3.1. Parts infmation Description Qty Part number Product Ground unit cable 1.5 m (ax 4.2 A) L-001 Ground unit cable 3.0 m (ax 4.2 A) L-002 Adapter f GND (triaxial (m) triaxial (f)) N1254A-107 G N D Kelvin triaxial cable 16493K m 16493K m GND to Kelvin adapter N1254A-100 Table 3.2. Parts infmation W B2200A Ground unit cable 16493N m Description Qty Part number Product Kelvin triaxial cable 1.5 m (ax 3.0 A) K-001 Kelvin triaxial cable 3.0 m (ax 2.6 A) K-001 Ground unit cable 1.5 m N-001 GND to Kelvin adapter 1 N1254A-100 G N D Figure 3.3. Examples of a GND Kelvin connection to W W B2200A

7 07 Keysight Parametric Instrument Accessies Guide Technical Overview 3.2. An terminal is shown in Figure 3.4. Guard Common () Kelvin triaxial cable 16493K m 16493K m W B2200A B2201A Kelvin triaxial cable 16494B m 16494B m 16494B m W E5250A Figure 3.4. terminal Kelvin connection When Kelvin connection is used, connect a Keysight 16493K Kelvin triaxial cable f B2200A/B2201A as shown in Figure 3.5. F E5250A, connect a Keysight 16494B Kelvin Triaxial Cable as shown in Figure 3.5. You can also use two Keysight 16494A triaxial cables in place of one Kelvin Triaxial Cable. Connect the FORCE and ENE lines to pts separately. Non-Kelvin connection When non-kelvin connection is used, connect the Keysight 16494A triaxial cable between the and W as shown in Figure FC FC of B1500A is connected to CH and CL pt of B2200A/ B2201A by using C input cable 16494F-001 as shown in Figure 3.7. Figure 3.5. Examples of a Kelvin connection to W F C Triaxial cable 16494A m 16494A m Hcur C input cable 16494F m Hpot Lpot Lcur CH CL W E5250A Figure 3.6. Examples of a non-kelvin connection to W W B2200A B2201A Figure 3.7. Examples of a FC connection to W

8 08 Keysight Parametric Instrument Accessies Guide Technical Overview 4. Connecting to Prober 4.1. GND connections An has FORCE (ENE), GARD, and COON, but a GND has ENE, FORCE, and COON as shown in Figure 4.1. You need some st of GND to Kelvin adapter when connecting the GND to standard triaxial connections. G N D Triaxial cable 16493L m 16493L m hielding box Adapter f GND N1254A-107 Prober Common Connect plate DT Figure 4.1. GND terminal Figure 4.2. Examples of a GND non-kelvin connection CATION You should use the Keysight 16493L GND cable to connect the GND to the connect plate; do not use a standard triaxial cable. The GND cable can handle the maximum GND current of 4.2 A, but standard triaxial cables are only rated to 1 A. Non-Kelvin connection Connect the triaxial connect using an adapter f GND (N1254A-107) as shown in Figure 4.2. F this part, see Table 5.10 in ection 5.6 Adapters. F parts infmation, see Table 4.1. Table 4.1. Parts infmation Description Qty Part number Product Ground unit cable 1.5 m (ax 4.2A) L-001 Ground unit cable 3.0 m (ax 4.2A) L-002 Adapter f GND (triaxial (m) triaxial (f)) N1254A-107 G N D Kelvin triaxial cable 16493K m 16493K m hielding box Prober Kelvin connection Connect the dual triaxial connect using a GND to Kelvin Adapter (N1254A-100) as shown in Figure 4.3. F this part, see Table 5.10 in ection 5.6 Adapters. F parts infmation, see Table 4.2. aximum current is restricted when the Kelvin triaxial cable is used. ee Table 4.2. GND to Kelvin adapter N1254A-100 Table 4.2. Parts infmation Connect plate Figure 4.3. Examples of a GND Kelvin connection Description Qty Part number Product Kelvin triaxial cable 1.5 m (ax 3.0 A) K-001 Kelvin triaxial cable 3.0 m (ax 2.6 A) K-002 GND to Kelvin adapter 1 N1254A-100 DT

9 09 Keysight Parametric Instrument Accessies Guide Technical Overview 4.2. /C connections An terminal is shown in Figure 4.4. Guard Common () Kelvin triaxial cable 16493K m 16493K m hielding box Prober Figure 4.4. terminal Kelvin connection These instructions apply when all connections are Kelvin. Two probes must contact the wafer in this connection. Connect a Keysight 16493K Kelvin triaxial cable ( two Keysight 16494A triaxial cables) between the and the connect plate. Connect the FORCE and ENE lines to probes separately. Connect the triaxial connect on the probe cable as shown in Figure 4.5. To prevent oscillations, use sht cables. F parts infmation, see Table 4.3. Non-Kelvin connection These instructions apply when all connections are non-kelvin. Connect the Keysight 16494A triaxial cables between the and the Connect plate. Connect the triaxial connect on the probe cable as shown in Figure 4.6. F parts infmation, see Table 4.4. Table 4.3. Parts infmation Description Qty Part number Product Kelvin triaxial cable 1.5 m (ax 3.0 A) K-001 Kelvin triaxial cable 3.0 m (ax 2.6 A) K-002 Triaxial cable 16494A m 16494A m Connect plate Figure 4.5. Examples of a Kelvin connection Connect plate Table 4.4. Parts infmation Figure 4.6. Examples of a non-kelvin connection hielding box Prober Description Qty Part number Product Triaxial cable 1.5 m A-001 Triaxial cable 3.0 m A-002 DT DT

10 10 Keysight Parametric Instrument Accessies Guide Technical Overview Kelvin to non-kelvin connection These instructions apply when the connections up to the Connect Plate are Kelvin, but the probe is a non-kelvin connection. Kelvin triaxial cable 16493K m 16493K m hielding box Prober Connect a Keysight 16493K Kelvin triaxial cable ( two Keysight 16494A triaxial cables) between the and the Connect plate. Tee triaxial BNC DT Connect the triaxial connect on the probe cable as shown in Figure 4.7. Connect plate Triaxial cable 16494A m Connect the FORCE and ENE lines on this side of the probe input terminal. A Tee Triaxial BNC adapter can be used. F parts infmation, see Table 4.5. Note: When connecting the cable and tee connect as shown in Figure 4.7, space restrictions make an adjacent connect unusable. ince three connects are necessary f a Kelvin connection a connect plate must be used. elect the crect connect plate f your application. To make two Kelvin connections, use a Keysight 16495H. To make three Kelvin connections, use a Keysight 16495J. Figure 4.7. Examples of a Kelvin to non-kelvin connection Table 4.5. Parts infmation Description Qty Part number Product Kelvin triaxial cable 1.5 m K-001 Kelvin triaxial cable 3.0 m K-002 Triaxial cable 0.4 m A-004 Triaxial tee-connect

11 11 Keysight Parametric Instrument Accessies Guide Technical Overview A connection Each A has one Dsub control cable, one triaxial cable, and (optionally) two coaxial cables connected to it. The cables can be connected to the A inside the shielding box through the 16495K plate. C cable N1300A m N1300A m Triaxial cable and Dsub cable m m hielding box The A outputs should be connected to the DT by using triaxial cables as shown in Figure 4.8. When making IV measurements with the s, all measurements are Kelvin. The ENE line infmation is fed back to the via the Dsub cable. When making CV measurements, the four-terminal pair (4TP) connections are crectly terminated inside of the As. The As also allow f a current return path between the outer conducts to stabilize the series inductance and improve accuracy. You must connect the furnished wire between the two As to enable this feature. H R F C H R Dsub Hcur Hpot Lpot Lcur Dsub Triaxial cable and Dsub cable m m Dsub C-cur/AX in C-pot C-pot C-cur/AX in Dsub A A Connect plate 16495K Wire furnished with A (both pin terminals Prober DT Figure 4.8. Examples of an A connection Table 4.5. Parts infmation Description Qty Part number Product Triaxial cable & Dsub cable f A 1.5 m Triaxial cable & Dsub cable f A 3.0 m C cable f B1500A 1.5 m 1 N1300A-001 C cable f B1500A 3.0 m 1 N1300A-002 Connect plate K

12 12 Keysight Parametric Instrument Accessies Guide Technical Overview C positioner-based probing mode The C should be connected to the DT by using triaxial cables as shown in Figure 4.9. C cable N1301A m hielding box When making IV measurements using the s, the outputs of the C function exactly the same as the Kelvin outputs of an (both FORCE and ENE lines are available). C N1301A-100 Note: In Figure 4.9 the ENE lines are not used. When making CV measurements using the FC, only the FORCE outputs of the C are used. C FORCE output1 cresponds to CH, and C FORCE output2 cresponds to CL. The C can be fixed on the prober by using C agnet tand (N1301A-110). F C Hcur H pot Lpot Lcur Prober DT Connect plate 16495K Figure 4.9. Examples of a C remote docking mode Table 4.9. Parts infmation Description Qty Part number Product C unify unit (C) 1 N1301A-100 C unify unit cable (3.0 m) 1 N1301A-102 Connect plate K

13 13 Keysight Parametric Instrument Accessies Guide Technical Overview 5. Accessies 5.1. C accessies B1500A has the multi frequency capacitance measurement unit (FC). There are two types of C connection as follows. tandard four terminal pair (4TP) connection C positioner-based probing mode Accding to your situation, you can select the type of connection. Figure 5.1. tandard four terminal pair (4TP) Figure 5.2. C positioner-based probing

14 14 Keysight Parametric Instrument Accessies Guide Technical Overview Table 5.1. C accessies overview N1300A-001/N1300A F-001 N1301A-100 N1301A-100 N1301A-100 N1301A-102 C w/c Cable, GW N1301A-110 C w/c magnet N1301A-200 N1301A-201 Pin cable f GW GW w/gw cable

15 15 Keysight Parametric Instrument Accessies Guide Technical Overview Table 5.2. C accessies item list Item Description OP instruction N1300A C cable f B1500A N1300A-001 C cable f B1500A (1.5 m) N1300A-002 C cable f B1500A (3.0 m) N1301A C accessies f B1500 N1301A-100 C unify unit (C) N1301A-102 C unify unit cable (3 m) N1301A-110 C magnet stand To fix C on prober top etc. N1301A-200 Guard switch unit (GW) Need to be specified with N1301A-201 N1301A-202. N1301A-201 Guard switch unit cable (1 m) Please specify N1301A-201 N1302A-202 when N1301A-200 is dered. N1301A-202 Guard switch unit cable (3 m) 16494F C input cable 16494F-001 C input cable (2 m) 5.2. B1500A peripherals Table 5.3. B1500A peripherals overview 16444A A A A-003 Table 5.4. B1500A peripherals item list Item Description OP instruction 16444A B1500A accessies 16444A-001 B keyboard Keyboard includes mouse pad and mouse pointer 16444A-002 B mouse B ouse 16444A-003 tylus pen F use with the B1500A touch screen

16 16 Keysight Parametric Instrument Accessies Guide Technical Overview 5.3. Connect type There are two main styles of Kelvin connections. When connecting instruments together, you need to make sure that you have the crect type of Kelvin triaxial cables. Table 5.5. Overview of instrument connect types B1500A Type A Type A connects have two screws, one guide pin, and two triaxial terminals. Type B connects have one screw and two triaxial terminals. These connects are also different in their width and thickness. 4156C+41501B Type A 4155C ingle triaxial E5260A/E5270B Type A B2200A/B2201A inputs Type A

17 17 Keysight Parametric Instrument Accessies Guide Technical Overview Table 5.5. Overview of instrument connect types, (continued) B2200A/B2201A outputs Type B E5250A inputs Type B E5250A outputs (E5252A cards) Type B 16442A/B Type A 16493K/16494B/16493N cables Type A 16494B cable Type B

18 18 Keysight Parametric Instrument Accessies Guide Technical Overview 5.4. Cables everal possibilities exist f connecting the ource onit nits (s) to the DT. The great variety of available cables can be categized into mainly three types: Table 5.6. cables overview 16493K 16494B Triaxial cables have three layers leads: a center conduct f the signal, a middle conduct that is actively driven to be at the same potential as the center conduct to eliminate leakage currents, and a grounded (Common) outer conduct. Kelvin triaxial cables are similar to triaxial cables, except that both the and lines from the run through the same cable. The and lines share a common driven guard and a common outer shield. Kelvin triaxial cables typically give better low-current measurement perfmance than you would get from using two separate triaxial cables f the and lines. The GND cable is a special triaxial cable designed to handle the large currents (up to 4.2 A) that the ground unit can sink. In the GND cable the center conduct is ENE, the middle conduct is FORCE, and the outer conduct is Common. Kelvin triaxial cable Kelvin triaxial cable Connect type Type A Type A Type B W input W output Length option B1500A E526X E527X 415X B220XA E5250A B220XA E5250A 0.4 m 0.8 m 1.5 m 3.0 m 4.0 m NG NG NG N/A N/A 16493K K-002 N/A NG NG NG N/A 16494B B B-002 N/A NG NG NG NG NG NG

19 19 Keysight Parametric Instrument Accessies Guide Technical Overview Table 5.6. cables overview, (continued) A 16493J Triaxial & Dsub cable F A Triaxial cable Interlock cable Connect type Triax B1500A E526X N/A E527X 415X N/A N/A N/A W input B220XA N/A N/A E5250A N/A N/A W output B220XA N/A N/A E5250A N/A N/A Length option 0.4 m N/A 16494A-004 N/A 0.8 m N/A 16494A-003 N/A 1.5 m A J m A J m N/A 16494A-005 N/A Table 5.7. GND cables overview 16493N 16493L Ground unit cable Ground unit cable Connect type Type A Triaxial Triaxial GND B1500A N/A E526X N/A E527X N/A 415X N/A N/A N/A N/A W input B220XA E5250A NG W output B220XA NG E5250A NG Length option 1.5 m 16493N L m N/A 16493L-002

20 20 Keysight Parametric Instrument Accessies Guide Technical Overview 5.5. Connect plates The following connect plates wk with a variety of Keysight semiconduct parametric measurement instruments, such as the B1500, B2200/B2201, E5250, E5260/E5270, 4155/4156 and Prober vend also provides connect plates. If you need the infmation of those connect plates, please kindly contact each prober vend. If you need parts to fix a connect plate, see Table 5.8. Order the quantity you need. (The number of holes in a connect plate is four.) Table 5.8. Parts infmation to fix connect plates Description Qty Part number Product crew pring washer Terminal washer Nut Table 5.9. Connect plates 16495F Half size connect plate f matrix 16495F-001 has 12 triaxial through connects (female to female), an Intlk connect, and a GND connect (triaxial through, female to female). The back of the Intlk connect is designed f soldering F-002 has 12 triaxial connects, an Intlk connect, and a GND connect. The back of each connect is designed f soldering G Full size connect plate f matrix 16495G-001 has 24 triaxial through connects (female to female), an Intlk connect, and a GND connect (triaxial through, female to female). The back of the Intlk connect is designed f soldering G-002 has 24 triaxial connects, an Intlk connect, and a GND connect. The back of each connect is designed f soldering H Half size connect plate f analyzer 16495H-001 has 6 triaxial through connects (female to female), 6 BNC through connects (female to female), an Intlk connect, and a GND connect (triaxial through, female to female). The back of the Intlk connect is designed f soldering H-002 has 6 triaxial connects, 6 BNC connects, an Intlk connect, and a GND connect. The back of each connect is designed f soldering J Half size connect plate f analyzer 16495J-001 has 8 triaxial through connects (female to female), 4 BNC through connects (female to female), an Intlk connect, and a GND connect (triaxial through, female to female). The back of the Intlk connect is designed f soldering J-002 has 8 triaxial connects, 4 BNC connects, an Intlk connect, and a GND connect. The back of each connect is designed f soldering K Half size connect plate with universal cable holder 16495K-001 does not have any connects. This plate provides the cable hole and the cover with rubber used to block the light from the cable hole. This plate will be used with the Keysight E5288A Atto /witch nit (A) the Keysight N1301A-200 Guard witch nit (GW) that will be installed in the shielding box. The cable hole is to pass the cables from the A GW to the instrument such as the Keysight B1500A, E5270B, and so on. And the cables will be fixed to the shielding box by using the cover with rubber that will close the opening of the cable hole.

21 21 Keysight Parametric Instrument Accessies Guide Technical Overview A. Front view Common INPT 1 1 Guard (sense) Triaxial connect (f ) ignal line 9 10 Common Coaxial connect (f FC) Common Triaxial connect (f GND) GND Intlk! INTLK terminal B. Rear view Triaxial connect Ground terminal Common terminal Triaxial connect Ground terminal Common terminal The difference between the Keysight 16495F, H and J is the number of the triaxial and coaxial connects. Coaxial connect Coaxial connect INTLK terminal Triaxial connect (f GND) INTLK terminal Keysight 16495H-001 Keysight 16495H-002 Triaxial connect (f GND) Figure 5.3. Front view and rear view of connect plate

22 22 Keysight Parametric Instrument Accessies Guide Technical Overview Ø 3.2 INPT etal cover GND Intlk! nit: mm etal cover Keysight 16495H-002 (The difference between the Keysight F, H and J is the number of the triaxial and coaxial connects.) Note: etal cover is f preventing electrical shock. etal cover is furnished with F/G/H/J-002 only Figure 5.4. Dimensions of the connect plate (Keysight 16495F/H/J) Triaxial Coaxial Triaxial Coaxial A. Connect type (16495F/G/H/J-001) B. older type (16495F/G/H/J-002) Figure 5.5. Connection type of connect plate (rear)

23 23 Keysight Parametric Instrument Accessies Guide Technical Overview Ø nit: mm Figure 5.6. Dimensions of the connect plate (Keysight 16495G)

24 24 Keysight Parametric Instrument Accessies Guide Technical Overview 5.6. Adapters and connects If you need to make a connection between a triaxial connect and a coaxial connect, use a triaxial-coaxial adapter. Table Parts infmation Item Description Qty Part number Illustration Table 5.10 shows the adapter infmation provided by Keysight. If you need an adapter which is not provided, contact a local parts vend. WARNING To avoid injury, always be sure to use a shielding box and Interlock when you make a measurement. N1254A-100 N1254A-101 N1254A-102 GND to Kelvin adapter Triaxial (m) Coaxial (f) Triaxial (f) Coaxial (m) m Common f f Do not use the adapters in Table 5.10 when the GARD line connects to the outer conduct of the connect adapter. Because they connect GARD line and outer conduct of the connect adapter, the potential of the GARD terminal is equal to the output voltage and there is a potential f high voltage electrical shock at the adapter and connect. N1254A-103 N1254A-104 N1254A-105 N1254A-106 N1254A-107 Triaxial (m) Coaxial (f) Triaxial (f) Coaxial (m) Triaxial (f) Coaxial (m) Triaxial (m) Coaxial (f) Triaxial (m) Triaxial (f)

25 25 Keysight Parametric Instrument Accessies Guide Technical Overview Keysight B2900A eries Precision ource/easure nit F me infmation on Keysight Technologies products, applications services, please contact your local Keysight office. The complete list is available at: Keysight B1500A emiconduct Device Analyzer Keysight B1505A Power Device Analyzer/Curve Tracer mykeysight A personalized view into the infmation most relevant to you. Three-Year Warranty Keysight s commitment to superi product quality and lower total cost of ownership. The only test and measurement company with three-year warranty standard on all instruments, wldwide. Keysight Assurance Plans p to five years of protection and no budgetary surprises to ensure your instruments are operating to specification so you can rely on accurate measurements. Keysight Technologies, Inc. DEKRA Certified IO 9001:2008 Quality anagement ystem Keysight Channel Partners Get the best of both wlds: Keysight s measurement expertise and product breadth, combined with channel partner convenience. Americas Canada (877) Brazil exico nited tates (800) Asia Pacific Australia China Hong Kong India Japan 0120 (421) 345 Kea alaysia ingape Taiwan Other AP Countries (65) Europe & iddle East Austria Belgium Finland France Germany Ireland Israel Italy Luxembourg Netherlands Russia pain weden witzerland Opt. 1 (DE) Opt. 2 (FR) Opt. 3 (IT) nited Kingdom F other unlisted countries: (BP ) This infmation is subject to change without notice. Keysight Technologies, Published in A, August 3, EN