PXIe-6570 DEVICE SPECIFICATIONS. 32-Channel Digital Pattern Instrument

Size: px
Start display at page:

Download "PXIe-6570 DEVICE SPECIFICATIONS. 32-Channel Digital Pattern Instrument"

Transcription

1 DEVICE SPECIFICATIONS PXIe Channel Digital Pattern Instrument This document lists the specifications for the PXIe When using the PXIe-6570 in the Semiconductor Test System, refer to the Semiconductor Test System Specifications. Specifications are subject to change without notice. Refer to ni.com/manuals for the most recent specifications. NI defines the capabilities and performance of its Test & Measurement instruments as Warranted specifications, Typical specifications, and Characteristics. Warranted specifications describe the warranted, traceable product performance, including the effects of temperature and uncertainty unless otherwise noted. Typical specifications are unwarranted values that are representative of a majority of units, including the effects of temperature and uncertainty unless otherwise noted. Characteristics are unwarranted values that are relevant to the use of the product and convey the expected performance of the product. Specifications in this document are Characteristics unless otherwise noted. Specifications are valid under the following conditions unless otherwise noted: 0 C to 45 C operating temperature. Accuracy specifications are valid within ±5 ºC of the last self-calibration temperature. The PXIe-6570 is within the 1 year recommended calibration interval. The DUT Ground Sense (DGS) is the same potential as the Ground (GND) pins. Note The DGS feature is only available on PXIe-6570 module revisions C-xxL or later. Chassis fans are set to the highest setting if the PXI Express chassis supports multiple fans speeds. Allow a 30 minute warm-up time. Caution Do not operate the PXIe-6570 in a manner not specified in the user documentation. Product misuse can result in a hazard. You can compromise the safety protection built into the product if the product is damaged in any way. If the product is damaged, return it to NI for repair.

2 Contents Note When the pin electronics on the PXIe-6570 are in the disconnect state, some I/O protection and sensing circuitry remain connected. Do not subject the PXIe-6570 to voltages beyond the supported measurement range. General... 3 Timing... 3 Vector Timing...3 Clock Generation... 3 Drive and Compare Formats... 4 Pin Data States... 4 Edge Timing...5 Driver, Comparator, Load... 6 Driver... 6 Comparator...6 Active Load...6 PPMU...7 PPMU Force Voltage...7 PPMU Measure Voltage...7 PPMU Force Current... 7 PPMU Measure Current...8 PPMU Programmable Aperture Time...9 Pattern Control Opcodes...10 Pipeline Latencies Source and Capture Frequency Measurements Calculating Frequency Counter Error Calibration Interval Physical Characteristics Power Requirements Environment...14 Operating Environment...14 Storage Environment...15 Shock and Vibration...15 Safety Voltages...15 Compliance and Certifications...15 Safety Electromagnetic Compatibility CE Compliance Online Product Certification Environmental Management ni.com PXIe-6570 Specifications

3 General Channel count 32 Multi-site resources per instrument 8 System channel count Large Vector Memory (LVM) History RAM (HRAM) Maximum allowable offset 2 (DGS minus GND) Supported measurement range 128M vectors 1,023 cycles ±300 mv -2 V to 6 V Timing Vector Timing Maximum vector rate Vector period range Vector period resolution Timing control Vector period Edge timing Drive formats Clock Generation 100 MHz 10 ns to 40 µs (100 MHz to 25 khz) 38 fs Vector-by-vector on the fly Master clock source PXIe_CLK100 3 Clock domains Per channel, vector-by-vector on the fly Per channel, vector-by-vector on the fly One (independent clock domains on a single instrument not supported) 1 The system channel count is the maximum number of channels available when using multiple PXIe-6570 instruments in a single chassis as a digital subsystem. Some functionality described in this document requires that a PXIe-6674T synchronization module be used in conjunction with each digital subsystem. 2 If the total voltage sourced or driven on any pin relative to GND exceeds the supported measurement range, instrument performance may be degraded. 3 Sourced from chassis 100 MHz backplane reference clock, external 10 MHz reference, or PXIe-6674T. PXIe-6570 Specifications National Instruments 3

4 Drive and Compare Formats Drive formats 100 MHz maximum vector rate Non-Return (NR), Return to Low (RL), Return to High (RH) 50 MHz maximum vector rate Surround by Complement (SBC) Compare formats Edge strobe Figure 1. Drive Formats Vector Cycle Pin State X 0 1 Non-Return (NR) Return to Low (RL) Return to High (RH) Surround by Complement (SBC) Drive On Drive Data Drive Return Drive Data Drive Return Drive On Drive Data Drive Return Drive Off Drive On Drive Data Drive Return Drive On Drive Data Drive Return Indeterminate State Pin Data States Pin States - Repeat previous cycle. Do not use a dash (-) for the pin state on the first vector of a pattern file unless the file is used only as a target of a jump or call operation. 0 Drive zero. 1 Drive one. L Compare low. H Compare high. X Do not drive; mask compare. 4 ni.com PXIe-6570 Specifications

5 V Compare high or low, not midband; store results from capture functionality if configured. D Drive data from source functionality if configured. M Compare midband, not high or low. Note Termination mode settings affect the termination applied to all non-driving pin states. Non-drive states include L, H, M, V, X and potentially -. Refer to the Programmable input termination mode specification for more information. Edge Timing Edge Types Drive edges Compare edge Number of time sets 4 31 Edge Generation Timing Edge placement range Minimum Maximum Minimum required edge separation Between any driven data change Between any Drive On and Drive Off edges Between Compare Strobes Edge placement resolution Edge placement accuracy 5 Drive Compare Overall timing accuracy 5 TDR deskew adjustment resolution 4; drive on, drive data, drive return, drive off 1; strobe Start of vector period (0 ns) 5 vector periods or 40 µs, whichever is smaller 5 ns 5 ns 5 ns ps ±500 ps, warranted ±500 ps, warranted ±1.5 ns, warranted ps 4 31 time sets can be configured. One additional time set, represented by a -, repeats the previous time set. 5 For specifications across multiple instruments in a Semiconductor Test System, refer to the Semiconductor Test System Specifications. PXIe-6570 Specifications National Instruments 5

6 Driver, Comparator, Load Driver Signal type Programmable levels Voltage levels Range (V IH, V IL, V TERM ) Minimum swing (V IH minus V IL ) Single-ended, referenced to the DGS pin when connected. Otherwise referenced to GND. V IH, V IL, V TERM -2 V to 6 V Resolution (V IH, V IL, V TERM ) 122 µv Accuracy (V IH, V IL, V TERM ) Maximum DC drive current Output impedance Rise/fall time, 20% to 80% Comparator Signal type Programmable levels Voltage levels Range (V OH, V OL ) 400 mv, into a 1 MΩ load ±15 mv, 1 MΩ load, warranted ±32 ma 50 Ω 1.2 ns, up to 5 V Single-ended, referenced to the DGS pin when connected. Otherwise referenced to GND. V OH, V OL -2 V to 6 V Resolution (V OH, V OL ) 122 µv Accuracy (V OH, V OL ) Programmable input termination modes Leakage current Active Load Programmable levels Commutating voltage (V COM ) Range ±25 mv, between -1.5 V to 5.8 V, warranted High Z, 50 Ω to V TERM, Active Load <15 na, in the High Z termination mode I OH, I OL -2 V to 6 V Resolution 122 µv 6 ni.com PXIe-6570 Specifications

7 Current levels Range Resolution Accuracy 1.5 ma to 24 ma 488 na 1 ma, 3 V over/under drive, typical PPMU PPMU Force Voltage Signal type Voltage levels Range Resolution Accuracy PPMU Measure Voltage Signal type Voltage levels Range Resolution Accuracy PPMU Force Current Single-ended, referenced to the DGS pin when connected. Otherwise referenced to GND. -2 V to 6 V 122 μv ±15 mv, 1 MΩ load, warranted Single-ended, referenced to the DGS pin when connected. Otherwise referenced to GND. -2 V to 6 V 228 μv ±5 mv, warranted Table 1. PPMU Force Current Accuracy Range Resolution Accuracy ±2 µa 60 pa ±1% of range for Zone 1 of Figure 2. on page 8, warranted ±32 µa 980 pa ±128 μa 3.9 na ±2 ma 60 na ±32 ma 980 na PXIe-6570 Specifications National Instruments 7

8 Figure 2. Warranted Current Accuracy Zone for PPMU Force Current 100 Percent of Current Range Forced (%) Zone Voltage (V) PPMU voltage clamps Range Resolution Accuracy PPMU Measure Current -2 V to 6 V 122 μv ±100 mv, typical Table 2. PPMU Measure Current Accuracy Range Resolution Accuracy ±2 μa 460 pa ±1% of range for Zone 1 of Figure 3. on page 9, warranted ±32 μa 7.3 na ±1.5% of range for Zone 2 of Figure 3. on page 9, warranted ±128 μa 30 na ±2 ma 460 na ±32 ma 7.3 μa 8 ni.com PXIe-6570 Specifications

9 Figure 3. Warranted Current Accuracy Zones for PPMU Measure Current 100 Percent of Current Range Measured (%) Zone 1 Zone Voltage (V) 6 PPMU Programmable Aperture Time Aperture time Minimum 4 μs Maximum 65 ms Resolution 4 μs PXIe-6570 Specifications National Instruments 9

10 Figure 4. Voltage Measurement Noise for Given Aperture Times, Typical 200μ 190μ 180μ 170μ 160μ 150μ 140μ RMS Noise (V) 130μ 120μ 110μ 100μ 90μ 80μ 70μ 60μ 50μ 40μ 30μ 20μ 10μ 0 1μ 10μ 100μ 1m 10m 100m Aperture Time (s) Pattern Control Opcodes Refer to the following table for supported opcodes. Using matched and failed opcode parameters with multiple PXIe-6570 instruments requires the PXIe-6674T synchronization module. Other uses of flow-control opcodes with multiple PXIe-6570 instruments only require NI-TCLK synchronization. 10 ni.com PXIe-6570 Specifications

11 Category Supported Opcodes Flow Control repeat jump jump_if set_loop end_loop exit_loop exit_loop_if call return keep_alive match halt Sequencer Flags and Registers set_seqflag clear_seqflag write_reg Signal set_signal pulse_signal clear_signal Digital Source and Capture capture_start capture capture_stop source_start source Pipeline Latencies Minimum delay between source_start opcode and the first source opcode or subsequent source_start opcode Matched and failed condition pipeline latency 3 μs 80 cycles PXIe-6570 Specifications National Instruments 11

12 Source and Capture Digital Source 6 Operation modes Serial and parallel; broadcast and site-unique Source memory size 32 MB (256 Mbit) total Maximum waveforms 512 Digital Capture 6 Operation modes Serial and parallel; site-unique Capture memory size 1 million samples Maximum waveforms 512 Frequency Measurements Frequency counter measure frequency Range Accuracy 5 khz to 200 MHz, 2.5 ns minimum pulse width See Calculating Frequency Counter Error Calculating Frequency Counter Error Use the following equation to calculate the frequency counter error (ppm) * 1, 000, 000 where MeasurementTime is the time, in seconds, over which the frequency counter measurement is configured to run UnknownClockPeriod is the time, in seconds, of the period of the signal being measured TB err is the error of the Clk100 timebase Refer to the following table for a few examples of common Clk100 timebase accuracies. 6 To learn how to calculate achievable data rates for Digital Source or Digital Capture, visit ni.com/ info and enter the info code DigitalSource or DigitalCapture to access the Calculating Digital Source Rate tutorial or the Calculating Digital Capture Rate tutorial. 12 ni.com PXIe-6570 Specifications

13 Table 3. TB err PXI Express Hardware Specification Revision 1.0 PXIe-1085 Chassis PXIe-6674T Override 100 µ (100 ppm) 25 µ (25 ppm) 80 n (80 ppb) Example 1: Calculating Error with a PXIe-1085 Chassis Calculate the error of performing a frequency measurement of a 10 MHz clock (100 ns period) with a 1 ms measurement time using the PXIe-Clk100 provided by the PXIe-1085 chassis as the timebase. Solution 25µ 1 25µ * 1, 000, 000 = 45 Example 2: Calculating Error when Overriding with the PXIe-6674T Calculate the error if you override the PXIe-Clk100 timebase with the PXIe-6674T and increase the measurement time to 10 ms. Solution * 1, 000, 000 = 2 Calibration Interval Recommended calibration interval 1 year PXIe-6570 Specifications National Instruments 13

14 Physical Characteristics Clean the hardware with a soft, nonmetallic brush. Make sure that the hardware is completely dry and free from contaminants before returning it to service. PXIe slots 2 Dimensions 131 mm 42 mm 213 mm (5.16 in in in.) Weight 920 g (32.45 oz.) Power Requirements Caution The protection provided by the PXIe-6570 can be impaired if it is used in a manner not described in the user documentation. The PXIe-6570 draws current from a combination of the 3.3 V and 12 V power rails. The maximum current drawn from each of these rails can vary depending on the PXIe-6570 mode of operation. The total power consumption does not exceed the input power specification. Input power Current Draw 68 W 3.3 V 4.4 A 12 V 4.7 A Environment Maximum altitude Pollution Degree 2 2,000 m (800 mbar) (at 25 C ambient temperature) Indoor use only. Operating Environment Ambient temperature range Relative humidity range 0 C to 45 C (Tested in accordance with IEC and IEC Meets MIL-PRF-28800F Class 3 low temperature limit and MIL-PRF-28800F Class 4 high temperature limit.) 10% to 90%, noncondensing (Tested in accordance with IEC ) 14 ni.com PXIe-6570 Specifications

15 Storage Environment Ambient temperature range Relative humidity range -40 C to 71 C (Tested in accordance with IEC and IEC Meets MIL-PRF-28800F Class 3 limits.) 5% to 95%, noncondensing (Tested in accordance with IEC ) Shock and Vibration Operating shock Random vibration Operating Nonoperating 30 g peak, half-sine, 11 ms pulse (Tested in accordance with IEC Meets MIL-PRF-28800F Class 2 limits.) 5 Hz to 500 Hz, 0.3 g rms 5 Hz to 500 Hz, 2.4 g rms (Tested in accordance with IEC Nonoperating test profile exceeds the requirements of MIL-PRF-28800F, Class 3.) Safety Voltages Connect only voltages that are within these limits. Supported measurement range -2 V to 6 V Caution Do not connect the system to signals or use for measurements within Measurement Categories II, III, or IV. Compliance and Certifications Safety This product is designed to meet the requirements of the following electrical equipment safety standards for measurement, control, and laboratory use: IEC , EN UL , CSA Note For UL and other safety certifications, refer to the product label or the Online Product Certification section. PXIe-6570 Specifications National Instruments 15

16 Electromagnetic Compatibility This product meets the requirements of the following EMC standards for electrical equipment for measurement, control, and laboratory use: EN (IEC ): Class A emissions; Basic immunity EN (CISPR 11): Group 1, Class A emissions EN (CISPR 22): Class A emissions EN (CISPR 24): Immunity AS/NZS CISPR 11: Group 1, Class A emissions AS/NZS CISPR 22: Class A emissions FCC 47 CFR Part 15B: Class A emissions ICES-001: Class A emissions Note In the United States (per FCC 47 CFR), Class A equipment is intended for use in commercial, light-industrial, and heavy-industrial locations. In Europe, Canada, Australia, and New Zealand (per CISPR 11), Class A equipment is intended for use only in heavy-industrial locations. Note Group 1 equipment (per CISPR 11) is any industrial, scientific, or medical equipment that does not intentionally generate radio frequency energy for the treatment of material or inspection/analysis purposes. Note For EMC declarations, certifications, and additional information, refer to the Online Product Certification section. CE Compliance This product meets the essential requirements of applicable European Directives, as follows: 2014/35/EU; Low-Voltage Directive (safety) 2014/30/EU; Electromagnetic Compatibility Directive (EMC) Online Product Certification Refer to the product Declaration of Conformity (DoC) for additional regulatory compliance information. To obtain product certifications and the DoC for this product, visit ni.com/ certification, search by model number or product line, and click the appropriate link in the Certification column. Environmental Management NI is committed to designing and manufacturing products in an environmentally responsible manner. NI recognizes that eliminating certain hazardous substances from our products is beneficial to the environment and to NI customers. For additional environmental information, refer to the Minimize Our Environmental Impact web page at ni.com/environment. This page contains the environmental regulations and 16 ni.com PXIe-6570 Specifications

17 directives with which NI complies, as well as other environmental information not included in this document. Waste Electrical and Electronic Equipment (WEEE) EU Customers At the end of the product life cycle, all NI products must be disposed of according to local laws and regulations. For more information about how to recycle NI products in your region, visit ni.com/environment/weee. 电子信息产品污染控制管理办法 ( 中国 RoHS) 中国客户 National Instruments 符合中国电子信息产品中限制使用某些有害物质指令 (RoHS) 关于 National Instruments 中国 RoHS 合规性信息, 请登录 ni.com/environment/rohs_china (For information about China RoHS compliance, go to ni.com/environment/rohs_china.) PXIe-6570 Specifications National Instruments 17

18 Refer to the NI Trademarks and Logo Guidelines at ni.com/trademarks for information on NI trademarks. Other product and company names mentioned herein are trademarks or trade names of their respective companies. For patents covering NI products/technology, refer to the appropriate location: Help»Patents in your software, the patents.txt file on your media, or the National Instruments Patent Notice at ni.com/patents. You can find information about end-user license agreements (EULAs) and third-party legal notices in the readme file for your NI product. Refer to the Export Compliance Information at ni.com/ legal/export-compliance for the NI global trade compliance policy and how to obtain relevant HTS codes, ECCNs, and other import/export data. NI MAKES NO EXPRESS OR IMPLIED WARRANTIES AS TO THE ACCURACY OF THE INFORMATION CONTAINED HEREIN AND SHALL NOT BE LIABLE FOR ANY ERRORS. U.S. Government Customers: The data contained in this manual was developed at private expense and is subject to the applicable limited rights and restricted data rights as set forth in FAR , DFAR , and DFAR National Instruments. All rights reserved D-01 June 27, 2017

PXIe Contents SPECIFICATIONS. 100 MVector/s PXI Digital Pattern Instrument

PXIe Contents SPECIFICATIONS. 100 MVector/s PXI Digital Pattern Instrument SPECIFICATIONS PXIe-6570 100 MVector/s PXI Digital Pattern Instrument These specifications apply to the PXIe-6570. When using the PXIe-6570 in the Semiconductor Test System, refer to the Semiconductor

More information

PXIe Contents SPECIFICATIONS. 32-Channel Digital Pattern Instrument

PXIe Contents SPECIFICATIONS. 32-Channel Digital Pattern Instrument SPECIFICATIONS PXIe-6571 32-Channel Digital Pattern Instrument These specifications apply to the PXIe-6571. When using the PXIe-6571 in the Semiconductor Test System, refer to the Semiconductor Test System

More information

NI PXIe Contents. About These Specifications DEVICE SPECIFICATIONS. 3 GHz Ω Multiplexer (SP16T)

NI PXIe Contents. About These Specifications DEVICE SPECIFICATIONS. 3 GHz Ω Multiplexer (SP16T) DEVICE SPECIFICATIONS NI PXIe-2748 3 GHz 16 1 50 Ω Multiplexer (SP16T) This document lists specifications for the NI PXIe-2748 (NI 2748) multiplexer module. All specifications are subject to change without

More information

NI PXI Contents DEVICE SPECIFICATIONS. RF Attenuator

NI PXI Contents DEVICE SPECIFICATIONS. RF Attenuator DEVICE SPECIFICATIONS NI PXI-5695 RF Attenuator This document lists the specifications of the NI PXI-5695 (NI 5695) RF attenuator. Specifications are warranted by design and under the following conditions

More information

USRP Contents. Definitions. Conditions SPECIFICATIONS. Software Defined Radio Reconfigurable Device

USRP Contents. Definitions. Conditions SPECIFICATIONS. Software Defined Radio Reconfigurable Device SPECIFICATIONS USRP-2944 Software Defined Radio Reconfigurable Device Contents Definitions...1 Conditions... 1 Transmitter... 2 Receiver... 2 Power... 3 Onboard DRAM...3 Physical Characteristics... 3 Environment...4

More information

USRP Contents. Definitions SPECIFICATIONS. Software Defined Radio Reconfigurable Device

USRP Contents. Definitions SPECIFICATIONS. Software Defined Radio Reconfigurable Device SPECIFICATIONS USRP-2943 Software Defined Radio Reconfigurable Device These specifications apply to the USRP-2943 40 MHz Software Defined Radio Device and the USRP-2943 120 MHz Software Defined Radio Device.

More information

USRP Contents. Definitions SPECIFICATIONS. 50 MHz to 2.2 GHz Tunable RF Transceiver

USRP Contents. Definitions SPECIFICATIONS. 50 MHz to 2.2 GHz Tunable RF Transceiver SPECIFICATIONS USRP-2950 50 MHz to 2.2 GHz Tunable RF Transceiver These specifications apply to the USRP-2950 40 MHz Software Defined Radio Device and the USRP-2950 120 MHz Software Defined Radio Device.

More information

USRP Contents. Definitions. Conditions SPECIFICATIONS. Software Defined Radio Device

USRP Contents. Definitions. Conditions SPECIFICATIONS. Software Defined Radio Device SPECIFICATIONS USRP-2922 Software Defined Radio Device Contents Definitions...1 Conditions... 1 Transmitter... 2 Receiver... 2 Power... 3 Physical Characteristics... 3 Environment...4 Operating Environment...4

More information

PXIe Contents SPECIFICATIONS. RF Amplifier

PXIe Contents SPECIFICATIONS. RF Amplifier SPECIFICATIONS PXIe-5698 RF Amplifier Contents Definitions...2 Conditions... 2 Amplitude...3 Minimal Gain... 3 Noise Figure...4 Average Noise Level... 5 Absolute Amplitude Accuracy...7 Spurious Responses...8

More information

USRP Contents. Definitions SPECIFICATIONS. 10 MHz to 6 GHz Tunable RF Transceiver

USRP Contents. Definitions SPECIFICATIONS. 10 MHz to 6 GHz Tunable RF Transceiver SPECIFICATIONS USRP-2954 10 MHz to 6 GHz Tunable RF Transceiver The USRP-2954 contains a GPS-disciplined oscillator (GPSDO), which enables you to lock the internal clocks to a GPS reference signal, synchronize

More information

CDA Contents. Definitions SPECIFICATIONS. Clock Distribution Device

CDA Contents. Definitions SPECIFICATIONS. Clock Distribution Device SPECIFICATIONS CDA-2990 Clock Distribution Device These specifications apply to the CDA-2990 Clock Distribution Device and the CDA-2990 Clock Distribution Device with GPSDO. When not otherwise specified,

More information

USRP Contents. Definitions. Conditions SPECIFICATIONS. Software Defined Radio Device

USRP Contents. Definitions. Conditions SPECIFICATIONS. Software Defined Radio Device SPECIFICATIONS USRP-2921 Software Defined Radio Device Contents Definitions...1 Conditions... 1 Transmitter... 2 Receiver... 2 Half-Duplex Device... 3 Power... 3 Physical Characteristics... 4 Environment...4

More information

NI PXI Contents. About These Specifications DEVICE SPECIFICATIONS GHz Dual Transfer Switch 50 Ω Relay Module

NI PXI Contents. About These Specifications DEVICE SPECIFICATIONS GHz Dual Transfer Switch 50 Ω Relay Module DEVICE SPECIFICATIONS NI PXI-2598 26.5 GHz Dual Transfer Switch 50 Ω Relay Module This document lists specifications for the NI PXI-2598 (PXI-2598) relay module. All specifications are subject to change

More information

PXI Contents. Definitions SPECIFICATIONS. ±100 V, 2 W Precision PXI Source Measure Unit. These specifications apply to the PXI-4132.

PXI Contents. Definitions SPECIFICATIONS. ±100 V, 2 W Precision PXI Source Measure Unit. These specifications apply to the PXI-4132. SPECIFICATIONS PXI-4132 ±100 V, 2 W Precision PXI Source Measure Unit These specifications apply to the PXI-4132. Contents Definitions...1 Conditions... 2 Device Capabilities... 2 SMU Specifications...

More information

PXIe Contents SPECIFICATIONS. RF Preselector Module

PXIe Contents SPECIFICATIONS. RF Preselector Module SPECIFICATIONS PXIe-5693 RF Preselector Module Contents Definitions...2 Conditions... 2...2 Preselector Filters...3 Notch Filters...5 Amplitude...6 Gain...6 Gain Range...6 Gain Accuracy...7 Low- Bypass

More information

PXI Contents. PXI-2585 Specifications. Topology DEVICE SPECIFICATIONS. 10-Channel Multiplexer

PXI Contents. PXI-2585 Specifications. Topology DEVICE SPECIFICATIONS. 10-Channel Multiplexer DEVICE SPECIFICATIONS PXI-2585 10-Channel Multiplexer This document lists specifications for the PXI-2585 general-purpose relay module. All specifications are subject to change without notice. Visit ni.com/manuals

More information

PXI Contents SPECIFICATIONS. 1.3 GHz RF Analog Signal Generator

PXI Contents SPECIFICATIONS. 1.3 GHz RF Analog Signal Generator SPECIFICATIONS PXI-5650 1.3 GHz RF Analog Signal Generator Contents Definitions...2 Conditions... 2 Frequency...2 Frequency Settling Time... 3 Reference Clock...3 Internal Clock...3 Internal Reference

More information

1- or 2-Port, High-Speed, Flexible Data Rate PXI CAN Interface Module

1- or 2-Port, High-Speed, Flexible Data Rate PXI CAN Interface Module SPECIFICATIONS PXI-8512 1- or 2-Port, High-Speed, Flexible Data Rate PXI CAN Interface Module This document lists specifications for the PXI-8512 1-port and 2-port CAN interface module. Definitions Warranted

More information

PXIe Contents SPECIFICATIONS. 3.3 GHz RF Analog Signal Generator

PXIe Contents SPECIFICATIONS. 3.3 GHz RF Analog Signal Generator SPECIFICATIONS PXIe-5651 3.3 GHz RF Analog Signal Generator Contents Definitions...2 Conditions... 2 Frequency...2 Frequency Settling Time... 3 Reference Clock...3 Internal Clock...3 Internal Reference

More information

PXI Contents SPECIFICATIONS. 6.6 GHz RF Analog Signal Generator

PXI Contents SPECIFICATIONS. 6.6 GHz RF Analog Signal Generator SPECIFICATIONS PXI-5652 6.6 GHz RF Analog Signal Generator Contents Definitions...2 Conditions... 2 Frequency...2 Frequency Settling Time... 3 Reference Clock...3 Internal Clock...3 Internal Reference

More information

100 MHz Bandwidth, 12-Bit PXI Waveform Generator

100 MHz Bandwidth, 12-Bit PXI Waveform Generator SPECIFICATIONS PXI-5404 100 MHz Bandwidth, 12-Bit PXI Waveform Generator Contents Conditions... 1 CH 0 Outputs... 2 CH 0 SINE Out... 2 CH 0 CLOCK Out...4 PFI 0 I/O...5 REF IN... 6 REF OUT... 7 Start Trigger...

More information

PXIe Contents. Definitions SPECIFICATIONS. 8.5 GHz Vector Network Analyzer

PXIe Contents. Definitions SPECIFICATIONS. 8.5 GHz Vector Network Analyzer SPECIFICATIONS PXIe-5632 8.5 GHz Vector Network Analyzer Contents Definitions...1 Conditions... 2 General Information...2 Source Characteristics...3 Receiver Characteristics...5 Measurement Speed... 6

More information

PXI Contents SPECIFICATIONS. ±20 V, 40 W PXI Source Measure Unit

PXI Contents SPECIFICATIONS. ±20 V, 40 W PXI Source Measure Unit SPECIFICATIONS PXI-4130 ±20 V, 40 W PXI Source Measure Unit These specifications apply to the PXI-4130 with APS-4100 auxiliary power supply and to the PXI-4130 without auxiliary power supply. Contents

More information

This document lists the specifications for the NI PXI The PXI-5900 is a differential amplifier.

This document lists the specifications for the NI PXI The PXI-5900 is a differential amplifier. DEVICE SPECIFICATIONS NI PXI-5900 Differential Amplifier This document lists the specifications for the NI PXI-5900. The PXI-5900 is a differential amplifier. Contents PXI-5900 Specifications... 1 Analog

More information

High-Speed/Flexible Data-Rate CAN Characteristics 5 VDC

High-Speed/Flexible Data-Rate CAN Characteristics 5 VDC SPECIFICATIONS TRC-8543 CAN HS/FD or LS/FT Transceiver Cable The following specifications are typical for the range -40 C to 70 C unless otherwise noted. High-Speed/Flexible Data-Rate CAN Characteristics

More information

Refer to the NI Switches Help at ni.com/manuals for detailed topology information.

Refer to the NI Switches Help at ni.com/manuals for detailed topology information. DEVICE SPECIFICATIONS NI PXI/PXIe-2593 500 MHz Dual 8 1 50 Ω Multiplexer This document lists specifications for the NI PXI/PXIe-2593 (NI 2593). All specifications are subject to change without notice.

More information

PXIe Contents. Definitions SPECIFICATIONS. 8.5 GHz Vector Network Analyzer

PXIe Contents. Definitions SPECIFICATIONS. 8.5 GHz Vector Network Analyzer SPECIFICATIONS PXIe-5632 8.5 GHz Vector Network Analyzer Contents Definitions...1 Conditions... 2 General Information...2 Source Characteristics...3 Receiver Characteristics...5 Measurement Speed... 6

More information

Note Using the NI 5751/5751B in a manner not described in this document may impair the protection that the NI 5751/5751B provides.

Note Using the NI 5751/5751B in a manner not described in this document may impair the protection that the NI 5751/5751B provides. DEVICE SPECIFICATIONS NI 5751/5751B 50 MS/s Digitizer Adapter Module This document lists specifications for the NI 5751/5751B adapter module. Pair these specifications with the specifications listed in

More information

PXIe Contents SPECIFICATIONS. 250 khz to 20 GHz RF Analog Signal Generator

PXIe Contents SPECIFICATIONS. 250 khz to 20 GHz RF Analog Signal Generator SPECIFICATIONS PXIe-5654 250 khz to 20 GHz RF Analog Signal Generator These specifications apply to the PXIe-5654 RF Analog Signal Generator with up to 10 GHz or 20 GHz frequency and the PXIe-5696 Amplitude

More information

4-Channel ±10 V, 100 ma, Precision PXI Source Measure Unit

4-Channel ±10 V, 100 ma, Precision PXI Source Measure Unit SPECIFICATIONS PXIe-4141 4-Channel ±10 V, 100 ma, Precision PXI Source Measure Unit These specifications apply to the PXIe-4141. Contents Definitions...1 Conditions... 2 Device Capabilities... 2 SMU Specifications...

More information

4-Channel, ±6 V, 500 ma Precision PXI Source Measure Unit

4-Channel, ±6 V, 500 ma Precision PXI Source Measure Unit SPECIFICATIONS PXIe-4145 4-Channel, ±6 V, 500 ma Precision PXI Source Measure Unit These specifications apply to the PXIe-4145. Contents Definitions...1 Conditions... 2 Device Capabilities... 2 SMU Specifications...

More information

1- or 2-Port, Software-Selectable PXI CAN Interface Module

1- or 2-Port, Software-Selectable PXI CAN Interface Module SPECIFICATIONS PXI-8513 1- or 2-Port, Software-Selectable PXI CAN Interface Module This document lists specifications for the PXI-8513 1-port and 2-port CAN interface module. Definitions Warranted specifications

More information

4-Channel ±10 V, 100 ma, Precision PXI Source Measure Unit

4-Channel ±10 V, 100 ma, Precision PXI Source Measure Unit SPECIFICATIONS PXIe-4141 4-Channel ±10 V, 100 ma, Precision PXI Source Measure Unit These specifications apply to the PXIe-4141. Contents Definitions...1 Conditions... 2 Device Capabilities... 2 SMU Specifications...

More information

4-Channel, ±24 V, 150 ma PXI Source Measure Unit

4-Channel, ±24 V, 150 ma PXI Source Measure Unit SPECIFICATIONS PXIe-4142 4-Channel, ±24 V, 150 ma PXI Source Measure Unit These specifications apply to the PXIe-4142. Contents Definitions...1 Conditions... 2 Device Capabilities... 2 SMU Specifications...

More information

4-Channel, ±24 V, 150 ma Precision PXI Source Measure Unit

4-Channel, ±24 V, 150 ma Precision PXI Source Measure Unit SPECIFICATIONS PXIe-4143 4-Channel, ±24 V, 150 ma Precision PXI Source Measure Unit These specifications apply to the PXIe-4143. Contents Definitions...1 Conditions... 2 Device Capabilities... 2 SMU Specifications...

More information

NI PXI/PXIe Contents. About These Specifications DEVICE SPECIFICATIONS. Quad 2 1 Terminated Multiplexer

NI PXI/PXIe Contents. About These Specifications DEVICE SPECIFICATIONS. Quad 2 1 Terminated Multiplexer DEVICE SPECIFICATIONS NI PXI/PXIe-2542 Quad 2 1 Terminated Multiplexer This document lists specifications for the NI PXI/PXIe-2542 (NI 2542) multiplexer module. All specifications are subject to change

More information

NI PXI/PXIe Contents DEVICE SPECIFICATIONS. 40 A Fault Insertion Unit

NI PXI/PXIe Contents DEVICE SPECIFICATIONS. 40 A Fault Insertion Unit DEVICE SPECIFICATIONS NI PXI/PXIe-2514 40 A Fault Insertion Unit This document lists specifications for the NI PXI/PXIe-2514 (NI 2514) fault insertion unit (FIU) switch module. All specifications are subject

More information

PXI Contents. PXI-2584 Specifications DEVICE SPECIFICATIONS. 300 V CAT II, 600 V CAT I Multiplexers

PXI Contents. PXI-2584 Specifications DEVICE SPECIFICATIONS. 300 V CAT II, 600 V CAT I Multiplexers DEVICE SPECIFICATIONS PXI-2584 300 V CAT II, 600 V CAT I Multiplexers This document lists specifications for the PXI-2584 high-voltage multiplexer switch module. All specifications are subject to change

More information

NI PXI/PXIe Contents DEVICE SPECIFICATIONS. 10 A Fault Insertion Unit

NI PXI/PXIe Contents DEVICE SPECIFICATIONS. 10 A Fault Insertion Unit DEVICE SPECIFICATIONS NI PXI/PXIe-2512 10 A Fault Insertion Unit This document lists specifications for the NI PXI/PXIe-2512 (NI 2512) fault insertion unit (FIU) switch module. All specifications are subject

More information

NI USB Contents DEVICE SPECIFICATIONS. 50 MS/s Bus-Powered USB Oscilloscope

NI USB Contents DEVICE SPECIFICATIONS. 50 MS/s Bus-Powered USB Oscilloscope DEVICE SPECIFICATIONS NI USB-5132 50 MS/s Bus-Powered USB Oscilloscope This document lists specifications for the NI USB-5132 (NI 5132). Unless otherwise noted, these specifications are valid for the following

More information

Related Information Refer to the NI Switches Help for detailed topology information.

Related Information Refer to the NI Switches Help for detailed topology information. SPECIFICATIONS NI PXI-2530B 128-Channel Reed Relay Multiplexer/Matrix This document lists specifications for the NI PXI-2530B 128-channel multiplexer/matrix module (NI 2530B). All specifications are subject

More information

PXIe, 6½-Digit, ±300 V, Onboard 1.8 MS/s Isolated Digitizer,PXI Digital Multimeter

PXIe, 6½-Digit, ±300 V, Onboard 1.8 MS/s Isolated Digitizer,PXI Digital Multimeter SPECIFICATIONS PXIe-4080 PXIe, 6½-Digit, ±300 V, Onboard 1.8 MS/s Isolated Digitizer,PXI Digital Multimeter These specifications apply to the PXIe-4080. Contents Definitions...2 Conditions... 2 DC Voltage

More information

PCI Express, 6½-Digit, ±300 V Digital Multimeter Device

PCI Express, 6½-Digit, ±300 V Digital Multimeter Device SPECIFICATIONS PCIe-4065 PCI Express, 6½-Digit, ±300 V Digital Multimeter Device These specifications apply to the PCIe-4065. Contents Definitions...1 Conditions... 2 DC Specifications... 2 DC System Speed

More information

PXIe Contents SPECIFICATIONS. ±60 V, 3 A System PXI Source Measure Unit. These specifications apply to the PXIe-4138.

PXIe Contents SPECIFICATIONS. ±60 V, 3 A System PXI Source Measure Unit. These specifications apply to the PXIe-4138. SPECIFICATIONS PXIe-4138 ±60 V, 3 A System PXI Source Measure Unit These specifications apply to the PXIe-4138. Contents Definitions...2 Conditions... 2 Cleaning Statement... 2 Device Capabilities... 2

More information

PXIe Contents SPECIFICATIONS. 2-Channel, 60 V, 1 A PXI Programmable Power Supply. These specifications apply to the PXIe-4112.

PXIe Contents SPECIFICATIONS. 2-Channel, 60 V, 1 A PXI Programmable Power Supply. These specifications apply to the PXIe-4112. SPECIFICATIONS PXIe-4112 2-Channel, 60 V, 1 A PXI Programmable Power Supply These specifications apply to the PXIe-4112. Contents Definitions...2 Conditions... 2 Cleaning the Module...2 Device Capabilities...

More information

16-Bit, 120 MS/s, 12 Channel DC/16 Channel AC Receiver Adapter Module

16-Bit, 120 MS/s, 12 Channel DC/16 Channel AC Receiver Adapter Module SPECIFICATIONS NI 5753 16-Bit, 120 MS/s, 12 Channel DC/16 Channel AC Receiver Adapter Module This document lists specifications for the NI 5753 adapter module. Pair these specifications with the specifications

More information

NI roborio. Contents. Processor SPECIFICATIONS. RIO Device for Robotics

NI roborio. Contents. Processor SPECIFICATIONS. RIO Device for Robotics SPECIFICATIONS NI roborio RIO Device for Robotics This document provides specifications for the NI roborio. These specifications are typical for the 0 C to 40 C operating temperature range unless otherwise

More information

USRP Contents. Definitions SPECIFICATIONS. USRP Software Defined Radio Stand-Alone Device

USRP Contents. Definitions SPECIFICATIONS. USRP Software Defined Radio Stand-Alone Device SPECIFICATIONS USRP-2974 USRP Software Defined Radio Stand-Alone Device Contents Definitions...1 Conditions... 2 Controller... 2 FPGA and Baseband... 2 RF...3 Transmitter... 3 Receiver... 3 GPS Disciplined

More information

PXIe Contents SPECIFICATIONS. ±200 V, 1 A System PXI Source Measure Unit. These specifications apply to the PXIe-4136.

PXIe Contents SPECIFICATIONS. ±200 V, 1 A System PXI Source Measure Unit. These specifications apply to the PXIe-4136. SPECIFICATIONS PXIe-4136 ±200 V, 1 A System PXI Source Measure Unit These specifications apply to the PXIe-4136. Contents Definitions...2 Conditions... 2 Cleaning Statement... 2 Device Capabilities...

More information

6½-Digit, ±300 V, 1.8 MS/s Isolated Digitizer Included, PCI Digital Multimeter Device

6½-Digit, ±300 V, 1.8 MS/s Isolated Digitizer Included, PCI Digital Multimeter Device SPECIFICATIONS PCI-4070 6½-Digit, ±300 V, 1.8 MS/s Isolated Digitizer Included, PCI Digital Multimeter Device These specifications apply to the PCI-4070. Contents Definitions...2 Conditions... 2 DC Specifications...

More information

SA1500X. Operating Basics. Cautions DEVICE SPECIFICATIONS. High Impedance Active Probe

SA1500X. Operating Basics. Cautions DEVICE SPECIFICATIONS. High Impedance Active Probe DEVICE SPECIFICATIONS SA1500X High Impedance Active Probe This document lists specifications for the SA1500X active probe, which can contact adjacent square pins to 2.54 mm pitch simultaneously. The housing

More information

PXIe Contents SPECIFICATIONS. ±60 V, 3 A Precision System PXI Source Measure Unit. These specifications apply to the PXIe-4139.

PXIe Contents SPECIFICATIONS. ±60 V, 3 A Precision System PXI Source Measure Unit. These specifications apply to the PXIe-4139. SPECIFICATIONS PXIe-4139 ±60 V, 3 A Precision System PXI Source Measure Unit These specifications apply to the PXIe-4139. Contents Definitions...2 Conditions... 2 Cleaning Statement... 2 Device Capabilities...

More information

80 MHz Bandwidth, 16-Bit PXI Waveform Generator. These specifications apply to the one-channel and two-channel PXIe-5433.

80 MHz Bandwidth, 16-Bit PXI Waveform Generator. These specifications apply to the one-channel and two-channel PXIe-5433. SPECIFICATIONS PXIe-5433 80 MHz Bandwidth, 16-Bit PXI Waveform Generator These specifications apply to the one-channel and two-channel PXIe-5433. Contents Definitions...1 Conditions... 2 Analog Output...2

More information

PXIe Contents SPECIFICATIONS. ±200 V, 1 A Precision System PXI Source Measure Unit. These specifications apply to the PXIe-4137.

PXIe Contents SPECIFICATIONS. ±200 V, 1 A Precision System PXI Source Measure Unit. These specifications apply to the PXIe-4137. SPECIFICATIONS PXIe-4137 ±200 V, 1 A Precision System PXI Source Measure Unit These specifications apply to the PXIe-4137. Contents Definitions...2 Conditions... 2 Cleaning Statement... 2 Device Capabilities...

More information

PXIe, 40 MHz Bandwidth, 16-Bit PXI Waveform Generator. These specifications apply to the one-channel and two-channel PXIe-5423.

PXIe, 40 MHz Bandwidth, 16-Bit PXI Waveform Generator. These specifications apply to the one-channel and two-channel PXIe-5423. SPECIFICATIONS PXIe-5423 PXIe, 40 MHz Bandwidth, 16-Bit PXI Waveform Generator These specifications apply to the one-channel and two-channel PXIe-5423. Contents Definitions...1 Conditions... 2 Analog Output...2

More information

100-SPST (latching), 50-DPST. Refer to the NI Switches Help at ni.com/manuals for detailed topology information.

100-SPST (latching), 50-DPST. Refer to the NI Switches Help at ni.com/manuals for detailed topology information. DEVICE SPECIFICATIONS NI PXI/PXIe-2569 100-Channel SPST Relay Module This document lists specifications for the NI PXI/PXIe-2569 (PXI/PXIe-2569) generalpurpose relay module. All specifications are subject

More information

Related Information Refer to the NI Switches Help for detailed topology information.

Related Information Refer to the NI Switches Help for detailed topology information. DEVICE SPECIFICATIONS NI PXI/PXIe-2532B 512-Crosspoint Matrix This document lists specifications for the NI PXI/PXIe-2532B (NI 2532B) 512-crosspoint matrix. All specifications are subject to change without

More information

PXIe, 80 MHz Bandwidth, 16-Bit PXI Waveform Generator. These specifications apply to the one-channel and two-channel PXIe-5433.

PXIe, 80 MHz Bandwidth, 16-Bit PXI Waveform Generator. These specifications apply to the one-channel and two-channel PXIe-5433. SPECIFICATIONS PXIe-5433 PXIe, 80 MHz Bandwidth, 16-Bit PXI Waveform Generator These specifications apply to the one-channel and two-channel PXIe-5433. Contents Definitions...1 Conditions... 2 Analog Output...2

More information

NI PXI-2521 Specifications 40-Channel DPST Relay Module

NI PXI-2521 Specifications 40-Channel DPST Relay Module NI PXI-2521 Specifications 40-Channel DPST Relay Module This document lists specifications for the NI PXI-2521 general-purpose relay module. All specifications are subject to change without notice. Visit

More information

8-Channel, 12-Bit, 60 MHz PXI Express Oscilloscope

8-Channel, 12-Bit, 60 MHz PXI Express Oscilloscope SPECIFICATIONS PXIe-5105 8-Channel, 12-Bit, 60 MHz PXI Express Oscilloscope Contents Definitions...2 Conditions... 2 Vertical... 3 Analog Input... 3 Impedance and Coupling... 3 Voltage Levels...3 Accuracy...

More information

PXIe Contents SPECIFICATIONS. Precision, 10 fa Sensitivity Low-Current PXI Source Measure Unit. These specifications apply to the PXIe-4135.

PXIe Contents SPECIFICATIONS. Precision, 10 fa Sensitivity Low-Current PXI Source Measure Unit. These specifications apply to the PXIe-4135. SPECIFICATIONS PXIe-4135 Precision, 10 fa Sensitivity Low-Current PXI Source Measure Unit These specifications apply to the PXIe-4135. Contents Definitions...2 Conditions... 2 Cleaning Statement... 2 Device

More information

PXI Contents SPECIFICATIONS. 8-Channel, 12-Bit, 60 MHz PXI Oscilloscope

PXI Contents SPECIFICATIONS. 8-Channel, 12-Bit, 60 MHz PXI Oscilloscope SPECIFICATIONS PXI-5105 8-Channel, 12-Bit, 60 MHz PXI Oscilloscope Contents Definitions...2 Conditions... 2 Vertical... 3 Analog Input... 3 Impedance and Coupling... 3 Voltage Levels...3 Accuracy... 3

More information

Current ON state current ma minimum, 6 ma typical, 10 ma maximum OFF state current ma maximum

Current ON state current ma minimum, 6 ma typical, 10 ma maximum OFF state current ma maximum DEVICE SPECIFICATIONS NI 6624 This document lists the specifications for the NI PCI/PXI-6624 device. These specifications are typical at 25 C unless otherwise noted. Refer to the NI 6624 User Manual for

More information

PCI Contents SPECIFICATIONS. 8-Channel, 12-Bit, 60 MHz PCI Oscilloscope Device

PCI Contents SPECIFICATIONS. 8-Channel, 12-Bit, 60 MHz PCI Oscilloscope Device SPECIFICATIONS PCI-5105 8-Channel, 12-Bit, 60 MHz PCI Oscilloscope Device Contents Definitions...2 Conditions... 2 Vertical... 3 Analog Input... 3 Impedance and Coupling... 3 Voltage Levels...3 Accuracy...

More information

NI PXI-2520 Specifications 80-Channel SPST Relay Module

NI PXI-2520 Specifications 80-Channel SPST Relay Module NI PXI-2520 Specifications 80-Channel SPST Relay Module This document lists specifications for the NI PXI-2520 general-purpose relay module. All specifications are subject to change without notice. Visit

More information

R Series for USB Multifunction RIO with Kintex-7 70T FPGA. may impair the protection the NI USB-7855R provides.

R Series for USB Multifunction RIO with Kintex-7 70T FPGA. may impair the protection the NI USB-7855R provides. SPECIFICATIONS NI USB-7855R R Series for USB Multifunction RIO with Kintex-7 70T FPGA This document contains the specifications for the NI USB-7855R. Specifications are typical at 25 C unless otherwise

More information

16 AI (16-Bit, 250 ks/s), 4 DI, 4 DO USB Multifunction I/O Device

16 AI (16-Bit, 250 ks/s), 4 DI, 4 DO USB Multifunction I/O Device SPECIFICATIONS USB-6210 16 AI (16-Bit, 250 ks/s), 4 DI, 4 DO USB Multifunction I/O Device Definitions Warranted specifications describe the performance of a model under stated operating conditions and

More information

mmwave Transceiver System

mmwave Transceiver System SPECIFICATIONS mmwave Transceiver System 2 GHz Bandwidth mmwave Transceiver System Contents Definitions...1 Conditions... 2 System Performance and Characteristics...2 24.25 GHz to 33.4 GHz mmwave Transceiver

More information

Input Characteristics. Measurement Range. SPECIFICATIONS NI PXIe-4357

Input Characteristics. Measurement Range. SPECIFICATIONS NI PXIe-4357 SPECIFICATIONS NI PXIe-4357 This document lists specifications for the NI PXIe-4357 module. These specifications are typical for the range of 0 C to 55 C unless otherwise stated. The system must be allowed

More information

NI PXI-2797 Specifications 40 GHz 6 1 Terminated 50 Ω Multiplexer

NI PXI-2797 Specifications 40 GHz 6 1 Terminated 50 Ω Multiplexer NI PXI-2797 Specifications 40 GHz 6 1 Terminated 50 Ω Multiplexer This document lists specifications for the NI PXI-2797 terminated multiplexer module. All specifications are subject to change without

More information

Power Amplifier. Input Characteristics. SPECIFICATIONS NI PXIe-4610 Power Amplifier. Signal Range

Power Amplifier. Input Characteristics. SPECIFICATIONS NI PXIe-4610 Power Amplifier. Signal Range SPECIFICATIONS NI PXIe-4610 Power Amplifier This document lists specifications for the NI PXIe-4610 Power Amplifier. These specifications are typical at 25 ºC unless otherwise stated. The operating range

More information

100 MHz, 32-Channel, 5 V PXI Digital Waveform Instrument

100 MHz, 32-Channel, 5 V PXI Digital Waveform Instrument SPECIFICATIONS PXI-6542 100 MHz, 32-Channel, 5 V PXI Digital Waveform Instrument These specifications apply to the PXI-6542 with 1 MBit, 8 MBit, and 64 MBit of memory per channel. Contents Hot Surface

More information

NI PXI/PXIe-2529 Specifications

NI PXI/PXIe-2529 Specifications NI PXI/PXIe-2529 Specifications 128-Crosspoint Relay Matrix This document lists specifications for the NI PXI/PXIe-2529 (NI 2529) matrix module. All specifications are subject to change without notice.

More information

R Series for USB Multifunction RIO with Kintex-7 70T FPGA

R Series for USB Multifunction RIO with Kintex-7 70T FPGA SPECIFICATIONS NI USB-7845R OEM R Series for USB Multifunction RIO with Kintex-7 70T FPGA This document contains the specifications for the NI USB-7845R OEM device. Specifications are typical at 25 C unless

More information

PXI Contents SPECIFICATIONS. 1 GHz Bandwidth, 2 GS/s, 8-Bit PXI Oscilloscope

PXI Contents SPECIFICATIONS. 1 GHz Bandwidth, 2 GS/s, 8-Bit PXI Oscilloscope SPECIFICATIONS PXI-5154 1 GHz Bandwidth, 2 GS/s, 8-Bit PXI Oscilloscope Contents Definitions...2 Conditions... 2 Vertical... 3 Analog Input (Channel 0 and Channel 1)... 3 Impedance and Coupling... 3 Voltage

More information

Specifications are typical and valid from -40 C to +85 C unless otherwise noted. Galvanic isolation between channels and to chassis

Specifications are typical and valid from -40 C to +85 C unless otherwise noted. Galvanic isolation between channels and to chassis SPECIFICATIONS FD-11603 8-Channel Voltage Input Device for FieldDAQ Conditions Specifications are typical and valid from -40 C to +85 C unless otherwise noted. Input Characteristics Number of channels

More information

Analog Characteristics

Analog Characteristics SPECIFICATIONS NI PXIe-4322 This document lists specifications for the NI PXIe-4322 module. These specifications are typical for the range of 0 C to 55 C unless otherwise stated. The system must be allowed

More information

PXI Contents SPECIFICATIONS. 6½-Digit, ±300 V, Onboard 1.8 MS/s Isolated Digitizer, L and C Measurement Support, PXI Digital Multimeter

PXI Contents SPECIFICATIONS. 6½-Digit, ±300 V, Onboard 1.8 MS/s Isolated Digitizer, L and C Measurement Support, PXI Digital Multimeter SPECIFICATIONS PXI-4072 6½-Digit, ±300 V, Onboard 1.8 MS/s Isolated Digitizer, L and C Measurement Support, PXI Digital Multimeter These specifications apply to the PXI-4072. Contents Definitions...2 Conditions...

More information

PXIe Contents SPECIFICATIONS. 500 MHz, 2.5 GS/s, 10-Bit PXI Express Oscilloscope

PXIe Contents SPECIFICATIONS. 500 MHz, 2.5 GS/s, 10-Bit PXI Express Oscilloscope SPECIFICATIONS PXIe-5160 500 MHz, 2.5 GS/s, 10-Bit PXI Express Oscilloscope Contents Definitions...2 Conditions... 2 Vertical... 3 Analog Input... 3 Impedance and Coupling... 3 Voltage Levels...4 Accuracy...

More information

PXI Contents SPECIFICATIONS. 300 MHz Bandwidth, 2 GS/s, 8-Bit PXI Oscilloscope

PXI Contents SPECIFICATIONS. 300 MHz Bandwidth, 2 GS/s, 8-Bit PXI Oscilloscope SPECIFICATIONS PXI-5152 300 MHz Bandwidth, 2 GS/s, 8-Bit PXI Oscilloscope Contents Definitions...2 Conditions... 2 Vertical... 3 Analog Input (Channel 0 and Channel 1)... 3 Impedance and Coupling... 3

More information

NI PXI/PXIe-2540 Specifications

NI PXI/PXIe-2540 Specifications NI PXI/PXIe-254 Specifications 35 MHz 8 9 5 Ω Matrix This document lists specifications for the NI PXI/PXIe-254 (NI 254) matrix module. All specifications are subject to change without notice. Visit ni.com/manuals

More information

This document lists the specifications for the NI PXIe-5185 (NI 5185) 3 GHz digitizer.

This document lists the specifications for the NI PXIe-5185 (NI 5185) 3 GHz digitizer. DEVICE SPECIFICATIONS NI PXIe-5185 12.5 GS/s, 8-Bit Digitizer This document lists the specifications for the NI PXIe-5185 (NI 5185) 3 GHz digitizer. Contents NI PXIe-5185 Specifications... 1 Vertical...

More information

This document lists the specifications for the NI PXIe-5186 (NI 5186) 5 GHz digitizer.

This document lists the specifications for the NI PXIe-5186 (NI 5186) 5 GHz digitizer. DEVICE SPECIFICATIONS NI PXIe-5186 12.5 GS/s, 8-Bit Digitizer This document lists the specifications for the NI PXIe-5186 (NI 5186) 5 GHz digitizer. Contents NI PXIe-5186 Specifications... 1 Vertical...

More information

R Series Reconfigurable I/O Module (AI, AO, DIO) for PXI Express, 8 AI, 8 AO, 48 DIO, 500 ks/s AI, Kintex-7 160T FPGA

R Series Reconfigurable I/O Module (AI, AO, DIO) for PXI Express, 8 AI, 8 AO, 48 DIO, 500 ks/s AI, Kintex-7 160T FPGA SPECIFICATIONS NI PXIe-7846R R Series Reconfigurable I/O Module (AI, AO, DIO) for PXI Express, 8 AI, 8 AO, 48 DIO, 500 ks/s AI, Kintex-7 160T FPGA This document contains the specifications for the NI PXIe-7846R.

More information

24-Bit, 6-Channel, 1.25 MS/s/ch PXI Analog Input Module

24-Bit, 6-Channel, 1.25 MS/s/ch PXI Analog Input Module SPECIFICATIONS PXIe-4481 24-Bit, 6-Channel, 1.25 MS/s/ch PXI Analog Input Module Definitions Warranted specifications describe the performance of a model under stated operating conditions and are covered

More information

NI PXI/PXIe-2541 Specifications 300 MHz Ω Matrix

NI PXI/PXIe-2541 Specifications 300 MHz Ω Matrix NI PXI/PXIe-2541 Specifications 3 MHz 8 12 5 Ω Matrix This document lists specifications for the NI PXI/PXIe-2541 (NI 2541) matrix module. All specifications are subject to change without notice. Visit

More information

PXIe Contents SPECIFICATIONS. 1.5 GHz, 5 GS/s, 10-Bit PXI Express Oscilloscope

PXIe Contents SPECIFICATIONS. 1.5 GHz, 5 GS/s, 10-Bit PXI Express Oscilloscope SPECIFICATIONS PXIe-5162 1.5 GHz, 5 GS/s, 10-Bit PXI Express Oscilloscope Contents Definitions...2 Conditions... 2 Vertical... 3 Analog Input... 3 Impedance and Coupling... 3 Voltage Levels...4 Accuracy...

More information

PXIe Contents SPECIFICATIONS. IF Digitizer

PXIe Contents SPECIFICATIONS. IF Digitizer SPECIFICATIONS PXIe-5624 IF Digitizer Contents Definitions...2 Conditions... 2 Modes of Operation... 2 Frequency...3 Internal Frequency Reference... 3 Frequency Reference/ADC Sample Clock Input (CLK IN)...

More information

NI 2865A 0.3 A Matrix Cards for NI SwitchBlock

NI 2865A 0.3 A Matrix Cards for NI SwitchBlock SPECIFICATIONS NI 2865A 0.3 A Matrix Cards for NI SwitchBlock This document lists specifications for the NI 2865A matrix relay cards. All specifications are subject to change without notice. Visit ni.com/manuals

More information

NI 9220 DATASHEET. 16 AI, ±10 V, 16 Bit, 100 ks/s/ch Simultaneous. DSUB or push-in springterminal. 250 Vrms, CAT II, channelto-earth

NI 9220 DATASHEET. 16 AI, ±10 V, 16 Bit, 100 ks/s/ch Simultaneous. DSUB or push-in springterminal. 250 Vrms, CAT II, channelto-earth DATASHEET NI 9220 16 AI, ±10 V, 16 Bit, 100 ks/s/ch Simultaneous DSUB or push-in springterminal connectivity 250 Vrms, CAT II, channelto-earth isolation (spring terminal); 60 VDC, CAT I, channel-to-earth

More information

PXIe Contents SPECIFICATIONS. 125 MHz, 2-Channel, 8-Bit, PXI Express Oscilloscope

PXIe Contents SPECIFICATIONS. 125 MHz, 2-Channel, 8-Bit, PXI Express Oscilloscope SPECIFICATIONS PXIe-5114 125 MHz, 2-Channel, 8-Bit, PXI Express Oscilloscope Contents Definitions...2 Conditions... 2 Vertical... 3 Analog Input... 3 Impedance and Coupling... 3 Voltage Levels...3 Accuracy...

More information

PXI Contents SPECIFICATIONS. 100 MHz, 100 MS/s, 14-Bit PXI Oscilloscope

PXI Contents SPECIFICATIONS. 100 MHz, 100 MS/s, 14-Bit PXI Oscilloscope SPECIFICATIONS PXI-5122 100 MHz, 100 MS/s, 14-Bit PXI Oscilloscope Contents Definitions...2 Conditions... 2 Vertical... 2 Analog Input... 2 Impedance and Coupling... 3 Voltage Levels...3 Accuracy... 3

More information

R Series Reconfigurable I/O Module (AI, AO, DIO) for PXI Express, 6 AI, 18 AO, 48 DIO, 1 MS/s AIO, 512 MB DRAM, Kintex-7 325T FPGA

R Series Reconfigurable I/O Module (AI, AO, DIO) for PXI Express, 6 AI, 18 AO, 48 DIO, 1 MS/s AIO, 512 MB DRAM, Kintex-7 325T FPGA SPECIFICATIONS NI PXIe-7868R R Series Reconfigurable I/O Module (AI, AO, DIO) for PXI Express, 6 AI, 18 AO, 48 DIO, 1 MS/s AIO, 512 MB DRAM, Kintex-7 325T FPGA This document contains the specifications

More information

NI PXI-2557 Specifications

NI PXI-2557 Specifications NI PXI-2557 Specifications 2.5 GHz 75 8 x 1 Multiplexer (SP8T) This document lists specifications for the NI PXI-2557 multiplexer module. All specifications are subject to change without notice. Visit

More information

DEVICE SPECIFICATIONS NI PXIe Ch, 24-bit, 25.6 ks/s Simultaneous AC LVDT Input Module

DEVICE SPECIFICATIONS NI PXIe Ch, 24-bit, 25.6 ks/s Simultaneous AC LVDT Input Module DEVICE SPECIFICATIONS NI PXIe-4340 4 Ch, 24-bit, 25.6 ks/s Simultaneous AC LVDT Input Module This document lists specifications for the NI PXIe-4340 simultaneous AC LVDT input module. All specifications

More information

SCXI MHz Quad 8x1 50 Ω Multiplexer

SCXI MHz Quad 8x1 50 Ω Multiplexer SPECIFICATIONS SCXI -1193 500 MHz Quad 50 Ω Multiplexer This document lists specifications for the SCXI-1193 multiplexer module. All specifications are subject to change without notice. Visit ni.com/manuals

More information

NI 9770 DATASHEET. 30 khz to 100 MHz, 50 Ω, AC Coupled RF Receiver Module

NI 9770 DATASHEET. 30 khz to 100 MHz, 50 Ω, AC Coupled RF Receiver Module DATASHEET NI 9770 30 khz to 100 MHz, 50 Ω, AC Coupled RF Receiver Module 1-channel, 320 ks/s Support for RF emissions measurements from 30 khz to 100 MHz Software-selectable bandwidth from 3.2 khz to 256

More information

NI 9216 DATASHEET. 8 RTD, 0 Ω to 400 Ω, 24 Bit, 400 S/s Aggregate, PT100

NI 9216 DATASHEET. 8 RTD, 0 Ω to 400 Ω, 24 Bit, 400 S/s Aggregate, PT100 DATASHEET NI 9216 8 RTD, 0 Ω to 400 Ω, 24 Bit, 400 S/s Aggregate, PT100 DSUB or spring-terminal connectivity 50 Hz/60 Hz noise rejection 250 Vrms, CAT II, channel-to-earth isolation (spring terminal);

More information

GETTING STARTED GUIDE NI Port DeviceNet Module

GETTING STARTED GUIDE NI Port DeviceNet Module GETTING STARTED GUIDE NI 9882 1-Port DeviceNet Module This document explains how to connect to the NI 9882. The NI 9882 module requires the latest NI-DeviceNet software to be installed. The latest version

More information

PXI Contents SPECIFICATIONS. 125 MHz, 2-Channel, 8-Bit PXI Oscilloscope

PXI Contents SPECIFICATIONS. 125 MHz, 2-Channel, 8-Bit PXI Oscilloscope SPECIFICATIONS PXI-5114 125 MHz, 2-Channel, 8-Bit PXI Oscilloscope Contents Definitions...2 Conditions... 2 Vertical... 3 Analog Input... 3 Impedance and Coupling... 3 Voltage Levels...3 Accuracy... 4

More information