Wirewound Rheostats and Potentiometers Graded Windings, Ganged Assemblies
|
|
- Horatio Mills
- 6 years ago
- Views:
Transcription
1 Wirewound Rheostats and Potentiometers raded Windings, anged Assemblies FEATURES Duo, trio or quattro configurations DATA REQUIRED TO DEFINE A UNIT a: Ohmic value of the current load in series with the rheostat b: Supply voltage of the rheostat + series load c: Ohmic value of rheostat d: Maximum current when the rheostat is in short circuit position e: Current when the rheostat is set to maximum ohmic value f: Resistance variation law as a function of mechanical travel To define a graded winding unit a, b and c; or c, d and e or g has to be established. APPLICATION EXAMPLES Potentiometer mode The following data has to be established: - Potentiometer supply voltage U - Ohmic value of the controlled current load Note If the power to be controlled is small, a linear, variation law rheostat can be used U Ohmic value: R = -- and 2 I = ; in such case the output current is 5 Control of lamps The parameters to be established are: - Light flux variation required: Linear from 100 % to 1 % log variation from 100 % to 4 % or from 100 % to 20 % - Lamp supply voltage - Lamp power range I 6U = RHEOSTATS AND POTENTIOMETERS WITH RADED WINDIN: RTS max. current When the ration exceeds 2, a graded unit may min. current min. current enable a smaller sized unit to be used than an equivalent linear law unit for the same maximum current. raded windings can also avoid the use of twin units. Linear relationships are achievable between the variable parameters being controlled and the rheostat command shaft. All RT size rheostats are available with graded windings except the RT12 size. The resistive wire is protected by a specially formulated enamel. Mechanical and environmental characteristics are identical to the RT series. ANED ASSEMBLIES Rheostats may be ganged mechanically in the following styles: 2 ganged units DUO 3 ganged units TRIO 4 ganged units QUATTRO The RT12 unit is not suitable for ganged assembly. anged assemblies may comprise: - Similar sized units, where the ohmic values may be different - Various sized units where the unit at the top end of the command shaft can be of smaller size COMMAND SYSTEM All units with common command: Code CU Shaft locking devices as an option: Code DBA (factory assembled) Concentric shafts: Code CC Available for double ganged units only: DUO The shaft locking device and double mini switch cannot be fitted to concentric shaft Command knobs as an option: Code JF for standard shaft, code JFP - FSP for concentric shafts SPECIAL FEATURES For any special features such as graded windings, centertappings, etc. We would be pleased to receive the details of your particular requirements. Revision: 08-Aug-13 1 Document Number: THIS DOCUMENT IS SUBJECT TO CHANE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
2 DIMENSIONS in millimeters FEATURES Mechanical, electrical, and environmental features are similar to the RT series document numbers, 50024, 50025, 50026, 50027, 50028, 50029, F K Connection DIMENSIONS SERIES TYPE A B C D E F H J Ø H H Duo M FRT Trio M TRIO C MRT Quattro M QUARTO 5 Notes Duo 2 ganged units Trio 3 ganged units Quattro 4 ganged units C C MRT PANEL CUT-OUT E PANEL CUT-OUT DUO - TRIO - QUATTRO B Mounting Plane A + 2 CRT PANEL CUT-OUT J P D Type L M Ø N M5 7 7 CONCENTRIC SHAFT (1) SERIES TYPE Ø P Ø Q R S Duo Note (1) 2 ganged units only Ø 12 CONCENTRIC SHAFT S Ø N M ØQ Ø P L R Revision: 08-Aug-13 2 Document Number: THIS DOCUMENT IS SUBJECT TO CHANE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
3 ELECTRICAL DIARAM (typical use) Single rheostat connected Single potentiometer connected Double potentiometer series connected, load in parallel Triple rheostat series connected Double rheostat parallel connected, load in series Double potentiometer parallel connected, load in series Triple rheostat connected, used for three phase current regulator Double bridge Double potentiometer parallel connected, load in parallel Triple potentiometer connected, used for three phase current regulator MARKIN raded winding units: RTS trademark, series, style, number of graded, windings, ohmic value (in or k), tolerance (in %), maximum current (in A), manufacturing date anged units: : Duo, Trio, Quattro trademark, series, style, the relative position of each unit in the assembly. CRT 1 st unit (command knob end), MRT 2 nd and/or 3 rd unit, FRT last unit, ohmic value (in or k), tolerance (in %), maximum current (in A), manufacturing date Revision: 08-Aug-13 3 Document Number: THIS DOCUMENT IS SUBJECT TO CHANE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
4 ORDERIN INFORMATION DUO 25 CU 2 x 7 10 % e SERIES TYPE STYLE COMMAND SHAFT OHMIC VALUE TOLERANCE LEAD (Pb)-FREE Trio Quattro Common Shaft CU Concentric Shaft CC LOBAL PART NUMBER INFORMATION T R T C U K LOBAL MODEL DRT (duo) TRT (trio) QRT (quattro) SIE COMMAND SHAFT OHMIC VALUE TOLERANCE PACKAIN SPECIAL CU = Common shaft CC = Concentric shaft The first three digits are significant figures and the last digit specifies the number of zeros to follow. R designates decimal point = 20 k 4700 = R0 = = 100 K = 10 % B = Box BO1 As applicable Ex.: DXxx Revision: 08-Aug-13 4 Document Number: THIS DOCUMENT IS SUBJECT TO CHANE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
5 Legal Disclaimer Notice Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, Vishay ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer s technical experts. Product specifications do not expand or otherwise modify Vishay s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners VISHAY INTERTECHNOLOY, INC. ALL RIHTS RESERVED Revision: 08-Feb-17 1 Document Number: 91000
Single Phase Bridge Rectifier, 2 A
Single Phase Bridge Rectifier, 2 A FEATURES Suitable for printed circuit board mounting Compact construction High surge current capability Material categorization: for definitions of compliance please
More informationFully Sealed Container 12 mm Square or Round Single-Turn Cermet Trimmer
Fully Sealed Container 12 mm Square or Round Single-Turn Cermet Trimmer The trimming potentiometers T12 and T13 fully meet the requirements of CECC 41 100. The use of a cermet track combined with sealing
More informationSingle Phase Rectifier Bridge, 1.9 A
Single Phase Rectifier Bridge, 1.9 A PRIMARY CHARACTERISTICS I O 1.9 A V RRM 5 V to 1 V Package Circuit configuration Single phase bridge FEATURES Suitable for printed circuit board mounting Leads on standard
More informationKnob Potentiometer FEATURES. P16NP P16NM Panel Cutout. Thickness nut 2 mm washer 1.5 mm. Panel sealing ring 12 wrench Thread M10 x
Knob Potentiometer P6, PA6 DESIGN SUPPORT TOOLS click logo to get started FEATURES Test according to CECC 4000 or IEC 60393- P6 - version for professional and industrial applications (cermet) W at 40 C
More informationSingle Phase Rectifier Bridge, 1.2 A
Single Phase Rectifier Bridge, 1.2 A FEATURES VS-1KAB-E Series Ease of assembly, installation, inventory High surge rating Compact Material categorization: for definitions of compliance please see www.vishay.com/doc?99912
More informationKnob Potentiometer with Switch
Knob Potentiometer with Switch, The is a revolutionary concept in panel mounted potentiometers. This unique design consists of a knob driving and incorporating a cermet potentiometer. Only the mounting
More informationFully Sealed Container Cermet Potentiometer Professional Grade
Fully Sealed Container Cermet Potentiometer Professional Grade T Q O QUICK REFERENCE DATA Multiple module Switch module Detent module Special electrical laws No n/a n/a A: linear, L: logarithmic, F: reverse
More informationAluminum Electrolytic Capacitors Power Ultra High Ripple Current Snap-In for Solar
Aluminum Electrolytic Capacitors Power Ultra High Ripple Current Snap-In for Solar FEATURES Long useful life: 6000 h at +105 C Specified for 500 V, 50 C operation High ripple current capability High reliability
More informationSingle Phase Rectifier Bridge, 3 A, 6 A
S-, S- Series Single Phase Rectifier Bridge, 3 A, 6 A FEATURES Suitable for printed circuit board or chassis mounting Compact construction High surge current capability Material categorization: for definitions
More informationSurface Mount Ceramic Chip Antennas for 2.4 GHz
Surface Mount Ceramic Chip Antennas for 2.4 GHz chip antenna The VJ5106W240 series are small form-factor, high-performance chip-antennas designed to be used in wireless, bluetooth and ISM band 2.4 GHz.
More informationHigh Efficiency Blue LED in Ø 3 mm Tinted Diffused Package
High Efficiency Blue LED in Ø 3 mm Tinted Diffused Package DESCRIPTION 19222 This device has been redesigned in 1998 replacing SiC by GaN technology to meet the increasing demand for high efficiency blue
More informationSingle Phase Rectifier Bridge, 2 A
Single Phase Rectifier Bridge, 2 A 2KBP Series FEATURES Suitable for printed circuit board mounting Compact construction RoHS COMPLIANT D-44 PRODUCT SUMMARY I O V RRM 2 A 50 to 1000 V High surge current
More informationPower Resistors Cooled by Auxiliary Heatsink (Not Supplied) Thick Film Technology
Power Resistors Cooled by Auxiliary Heatsink (Not Supplied) Thick Film Technology FEATURES Cold system without external radiation High power / volume ratio Non-inductive Screw-on or fast-on outputs DESIGN
More informationVersatile Planar Transformer
Versatile Planar Transformer QUICK REFERENCE DATA Type Transformer Size (L x W x H) 40 mm x 35 mm x 2 mm Terminals SMD or through holes Power Up to 220 W Frequency range 50 khz to 400 khz Inductance range
More informationFully Sealed Container Cermet Potentiometers Submarine Applications
Fully Sealed Container Cermet Potentiometers Submarine Applications FEATURES High power rating 1.5 W at 70 C Stainless steel shaft and bushing to endure sea salt water immersion Fully sealed IP68 on panel
More informationSingle Turn Servo Mount Hall Effect Sensor in Size 05 (12.7 mm)
Single Turn Servo Mount Hall Effect Sensor in Size 05 (12.7 mm QUICK REFERENCE DATA Sensor type ROTATIONAL, single turn hall effect Output type Wires Market appliance Professional Dimensions ½" (12.7 mm
More informationHigh Intensity LED in Ø 3 mm Tinted Diffused Package
High Intensity LED in Ø 3 mm Tinted Diffused Package DESCRIPTION 19222 This device has been designed to meet the increasing demand for AlInGaP technology. It is housed in a 3 mm diffused plastic package.
More informationRotational Position Sensor, Kit Type, Hall Effect Technology
Rotational Position Sensor, Kit Type, Hall Effect Technology QUICK REFERENCE DATA Sensor type Kit rotational, hall effect Output type Wires Market appliance Industrial Dimensions 48 mm x 43 mm x 12 mm
More informationAnalog Rectilinear Displacement Sensor
Analog Rectilinear Displacement Sensor FEATURES Conductive plastic potentiometer technology. Infinite resolution Anodized light alloy housing Precious metal multi-contact wiper Stainless steel floating
More informationCeramic Disc Capacitors Class 2, 500 V DC, 1 kv DC, General Purpose
Ceramic Disc Capacitors Class 2, 500 V DC, 1 kv DC, General Purpose FEATURES High capacitance in small size Kinked (preferred) or straight leads Compliant to RoHS Directive 2011/65/EU APPLICATIONS Bypassing
More informationAluminum Electrolytic Capacitors Power Miniaturized General Purpose - Snap-In
Aluminum Electrolytic Capacitors Power Miniaturized General Purpose - Snap-In FEATURES Useful life: 2000 h at +105 C, > 5000 h at +85 C Voltage range from 16 V to 100 V Polarized aluminum electrolytic
More informationThin Film Bar MOS Capacitors
Thin Film Bar MOS Capacitors FEATURES Robust MOS construction Allows for multiple wire bonds. At the lowest values, case A will accept 7 bonds and case B will accept 15. Low D, high Q Excellent load life
More informationFully Sealed Potentiometer Professional Grade
Fully Sealed Potentiometer Professional Grade PE0 QUICK REFERENCE DATA Multiple module No Switch module n/a Detent module Yes Special electrical laws A: linear, L:, F: reverse Sealing level IP 67 Lifespan
More informationInsulated Precision Wirewound Resistors Axial Leads
Insulated Precision Wirewound Resistors Axial Leads In wirewound precision resistors, the series holds a leading position in professional applications whenever an excellent stability of the ohmic value
More informationVS-1N1183, VS-1N3765, VS-1N1183A, VS-1N2128A Series Power Silicon Rectifier Diodes, (Stud Version), 35 A, 40 A, 60 A
Power Silicon Rectifier Diodes, (Stud Version), 35 A, 4 A, A FEATURES Low leakage current series Good surge current capability up to A Material categorization: for definitions of compliance please see
More informationThrottle Position Sensor in Hall Effect Technology Hollow and D-Shaft Versions
Throttle Position Sensor in Hall Effect Technology Hollow and D-Shaft Versions QUICK REFERENCE DATA Sensor type ROTATIONAL, single turn hall effect Output type Wires Market appliance Industrial Dimensions
More informationLow Current LED in Ø 5 mm Tinted Diffused Package
TLLR54., TLLY54., TLLG54. Low Current LED in Ø 5 mm Tinted Diffused Package 9223 PRODUCT GROUP AND PACKAGE DATA Product group: LED Package: 5 mm Product series: low current Angle of half intensity: ± 25
More informationFully Sealed Container Cermet Potentiometers Submarine Applications
FEATURES High power rating W at 70 C Stainless steel shaft and bushing to endure sea salt water immersion Fully sealed IP68 on panel Tight temperature coefficient (± 75 ppm/ C typical) Compliant to RoHS
More informationSingle Phase Rectifier Bridge, 1.9 A
Single Phase Rectifier Bridge, 1.9 A VS- Series PRODUCT SUMMARY I O V RRM Package Circuit 1.9 A 1 V to 1 V Single phase bridge FEATURES Suitable for printed circuit board mounting Leads on standard 2.54
More informationHigh Intensity Red Low Current 7-Segment Display
High Intensity Red Low Current 7-Segment Display DESCRIPTION 19237 This series defines a new standard for low current displays. It is a single digit 7-segment LED display utilizing AllnGaP technology in
More informationPower Resistors for Mounting onto a Heatsink Thick Film Technology
Power Resistors for Mounting onto a Heatsink Thick Film Technology FEATURES 1% tolerance available High power rating = 200 W Wide ohmic value range = 0.046 to 1 M Non inductive Easy mounting Low thermal
More informationSmall Signal Switching Diode, Dual
Small Signal Switching Diode, Dual 3 1 2 18108_1 DESIGN SUPPORT TOOLS click logo to get started FEATURES Silicon epitaxial planar diode Fast switching dual diode with common cathode AEC-Q101 qualified
More informationPower Resistor, for Mounting onto a Heatsink Thick Film Technology
Power Resistor, for Mounting onto a Heatsink Thick Film Technology FEATURES 5 W to 50 W High power rating DESIGN SUPPORT TOOLS Models Available click logo to get started High overload capabilities up to
More informationSilicon PIN Photodiode, RoHS Compliant
BPW83 DESCRIPTION 94 8490 BPW83 is a PIN photodiode with high speed and high radiant sensitivity in a black, side view plastic package with daylight blocking filter. Filter bandwidth is matched with 870
More informationSingle Phase Rectifier Bridge, 2 A
Single Phase Rectifier Bridge, 2 A 2KBP Series FEATURES Suitable for printed circuit board mounting Compact construction RoHS COMPLIANT D-44 PRODUCT SUMMARY I O V RRM 2 A 50 to 1000 V High surge current
More informationSilicon PIN Photodiode
Silicon PIN Photodiode DESCRIPTION 94 8632 is a PIN photodiode with high speed and high radiant sensitivity in a clear, side view plastic package. It is sensitive to visible and near infrared radiation.
More informationSingle-Line ESD Protection in SOT-23
Single-Line ESD Protection in 3 1 2 20421 MARKING (example only) XX YYY XX 20512 YYY = type code (see table below) XX = date code 20357 1 FEATURES Single-line ESD-protection device ESD-protection acc.
More informationVS-1N1183, VS-1N3765, VS-1N1183A, VS-1N2128A Series Power Silicon Rectifier Diodes, (Stud Version), 35 A, 40 A, 60 A
Power Silicon Rectifier Diodes, (Stud Version), 35 A, 40 A, A FEATURES Low leakage current series Good surge current capability up to 00 A Material categorization: for definitions of compliance please
More informationSilicon NPN Phototransistor
Silicon NPN Phototransistor DESCRIPTION 94 8391 BPW96 is a silicon NPN phototransistor with high radiant sensitivity in clear, T-1¾ plastic package. It is sensitive to visible and near infrared radiation.
More informationBicolor Symbol LED in 2.5 mm x 5 mm Untinted Top-Diffused Package
Bicolor Symbol LED in 2.5 mm x 5 mm Untinted Top-Diffused Package TLSV5 96496 PRODUCT GROUP AND PACKAGE DATA Product group: LED Package: 2.5 mm x 5 mm symbol Product series: bicolor Angle of half intensity:
More informationSmall Signal Switching Diode
Small Signal Switching Diode 2 DESIGN SUPPORT TOOLS click logo to get started 3 FEATURES Silicon epitaxial planar diode Fast switching diode in case SOT-23, especially suited for automatic insertion AEC-Q
More informationSilicon NPN Phototransistor
Silicon NPN Phototransistor DESCRIPTION 285 BPW85 is a silicon NPN phototransistor with high radiant sensitivity in clear, T- plastic package. It is sensitive to visible and near infrared radiation. FEATURES
More informationINT-A-PAK Half Bridge IGBT (Standard Speed IGBT), 200 A
INT-A-PAK Half Bridge IGBT (Standard Speed IGBT), 2 A VS-GA2HSS1PbF INT-A-PAK PRIMARY CHARACTERISTICS V CES V I C DC 8 A V CE(on) at 2 A, 25 C 1.13 V Speed DC to 1 khz Package INT-A-PAK Circuit configuration
More informationHEXFRED Ultrafast Diodes, 300 A (INT-A-PAK Power Modules)
HEXFRED Ultrafast Diodes, 300 A (INT-A-PAK Power Modules) INT-A-PAK PRIMARY CHARACTERISTICS V R 1200 V V F (typical) at 300 A at 2.18 V t rr (typical) at 45 A 233 ns I F(DC) at T C 300 A at 60 C Package
More informationSilicon PIN Photodiode
Silicon PIN Photodiode DESCRIPTION is a silicon PIN photodiode with high radiant sensitivity in clear, T-1 plastic package. It is sensitive to visible and near infrared radiation. FEATURES Package type:
More informationSmall Signal Fast Switching Diode
DESIGN SUPPORT TOOLS click logo to get started Small Signal Fast Switching Diode FEATURES Silicon epitaxial planar diode Fast switching diode AEC-Q qualified available (part number on request) Base P/N-G3
More informationEnhanced isocink+ Bridge Rectifiers
Enhanced isocink+ Bridge Rectifiers - ~ ~ + isocink+ Case Style BU PRIMARY CHARACTERISTICS Package BU I F(AV) 5 A V RRM 6 V, 8 V, V I FSM 2 A I R 5 μa V F at I F = 7.5 A.87 V T J max. 5 C Circuit configuration
More informationP-Channel 30-V (D-S), MOSFET
SUD5P3- P-Channel 3-V (D-S), MOSFET PRODUCT SUMMARY V DS (V) R DS(on) (Ω) (A) a. at V GS = - V - 5-3.8 at V GS = -.5 V - 2 FEATURES TrenchFET Power MOSFETs RoHS COMPLIANT S TO-252 G Drain Connected to
More informationUniversal LED in Ø 5 mm Tinted Diffused Package
TLUR54, TLUR54 Universal LED in Ø 5 mm Tinted Diffused Package 9223 PRODUCT GROUP AND PACKAGE DATA Product group: LED Package: 5 mm Product series: standard Angle of half intensity: ± 3 FEATURES For DC
More informationAluminum Electrolytic Capacitors Power Ultra Miniature Snap-In
Aluminum Electrolytic Capacitors Power Ultra Miniature Snap-In 056/057 PSM-SI miniaturized 156 PUM-SI Fig. 1 high voltage 157 PUM-SI QUICK REFERENCE DATA DESCRIPTION VALUE Nominal case size (Ø D x L in
More informationThrottle Position Sensor in Hall Effect Technology Hollow and D-Shaft Versions
Model 981 HE Throttle Position Sensor in Hall Effect Technology FEATURES Accurate linearity down to: ± 0.5 % Easy mounting principle Non contacting technology: Hall effect Model dedicated to all applications
More informationHigh Speed Infrared Emitting Diode, 850 nm, GaAlAs Double Hetero
High Speed Infrared Emitting Diode, 85 nm, GaAlAs Double Hetero 94 839 DESCRIPTION is an infrared, 85 nm emitting diode in GaAlAs double hetero (DH) technology with high radiant power and high speed, molded
More informationSilicon PIN Photodiode
BPVNF Silicon PIN Photodiode DESCRIPTION 640- BPVNF is a PIN photodiode with high speed and high radiant sensitivity in black, T-¾ plastic package with daylight blocking filter. Filter bandwidth is matched
More informationSingle Phase Rectifier Bridge, 1.2 A
Single Phase Rectifier Bridge, 1.2 A FEATURES VS-1KAB-E Series Ease of assembly, installation, inventory High surge rating Compact Material categorization: For definitions of compliance please see www.vishay.com/doc?99912
More information50 W Power Resistor, Thick Film Technology, TO-220
50 W Power Resistor, Thick Film Technology, TO-220 FEATURES 50 W at 25 C heatsink mounted Adjusted by sand trimming Leaded or surface mount versions High power to size ratio Non inductive element Material
More informationInfrared Emitting Diode, RoHS Compliant, 950 nm, GaAs
DESCRIPTION 94 8638 is an infrared, 95 nm emitting diode in GaAs technology molded in a miniature, clear plastic package without lens. FEATURES Package type: leaded Package form: T-¾ Dimensions (in mm):
More informationFEATURES. Package. PARAMETER SYMBOL PB3506 PB3508 PB3510 UNIT Maximum repetitive peak reverse voltage V RRM V 35 T A = 25 C (2) 4.
PB356, PB358, PB35 Enhanced isocink+ TM Bridge Rectifiers + isocink+ ~ ~ - - ~ ~ + ~ ~ Case Style PB FEATURES UL recognition file number E32394 (QQQX2) UL 557 (see *) Enhanced high-current density single
More informationHigh Power Infrared Emitting Diode, 940 nm, GaAlAs, MQW
High Power Infrared Emitting Diode, 94 nm, GaAlAs, MQW DESCRIPTION 94 8389 is an infrared, 94 nm emitting diode in GaAlAs multi quantum well (MQW) technology with high radiant power molded in a clear,
More informationUF4001, UF4002, UF4003, UF4004, UF4005, UF4006, UF4007 Ultrafast Plastic Rectifier
UF400, UF4002, UF4003, UF4004, UF4005, UF4006, UF4007 Ultrafast Plastic Rectifier FEATURES Glass passivated chip junction Ultrafast reverse recovery time Low forward voltage drop Low switching losses,
More informationHigh Speed Infrared Emitting Diode, 830 nm, GaAlAs Double Hetero
High Speed Infrared Emitting Diode, 83 nm, GaAlAs Double Hetero 26 DESCRIPTION is an infrared, 83 nm emitting diode in GaAlAs double hetero (DH) technology with high radiant power and high speed, molded
More informationFully Sealed Potentiometer Military and Professional Grade
PE0 Fully Sealed Potentiometer Military and Professional Grade DIMENSIONS in millimeters (inches) ± 0.5 mm (± 0.02") FEATURES High power rating W at 70 C Low temperature coefficient (150 ppm/ C typical)
More informationAC Line Rated Ceramic Disc Capacitors Class X1, 400 V AC / Class Y2, 300 V AC / 250 V AC
AC Line Rated Ceramic Disc Capacitors Class X1, V AC / Class Y, V AC / V AC FEATURES Complying with IEC 638-1 3 rd edition High reliability Complete range of capacitance values Radial leads Singlelayer
More informationBidirectional Symmetrical (BiSy) Low Capacitance, Dual-Line ESD-Protection Diode in SOT-323
VCAN26A2-3G Bidirectional Symmetrical (BiSy) Low Capacitance, Dual-Line ESD-Protection Diode in SOT-323 3 1 2 22742 MARKING (example only) 22743 WW VY ABC ABC = type code (see table below) WW = date code
More informationFRED Pt Gen 4 Single Ultrafast Diode, 500 A (INT-A-PAK Power Modules)
FRED Pt Gen 4 Single Ultrafast Diode, 5 A (INT-A-PAK Power Modules) VS-VSKEF5/6PbF INT-A-PAK PRODUCT SUMMARY V R 6 V I F(AV) at T C 5 A at 55 C t rr at 4 ns Type Modules - diode, high voltage Package INT-A-PAK
More informationAluminum Electrolytic Capacitors Radial, High Temperature, Low Impedance, High Vibration Capability
Aluminum Electrolytic Capacitors Radial, High Temperature, Low Impedance, High Vibration Capability 40 RTM lower Z longer life 50 RMI 25 C 46 RTI high vibration QUICK REFERENCE DATA DESCRIPTION VALUE Nominal
More informationFEATURES. IHLP-3232DZ μh ± 20 % ER e3 MODEL INDUCTANCE VALUE INDUCTANCE TOLERANCE PACKAGE CODE JEDEC LEAD (Pb)-FREE STANDARD
IHP-33DZ- IHP Commercial Inductors, High Temperature ( C) Series DESIGN SUPPORT TOOS click logo to get started Models Available STANDARD EECTRICA SPECIFICATIONS INDUCTANCE ± % AT khz,. V, A (μh) Design
More informationFEATURES. Package. PARAMETER SYMBOL PB4006 PB4008 PB4010 UNIT Maximum repetitive peak reverse voltage V RRM V
Enhanced isocink+ TM Bridge Rectifiers + isocink+ ~ ~ - - ~ ~ + ~ ~ Case Style PB FEATURES UL recognition file number E32394 (QQQX2) UL 557 (see *) Enhanced high-current density single in-line package
More informationInfrared Emitting Diode, 950 nm, GaAs
Infrared Emitting Diode, 95 nm, GaAs DESCRIPTION 94 839 TSUS54 is an infrared, 95 nm emitting diode in GaAs technology molded in a blue-gray tinted plastic package. FEATURES Package type: leaded Package
More informationN- and P-Channel 2.5-V (G-S) MOSFET
N- and P-Channel.5-V (G-S) MOSFET PRODUCT SUMMARY V DS (V) (Ω) (A) N-Channel. at = 4.5 V ± 4.5.4 at =.5 V ± 3.9 P-Channel -.5 at = - 4.5 V ± 3.5.85 at = -.5 V ±.7 FEATURES Halogen-free Option Available
More informationSurface Mounted Power Resistor Thick Film Technology
DIMENSIONS in millimeters FEATURES AEC-Q200 qualified 35 W at 25 C case temperature Surface mounted resistor - TO-263 (D 2 PAK) style package Wide resistance range from 0.01 to 550 k Non inductive Resistor
More informationIR Sensor Module for Remote Control Systems
IR Sensor Module for Remote Control Systems DESIGN SUPPORT TOOLS Models Available MECHANICAL DATA Pinning: 1 = carrier OUT, 2 = GND, 3 = V S 19026 click logo to get started FEATURES Photo detector and
More informationAluminum Electrolytic Capacitors Axial High Temperature, High Ripple Current
Aluminum Electrolytic Capacitors Axial High Temperature, High Ripple Current smaller 9 AHT-DIN 8 AHT lower dimensions higher ripple Fig. 25 C 38 AML QUICK REFERENCE DATA DESCRIPTION VALUE Nominal case
More informationZener Diodes FEATURES
ZMYV9 to ZMY Zener Diodes PRIMARY CHARACTERISTICS PARAMETER VALUE UNIT range nom..9 to V FEATURES Silicon planar power Zener diodes For use in stablilizing and clipping circuits with high power rating
More informationLower Voltage Ceramic Singlelayer DC Disc Capacitors 1 kv DC to 3 kv DC Low Dissipation Factor
Lower Voltage Ceramic Singlelayer DC Disc Capacitors 1 kv DC to 3 kv DC Low Dissipation Factor FEATURES Low losses High stability Low DF minimizes self heating at HF Ideal for high switching to khz Radial
More informationHEXFRED Ultrafast Diodes, 100 A (INT-A-PAK Power Modules)
HEXFRED Ultrafast Diodes, A (INT-A-PAK Power Modules) INT-A-PAK PRIMARY CHARACTERISTICS V R 1200 V V F (typical) 2.5 V t rr (typical) 150 ns I F(DC) at T C 110 A at C Package INT-A-PAK Circuit configuration
More informationN-Channel 60-V (D-S) MOSFET
Si8DS N-Channel -V (D-S) MOSFET PRODUCT SUMMARY V DS (V) R DS(on) (Ω) I D (A). at V GS = V.. at V GS = 4.5 V.7 FEATURES Halogen-free According to IEC 4-- Available TrenchFET Power MOSFET % R g Tested TO-
More informationIR Sensor Module for Remote Control Systems
IR Sensor Module for Remote Control Systems 1 2 DESIGN SUPPORT TOOLS Models Available MECHANICAL DATA 3 Pinning: 1 = GND, 2 = Carrier OUT, 3 = V S 94 8691 click logo to get started FEATURES Photo detector
More informationHigh Speed Infrared Emitting Diode, 830 nm, GaAlAs Double Hetero
High Speed Infrared Emitting Diode, 83 nm, GaAlAs Double Hetero 94 8389 DESCRIPTION is an infrared, 83 nm emitting diode in GaAlAs double hetero (DH) technology with high radiant power and high speed,
More informationStandard Recovery Diodes (Stud Version), 12 A
Standard Recovery Diodes (Stud Version), 12 A VS- FEATURES High surge current capability Stud cathode and stud anode version Wide current range DO-203AA (DO-4) Types up to 1200 V V RRM Designed and qualified
More informationSingle Phase Bridge Rectifier, 2 A
Single Phase Bridge Rectifier, 2 FETURES Suitable for printed circuit board mounting Compact construction High surge current capability Material categorization: for definitions of compliance please see
More informationSingle phase bridge. (Power Modules), 25 A / 35 A
Single Phase Bridge (Power Modules), 25 A / 35 A D-34 PRIMARY CHARACTERISTICS I O 25 A to 35 A V RRM 200 V to 1200 V Package D-34 Circuit configuration Single phase bridge FEATURES Universal, 3 way terminals:
More informationBidirectional Symmetrical (BiSy) Low Capacitance, Dual-Line ESD Protection Diode in SOT-23
VCAN26A2-3S Bidirectional Symmetrical (BiSy) Low Capacitance, Dual-Line ESD Protection Diode in SOT-23 FEATURES 3 For CAN and FLEX-Bus applications Small SOT-23 package AEC-Q1 qualified available 1 2 22742
More informationInfrared Emitting Diode, RoHS Compliant, 950 nm, GaAs
Infrared Emitting Diode, RoHS Compliant, DESCRIPTION 948642 is an infrared, 95 nm emitting diode in GaAs technology in a hermetically sealed TO-18 package with lens. FEATURES Package type: leaded Package
More informationPower Resistor, for Mounting onto a Heatsink Thick Film Technology
Power Resistor, for Mounting onto a Heatsink Thick Film Technology FEATURES 5 W to 50 W High power rating Manufactured in cermet thick film technology, these power resistors exhibit remarkable characteristics
More informationSilicon NPN Phototransistor, RoHS Compliant
Silicon NPN Phototransistor, RoHS Compliant TEST26 DESCRIPTION 9 673 TEST26 is a silicon NPN phototransistor with high radiant sensitivity in black, miniature, side view plastic package with daylight blocking
More informationHigh Speed Infrared Emitting Diode, 890 nm, GaAlAs Double Hetero
High Speed Infrared Emitting Diode, 89 nm, GaAlAs Double Hetero 94 8389 DESCRIPTION is an infrared, 89 nm emitting diode in GaAlAs double hetero (DH) technology with high radiant power and high speed,
More informationLead (Pb)-Bearing Thick Film, Rectangular Chip Resistors
Lead (Pb)-Bearing Thick Film, Rectangular Chip Resistors FEATURES High pulse performance (time/power) Metal glaze on high quality ceramic Protective overglaze Lead (Pb)-bearing solder contacts on Ni barrier
More informationInsulated Precision Wirewound Resistors Axial Leads
Insulated Precision Wirewound Resistors Axial Leads In wirewound precision resistors, the series holds a leading position in professional applications whenever an excellent stability of the ohmic value
More informationWirewound Resistors, Military, MIL-PRF Qualified, Type RE, Aluminum Housed, Chassis Mount
Wirewound Resistors, Military, MIL-PRF-18546 Qualified, Type RE, Aluminum Housed, Chassis Mount STANDARD ELECTRICAL SPECIFICATIONS MILITARY VISHAY REFERENCE POWER RATING P 25 C W FEATURES Molded construction
More informationSingle phase bridge. (Power Modules), 25 A, 35 A
Single Phase Bridge (Power Modules), 25 A, 35 A GBPC...A GBPC...W PRIMARY CHARACTERISTICS I O 25 A, 35 A V RRM V to V Package GBPC..A, GBPC..W Circuit configuration Single phase bridge FEATURES Universal,
More informationN-Channel 2.5-V (G-S) Battery Switch, ESD Protection
N-Channel.-V (G-S) Battery Switch, ESD Protection Si694AEDQ PRODUCT SUMMARY V DS (V) R DS(on) (Ω) I D (A).33 at V GS = 4. V 4.6 8.38 at V GS = 3. V 4.3.4 at V GS =. V 4. FEATURES Halogen-free Low R DS(on)
More informationSingle phase bridge. (Power Modules), 25 A/35 A
Single Phase Bridge (Power Modules), 25 A/35 A D-34 PRIMARY CHARACTERISTICS I O 25 A to 35 A V RRM 1 V to 1600 V Package D-34 Circuit configuration Single phase bridge FEATURES Universal, 3 way terminals:
More informationTen Turns Servo or Bushing Mount Hall Effect Sensor in Size 09 (22.2 mm)
Ten Turns Servo or Bushing Mount Hall Effect Sensor in Size 09 (22.2 mm) ELECTRICAL SPECIFICATIONS FEATURES All electrical angles available up to: 3600 Accurate linearity down to: ± 0.5 % Very long life:
More informationN- and P-Channel 30-V (D-S) MOSFET
N- and P-Channel -V (D-S) MOSFET PRODUCT SUMMARY V DS (V) (Ω) I D (A) N-Channel.3 at V GS = V 5.9.53 at V GS = 4.5 V 4.9 P-Channel -.53 at V GS = - V - 4.9.9 at V GS = - 4.5 V - 3.7 FEATURES Halogen-free
More informationThree phase bridge. (Power Module), 200 A
Three Phase Bridge (Power Module), 2 A VS-2MT4KPbF MTK PRIMARY CHARACTERISTICS I O 2 A V RRM 4 V Package MTK Circuit configuration Three phase bridge FEATURES Package fully compatible with the industry
More informationDual N-Channel 30-V (D-S) MOSFET
Dual N-Channel 3-V (D-S) MOSFET PRODUCT SUMMARY V DS (V) (Ω) I D (A).95 at V GS = V. 3. at V GS = 4.5 V 9.4 FEATURES Halogen-free Option Available TrenchFET Power MOSFET % R g Tested APPLICATIONS DC/DC
More informationStandard Diodes (Super MAGN-A-PAK Power Modules), 600 A
Standard Diodes (Super MAGN-A-PAK Power Modules), 6 A FEATURES High current capability High surge capability High voltage ratings up to 2 V 3 V RMS isolating voltage with non-toxic substrate Industrial
More informationRotational Absolute Magnetic Kit Encoder Version 33 LP and HP Displacement Sensor
Rotational Absolute Magnetic Kit Encoder Version 33 LP and HP Displacement Sensor DESIGN SUPPORT TOOLS Models Available click logo to get started QUICK REFERENCE DATA Sensor type ROTATIONAL, magnetic technology
More informationSmall Signal Zener Diodes
Small Signal Zener Diodes PRIMARY CHARACTERISTICS PARAMETER VALUE UNIT V Z range nom. 2.4 to 75 V Test current I ZT.7 to 2 ma V Z specification Thermal equilibrium Int. construction Single FEATURES Silicon
More information3-Channel EMI-Filter with ESD-Protection
3-Channel EMI-Filter with ESD-Protection 6 5 4 7 2 3 9423 MARKING (example only) 257 XX YY Dot = pin marking YY = type code (see table below) XX = date code 2 FEATURES Ultra compact LLP75-7L package 3-channel
More information