ULP (Ultra-Low-Power) Wifi accelerometer with built-in data logger

Transcription

1 ULP (Ultra-Low-Power) Wifi accelerometer with built-in data logger

2 AX-3D APPLICATIONS VIDE O Technical Note USER MANUAL Mechanical Drawing DRAWING OVERVIEW ULP (Ultra Low Power) Wifi technology Waterproof IP67 Embedded data logger: up to 5 million data points (with events dating) USB 2.0: device configuration and 5V power supply High accuracy Accelerometer (measurement range ±2g or ±10g) FFT and DIN (Ground Vibration) modules available SSD (Smart Shock Detection) Store & Forward+ : lossless data transmission with hard real-time Excellent radio link relying on the radio antenna diversity developed by Beanair

3 AX-3D APPLICATIONS Dynamic measurement on rolling stock Condition Monitoring Structural Health Monitoring Vibration Analysis on construction site AX-3D

4 AX-3D AN OPEN-STANDARD & INDUSTRIAL WIFI TECHNOLOGY ULP (Ultra Low power) Wifi IEEE b/g/n Lower total cost of ownership-works with existing access points Large installed base and consequent broad-based familiarity with configuration, use and troubleshooting at the physical and link layers Easy provisioning & IT friendly: our ULP wifi sensors use IP-over-Ethernet networking environment A RELIABLE WIFI TECHNOLOGY THANKS TO OUR STORE AND FORWARD+ FUNCTION The store and forward technique works by storing the message transmitted by the BeanDevice Wilo (wireless DAQ/sensor) to a Wifi access point/ Wifi receiver. If the message is not received due to a network disruption, it will be retransmitted on the next transmission cycle. This technique allows to bring a lossless data transmission. User can also enable the Hard real-time option; i.e. the message must be received by the Wifi Access Point/Wifi Receiver within the confines of a stringent deadline. It is automatically deleted if it failed to reach its destination within the allotted time span

5 AX-3D TECHNICAL SPECIFICATIONS Product reference BND-WILO-AX-3D -MR-MO MR Measurement Range: 2: ±2g measurement range 10: ±10g measurement range MO - Mounting option BR - 90 Mounting bracket M - Magnet Mounting Example 1: BND-WILO-AX3D-10G-BR Wireless Accelerometer with ±10g range with 90 Mounting bracket Example 2: BND-WILO-AX3D-2G-M Wireless Accelerometer with ±2g range with magnet mounting Accelerometer technology Accelerometer measurement range Sensitivity Typical non-linearity Analog to Digital converter Sensor frequency response (-3 db) Maximum sampling rate Noise spectral density Zero-g Offset Variation from RT over Temp High precision accelerometer based on MEMS technology ±2g and ±10g ±2g Version : 0.24 µg/digit ±10g version: 0.59 µg/digit ±0.1% FS 24-bit delta-sigma with temperature compensation Synhcronuous measurement channel DC to 800 Hz 3 ksps per axis ±2g Version : 45 µg/ Hz ±10g version: 100 µg/ Hz ±2g Version : ±0.2 mg/ C

6 AX-3D TECHNICAL SPECIFICATIONS Sensitivity Variation from RT over Temp Offset Ratiometric Error Sensitivity Ratiometric Error Cross Axis Sensitivity ±2g Version : ±0.01 %/ C (XY), ±0.02 %/ C (Z) ±10g version: ±0.01 %/ C ±2g Version : 4mg ±10g version: ±0.2% (XY), ±0.1% (Z) ±2g Version : ±1.25 % (X-Y), ±0.2 % (Z) ±10g Version : ±1.6% (X-Y), ±0.2 % (Z) 0,02 Shock Sensor technology Shock sensor range MEMS technology ±2g/±4g/±6g/±8g/±16g dynamically selectable from the BeanScape software ±2g range: 0.06 mg/digit ±4g range: 0.12 mg/digit Sensitivity ±6g range: 0.06 mg/digit ±8g range: 0.12 mg/digit ±16g range: 0.12 mg/digit Typical non-linearity Analog to Digital converter Sensor frequency response (-3 db) Maximum sampling rate Noise spectral density ±0.15% on the FS 12-bits with temperature compensation DC to 800 Hz 1.6 ksps per axis 150 µg/ Hz

7 AX-3D TECHNICAL SPECIFICATIONS Sensitivity change Vs temperature ±0,01% / C Zero-g level change vs temperature (max delta from 25 C) Typical zero-g level offset accuracy ±0.5 mg/ C ±40 mg Low Duty Cycle Data Acquisition (LDCDA) Mode: 1s to 24 hour Data Acquisition mode (SPS = sample per second) Alarm -Low duty cycle: 1s to 24 hour Streaming mode : 100 SPS by default Alarm Streaming Mode : 100 SPS by default Sampling Rate (in streaming mode) Alarm Threshold Power Mode Minimum: 1 SPS Maximum: 3 ksps per axis 2 high levels alarms & 2 low levels alarms Sleeping with Network Listening & Active Wireless Protocol Stack WSN Topology Crypto Engine Data rate IEEE b/g/n Point-to-Point / Star / Cluster-Tree WPA2, WPS2, EAP-TTLS 16 Mbps

8 AX-3D TECHNICAL SPECIFICATIONS RF Characteristics TX Power Rx Sensitivity Maximum Radio Range ISM 2.4GHz 16 Channels. Antenna diversity architecture designed by Beanair 18 1 DSSS OFDM DSSS OFDM 200 m (L.O.S.), radio range can be extended by adding wifi repeater Antenna Antenna diversity : 2 omnidirectional antenna with a gain of 2,8 dbi USB standard Data Rate Related functions USB 2.0 Full speed operation(12mb/s) Firmware update Measurement logs donwload Embedded Data logger Storage capacity Wireless data downloading up to 5 million data points 3 minutes to download the full memory (average time)

9 AX-3D TECHNICAL SPECIFICATIONS TimeSync function : Clock synchronization over the Wireless Sensor Networks (WSN) Clock synchronization accuracy ±2.5 ms (at 25 C) Tolerance ±10ppm, stability ±10ppm Environmental and Mechanical Casing Aluminum casing Dimensions in mm (LxWxH):35x59x65 mm without antenna & eyelet, Weight (battery included) : 115g IP NEMA Rating Shock resistance Operating Temperature Ip67 Nema 6 100g during 50 ms -40 C to +65 C CE Labelling Directive R&TTE (Radio) ETSI EN (Europe) FCC (North America) ARIB STD-T66 Ver. 3.6 (Japan) ROHS - Directive 2002/95/EC Power supply Rechargeable battery Integrated battery charger High density Lithium-Ion rechargeable battery with a capacity of 780 mah Integrated Lithium-ion battery charger with high precision battery monitoring

10 AX-3D TECHNICAL SPECIFICATIONS Power supply During data acquisition : 20 to 30 ma During Radio transmission : Current 3,3V - 1 DSSS ma - 54 OFDM ma During sleeping : < 30 µa External power supply Two power supplies available: - USB Power supply 5V - 4.8VDC to 17.8 VDC Option(s) Power-supply M8 Cable Wall plug-in, Switchmode power Supply 1,25A with USB plug M8-5Pins Cable, cable length : 2 meters standards (DRAKKS)

11 AX-3D BeanDevice Front View Radome Antenna M8-5 pins connector for USB & Power supply Activity / Failure LED Battery LED CONTACT US Telefon: +49 (0) Fax: +49 (0) beanair@additive-net.de Visit our Websites

12 AX-3DS ULP ( Ultra-Low-Power) Wifi Accelerometer with built-in datalogger

13 Shock Sensor AX-3DS APPLICATIONS VIDE O Technical Note USER MANUAL Mechanical Drawing DRAWING MAIN FEATURES ULP (Ultra Low Power) Wifi technology Waterproof IP67 Embedded data logger: up to 5 million data points (with events dating) USB 2.0: device configuration and 5V power supply Scalable shock measurement range : ±2/4/8/16g Store & Forward+ : lossless data transmission with hard real-time SSD (Smart Shock Detection) Excellent radio link relying on the radio antenna diversity developed by Beanair

14 Shock Sensor AX-3DS APPLICATIONS Structural Health Monitoring Shock measurement on vehicles & trains Transportation Monitoring Drop testing Crash and impact testing Ride quality measurement AX-3DS

15 Shock Sensor AX-3DS AN OPEN-STANDARD & INDUSTRIAL WIFI TECHNOLOGY ULP (Ultra Low power) Wifi IEEE b/g/n Lower total cost of ownership-works with existing access points Large installed base and consequent broad-based familiarity with configuration, use and troubleshooting at the physical and link layers Easy provisioning & IT friendly: our ULP wifi sensors use IP-over-Ethernet networking environment A RELIABLE WIFI TECHNOLOGY THANKS TO OUR STORE AND FORWARD+ FUNCTION The store and forward technique works by storing the message transmitted by the BeanDevice Wilo (wireless DAQ/sensor) to a Wifi access point/ Wifi receiver. If the message is not received due to a network disruption, it will be retransmitted on the next transmission cycle. This technique allows to bring a lossless data transmission. User can also enable the Hard real-time option; i.e. the message must be received by the Wifi Access Point/Wifi Receiver within the confines of a stringent deadline. It is automatically deleted if it failed to reach its destination within the allotted time span

16 Shock Sensor AX-3DS SPECIFICATIONS Product reference BND-WILO-AX-3DS --MR MO MR Measurement Range: 16: ±2/4/8/16g measurement range MO - Mounting option BR - 90 Mounting bracket M - Magnet Mounting Example 1: BND-WILO-AX3DS-16G-BR Wireless Shock sensor with ±16g of range with 90 Mounting bracket Example 2: BND-WILO-AX3D-16G-M Wireless Shock sensor with ±16g of range with magnet mounting Shock Sensor technology Shock sensor range Sensitivity Typical non-linearity Analog to Digital converter Sensor frequency response (-3 db) Maximum sampling rate Noise spectral density Sensitivity change Vs temperature Zero-g level change vs temperature (max delta from 25 C) MEMS technology ±2g/±4g/±6g/±8g/±16g dynamically selectable from the BeanScape software ±2g range: 0.06 mg/digit ±4g range: 0.12 mg/digit ±6g range: 0.06 mg/digit ±8g range: 0.12 mg/digit ±16g range: 0.12 mg/digit ±0.15% on the FS 12-bits with temperature compensation DC to 800 Hz 1.6 ksps per axis 150 µg/ Hz ±0,01% / C ±0.5 mg/ C

17 Shock Sensor AX-3DS SPECIFICATIONS Typical zero-g level offset accuracy ±40 mg Low Duty Cycle Data Acquisition (LDCDA) Mode: 1s to 24 hour Data Acquisition mode (SPS = sample per second) Alarm -Low duty cycle: 1s to 24 hour Streaming mode : 100 SPS by default Alarm Streaming Mode : 100 SPS by default Sampling Rate (in streaming mode) Alarm Threshold Power Mode Minimum: 1 SPS Maximum: 3 ksps per axis 2 high levels alarms & 2 low levels alarms Sleeping with Network Listening & Active Wireless Protocol Stack WSN Topology Crypto Engine Data rate RF Characteristics TX Power IEEE b/g/n Point-to-Point / Star / Cluster-Tree WPA2, WPS2, EAP-TTLS 16 Mbps ISM 2.4GHz 16 Channels. Antenna diversity architecture designed by Beanair 18 1 DSSS OFDM

18 Shock Sensor AX-3DS SPECIFICATIONS Rx Sensitivity Maximum Radio Range DSSS OFDM 200 m (L.O.S.), radio range can be extended by adding wifi repeater Antenna Antenna diversity : 2 omnidirectional antenna with a gain of 2,8 dbi USB standard Data Rate Related functions USB 2.0 Full speed operation(12mb/s) Firmware update Measurement logs donwload Embedded Data logger Storage capacity Wireless data downloading up to 5 million data points 3 minutes to download the full memory (average time) TimeSync function : Clock synchronization over the Wireless Sensor Networks (WSN) Clock synchronization accuracy ±2.5 ms (at 25 C) Tolerance ±10ppm, stability ±10ppm

19 Shock Sensor AX-3DS SPECIFICATIONS Environmental and Mechanical Casing Aluminum casing Dimensions in mm (LxWxH):35x59x65 mm without antenna & eyelet, Weight (battery included) : 115g IP NEMA Rating Shock resistance Operating Temperature Ip67 Nema 6 100g during 50 ms -40 C to +65 C CE Labelling Directive R&TTE (Radio) ETSI EN (Europe) FCC (North America) ARIB STD-T66 Ver. 3.6 (Japan) ROHS - Directive 2002/95/EC Power supply Rechargeable battery Integrated battery charger High density Lithium-Ion rechargeable battery with a capacity of 780 mah Integrated Lithium-ion battery charger with high precision battery monitoring During data acquisition : 20 to 30 ma During Radio transmission : Current 3,3V - 1 DSSS ma - 54 OFDM ma During sleeping : < 30 µa

20 Shock Sensor AX-3DS SPECIFICATIONS Power supply External power supply Two power supplies available: - USB Power supply 5V - 4.8VDC to 17.8 VDC Option(s) Power-supply M8 Cable Wall plug-in, Switchmode power Supply 1,25A with USB plug M8-5Pins Cable, cable length : 2 meters standards (DRAKKS)

21 Shock Sensor AX-3DS BeanDevice Front View Radome Antenna M8-5 pins connector for USB & Power supply Activity / Failure LED Battery LED CONTACT US Telefon: +49 (0) Fax: +49 (0) beanair@additive-net.de Visit our Websites

22 Hi-Inc ULP ( Ultra-Low-Power) Wifi Inclinometer with built-in datalogger

23 H-i-Inc APPLICATIONS VIDE O Technical Note USER MANUAL Mechanical Drawing DRAWING OVERVIEW ULP (Ultra Low Power) Wifi technology Waterproof IP67 Embedded data logger: up to 5 million data points (with events dating) USB 2.0: device configuration and 5V power supply High accuracy bi-axis inclinometer ±15 or ±30 Store & Forward+ : lossless data transmission with hard real-time SSD (Smart Shock Detection) Excellent radio link relying on the radio antenna diversity developed by Beanair

24 H-i-Inc APPLICATIONS Structural Health Monitoring Shock measurement on vehicles & trains Transportation Monitoring Drop testing Crash and impact testing Ride quality measurement Hi-Inc

25 H-i-Inc AN OPEN-STANDARD & INDUSTRIAL WIFI TECHNOLOGY ULP (Ultra Low power) Wifi IEEE b/g/n Lower total cost of ownership-works with existing access points Large installed base and consequent broad-based familiarity with configuration, use and troubleshooting at the physical and link layers Easy provisioning & IT friendly: our ULP wifi sensors use IP-over-Ethernet networking environment A RELIABLE WIFI TECHNOLOGY THANKS TO OUR STORE AND FORWARD+ FUNCTION The store and forward technique works by storing the message transmitted by the BeanDevice Wilo (wireless DAQ/sensor) to a Wifi access point/ Wifi receiver. If the message is not received due to a network disruption, it will be retransmitted on the next transmission cycle. This technique allows to bring a lossless data transmission. User can also enable the Hard real-time option; i.e. the message must be received by the Wifi Access Point/Wifi Receiver within the confines of a stringent deadline. It is automatically deleted if it failed to reach its destination within the allotted time span

26 H-i-Inc TECHNICAL SPECIFICATIONS Product reference BND-WILO-HI-INC-MR MR Measurement Range: 15B : bi-axis ±15 30B : bi-axis ±30 MO - Mounting option BR - 90 Mounting bracket M - Magnet Mounting Example 1: BND-WILO-HI-INC-15B-BR -wireless bi-axis inclinometer with ±15 measurement range with 90 bracket mounting Example 2: BND-WILO-HI-INC-30B-M -wireless bi-axis inclinometer with ±30 measurement range with magnet mounting Inclinometer Technology Measurement resolution (Bandwidth 10 Hz) Noise density Accuracy (Full scale) Offset temperature dependency (temperature range 25 C to +85 C) Sensitivity temperature dependency (temperature range 25 C to +85 C) Long term stability (@23 C) Analog to Digital converter Sensor frequency Response (-3dB) Noise spectral density DC to 100 Hz Inclinometer based on MEMS Technology / Hz ±0.05 ±0.002 / C ±0.005 %/ C with temperature compensation ±0.013 %/ C without temperature compensation < bit delta-sigma with temperature compensation Synhcronuous measurement channel DC to 28 Hz / Hz

27 H-i-Inc TECHNICAL SPECIFICATIONS Shock Sensor technology Shock sensor range MEMS technology ±2g/±4g/±6g/±8g/±16g dynamically selectable from the BeanScape software ±2g range: 0.06 mg/digit ±4g range: 0.12 mg/digit Sensitivity ±6g range: 0.06 mg/digit ±8g range: 0.12 mg/digit ±16g range: 0.12 mg/digit Typical non-linearity Analog to Digital converter Sensor frequency response (-3 db) Maximum sampling rate ±0.15% on the FS 12-bits with temperature compensation DC to 800 Hz 1.6 ksps per axis Noise spectral density 150 µg/ Hz Sensitivity change Vs temperature ±0,01% / C Zero-g level change vs temperature (max delta from 25 C) Typical zero-g level offset accuracy ±0.5 mg/ C ±40 mg

28 H-i-Inc TECHNICAL SPECIFICATIONS Low Duty Cycle Data Acquisition (LDCDA) Mode: 1s to 24 hour Data Acquisition mode (SPS = sample per second) Alarm -Low duty cycle: 1s to 24 hour Streaming mode : 100 SPS by default Alarm Streaming Mode : 100 SPS by default Sampling Rate (in streaming mode) Alarm Threshold Power Mode Minimum: 1 SPS Maximum: 3 ksps per axis 2 high levels alarms & 2 low levels alarms Sleeping with Network Listening & Active Wireless Protocol Stack WSN Topology Data rate RF Characteristics Receiver Sensitivity Maximum Radio Range IEEE b/g/n Point-to-Point / Star / Cluster-Tree 16 Mbps ISM 2.4GHz 16 Channels. Antenna diversity architecture designed by Beanair DSSS OFDM 200 m (L.O.S.), radio range can be extended by adding wifi repeater Antenna Antenna diversity : 2 omnidirectional antenna with a gain of 2,8 dbi

29 H-i-Inc TECHNICAL SPECIFICATIONS Embedded Data logger Storage capacity Wireless data downloading up to 5 million data points 3 minutes to download the full memory (average time) TimeSync function : Clock synchronization over the Wireless Sensor Networks (WSN) Clock synchronization accuracy ±2.5 ms (at 25 C) Tolerance ±10ppm, stability ±10ppm Environmental and Mechanical Casing Aluminum casing Dimensions in mm (LxWxH):35x59x65 mm without antenna & eyelet, Weight (battery included) : 115g IP NEMA Rating Shock resistance Operating Temperature Ip67 Nema 6 100g during 50 ms -40 C to +65 C CE Labelling Directive R&TTE (Radio) ETSI EN (Europe) FCC (North America) ARIB STD-T66 Ver. 3.6 (Japan) ROHS - Directive 2002/95/EC

30 H-i-Inc TECHNICAL SPECIFICATIONS Power supply Rechargeable battery Integrated battery charger High density Lithium-Ion rechargeable battery with a capacity of 780 mah Integrated Lithium-ion battery charger with high precision battery monitoring During data acquisition : 20 to 30 ma During Radio transmission : Current 3,3V - 1 DSSS ma - 54 OFDM ma During Power sleeping supply : < 30 µa External power supply Two power supplies available: - USB Power supply 5V - 4.8VDC to 17.8 VDC Option(s) Power-supply Wall plug-in, Switchmode power Supply 1,25A with USB plug Calibration certificate linked to national and internatiional standards (DRAKKS)

31 H-i-Inc BeanDevice Front View Radome Antenna M8-5 pins connector for USB & Power supply Activity / Failure LED Battery LED CONTACT US Telefon: +49 (0) Fax: +49 (0) beanair@additive-net.de Visit our Websites