INSPECTION. If resistance value is not as specified, replace the cooler thermistor. Resistance (kω) Temperature ( C)
|
|
- Jennifer Wiggins
- 5 years ago
- Views:
Transcription
1 INSPECTION Y01 1. COOLER THERMISTOR NO.1 (a) Inspect cooler thermistor No.1 continuity. (1) Measure the resistance between terminals 1 and 2 of the cooler thermistor No. 1 at each temperature, as shown in the chart. E Resistance (kω) Temperature ( C) I30145 If resistance value is not as specified, replace the cooler thermistor No
2 THERMISTOR ASSY (a) Inspect thermistor assy continuity. (1) Measure the resistance between terminals 1 and 2 of thermistor assy according to the value(s) in the table below. Condition Specified condition Approx.: 30 C (86 F) 80 to 100 kω I37368 Approx.: 25 C (77 F) 4.8 to 5.2 kω Approx.: 40 C (104 F) to kω Approx.: 100 C (212 F) 0.3 to 0.37 kω If the value is not as specified, replace the thermistor assy. 3. CENTER CLUSTER MODULE SWITCH (a) Inspect blower switch continuity. Condition / Circuit Tester connection Specified condition OFF kω or higher LO 1 2 Below 1 Ω OFF LO M1 M2 LO M Below 1 Ω M Below 1 Ω M1 M Below 1 Ω HI M Below 1 Ω M2 HI Below 1 Ω HI Below 1 Ω I37371 If the value is not as specified, replace the center cluster module switch. (b) Inspect illumination operation. Connect the positive (+) lead from the battery to terminal 4 and negative () lead to terminal 5, then check that the illuminations come on. If there is any bulb which does not come on, replace the bulb. 1478
3 5513 (c) Inspect switch continuity. Measure the resistance according to the value(s) in the table below. Switch operation Tester connection Specified condition ON 3 1 and 2 Below 1 Ω OFF 3 1 and 2 10 kω or higher If continuity is not as specified, replace the cooler switch. (d) Inspect indicator operation. (1) Connect the positive (+) lead from the battery to terminal 3 and the negative () lead to terminal 1. (2) Push the A/C button in and then check that the indicator comes on. If operation is not as specified, replace the cooler switch. E62517 E BLOWER RESISTOR (a) Inspect blower resistor continuity. Tester connection Specified condition to Ω to Ω to Ω If the value is not as specified, replace the blower resistor BLOWER W/FAN MOTOR SUBASSY (a) Inspect blower w/fan motor subassy. (1) Connect the positive (+) lead from the battery to terminal 2 and negative () lead to terminal 1, then check that the motor operates smoothly. If operation is not as specified, replace the blower motor. I
4 5514 FRESH/RECIRC FRESH RECIRC 6. DAMPER SERVO SUBASSY (a) Inspect damper servo subassy. (1) Connect the positive (+) lead from the battery to terminal 7 and the negative () lead to terminal 8. Measuring condition Battery negative () Terminal 1 Battery negative () Terminal 2 Battery negative () Terminal 3 Operation RECIRC RECIRC/FRESH FRESH If operation is not as specified, replace the damper servo sub assy. E32889 E32994 I W/PULLEY COMPRESSOR ASSY (a) Inspect w/pulley compressor assy. (1) Measure the resistance between terminals 1 and 2. Standard resistance: 160 to 320 Ω at 20 C (68 F) If the value is not as specified, replace the w/pulley compressor assy. E60999 E61224 E62758 I COOLER WIRING NO.2 (a) Inspect foot, foot/def switch continuity. Switch operation Tester connection Specified condition ON 1 3 Below 1 Ω OFF kω or higher Connector A Connector B (b) Inspect MAX hot switch continuity. (1) Using a service wire, connect connector A1 and connector A2 between the MAX hot switch and cooler wiring No.2. (2) Check that the continuity exists between terminals. Measuring condition Operation Connector B2 Connector B3 Below 1 Ω E62758 I
5 5515 E HEATER SWITCH ASSY (a) Inspect heater switch assy continuity. Condition Tester connection Specified condition Air inlet damper control lever FRS kω or higher Air inlet damper control lever REC Air mix switch MAX HOT Air mix switch Except MAX HOT 1 2 Below 1 Ω 3 4 Below 1 Ω kω or higher If continuity is not as specified, replace the heater switch assy. E62758 I MAX HOT SWITCH (a) Inspect MAX hot switch continuity. Switch operation Tester connection Specified condition ON 1 2 Below 1 Ω OFF kω or higher If continuity is not as specified, replace the max hot switch. E HEATER BLOWER MOTOR RELAY ASSY (a) Inspect relay assy (for heater blower motor) continuity. Condition Tester connection Specified condition Constant Below 1 Ω Apply B+ between terminal 1 and Below 1 Ω If the value is not as specified, replace the relay assy (for heater blower motor). 1481
6 5516 E PTC HEATER RELAY (a) Inspect PTC heater relay continuity. Condition Tester connection Specified condition Constant kω or higher Apply B+ between terminal 1 and Below 1 Ω If the value is not as specified, replace the PTC heater relay. 1482
2005 Toyota RAV ACCESSORIES & EQUIPMENT Defogger System - RAV4 LOCATION
2005 ACCESSORIES & EQUIPMENT Defogger System - RAV4 LOCATION Fig. 1: Identifying Defogger System Component Locations INSPECTION 1. CHECK DEFOGGER SWITCH CIRCUIT Disconnect the connector from the heater
More informationElectronics Merit Badge Class 4. 12/30/2010 Electronics Merit Badge Class 4 1
Electronics Merit Badge Class 4 12/30/2010 Electronics Merit Badge Class 4 1 Soldering Safety Note: A Soldering Iron gets hotter than 374 F. Do not touch the soldering iron s metal parts or you will receive
More informationELEC1 (JUN13ELEC101) General Certificate of Education Advanced Subsidiary Examination June Introductory Electronics TOTAL. Time allowed 1 hour
Centre Number Surname Candidate Number For Examiner s Use Other Names Candidate Signature Examiner s Initials Question Mark General Certificate of Education Advanced Subsidiary Examination June 2013 1
More informationPROBLEM SYMPTOMS TABLE
18 Radio receiver assembly PROBLEM SYMPTOMS TABLE HINT: Inspect the fuse and relay before confirming the suspected area as shown in the table below. Symptom Suspected area See page Pressing power switch
More informationELECTRIC CIRCUITS AND ELECTRONICS
Circuitos eléctricos y electrónicos ELECTRIC CIRCUITS AND ELECTRONICS Technology, programming and robotics II Electric Circuitos circuits eléctricos and y electronics electrónicos AN ELECTRICAL CIRCUIT
More informationWIRING DIAGRAMS FOR SMART MODELS
SMART SERIES CODING SYSTEM FOR AV ACTUATOR WIRING DIAGRAMS There are 3 elements to the wiring codes used in AVA electric actuators: CONTROL WIRING CODE CONTROL WIRING TYPE 1 3 Wire system, single pole
More informationElectricity Transition Questions Applied General in Science
Electricity Transition Questions Applied General in Science Marks: 62 marks Pass = 30% Comments: Merit = 45% Distinction = 65% Name: Teacher: MDS Date: Q1. (a) Draw one line from each circuit symbol to
More informationTheme 5: Electricity in the Home
Theme 5: Electricity in the Home!!" # # $%& $'&( ) * +,, ( * $ & $ & #.! $ & /+ $ & / " /+ 0 ' / / / / # 1 /$ %% # & ' # $ 2 $& $ 3 2 & #( ' ) & & * '% & '' + + $ % *'% & # + $ + $%' # *,, $%& $'& $, 4
More informationCAUTION All safety information must be followed as provided in Service Manual
Domestic Microwave Technical Information AMV6167BD* JMV8166BA* JMV9169BA* Due to possibility of personal injury or property damage, always contact an authorized technician for servicing or repair of this
More informationElectromagnetism Unit- Current Sub-Unit
4.2.1 Electrical Current Definitions current unit: or requires: Example #3 A wire carries a current of 50 amperes. How much charge flows through the wire in 10 seconds? How many electrons pass through
More informationAuto Diagnosis Test #2 Review
Auto Diagnosis Test #2 Review Your own hand written notes may be used for the 1 st 10 minutes of the test For the Most Effective Personal Review, Look Over the On Line Study Guide Multimedia Based on Chapters
More information3/4/2015. Basic relay construction. Shading coil in AC relays. Timothy L. Skvarenina and William E. DeWitt Electrical Power and Controls, 2e
FIGURE 12-1 Basic relay construction. FIGURE 12-2 Shading coil in AC relays. 1 FIGURE 12-3 Contactor coil and shaded pole stators. FIGURE 12-4 Magnetic motor starter. 2 FIGURE 12-5 Thermal overload devices.
More informationA.M. WEDNESDAY, 19 May minutes
Candidate Name Centre Number Candidate Number 0 GCSE 293/02 ELECTRONICS MODULE TEST E1 HIGHER TIER AM WEDNESDAY, 19 May 2010 45 minutes For s use Total Mark ADDITIONAL MATERIALS In addition to this examination
More informationElectronics & Control
Electronics & Control Analogue Electronics Introduction By the end of this unit you should be able to: Know the difference between a series and parallel circuit Measure voltage in a series circuit Measure
More informationPTC-resistor relay type MS 220 K and MSR 220 K PTC-resistor trip device
MINIPAN digital panel meters, temperature- and mains controlling, special purpose instruments for customer requirements www.ziehl.com Operating manual PTC-resistor relay type MS 220 K and MSR 220 K PTC-resistor
More informationSTANDARD WIRING DIAGRAMS FOR SMART MODEL 20
SMART SERIES CODING SYSTEM FOR AV ACTUATOR WIRING DIAGRAMS There are 3 elements to the wiring codes used in AVA electric actuators: WIRING CODE 1 3 Wire system, single pole double throw, switching the
More information2. What is the difference between an analogue watch and a digital watch? (2)
ELECTRONICS HOMEWORK 1 1. Make a table with two columns headed Analogue and Digital. Place the following electronic devices into one of the two columns: (4) 7 segment display, motor, solenoid, bulb, LED,
More informationSPINE ROAD HIGH SCHOOL TECHNOLOGY TEST 2 GRADE 9 SEPTEMBER 2017 EXAMINER: MRS N GOVENDER MODERATOR: MR LUKIE TIME: 1 HOUR 30 MINUTES INSTRUCTIONS
SPINE ROAD HIGH SCHOOL TECHNOLOGY TEST 2 GRADE 9 SEPTEMBER 2017 EXAMINER: MRS N GOVENDER MODERATOR: MR LUKIE TIME: 1 HOUR 30 MINUTES INSTRUCTIONS 1. Answer all questions 2. Rule off after each question.
More informationWallace Hall Academy Physics Department. Electricity. Pupil Notes Name:
Wallace Hall Academy Physics Department Electricity Pupil Notes Name: 1 Learning intentions for this unit? Be able to state that there are two types of charge; positive and negative Be able to state that
More informationQ2. Figure 1 shows the oscilloscope trace an alternating current (a.c.) electricity supply produces.
SERIES AND PARALEL CIRCUITS Q1. A student set up the electrical circuit shown in the figure below. (a) The ammeter displays a reading of 0.10 A. Calculate the potential difference across the 45 Ω resistor.
More informationSeries and Parallel Circuits Basics 1
1 Name: Symbols for diagrams Directions: 1. Log on to your computer 2. Go to the following website: http://phet.colorado.edu/en/simulation/-construction-kit-dc Click the button that says Play with sims
More informationSTANDARD WIRING DIAGRAMS FOR SMART MODEL 20
CODING SYSTEM FOR AV ACTUATOR WIRING DIAGRAMS There are 3 elements to the wiring codes used in AVA electric actuators: WIRING CODE 1 3 Wire system, single pole double throw, switching the live SPDT 2 3
More informationSmartZone-2 & SmartZone-4
SmartZone-2 & SmartZone-4 Quick-Start Guide UPDATED 2011-7-26 This guide is intended to give the installer a brief set of instructions about how to set up the XCI Zoning SmartZone System. For more detailed
More informationFinal Reg Current and Circuits Review SHORT ANSWER. Write the word or phrase that best completes each statement or answers the question.
Final Reg Current and Circuits Review SHORT ANSWER. Write the word or phrase that best completes each statement or answers the question. 1) How much energy does a 100-W light bulb use in 8.0 hours? 1)
More informationBFS / BFSM SERIES Installation & Maintenance Manual
Introduction: The BFS / BFSM series electric actuators have battery backup modules for fail safe operation. The BFS series is for two position control and the BFSM series is for proportional control, both
More informationELEXBO. Electrical - Experimentation Box
ELEXBO Electrical - Experimentation Box 1 Table of contents 2 Introduction...3 Basics...3 The current......4 The voltage...6 The resistance....9 Measuring resistance...10 Summary of the electrical values...11
More informationTemperature activated switch
Build instructions, circuit explanation and example applications Issue 1.5 Product information: www.kitronik.co.uk/quicklinks/2113/ TEACHER Temperature activated switch Introduction About the project kit
More informationis connected in parallel to the input of an electronic circuit that switches the mains supply to the heating element in the oven on or off.
1 This question is about the use of a thermistor fitted inside a domestic oven as a temperature sensor in a potential divider circuit. Fig. 2.1 shows the potential divider circuit in which the component
More informationDATE: NAME: CLASS: Drawing Circuit Diagrams
CHAPTER 8 BLM 315 Drawing Circuit Diagrams Goal Practise drawing circuit diagrams. For each of the following circuit illustrations, draw its corresponding circuit diagram and answer the questions that
More informationCircuit Analysis and Ohm s Law
Excerpt from Circuit Analysis and Ohm s Law By Robert Cecci iii Preview The following is a sample excerpt from a study unit converted into the Adobe Acrobat format. A sample online exam is available for
More informationpotential difference resistance current
1 (a) The following electrical quantities are often used when analysing circuits. Draw a straight line from each quantity on the left-hand side to its correct units on the right-hand side. potential difference
More informationCode. Edition 04/2013. CPA Screw Air Compressors. Parts List Book
Code 2205 1084 06 Edition 04/2013 CPA7.5-10-15-20 Screw Air Compressors Parts List Book REF. PART NUM. QTY. NAME REF. PART NUM. QTY. NAME 1095 2205 1020 83 1 BASE 1195 2205 1053 83 1 PANEL 1100 2205 1028
More informationCONTENTS. SAFETY PRECAUTIONS: Before use, read the following safety precautions
CONTENTS [1] SAFETY PRECAUTIONS: Before use, read the following safety precautions 2 [2] APPLICATION AND FEATURES 5 [3] NAME OF COMPONENT UNITS 6 [4] DESCRIPTION OF FUNCTIONS 8 [5] MEASUREMENT PROCEDURE
More informationPROGRAMED ANALOG CONTROL MODULE
PROGRAMED ANALOG CONTROL MODULE FEATURES Two channel conversion Transformer isolation onboard Isolated 24V AC for Velocity sensor APPLICATIONS Velocity sensor conversions Velocity sensor linearization
More informationBlue Point Engineering
Blue Point Engineering Instruction I www.bpesolutions.com Pointing the Way to Solutions! Animatronic Wizard - 3 Board (BPE No. WAC-0030) Version 3.0 2009 Controller Page 1 The Wizard 3 Board will record
More informationELEC2 (JUN15ELEC201) General Certificate of Education Advanced Subsidiary Examination June Further Electronics TOTAL. Time allowed 1 hour
Centre Number Surname Candidate Number For Examiner s Use Other Names Candidate Signature Examiner s Initials Question Mark Electronics General Certificate of Education Advanced Subsidiary Examination
More informationRepair Parts List REFRIGERATOR MODEL NUMBER RC24CN-3AI MANUFACTURING NUMBER 3N80B
REFRIGERATOR Repair Parts List MODEL NUMBER RC24CN-3AI MANUFACTURING NUMBER 3N80B When requesting service or ordering parts, always provide the following information: - Product Type - Part Number - Model
More informationHEAT ACTIVATED SWITCH KIT
TEACHING RESOURCES SCHEMES OF WORK DEVELOPING A SPECIFICATION COMPONENT FACTSHEETS HOW TO SOLDER GUIDE REACT TO THE TEMPERATURE WITH THIS HEAT ACTIVATED SWITCH KIT Version 2.1 Heat Activated Switch Teaching
More informationMicro-ISO Automotive Relay. (Unit: mm inch)
Micro-ISO Automotive Relay CM RELAYS Flux tight/sealed.. FEATURES Micro-ISO type terminals and small size Wide line-up Compact and high-capacity switching... TYPICAL APPLICATIONS
More informationMICRO-ISO AUTOMOTIVE RELAY
MICRO-ISO AUTOMOTIVE RELAY RELAYS Plug-in type PC board type RoHS compliant FEATURES Micro-ISO type terminals Small size: mm(l) mm(w) mm(h). inch(l). inch(l). inch(h) Wide line-up PC board and Plug-in
More informationRamp/Soak Temperature Controller REX-P250
EX-P0 General The EX-P0 is a high performance ramp/soak controller with a storage capacity of segments in patterns. Each pattern consists of up to segments and patterns can be linked for maximum pattern
More informationSimple Circuits Experiment
Physics 8.02T 1 Fall 2001 Simple Circuits Experiment Introduction Our world is filled with devices that contain electrical circuits in which various voltage sources cause currents to flow. We use radios,
More informationIMP-2A ELECTRODE IMPEDANCE TESTER SINGLE CHANNEL
MicroProbes for Life Science IMP-2A ELECTRODE IMPEDANCE TESTER SINGLE CHANNEL User Instructions Version: October, 2015 18247-D Flower Hill Way Gaithersburg, MD 20879 Phone: +1 301 330-9788 Fax: +1 301
More informationELE.B: Original Assignment Resistors in Series Classwork Homework
ELE.B: Original Assignment Resistors in Series Classwork 1. A 3 Ω resistor is connected in series to a 6 Ω resistor and a 12-V battery. What is the current in each of the resistors? What is the voltage
More informationCFD-S23 SERVICE MANUAL Ver 1.0 1998. 08 SUPPLEMENT - 1 File this Supplement with the Service Manual. Subject : r EAST EUROPEAN AND RUSSIAN MODEL HAS BEEN ADDED r CHANGE OF BOARDS AC INLET BOARD : 1-666-267-11
More informationCAUTION All safety information must be followed as provided in Service Manual
Domestic Microwave Technical Information AMV564BC* MMV507BC* JMV808BC* Due to possibility of personal injury or property damage, always contact an authorized technician for servicing or repair of this
More information4. An overheated resistor is usually a symptom of a problem rather than its cause.
TRUE/FALSE 1. Voltage can exist only where there is a current path. Page: 1 2. An open circuit condition is one where R =. 3. One ampere equals 1 joule per second. 4. An overheated resistor is usually
More informationVCE PHYSICS AOS 2 UNIT 3. Circuit Design and Application
VCE PHYSICS AOS 2 UNIT 3 Circuit Design and Application The Components design, investigate and analyse circuits for particular purposes using technical specifications related to potential difference (voltage
More informationFig The potential difference across each strip is 12 V when a current of 2.0 A passes through it. of one strip of the heater.
1 This question is about possible heating circuits used to demist the rear window of a car. The heater is made of 8 thin strips of a metal conductor fused onto the glass surface. Fig. 2.1 shows the 8 strips
More informationTurn Signal Light Circuit
34 Turn Signal Light Circuit DSCRIPTION The turn signal flasher relay turns on when it receives signals from the headlight dimmer switch integrated with the turn signal switch, causing the turn signal
More informationPHYS 102 Quiz Problems Chapter 27 : Circuits Dr. M. F. Al-Kuhaili
PHYS 102 Quiz Problems Chapter 27 : Circuits Dr. M. F. Al-Kuhaili 1. (TERM 002) (a) Calculate the current through each resistor, assuming that the batteries are ideal. (b) Calculate the potential difference
More informationElectric Currents 2 D V. (1)
Name: Date: Electric Currents 2. A battery is connected in series with a resistor R. The battery transfers 2 000 C of charge completely round the circuit. During this process, 2 500 J of energy is dissipated
More informationAC 01.2 HART Technical data Actuator controls
General information AC 01.2 actuator controls for controlling multi-turn actuators of the SA/SAR.2 type range and part-turn actuators of the SQ/SQR type range with interface. Power supply Standard voltages
More informationHome Map Projects Construction Soldering Study Components 555 Symbols FAQ Links
Home Map Projects Construction Soldering Study Components 555 Symbols FAQ Links Circuit Symbols Wires Supplies Output devices Switches Resistors Capacitors Diodes Transistors Audio & Radio Meters Sensors
More informationCAUTION All safety information must be followed as provided in Service Manual
Domestic Microwave Technical Information AMV564BA* Due to possibility of personal injury or property damage, always contact an authorized technician for servicing or repair of this unit. Refer to Service
More information1 Ω = 1 V A -1 ELECTRICAL RESISTANCE (R) 1. Candidates should be able to:
ELECTRCAL RESSTANCE (R) 1 Candidates should be able to: Define RESSTANCE. Of a conductor or component is a measure of its opposition to the flow of charge (i.e. to electric current). Select and use the
More informationSensor, Op-amp comparator, and output revision.
Sensor, Op-amp comparator, and output revision. 1). For growing tropical plants it is necessary to ensure that the greenhouses are maintained at a minimum temperature at all times. An electronic systems
More informationThe equation which links current, potential difference and resistance is:
Q1.An electrical circuit is shown in the figure below. (a) The current in the circuit is direct current. What is meant by direct current? Tick one box. Current that continuously changes direction. Current
More informationOwner's Manual Applications & Operating Instructions, Trouble-shooting, Specifications & Warranty
01/14/2013 RevA Owner's Manual Applications & Operating Instructions, Trouble-shooting, Specifications & Warranty GENERAL INFORMATION - The Pro-VCS ( Programmable Voltage-Controlled Switch ) consists of
More informationFixed - Over/Under voltage limits, ( ) U N respectivity Link selectable - 5 min or 10 min delay. Fixed limits
Features 71.11.8.230.0010 71.11.8.230.1010 1 - Phase 230 V Over & Under voltage monitoring relays 71.11.8.230.0010 - Fixed Over & Under voltage detection - Link selectable 5 or 10 minute lock-out delay
More informationUnit 1 Electronics Name: Form:
Unit 1 Electronics Name: Form: Electronics Electronics is the study of components and techniques used to be able to build circuits controlled by electricity. An electronic system uses discrete components.
More informationRepair Parts List REFRIGERATOR MODEL NUMBER JS48SEDBDA. When requesting service or ordering parts, always provide the following information:
Repair Parts List REFRIGERATOR MODEL NUMBER JS48SEDBDA When requesting service or ordering parts, always provide the following information: - Product Type - Part Number - Model Number - Part Description
More informationDesign and Technology
E.M.F, Voltage and P.D E.M F This stands for Electromotive Force (e.m.f) A battery provides Electromotive Force An e.m.f can make an electric current flow around a circuit E.m.f is measured in volts (v).
More information2.6 RESISTORS ATTRIBUTES
2.6 RESISTORS ATTRIBUTES 1. Resistance named value: the value written on the body of the resistor in Ω. 2. Named power: the maximum thermal power the resistor can produce towards the environment, without
More informationintroduction to Digital Electronics Install the Arduino IDE on your laptop if you haven t already!
introduction to Digital Electronics Install the Arduino IDE 1.8.5 on your laptop if you haven t already! Electronics can add interactivity! Any sufficiently advanced technology is indistinguishable from
More informationFixed - Over/Under voltage limits, ( ) U N respectivity Link selectable - 5 min or 10 min delay. Fixed limits
Features 71.11.8.230.0010 71.11.8.230.1010 1 - Phase 230 V Over & Under voltage monitoring relays 71.11.8.230.0010 - Fixed Over & Under voltage detection - Link selectable 5 or 10 minute lock-out delay
More informationLab 06: Ohm s Law and Servo Motor Control
CS281: Computer Systems Lab 06: Ohm s Law and Servo Motor Control The main purpose of this lab is to build a servo motor control circuit. As with prior labs, there will be some exploratory sections designed
More information! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless testing requires power.
Domestic Microwave Technical Information Over-The-Range Convection Microwave Models AMV404AAB/W/Q MMV405AAB/W/Q/S Due to possibility of personal injury or property damage, always contact an authorized
More informationUNIT E1 (Paper version of on-screen assessment) A.M. WEDNESDAY, 8 June hour
Candidate Name GCSE 46/0 Centre Number Candidate Number 0 ELECTRONICS UNIT E (Paper version of on-screen assessment) A.M. WEDNESDAY, 8 June 20 hour For s use 46 0000 Total Mark ADDITIONAL MATERIALS Information
More informationRangefinder Servo and LED Controller Board Hyperdyne Labs, 2001
Rangefinder Servo and LED Controller Board Hyperdyne Labs, 2001 http://www.hyperdynelabs.com *** DO NOT HOOK UP THE SERVO INCORRECTLY. READ BELOW FIRST *** Overview The rangefinder servo and LED board
More informationVoltage, Current and Resistance
Voltage, Current and Resistance Foundations in Engineering WV Curriculum, 2002 Foundations in Engineering Content Standards and Objectives 2436.8.3 Explain the relationship between current, voltage, and
More informationInstallation/operation instructions. Insulation monitor type SIM-Q/SIM-Q LF D (UK) Measuring range 1...0Mohm or 10...
Installation/operation instructions Insulation monitor type SIM-Q/SIM-Q LF Monitoring of insulation resistance on an AC network Working voltage up to 690V AC, withstands up to 1000V DC Measuring range
More informationA piece of wire of resistance R is cut into five equal parts. These parts are then connected in
Page 221»Exercise» Question 1: A piece of wire of resistance R is cut into five equal parts. These parts are then connected in parallel. If the equivalent resistance of this combination is R', then the
More informationTOP SERVO SIGNAL 5 SERVO SIGNAL 3 SERVO SIGNAL 4 SERVO SIGNAL 6 T B T B T B T B T B SERVO TRIGGER 1 BOTTOM
Micro Miniatures Servo Controller Channel Location of connections and switches TOP SERVO SIGNAL SERVO SIGNAL 7 SERVO SIGNAL 6 SERVO SIGNAL 5 SERVO SIGNAL SERVO SIGNAL SERVO SIGNAL SERVO SIGNAL SIGNAL COMMON
More informationBlue Point Engineering
Blue Point Engineering Instruction I www.bpesolutions.com Pointing the Way to Solutions! Puppet - II+ Controller (BPE No. PCA-0001) Servo Position Adjustment EEPROM Digital Button Power 5 Vdc Playback
More informationOSCILLOSCOPES. Oscilloscopes CS-5300 SERIES RS-232C OPTION OPTION CS-5370P/5370/5350 FEATURES OUTLINE. Photo: CS-5370P
Oscilloscopes 100MHz 2-Channel Programmable Oscilloscope ( With Digital Readout / Cursor) CS-5370P CS-5370 100MHz 3-Channel Oscilloscope ( With Digital Readout / Cursor) 50MHz 3-Channel Oscilloscope (
More informationRepair Parts List REFRIGERATOR MODEL NUMBER JBR2286KES. When requesting service or ordering parts, always provide the following information:
Repair Parts List REFRIGERATOR MODEL NUMBER JBR2286KES When requesting service or ordering parts, always provide the following information: - Product Type - Part Number - Model Number - Part Description
More informationELECTRICAL TEST WORKSHOP MANUAL
ELECTRICAL TEST WORKSHOP MANUAL GB reference : 755711 DC/ATR 03/2001 CONTENTS 1. ELECTRICAL TESTS... 5 The test apparatus:...5 Wires:... 7 Resistances:... 7 Bulbs:... 8 Saddle control:... 8 Magneto:...
More information2: The resistivity of copper is Ω.m. Determine the resistance of a copper wire that is 1.3 m long and has a diameter of 2.1 mm.
Chapter 20 Discussion January-03-15 8:58 PM Electric Circuits Discussion Questions 1: A current of 12 A flows for 2.5 minutes to charge a battery. How much charge is transferred to the battery in this
More informationPARTS CATALOG R410A. September 2008 AIR TO WATER HEAT PUMP. No. OCB439 REVISED EDITION-A. [Service Ref.] [model name]
AIR TO WATER HEAT PUMP PARTS CATALOG R40A [model name] PUHZ-W50VHA PUHZ-W5VHA PUHZ-HWYHA PUHZ-HW40VHA PUHZ-HW40YHA [Service Ref.] PUHZ-W50VHA PUHZ-W5VHA PUHZ-HWYHA PUHZ-HW40VHA PUHZ-HW40YHA September 00
More informationBasic Electricity Principles & Boiler Wiring Fundamentals. Presented by Steve Connor April 20, 2016
Basic Electricity Principles & Boiler Wiring Fundamentals Presented by Steve Connor April 20, 2016 Today s Topics 1 Some basics & historical background Electricity and its current types The advantages
More informationExam 2. Name: Class: Date: Multiple Choice Identify the choice that best completes the statement or answers the question.
Name: Class: Date: Exam 2 Multiple Choice Identify the choice that best completes the statement or answers the question. 1. For this circuit, which of these equations is correct? a. 80-1I 2-20I 2-30I 1
More informationBoulder W Class A Stereo Power Amplifier
Boulder 2060 600 W Class A Stereo Power Amplifier Owners Manual V1.0 10/10/97 TABLE OF CONTENTS GETTING STARTED Placement of the 2050 Power amplifier......................................... 1-1 Connecting
More informationPhysicsAndMathsTutor.com 1
PhysicsAndMathsTutor.com 1 1. The figure below shows a circuit containing a battery of e.m.f. 12 V, two resistors, a light-dependent resistor (LDR), an ammeter and a switch S. The battery has negligible
More informationNational Physics. Electricity and Energy Homework. Section 2 Electrical Power
National Physics Electricity and Energy Homework Section 2 Electrical Power Homework 1 : Energy Changes and Power 1. Appliances convert electrical energy into other forms of energy. State the useful energy
More informationBasic Characteristics Data
Basic Characteristics Data Basic Characteristics Data Model Circuit method Material PCB/Pattern Single sided Double sided KRE-2A Diode FR-4 Yes KRE-4A Diode FR-4 Yes KR-4 1 Terminal Blocks 2 Functions
More information8.0 Ω 12.0 Ω. When the switch S is open, show that the potential difference between the points X and Y is 7.2 V.
1. The figure below shows a circuit containing a battery of e.m.f. 12 V, two resistors, a light-dependent resistor (LDR), an ammeter and a switch S. The battery has negligible internal resistance. 8.0
More informationCircuits: Light-Up Creatures Student Advanced version
Circuits: Light-Up Creatures Student Advanced version In this lab you will explore current, voltage and resistance and their relationships as given by the Ohm s law. You will also explore of how resistance
More informationPROGRAMMABLE CFE PULLER
PROGRAMMABLE CFE PULLER Manual Pulling of PE tubing is a critical step in CFE fabrication. Getting constant shapes in CFE is difficult and to achieve a high success rate in pulling CFE requires patience
More information*X036/12/01* X036/12/01 TECHNOLOGICAL STUDIES HIGHER NATIONAL QUALIFICATIONS 2013 TUESDAY, 21 MAY 1.00 PM 4.00 PM
X036/12/01 ATIOAL QUALIFICATIOS 2013 TUESDA, 21 MA 1.00 PM 4.00 PM TECHOLOGICAL STUDIES HIGHER 200 marks are allocated to this paper. Answer all questions in Section A (120 marks). Answer two questions
More informationApplication Note CTAN #305
Application Note CTAN #305 This Application Note is pertinent to the Unidrive SP, GP20 and Affinity Families Creating a Custom Motor Overtemperature Trip The Unidrive SP has facilities on Analog Input
More informationRepair Parts List REFRIGERATOR MODEL NUMBER JCD2290HEW. When requesting service or ordering parts, always provide the following information:
Repair Parts List REFRIGERATOR MODEL NUMBER JCD2290HEW When requesting service or ordering parts, always provide the following information: - Product Type - Part Number - Model Number - Part Description
More informationResistance and Ohm s law
Resistance and Ohm s law Objectives Characterize materials as conductors or insulators based on their electrical properties. State and apply Ohm s law to calculate current, voltage or resistance in an
More informationGive one or two examples of electrical devices that you have personally noticed getting warm when they are turned on.
Resistors We begin by learning how to read the values of resistors and to measure the values using a digital multimeter (DMM). Resistors are the most common and simplest electrical component. In an electrical
More informationLED Driver Compact fixed output
w LED Driver Driver LCI 100W 900mA 1750mA TOP C TOP series Product description Fixed output built-in LED Driver Constant current LED Driver Output current settable 900 1,750 ma Max. output power 100 W
More informationBook page Syllabus 2.8, 2.9, Series and parallel circuits
Book page 77 79 Syllabus 2.8, 2.9, 2.14 Series and parallel circuits Find the Fib! (1) The symbol for a bulb is (2) In a parallel circuit potential difference is the same as the supply voltage on all branches.
More informationPARTS CATALOG R410A. January 2012 PUHZ-HW112YHA PUHZ-HW112YHA-BS PUHZ-HW140VHA PUHZ-HW140VHA-BS PUHZ-HW140YHA PUHZ-HW140YHA-BS PUHZ-HW140VHA2R2-BS
AIR TO WATER HEAT PUMP PARTS CATALOG [Model name] PUHZ-W50VHA PUHZ-W50VHA-BS PUHZ-W85VHA PUHZ-W85VHA-BS PUHZ-HWYHA PUHZ-HWYHA-BS PUHZ-HWYHA PUHZ-HWYHA-BS PUHZ-HW0VHA PUHZ-HW0VHA-BS PUHZ-HW0YHA PUHZ-HW0YHA-BS
More informationDIGITAL MULTIMETER OPERATING INSTRUCTIONS MODEL CDM-35. Part No
DIGITAL MULTIMETER MODEL CDM-35 Part No.4500055 OPERATING INSTRUCTIONS 0304 The Meter may be hung on a wall, or supported as shown, depending upon which support is used. The probes may be located as shown,
More informationA B. 1 (a) (i) Fig shows the symbol for a circuit component. Fig Name this component. ... [1]
(a) (i) Fig.. shows the symbol for a circuit component. Fig.. Name this component.... [] (ii) In the space below, draw the symbol for a NOT gate. (b) Fig..2 shows a digital circuit. [] C D E Fig..2 Complete
More informationCircuitry II. Name: Date: Section C D F. Mr. Alex Rawson Physics
Name: Date: Section C D F Circuitry II Mr. Alex Rawson Physics 1. Three resistors of 100, 140, and 80 are placed in a series circuit. a. Find the equivalent resistance. (Your answer should be between 0
More information