HIGH PERFORMANCE CONTROLLERS BASED ON REAL PARAMETERS TO ACCOUNT FOR PARAMETER VARIATIONS DUE TO IRON SATURATION
|
|
- Augustine Singleton
- 5 years ago
- Views:
Transcription
1 2013 NDIA GROUND VEHICLE SYSTEMS ENGINEERING AND TECHNOLOGY SYMPOSIUM VEHICLE ELECTRONICS AND ARCHITECTURE (VEA MINI-SYMPOSIUM AUGUST 21-22, TROY, MICHIGAN HIGH PERFORMANCE CONTROLLERS BASED ON REAL PARAMETERS TO ACCOUNT FOR PARAMETER VARIATIONS DUE TO IRON SATURATION Jorge G. Cintron-Rivera 1, Ph.D. Caniate Shanelle N. Foster 1, Ph.D. Caniate Wesley G. Zanarelli 2, Ph.D. an Elias G. Strangas 1, Ph.D. 1 Michigan State University -Department of ECE - East Lansing, MI Avance Propulsion - U.S. ARMY TARDEC - Warren, MI 8397 ABSTRACT With the increase in electric power on military groun vehicle platforms, electrically riven accessories are replacing existing hyraulic, belt, an gear-riven loas. Permanent Magnet Synchronous Machines (PMSM are often selecte to rive these accessories, an are uner consieration for the main engine generator, ue to their torue ensity an efficiency being among the highest available. To maximize the efficiency of a PMSM, accurate knowlege of its parameters is reuire across the entire operating range. Efficient control of the onboar electric rives will help reuce fuel consumption in the groun vehicle fleet. This paper presents the effects of iron saturation on the performance of a PMSM rive. Iron saturation epens on the amount of current injecte into the motor an it restricts the amount of flux linkage that can be generate. PMSMs are controlle using a two axis space vector representation. Ieally, the control is ecouple, such that the flux linkage prouction in one axis is not affecte by the current in the other axis. However, iron saturation alters this behavior an the flux linkages become epenent on both axis currents. This paper emonstrates this phenomenon by parametric experimental characterization of two permanent magnet synchronous motors. A simple but epenable metho to approximate an inclue all the saturation effects, base on real parameters, is propose. The effectiveness of the propose metho is valiate through a simulation using the experimentally extracte parameters. INTRODUCTION Future Army groun vehicle platforms are expecte to generate significantly greater levels of onboar electric power, [1]. While traitional alternators can source approximately 600A current at 28VDC (16.8kW, emerging high-voltage generators irectly riven by the engine s crankshaft can prouce nearly an orer-of-magnitue increase in electric power ( kW. Benefits of the increase electric power inclue greater electrification of vehicle loas an intelligent power management, incluing some of the most significant loas such as the main engine cooling fan(s an air conitioning compressor. A key challenge remains to ensure that these loas along with the generator operate at maximum efficiency, [2]. Instea of being riven through a set of gears, a belt rive, or a hyraulic system, electrifie accessories len themselves well to variable spee operation an intelligent power management strategies, [3]-[5]. This allows them to run at varying operating points regarless of the main engine spee an they can be power limite on eman to support higher priority loas. While electric rives are generally able to efficiently convert electrical to mechanical power biirectionally, there are still opportunities to further improve this conversion efficiency, reucing the overall thermal buren on the vehicle cooling system. The key to improving the performance an efficiency of a motor rive is to evelop controllers base on real parameters, [6]-[7]. Such controllers are capable of acknowleging the parameters non-ieal behaviors an using them to operate as efficiently as possible, [8]. In [9], a look-up table to implement Maximum Torue Per Amp (MTPA control is propose. This metho oes not UNCLASSIFIED: Distribution Statement A. Approve for public release.
2 Report Documentation Page Form Approve OMB No Public reporting buren for the collection of information is estimate to average 1 hour per response, incluing the time for reviewing instructions, searching existing ata sources, gathering an maintaining the ata neee, an completing an reviewing the collection of information. Sen comments regaring this buren estimate or any other aspect of this collection of information, incluing suggestions for reucing this buren, to Washington Heauarters Services, Directorate for Information Operations an Reports, 1215 Jefferson Davis Highway, Suite 120, Arlington VA Responents shoul be aware that notwithstaning any other provision of law, no person shall be subject to a penalty for failing to comply with a collection of information if it oes not isplay a currently vali OMB control number. 1. REPORT DATE 25 JUL REPORT TYPE Journal Article 3. DATES COVERED to TITLE AND SUBTITLE HIGH PERFORMANCE CONTROLLERS BASED ON REALPARAMETERS TO ACCOUNT FOR PARAMETER 6. AUTHOR(S Jorge Cintron-Rivera; Shanelle Foster; Wesley Zanarelli; Elias Strangas 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 5. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME(S AND ADDRESS(ES Michigan State University,Department of ECE,26 Auitorium R,East Lansing,Mi, SPONSORING/MONITORING AGENCY NAME(S AND ADDRESS(ES U.S. Army TARDEC, 6501 East Eleven Mile R, Warren, Mi, PERFORMING ORGANIZATION REPORT NUMBER ; # SPONSOR/MONITOR S ACRONYM(S TARDEC 11. SPONSOR/MONITOR S REPORT NUMBER(S # DISTRIBUTION/AVAILABILITY STATEMENT Approve for public release; istribution unlimite 13. SUPPLEMENTARY NOTES GROUND VEHICLE SYSTEMS ENGINEERING AND TECHNOLOGY SYMPOSIUM (GVSETS, SET FOR AUG , ABSTRACT With the increase in electric power on military groun vehicle platforms, electrically riven accessories are replacing existing hyraulic, belt, an gear-riven loas. Permanent Magnet Synchronous Machines (PMSM are often selecte to rive these accessories, an are uner consieration for the main engine generator, ue to their torue ensity an efficiency being among the highest available. To maximize the efficiency of a PMSM, accurate knowlege of its parameters is reuire across the entire operating range. Efficient control of the onboar electric rives will help reuce fuel consumption in the groun vehicle fleet. This paper presents the effects of iron saturation on the performance of a PMSM rive. Iron saturation epens on the amount of current injecte into the motor an it restricts the amount of flux linkage that can be generate. PMSMs are controlle using a two axis space vector representation. Ieally, the control is ecouple, such that the flux linkage prouction in one axis is not affecte by the current in the other axis. However, iron saturation alters this behavior an the flux linkages become epenent on both axis currents. This paper emonstrates this phenomenon by parametric experimental characterization of two permanent magnet synchronous motors. A simple but epenable metho to approximate an inclue all the saturation effects, base on real parameters, is propose. The effectiveness of the propose metho is valiate through a simulation using the experimentally extracte parameters. 15. SUBJECT TERMS
3 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF a. REPORT unclassifie b. ABSTRACT unclassifie c. THIS PAGE unclassifie ABSTRACT Public Release 18. NUMBER OF PAGES 9 19a. NAME OF RESPONSIBLE PERSON Stanar Form 298 (Rev Prescribe by ANSI St Z39-18
4 Proceeings of the 2013 Groun Vehicle Systems Engineering an Technology Symposium (GVSETS inclue saturation effects. PMSMs are usually operate uner saturation [10], neglecting these effects can lea to controller performance egraation [11]. All saturation effects were inclue in both controllers propose in [12] an [13]. In [12], signal injection was use to etermine the parameters neee to evelop lookup tables an in [13], finite element analysis was use to ientify the machine parameters. Neither controller, however, is capable of operating in the fiel weakening region. In this paper, a metho to approximate the parameters of a PMSM is propose. The metho is base on experimental ata an it inclues the saturation effects using piecewise linear functions. The metho was valiate, in the MTPA an fiel weakening regions, using simulations base on real parameters from two 125kW PMSMs. BACKGROUND THEORY AND MODELING Permanent magnet synchronous machines are moele using the euivalent two axis moel shown in Figure 1, referre to as the synchronous frame of reference. This moel is obtaine by applying the Park s transformation matrix to the three phase stator uantities. i v Rs L e The complete machine moel after Park s transformation is given by euations (1 - (5. i v Rsi L el i Rsi e t t (1 i v Rsi L e Rsi e t t (2 Li (3 pm ( v L Rs L Figure 1: Euivalent two axes moel for a PMSM. e e pm 3P T i i (5 Where, are the currents an voltages in the irect an uarature axes. are the flux linkages ue to the permanent magnets an the corresponing axes currents. are the irect an uarature axis inuctances, is the electrical spee of the motor an T is torue Figure 2 shows the orientation frame to which the motor moel, (1-(5, is referre. In this orientation, the flux linkage ue to the magnets lies on the positive -axis, an torue is only prouce by the uarature current. The irect axis current is use as a fiel weakening mechanism an in the case of an interior permanent magnet machine it enables the prouction of reluctance torue. For motoring, PMSMs are generally operate in the secon uarant of the space plane, Figure 2, to perform fiel weakening an evelop the magnetic an reluctance torues. This classical moel (1-(5 is base on ieal conitions where the effects of iron losses, self an cross saturation, are neglecte. To stuy the effects of losses an iron saturation in PMSMs the classical moel is extene in orer to inclue these effects. When an saturate the iron paths in each corresponing axis, the flux linkages prouce by the magnetizing currents are no longer ecouple as shown in the ieal moel (3 an (. Instea, the flux linkages become couple to both axis currents, this coupling effect can be moele as follows, i, i L ( i i L ( i, i i (6 pm i, i L ( i i L ( i, i i (7 where, an are the baseline inuctances for each of the axes. They represent the corresponing axis selfinuctance as a function of the axis current an are calculate assuming no cross saturation from the other-axis current, [6]. an are the cross s axis I s voltage vector i V current vector v x i i,0 L ( i i x x x x x x x Lxyiy v i pm axis Figure 2: Vector orientation use for moel evelopment an control techniues. ( i, i L ( i i L i x x y x x x xy y Figure 3: Self an cross saturation of the flux linkages i x UNCLASSIFIED Page 2 of 9
5 Proceeings of the 2013 Groun Vehicle Systems Engineering an Technology Symposium (GVSETS coupling inuctances for each axis an a the cross saturation effects to the machine moel. This self an cross saturation behavior is illustrate in Figure 3, where the x an y variables represent the an -axis Euations (6 an (7 coul be written in a variety of ways to moel the effect of both currents on the an -axis fluxes. The formulation use in this paper assigns all the cross coupling to the uasi-mutual inuctances an, the rest of the saturation to an, an assumes no effect of saturation of the flux ue to magnets, without ecreasing the moel accuracy. The machine moel incluing the saturation effects is calculate by substituting (6 an (7 into (1-(5. After some algebraic manipulation, the moifie machine moel is given by (8-(10. i i v Rsi L ( i L ( i, i t t L ( i i L ( i, i i e i i v Rsi L ( i L ( i, i t t L ( i i L i ( i, i e pm (8 (9 3P T i, i i i, i i (10 PARAMETER IDENTIFICATION PROCESS This paper is aime to fin an uantify the PMSM parameters, incluing the self an cross saturation effects, in orer to evelop a high performance controller. Knowlege of the non-ieal parameters is essential to evelop a highly efficient motor rive, [10]. To uantify this behavior, the parameter ientification metho propose in [6] was use. This metho is capable of extracting the parameters, incluing the non-ieal characteristics, by collecting an processing experimental ata. Similar methos for parametric ientification have been propose, [7] an they follow the same characterization principle. The ientification process is ivie into two main proceures: Experimental ata collection, as shown in Figure, an off-line ata processing. During the characterization process, the machine is stuie over its entire current operating range. The experimental ata is obtaine at a particular spee, an all possible current an angle combinations are applie to the machine. At every current/angle combination, the phase voltage information, experimental line currents, an rotor position are recore. Then, this information is processe off-line to accurately etermine the machine flux linkages, an e PMSM ABC Inverter V c, using (11 an (12. Given that the information collecte comes from experimental ata, the saturation effects an nonlinear behavior of the PMSM are capture. v i Rs i, i (11 ia, ib, ic Dyno DSP system Controller Boar s i, i e Spee Controlle ata logging an post-process Figure : Experimental Setup e CAN ata flow i R v (12 The flux information obtaine is sufficient to evelop a high performance controller, since an inclue the non-ieal characteristics of the machine. The non-ieal inuctance values can be calculate from this information. EXPERIMENTAL CHARACTERIZATION Two PMSMs, a motor an a generator, were characterize in orer to stuy the effects of iron saturation. The characteristics for each machine are given in table 1. Parameters Motor Generator Rate power 125 kw 125 kw Rate spee 1500 RPM 1900 RPM Max spee 5000 RPM 3000 RPM Line voltage Max current No. poles 8 Table 1: PMSM parameters The parameters for both machines were etermine at 700 RPM as shown in figures 5-8. This spee is sufficient to generate a measurable back-emf voltage an it is below the base spee. Therefore, it is possible to collect experimental ata for all the rate current combinations of an. UNCLASSIFIED Page 3 of 9
6 L (i, L (i, (i, (i, L (i, L (i, (i, (i, Proceeings of the 2013 Groun Vehicle Systems Engineering an Technology Symposium (GVSETS The experimental results in Figures 5-8, emonstrate that self an cross-saturation are non-ieal characteristics that cannot be ignore or assume to be negligible. For the motor, the flux linkage along the -axis ha as much as 38.5% variation ue to cross saturation, while the -axis ha as much as 23.7% variation. The generator behavior is similar, with flux variations as high as 31.% on the -axis flux an 1.5% on the -axis ue to cross saturation. These non-ieal parametric variations have a negative impact on the torue prouction of the machine, since the torue is irectly proportional to the flux linkages, as shown in (10. Efficiency is also affecte, as the parametric variations will etune the motor controller. For a given operating conition, the controller will not inject the optimal currents to generate the esire torue. 125 kw PM Motor, -axis flux linkage 125 kw PM Genertator, -axis flux linkage Saturation ue to i i x kw PM Genertator, -axis Inuctance Saturation ue to i i x kw PM Genertator, -axis Inuctance 6 Saturation ue to i pm Saturation ue to i i i Figure 5: Generator experimentally extracte -axis flux linkage an -axis inuctance. 125 kw PM Genertator, -axis flux linkage Figure 7: Motor experimentally extracte -axis flux linkage an -axis inuctance kw PM Motor, -axis flux linkage Saturation ue to i x kw PM Genertator, -axis Inuctance 8 Saturation ue to i Saturation ue to i kw PM Motor, -axis Inuctance Saturation ue to i Figure 6: Generator experimentally extracte -axis flux linkage an -axis inuctance Figure 8: Motor experimentally extracte -axis flux linkage an -axis inuctance. UNCLASSIFIED Page of 9
7 Inuctance (H Inuctance (H Proceeings of the 2013 Groun Vehicle Systems Engineering an Technology Symposium (GVSETS Both machines were also characterize through Finite Element Analysis (FEA. FEA is an excellent tool to etermine the basic operating characteristic of a PMSM. It is capable of incluing both self- an cross-saturation effects. However, the inclusion of cross-saturation effects with FEA reuires lengthy calculation time an a transient-magnetic simulation. Figure 9 an 10 show the axis inuctances for each machine, etermine using a FEA Magneto-static simulation scenario. This type of simulation was use, since it is consierably less time consuming than a full transientmagnetic simulation. These inuctances fit within the experimental inuctances shown in Figures Current(A Figure 9: Generator Finite Element Analysis - an -axis inuctance Generator Inuctances Motor Inuctances L L L L Current (A Figure 10: Motor Finite Element Analysis - an -axis inuctance. PROPOSED PARAMETER APPROXIMATION In orer to evelop a high performance controller, accurate knowlege of the parameters is reuire across the entire operating range. Look Up Tables (LUTs are commonly use to evelop controllers base on real parameters. By using a controller base on a LUT, it is possible to fully inclue the non-ieal parameter behavior shown in Figures 5-8 in the motor controller. The main rawback of a LUT is the reuire memory in the controller. The memory space reuirement is irectly proportional to the resolution of the LUT, [1]. In many applications, Digital Signal Processors (DSPs are use to implement the controller. These DSPs are commercially fabricate with a limite memory capacity. A LUT can be implemente in a DSP controller; however, the LUT resolution must be reuce to fit it in the available memory. This can lea to a ecrease in performance of the controller, as information is remove from the table s entries. An accurate curve-fit metho to approximate the real parameters of the motor an generator is propose in this paper. The metho is a ynamic piecewise linear approximation that inclues the parameters non-ieal characteristics, i.e., the cross-saturation effect. It can perform as well as a full parametric LUT controller, but it will not overstress the DSP/microcontroller memory, nor consume much computation time. For the case of, the true inuctance, shown in Figures 5 an 7, is ivie into two linear sectors, as shown in Figure 11. The first step is to etermine the baseline - axis inuctance from the experimental ata, given by (13. L ( i, i L ( i,0 i 0 (13 The two linear approximations for (13 are highlighte in Figure 11 by the line with stars markers. Finally, the cross saturation for this case is ae by subtracting from this baseline approximation, as the other axis current increases. It is assume that cross-saturation in the -axis increases linearly with the -axis current. The incremental function is efine as. By using the experimental ata an inspection, it is etermine that the function representing the cross-saturation terms is as shown in (1. Finally, the total inuctance in these two sectors is given by euation (15. L x 10-3 Sector 2 L incluing Saturation an Cross-Saturation L ( i Figure 11: Motor -axis inuctance piecewise linear approximation, incluing cross saturation. ( sec1&2 L i ( i i (1 i rate sec1&1 (, ( ( sector 1 L i i L i i (15 UNCLASSIFIED Page 5 of 9
8 Proceeings of the 2013 Groun Vehicle Systems Engineering an Technology Symposium (GVSETS In Figure 11, the two sector linear approximation an the true experimental inuctances are plotte together to illustrate the approximation usefulness. The -axis inuctance reuires more linear sectors, as shown in Figures 6 an 8, since it suffers higher saturation than the -axis uantities. Instea of two sectors to approximate this inuctance, four sectors are use as shown in Figure 12. The linear approximations mae in each sector are iscusse from right to left, beginning with sector. As shown in Figures 6 an 8, the effect from the -axis current is minimal in this sector. Therefore, the inuctance approximation is mae by fining the linear euation that intersects points an. L 1_upper 1_lower 2_lower Cross-saturation 2_upper 3_upper Sector 3 Cross-saturation Sector 1 Sector 2 3_lower x 2 x 3 Sector Cross-saturation x 5 Figure 12: -axis inuctance piecewise linear approximation, incluing cross saturation in four sectors. In sector 3, the cross-saturation effects are ae by introucing a ynamic slope change. In this sector, is a fixe point, but the slope of the baseline inuctance is ajuste as a linear function of, given by. The expressions to etermine the -axis inuctance in sector 3 are given by (16-(18. m( i i x x x x 3_ lower 3_ upper 3_ upper i _ rate ( 3 3 sec.3 3_ upper 3_ lower ( i i 3_ upper irate (16 (17 sec.3 L ( i, i m( i ( i x3 ( i (18 sec.3 In sectors 2 an 1, the linear approximation is mae using the same techniue use for the -axis inuctance, where the slope is constant an the cross-saturation is moele by the linear function. Note that all values of are known from the experimental ata. The complete approximation for the motor -axis inuctance along with the true experimental values are shown in Figure 13. The inuctance approximations for the generator were etermine using the same techniue an the results are similar to those of the motor. L Figure 13: Motor -axis inuctance piecewise linear approximation on top of the experimental -axis inuctance. CONTROLLER PERFORMANCE EVALUATION To evaluate the accuracy of the propose parameter approximation metho, a performance simulation base on experimental ata was evelope for each PMSM. The simulation was performe with four ifferent controllers as shown in Figure 1. For this stuy, only the copper losses were consiere. This leas to high efficiency results, but it serves as a proof of concept. Torue reuest Spee L incluing Saturation an Cross-Saturation Motor Controller Base on: 1. Detaile Parameters 2. Parameters w/o cross saturation 3. Propose Metho. FEA base parameters i, i * * i pm Motor Moel Base on Experimental Data Torue, Losses Figure 1: Simulation base on motor experimental ata. First, a highly etaile controller was evelope using a LUT. This controller contains all the saturation effects of the motor. Therefore, this controller is use as the baseline. The tables resolution has steps of 2.5A from zero to 250A. For each current step there is a table entry that matches a torue comman an a spee to a set of an. The secon controller was evelope using experimental ata, but the cross-saturation effects were ignore. For this case the table s resolution is the same as the first case. The thir controller is evelope using the propose parameter approximation metho. Finally, a controller base on FEA was evelope to compare with the experimental UNCLASSIFIED Page 6 of 9
9 Power Copper Losses Power Copper Losses Power Copper Losses Power Copper Losses Proceeings of the 2013 Groun Vehicle Systems Engineering an Technology Symposium (GVSETS parameters. The controllers evelope using the propose an FEA parameters are base on curve fit methos. Each controller was teste in the MTPA an fielweakening regions. For each region, the torue comman was varie from 200 Nm to maximum, an the power copper losses an torue for each operating point was calculate. The results for the performance simulation are shown in Figures w cross-sat (LUT Losses as a function of loaing w/o cross-sat (LUT w propose a Power losses at rate conitions Losses as a function of loaing w cross-sat (LUT w/o cross-sat (LUT w propose b Power losses at 3000RPM, fiel weakening Figure 15: Generator (consiering copper losses only, at a rate conitions, an b a eep fiel weakening operation point. put Generator Torue Performance put Generator Torue Performance 320 w cross-sat (LUT w/o cross-sat 300 w propose T 280 out a Rate Conitions b 3000 RPM case Figure 16: Generator torue (consiering copper losses only, at a rate conitions, an b a eep fiel weakening operation point Figures 15 an 16 show the performance simulation for the generator. For both operating regions, the controller that performe almost as well as the baseline high resolution LUT controller was the controller esigne with the propose parameter approximation metho. This statement is base on the lower power losses an the torue tracking effectiveness. Figure 15 shows that minimum power losses were achieve with the base line controller an the controller using the propose parameters approximation techniue. On the other han, the controllers esigne using FEA parameters an the parameters ignoring cross-saturation are the controllers that yiele the highest power losses. Similar behavior was note for the torue performance shown in Figure 16 where the controller esigne using the propose parameters follows the etaile LUT controller torue performance Losses as a function of loaing w cross-sat (LUT w/o cross-sat (LUT w propose a Power losses at rate conitions Losses as a function of loaing w cross-sat (LUT w/o cross-sat (LUT w propose b Power losses at 3000RPM, fiel weakening Figure 17: Motor (consiering copper losses only, at a rate conitions, an b a eep fiel weakening operation point. The motor exhibite similar behavior as shown in Figures 17 an 18. However, power losses are higher for the motor because it experiences more cross-saturation than the generator. For the motor, the controller esigne using the propose parameter approximation metho ha the closest performance to the etaile LUT controller. UNCLASSIFIED Page 7 of 9
10 Proceeings of the 2013 Groun Vehicle Systems Engineering an Technology Symposium (GVSETS put Motor Torue Performance put Motor Torue Performance 320 w cross-sat (LUT 300 w/o cross-sat w propose a Rate Conitions b 3000 RPM case Figure 18: Motor torue (consiering copper losses only, at a rate conitions, an b a eep fiel weakening operation point. CONCLUSIONS In this paper, the effects of iron saturation on the performance of a motor rive are stuie using two PMSMs. The flux linkages an inuctances of each machine were etermine through a characterization process an are shown in Figures 5-8. Saturation is evient from these figures an cannot be ignore or assume negligible. It is possible to obtain the parameters reuire to esign a motor controller through FEA simulations or experimental ata collection. The inclusion of cross-saturation effects in the controller evelopment is vital to ensure a high performance, high efficiency controller. A metho to inclue these effects is propose. It was teste against controllers base on high resolution LUT, LUT without cross-saturation, an FEA parameters. Figures emonstrate the valiity of the metho. The simulations showe that the propose metho has low an goo torue performance; both metrics are comparable to the performance of the high resolution LUT controller at both low an high spees. Compare with conventional approaches, the propose metho applie to a 125kW machine contribute to a reuction in copper losses as high as 900W, resulting in an efficiency gain of 1.36%. The propose controller, incorporating a ynamic piecewise linear approximation of the machine flux linkages, is realizable in the majority of motor control DSPs use in high performance PMSM controllers ue to its computational efficiency. The controller helps to improve the ynamic response of the rive an its improve efficiency contributes to a ecrease thermal buren on the cooling system in military groun vehicle applications. REFERENCES [1] Khalil, G., "Challenges of hybri electric vehicles for military applications," Vehicle Power an Propulsion Conference, VPPC '09. IEEE, vol., no., pp.1,3, 7-10 Sept [2] Yuan Cheng; Trigui, R.; Espanet, C.; Bouscayrol, A.; Shumei Cui, "Specifications an Design of a PM Electric Variable Transmission for Toyota Prius II," Vehicular Technology, IEEE Transactions on, vol.60, no.9, pp.106,11, Nov [3] Estima, J.O.; Marues Caroso, A.J., "Efficiency Analysis of Drive Train Topologies Applie to Electric/Hybri Vehicles," Vehicular Technology, IEEE Transactions on, vol.61, no.3, pp.1021,1031, March 2012 [] Seok-Myeong Jang; Seon-Ik Hwang; Kyoung-Jin Ko; Jang-Young Choi; So-Young Sung, "Driving performance evaluation of interior permanent magnet (IPM motor using circuit parameter estimation," Electrical Machines an Systems (ICEMS, 2010 International Conference on, vol., no., pp.1205,1208, Oct [5] Fajkus, P.; Klima, B.; Hutak, P., "High spee range fiel oriente control for permanent magnet synchronous motor," Power Electronics, Electrical Drives, Automation an Motion (SPEEDAM, 2012 International Symposium on, vol., no., pp.225,230, June 2012 [6] J. G. Cintron-Rivera, A. S. Babel, E. E. Montalvo-Ortiz, S. N. Foster an E. G. Strangas, A Simplifie Characterization Metho Incluing Saturation Effects for Permanent Magnet Machines, 2012 International Conference on Electrical Machines (ICEM, pp , [7] Babel, A.S.; Foster, S.N.; Cintron-Rivera, J.G.; Strangas, E.G., "Parametric sensitivity in the analysis an control of permanent magnet synchronous machines," Electrical Machines (ICEM, 2012 XXth International Conference on, vol., no., pp.103,100, 2-5 Sept [8] S. Kim, Y. Yoon, S. Sul, K. Ie, "Maximum Torue per Ampere (MTPA Control of an IPM Machine Base on Signal Injection Consiering Inuctance Saturation," Power Electronics, IEEE Transactions on, vol.28, no.1, pp.88,97, Jan [9] Y. Nanfang, L. Guangzhao, L. Weiguo an W. Kang, Interior Permanent Magnet Synchronous Motor Control for Electric Vehicle Using Look-up Table, 2012 IEEE 7 th International Power Electronics an UNCLASSIFIED Page 8 of 9
11 Proceeings of the 2013 Groun Vehicle Systems Engineering an Technology Symposium (GVSETS Motion Control Conference, vol. 2, pp , June 2-5, [10] T. Herol, D. Franck, E. Lange an K. Hameyer, Extension of a - Moel of a Permanent Magnet Excite Synchronous Machine by incluing Saturation, Cross-Coupling an Slotting Effects, 2011 IEEE International Electric Machines an Drives Conference (IEMDC, pp , May [11] Seok-Myeong Jang; Seon-Ik Hwang; Kyoung-Jin Ko; Jang-Young Choi; So-Young Sung, "Driving performance evaluation of interior permanent magnet (IPM motor using circuit parameter estimation,"electrical Machines an Systems (ICEMS, 2010 International Conference on, vol., no., pp.1205,1208, Oct [12] S. Kim, Y. Yoon, S. Sul, K. Ie, "Maximum Torue per Ampere (MTPA Control of an IPM Machine Base on Signal Injection Consiering Inuctance Saturation," Power Electronics, IEEE Transactions on, vol.28, no.1, pp.88,97, Jan [13] Z. Li, H. Li, "MTPA control of PMSM system consiering saturation an cross-coupling," Electrical Machines an Systems (ICEMS, th International Conference on, vol., no., pp.1,5, 21-2 Oct [1] J.G. Cintron-Rivera, S.N.. Foster, C.E. Nino-Baron an Elias G. Strangas, High Performance Controllers for Interior Permanent Magnet Synchronous Machines Using Look-up Tables an Curve-fitting Methos, IEMDC 2013 Ohare, Illinois. UNCLASSIFIED Page 9 of 9
HIGH PERFORMANCE CONTROLLERS BASED ON REAL PARAMETERS TO ACCOUNT FOR PARAMETER VARIATIONS DUE TO IRON SATURATION
213 NDIA GROUND VEHICLE SYSTEMS ENGINEERING AND TECHNOLOGY SYMPOSIUM VEHICLE ELECTRONICS AND ARCHITECTURE (VEA MINI-SYMPOSIUM AUGUST 21-22, 213 - TROY, MICHIGAN HIGH PERFORMANCE CONTROLLERS BASED ON REAL
More informationON-LINE PARAMETER ESTIMATION AND ADAPTIVE CONTROL OF PERMANENT MAGNET SYNCHRONOUS MACHINES. A Dissertation. Presented to
ON-LINE PARAMETER ESTIMATION AND ADAPTIVE CONTROL OF PERMANENT MAGNET SYNCHRONOUS MACHINES A Dissertation Presente to The Grauate Faculty of the University of Akron In Partial Fulfillment Of the Reuirements
More informationDouble Closed-loop Control System Design of PMSM Based on DSP MoupengTao1, a,songjianguo2, b, SongQiang3, c
4th International Conference on Mechatronics, Materials, Chemistry an Computer Engineering (ICMMCCE 2015) Double Close-loop Control System Design of PMSM Base on DSP MoupengTao1, a,songjianguo2, b, SongQiang3,
More informationVector Control of Permanent Magnet Synchronous Motor for Fan of New Energy Vehicle
Vector Control of Permanent Magnet Synchronous Motor for Fan of New Energy Vehicle Liu Yong* Yancheng Teachers University, school of mathematics an statistics, China Abstract:In this paper, base on the
More informationSILICON CARBIDE FOR NEXT GENERATION VEHICULAR POWER CONVERTERS. John Kajs SAIC August UNCLASSIFIED: Dist A. Approved for public release
SILICON CARBIDE FOR NEXT GENERATION VEHICULAR POWER CONVERTERS John Kajs SAIC 18 12 August 2010 Report Documentation Page Form Approved OMB No. 0704-0188 Public reporting burden for the collection of information
More informationModel Reference Adaptive Fuzzy Controller for Permanent Magnet Synchronous Motor
Volume 50, Number 1, 2009 25 Moel Reference Aaptive Fuzzy Controller for Permanent Magnet Synchronous Motor A. MEROUFEL, M. MASSOUM an B. BELABBES Abstract: Conventional control epens on the mathematical
More informationUniversities of Leeds, Sheffield and York
promoting access to White Rose research papers Universities of Lees, Sheffiel an York http://eprints.whiterose.ac.uk/ White Rose Research Online URL for this paper: http://eprints.whiterose.ac.uk/4495/
More informationInvestigating Converter Options for Automotive Grade Permanent Magnet Sychronous Generators
Investigating Converter Options for Automotive Grae Permanent Magnet Sychronous Generators Erkan MESE *, Yusuf YAŞA *, Hakan AKÇA *, Mustafa G. AYDENIZ *, Murat AYAZ **, Murat TEZCAN * ( * )Yiliz Technical
More informationHIGH TEMPERATURE (250 C) SIC POWER MODULE FOR MILITARY HYBRID ELECTRICAL VEHICLE APPLICATIONS
HIGH TEMPERATURE (250 C) SIC POWER MODULE FOR MILITARY HYBRID ELECTRICAL VEHICLE APPLICATIONS R. M. Schupbach, B. McPherson, T. McNutt, A. B. Lostetter John P. Kajs, and Scott G Castagno 29 July 2011 :
More informationConstruction of Power Efficient Routing Tree for Ad Hoc Wireless Networks using Directional Antenna
Construction of Power Efficient Routing Tree for A Hoc Wireless Networks using Directional Antenna Qing Dai an Jie Wu Department of Computer Science an Engineering Floria Atlantic University Boca Raton,
More informationDETERMINATION OF OPTIMAL DIRECT LOAD CONTROL STRATEGY USING LINEAR PROGRAMMING
DETERMINATION OF OPTIMAL DIRECT LOAD CONTROL STRATEGY USING LINEAR PROGRAMMING Zelko Popovic Distribution engineer Rae Koncara 57, 24300 Backa Topola, Yugoslavia Phone: +38 24 74 220 Fax: +38 24 74 898
More informationUniversity of Sidi Mohammed Ben Abdellah Fez, Morocco
Matlab & Simulink Simulation with FPGA-Base Implementation Sliing Moe Control of a Permanent Magnet Synchronous Machine Drive BADRE BOSSOUFI (Stuent Member IEEE) 1)2), MOHAMMED KARIM 1), SILVIU IONIłĂ
More information2013 Texas Instruments Motor Control Training Series. -V th. InstaSPIN Training
2013 Texas Instruments Motor Control Training Series -V th InstaSPIN Training How Do You Control Torque on a DC Motor? Brush DC Motor Desire Current + - Error Signal PI Controller PWM Power Stage Texas
More informationPrincipal Component Analysis-Based Compensation for Measurement Errors Due to Mechanical Misalignments in PCB Testing
Principal Component Analysis-Base Compensation for Measurement Errors Due to Mechanical Misalignments in PCB Testing Xin He 1, Yashwant Malaiya 2, Anura P. Jayasumana 1 Kenneth P. Parker 3 an Stephen Hir
More informationANTENNA DEVELOPMENT FOR MULTIFUNCTIONAL ARMOR APPLICATIONS USING EMBEDDED SPIN-TORQUE NANO-OSCILLATOR (STNO) AS A MICROWAVE DETECTOR
ANTENNA DEVELOPMENT FOR MULTIFUNCTIONAL ARMOR APPLICATIONS USING EMBEDDED SPIN-TORQUE NANO-OSCILLATOR (STNO) AS A MICROWAVE DETECTOR Report Documentation Page Form Approved OMB No. 0704-0188 Public reporting
More informationPERFORMANCE OF FUZZY LOGIC BASED MICROTURBINE GENERATION SYSTEM CONNECTED TO GRID/ISLANDED MODE
International Journal of Fuzzy Logic Systems (IJFLS) Vol.2, No.3, July 22 PERFORMANCE OF FUZZY LOGIC BASED MICROTURBINE GENERATION SYSTEM CONNECTED TO GRID/ISLANDED MODE Sanjeev K Nayak an D N Gaonkar
More informationDavid Siegel Masters Student University of Cincinnati. IAB 17, May 5 7, 2009 Ford & UM
Alternator Health Monitoring For Vehicle Applications David Siegel Masters Student University of Cincinnati Report Documentation Page Form Approved OMB No. 0704-0188 Public reporting burden for the collection
More informationWireless Event-driven Networked Predictive Control Over Internet
UKACC International Conference on Control 22 Cariff, UK, 3-5 September 22 Wireless Event-riven Networke Preictive Control Over Internet Wenshan Hu, Hong Zhou, an Qijun Deng Abstract In networke control
More informationMaximum Torque-per-Amp Control for Traction IM Drives: Theory and Experimental Results
Maimum Torue-per-Amp Control for Traction IM Drives: Theory an Eperimental Results Serhiy Bozhko, Serhii Dymko, Serhii Kovbasa, Sergei Peresaa, Faculty of Engineering, University of Nottingham, University
More informationSuppression of Short-circuit Current in Halt Sequence to StopTwo-level Inverter connected to PMSM during Regeneration Mode
Suppression of Short-circuit Current in Halt Seuence to StopTwo-level Inverter connecte to PMSM uring Regeneration Moe Tsuyoshi Nagano an Jun-ichi Itoh Dept. of Electrical Engineering Nagaoka University
More informationUNIT IV CONTROLLER TUNING:
UNIT IV CONTROLLER TUNING: Evaluation Criteria IAE, ISE, ITAE An ¼ Decay Ratio - Tuning:- Process Reaction Curve Metho, Continuous Cycling Metho An Dampe Oscillation Metho Determination Of Optimum Settings
More informationMeasurement of Semi-Anechoic Chamber Using Modified VSWR method above 1GHz
Measurement of Semi-Anechoic Chamber Using Moifie VSWR metho above 1GHz M. Bittera, K. Kováč, J. Hallon Department of Measurement, Faculty of Electrical Engineering an Information Technology, Slovak University
More informationRCGA based PID controller with feedforward control for a heat exchanger system
Journal of the Korean Society of Marine Engineering, Vol. 1, No. pp. 11~17, 17 ISSN 223-7925 (Print) J. Korean Soc. of Marine Engineering (JKOSME) ISSN 223-8352 (Online) https://oi.org/.5916/jkosme.17.1..11
More informationSECONDARY TRANSMISSION POWER OF COGNITIVE RADIOS FOR DYNAMIC SPECTRUM ACCESS
SECONDARY TRANSMISSION POWER OF COGNITIVE RADIOS FOR DYNAMIC SPECTRUM ACCESS Xiaohua Li 1 1 Department of ECE State University of New York at Binghamton Binghamton, NY 139, USA {xli,jhwu1}@binghamton.eu
More informationThe Analysis and Complementarity of Abbe Principle Application Limited in Coordinate Measurement
Proceeings of the Worl Congress on Engineering 00 Vol III The Analysis an Complementarity of Abbe Principle Application Limite in Coorinate Measurement Fei Yetai, Shang Ping, Chen Xiaohuai, Huang Qiangxian
More informationThe estimation of PID controller parameters of vector controlled induction motor using Ziegler-Nichols method
Journal of Engineering Research an Applie Science Available at www.journaleras.com Volume 4(1), June 2015, pp 278-282 ISSN 2147-471 2015 The estimation of PID controller parameters of vector controlle
More informationController Design for Cuk Converter Using Model Order Reduction
n International Conference on Power, Control an Embee Systems Controller Design for Cuk Converter Using Moel Orer Reuction Brijesh Kumar Kushwaha an Mr. Aniruha Narain Abstract: Cuk converter contain two
More informationApplication of Vector Fitting to High Frequency Transformer Modeling
Application of Vector Fitting to High Frequenc Transformer Moeling Bjørn Gustavsen SINTEF Energ Research, N-76 Tronheim, Norwa (e-mail: bjorn.gustavsen@sintef.no) Abstract This paper escribes a proceure
More informationBidirectional step-up/step-down DC-DC converter with magnetically coupled coils
Biirectional step-up/step-own DC-DC converter with magnetically couple coils Frivalský M.*, Dobrucký B.*, Scelba G.**, Špánik P.*, Drgoňa P.* * University of Zilina, Department of Mechatronics an electronics,
More informationChapter 2 Review of the PWM Control Circuits for Power Converters
Chapter 2 Review of the PWM Control Circuits for Power Converters 2. Voltage-Moe Control Circuit for Power Converters Power converters are electrical control circuits that transfer energy from a DC voltage
More informationImproving the Near-Metal Performance of UHF RFID Tags
Improving the Near-Metal Performance of UHF RFID Tags Daniel D. Deavours Information an Telecommunications Technology Center University of Kansas, Lawrence, KS Email: eavours@ittc.ku.eu Abstract It is
More informationKEY FEATURES TEST CAPABILITIES 8000S HIGH POWER EARTH TESTING SYSTEM STANDARDS COMPLIANCE
KEY FEATURES 8000S HIGH POWER EARTH TESTING SYSTEM High power earth systems (Substations, Transmission towers, etc) have to be perioically monitore to check if they comply with safety levels establishe
More informationJoint Cooperative Relaying and Jamming for Maximum Secrecy Capacity in Wireless Networks
Joint Cooperative Relaying an Jamming for Maximum Secrecy Capacity in Wireless Networks Li Wang, Chunyan Cao, Mei Song an Yu Cheng Beijing Key Laboratory of Work Safety Intelligent Monitoring School of
More informationSignal Processing Architectures for Ultra-Wideband Wide-Angle Synthetic Aperture Radar Applications
Signal Processing Architectures for Ultra-Wideband Wide-Angle Synthetic Aperture Radar Applications Atindra Mitra Joe Germann John Nehrbass AFRL/SNRR SKY Computers ASC/HPC High Performance Embedded Computing
More informationThis is an electronic reprint of the original article. This reprint may differ from the original in pagination and typographic detail.
Powere by TCPDF (www.tcpf.org) This is an electronic reprint of the original article. This reprint may iffer from the original in pagination an typographic etail. Piippo, Antti; Hinkkanen, Marko; Luomi,
More informationTaylor, Muthiah, Kulakowski, Mahoney and Porter 1 AN ARTIFICIAL NEURAL NETWORK SPEED PROFILE MODEL FOR HIGH- SPEED HIGHWAY CONSTRUCTION WORK ZONES
Taylor, Muthiah, Kulakowski, Mahoney an Porter 1 AN ARTIFICIAL NEURAL NETWORK SPEED PROFILE MODEL FOR HIGH- SPEED HIGHWAY CONSTRUCTION WORK ZONES Submission Date: August 1, 2005 Wor Count: 57 wors DOUGLAS
More informationDynamic Hybrid Duplex for Rate Maximization in OFDMA. Sangmin Oh and Chae Y. Lee
Dynamic Hybri Duplex for Rate Maximization in OFDMA Sangmin Oh an Chae Y. Lee Dept. of Inustrial Engineering, KAIST, 373-1 Kusung Dong, Taeon, Korea Tel: +82-42-350-5916, FAX: +82-42-350-3110 Email: {sangmin.oh,
More informationRelay Deployment and Power Control for Lifetime Elongation in Sensor Networks
Relay Deployment an Power Control for Lifetime Elongation in Sensor Networks Yufeng Xin, Tuna Güven, Mark Shayman Institute of Avance Computer Stuies University of Marylan, College Park, MD 074 e-mail:
More informationValidation of a Non-Line-of-Sight Path-Loss Model for V2V Communications at Street Intersections
Valiation of a Non-Line-of-Sight Path-Loss Moel for V2V Communications at Street Intersections Taimoor Abbas, Anreas Thiel, Thomas Zemen, Christoph F. Mecklenbräuker, an Frerik Tufvesson Department of
More informationInvestigation of a Forward Looking Conformal Broadband Antenna for Airborne Wide Area Surveillance
Investigation of a Forward Looking Conformal Broadband Antenna for Airborne Wide Area Surveillance Hany E. Yacoub Department Of Electrical Engineering & Computer Science 121 Link Hall, Syracuse University,
More informationPage 1. Overview : Wireless Networks Lecture 7: Cellular Networks. The advent of cellular networks. The cellular network design.
Overview 18-759: Wireless Networks Lecture 7: Cellular Networks Dina Papagiannaki & Peter Steenkiste Departments of Computer Science an Electrical an Computer Engineering Spring Semester 2009 http://www.cs.cmu.eu/~prs/wireless09/
More informationModeling, Simulation and Development of Supervision/Control System for Hybrid Wind Diesel System Supplying an Isolated Load
Moeling, Simulation an Development of Supervision/Control System for Hybri Win Diesel System Supplying an Isolate Loa Vigneshwaran Rajasekaran 1, Ael Merabet 1 an Hussein Ibrahim 2 1 Division of Engineering,
More informationSpace-Vector PWM Inverter Feeding a Permanent-Magnet Synchronous Motor
Worl Acaey of Science, Engineering an echnology International Journal of Electrical, Coputer, Energetic, Electronic an Counication Engineering ol:4, No:5, 00 Space-ector PWM Inverter Feeing a Peranent-Magnet
More informationWave-Induced Fluctuations in Underwater Light Field: Analysis of Data from RaDyO Experiments
DISTRIBUTION STATEMENT A. Approve for public release; istribution is unlimite. Wave-Inuce Fluctuations in Unerwater Light Fiel: Analysis of Data from RaDyO Experiments Dariusz Stramski Marine Physical
More informationThe 5th International Power Engineering and Optimization Conference (PEOCO2011), Shah Alam, Selangor, Malaysia : 6-7 June 2011
The 5th International Power Engineering an Optimization onference (PEOO211), Shah Alam, Selangor, Malaysia : 6-7 June 211 Moeling an Simulation of Umlazi suburb of Durban Municipality Network (South Africa)
More informationDownward Trimming of Polymer Thick Film Resistors through High Voltage Pulses
Downwar Trimming of Polymer Thick Film Resistors through High Voltage Pulses Y.Srinivasa Rao E.C.E. Department Shri Vishnu Engineering College For Women Vishnupur, Bhimavaram-540 W.G.Dt.,Ap, Inia Phone
More informationU.S. Army Training and Doctrine Command (TRADOC) Virtual World Project
U.S. Army Research, Development and Engineering Command U.S. Army Training and Doctrine Command (TRADOC) Virtual World Project Advanced Distributed Learning Co-Laboratory ImplementationFest 2010 12 August
More informationDingwen Yu and Jiasheng Zhang
INTERNATIONAL JOURNAL OF INFORMATION AND SYSTEMS SIENES Volumer, Numver 3, ages 384-397 6 Institute for Scientific omputing an Information RESEARH OF ID ONTROLLER AND FUZZY ID ONTROLLER Dingwen Yu an Jiasheng
More informationField Visualization by Image Processing
The 0th International Symposium on Flow Visualiation August 6-9, 00, Kyoto, Japan F008 Fiel Visualiation by Image Processing Image refining an fiel characteristics arinova, I. *, Eno, H. *, Hayano, S.
More informationDynamic Wireless Power Transfer System for Electric Vehicles to Simplify Ground Facilities - Real-time Power Control and Efficiency Maximization -
Worl Electric Vehicle Journal Vol. 8 - ISSN 232-6653 - 26 WEVA Page WEVJ8-5 EVS29 Symposium Montréal, Québec, Canaa, June 9-22, 26 Dynamic Wireless Power Transfer System for Electric Vehicles to Simplify
More informationExperiences Linking Vehicle Motion Simulators to Distributed Simulation Experiments
Experiences Linking Vehicle Motion Simulators to Distributed Simulation Experiments Richard W. Jacobson Electrical Engineer 1/ 18 Report Documentation Page Form Approved OMB No. 0704-0188 Public reporting
More informationDavid L. Lockwood. Ralph I. McNall Jr., Richard F. Whitbeck Thermal Technology Laboratory, Inc., Buffalo, N.Y.
ANALYSIS OF POWER TRANSFORMERS UNDER TRANSIENT CONDITIONS hy David L. Lockwood. Ralph I. McNall Jr., Richard F. Whitbeck Thermal Technology Laboratory, Inc., Buffalo, N.Y. ABSTRACT Low specific weight
More informationCode-Carrier Divergence Monitoring for the GPS Local Area Augmentation System
Coe-Carrier Divergence Monitoring for the GPS Local Area Augmentation System Dwaraanath V. Simili an Boris Pervan, Illinois Institute of Technology, Chicago, IL Abstract Coe-carrier smoothing is a commonly
More information2 Dept. of Electrical and Electronic Engineering ( ) = d
Close-Loop Control Design for a Three-Level Three-Phase Neutral-Point-Clampe Inverter Using the Optimize Nearest-Three Virtual-Space-Vector Moulation S. Busquets-Monge 1, J. D. Ortega 1, J. Boronau 1,
More informationOn the Real Time Implementation of a Controller for an Electromechanical System
On the Real Time Implementation of a Controller for an Electromechanical System Ruben Salas-Cabrera, Jonathan C. Mayo-Malonao, Erika Y. Renon-Fraga, Euaro N. Salas-Cabrera an Aaron Gonzalez-Roriguez Abstract
More informationUsing Chaos to Detect IIR and FIR Filters
PIERS ONLINE, VOL. 6, NO., 00 90 Using Chaos to Detect IIR an FIR Filters T. L. Carroll US Naval Research Lab, Coe 66, Washington, DC 07, USA Abstract In many signal processing applications, IIR an FIR
More informationImprovement of Power Factor and Harmonic Reduction with VSC for HVDC System
International Journal of Engineering an Management Research, Volume-3, Issue-2, April 2013 ISSN No.: 2250-0758 Pages: 6-12 www.ijemr.net Improvement of Power Factor an Harmonic Reuction with VSC for HVDC
More informationEnergy Efficient Virtual MIMO-based Cooperative Communications for Wireless Sensor Networks
Energy Efficient Virtual MIMO-base Cooperative Communications for Wireless Sensor Networks Suharman K. Jayaweera Department of Electrical an Computer Engineering Wichita State University, Wichita, KS,
More informationStrategic Technical Baselines for UK Nuclear Clean-up Programmes. Presented by Brian Ensor Strategy and Engineering Manager NDA
Strategic Technical Baselines for UK Nuclear Clean-up Programmes Presented by Brian Ensor Strategy and Engineering Manager NDA Report Documentation Page Form Approved OMB No. 0704-0188 Public reporting
More informationAN-1140 APPLICATION NOTE
APPLICATION NOTE One Technology Way P.O. Box 9106 Norwoo, MA 02062-9106, U.S.A. Tel: 781.329.4700 Fax: 781.461.3113 www.analog.com Microphone Array Beamforming by Jera Lewis INTRODUCTION All MEMS microphones
More informationNoise Tolerance of Improved Max-min Scanning Method for Phase Determination
Noise Tolerance of Improved Max-min Scanning Method for Phase Determination Xu Ding Research Assistant Mechanical Engineering Dept., Michigan State University, East Lansing, MI, 48824, USA Gary L. Cloud,
More informationWind sculpture. Cable 2. Cable 1. Sculpture
Win sculpture Your frien, an artist, has been thinking about an interesting way to isplay a new win sculpture she has just create. In orer to create an aural as well as visual effect, she woul like to
More information2.35 Tuning PID Controllers
2.35 Tuning PID Controllers P. W. MURRILL (1970) P. D. SCHNELLE, JR. (1985) B. G. LIPTÁK (1995) J. GERRY, M. RUEL, F. G. SHINSKEY (2005) In orer for the reaer to fully unerstan the content an concepts
More informationTesting, Characterization, and Modeling of SiC Diodes for Transportation Applications
Testing, haracterization, an Moeling of ioes for Transportation Applications Burak Ozpineci 1,3 burak@ieee.org Leon M. Tolbert 1,2 tolbert@utk.eu Sye K. slam 1 sislam@utk.eu Fang Z. Peng 2,4 fzpeng@msu.eu
More informationDECENTRALIZED CIVIL STRUCTURAL CONTROL USING A REAL-TIME WIRELESS SENSING AND CONTROL SYSTEM
4 th Worl Conference on Structural Control an Monitoring 4WCSCM-252 DECENTRALIZED CIVIL STRUCTURAL CONTROL USIN A REAL-TIME WIRELESS SENSIN AND CONTROL SYSTEM Abstract Y. Wang 1, R. A. Swartz 2, J. P.
More informationUniversity of Huddersfield Repository
University of Huersfiel Repository Towsyfyan, Hossein, Hassin, Osama, Gu, Fengshou an Ball, Anrew Characterization of Acoustic Emissions from Mechanical Seals for Fault Detection Original Citation Towsyfyan,
More informationDescribing Function Analysis of the Voltage Source Resonant Inverter with Pulse Amplitude Modulation
Volume 48, Number 3, 007 3 Describing Function Analysis of the Voltage Source Resonant nverter with Pulse Amplitue Moulation Anrás KELEMEN, Nimró KUTAS Abstract: Pulse amplitue moulation (PAM is a wiely
More informationResource Allocation for Cooperative Transmission in Wireless Networks with Orthogonal Users
Resource Allocation for Cooperative Transmission in Wireless Networks with Orthogonal Users D. Richar Brown III Electrical an Computer Engineering Department Worcester Polytechnic Institute Worcester,
More informationCross-layer Routing Optimization for Wireless Networks with Cooperative Diversity
Cross-layer Routing Optimiation for Wireless Networs with Cooperative Diversity Zhiguo Ding an Kin K. Leung Department of Electrical an Electronic Engineering Imperial College Lonon, UK. Email: {higuo.ing,
More informationStudent Independent Research Project : Evaluation of Thermal Voltage Converters Low-Frequency Errors
. Session 2259 Student Independent Research Project : Evaluation of Thermal Voltage Converters Low-Frequency Errors Svetlana Avramov-Zamurovic and Roger Ashworth United States Naval Academy Weapons and
More informationLightning Protection Optimization for Large Wind Turbines with Method-of-Moments
Lightning Protection Optimization for Large Win Turbines with Metho-of-Moments Florian Krug, Ralph Teichmann General Electric - Global Research Freisinger Lanstrasse 50, 85748 Munich, GERMAY Ulrich Jakobus,
More informationIndoor Positioning Using Ultrasound and Radio Combination
Inoor Positioning Using Ultrasoun an Raio Combination Gintautas Salcius, Evalas Povilaitis, Algimantas Tacilauskas Centre of Real Time Computer Systems, Kaunas University of Technology Stuentu St. 50,
More informationIN GENERAL, an optical network can consist of a
1 Geometric Capacity Provisioning for Wavelength-Switche WDM Networks Li-Wei Chen, Eytan Moiano Abstract In this paper, we use an asymptotic analysis similar to the sphere-packing argument in the proof
More informationFuzzy Polar Dynamic Voltage Restorer as Voltage Sag Restorer and Active Filter Without Zero Sequence Blocking
Fuzzy Polar Dynamic Voltage Restorer as Voltage Sag Restorer an Active Filter Without Zero Sequence Blocking Margo P, M Hery P, M Ashari, Zaenal P *),Takashi Hiyama **) *) Dept. of Electrical Eng, Sepuluh
More informationSensorless Control of a Novel IPMSM Based on High-Frequency Injection
Sensorless Control of a Novel IPMSM Based on High-Frequency Injection Xiaocan Wang*,Wei Xie**, Ralph Kennel*, Dieter Gerling** Institute for Electrical Drive Systems and Power Electronics,Technical University
More informationPULSED POWER SWITCHING OF 4H-SIC VERTICAL D-MOSFET AND DEVICE CHARACTERIZATION
PULSED POWER SWITCHING OF 4H-SIC VERTICAL D-MOSFET AND DEVICE CHARACTERIZATION Argenis Bilbao, William B. Ray II, James A. Schrock, Kevin Lawson and Stephen B. Bayne Texas Tech University, Electrical and
More informationMusical Wind Instrument Analysis
Musical Win Instrument Analysis Darren, Murray Campbell Department of Acoustics an Flui Dynamics, University of Einburgh, EH9 3JZ, Einburgh, Scotlan D.A.@sms.e.ac.uk,.m.campbell@e.ac.uk The acoustic impeance
More informationPower Efficient Pilot Symbol Power Allocation under Time-variant Channels
Power Efficient Pilot Symbol Power Allocation uner Time-variant Channels Michal Šimko, Paulo S. R. Diniz,QiWang an Markus Rupp Institute of Telecommunications, Vienna University of Technology, Vienna,
More informationLocalization of Phase-to-Phase Faults on a Medium Voltage Feeder with Distributed Generation
Localization of Phase-to-Phase Faults on a Meium Voltage Feeer with Distribute Generation Jorun rene Marvik, Hans Kristian Høialen, Astri Petterteig Abstract This paper presents a localization proceure
More informationAPPLICATION OF OPTIMAL-TUNING PID CONTROL TO INDUSTRIAL HYDRAULIC SYSTEMS. G. P. Liu*, S. Daley + and G. R. Duan
Copyright 2002 IFAC 5th Triennial Worl Congress, Barcelona, Spain APPLICATION OF OPTIMAL-TUNING PID CONTROL TO INDUSTRIAL HYDRAULIC SYSTEMS G. P. Liu*, S. Daley + an G. R. Duan * University of Nottingham
More informationUNCLASSIFIED UNCLASSIFIED 1
UNCLASSIFIED 1 Report Documentation Page Form Approved OMB No. 0704-0188 Public reporting burden for the collection of information is estimated to average 1 hour per response, including the time for reviewing
More informationTHE NATIONAL SHIPBUILDING RESEARCH PROGRAM
SHIP PRODUCTION COMMITTEE FACILITIES AND ENVIRONMENTAL EFFECTS SURFACE PREPARATION AND COATINGS DESIGN/PRODUCTION INTEGRATION HUMAN RESOURCE INNOVATION MARINE INDUSTRY STANDARDS WELDING INDUSTRIAL ENGINEERING
More informationA RENEWED SPIRIT OF DISCOVERY
A RENEWED SPIRIT OF DISCOVERY The President s Vision for U.S. Space Exploration PRESIDENT GEORGE W. BUSH JANUARY 2004 Report Documentation Page Form Approved OMB No. 0704-0188 Public reporting burden for
More informationHybrid Posicast Controller for a DC-DC Buck Converter
SERBIAN JOURNAL OF ELETRIAL ENGINEERING Vol. 5, No. 1, May, 11-13 Hybri Posicast ontroller for a D-D Buck onverter Kaithamalai Uhayakumar 1, Ponnusamy Lakshmi, Kanasamy Boobal Abstract: A new Posicast
More informationIREAP. MURI 2001 Review. John Rodgers, T. M. Firestone,V. L. Granatstein, M. Walter
MURI 2001 Review Experimental Study of EMP Upset Mechanisms in Analog and Digital Circuits John Rodgers, T. M. Firestone,V. L. Granatstein, M. Walter Institute for Research in Electronics and Applied Physics
More informationA NEW PUZZLE FOR ITERATED COMPLETE GRAPHS OF ANY DIMENSION
A NEW PUZZLE FOR ITERATED COMPLETE GRAPHS OF ANY DIMENSION ELIZABETH SKUBAK AND NICHOLAS STEVENSON ADVISOR: PAUL CULL OREGON STATE UNIVERSITY ABSTRACT. The Towers of Hanoi puzzle can be use to label a
More informationAn Observer Design Strategy in Electric Power Steering System
An Observer Design Strategy in Electric Power Steering System Jingying Lu,a, Wei Jiang,b, Tomokazu Abe 2, Yu Fujimura 2, Seiji Hashimoto 2,c an Mitsunobu Kajitani 3, Yangzhou University, Huayang west roa
More informationRCT. RDT Tapping Attachments
RCT. RDT Tapping Attachments Threa prouction on machining centers with constant spee tapping CST Constant Spee Tapping relies on a compact tapping attachment to provie tap reversal. The machine spinle
More informationINTERFERENCE REJECTION PERFORMANCE AS A MEANS OF FREQUENCY OPTIMISATION IN A MIXED CELLULAR/MANET NETWORK
ITERFERECE REJECTIO PERFORMACE A A MEA OF FREQUECY OPTIMIATIO I A MIXED CELLULAR/MAET ETORK Kayonne ebley Faculty Avisor: Dr. Richar Dean Department of Electrical an Computer Engineering Morgan tate University
More informationFrequency Stabilization Using Matched Fabry-Perots as References
April 1991 LIDS-P-2032 Frequency Stabilization Using Matched s as References Peter C. Li and Pierre A. Humblet Massachusetts Institute of Technology Laboratory for Information and Decision Systems Cambridge,
More informationParallel Operation of Permanent Magnet Synchronous Generator Based Windmills Connected to HVDC-VSC Link
Parallel Operation of Permanent Magnet Synchronous Generator Base Winmills Connecte to HVDC-VSC Link R. Vijaya Priya S. Kishore Rey M.P. Selvan P. Raja Hybri Electrical Systems Laboratory Department of
More informationAugust 9, Attached please find the progress report for ONR Contract N C-0230 for the period of January 20, 2015 to April 19, 2015.
August 9, 2015 Dr. Robert Headrick ONR Code: 332 O ce of Naval Research 875 North Randolph Street Arlington, VA 22203-1995 Dear Dr. Headrick, Attached please find the progress report for ONR Contract N00014-14-C-0230
More informationPV Array Emulator for Testing Commercial PV Inverters
http://x.oi.org/10.5755/j01.eee.19.10.5899 ELEKTRONIKA IR ELEKTROTECHNIKA, ISSN 1392-1215, VOL. 19, NO. 10, 2013 PV Array Emulator for Testing Commercial PV Inverters C. Roncero-Clemente 1, E. Romero-Caaval
More informationAn Intelligent 3D User Interface Adapting to User Control Behaviors
An Intelligent 3D User Interface Aapting to User Control Behaviors Tsai-Yen Li Computer Science Department National Chengchi University Taipei, Taiwan 11623, R.O.C. +886 2 2938 7170 li@nccu.eu.tw Shu-Wei
More informationHybrid QR Factorization Algorithm for High Performance Computing Architectures. Peter Vouras Naval Research Laboratory Radar Division
Hybrid QR Factorization Algorithm for High Performance Computing Architectures Peter Vouras Naval Research Laboratory Radar Division 8/1/21 Professor G.G.L. Meyer Johns Hopkins University Parallel Computing
More informationErlang Capacity of Multi-class TDMA Systems with Adaptive Modulation and Coding
Downloae from orbittuk on: Oct 2, 218 Erlang Capacity of Multi-class TDMA Systems with Aaptive Moulation an Coing Wang, Hua; Iversen, Villy Bæk Publishe in: Proceeings of IEEE ICC 28 Link to article, DOI:
More information1.0 MEASUREMENT OF PARAXIAL PROPERTIES OF OPTICAL SYSTEMS
.0 MEASUREMENT OF PARAXIAL PROPERTIES OF OPTICAL SYSTEMS James C. Wyant Optical Sciences Center University of Arizona Tucson, AZ 8572 jcwyant@u.arizona.eu If we wish to completely characterize the paraxial
More informationMinimization of EMC Filter for Interconnection Inverter by High Switching Frequency
Minimization of EMC Filter for Interconnection Inverter by High Switching Frequency Takuya Kataoka, Masakazu Kato Nagaoka University of Technology Nagaoka, Niigata,Japan takuya_kataoka@stn.nagaokaut.ac.jp
More informationDIELECTRIC ROTMAN LENS ALTERNATIVES FOR BROADBAND MULTIPLE BEAM ANTENNAS IN MULTI-FUNCTION RF APPLICATIONS. O. Kilic U.S. Army Research Laboratory
DIELECTRIC ROTMAN LENS ALTERNATIVES FOR BROADBAND MULTIPLE BEAM ANTENNAS IN MULTI-FUNCTION RF APPLICATIONS O. Kilic U.S. Army Research Laboratory ABSTRACT The U.S. Army Research Laboratory (ARL) is currently
More informationDISCUSSION ON THE APPLICATION OF WIRELESS ACTIVE SENSING UNIT
4 th Worl Conference on Structural Control an Monitoring 4WCSCM-261 DISCUSSION ON HE APPLICAION OF WIRELESS ACIVE SENSING UNI FOR SRUCURAL CONROL C.H. Loh an K.C. Lu National aiwan University, aipei 106-17,aiwan
More information