RADIO SETTING MANUAL

Transcription

1

2 RADIO SETTING MANUAL

3 Transmitter Setup For The JR DSX12 JR-CCPM plays a critical role in coordinating the simultaneous activating of multiple servos to contorl the swashplate. Activation of just a single servo would not lead to control of the swashplate - the three swashplate servos must be controlled in a coordinated fashion. The setup of these servos differs from that for other control functions which control just one servo (for example, the throttle). The initial settings given here must be confirmed on the bench, and then fine tuned after test flying the helicopter. Prior to commencing this process, confirm all the trim levers and trim knowbs on the transmitter are in their neutral (zero) positions. Also shift all switches to position 0 (switches moved away from the operator). Please also be familiar with the instructions for the transmitter. The initial settings can be entered into the transmitter without turning power on to the receiver. Please note that fine adjustment will be needed after test flying the helicopter. 1 Initializing the Radio 1 Press (and hold) the ENT key located on the lower left of the Transmitter,then turn on the power switch. ([System Mode List], List screen displayed) 1 ENT + ON Select[Model SEL] 2 Turn the dial on the right side of the Transmitter to 5 8 select [84.Model SEL] and press. 7 7 To switch[select]and[copy]press the dial alternately Turn the dial to select [Model]and press. 4 Turn the dial to select the model number you want to reset and press the dial again to settle it. Turn the dial to select Select the model to be reset. 5 Use the LIST key to return to System Mode List 6 Turn the dial to select[28.mdl Reset]and press. 7 Press the CLR key and press YES in the YES/ NO confirmation screen. 8 Press the LIST key to return to [Syetem Mode List] Press the function key to reset P.2

4 2 Selecting the Swash Type 1 Turn the dial to select [34.Swash TYPE] and press Turn the dial to select [ 1 s e r v o N O R M ] a n d p r e s s. 3 Turn the dial to select [3servos 120 ]and press. Select by using dial and pressing it 4 Press the LIST key to return to[system Mode List] 5 Press the ENT key twice to return to the regular screen. Turn the dial to select 3 Setting the Swash Mix 1 Press the LIST key on the regular screen. ( Function List is displayed) Turn the dial to select[65.swash MIX]and press Confirm that 3servos 120 is displayed. Now use the dial to move to the item you want to alter. 4 Use the + and - keys to input the values shown in the table below for AILE, ELEV and PIT. (for the GSR260Z, select [+] in [PIT.] and press to swith to [-] 5 After completing these settings press the LIST key to return to[function List] Change the value by using the dial. Move to the item you want to alter. Press the dial to switch between + and - CH-2(AILE) CH-3(ELEV) CH-6(PIT.) GSR260Z P.3

5 4 Setting the Servo Directions (Reverse Switches) 1 Turn the dial to selct[11.rev. SW]and press. 3 2 Select the reverse switch for each channel and press the dial to set NORM or REV. ( Each time the dial is pressed, NORM and REV. are alternately selected.) 1 2 Differs depending on the gyro used 3 After setting is completed for each channel, ues the LIST key to return to the [Function List]. Note the servo directions given are for JR servos. Please confirm the directions carefully for your chosen servos. THRO CH-2(AILE) CH-3(ELEV) RUDD GEAR CH-6(PIT.) GSR260Z ー ル ース ース ー ル ー ル RUDD ロ ー ル / ース ー ル 5 Setting the Travel Adjust Values 1 Turn the dial to select[12.trvl ADJ.]and press. 4 2 Turn the dial to select each item and press. (Select L/R or U/D position by moving the appropriate control in that direction) Turn the dial and enter the values shown in the table below and press. 4 Press the LIST key twice to return to regular screen. L R U D スッ THRO CH-2(AILE) CH-3(ELEV) RUDD GEAR CH-6(PIT.) GSR260Z H 80% L 80% R 100% D 100% U 100% R 100% + 100% - 100% H 100% L( ト ) R( ラト ) スッ RUDD ロサーボストロー Setting for other kind of Radio set 1 If you use a transmitter other than the JR DSX12 or PCM9X II, please refer to the manufactures instruction manual. 2 If using a Futaba transmitter, set the pitch value for Swash Mix about 10% lower than the value in the table. 3 Please refer to your tail gyro instruction manual for advise on tail rotor setup and initial transmitter settings.

6 Trasmitter Setup For The JR PCM9X Ⅱ JR-CCPM plays a critical role in coordinating the simultaneous activating of multiple servos to control the swashplate. Activation of just a single servo would not lead to control of the swashplate - the three swashplate servos must be controlled in a coordinated fashion. The setup of these servos differs from that for other control functions which control just one servo (for example, the throttle). The initial settings given here must be confirmed on the bench, and then fine tuned after test flying the helicopter. Prior to commencing this process, confirm all the trim levers and trim knobs on the transmitter are in their neutral (zero) positions. Also shift all switches to position 0 (switches moved away from the operator). Please also be familiar with the instructions for the trasmitter. The initial settings can be entered into the transmitter without turning power on to the receiver. Please note that fine adjustment will be needed after test flying the helicopter. 1 Initializing the Radio 1 While pressing the ENT key (located at the lower left of the transmitter), turn on the power switch. (System setting mode,list screen displayed) 2 Turn the dial on the right side of the transmitter to select [Model SEL] and press the dial twice. 3 Turn the dial to select the model number you want to reset, and press the dial again. 4 Press the LIST key to return to [SYSTEM M.]. 5 Turn the dial to select [MDL Reset] and press. Select the model to be reset 6 Press the CLR key and press YES in the YES / NO confirmation screen. 2 Selecting the Swash Type 1 Press the LIST key to return to SYSTEM M. again. 2 Turn the dial to select SWASH TYP and press. 3 Turn the dial again to select [3s120 ] and press. 4 Press the LIST key to return to SYSTEM M. 5 Press the ENT key twice to return to the regular screen. P.5

7 3 Setting the Swash Mix 1 Press the LIST key to display Function mode Turn the dial to select Swash Mix and press. 3 Confirm that 3servos 120 is displayed. Use the dial to move to the item you want to alter Use the + or - key to input the values shown in the table below for AILE ELEV and PIT. 5 After setting press the LIST key to return to Function mode. 4 Setting Servo Direction 1 Turn the dial to select REV.SW and press. CH-2(AILE) CH-3(ELEV) CH-6(PIT.) GSR260Z Select the reverse switch of each channel and press the dial to set NORM/REV. ( Every time the dial is pressed,norm and REV are alternately selected.) After setting is completed for each channel,press the LIST key to return to the function mode. THRO CH-2(AILE) CH-3(ELEV) RUDD GEAR CH-6(PIT.) GSR260Z ー ル ース ース ー ル ー ル RUDD ロ ー ル / ース ー ル P.6

8 5 Setting Travel Adjust Values 1 Turn the dial to select TRVL ADJ. and press. 3 2 Use the dial to select each item and press. Set each to the value in the table below and press Press the ENT key to return to the regular screen. L R U D ス ッ THRO CH-2(AILE) CH-3(ELEV) RUDD GEAR CH-6(PIT.) GSR260Z H 80% L 80% R 100% D 100% U 100% R 100% + 100% - 100% H 100% L( ト ) R( ラト ) スッ RUDD ロサーボストロー Setting for other kind of Radio set 1 If you use a transmitter other than the JR X2610 or PCM9X II, please refer to the manufactures instruction manual. 2 If using a Futaba transmitter, set the pitch value for Swash Mix about 10% lower than the value in the table. 3 Please refer to your tail gyro instruction manual for advise on tail rotor setup and initial trasmitter settings. P.7

9 FOR FUTABA Manufactured Transmitters CCPM plays a critical role in coordinating the simultaneous activating of multiple servos to control the swashplate. Activation of just a single servo would not lead to control of the swashplate - the three swashplate servos must be contorolled in a coordinated fashion. The setup of these servos differs from that for other control functions which control just one servo (for example, the throttle). The initial settings given here must be confirmed on the bench, and then fine tuned after test flying the helicopter. Prior to commencing this process, confirm all the trim levers and trim knobs on the transmitter are in their neutral (zero) positions. Also shift all switches to position 0 (Switches moved away from the operator). Please also be familiar with the instructions for the transmitter. The initial settings can be entered into the transmitter without turning power on to the receiver. Also read the instruction manual for your transmitter. Please note that fine adjustment will be needed after test flying the helicopter. 1 Selecting the Swash Type See the instruction manual for your transmitter to select the swash type. Go to the TYPE setting screen in the PARA setting screen to select HELI SR-3 Note that is not HELI SN-3. 2 Setting the Swash Plate Mix Input the values in the table below for each item. 1Ch( ルロ ) 2Ch( ー ー ) 6Ch( ッ ) GSR260Z Setting Servo Reverse Initilally, set the same values as for a JR made Radio set, then confirm. 4 Setting the Travel Adjust Values Initially set the same values as for a JR made Radio set. For the throttle and the rudder, values will depend on the engine and the gyro used. Set values so that each servo will have the optimum travel. 5 Wiring Make connections between the servos and the receiver as shown in the figure below. 9/B 9/B ch6 ch2 スワッシュサーボ Swash Servo R スワッシュサーボ Swash Servo F 1 C ch1 スワッシュサーボ Swash Servo L P.8

10 Wiring Diagram for JR Radios Confirm connections between the servos and the receiver as per the figure below. The lead harnesses of the servos shown in the diagram are color coded simply for easy distinction. When using other makes of Radio set refer to the instruction manual to confirm correct wiring. サーボ Swash スワッシュサーボ Servo F F ELEV ELEV output on Receiver Swash スワッシュサーボ Servo R R AUX1 AUX1 output on Receiver Swash スワッシュサーボ Servo L L AILE output A I LE on Receiver Gyro ロ and Other サーボServo Connections Rudder Servo ラダーサーボ SERVO( output ロ) on Gyro) Gyro sensor ロサー SENSE( input ロon ) Gyro) RUDD(input RUDD( on ロGyro) ) RUDD (output RUDD on Receiver) SELECT(input SELECT( on ロGyro) ) GEAR (output GEARon Receiver) GAIN(input GAIN( on Gyro) ロ) AUX2 (out AUX2 put on Receiver) Throttle スロットルサーボ servo THRO (out THRO put on Receiver) Gyro Sensor スロットルサーボ Throttle Servo Swash スワッシュサーボ Servo F F Receiver Gyro ラダーサーボ Rudder Servo スワッシュサーボ S w a s h S e r v o L S スワッシュサーボ w a s h S e r v o R P.9

11 DATA SHEET MODEL NO.1 MODEL NAME JR GSR260Z CCPM Servo Gyro RUDD Servo N o r m a l :Payload 0 kg S t u n t 1:Payload 4 Kg Slow NOTE Alter the travel adjust for the throttle servo to suit the engine actually used. Adjust the A.D.T.( t r i m ) during flight. The values in the table are standard settings. Confirm them on the bench and make fine adjustments after test flying the helicopter.