November Wireless Data. Mobile phone, ISM900, ISM2.4 & ISM5.8. Wireless Data Improvement & Transfer

Transcription

1 November 2018 Wireless Data Mobile phone, ISM900, ISM2.4 & ISM5.8 Improvement & Transfer

2 Contents page Page 1 of 2 ISM900/ I.o.T./ LoRa - SG-900-TPM series MHz, 6.2 dbi, 800mm - CFD MHz, 2.1 dbi, 400mm - DLD MHz, 2.1 dbi, 280mm - DLD MHz, 2.1 dbi, 230mm - M99BNC MHz, 2.1 dbi, 190mm - ZAU GPS MHz & MHz, 27dB and 0dBi - ZCG-EEH-915 *NEW* MHz, 5.7 dbi, MMCX right-angle - ZSG MHz, 5.1dBi, N-type female in base Modem data - MAG-M90T series Telstra 3G or Optus & Vodafone 3G, 5 dbi, 325mm - MAG-CELL-DB series Telstra 3G & 4G, 3.1dBi, 135mm - GIDM-DB Telstra, Optus & Vodafone 3G, 2.1 dbi, 270mm - GID-M70T *NEW* Telstra, Optus & Vodafone 4G LTE, 5.1dBi, 400mm - GID-M90T series Telstra 3G or Optus & Vodafone 3G, 5.1 dbi, 450mm or 400mm - ZCG-EEH-L01 Telstra, Optus & Vodafone 4G LTE, 4G & 3G, 6.0 dbi & 2.75dBi, 80mm - ZCG-EEH-L01FC Telstra, Optus & Vodafone 4G LTE, 4G & 3G, 6.0 dbi & 2.75dBi, Fixed cable, 80mm - SGDB-TPM Telstra, Optus & Vodafone 4G & 3G, 6.2 dbi & 3 dbi, 800mm, Top only - SGDB-T10 Telstra, Optus & Vodafone 4G & 3G, 6.2 dbi & 3 dbi with MMA & 10 metres cable - SG700-MMA *NEW* Telstra, Optus & Vodafone 4G LTE MHz, specify 50MHz, 5.1dBi, 900mm - SGL2000 Optus 3G upper, MHz, 6.2 dbi - CM1600-4GX *NEW* Telstra 4G LTE, MHz, 8.1dBi, 2.2 metres - CM1600AM & CMG1600AM Telstra 3G, MHz or Optus & Vodafone 3G, MHz, 8.1 dbi, 2.4m - LPY S *NEW* Telstra, Optus & Vodafone 4G LTE, 4G & 3G, 8dBi, 290mm, Log Periodic Yagi - LPY Telstra, Optus & Vodafone 4G LTE, 4G & 3G, 11dBi, 400mm, Log Periodic Yagi - CT800 & CT900 Telstra 3G or Optus & Vodafone 3G, 2.1dBi, low profile, 150mm - GCRFA & GCT Telstra, Optus & Vodafone 4G, 3G, WiFi and GPS, low profile, 100mm diameter - ZAW-9-LTE Telstra, Optus & Vodafone 4G LTE, 4G, 3G, GPS & WiFi/WLAN, low profile, 85mm diameter - ZAU-9-LTE Telstra, Optus & Vodafone 4G LTE, 4G, 3G, GPS/GLONASS & WiFi/WLAN, low profile, 85mm diameter - ZAU-3C series Telstra 3G and GPS, low profile, 64.5mm diameter - ZAU-3S series Telstra 4G, 3G & GPS, low profile, 64.5mm Road embedded antenna - ZRPM Raised road marker embedded antenna, 915 & 2400MHz, 3dBd - Red/yellow/white or specify GHz collinear - CFD MHZ, 2.1 dbi, 220mm - SG1885-TPM GHz, 5.14 dbi, 500mm - MD1800B & MD1800B-MGB GHz, 2.1dBi, 320mm - MD GHz, 2.1dBi, 300mm M.I.M.O. Multiple In, Multiple Out - Y1809-MIMO GHz, 11.3dBi per plane, 345mm - Y2009-MIMO GHz, 11.3dBi per plane, 290mm - ZD8Z-XP-MIMO MHz & MHz, 8dBi Nominal, N-type Female - ZD8Z-XP-716-MIMO MHz & MHz, 8dBi Nominal, 7/16 DIN Female D.E.C.T. Yagi - Y1809-DECT GHz, 11.3 dbi, 300mm x 80mm, Mast Mount - Y1818-DECT GHz, 15.3 dbi, 950 x 80mm, Mast Mount

3 Contents page Page 2 of 2 ISM2.4 or WiFi band - MD GHz, 2.1 dbi, 230mm, Stud Mount Collinear - SG GHz, 5.14 dbi, 550mm or 380mm, Stud or Flange Mount - Z GHz, 10 dbi, 850mm, Mast Mount Collinear - Z RS GHz, 13 dbi with rear screen fitted, 850mm x 150mm - DLD GHz, 2.1 dbi, 115mm, Stud Mount - WH GHz, 2.1 dbi, 74mm - ZAW-WiFi-4S GHz, 0 dbi, Adhesive mount - CP GHz, 17.1 dbi, 1.12 metres, Mast Mount, Right Hand Circular - Y & Y GHz, 11.3 dbi or 17.8 dbi, 300mm or 700mm, Mast Mount - PD-240N GHz, Power Divider, 80mm x 50mm - ZCG-EEH-201*NEW* & GHz, 4dBi, specify cable length and connector, 74.6mm - GCT , 0dBd, 50W, low profile, 100mm diameter GHz collinears - Z & Z GHz or GHz, 10 dbi, 820mm or 810mm 2.65GHz Yagi - Y & Y GHz, 11.3 dbi or 17.8 dbi, 300mm or 700mm, Mast Mount 3.5GHz Collinear/dipole - Z GHz, 10 dbi, 850mm, mast mount collinear - DLD GHz, 2.1dBi, 95mm - stud mount dipole ISM 5.8 band - CP GHz, 14 dbi, 180mm, Mast Mount, Right Hand Circular - Z GHz, 5.2dBi, 250mm - Z & Z GHz, 8dBi, 575mm or 10dBi, 675mm Antenna installation accessories How to order Terms and conditions of sale Contact us

4 SG900-TPM series UHF MHz Wireless data collinear The SG900 series will significantly improve your wireless data transmit and receive capabilities for radio location, industrial, scientific or medical applications., adaptors, water-proofing and other installation accessories are all available separately. SG900-W-TPM SG900-B-TPM Colour White Black Coloured fibreglass radome, aluminium ferrule, cap and cable assembly MHz Tuning Factory Factory Gain 6.2 dbi 6.2 dbi Impedance Polarisation Vertical Vertical H Plane Cable 360 omni-directional 4.5 metres RG58 stranded - side exit from ferrule FME female fitted to cable - for ease of installation Height 800mm 800mm Weight 790grams 790grams (order separate) Bracket mounting: GM1, GM2, GM4, GM6 or A-6211 Mast mounting: 4266 Mount as high on your vehicle,structure, mast or tower as possible using the appropriate mounting bracket.

5 CFD890 UHF MHz Spread spectrum dipole The CFD890 spread spectrum dipole is specifically designed for wireless data link and N.F.C. (Near Field Communications) within the UHF MHz range. No metal ground plane is necessary for the antenna to operate effectively., coaxial feeder cable, adaptors and other installation accessories are all available separately. Bandwidth VSWR Tuning Gain Impedance - nominal Maximum power DC grounding Polarisation H Plane Cable Height Weight (order separate) CFD890 Black fibreglass radome, aluminium ferrule and cable assembly UHF MHz Full band <1.5:1 full band Factory 2.1 dbi 20 Watts Yes Vertical 360 omnidirectional 3 metres RG58 low loss - side exit ferrule SMA male fitted to cable - or specify another cable 400mm 350grams Any 13mm hole or bracket with 13mm hole Bracket: GM1, GM2, GM4, GM5 or A-6211 Mount: BBM-SS, BBML-SS, BBMXL-SS or MRM-SS Mount as high on your structure, mast or tower as possible using an appropriate mounting bracket

6 DLD860 UHF MHz Stud mount data link dipole The DLD860 is a stud mount dipole specifically for wireless data link or N.F.C. (Near Field Communications) within the UHF MHz range., coaxial feeder cable, adaptors and other installation accessories are all available separately. Bandwidth VSWR Tuning Gain Impedance - nominal Maximum power DC grounding Polarisation H Plane Cable Height Weight (order separate) DLD860 Black PVC radome and black delrin mount ferrule MHz Full band <1.5:1 full band Factory 2.1 dbi 20 Watts Yes Vertical 360 omni-directional 1.8 metres RG316 - bottom exit from ferrule SMA male fitted as standard - or specify requirements 280mm 50grams Bracket: GM1, GM2 or GM6 Mount as high on your structure, pole or mast as possible using the a hole or appropriate mounting hardware with a minimum 12.7mm hole. Do not mount near any vertical metallic objects.

7 DLD900 UHF MHz Stud mount data link dipole The DLD900 is a stud mount dipole specifically for wireless data link or N.F.C. (Near Field Communication) purposes within the UHF MHz range., coaxial feeder cable, adaptors and other installation accessories are all available separately. Bandwidth VSWR Tuning Gain Impedance - nominal Maximum power DC grounding Polarisation H Plane Cable Height Weight (order separate) DLD900 Black PVC radome and black delrin mount ferrule MHz Full band <1.5:1 full band Factory 2.1 dbi 20 Watts Yes Vertical 360 omni-directional 900mm RG174 - bottom exit from ferrule SMA male fitted as standard - or specify requirements 230mm 50grams Bracket: GM1, GM2 or GM6 Mount as high on your structure, pole or mast as possible using the a hole or appropriate mounting hardware with a minimum 12.7mm hole. Do not mount near any vertical metallic objects.

8 M99BNC900 Wireless data link flexible whip UHF MHz The M99BNC900 is a highly flexible whip specifically designed for wireless data link or NFC (near field communications) within the MHz range. Coaxial feeder cable, adaptors and other installation accessories are all available separately. Bandwidth VSWR Tuning Gain Impedance - nominal Maximum power Polarisation H Plane Height Weight Mounting capability M99BNC900 Black heatshrunk whip and chrome connector MHz Full band <1.5:1 full band Factory 2.1 dbi BNC male as base 25 Watts Vertical 360 omni-directional 195mm 26grams BNC male fits to any BNC female terminated device Mount as high on your structure or device as possible. If using on a device, ensure not enclosed within metallic surfaces or metallic lined walls.

9 ZAU GPS and ISM Low profile antenna The ZAU GPS and Data transmission antenna is perfect for AVL tracking, GPS navigation and telemetry applications, all within a low profile, fully water-proof design. Adaptors, patch leads and other installation accessories are all available separately. GPS Data Black moulded radome Frequency Range MHz MHz Bandwidth 2MHz Full band Gain 27 db typical 0 dbi Polarisation Right-hand circular Linear Noise Figure 2.0 maximum N/A VSWR <1.8:1 <2.0:1 (with 5m cable) Impedance Power Supply 3.0 ~ 5.5V DC N/A Power Consumption 12mA N/A Power Handling N/A 10 Watts Dimensions Operating Temperature Storage Temperature (suplplied) Specify requirements when ordering 118.4mm length x 55.5mm width x 12.3mm high -40 C to +80 C -45 C to +100 C 3M double sided adhesive pad - 1mm 928MHz Updated 27th August 2018

10 ZCG-EEH-915 ISM900 low profile antenna MHz The ZCG-EEH-915 fixed cable low profile antenna is designed for ISM900 applications such as IoT and data transfer. Being an enclosed unit, the internals are weatherproofed to ensure a long service life. Ideal applications for the ZCG-EEH-915 are: - Wireless monitoring - LoRa (long range) data communications - I.o.T. applications (internet of things), adaptors, coaxial cable, connectors and other installation accessories are all available separately. Bandwidth VSWR Tuning Gain Maximum power Impedance Polarisation Cable Operating temperature Storage temperature Dimensions Weight ZCG-EEH-915 Black radome, rubber gasket, chrome fittings and external cable ISM900: MHz Full band 2.7:1 across full band Factory 5.8dBi 5 Watts Linear, Vertical 150mm x H bottom exit from antenna MMCX right-angle fitted, or specify requirements -40 C to +80 C -40 C to +85 C 42mm diameter x 75.6mm height 121grams 13.4mm mounting thread,rubber gasket, toothed washer and nut (supplied)

11 ZSG MHz Whip antenna Wireless data The ZSG-1977 is designed to be rugged with high gain capability, this antenna is ideal for ISM band applications. The ZSG-1977 is easy to assemble and designed for outdoor applications on either a tower or structure. Please note: the N-type female is located inside the removable mount section to assist with weather protection. Waterproofing should still be applied to the termination., water-proofing, bird-proofing and other installation hardware are all available separately. ZSG-1977 Black stainless steel whip, aluminium radials and anodised aluminium mount section UHF MHz Bandwidth Full band Tuning Factory Gain 5.1dBi Maximum power 5 Watts Impedance Polarisation Vertical H Plane 360 omni-directional Mount section N-type female at base of antenna - inside mount section 200mm x 32mm anodised aluminium EB1-SS Height 615mm Width (order separate) 250mm Mast mounting: 2 x EB1-SS or 1 x UB3-SS or Side/wall mounting: 1 x NSM-CL3642 UB3-SS Mount as high on your structure/mast or tower as possible using the appropriate mounting hardware, ensuring no obstructions. NSM-CL3642

12 MAG-M90T Series Telstra 3G or Optus & Vodafone 3G Magnetic base mobile phone/wireless data improvement The MAG-M90T series of indoor detachable magnetic base antennas will enhance the reception of your mobile phone or wireless data device. The MAG-M90T series are easy to set-up, easy to remove and the detachable whip makes the antenna easy to store when not required., adaptors and other installation accessories are all available separately. MAG-M90T800 MAG-M90T900 Black stainless steel whip, moulded magnetic base, cable assembly and gold plated/tri-metal plate terminations VSWR Telstra 3G (Next G ) MHz Optus & Vodafone 3G MHz <1.5:1 across full band chosen Tuning Factory Factory MAG-M90T800 Telstra 3G (Next G ) Gain - nominal 5 dbi 5 dbi Maximum power 5 Watts 5 Watts Impedance Polarisation Vertical Vertical - fitted Cable assembly Magnetic Base: FME Male Magnetic Base Cable: FME Female Cable Termination: SMA Male 5 metres RG58 low loss - supplied Height 325mm 325mm Weight 60grams 60grams As high on your vehicle or structure on any flat magnetic metal surface MAG-M90T900 Optus & Vodafone 3G

13 MAG-CELL-DB series Telstra 4G and 3G Magnetic base mobile phone/wireless data improvement The MAG-CELL-DB series of magnetic base antenna is specifically designed for use to improve reception of the Telstra 4G and 3G (Next G ) mobile phone and wireless data networks. With a magnetic mount base, the MAG-CELL-DB series can be easily installed and removed in situations where theft/vadalism or damage may occur. The MAG-CELL-DB is just the removable magnetic base with radiating whip attached. The MAG-CELL-DB-2 comes standard with the magnetic radiating whip base and a 2.0 metre cable assembly ready for installation. Alternative cable assemblies, adaptors, connectors and other installation accessories are all available separately. MAG-CELL-DB MAG-CELL-DB-2 MAG-CELL-DB Black plastic and nickel Black plastic and nickel and cable assembly Frequency Range Telstra 4G & 3G MHz & MHz VSWR <2:1 full band <2:1 full band Tuning Factory Factory Gain (nominal) 3.1 dbi 3.1 dbi Maximum Power 5 Watts 5 Watts Impedance Polarisation Vertical Vertical - fitted FME male inside magnetic base Height 135mm 135mm SMA Male fitted to end of cable MAG-CELL-DB-2 Weight 60grams 80grams Mounting Hardware Specify cable assembly & connectors (order separate) 2 metre cable assembly with SMA connector fitted Mounting Position As high on your vehicle or structure on any flat magnetic metal surface

14 GIDM-DB Telstra, Optus & Vodafone 3G Mobile phone and wireless data improvement The GIDM-DB is a ground independent antenna is specifically designed and manufactured for full coverage of the Telstra, Optus and Vodafone 3G (Next G ) network for wireless data and mobile phone improvement., adaptors, connectors and other installation accessories are all available separately. Frequency Range Bandwidth VSWR Tuning Gain Maximum Power Impedance Polarisation Cable GIDM-800 Black moulded whip, chrome and black nylon elevated feed base and cable assembly Telstra, Optus & Vodafone 3G (Next G ) MHz Full band <1.6:1 full band 1.6:1 VSWR 2.1 dbi 5 Watts Vertical 4.5 metres RG58 low loss - bottom exits base FME female fitted to cable - for ease of installation Height 220mm Weight (order separate) 280grams Secure to any minimum 10mm hole or appropriate bracket with a minimum 10mm hole using the split nut attached such as the GM5 As high on your structure as possible using an appropriate mount hole or bracket

15 *NEW* GID-M70T/M90T Series 4G LTE, Telstra 3G or Optus & Vodafone 3G Mobile phone/ wireless data improvement GID-M90T ground independent antennas are useful for mobile phone and data network coverage improvements within the 4G LTE or 3G. These models are a modest size and will deliver excellent performance. No metal ground plane is necessary for the antenna to operate effectively., coaxial feeder cable, connectors and other installation accessories are all available separately. GID-M70T - *NEW* GID-M90T-NextG-SS GID-M90T-GSM Black powdercoated phase coil whip, stainless steel and delrin base and coaxial cable assembly Black powdercoated phase coil whip, chrome and delrin base and coaxial cable assembly 4G LTE MHz Telstra 3G MHz Optus & Vodafone 3G MHz VSWR <1.6:1 full band <1.6:1 full band <1.6:1 full band Tuning Factory Factory Factory Gain 5.1 dbi 5.1 dbi 5.1 dbi Maximum power 5 Watts 5 Watts 5 Watts Impedance Polarisation Vertical Vertical Vertical Cable 4.5 metres RG58 low loss exits bottom of base FME female fitted to cable - for ease of installation Height 400mm 450mm 400mm Weight 350grams 350grams 350grams (order separate) Secure to any minimum 10mm hole or appropriate bracket with a minimum 10mm hole using the split nut attached. As high on your vehicle/ structure as possible using an appropriate mount hole or bracket GM1 GM4 BBM-SS A-6211

16 ZCG-EEH-L01 Telstra, Optus & Vodafone 4G LTE, 4G and 3G Low profile mobile phone/wireless data improvement Ideal applications for the ZCG-EEH-L01 are: - Wireless data communications - Wireless monitoring/ telemetry - Mobile phone network improvement, cable assemblies and other installation accessories are all available separately. ZCG-EEH-L01 ZCG-EEH-L01FC Black radome, rubber gasket and chrome termination Telstra, Optus and Vodafone 4G LTE, 4G and 3G (NextG ) & MHz Bandwidth Full band Full band VSWR <2.7:1 across full band <2.7:1 across full band Tuning Factory Factory Gain 6.0dBi at MHz and 2.75dBi at MHz Maximum power 5 Watts 5 Watts Impedance Polarisation Linear, Vertical Linear, Vertical N-type female bulkhead in base FME female to cable Cable - 2m RG58 - bottom exit Operating temperature -40 C to +80 C -40 C to +80 C Storage temperature -40 C to +85 C -40 C to +85 C Dimensions Diameter: 42mm, Height: 75.6mm Weight 121grams 121grams (order separate) Use suitable bracket/hole with a 16mm hole such as GM1 or GM6, using the rubber gasket, toothed washer and hex nut supplied Mount as high on vehicle/structure as possible using appropriate bracket or mount hole. Waterproof rating IP67 IP67

17 ZCG-EEH-L01FC 4G LTE, 4G and 3G Fixed Cable Low profile Antenna The ZCG-EEH-L01FC fixed cable low profile antenna will improve mobile phone device reception and transmission range. Being an enclosed unit, the internals are weatherproofed to ensure a long service life. Ideal applications for the ZCG-EEH-L01FC are: - Data communication - Wireless monitoring - Mobile phone network improvement, adaptors, coaxial cable, connectors and other installation accessories are all available separately. Bandwidth VSWR Tuning Gain Maximum power Impedance Polarisation Cable Operating temperature Storage temperature Dimensions Weight ZCG-EEH-L01FC Black radome, rubber gasket, chrome fittings and external cable Telstra, Optus and Vodafone: 4G LTE, 4G and 3G & MHz Full band <2.7:1 across full band Factory 6.0dBi MHz & 2.75dBi MHz 5 Watts Linear, Vertical 2.0m x RG58 bottom exit from antenna FME female fitted with red heatshrink/identification -40 C to +80 C -40 C to +85 C 42mm diameter x 75.6mm height 121grams 13.4mm mounting thread,rubber gasket, toothed washer and nut (supplied)

18 SGDB-TPM series Telstra, Optus & Vodafone 4G and 3G Mobile phone/wireless data improvement At some remote locations, inside a building or whilst travelling, mobile phone and wireless data reception can often be poor, the SGDB-TPM is an adaptable antenna for mounting outdoors at your home or office. The SGDB-TPM can be used as the replacement top for the SGDB series., adaptors, bird-proofing and other installation accessories are all available separately. Colours available SGDB-TPM series Black SGDB-B-TPM White SGDB-W-TPM Bandwidth VSWR Tuning Gain Maximum power Impedance Polarisation H Plane Coloured fibreglass radome, aluminium mount ferrule and cable assembly Telstra, Optus & Vodafone 4G and 3G MHz & MHz Full band <1.6:1 across full band Factory 6.2dBi at MHz and 3dBi at MHz 30 Watts Vertical 360 omni-directional E Plane 32 Cable Height Weight (order separate) 5 metres RG58 low loss - side exit from ferrule FME female fitted to cable - for ease of installation 800mm 700grams Bracket: GM1, GM2, GM6 or a minimum13mm hole Mast Mount: 4266 As high on your structure/tower or building as possible, using the appropriate mounting hardware.

19 SGDB-T10 Series Telstra, Optus & Vodafone 4G and 3G Mobile phone/wireless data improvement The SGDB-T10 super gain telemetry antenna is a popular choice to improve your mobile phone or wireless data reception. The SGDB-T10 is different from the standard SGDB due to the capability of mast mounting to a pole or vertical mast and the cable exiting the base of the mounting section., adaptors, coaxial feeder cable and other installation accessories are all available separately. Bandwidth VSWR Tuning Gain Maximum power Impedance Polarisation H Plane SGDB-T10 Black fibreglass radome, aluminium ferrule, mast mount adaptor and cable assembly Telstra, Optus & Vodafone 4G and 3G MHz & MHz Full band <1.6:1 across full band Factory 6.2dBi MHz and 3dBi MHz 30 Watts Vertical 360 omni-directional E Plane 32 Cable Height Weight (order separate) 10 metres RG58 low loss - bottom exit from base Gold plated SMA male fitted to cable - or specify 900mm 900grams 2 x EB1-SS or 1 x UB3-SS As high on your mast/tower or structure as possible using the appropriate clamp/s

20 SG700-MMA Super gain 4G LTE or 3G Collinear collinear The SG700-MMA super gain 4G LTE mast mount collinear offers good performance combined with our robust tried and tested ZCG quality SG series construction. Suitable for low power omni-directional wireless data applications., adaptors, bird-proofing and other installation accessories are all available separately. Bandwidth Tuning VSWR Gain Maximum power Impedance Polarisation H Plane SG700-MMA White fibreglass radome, aluminium ferrule and mast mount adaptor and cable assembly 4G LTE MHz Specify 50MHz when ordering or specify 4GLTE MHz Factory <1.5:1 within specified 50MHz 6.2 dbi 30 Watts Vertical 360 omni-directional E Plane 32 Cable 4.5 metres RG58 low loss - side exit from ferrule BNC male fitted as standard or specify requirements EB1-SS UB3-SS Height 900mm Weight 900grams (order separate) 2 x EB1-SS or 1 x UB3-SS - parallel or 2 x UB2-SS - right-angle Mount as high on your structure, pole or tower as possible using the appropriate mounting clamps. UB2-SS

21 SGL2000 Series Telstra, Optus & Vodafone 3G upper Mobile phone/wireless data improvement The SGL2000 series are specifically designed for the Telstra, Optus & Vodafone 3G upper mobile phone network, and offers consistent and dependable performance with maximum efficiency, particularly where signal strength is poor., adaptors, alternative connectors and other installation accessories are all available separately. Colours available Bandwidth VSWR Tuning Gain Maximum Power Impedance Polarisation H Plane Cable Height Weight (order separate) SGL2000 Black: SGL2000-B, White: SGL2000-W, Brown: on request Coloured fibreglass radome, aluminium ferrule and cap, stainless steel parallel spring and cable assembly Telstra, Optus and Vodafone 3G upper MHz Full band <1.6:1 across full band Factory 6.2 dbi 30 Watts Vertical 360 omnidirectional 5 metres RG58 low loss - bottom exit from spring FME female - supplied, not fitted 480mm 600grams Bullbar: BBM-SS, BBML-SS or BBMXL-SS Truck Mirror: MRM-SS Bracket Mounting: GM1, GM2, GM4, GM6 As high on your vehicle/structure as possible using a minimum 16mm hole or appropriate bracket with a 16mm hole FME female supplied, not fitted

22 *NEW* CM series New 4G LTE, Telstra 3G or Optus & Vodafone 3G Mobile phone and data improvement These mast mount models offer the maximum gain and reception range practical in a omnidirectional, mobile phone or wireless data fixed position antenna., coaxial feeder cable, connectors and other installation accessories are all available separately. *NEW* CM1600-4GX CM1600AM CMG1600AM-AC White fibreglass radome, stainless steel mount tube and tri-metal plated termination 4G LTE/ 4G Plus/ 4GX MHz Telstra 3G (Next G ) MHz Optus & Vodafone 3G 890MHz-960MHz VSWR Better than <1.5:1 VSWR across full band Tuning Factory Factory Factory Gain 8.1dBi 8.1 dbi 8.1 dbi Maximum power 20 Watts 20 Watts 20 Watts Impedance DC grounding Yes Yes Yes Polarisation Vertical Vertical Vertical H Plane 360 omni-directional E Plane N-type female in base of mount tube - no cable Height 1.85 metres 2.4 metres 2.4 metres Weight 700grams 700grams 700 grams Mount section 420mm x 20mm 420mm x 20mm 420mm x 20mm (order separate) Mast mounting: 2 x EB1-SS or 1 x UB3-SS Side/wall mouting: 2 x NSM-B20M Mount as high on your mast/tower or structure using the appropriate clamps.

23 LPY series Mobile phone 4G LTE, 4G and 3G Radome enclosed log periodic Yagi The LPY series of radome enclosed log periodic Yagis provides exceptionally broad bandwidth coverage across the 4G LTE, 4G and 3G mobile phone networks & MHz. Coaxial feeder cable, connectors and other installation accessories are all available separately. LPY S LPY White PVC radome and aluminium mounting hardware 4G LTE/4G Plus/ 4GX, 4G and 3G MHz & MHz Bandwidth Full band Full band VSWR <1.5:1 across full band Tuning Factory Factory Gain 8 dbi 11 dbi Maximum power 100 Watts 50 Watts LPY S Impendance - nominal Polarisation Mount horizontal, vertical or +/- slant as required H Plane E Plane DC grounding Yes Yes N-type female fitted to 200mm white RG58 stranded Dimensions Length: 290mm, Width: 65mm, Height: 210mm Length: 400mm, Width: 60mm, Height: 260mm Weight 1.5kg 1.5kg Wind Load at 160kph (supplied) Front: 1.653kg, 0.016kN Side: 7.377kg, 0.072kN Front: 1.89kg, 0.019kN Side: kg, 0.123kN Adjustable angle plate clamp and 2 x 40-50mm diameter U-bolts Mount as high on your structure, pole, mast or tower as possible using a maximum 50mm diameter pole. Adjust the polarisation of the antenna using the mounting holes on the mount bracket. LPY

24 If you require a mobile phone or wireless data network antenna which is small, inconspicuous and virtually indestructable, then the CT800 for Telstra 3G (Next G ) or the CT900 for Optus & Vodafone 3G antenna will be your solution. These low profile antenna are an ideal solution where there is vulnerablity to vandalism, theft or damage. Applications suited for these antennas are: CT800 and CT900 Telstra 3G or Optus & Vodafone 3G Low profile and rugged Trains Buses Forklifts Tractors Forestry Vehicles Logging Trucks Police Ambulance Fire Brigade Military Vehicles Security Services Mining Vehicles CT800 CT900 Aluminium, delrin and tri-metal plated terminations Frequency Range Telstra 3G (Next G ) MHz Optus & Vodafone 3G MHz Bandwidth Full band Full band VSWR <1.6:1 full band <1.6:1 full band Tuning Factory Factory Gain (nominal) 2.1 dbi 2.1 dbi Maximum Power 5 Watts 5 Watts Impedance Polarisation Vertical Vertical H Plane E Plane (fitted) Dimensions Near 360 omni-directional Same as a normal 1/4 λ (wave) whip N-type female mounted at base of antenna Length: 150mm; Width: 32mm; Height: 32mm Weight 170grams 170grams Mounting Hardware Mounting Position 2 x M6 bolts - not supplied As high on your vehicle/ structure as possible, on a metalground plane.

25 GCFRA and GCT Mobile phone/wireless data/wifi and GPS Page 1 of 2 The GCT low profile all-in-one antenna will improve reception for all mobile phone/wireless data networks and GPS. The GCFRA low profile all-in-one antenna will improve mobile phone/ wireless data, GPS and WiFi reception., adaptors and other installation accessories are all available separately. GCFRA GCT Cream ABS polycarbonate radome Mobile phone coverage Telstra, Optus & Vodafone 4G and 3G MHz & MHz GPS frequency MHz MHz GCT Mobile Phone & GPS WiFi ability Yes 2.4GHz No Tuning Factory Factory Impedance H Plane 360 omnidirectional Weight 280grams 280grams Dimensions Cable 3 x 5 metre RG174/U Diameter: 100mm, Height: 39mm 1 x 5 metre RG174/U 1 x 5 metre RG58/AU GCFRA Mobile Phone, GPS & WiFi - fitted 3 x SMA male 2 x SMA male Mounting requirements Any bracket or flat surface with 20mm hole using cream ABS nut and attached rubber gasket supplied As high on your vehicle/structure as possible using a minimum 20mm hole or bracket with 20mm hole. Detailed specifications on next page...

26 GCFRA and GCT Mobile phone/wireless data/wifi and GPS Page 2 of 2 Mobile Phone Antenna GCFRA and GCT Frequency coverage Tuning and VSWR Impedance Pattern Maximum power GPS Active Patch Antenna Frequency coverage Tuning and VSWR Bandwidth Axial ratio Impedance Peak gain Polarisation Telstra, Optus & Vodafone 4G and 3G MHz and MHz Factory tuned to <2:1 across entire frequency 360 omnidirectional 25 Watts GCFRA and GCT MHz ± 3MHz Factory tuned to 1.5:1 minimum 20MHz minimum at -10dB 3 db typical 4 dbic minimum (7cm x 7cm ground plane) Right-hand Circular Amp. Module Amp. Gain Noise Figure Output VSWR DC Voltage DC Current Type A. Type B. 27 db Typical 1.4 db typical 1.4 db typical 2.0 maximum 3.0 V V 2.7 V V 22 ± 5 ma 8.5 ± 4.5 ma WiFi Antenna GCFRA (GCT not Supported) Frequency coverage Tuning and VSWR Impedance Pattern Maximum power Ghz Factory tuned to <2:1 across specified frequency 360 omnidirectional 25 Watts

27 ZAW-9-LTE GPS, mobile phone and WiFi Low profile antenna The ZAW-9-LTE is designed and manufactured for GPS, Mobile Phone and WLAN applications all inside one low profile antenna suitable for A.V.L or fleet management. The ZAW-9-LTE incorportates an internal state-of-the-art low noise amplifier for the GPS patch antenna., adaptors, connectors, patch leads and other installation accessories are all available separately. GPS Mobile Phone WiFi/ WLAN Black plastic radome, chrome mounting base, rubber gasket and cable assemblies MHz 4G LTE, 4G and 3G MHz & MHz GHz & GHz Bandwidth 43MHz at S11<-10dB Full band Full band Gain 27dB at 3V 6.1dBi at MHz 5.47dBi at MHz 3.9dBi at GHz 3.3dBi at GHz Polarisation Right-hand Circular Linear, Vertical Linear, Vertical Noise figure 1.2 maximum N/A N/A Attenuation 20dB min at FO ± 50MHz N/A N/A VSWR Better than 1.5:1 Better than 2.4:1 full band Better than 1.7:1 full band Impedance Power supply 3.0~5.5 Volts DC Consumption 6.1~13mA N/A Power Handling of 10W Cables Dimensions Not terminated, specify requirements when ordering 2 x 10 metre RG58 Low Loss 1 x 10 metre RG174 Diameter: 85mm, Height: 41.5mm Operating temperature -40C to +80 Storage temperature -40C to +85C (supplied) Mount using the attached wing nut Mount as high on your vehicle or structure as possible ensuring no obstructions

28 ZAU-9-LTE Mobile phone, GPS and WiFi Low profile antenna The ZAU-9-LTE low profile antenna is suitable for 4G LTE, GPS and WiFi applications such as vehicle tracking and data aquisition. The radome enclosed internals ensures a water-proof seal for a long reliable service life in the harshest of environments., adaptors and other installation accessories are all available separately. GPS 4G LTE, 4G & 3G WLAN/WiFi Black ABS radome, chrome mounting base and rubber gasket MHz - L1 band 1602MHz - GLONASS MHz MHz GHz GHz Bandwidth 43MHz at S11 <-10dB Full band Full band VSWR <1.5:1 <2.4:1 <1.7:1 Gain 27dB at 3V 6.1dBi MHz 5.47dBi MHz 3.9dBi GHz 3.3dBi GHz Impedance - nominal Attenuation 20dB min. at FO ± 50MHz - - Noise Figure 1.2 maximum - - Power supply 3-5.5Volts DC Consumption mA - 10 Watts power handling Polarisation Right-hand circular Vertical - linear Vertical - linear Height Diameter: 85mm, Height: 41.5mm SMA male as standard or specify requirements Cable 10 metres RG metres RG58 10 metres RG58 Operating temp. Storage temp. -40 C to +80 C -40 C to +85 C Mount as high on your vehicle or vessel as possible using the attached mounting hardware and rubber gasket. Updated 18th August 2016

29 ZAU-3C Series GPS and Telstra 3G Low profile antenna For both Automatic Vehicle Location (A.V.L.) systems and mobile phone improvement, the ZAU series deliver a highly sensitive multiband solution for fleet management., adaptors, connectors and other installation accessories are all available separately. GPS Mobile Phone Black plastic radome, chrome mounting base MHz Telstra 3G MHz Bandwidth 10MHz Full band Gain 27 db typical 1.0 dbi Polarisation Right-hand circular N/A Noise figure 1.8 maximum N/A Attenuation 20 db FO ± 50MHz N/A VSWR <1.5:1 across bandwidth <1.5:1 full band Impedance Power supply Power consumption Volts DC/ 13 ma Power handling capacity 10 Watts - fitted SMA male FME female Dimensions 64.5mm diameter x 14mm high Operating temperature -40 C to +85 C -40 C to +85 C Storage temperature -45 C to +100 C -45 C to +100 C (order Seperate) Bullbar: BBM-SS, BBML-SS or BBMXL-SS Truck Mirror: MRM-SS Bracket Mounting: GM1, GM2, GM4, GM6 As high on your vehicle as possible using a minimum 13mm hole or appropriate bracket with a 13mm hole Model names on next page...

30 Section 3 Vehicle Mount ZAU-3C Series GPS and Telstra 3G Low profile antenna Order/Model Name Coverage Cable Length /s ZAU-3C2M-GC ZAU-3C3M-GC ZAU-3C5M-GC ZAU-3C5M-GC-FAKRA GPS Telstra 3G GPS Telstra 3G GPS Telstra 3G GPS Telstra 3G 2 x 2.0m RG174 2 x 3.0m RG174 2 x 5.0m RG174 2 x 5.0m RG174 FME female - mobile phone SMA male - GPS FME female - mobile phone SMA male - GPS FME female - mobile phone SMA male - GPS Fakra blue - mobile phone Fakra violet - GPS

31 ZAU-3S Series GPS, GPRS and 4G & 3G Low profile antenna For Automatic Vehicle Location (A.V.L) systems, General packet radio service (G.P.R.S.) packet orientation data service and mobile phone improvement, the ZAU-3S series deliver a highly sensitive multiband solution for fleet management, in a low profile, small device., adaptors, connectors and other installation accessories are all available separately. GPS/GPRS Mobile Phone Black plastic radome, chrome mounting base MHz 4G & 3G MHz & MHz Bandwidth N/A Full band Gain 26 db typical 1.0 dbi Polarisation Right-hand circular N/A Noise figure 1.2 maximum N/A Attenuation 20 db FO ± 50MHz N/A VSWR <1.5:1 across bandwidth <1.5:1 full band Impedance Power supply Power consumption Volts DC/ 13 ma Power handling 10W maximum Dimensions 64.5mm diameter x 13.6mm high Operating temperature -40 C to +85 C -40 C to +85 C Storage temperature -45 C to +100 C -45 C to +100 C Mounting requirements Onto any flat magnetic metal surface using magnetic base As high on your vehicle/structure as possible using any magnetic metal surface. Model Order Codes Details s ZAU-3S3M-GC 2 x 3m RG174 SMA male - both ZAU-3S5M-GC 2 x 5m RG174 Fakra violet and blue ZAU-3S7M-GC 2 x 7m RG174 SMA male - both

32 Section 2 Fixed Position ZRPM Embedded data antenna 915MHz and 2.4GHz The ZRPM is a raised pavement marker data antenna. Currently in use for data collection from highway monitoring equipment. It is designed and manufactured to ensure long term survival and will deliver reliable performance, low profile and vandal resistant. These antenna s perform at high efficiencies in a small package. Designed to be mounted directly onto the road pavement, just like a standard road marker. These antennas have been potted with the same epoxy that secures the road marker to the road surface. No air gaps inside the road marker to maintain the mechanical integrity. Colours available Tuning Gain Maximum power Impedance - nominal DC grounding Polarisation Cable Height ZRPM Red, white or yellow - or specify requirements High impact PVC, FR4 PCB, 915MHz and 2.4GHz Factory 3 dbd 10 Watts Yes Vertical SMA male fitted as standard - or specify requirements 2.0 metres H100 side exits from PVC 18mm Weight 0.250g (order separate) Adhesive

33 CFD1420 UHF MHz Spread spectrum dipole The CFD1420 spread spectrum dipole is specifically designed for the UHF MHz range. No metal ground plane is necessary for the antenna to operate effectively., coaxial feeder cable, adaptors and other installation accessories are all available separately. Bandwidth VSWR Tuning Gain Impedance - nominal Maximum power DC grounding Polarisation H Plane Cable Height Weight (order seperate) CFD1420 Black fibreglass radome, aluminium ferrule and cable assembly UHF MHz Full band <1.5:1 full band Factory 2.1 dbi 20 Watts Yes Vertical 360 omni-directional 3 metres RG58 low loss - side exit from ferrule SMA male fitted to cable - other connectors available 220mm 300grams Any 13mm hole or bracket with 13mm hole Bracket: GM1, GM2, GM4, GM5 or A-6211 Mount: BBM-SS, BBML-SS, BBMXL-SS or MRM-SS Mount as high on your structure, mast or tower as possible using an appropriate mounting bracket

34 SG1885-TPM UHF GHz Wireless data link collinear The SG1885-TPM omnidirectional data link collinear is specifically designed and manufactured for use within the UHF GHz range. The SG1885-TPM is ideal for external mounting to a mast, building or vehicle., coaxial feeder cable, adaptors and other installation accessories are all available separately. Specificaitions Bandwidth VSWR Tuning Gain Impedance - nominal Maximum power DC grounding Polarisation H Plane Cable Height Weight (order separate) SG1885-TPM White fibreglass radome, aluminium mount ferrule and cable assembly GHz Full band <1.5:1 full band Factory 5.14 dbi 10 Watts Yes Vertical 360 omni-directional 3 metres RG58 low loss - side exit from ferrule TNC male fitted as standard - or specify requirements 500mm 350grams Bracket: GM1, GM2 or GM6 Spring: 1269 or 1270 Mount as high on your structure, mast or tower as possible using the appropriate minimum 13mm hole or mounting hardware with 13mm hole.

35 MD1800 & MD1950 UHF GHz Stud or magnetic base mount These Ground independent omnidirectional data link collinears are specifically designed for wireless data trasmit and receive in either a stud mount or magnetic base mount configuration., coaxial feeder cable, adaptors and other installation accessories are all available separately. MD1800B MD1800B-MGB MD1950 Black fibreglass radome, aluminium ferrule and cable assembly GHz GHz Bandwidth Full band Full band Full band VSWR <1.5:1 full band <1.5:1 full band <1.5:1 full band Tuning Factory Factory Factory Gain 2.1 dbi 2.1 dbi 2.1 dbi Impedance - nominal Maximum power 10 Watts 10 Watts 10 Watts DC grounding Yes Yes Yes Polarisation Vertical Vertical Vertical Cable 5m RG58 low loss - side exit from ferrule SMA male fitted as standard - or specify requirements Height 320mm 340mm 300mm Weight 340grams 1.05Kg 320grams (order separate) Any bracket/hole with a 13mm hole such as GM1, GM2 or GM5 Magnetic base fitted Any bracket/hole with a 13mm hole such as GM1, GM2 or GM5 Mount as high on your vehicle, structure, mast or tower as possible using the appopriate mounting bracket or magnetic base

36 Y1809-MIMO-2 M.I.M.O. 4G upper MHz Radome enclosed Yagi The Y1809-MIMO-2 mast mount enclosed Yagi is specifically designed and manufactured for directional transmit and recieve utilising Multiple In, Multiple Out (M.I.M.O.) within the 4G upper frequency range MHz. Coaxial feeder cable, connectors and other installation accessories are all available separately. Bandwidth VSWR Tuning Y1809-MIMO-2 2 x white or black radome, aluminium mount plate M.I.M.O. 4G MHz Full band <1.5:1 across full band Factory Number of elements 9 Gain Maximum power Impedance 11.3 dbi - per plane 25 Watts Polarisation Slant +45 and -45 H Plane E Plane Front-to-back ratio DC grounding Cable Length Width Weight Projected area Wind load at 160kph 36 - per plane 43 - per plane 20dB Yes 2 x N- type female fitted as standard - or specify alternate 2 x 200mm RG142 teflon cable - rear exit 345mm 87mm 2.9Kg 0.03m² 3.1Kg Aluminium mount plate, 2 x galvanised steel V-blocks, 2 x 50mm diameter galvanised steel U-bolts

37 Y2009-MIMO-2 M.I.M.O. 3G upper MHz Radome enclosed Yagi The Y2009-MIMO-2 mast mount enclosed Yagi is specifically designed and manufactured for directional transmit and recieve utilising Multiple In, Multiple Out (M.I.M.O.) within the 3G upper frequency range MHz. Coaxial feeder cable, connectors and other installation accessories are all available separately. Bandwidth VSWR Tuning Y2009-MIMO-2 2 x white or black radome, aluminium mount plate 3G MHz Full band <1.5:1 across full band Factory Number of elements 9 Gain Maximum power Impedance 11.3 dbi - per plane 25 Watts Polarisation Slant +45 and -45 H Plane E Plane Front-to-back ratio DC grounding Cable Length Width Weight Projected area Wind load at 160kph 36 - per plane 43 - per plane 20dB Yes 2 x N-type female fitted as standard - or specify alternate 2 x 200mm RG142 teflon cable 290mm 87mm 3.0Kg 0.03m² 3.1Kg Aluminium mount plate, 2 x galvanised steel V-blocks, 2 x 50mm diameter galvanised steel U-bolts

38 ZD8Z-XP-MIMO Slant polarised wireless data panel 4G LTE, 4G & 3G The ZD8Z-XP-MIMO is a slant polarised panel covering the entire Telstra, Optus & Vodafone 4G LTE, 4G & 3G (NextG ) mobile phone networks, utilising Multiple In, Multiple Out (M.I.M.O.) capability. With the panel being an enclose antenna, the radiating internals have minimal exposure to damage or moisture ingress. Coaxial feeder cable, connectors and other installation accessories are all available separately. Bandwidth ZD8Z-XP-MIMO UV protected ABS radome, aluminium back screen Telstra, Optus & Vodafone 4G LTE, 4G & 3G (NextG ) MHz & MHz Full band VSWR <2.0:1 VSWR Tuning Gain - nominal Factory 8 dbi Polarisation Slant +45 and -45 Isolation Front-to-back ratio Maximum power Impedance >25dB >23dB 50 Watts H Plane 65 E Plane 60 PIM Panel dimensions Weight 2 x N-type Female - 7/16 DIN female model available 2 x 43dBm Carrier <-140dBc 310mm x 310mm x 150mm 3.0Kg Working temperature range -40 C to + 70 C Rated Wind velocity 200km/h Mounting bracket up to diameter 80mm capability

39 ZD8Z-XP-716-MIMO Slant polarised wireless data panel 4G LTE, 4G & 3G The ZD8Z-XP-716-MIMO is a slant polarised panel covering the entire Telstra, Optus & Vodafone 4G LTE, 4G & 3G (NextG ) mobile phone networks, utilising Multiple In, Multiple Out (M.I.M.O.) capability. With the panel being an enclose antenna, the radiating internals have minimal exposure to damage or moisture ingress. Coaxial feeder cable, connectors and other installation accessories are all available separately. Bandwidth ZD8Z-XP-716-MIMO UV protected ABS radome, aluminium back screen Telstra, Optus & Vodafone 4G LTE, 4G & 3G (NextG ) MHz & MHz Full band VSWR <2.0:1 VSWR Tuning Gain - nominal Factory 8 dbi Polarisation Slant +45 and -45 Isolation Front-to-back ratio Maximum power Impedance >25dB >23dB 100 Watts H Plane 65 E Plane 60 PIM Panel dimensions Weight Working temperature range Rated wind velocity 2 x 7/16 DIN Female - N-type female model available 2 x 43dBm Carrier <-140dBc 310mm x 310mm x 150mm 3.0Kg -40 C to + 70 C 200km/h Mounting bracket up to diameter 80mm capability

40 Y1809-DECT D.E.C.T GHz Digitally Enhanced Cordless Telecommunications The Y1809-DECT is a directional point-to-point, data link mast mount Yagi, specifically designed for Digitally Enhanced Cordless Telecommunications (D.E.C.T.). Coaxial feeder cable, water-proofing, bird proofing and other installation accessories are all available separately. Bandwidth VSWR Tuning Y1809-DECT White fibreglass radome and aluminium mount plate D.E.C.T GHz Full band <1.5:1 full band Factory Number of elements 9 Gain Impedance Maximum power Polarisation 11.3 dbi 25 Watts Mount Horizontal or Vertical as required H Plane 36 E Plane 43 Front-to-back ratio DC grounding Cable Tail Dimensions Weight -20 db Yes 5 metres RG58 low loss N-type female fitted as standard - rear exit 300mm x 80mm 1.5Kg Projected area 0.015m Wind load at 160kph (supplied) 1.82Kg Aluminium mount plate, 2 x galvanised steel V-blocks, 2 x 50mm diameter galvanised steel U-bolts

41 Y1818-DECT D.E.C.T GHz Digitally Enhanced Cordless Telecommunications The Y1818-DECT is a directional point-to-point, wireless data link mast mount Yagi, specifically designed for Digitally Enhanced Cordless Telecommunications (D.E.C.T.). Coaxial feeder cable, water-proofing, bird proofing and other installation accessories are all available separately. Bandwidth VSWR Tuning Y1818-DECT White fibreglass radome and aluminium mount plate D.E.C.T GHz Full band <1.5:1 full band Factory Number of elements 18 Gain Impedance Maximum power Polarisation 15.3 dbi 25 Watts Mount Horizontal or Vertical as required H Plane 23 E Plane 26 Front-to-back ratio DC grounding Cable tail Dimensions Weight -20 db Yes 5 metres RG58 low loss - rear exit from plate N-type female fitted to cable 950mm x 80mm 2Kg Projected area 0.035m Wind load at 160kph (supplied) 4.26Kg Aluminium mount plate, 2 x galvanised steel V-blocks, 2 x 50mm diameter galvanised steel U-bolts

42 MD2400 series ISM GHz Stud mount WiFi/ISM2.4 collinear The MD2400 series of ground independent omnidirectional data link collinears are specifically designed for ISM2.4 or Wifi GHz range., coaxial feeder cable, adaptor and other installation accessories are all available separately. MD2400-B MD2400-W Colours available Black White Coloured fibreglass radome, aluminium ferrule and cable assembly ISM GHz ISM GHz Bandwidth Full band Full band VSWR <1.5:1 full band <1.5:1 full band Tuning Factory Factory Gain 2.1 dbi 2.1 dbi Impedance - nominal Maximum power 10 Watts 10 Watts DC grounding Yes Yes Polarisation Vertical Vertical Cable 5 metres RG58 low loss - side exit from ferrule SMA male fitted as standard - or specify requirements Height 230mm 230mm Weight 150grams 150 grams (order separate) Suits any bracket or hole with a diameter 16mm hole Bracket: GM1, GM2, GM4 or A-6211 Mount antenna as high as possible on your structure/ building or tower as possible ensuring no obstructions.

43 SG2400 series ISM 2.4 or WiFi Stud or flange mount collinear These omni-directional ISM2.4/WiFi band, data link collinears have models designed to be mounted either using a bracket or by flange, to suit any installation requirements., coaxial feeder cable, water-proofing, adaptors and other installation accessories are all available separately. SG2400-TPM SG2400-R White radome and aluminium ferrule White radome and grey PVC base WiFi/ ISM GHz Bandwidth Full band Full band VSWR <1.5:1 full band <1.5:1 full band Tuning Factory Factory Gain 5.14 dbi 5.14 dbi Impedance - nominal Maximum power 10 Watts 10 Watts DC grounding Yes Yes Polarisation Vertical Vertical H Plane Cable 360 omni-directional 500mm RG58 low loss - side exit or base exit TNC male fitted as standard - or specify requirements Height 550mm 380mm Weight 220grams 320grams Mounting (order separate) Using the 16mm thread Any bracket or hole with a diameter 13mm hole Bracket: GM1, GM2, GM4, GM6 or A-6211 Using the 100mm flange base Secure 100mm flange to flat surface using 2 screws

44 Z ISM2.4 or WiFi Mast mount collinear The Z is an omnidirectional mast mount collinear, designed for wireless data communications in the WiFi/ISM2.4 range., coaxial feeder cable, water-proofing, bird proofing and other installation accessories are all available separately. Z Bandwidth VSWR Tuning Gain Impedance - nominal Maximum power DC grounding Polarisation H Plane Height Weight Mount section (order separate) White fibreglass radome, stainless steel mount section and tri-metal plated termination WiFI/ ISM GHz Full band <1.5:1 full band Factory 10 dbi 50 Watts Yes Vertical 360 omni-directional N-type female in base of mount section - no cable 850mm 610grams 170mm x 25.4mm 2 x EB1-SS or 1 x UB3SS Mount as high on your structure, mast or tower as possible using the appropriate mounting clamp/s

45 Z2400-8RS WiFi or ISM GHz Rear screened collinear The Z2400-8RS is a mast mount collinear with a rear screen fitted, designed for wireless data link applications in the WiFi ISM GHz range. The rear reflector screen restricts the radiation pattern emmited at the rear of the antenna. Coaxial feeder cable, water-proofing, bird proofing and other installation accessories are all available separately. Bandwidth VSWR Tuning Gain Impedance - nominal Maximum power DC grounding Polarisation Z2400-8RS White fibreglass radome, chrome ferrule, aluminium rear reflector screen and tri-metal plated connector WiFi/ ISM GHz Full band <1.5:1 full band Factory 13 dbi - with rear screen fitted 50 Watts Yes Vertical H Plane 17 E Plane 170 Front-to-back ratio Dimensions Weight (supplied) -20 db N-type female in base of mount section - no cable 850mm x 150mm 1.25Kg 2 x 50mm diameter U-bolts and stand-offs fitted to rear screen Mount as high on your structure, mast or tower as possible using the U-Bolts and stand-offs supplied Vertical E-Plane Radiation Pattern at 2.4 GHz

46 DLD2400 WiFi or ISM 2.4GHz Stud mount data link dipole The DLD2400 is a stud mount dipole specifically designed for 2.4GHz ISM or WiFi band. The small profile of this antenna allows for it to covertly be installed with minimal visual impact., coaxial feeder cable, adaptors and other installation accessories are all available separately. DLD2400 Black PVC radome and black delrin mount ferrule WiFi/ ISM 2.4GHz VSWR <1.5:1 Tuning Gain Impedance - nominal Maximum power DC grounding Polarisation H Plane Cable Height Weight (order separate) Factory 2.1 dbi 20 Watts Yes Vertical 360 omni-directional 600mm RG174 (bottom exit) SMA male fitted as standard - or specify requirements 115mm 40grams Any hole or bracket with a minimum diameter 12.7mm hole such as GM1, GM2 or GM6 Mount as high on your structure, pole or mast as possible using the appropriate mounting brackets. Do not mount near any vertical metallic objects.

47 WH2400 series WiFi/WLAN or ISM 2.4 Interior data link whip The WH2400 series are specifically designed for internal use on low power data link devices operating in the WiFi/WLAN ISM 2.4 or ISM5.8 range. The WH2400 series suit any device with a protruding SMA female connector. The small profile of this antenna allows for it to covertly be installed with minimal visual impact. Coaxial feeder cable, adaptors and other installation accessories are all available separately. WH WH R WH Black UV resistant PVC and brass ISM2.4/WiFi/WLAN 2.4GHz ISM5.8/WiFi/WLAN 5.8GHz WiFi/WLAN GHz VSWR <1.5:1 <1.5:1 <1.5:1 Tuning Factory Factory Factory Gain 2.1 dbi 2.1 dbi 2.1 dbi Polarisation Vertical Vertical Vertical Maximum power 5 Watts 5 Watts 5 Watts Impedance - nominal SMA male as base SMA male as base SMA male as base Height 70mm 73mm 85mm Weight 9grams 9grams 15grams WH WH Mounting Onto any device or cable with SMA female termination Mount as high on your device or hand-held device as possible, if mounting inside structure ensure no metallic obstructions impede signal path.

48 ZAW-WiFi-4S WiFi or ISM2.4GHz Low profile antenna The ZAW-WiFi-4S is designed and manufactred for WiFi or ISM2.4 communications all within a low profile radome. The ZAW-WiFi-4S incorporates an internal PCB design to achieve a low profile. Suitable for portable ATM s or meter boxes or any situation where a low profile is required. Adaptors, connectors, patch leads and other installation accessories are all available separately. Bandwidth Peak Gain Polarisation VSWR Impedance Power supply Cable Dimensions Weight Operating temperature Storage temperature (supplied) ZAW-WiFi-4S Black ABS radome, adhesive base and cable assembly WiFi or ISM GHz Full band 0 dbi Linear <2.0:1 across bandwidth 50 Ohm Power handling capacity: 10 Watts Fakra pastel green 6019 type fitted as standard 3.0m RG174A/U Diameter: 64.5mm, Height: 15mm 80grams -40 C to +85 C -45 C to +90 C Remove the adhesion cover from the base and adhere the antenna where required.

49 Data CP WiFi or ISM GHz End fire helical right-hand circular collinear The CP is a directional right-hand circular polarised, end fired helical collinear specifically designed for point-to-point data communications within the ISM GHz range. A helically wound right-hand circulary polarised antenna will reduce unwanted signal interference and reflections.the end fired design is particularly well suited for point-to-point data communications (cordless phone, WiFi or wireless broadband)., coaxial feeder cable, adaptors and other installation accessories are all available separately. Bandwidth VSWR Tuning Gain Polarisation Circularity Impedance - nominal Maximum power CP White fibreglass radome, stainless steel mount section and tri-metal plated termination WiFi or ISM GHz Full band <1.5:1 full band Factory 17.1 dbi Right-hand circular <2 db 50 Watts H-Plane H Plane 17 E Plane 19 Front-to-back ratio DC grounding Length Weight Mount section (order separate) 15 db Yes N-type female in rear of mount section - fitted as standard 1.12 metres 1.5Kg 220mm x 50mm Mast/pole mounting: 1 x UB2-SS or 1 x RB8 Side/Wall mounting: 1 x NSM-223 E-Plane

50 Y2400 Series WiFi or ISM GHz Point-to-point enclosed Yagi These radome enclosed Yagi s are specifically designed for directional point-to-point WiFi or ISM GHz wireless data link transmit and receive applications. The enclosed design ensures protection from damage or water ingression, increasing the service life of these antennas. Coaxial feeder cable, water-proofing, bird proofing, adaptors and other installation accessories are all available separately. Y Y VSWR White or Black radome and aluminium mount plate WiFi or ISM GHz <1.5:1 Full band Tuning Factory Factory Number of elements 9 18 Gain 11.3 dbi 17.8 dbi Maximum power 25 Watts 25 Watts Impedance Polarisation Mount Horizontal or Vertical as required H Plane E Plane Front-to-back ratio -20 db -20 db DC grounding Yes Yes Cable 200mm RG58 low loss - rear exit from mount plate N-type female fitted to cable - as standard Dimensions 300mm x 80mm 700mm x 80mm Weight 1.5Kg 2Kg Projected area 0.015m 0.035m Wind load at 160kph 1.82Kg 4.26Kg (supplied) Aluminium mount plate, 2 x galvanised steel V-blocks and 2 x 50mm diameter galvanised steel U-bolts

51 PD-240N2 WiFi/WiMAX or ISM GHz 2-way power divider The PD-240N2 is a power divider for combining or splitting the output/input of two WiMAX data link antennas operating within the GHz freqency range. The PD-240N2 has the ability to be installed either inside a structure or outside, ensure appropriate weather-proofing is applied to maintain the service life of the PD-240N2. Cable assemblies, water-proofing, adaptors and other installation accessories are all available separately. Bandwidth Tuning VSWR Impedance Maximum power Input connector Output connectors Dimensions Weight (supplied) Mounting recommendations PD-240N2 Aluminium body, mount plate and tri-metal plated terminations WiFi/ WiMAX GHz Full band Factory <1.2:1 across full band 250 Watts N-type female 2 x N-type females Length: 80mm, Width: 50mm 200grams Mount using the mount bracket connected to the power divider, using 1 x 6mm hole Once all of the terminations are fitted, cover all terminations with one layer of amalgamation tape followed by a layer of PVC tape, to reduce water ingression.

52 ZCG-EEH-201 Fixed cable low profile antenna WiFi GHz & GHz The ZCG-EEH-201 fixed cable low profile antenna will improve WiFi coverage reception and transmission range. Being an enclosed unit, the internals are weatherproofed to IP67 to ensure a long service life. Unique specifications for the ZCG-EEH-201 are: - WiFi data communication - Dual band at both 2.4 and 5.8GHz - Rugged design - Ground independent Adaptors, coaxial cable, connectors and other installation accessories are all available separately. Bandwidth VSWR Tuning Gain Maximum power Impedance Polarisation Cable Operating temperature Storage temperature Dimensions Weight Waterproof rating ZCG-EEH-201 Black ASA radome, chrome fittings and cable assembly WiFi GHz and GHz Dual band <2.0:1 across full bands Factory 4.0dBi peak 5 Watts Linear, Vertical 3m x RG58 bottom exit - or specify length requirements SMA(SP) fitted as standard - or specify requirements -40 C to +80 C -40 C to +85 C Diameter: 41.5mm, Height: 78.4mm 85grams 10.5mm mounting thread, rubber gasket, washer and nut (supplied) IP67

53 GCT-2.4 Low Profile WiFi Antenna GHz The GCT-2.4 is specifically designed and manufactured for WiFi 2.4GHz improvment either vehicle mounted or fixed position. The design of this antenna is compact and low profile for situations where damage or vandalism can occur. Alternative mounting options, adaptors, connectors and other installation accessories are all available separately. GCT-2.4 Cream polycarbonate radome and mount base, rubber gasket and polycarbonate mount nut WiFi GHz VSWR <2:1 Tuning H Plane Impedance Maximum power Cable Dimensions Weight Factory 360 omni-directional 25 Watts 5 metres RG174/U SMA male fitted as standard or specify requirements 100mm diameter x 39mm tall 280grams Any bracket or flat surface with 20mm hole using cream ABS nut supplied. As high on your vehicle/structure as possible using appropriate bracket/hole, can be inverted mounted from a ceiling. Updated 18th January 2016

54 Z & Z GHz Mast mount collinear The Z and Z are omni-directional mast mount collinears designed for wireless data communications within GHz or GHz., coaxial feeder cable, water-proofing, bird proofing and other installation accessories are all available separately. Z Z White radome and stainless steel mount section GHz GHz Bandwidth Full band Full band VSWR <1.5:1 full band <1.5:1 full band Tuning Factory Factory Gain 10 dbi 10 dbi Impedance - nominal Maximum power 50 Watts 50 Watts DC grounding Yes Yes Polarisation Vertical Vertical H Plane 360 omni-directional N-type female in base of mount section - as standard Height 820mm 810mm Weight 600grams 590grams Mount section 240mm x 25.4mm 240mm x 25.4mm (order separate) 2 x EB1-SS or 1 x UB3-SS Mount as high on your structure, mast or tower as possible using the appropriate mounting clamps. Ensure the antenna is mounted away from any vertical metallic objects

55 Y2650 Series 2.65GHz Point-to-point enclosed Yagi The Y2650 series of mast mount Yagi s are specifically designed for directional point-to-point 2.65 wireless data transmit and receive applications. The enclosed design ensures protection from damage or water ingression, increasing the service life of these antennas. Coaxial feeder cable, water-proofing, bird proofing, adaptors and other installation accessories are all available separately. Y Y White fibreglass radome and aluminium mount plate 2.65GHz 2.65GHz VSWR <1.5:1 VSWR Tuning Factory Factory Number of elements 9 18 Gain 11.3 dbi 17.8 dbi Maximum power 25 Watts 25 Watts Impedance Polarisation Mount Horizontal or Vertical as required H Plane E Plane Front-to-back ratio -20 db -20 db DC grounding Yes Yes Cable 200mm RG58 low loss - rear exit from plate N-type female fitted to cable - as standard Dimensions 300mm x 80mm 700mm x 80mm Weight 1.5Kg 2Kg Projected area 0.015m 0.035m Wind load at 160kph 1.82Kg 4.26Kg (supplied) Aluminium mount plate, 2 x galvanised steel V-blocks and 2 x 50mm diameter galvanised steel U-bolts

56 Z NF GHz Omni-directional collinear The Z NF is an omni-directional mast mount collinear, designed and manufuctured for wireless data communications in the GHz frequency range., coaxial feeder cable, connectors and other installation accessories are all available separately. Bandwidth VSWR Tuning Gain Maximum power Impedance - nominal DC grounding Polarisation H Plane Height Weight Mounting (order separate) Z NF White fibreglass radome, chrome mount ferrule and aluminium mount adaptor GHz Full band <1.5:1 across full band Factory 10 dbi 50 Watts Yes Vertical 360 omni-directional N-type female in base of ferrule 780mm 500grams Detachable aluminium mount adaptor - supplied 2 x EB1-SS or 1 x UB3-SS Mount as high as possible on your structure, tower or mast using the appropriate mounting clamps. Connect cable then insert the antenna ferrule into the mount adaptor until secure.

57 DLD GHz Stud Mount Data Link Dipole The DLD3500 is a stud mount dipole specifically designed for 3.5GHz wireless data applications. Suitable for either interior to exterior use. Exterior use will require water-proofing applied to terminations., coaxial feeder cable, adaptors and other installation accessories are all available separately. DLD3500 Black PVC radome, black delrin mount ferrule, stainless steel securing nut and external cable 3.5GHz VSWR <1.5:1 Tuning Gain Impedance - nominal Maximum power DC grounding Polarisation H Plane Cable Height Weight (order separate) Factory 2.1 dbi 20 Watts Yes Vertical 360 omnidirectional 560mm RG174 - bottom exit from ferrule SMA male fitted as standard or specify requirements 95mm 35 grams Any bracket or hole with a diameter 12.7mm hole Bracket: GM1, GM2 or GM6 Mount as high on your structure, pole or mast as possible using the appropriate mounting brackets. Do not mount near any vertical metallic objects. If interior mounting, ensure antenna has minimal obstructions by metallic objects/surfaces or walls Updated 8th November 2018

58 CP ISM GHz End fire right-hand circular helical Yagi The CP is a directional right-hand circular polarised, end fired helical antenna specifically designed for point-to-point data communications within the ISM 5.8 range.a helically wound righthand circulary polarised antenna will reduce unwanted signal interference and reflections. The End Fired design is particularly well suited for point-to-point data communications (cordless phone, WiFi or wireless broadband)., coaxial feeder cable, adaptors and other installation accessories are all available separately. Bandwidth VSWR Tuning Gain Polarisation Circularity Impedance - nominal Maximum power CP White fibreglass radome, aluminium mount plate and cable assembly ISM GHz Full band <1.5:1 full band Factory 14 dbi Right-hand circular <2 db 100 Watts H Plane 18 E Plane 20 Front-to-back ratio DC grounding Cable Length Weight Projected area Wind load at 160kph 20 db Yes 200mm RG142 - rear exits from base of plate N-type female fitted as standard - or specify requirements 180mm 500grams 0.008m² 0.909Kg, 0.009kN 1 x 50mm diameter U-bolts and V-blocks (supplied)

59 Z5600 Omni-directional wireless data collinear GHz The Z5600 is an omni-directional mast mount collinear, designed and manufuctured for the telemetry monitoring or wireless data transfer within the GHz frequency range., coaxial feeder cable, adaptors and other installation accessories are all available separately. Bandwidth Z5600 Black fibreglass radome, aluminium mount section and tri-metal plated connectors GHz Full Band VSWR <1.5:1 Tuning Gain Maximum Power Impedance - nominal DC grounding Polarisation H Plane Factory 5.2 dbi 10 Watts Yes Vertical 360 omni-directional E Plane 73 Height Weight Mount section (order separate) N-type female in base of mount section - no cable 250mm 100grams 100mm x 20mm Mast mounting: 1 x EB1-SS or 1 x UB3-SS Side/wall mounting: 2 x NSM-B20M Mount as high on your structure, pole, mast or tower as possible using the appropriate mounting clamp

60 Z5800 ISM GHz Omni-directional collinear The Z5800 is an omnidirectional mast mount collinear, designed and manufuctured for the ISM GHz frequency range. Coaxial feeder cable, adaptors, bird-proofing and other installation accessories are all available separately. Z Z Bandwidth Black fibreglass radome, chrome mount ferrule and aluminium mount bracket ISM GHz - Centre frequency 5.8GHz Full band - 200MHz VSWR <1.5:1 <1.5:1 Tuning Factory Factory Gain 8 dbi 10 dbi Maximum power 50 Watts 50 Watts Impedance - nominal DC grounding Yes Yes Polarisation Vertical Vertical H Plane 360 omni-directional E Plane N-type female in base of mount ferrule - no cable Height 575mm 675mm Weight 350grams 500grams (supplied) 90 degree bracket and 50mm diameter U-bolt Mount as high on your structure, pole, mast or tower as possible using the attached mounting clamp

61 Accessories Stainless steel & black nylon cable ties Page 1 of 2 Cable ties, either stainless steel or black nylon are a crucial component for any antenna installation. PVC tape, amalgamation tape, grommets and other installation accessories are all available separately. Stainless Steel Order Code 8117 Bag of 100, 316 Grade, 360mm long x 4.6mm Bag of 100, 316 grade, 200mm long x 4.6mm Bag of 100, 316 grade, 450mm long x 4.6mm Bag of 100, 316 grade, 600mm long x 4.6mm 8125 Stainless steel cable tie tensioner required to tighten stainless steel cable ties. Fits cable ties quick, easy and neat. Black Nylon Order Code Bag of 100, 100mm long 8529 Bag of 100, 200mm long 8530 Bag of 100, 300mm long

62 Accessories Water-proofing Page 2 of 2 Water-proofing is an crucial step in any antenna installation whether it s a vehicle mount, marine, fixed position or broadcast, correct water-proofing can lengthen the life of your antenna system Consult ZCG s installation guides or ZCG s sales team for advice on correct water-proofing for your requirements. Order Codes PVC electrical insulating tape, black, 19mm wide x 0.18mm thick, 20 metre roll Self-bonding amalgamating electrical tape, 19mm wide x 0.76mm thick, 9.15m roll 8574 Cable Gland Order Code 8485 Black PVC, 5-10mm capability Black PVC, 11-17mm capability Cream PVC, 5-10mm capability Cream PVC, 18-24mm capability Black PVC, suitable for 7/8 cable Cable Grommet Order Code 5591 Bag 100, Nitrile grommet for RG Single Nitrile grommet for RG58