SKF Multilog On-line System DMx
|
|
- Jasmine Eaton
- 5 years ago
- Views:
Transcription
1 SKF Multilog On-line System DMx CMMA 9910/CMMA 9920 Universal distributed vibration monitor The SKF Multilog On-line System DMx provides distributed vibration based machinery protection and condition monitoring in a single device, for use in both conventional and hazardous areas. Four channels Intrinsically safe Integral eddy current probe drivers Reduced installation costs SKF Reliability Systems class leaders in condition monitoring, have joined forces with intrinsic safety experts Pepperl+Fuchs to develop the SKF Multilog On-line System DMx. The SKF Multilog DMx offers a four channel vibration monitoring solution that for the first time allows the requirements of critical machinery monitoring, from transducer to dynamic data processing, to be fulfilled by an intrinsically safe device located on the machine skid. Protection and condition monitoring The SKF Multilog DMx provides two distinct vibration monitoring capabilities in the same module: Intrinsic safety The complexity of vibration measurements has previously forced the monitoring electronics into the safe area. The SKF Multilog DMx takes the step into the Zone 1 hazardous area. This breakthrough allows the benefits of distributed modularity enjoyed by process IO and transmitter systems to be extended to fully featured vibration monitoring. The low power consumption requirements of intrinsically safe devices also provide energy savings when compared to control room monitor racks. Reliability A reliable machine shutdown command is a prerequisite, and the SKF Multilog DMx offers Functional Safety compliant PFD data to IEC (SIL levels). Machine protection measurements to react to a vibration alarm that may signify a looming catastrophic failure, in compliance with the API 670 standard. Condition monitoring measurements to be used by sophisticated software to predict a potential catastrophic failure.
2 Features Digital technology processing When compared to the traditional control room architecture, distributing modular vibration monitors at each machine across the plant provides cost savings from: Combined machine protection and analysis capabilities Typical applications are for vibration, thrust, or pressure monitoring (any engineering units possible) Vector data. Up to four user programmable amplitude and phase vectors per channel Overall level data Dynamic data FFT and time waveform Steady-state and transient machine operation All configuration data is held on board the module, no pre-knowledge or database look-up required Multi-configuration storage capability advantageous to OEMs Configuration data is stored in non-volatile memory and restored on power-up Sophisticated and flexible alarming capability, any logical combination of measurements allowed Multiple LEDs for local indication of module, channel and alarm status, and diagnostic data Integrated self test and calibration features, potentiometer free. Storage of individual names/tags for channels, alarms, tachometer, and configuration sets Modularity and configurability Transducer systems The selection and configuration of the vibration monitor stays in the scope of the machine package, without need to interface at a sensor level with instrumentation outside that package. On-board digital eddy current probe drivers, which can be configured to accommodate a range of probe types, cable lengths, and target materials Built-in barriers for direct connection to Zone 0 mounted sensors [ia] IIC Universal inputs: dynamic and position measurements (any combination) within the same module Fully configurable for any engineering units, transducer sensitivity, or any filter cut-off frequencies Independent transducer power supply circuits for each channel Reduced installation costs Field cabling The many multi-pair cables carrying analogue signals between machine and control/instrument room are replaced with single or dualpair communications cables carrying digital data. A significant reduction in copper costs is realized. Instrument room space Costly cabinets can be eliminated. Semi-populated 19 monitor racks are no longer required to achieve safety system segregation. Installation man-hours Physical loop-checking of many hundreds of sensor points on a plant can be reduced to a few data link chains, saving significant man-hours for the machine manufacturer, LSTK contractor, and the end user maintenance team. 2 Communications Dual redundant, intrinsically safe, RS 485 links Both links support transfer of any data type: status, level, analysis data, or configuration Single master, multiple slave protocol with message CRC Fast messaging scheme for shutdown commands, dynamic module control, and data acquisition Duplicate terminals for serial communications and transducer inputs to ease wiring congestion
3 SKF Distributed system advantage New technology reduces installation costs without compromising functionality. API 670 Style 19" Rack-Mount System Architecture Sensor Barrier Digital processing within a vibration monitor located on the machine skid significantly reduces field wiring. Monitor Sensor Conventional Driver Hazardous area Safe area Field mounted, distributed monitors reduce costly control room cabinets and rack hardware. SKF Multilog DMx System Architecture Sensor NEW Barrier DMx monitors with integral safety circuits almost eliminate traditional barriers. Sensor Driver and monitor Hazardous area Safe area Easy connection to plant control and information networks by common protocols. Universal vibration monitor protection and condition monitoring in a single device, for use in both conventional and hazardous areas. 3
4 Technical specifications Inputs Sensors: Four channels dynamic Sensor types: Inputs from, and power to, two-wire or three-wire accelerometers, velocity transducers or eddy current probe systems. Integral driver circuits for directly connected eddy current probes. Sensor power: 3,3 or 14 ma constant current, +20 V constant voltage at up to 14 ma Logic input: Single logic TTL level input for ta- chometer input or tachometer cascade from another SKF Multilog DMx module Tachometer input: Analog tachometer input (range 0 to +5 V) with programmable threshold level Keyway phase reference input: Two internal eddy current probe drivers on dynamic inputs may be routed to tachometer processing, with programmble thresholds Data acquisition and evaluation General Sampling: Parallel A/D conversion, digital signal processing, on-board clock calendar Input frequency range: DC to 20 khz Vibration acceleration, velocity and displacement: Fully programmable AC and DC measurement units and sensitivities SKF Acceleration Enveloping: Filter 1: 5 to 100 Hz Filter 2: 50 to Hz Filter 3: 500 to Hz Detection types: True RMS, peak, Peak-to-Peak, and rectified average signal assessments are concurrently available Axial thrust and process variables: Fully program- mable DC measurement units and sensitivities Application specific measurements: Eccentricity, absolute shaft vibration, Smax, differential expansion, rotor acceleration (RPM/minute), and peak speed for Turbine Supervisory Instrumentation. Rod drop (untriggered and triggered) for reciprocating compressors. Speed: Two tachometer processing channels, sourced from analog speed sensor, or internal eddy current probe driver circuit, calculating actual, and factored machine speed. One event per revolution target is required for vector data. Maximum event rate is pulses per minute. Filter ranges: Low pass and high pass filters (with two level integration if required) are implemented digitally Accuracy: ±1% excluding transducer circuit Outputs Communications link: Independent and isolated dual high speed RS 485 links Communication speed: Up to 125 kbaud (1.5 Mb/s capable) Digital output: Five opto-isolated outputs for local alarm, shutdown or tachometer cascade between modules Machinery protection Response to alarm condition: <100 ms in typical applications Alarm delay: Programmable 0 to 15 seconds, pre- or post-voting Alarms: High, low, in window, out of window for any measurement Alarm voting: Configurable voting in any logical combination of any measurement. Result transferred by communications link and opto-isolated output. Transducer OK: Frequency monitoring provides enhanced OK detection, in addition to regular DC gap voltage monitoring, for directly connected eddy current probes. Bias voltage check for standard eddy current probe systems and accelerometers. Trip multiply: User definable factors independent for each alarm parameter activated by communications link Danger bypass: Activated by communications link Local indication: LEDs on module; 4x Tx OK, 5x alarm, 1x power, 1x module run, 1x module status Condition monitoring FFT and time data: Continuous and separate sig- nal analysis paths for point time waveforms, and 800-line FFT for all channels Frequency band monitoring: Four independent, configurable bands for each FFT all with their band RMS, maximum line and frequency values Vector data: Four user definable n.nx amplitude and phase vectors per channel (e.g. 1x, 2x, 0.4x, 7x) for monitoring or balancing. Transient data acquisition: Data capture triggered on transient window low, transient window high, RPM, time or RPM + time Power requirements Operating voltage: 8,6 to 9,5 V supplied by an In- trinsically Safe power supply Power consumption: 4 W typical Physical Two part system: Module consists of a removable processing unit and a terminal base mounted on DIN-rail Dimensions: Height: 156 mm (6.14 in.) Width: 104 mm (4.09 in.) Depth: 116 mm (4.57 in.) Weight: 0,5 kg (1.1 lb.) maximum Mounting information: See Figure 1 for DIN-rail mount Enclosure requirements: Minimum IP 20 for II 2 (1) G ib [ia] IIC T4 and II (1D) [ iad] Minimum IP 54 for I M2 (M1) ib [ia] I Hot swappable: Yes. Processing unit hot swappable on terminal base without disturbance to wiring. Environmental Hazardous area: ATEX approved IEC approved culus approved EMC: EMC tested to EN 61326, EN and NAMUR NE21 Compliance: CE mark compliant, conforms to 94/9/EC ATEX Directive and to 89/336/EG EMC Directive Operating temperature range: 20 to +65 C ( 4 to +149 F) Storage temperature range: 20 to +100 C ( 4 to +212 F) Humidity: 93% relative humidity, non-condensing Shock resistance: 15 g peak for 11 ms Vibration resistance: 1 g, 10 to 150 Hz to IEC Network SKF software interfaces for: Configuration and data display software Condition monitoring and plant asset manage- ment software Decision support software Common control protocols 116 mm (4.57 in.) 104 mm (4.09 in.) 156 mm (6.14 in.) Figure 1. SKF Multilog DMx module dimensions. 4
5 Electrical data BVS 07 ATEX E 075 X ATEX directive group/category Gas: II 2(1)G ib[ia] IIC T4 Mining: I M2(M1) ib[ia] I Dust: II (1D) [ iad] Up to 31 modules RS 485 #1 RS 485 isolator(s) RS 485 #2 IEC BVS X [Zone 0] ib[ia] IIC T4 ib[ia] I [ iad] culus IS Process control equipment for use in Hazardous Locations, CL I, GP ABCD; CL II, GP EFG; CL III; CL I, Zone 1, A ib[ia] IIC; ib[ia] IIC, T4. Providing IS circuits when installed per control drawing number Associated Equipment [ ia] Appareillage Connexe. Area Zone 1 or Zone W X 4 Power supply ample SKF Multilog DMx schematic. 8-channel installation. Apparatus supply and input/output parameters CMMA 9910 and CMMA 9920 Power supply (V+, V-) Connection 33 and 46 [+] Maximum values per channel 49 and 62 [ ] RS 485 (channel 1 and channel 2) 1: 34, 36, 47, 50, 52 and 63 2: 35, 37, 48, 51, 53 and 64 Tacho input Logic input Opto output (channel 1 to channel 5) 38, 54 39, 55 1: 41, 57 2: 42, 58 3: 43, 59 4: 44, 60 5: 45, 61 Voltage U i 9.5 V 4.2 V 5.4 V 5.4 V 15.0 V Voltage U o V 5.4 V 5.4 V Current I i 1 A ma Current I o ma 3 ma 2 ma Power P i 9.5 W mw Power P o mw 4 mw 3 mw Characteristic linear linear linear Internal capacitance C i 120 nf negligible negligible negligible negligible Internal inductance L i negligible negligible negligible negligible negligible Type of protection ib IIC ib IIB ia I ia IIC ia IIB ia I ternal capacitance C o [µf] ternal inductance L o [mh] L o / R o [mh / Ω] ia IIC ia IIB ia I ia IIC ia IIB ia I ia IIC ia IIB RS 485 2A RS 485 2B RS 485 1A RS 485 1B Power Power + Multi-drop configuration, dual RS 485 communications and power. 5
6 Electrical data Apparatus supply and input/output parameters CMMA 9910 Only Eddy Current Probe (ECP) input (channel 1 to channel 4) Two (2) wire input (channel 1 to channel 4) Connection s Terminals 1, 2, 17, 18 5, 6, 21, 22 9, 10, 25, 26 13, 14, 29, 30 (3) 19, 20 (7) 23, 24 (11) 27, 28 (15) 31, 32 Coax ECP1 ECP2 ECP3 ECP Maximum values per channel Voltage U i 5.4 V 28.0 V Voltage U o 5.4 V 5.4 V Current I i Current I o 16.3 ma negligible Power P i Power P o 22 mw negligible Characteristic linear linear Internal capacitance C i 200 nf negligible Internal inductance L i negligible negligible Type of protection ia IIC ia IIB ia I ia IIC ia IIB ia I ternal capacitance C o [µf] ternal inductance L o [mh] L o / R o [mh / Ω] Eddy Current Probe CMSS A a = signal + (white) b = signal (black) Eddy Current Probe using internal digital drivers. Self-generating sensor (e.g. velocity pickup). 6
7 Electrical data Apparatus supply and input/output parameters CMMA 9920 Only Eddy Current Probe (ECP) input (channel 3 to channel 4) Transducer input, two (2) wire input (channel 1 to channel 4) Transducer input, three (3) wire input (channel 1 to channel 4) Connection s Terminals 9, 10, 25, 26 13, 14, 29, 30 (3) 19, 20 (7) 23, 24 (11) 27, 28 (15) 31, 32 4, (3) 19, 20 8, (7) 23, 24 12, (11) 27, 28 16, (15) 31, 32 Coax ECP3 ECP Maximum values per channel Voltage U i 5.4 V 28.0 V 28.0 V Voltage U o 5.4 V 5.4 V 26.5 V Current I i Current I o 16.3 ma negligible 90.9 ma Power P i Power P o 22 mw negligible 432 mw Characteristic linear linear linear Internal capacitance C i 200 nf negligible negligible Internal inductance L i negligible negligible negligible Type of protection ia IIC ia IIB ia I ia IIC ia IIB ia I ia IIC ia IIB ia I ternal capacitance C o [µf] ternal inductance L o [mh] L o / R o [mh / Ω] Eddy Current Probe CMSS A a = signal + (white) b = signal (black) Shielded twisted triad cable e.g. Belden 8771 CMSS 668P-16-9 Piezoelectric accelerometer (2-wire ICP type). Eddy Current Probes using external drivers (e.g. API 670). 7
8 Configuration and data display software (CMSW 6200-EN) SKF Multilog DMx Manager software provides comprehensive transducer, data processing and alarm configuration in a user friendly interface. The software also provides live display of scalar value, timewaveform, FFT and orbit data from SKF Multilog DMx module monitor channels. For more comprehensive condition monitoring and analysis needs an interface into SKF Monitoring Suite is available. Ordering information CMMA 9910 Four (4) channel intrinsically safe SKF Multilog DMx module with 4x internal digital Eddy Current Probe drivers, 2x tacho input. No transducer power. ib IIC. CMMA 9920 Four (4) channel intrinsically safe SKF Multilog DMx module with 2x internal digital Eddy Current Probe drivers, 2x tacho input. With transducer power. ib IIC. CMSW 6200-EN SKF Multilog DMx Manager: Software for configuration and live display. Please contact: SKF Reliability Systems SKF Condition Monitoring Center San Diego 5271 Viewridge Court San Diego, California USA Tel: Fax: Kelvinbaan 16, 3439 MT Nieuwegein, The Netherlands Tel: +31 (0) Fax: +31 (0) Web: and Multilog are registered trademarks of the SKF Group. All other trademarks are the property of their respective owners. SKF Group 2009 The contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless prior written permission is granted. Every care has been taken to ensure the accuracy of the information contained in this publication but no liability can be accepted for any loss or damage whether direct, indirect or consequential arising out of the use of the information contained herein. SKF Patents include: #US #US #US #US #US #US #US #US #US #US #US #US #US6,789,025 #US6,792,360 US 5,633,811 US 5,870,699 #WO_03_048714A1 PUB CM2324 EN November 2009
SKF Multilog On-line System DMx
SKF Multilog On-line System DMx CMMA 9910/CMMA 9920 Universal distributed vibration monitor The SKF Multilog On-line System DMx provides distributed vibration based machinery protection and condition monitoring
More informationEnhanced API 670 monitoring of gearboxes
Application Note Enhanced API 670 monitoring of gearboxes Use of SKF acceleration enveloping with the On-line System DMx By Chris James SKF Reliability Systems and Oscar van Dijk SKF Reliability Systems
More informationRamp differential expansion measurements with the SKF Multilog On-line System DMx
Application Note Ramp differential expansion measurements with the SKF Multilog On-line System DMx By Marcel de Boer SKF Reliability Systems As described in the differential expansion application note,
More informationSpeed and Key Monitor Specifications
Speed and Key Monitor Specifications The Speed and Key Monitor is designed for high reliability for the plant s most critical rotating machinery monitoring speed, phase, zero speed and direction of rotation.
More informationShaft Absolute Vibration Monitor Specifications
Shaft Absolute Vibration Monitor Specifications The Shaft Absolute Vibration Monitor is designed for high reliability for the plant s most critical rotating machinery. This 1-slot monitor is used together
More informationA6500-UM Universal Measurement Card
Specifications Sheet A6500-UM Universal Measurement Card The A6500-UM Universal Measurement Card is a component of the CSI 6500 ATG machinery protection system. The card is equipped with 2 sensor input
More informationAnalog Universal Module HART for Zone 2 Series 9468/33
> 8 channels can be adjusted individually as analog inputs or outputs > Intrinsically safe inputs/outputs Ex ia > For 0/4 20 ma + HART signals > Line fault monitoring per channel > Diagnostics based on
More informationIsolators A3/1. Vibration Transducer Supply Unit Series
> For vibration, acceleration and speed sensors in 2- and 3-wire design > Space-saving dual-channel version > Signal frequencies up to 50 khz > Easy setting by means of front-side rotary switch > Galvanic
More informationTemperature Input Module for Zone 1 Series 9482/32
www.stahl.de > 8 channels for temperature sensors > Intrinsically safe inputs Ex ia > For Pt-, Ni- and Cu-resistance temperature detectors according to DIN, IEC and GOST in 2-, 3- and 4-wire circuits >
More informationDeltaV SIS Logic Solver
DeltaV SIS Process Safety System Product Data Sheet September 2017 DeltaV SIS Logic Solver World s first smart SIS Logic Solver Integrated, yet separate from the control system Easy compliance with IEC
More informationAnalog Input Module HART Ex i / I.S. Inputs, Channels Type 9461/
> 4 channels for 2-wire HART transmitters and 4 channels for 4-wire HART transmitters > Intrinsically safe inputs Ex ia IIC > Galvanic separation between inputs and system > Open-circuit and short-circuit
More informationCreate SKF Multilog On-line System IMx Transient Groups for Run up and Coast down Data Collection in Observer
Application Note Create SKF Multilog On-line System IMx Transient Groups for Run up and Coast down Data Collection in SKF @ptitude Observer Introduction In vibration analysis, we consider a transient as
More informationDigital temperature transmitter for resistance sensors Model T15.H, head mounting version Model T15.R, rail mounting version
Temperature Digital temperature transmitter for resistance sensors Model T15.H, head mounting version Model T15.R, rail mounting version WIKA data sheet TE 15.01 for further approvals see page 10 Applications
More informationDigital Input Module 24 V Ex n Inputs, 16 Channels Series 9471
> 16 channels for active 0 / 24 V signals > Zone 2 / Division 2 version for connection of circuits acc. to Ex nl, Ex na, Nonincendive and Non-Ex > Galvanic separation between inputs and system > Two channels
More informationDetection of the Rotational Direction of a Shaft in Observer 9.1
Application Note Detection of the Rotational Direction of a Shaft in SKF @ptitude Observer 9.1 Introduction In some applications, it is important to control data collection with respect to the direction
More informationDigital Input Output Module for Zone 2 Series 9470/33
www.stahl.de > 16 channels can be adjusted in pairs as digital input or output > Intrinsically safe inputs/outputs Ex ia > For contacts, NAMUR proximity switches and low-power solenoid valves > Up to 8
More informationSTT 3000 Series STT170 SMART TEMPERATURE TRANSMITTER Models STT171, STT173, STT17H, STT17F, STT17C
STT 3000 Series STT170 SMART TEMPERATURE TRANSMITTER Models STT171, STT173, STT17H, STT17F, STT17C 34-TT-03-07 3/06 PRODUCT SPECIFICATION SHEET OVERVIEW The Honeywell STT170 series of programmable temperature
More informationAS-1250FE Datasheet Dynamic Signal Acquisition Front-End for Rotating Machinery Monitoring and Analysis
Dynamic Signal Acquisition Front-End for Rotating Machinery Monitoring and Analysis HIGH PERFORMANCE ACQUISITION The AS-1250FE is a high performance, compact and flexible data acquisition hardware platform
More informationDigital Input Module NAMUR Ex i / I.S. Inputs, 16 Channels for Zone 1 / Div. 1 Series 9470/22
www.stahl.de > 16 channels for contacts and NAMUR proximity switches (EN 60947-5-6) > Intrinsically safe inputs Ex ia IIC > Galvanic separation between inputs and system > Open-circuit and short-circuit
More informationXM Monitoring Modules Specifications
Technical Data XM Monitoring Modules Specifications Catalog Numbers 1440 series The XM series of intelligent I/O modules process, in real-time, the critical parameters used to assess the current health
More informationDigital temperature transmitter Model T15.H, head mounting version Model T15.R, rail mounting version
Electrical temperature measurement Digital temperature transmitter Model T15.H, head mounting version Model T15.R, rail mounting version WIKA data sheet TE 15.01 Applications Process industry Machine building
More informationDigital Input Output Module 24 V for Ex n Zone 2 Series 9472/35
www.stahl.de > 16 channels can be adjusted in pairs as digital inputs or outputs > Suitable for NAMUR proximity switches, 3-wire PNP proximity switches, contacts and solenoid valves (24 V / 0.5 A). > Up
More informationIsolators A3/1. Transmitter Supply Unit Field Circuit Ex i Series
Transmitter Supply Unit Series 9160 > Intrinsically safe input [Ex ia] IIC > Galvanic isolation between input, output and power supply > Open-circuit and short-circuit monitoring and messaging for input
More informationFieldIT Temperature Transmitter, rail mounted TH102/TH102-Ex
Data Sheet 10/-8.54 EN Level 0: Information FieldIT Temperature Transmitter, rail mounted TH102/TH102-Ex HART programmable, Pt 100 (RTD), thermocouples, electrical isolation Resistance thermometer (2,
More informationSpecifications. Specifications. Transfer Characteristics Accuracy at 20 C (68 F) Temperature Drift
Appendix A Specifications 1797-IE8 and -IE8NF Input Modules Specifications Number of Inputs IS Input Type IS Module Type Resolution Transfer Characteristics Accuracy at 20 C (68 F) Temperature Drift Functional
More informationLST100 Ultrasonic level transmitter for upstream oil and gas
Data sheet DS/LST100-EN LST100 Ultrasonic level transmitter for upstream oil and gas Accurately track and measure the most expensive consumable on your site chemicals. Measurement made easy Features Keep
More informationPROGNOST -SenSim Sensor signal simulation instead of stimulation. 2ooX. Voting schemes. static and dynamic signal simulation
PROGNOST -SenSim Sensor signal simulation instead of stimulation 7 different signal types static and dynamic signal simulation 2ooX Voting schemes Enhance Safety Proof Test Intervals (PTI) Safety Instrumented
More informationInductive sensor slot-type SI2-K08-AP7
SI2-K08-AP7 Slot sensor, height 8 mm Plastic, polypropylene Mechanical end stop, removable, for analog pointer instruments 3-wire DC, 10 30 VDC NO contact, PNP output Cable connection Wiring diagram Type
More informationDigital Input Output Module for Zone 1 Series 9470/32
www.stahl.de > 16 can be adjusted in pairs as digital input or output > Intrinsically safe inputs/outputs Ex ia > For contacts, NAMUR proximity switches and low-power solenoid valves > Up to 8 can be used
More informationLexium integrated drives
Description ILp for CANopen, PROFIBUS DP, RS ILA with AC synchronous servo motor Description ILA comprise control electronics with a fieldbus interface for CANopen DS, PROFIBUS DP or RS and an AC synchronous
More informationMiniature resistance thermometer Explosion-protected version Model TR34, thread-mounted
Electrical temperature measurement Miniature resistance thermometer Explosion-protected version Model TR34, thread-mounted WIKA data sheet TE 60.34 Applications Machine building, plant and vessel construction
More informationTrendmaster * Dynamic Scanning Module
149744 Trendmaster * Dynamic Scanning Module Product Datasheet Bently Nevada * Asset Condition Monitoring Description The 149744 Trendmaster* Dynamic Scanning Module (DSM) is a compact rack-based data
More informationBinary Output without Power Supply Series 9176
Binary Output without Power Supply Series 9176 > For intrinsically safe operation of Ex i solenoid valves, indicators and horns > Power supply by control circuit, loop powered > Intrinsically safe output
More informationApplications Note. Bently Nevada* Asset Condition Monitoring. Periodically Monitored Assets. Connecting SCOUT to Continuous Monitoring Systems
Bently Nevada* Asset Condition Monitoring Connecting SCOUT to Continuous Monitoring Systems The most effective installations of continuous monitoring instruments such as the 3500 system include integration
More informationIsolators A3/1. Ex i Power Supply Field Circuit Ex i Series
> Intrinsically safe output [Ex ib] IIC/IIB > Stable output voltage > Galvanic isolation between output and power supply > Power supply or 85... 230 V AC > Compact design www.stahl.de 07673E00 Basic function:
More informationSTT 3000 Series STT170 SMART TEMPERATURE TRANSMITTER Models STT171, STT173, STT17H, STT17F, STT17C
STT 3000 Series STT170 SMART TEMPERATURE TRANSMITTER Models STT171, STT173, STT17H, STT17F, STT17C 6/07 PRODUCT SPECIFICATION SHEET OVERVIEW The Honeywell STT170 series of programmable temperature transmitters
More informationDigital Input Output Module for Zone 2 Series 9470/33
www.stahl.de > 16 can be adjusted in pairs as digital input or output > Intrinsically safe inputs/outputs Ex ia > For contacts, NAMUR proximity switches and low-power solenoid valves > Up to 8 can be used
More informationElectrodynamic Velocity Sensor
PR9268 Specifications Sheet July 2018 Electrodynamic Velocity Sensor Mechanical velocity sensor for absolute vibration measurement of critical turbomachinery applications such as steam, gas and hydro turbines,
More informationBinary Output Series 9175
Binary Output > Intrinsically safe output [Ex ia] IIC / [Ex ib] IIC > Galvanic isolation between input, output and power supply > Open-circuit and short-circuit monitoring (can be switched off) > For use
More informationSEM210 SERIES. Programmable In-head Universal Temperature Transmitter INDEX SECTION CONTENTS PAGE NO.
INDEX SECTION CONTENTS PAGE NO. SEM210 SERIES 1.0 DESCRIPTION 1 2.0 SPECIFICATION 15 3.0 INSTALLATION 67 Programmable Inhead Universal Temperature Transmitter Status Instruments Ltd, Green Lane Business
More informationMACX MCR-EX-T-UI-UP. Extract from the online catalog. Order No.:
Extract from the online catalog MACX MCR-EX-T-UI-UP Order No.: 2865654 Freely programmable Ex-i temperature transducer with analog output and 1 limit value relay, standard configuration, resistance thermometer
More informationRemote I/O. 74 Remote I/O. Remote I/O System
System Overview of the System Components IS1+ 76 General Information IS1+ 77 CPU & Power Modules CPU & Power Modules for Zone 1 / Div. 1 IS1+ 9440/22 78 Sockets for CPU & Power Module IS1+ 9490 78 CPU
More informationthe 3500/44M Aeroderivitive GT Vibration Monitor for the
3500/44M Aeroderivitive GT Vibration Monitor Product Datasheet Bently Nevada* Asset Condition Monitoring Description The 3500/44M Aeroderivitive GT Vibration Monitor is a fourchannel instrument designed
More informationRail mounted Temperature Transmitter TH102/TH102-Ex
Data Sheet 10/-8.54 EN Rail mounted Temperature Transmitter TH102/TH102-Ex HART programmable, Pt 100 (RTD), thermocouples, electrical isolation Input Resistance thermometer (2, 3, 4 wire circuit) Thermocouples
More informationC520 / C520X /C520S / C520XS HART Compatible, Universal, Dual-input 2-wire Transmitters
C520 / C520X /C520S / C520XS HART Compatible, Universal, Dual-input 2-wire Transmitters The 520 transmitters are universal, isolated, dual-input temperature transmitters with additional voltage and resistance
More informationCondition Monitoring Custom Products
CMCP500 Series Transmitters/Monitors Low Cost Din rail mount 4-20 ma output Sensor fault detection Buffered transducer output Optional filters Alert, Danger & OK Alarms and Relays Trip Multiply Remote
More informationDescription. Annexe to: IECEx CML X Issue 1. Isolating Amplifier D461
October 13, 2017 Annexe to: IECEx CML 15.0063X Issue 1 Applicant: Apparatus: Braun GmbH Isolating Amplifier D461 Description The Isolating Amplifier D461 is an intrinsic safety associated apparatus
More informationC330 / C330X PC-Programmable Universal, 2-wire Transmitter
C330 / C330X PC-Programmable Universal, 2-wire Transmitter The IPAQ C330 transmitter is a universal, isolated, temperature transmitter with additional voltage and resistance input. Its robust design and
More informationIsolators A3/1. Transmitter Supply Unit Field Circuit Ex i Series 9160
Series 9160 > Intrinsically safe input [Ex ia] IIC > Galvanic isolation between input, output and power supply > For use up to SIL 2, special version up to SIL 3 (IEC 61508) > High accuracy www.stahl.de
More informationDigital Temperature Transmitters Model T12.10, Universally Programmable, Head Mounting Model T12.30, Universally Programmable, Rail Mounting
Electrical Temperature Measurement Digital Temperature Transmitters Model T12.10, Universally Programmable, Head Mounting Model T12.30, Universally Programmable, Rail Mounting WIKA Data Sheet TE 12.03
More informationIsolators A3/1. Transmitter Supply Unit Field Circuit Ex i Series 9160 Rev. F
Series 9160 Rev. F > Intrinsically safe input [Ex ia] IIC > Galvanic isolation between input, output and power supply > For use up to SIL 2, special version up to SIL 3 (IEC 61508) > High accuracy www.stahl.de
More information2-WiRE LEvEL TRansmiTTER PRELEvEL 5343 ConTEnTs
2-wire level transmitter PRelevel 5343 Contents EC declaration of conformity... 14 Application... 15 Technical characteristics... 15 Mounting / installation... 15 Applications... 16 Electrical specifications...
More informationProduct Specifications
Product Specifications VC-6000 Monitoring System Monitoring Module SM-610-A07 User-Defined: up to 12x Vibration inputs, up to 12 x process inputs (galvanic isolated), up to 12x Axial position, up to 2x
More information3500/40M Proximitor Monitor
Specifications and Ordering Information 3500/40M Proximitor Monitor Description The 3500/40M Proximitor Monitor is a 4-channel monitor that accepts input from Bently Nevada proximity transducers, conditions
More informationSTT 3000 Smart Temperature Transmitter Series STT170 Specifications
STT 3000 Smart Temperature Transmitter Series STT170 Specifications Model STT171, STT173, STT17H, STT17F, STT17C 34-TT-03-07 November 2010 Overview STT17H Features The Honeywell STT170 series of programmable
More informationCSI 9330 Vibration Transmitter
Machinery Health Management O-9330-110512 Product Data Sheet November 2012 CSI 9330 Vibration Transmitter n Continuously monitors critical machinery in process applications and other industrial environments
More informationIsolators A3/1.
> Compact limit value switch with 2 configurable limiting values and 4... 20 ma output > Suitable for 2-, 3-wire transmitters, 2-wire HART transmitters and ma sources > Intrinsically safe input [Ex ia]
More informationJUMO dtrans T01 HART / T01T HART / T01 Junior / T01 Ex / T01 HART Ex Programmable 2-wire transmitter
JUMO GmbH & Co. KG Delivery address: Mackenrodtstraße 14 36039 Fulda, Germany Postal address: 36035 Fulda, Germany Phone: 49 661 60030 Fax: 49 661 6003607 Email: mail@jumo.net Internet: www.jumo.net JUMO
More informationXMV16 / XIO16T Extended vibration monitoring card pair XMV16
Extended vibration monitoring card pair XMV16 FEATURES» From the Vibro-Meter product line» Designed for operation with the VibroSight software total monitoring solution» 16 dynamic vibration channels and
More informationOEM miniature resistance thermometer Models TR31-3 and TR31-K, thread-mounted
Electrical temperature measurement OEM miniature resistance thermometer Models TR31-3 and TR31-K, thread-mounted WIKA data sheet TE 60.31 further approvals see page 10 Applications Machine building, plant
More information09746E00. ATEX / IECEx NEC 505 NEC 506 NEC 500 Class I Class I Class II Class III Zone Zone Division Ex i
Temperature Transmitter Series 9182 www.stahl.de > One unit for nearly all temperature sensors indivdually configurable > Intrinsically safe input [Ex ia] IIC > Signal duplication possible > Galvanic isolation
More informationResistance thermometer Model TR30, compact design
Electrical temperature measurement Resistance thermometer Model TR30, compact design WIKA data sheet TE 60.30 Applications Machine building, plant and vessel construction Propulsion technology, hydraulics
More informationOPTITEMP TT 10 C/R Technical Datasheet
OPTITEMP TT 10 C/R Technical Datasheet Analogue 2-wire temperature transmitter Temperature linear 4...20 ma output Rangeable with solder pads and potentiometers Easy wiring through large center hole The
More informationJUMO dtrans T01 HART / T01T HART / T01 Junior / T01 Ex / T01 HART Ex Programmable 2-wire transmitter
JUMO GmbH & Co. KG Delivery address: Mackenrodtstraße 14 36039 Fulda, Germany Postal address: 36035 Fulda, Germany Phone: 49 661 60030 Fax: 49 661 6003607 Email: mail@jumo.net Internet: www.jumo.net JUMO
More informationPRetrans Table of contents
HART TRANSPARENT REPEATER PRetrans 5106 Table of contents Warnings 16 Safety instructions 17 EC Declaration of Conformity 19 How to demount SYSTEM 5000 20 Application 21 Technical characteristics 21 Mounting
More information06528E00. ATEX / IECEx NEC 505 NEC 506 NEC 500
Switching Repeater Series 9170 > Intrinsically safe input [Ex ia] IIC > Galvanic isolation between input, output and power supply > Open-circuit / short-circuit monitoring and messaging (can be switched
More informationMCR-FL-TS-LP-I-EX SIL IEC Programmable Intrinsically Safe Loop-Powered Temperature Measuring Transducer With HART Protocol
SIL IEC 6 508 Programmable Intrinsically Safe Loop-Powered Temperature Measuring Transducer With HART Protocol Data Sheet 0068_en_03 PHOENIX CONTACT 0-07-09 Description Temperature FL ϑ Universal PC programmable
More informationRosemount 848L Logic Transmitter with FOUNDATION Fieldbus
Logic Transmitter with FOUNDATION Fieldbus Integrates Discrete I/O on a FOUNDATION Fieldbus H1 Segment Reduces Installation and Maintenance Costs with a Single Network for Analog and Discrete devices Easily
More informationIsolating Repeater Input Series 9163
> For 4-wire HART transmitters and voltage sources > Intrinsically safe input [Ex ia] IIC > Galvanic isolation between input, output and power supply > For use up to SIL 2 (IEC 61508) > High accuracy www.stahl.de
More informationProduct Specifications
Product Specifications VC-6000 Monitoring System Monitoring Module SM-610-A06 User-Defined: up to 11x Vibration inputs, up to 2x Axial position, up to 2x Phase Reference/Speed with 8x DC Outputs and 2x
More informationHead mounted Temperature Transmitter TF02/TF02-Ex
Data Sheet Head mounted Temperature Transmitter TF0/TF0-Ex FOUNDATION Fieldbus H, Pt 00 (RTD), thermocouples, or independent channels Input Resistance thermometer (-, -, -wire circuit) Thermocouples Resistance
More information9330 Vibration Transmitter
Reliability Solutions Product Data Sheet June 2017 9330 Vibration Transmitter Continuously monitors critical machinery in process applications and other industrial environments Interfaces with existing
More informationTÜV NORD CERT. TÜV NORD CERT GmbH & Co. KG Am TÜV 1 D Hannover. Annexe to IECEx TUN , issue No. 0 Page 1 of 5.
GmbH & Co. KG Page 1 of 5 Electrical data: Base devices for 6DR50**-*****-**** Motherboard L250 Power supply / control current 4-20 ma... series connection (terminals 6+ and 7/8) 2-wire circuit with Hart
More informationRotary Measuring Technology
Our ATEX encoders now also carry approval for Dust Flameproof-enclosure type of construction with approval for Zone 1 and 21 ExII2GEExdIICT6 and ExII2DIP6xT85 C Shaft ø 12 mm One type for every situation:
More informationIntrinsically safe pressure transmitter For applications in hazardous areas Models IS-20-S, IS-21-S, IS-20-F, IS-21-F
Replacement product: Model IS-3 Electronic pressure measurement Intrinsically safe pressure transmitter For applications in hazardous areas Models IS-20-S, IS-21-S, IS-20-F, IS-21-F WIKA data sheet PE
More informationPRODUCT DATA. 16-channel DeltaTron Conditioning Amplifiers Types 2694-A/B/C/D. Features and Uses
PRODUCT DATA 16-channel DeltaTron Conditioning Amplifiers s -A/B/C/D The family of 16-channel DeltaTron conditioning amplifiers comprises of general signal- conditioning amplifiers for voltage and DeltaTron
More information3 Ex i Isolators. Temperature Transmitter with Output 0/ ma, without Limit Value Contact (Field Circuit Ex i) Type 9182/.0-5.
Ex i Isolators Temperature Transmitter with Output 0/4... 20 ma, without Limit Value Contact Field Circuit Ex i) One unit for nearly all temperature sensors indivdually configurable Intrinsically safe
More informationMotor Vibration. Detect Mechanical & Electrical Motor Faults with Vibration Monitoring Instrumentation. IMI Sensors - A PCB Piezotronics Division
IMI Sensors - A PCB Piezotronics Division Motor Vibration Detect Mechanical & Electrical Motor Faults with Vibration Monitoring Instrumentation visit us at www.pcb.com/imi-sensors Predictive Maintenance
More information1715 Redundant I/O System Specifications
Technical Data 1715 Redundant I/O System Specifications System Module Catalog Numbers 1715-AENTR, 1715-IB16D, 1715-OB8DE,1715-IF16, 1715-OF8I Base Unit Catalog Numbers 1715-A2A, 1715-A3IO Termination Assembly
More informationHigh Temperature Velocity and Acceleration Sensor
359 High Temperature Velocity and Acceleration Sensor Bently Nevada* Asset Condition Monitoring Description The 359 High Temperature Velocity and Acceleration Sensor (HTVAS) provides a continuous acceleration
More informationTF 02 / TF 02-Ex. Head mounted temperature transmitters, FOUNDATION Fieldbus (H1), Pt 100 (RTD), thermocouples, 1 or 2 independent channels
TF 0 / TF 0-Ex Head mounted temperature transmitters, FOUNDATION Fieldbus (H), Pt 00 (RTD), thermocouples, or independent channels 0/-8.5 EN Input Resistance thermometer (,, wire circuit) Thermocouples
More information3500/64M Dynamic Pressure Monitor
3500/64M Dynamic Pressure Monitor Product Datasheet Bently Nevada* Asset Condition Monitoring Description The 3500/64M Dynamic Pressure Monitor is a single slot, fourchannel monitor that accepts input
More informationDeltaV SIS Hardware Carriers
DeltaV SIS Process Safety System Product Data Sheet September 2013 DeltaV SIS Hardware Carriers The DeltaV SIS modular architecture is easy to install and maintain. Provides an additional level of economical
More information3500/46M Hydro Monitor
3500/46M Hydro Monitor Smart Monitoring for the Intelligent Machine Age Mark Snyder Bently Nevada Senior Field Application Engineer mark.snyder@ge.com Older machinery protection systems, and even transmitters
More informationCONTINUOUS CONDITION MONITORING WITH VIBRATION TRANSMITTERS AND PLANT PLCS
SENSORS FOR MACHINERY HEALTH MONITORING WHITE PAPER #47 CONTINUOUS CONDITION MONITORING WITH VIBRATION TRANSMITTERS AND PLANT PLCS www.pcb.com/imi-sensors imi@pcb.com 800.828.8840 Continuous Condition
More informationSELECTION GUIDE. Interfaces galvanic insulation.
SELECTION GUIDE Interfaces galvanic insulation 1. and notions of intrinsic safety 1. 4 2. Notions of intrinsic safety 7 2. 1. Mechanical properties 12 2. Certifications 12 3. Dimensions 12 3. Selection
More informationAnalogue Temperature Transmitter Model T24.10, PC configurable, Head Mounting
Electrical Temperature Measurement Analogue Temperature Transmitter Model T24.10, PC configurable, Head Mounting WIKA Data Sheet TE 24.01 Applications T Machinery, plant construction T Process industry
More information3 Ex i Isolators. Temperature Transmitter without Output 0/ ma, with Limit Value Contact (Field Circuit Ex i) Type 9182/.
Ex i Isolators Temperature Transmitter without Output 0/4... 20 ma, with Limit Value Contact Field Circuit Ex i) One unit for nearly all temperature sensors indivdually configurable Intrinsically safe
More informationMACX MCR-EX-SL-RPSSI-I
Extract from the online catalog MACX MCR-EX-SL-RPSSI-I Order No.: 2865340 Ex-i repeater power supply and input isolation amplifier, HART. Sends fed or active 0/4-20 ma signals from the Ex area to a load
More informationPV 102. IECEx. Piezoelectric velocity sensor FEATURES. From the Vibro-Meter product line
FEATURES From the Vibro-Meter product line Designed for medium temperature industrial applications: 50 to +120 C ( 58 to +248 F) Frequency response: 6.0 to 2500 Hz: ±10 % to 5000 Hz: ±3 db Ultra low-noise
More informationOperating Instructions
Level and Pressure Operating Instructions VEGATOR 620, 621, 622 max. 0 10 min. 0 10 on VEGATOR 622! 6 7 8 9 10 11 12 13 14 in out Contents Contents Safety information... 2 Note Ex area... 2 1 Product description
More informationResistance thermometer Model TR30, compact design
Electrical temperature measurement Resistance thermometer Model TR30, compact design WIKA data sheet TE 60.30 Applications Machine building, plant and vessel construction Propulsion technology, hydraulics
More informationDigital temperature transmitter with HART protocol Model T32.1S, head mounting version Model T32.3S, rail mounting version
Electrical temperature measurement Digital temperature transmitter with HART protocol Model T32.1S, head mounting version Model T32.3S, rail mounting version WIKA data sheet TE 32.04 Applications Process
More informationInstallation guide 873 SmartRadar Control Unit & Antenna Unit
Installation guide 873 SmartRadar Control Unit & Antenna Unit Rev. 7 January 2006 Part no. 4416.569 Enraf BV PO Box 812 2600 AV Delft Netherlands Tel. : +31 15 2701 100 Fax : +31 15 2701 111 E-mail : info@enraf.nl
More informationGlass-fibre-reinforced polycarbonate. Dead zone Adaptive or fixed from % 1.5 s adjustable. 20 ms. 60 ms. 60 ms. Approx. 1.
General data Mounting On linear actuators On quarter turn actuators ARCA-integrated or to VDI/VDE 3847-1 or IEC 534-6 (NAMUR) Range of stroke: 3... 130 mm Integrated to VDI/VDE 3847-2 or VDI/VDE 3845 Angle
More informationINTER PLANT STANDARD STEEL INDUSTRY
INTER PLANT STANDARD STEEL INDUSTRY IPSS SPECIFICATION FOR VIBRATION MEASURING SYSTEM FOR LOW SPEED MACHINES (Second Revision) Corresponding IS does not exist IPSS:2-07-027-11 Formerly: IPSS:2-07-027-97
More informationATA-2001 Analog LVDT/RVDT Signal Conditioner with digital calibration
115 or 220 VAC operation Microprocessor controlled calibration Superior digital filtering Selectable excitation frequencies & amplitudes Voltage and current outputs 250 to 1000Hz selectable frequency response
More informationSKF Multilog On-line System WVT
SKF Multilog On-line System WVT CMWA 7910 Cost effective, reliable and secure wireless condition monitoring for semi-critical and balance-of-plant machinery Introduction The SKF Multilog On-line System
More informationDIFFERENTIAL CURRENT GENERATOR «POCDIF» (AC/DC - 32A - 50V - 12 ranges)
PERFORMANCES 12 ranges of AC current from 16 ma to 128 A peak AC permanent current up to 26 ARMS Nine ranges of DC permanent current from 16 ma to 12 A DC current ± 6mA or ± 10 ma stackable to AC current
More information1-830 SERIES DISPLACEMENT TRANSMITTER
1-830 SERIES DISPLACEMENT TRANSMITTER Operation & Maintenance Manual 746 Arrow Grand Circle Covina, CA 91722 United States of America Tel: (626) 938-0200 Fax: (626) 938-0202 Internet: http://www.cecvp.com
More information