LIMITED WARRANTY FOR HENNY PENNY APPLIANCES

Size: px

Start display at page:

Download "LIMITED WARRANTY FOR HENNY PENNY APPLIANCES"

Walter Griffith
5 years ago
Views:

3 LIMITED WARRANTY FOR HENNY PENNY APPLIANCES Subject to the following conditions, Henny Penny Corporation makes the following limited warranties to the original purchaser only for Henny Penny appliances and replacement parts: NEW EQUIPMENT: Any part of a new appliance, except lamps and fuses, which proves to be defective in material or workmanship within two (2) years from date of original installation, will be repaired or replaced without charge F.O.B. factory, Eaton, Ohio, or F.O.B. authorized distributor. To validate this warranty, the registration card for the appliance must be mailed to Henny Penny within ten (10) days after installation. REPLACEMENT PARTS: Any appliance replacement part, except lamps and fuses, which proves to be defective in material or workmanship within ninety (90) days from date of original installation will be repaired or replaced without charge F.O.B. factory, Eaton, Ohio, or F.O.B. authorized distributor. The warranty for new equipment and replacement parts covers only the repair or replacement of the defective part and does not include any labor charges for the removal and installation of any parts, travel or other expenses incidental to the repair or replacement of a part. EXTENDED FRYPOT WARRANTY: Henny Penny will replace any frypot that fails due to manufacturing or workmanship issues for a period of up to seven (7) years from date of manufacture. This warranty shall not cover any frypot that fails due to any misuse or abuse, such as heating of the frypot without shortening. 0 TO 3 YEARS: During this time, any frypot that fails due to manufacturing or workmanship issues will be replaced at no charge for parts, labor, or freight. Henny Penny will either install a new frypot at no cost or provide a new or reconditioned replacement fryer at no cost. 3 TO 7 YEARS: During this time, any frypot that fails due to manufacturing or workmanship issues will be replaced at no charge for the frypot only. Any freight charges and labor costs to install the new frypot as well as the cost of any other parts replaced, such as insulation, thermal sensors, high limits, fittings, and hardware, will be the responsibility of the owner. Any claim must be presented to either Henny Penny or the distributor from whom the appliance was purchased. No allowance will be granted for repairs made by anyone else without Henny Penny s written consent. If damage occurs during shipping, notify the sender at once so that a claim may be filed. THE ABOVE LIMITED WARRANTY SETS FORTH THE SOLE REMEDY AGAINST HENNY PENNY FOR ANY BREACH OF WARRANTY OR OTHER TERM. BUYER AGREES THAT NO OTHER REMEDY (INCLUDING CLAIMS FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES) SHALL BE AVAILABLE. The above limited warranty does not apply (a) to damage resulting from accident, alteration, misuse, or abuse; (b) if the equipment s serial number is removed or defaced; or (c) for lamps and fuses. THE ABOVE LIMITED WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND FITNESS, AND ALL OTHER WARRANTIES ARE EXCLUDED. HENNY PENNY NEITHER ASSUMES NOR AUTHORIZES ANY PERSON TO ASSUME FOR IT ANY OTHER OBLIGATION OR LIABILITY. FM Revised

64 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 SECTION 6. PARTS INFORMATION HM-3/5/7 Service Parts List Part Qty. Per Unit No. Number Description Front Viewing Glass - 3 Pan (Before July 1, 1994) Front Viewing Glass Assy. - Complete - 3 Pan Front Viewing Glass Assy. - 5 Pan (Before July 1,1994) Front Viewing Glass Assy. - Complete - 5 Pan Front Viewing Glass Assy. - 7 Pan (Before July 1,1994) Front Viewing Glass Assy. Complete - RH - 7 Pan Front Viewing Glass Assy. Complete - LH - 7 Pan Sliding Door Assembly - 3 Pan Sliding Door Assembly - 5 Pan Sliding Door Assembly - 7 Pan Water Pan Assembly (Before July 1, 1994) Water Pan Assembly * Probe Bracket * Temperature Probe PC Board Assy Blower Motor Series Regulating Thermostat Transformer PL01-006* Plug - Bottom Recommended replacement parts, stocked by your distributor, End Clamp are indicated with in the parts lists. 11 MS Mounting Channel Please use care when Terminal Block ordering recommended parts, Barrier because all voltages and ME50-003* Spacer variations are marked. Distributors NS03-013* Cage Nut should order parts based EF02-040* Bushing - Snap upon common voltages and Bracket - Drop Shelf equipment sold in their territory Side Viewing Panel Side Viewing Panel - (Mir)-Left Side Viewing Panel - (Mir)-Right Fan Blade Fan Guard Heater - Lower - 240v Heater - Lower - 208v Heater - Water - 240v Heater - Water - 208v Light Socket Light Socket - CE BL Light Bulb - 120v - 100w BL Light Bulb - 240v - 60w Heater - Upper Radiant - 240v S -Shaped Heater - Upper Radiant - 208v S -Shaped Decal - Control Panel - 7 Pan - Left Decal - Control Panel - 3 Pan Decal - Control Panel - 5 Pan Decal - Control Panel - 7 Pan PC Board Assembly - Display * Bracket for Plug * Relay - 3 Pan Probe- 5 ft Receptacle Assy. - Probe (Control Panel) Receptacle Assy. - Probe (Uprights) Cooling Fan Gas Shock - 3 Pan (Before May 1, 1994) 2-2 recommended parts/*not shown **Front Viewing Glass before July 1, 1994, Tape Kit must also be ordered

65 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 HM-3/5/7 Service Parts List Continued Part Qty. Per Unit No. Number Description Gas Shock - 5 Pan (Before May 1, 1994) Gas Shock - 3 Pan Gas Shock - 5 Pan Gas Shock Assy. - 7 Pan Cutting Board - 3 Pan Cutting Board (Poly) - 3 Pan Cutting Board - 5 Pan Cutting Board (Poly) - 5 Pan Power Cord Assy. - 3 Pan Power Cord Assy. - 5 Pan Power Cord Assy. - 7 Pan PN01-016* Clevis Pin PN0l-017* Cotter Pin LW0l-004* Lockwasher Hinge Cap (Before May 1, 1994) Hinge Cap Hinge Block Assy. (Before May 1, 1994) Hinge Block Assy Hinge Block Assy. - Center - 7 Pan Hinge Pin Hinge Pin - Center Tape - Acrylic Foam Crank (Before April 1, 1994) Crank Hinge Extrusion - 3 Pan Hinge Extrusion - 5 Pan Hinge Extrusion - 7 Pan - Right Hinge Extrusion - 7 Pan - Left Clamp Extrusion - 3 Pan Clamp Extrusion - 5 Pan Clamp Extrusion - 7 Pan Pivot Support (Before May 1, 1994) Pivot Support EF Fuse - 15 Amp EF Fuse - 20 Amp EF Fuse Holder - 15 Amp EF Fuse Holder - 20 Amp Power Switch RB PC Board - Output SC06-045* Shoulder Screw Lower Track - 3 Pan Lower Track - 5 Pan Lower Track - 7 Pan Upper Track - 3 Pan Upper Track - 5 Pan Upper Track - 7 Pan * Air Deflector - 3 Pan Air Deflector - 5 Pan - Alb * Air Deflector - 5 Pan * Air Deflector - 7 Pan - Right * Air Deflector - 7 Pan Left * Replaceable Beeper * Probe * Legs recommended parts *not shown

66 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 HM-3/5/7 Service Parts List - Continued Part Qty. Per Unit No. Number Description Seal - Canopy Glass - 3 Pan (Before May 1, 1994) * Seal - Canopy Glass - 5 Pan (Before May 1, 1994) * Seal - Canopy Glass - 7 Pan (Before May 1, 1994) * Seal - Side Glass - 3 Pan * Seal - Side Glass - 5/7 Pan * Seal - Side Glass - Alb * Kit - Digital Display Uprights - O/S * Kit - Digital Display Uprights * Pan Support - Long * Pan - Cross Support Upright Stud Assy. - Right - 90 w/probe guard Upright Stud Assy. - Left - 90 w/probe guard Upright Stud Assy. - Left - O/S w/probe guard Upright Stud Assy. - Right - O/S w/probe guard * Right Water Pan Support Bracket * Left Water Pan Support Bracket *not shown HMT-3/5/7 Service Parts List Part Qty Per Unit No. Number Description Front Viewing Glass - 3 Pan (Before July 1, 1994) Front Viewing Glass Assy. - Complete - 3 Pan Front Viewing Glass Assy. Complete - 3 Pan - Huss Front Viewing Glass Assy. Complete - 3 Pan - Tyler Front Viewing Glass Assy. - 5 Pan (Before July 1,1994) Front Viewing Glass Assy. Complete - 5 Pan Front Viewing Glass Assy. Complete - 5 Pan - Huss Front Viewing Glass Assy. Complete - 5 Pan - Tyler Front Viewing Glass Assy. - 7 Pan (Before July 1,1994) Front Viewing Glass Assy. Complete - RH - 7 Pan Front Viewing Glass Assy. Complete - LH - 7 Pan Front Viewing Glass Assy. Complete - 7 Pan - Huss RH Front Viewing Glass Assy. Complete - 7 Pan - Huss. LH Front Viewing Glass Assy. Complete - 7 Pan - Tyler RH Front Viewing Glass Assy. Complete - 7 Pan - Tyler LH Sliding Door Assy. - 3 Pan Sliding Door Assy. - 5 Pan Sliding Door Assy. - HMT-5 (4 doors) Sliding Door Assembly - 7 Pan Water Pan Assembly (Before July 1, 1994) Water Pan Assembly * Probe Bracket * Temperature Probe PC Board Assy Blower Motor Series Regulating Thermostat Transformer PL01-006* Plug - Bottom End Clamp **Front viewing glass before July 1, 1994, Tape Kit must also be ordered. recommended parts/*not shown

67 Henny Penny HMT-3/5/7 Service Parts List - Continued Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 Part Qty. Per Unit No. Number Description MS Mounting Channel Terminal Block Barrier ME50-003* Spacer NS03-013* Cage Nut EF02-040* Bushing - Snap Bracket - Drop Shelf Cutting Board Brace - KFC Side Viewing Panel Side Viewing Panel (Mir)-Left Side Viewing Panel (Mir)-Right Side Viewing Panel - Hussmann Side Viewing Panel - Hussmann (Mir)-Left Side Viewing Panel - Hussmann (Mir)-Right Side Viewing Panel - Tyler Side Viewing Panel - Tyler (Mir)-Left Side Viewing Panel - Tyler (Mir)-Right Fan Blade Fan Guard Heater Lower 240 v Heater Lower 208 v Heater Water 240 v Heater Water 208 v Socket - Light Socket - Light - CE BL Light Bulb - 120v - 100w BL Light Bulb - 240v - 60w Heater - Upper Radiant 240 v S -Shaped Heater Upper Radiant 208 v S -Shaped Decal - Control Panel - 3 Pan Decal - Control Panel - 5 Pan Decal - Control Panel - 7 Pan Decal - Control Panel - 7 Pan - Left Decal - Control Panel - KFC PC Board Assembly - Control Bracket for Plug Relay Probe - 5 ft Plug - Probe Receptacle Assy. - Probe (Control Panel) Receptacle Assy. - Probe (Uprights) Cooling Fan Gas Shock - 3 Pan (Before April 1, 1994) Gas Shock - 3 Pan Gas Shock - 5 Pan (Before April 1, 1994) Gas Shock - 5 Pan Gas Shock Assy. - HM Cutting Board - 3 Pan Cutting Board (Poly) - 3 Pan Cutting Board - 5 Pan Cutting Board (Poly) - 5 Pan Cutting Board - KFC - HMT Cutting Board - KFC - HMT Power Cord Assy. - 3 Pan Power Cord Assy. - 5 Pan Power Cord Assy. - 7 Pan PN01-016* Clevis Pin PN01-017* Cotter Pin LW01-004* Lockwasher recommended parts/*not shown

68 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 HMT-3/5/7 Service Parts List - Continued Part Qty. Per Unit No. Number Description Hinge Cap (Before April 1, 1994) Hinge Cap Hinge Block Assy. (Before April 1, 1994) Hinge Block Assy Hinge Block Assy. - Center - 7 Pan Hinge Pin Hinge Pin - Center - 7 Pan Tape - Acrylic Foam Crank (Before April 1, 1994) Crank Hinge Extrusion - 3 Pan Hinge Extrusion - 5 Pan Hinge Extrusion -7 Pan - Right Hinge Extrusion - 7 Pan-Left Clamp Extrusion -3 Pan Clamp Extrusion - 5 Pan Clamp Extrusion - 7 Pan Pivot Support EF use - 15 Amp EF use - 20 Amp EF use Holder - 15 Amp EF use Holder - 20 Amp ower Switch PC Board - Output SC06-045* Shoulder Screw SC06-060* Shoulder Screw - HMT Lower Track - 3 Pan Lower Track - 5 Pan Lower Track - 7 Pan Upper Track - 3 Pan Upper Track - 5 Pan Upper Track - 7 Pan * Air Deflector - 3 Pan * Air Deflector - 5 Pan * Air Deflector - 7 Pan * Replaceable Beeper * Probe * Legs * Seal - Canopy Glass - 3 Pan (Before April 1, 1994) * Seal - Canopy Glass - 5 Pan (Before April 1, 1994) * Seal - Canopy Glass - 7 Pan (Before April 1, 1994) * Seal - Side Glass * Seal - Side Glass - Huss * Seal - Side Glass - Tyler Kit - Digital Display Uprights - 90' Kit - Digital Display Uprights - O/S * Pan Support - Long * Pan - Cross Support Upright Stud Assy. - Left - 90º - D/D - Probe Guard Upright Stud Assy. - Rt. - 90º - D/D - Probe Guard Upright Stud Assy. - Right - O/S -D/D- Probe Guard Upright Stud Assy. - Left - O/S- D/D - Probe Guard Bun Pan Insert - KFC - KMT Bun Pan Insert - KFC - KMT * Right Water Pan Support Bracket * Left Water Pan Support Bracket Contactor- 3 ph Albertsons * Decal Meat Probe Temp. Display recommended parts/*not shown

69 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 CM/CMT-5/7 Service Parts List Part Qty. Per Unit No. Number Description Front Viewing Glass - CM/CMT-5 (before July 1, 1994) Front Viewing Glass Assy. Complete. - CM-5 RH Front Viewing Glass Assy. Complete - CM-5 LH Front Viewing Glass Assy. Complete - CMT-5 RH Front Viewing Glass Assy. Complete - CMT-5 LH 1-1A Glass-Canopy Guard - Assy. Complete - CM-5/7 RH 1 1 1A Glass-Canopy Guard - Assy. Complete - CM-5/7 LH Front Viewing Glass - CM/CMT-7 (before July 1, 1994) Front Viewing Glass Assy. - CM-7 RH Front Viewing Glass Assy. - CM-7 LH Front Viewing Glass Assy. - CMT-7 RH Front Viewing Glass Assy. - CMT-7 LH - 1 1A Glass Canopy Guard Complete - CMT-5/7 RH 1 1 1A Glass Canopy Guard Complete- CMT-5/7 LH Front View Glass Assy. Complete - CMT-5-Huss. LH Front View Glass Assy. Complete - CMT-5-Huss. RH Front Viewing Glass Assy. Complete - CMT-5-Tyler RH Front Viewing Glass Assy. Complete - CMT-5-Tyler LH Front Viewing Glass Assy. Complete - CMT-7-Huss. RH Front Viewing Glass Assy. Complete - CMT-7-Huss. LH - 1 1A Glass Canopy Guard Assy. Complete - CMT-5/7-Huss. LH 1 1 1A Glass Canopy Guard Assy. Complete - CMT-5/7-Huss. RH Front Viewing Glass Assy. Complete - CMT-7-Tyler RH Front Viewing Glass Assy. Complete - CMT-7-Tyler LH - 1 1A Glass Canopy Guard Assy. Complete - CMT-5/7-Tyler LH 1 1 1A Glass Canopy Guard Assy. Complete - CMT-5/7-Tyler RH Sliding Door Assembly - CM Sliding Door Assembly - CM Sliding Door Assembly - CMT Sliding Door Assembly - CMT Water Pan Assembly (Before July 1, 1994) Water Pan Assembly * Probe Bracket * Temperature Probe PCB Assembly Blower Motor Series Regulating Thermostat Transformer PL01-006* Plug-Bottom End Clamp MS Mounting Channel Terminal Block Barrier ME Spacer NS Cage Nut EF Bushing- Snap Bracket - Drop Shelf A Glass - Center Panel - CM-5/7 1 l Side Viewing Panel - CM-5/ Side Viewing Panel - Mir.-CM-5/7-Left Side Viewing Panel - Mir.-CM-5/7-Right A Glass - Center Panel - CMT-5/7 1 l Side Viewing Panel - CMT-5/ Side Viewing Panel - Mir.-CMT-5/7-Left Side Viewing Panel - Mir.-CMT-5/7-Right A Glass - Center Panel - CMT-5/7-Huss. 1 l Side Viewing Panel - CMT-5/7-Mir.-Huss.-Left Side Viewing Panel - CMT-5/7-Mir.-Huss.-Right Side Viewing Panel - CMT-5/7-Huss A Glass - Center Panel - CMT-5/7-Huss A Glass - Center Panel - CMT-5/7-Tyler 1 I Side Viewing Panel - CMT-5/7-Tyler Side Viewing Panel - CMT-5/7-Mir.-Tyler-I,eft Side Viewing Panel - CMT-5/7-Mir.-Tyler-Right Fan Blade Fan Guard Heater - Lower 240 v Heater Lower 208 v Heater Water 240 v Heater Water 208 v 1 1 recommended parts/*not shown **Front Viewing Glass before July 1, 1994, Tape Kit must also be ordered

70 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 CM/CMT-5/7 Service Parts List - Continued Part Qty. Per Unit No. Number Description Socket- Light Socket- Light - CE BL Light Bulb - 120v - 100w BL Light Bulb - 240v - 60w Heater - Upper Radiant 240 v S -Shaped Heater Upper Radiant 208 v S -Shaped Decal - Control Panel - CM/CMT-7-Left Decal - Control Panel - CM-7-Right Decal - Control Panel - CM-5 - O/S (single controls) Decal - Control Panel - CMT-5 - O/S (single controls) Decal - Control Panel - CM-5 (dual controls) Decal - Control Panel - CMT-5 (dual controls) Decal - Control Panel - CMT-7-Right Decal - Control Panel - Self Serve - CM/CMT PC Board Assembly - Display Plug for Probe * Relay Probe- 5 ft Bracket for Plug Receptacle Assy. - Probe - (Control Panel) Receptacle Assy. - Probe - (Uprights) Cooling Fan Gas Shock - 3 Pan (Before April 1, 1994) Gas Shock - 3 Pan Gas Shock - 5 Pail (Before April 1, 1994) Gas Shock Gas Shock Assy. (CM/CMT-5 & CM-7) Gas Shock Assy. (CM/CMT-5 T&H only) Gas Shock - CMT Cutting Board - 3 Pan Cutting Board - 5 Pan Power Cord Assembly - 5 Pan Power Cord Assembly - 7 Pan PN01-016* Clevis Pin PN01-107* Cotter Pin LW01-004* Lockwasher Hinge Cap (Before April 1, 1994) Hinge Cap Hinge Block Assy. (Before April 1, 1994) Hinge Block Assembly Hinge Block Assembly - Center - 7 Pan Hinge Pin Center Hinge Pin Hinge Pin CM/CMT Tape - Acrylic Foam Crank - Steel - CM-5/7 (Before April 1, 1994) Crank - Steel - CM-5/ Crank - Steel - CMT-5/7 (Before April 1, 1994) Crank - Steel - CMT-5/ Hinge Extrusion - LH - CM/CMT A Hinge Extrusion - RH - CM/CMT-5/ Hinge Extrusion - RH - CM/CMT Hinge Extrusion - RH - CM/CMT Hinge Extrusion - LH - CM/CMT Hinge Extrusion - LH - CM/CMT-5/ Clamp Extrusion - CM/CMT Clamp Extrusion - CM/CMT-7-1 recommended parts/*not shown

71 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 CM/CMT-5/7 Service Parts List - Continued Part Qty. Per Unit No. Number Description Clamp Extrusion - CM/CMT-5/ Pivot Support (Before April 1, 1994) Pivot Support EF Fuse Holder - 15 Amp 2-47 EF Fuse Holder - 20 Amp EF Fuse - 15 Amp 2-48 EF Fuse - 20 Amp Power Switch PC Board - Output SC06-045* Shoulder Screw - CM-5/ SC06-045* Shoulder Screw - CMT SC06-060* Shoulder Screw - CMT Lower Track - CM Lower Track - CMT Lower Track - CMT Lower Track - CMT Upper Track - CM/CMT Upper Track - CM/CMT Air Deflector - CM/CMT Air Deflector - CM/CMT Well Cover - 2" Flat Well Cover Well Cover- 3/ Viewing Window - CM/CMT-5/ * Replaceable Beeper * Probe - Temperature * Legs * Seal - Canopy Glass - 7 Pan (Before April 1, 1994) * Seal - Canopy Glass - 5 Pan (Before April 1, 1994) * Seal - Side Glass * Seal - Side Glass - Huss * Seal - Side Glass - Tyler * Seal - Middle Glass * Viewing Window Bracket * Pan Support - Long * Pan - Cross Support Upright Stud Assy. - Left D/D - Probe Guard Upright Stud Assy. - Rt D/D - Probe Guard Upright Stud Assy. - Rt. - O/S-D/D - Tall - Probe Guard Upright Stud Assy. - Lt - O/S-D/D - Tall - Probe Guard * Infinite Switch * Infinite Switch Knob * Power Cord Assy- 30A 3 Ph * Right Water Pan Support Bracket * Left Water Pan Support Bracket * Contactor- 3ph Albertsons * Decal Meat Probe Temp. Display 2 2 recommended parts/*not shown C E Parts Lamp holder Decal - Control Panel - CM Decal - Control Panel - HMT Decal - Control Panel - CMT Decal - Control Panel - HMT Decal - Control Panel - HS Decal - Control Panel - HMT Decal - Control Panel - HST Decal - Control Panel - HM Decal - Control Panel - HS Decal - Control Panel - HM Decal - Control Panel - HST Decal - Control Panel - HMT Decal - Output Panel - HM Decal - Control Panel - CM Decal - Output Panel - CM Decal - Control Panel - CMT Filter Board - HS/HST-3/ Filter Board - HM/HMT/CM/CMT-3/5/

72 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 HS/HST-3/5 Service Parts List Part Qty. Per Unit No. Number Description 3 5 1A Canopy Guard Assy. Complete - HST-3 1-1A Canopy Guard Assy. Complete - HST-3-Tyler 1-1A Canopy Guard Assy. Complete - HST-3-Huss 1-1A Canopy Guard Assy. Complete - HST-5-1 1A Canopy Guard Assy. Complete - HST-5-Tyler - 1 1A Canopy Guard Assy. Complete - HST-5-Huss - 1 1A Canopy Guard Assy. Complete - HS-3 1-1A Canopy Guard Assy. Complete - HS Sliding Door Assembly - HST Sliding Door Assembly - HS Sliding Door Assembly - HS PL01-006* Plug - Bottom End Clamp MS Mounting Channel Terminal Block Barrier ME Spacer.250 TH,.281 LG,.171 I.D NS Cage Nut EF Bushing - Snap Bracket - Drop Shelf Side Viewing Panel - HS-3/ Side Viewing Panel - HS-3/5 (Mir)-Left Side Viewing Panel - HS-3/5 (Mir)-Right Side Viewing Panel - HST-3/ Side Viewing Panel - HST-3/5 (Mir)-Left Side Viewing Panel - HST-3/5 (Mir)-Right Side Viewing Panel - HST-5-Huss Side Viewing Panel - HST-5-Huss (Mir)-Left Side Viewing Panel - HST-5-Huss (Mir)-Right Side Viewing Panel - HST-5-Tyler Side Viewing Panel - HST-5-Tyler (Mir)-Left Side Viewing Panel - HST-5-Tyler (Mir)-Right Heater - Lower v Heater - Lower v Socket - Light Socket - Light - CE BL Light Bulb V W BL Light Bulb V - 60 W Heater - Upper Radiant 240 v S -Shaped Heater - Upper Radiant 208 v S -Shaped Decal - Control Panel - HS Decal - Control Panel - HS Decal - Control Panel - HST Decal - Control Panel - HST Relay - HS/HST-5 only Gas Shock (Before April 1, 1994) Gas Shock - HS/HST Gas Shock - HS/HST Cutting Board - 3 Pan Cutting Board (Poly) - 3 Pan Cutting Board - 5 Pan Cutting Board (Poly) - 5 Pan Wire Grid - HS/HST Wire Grid - HS/HST Power Cord Assembly - 3 Pan Power Cord Assembly - 5 Pan - 1 recommended parts/*not shown

73 Henny Penny Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 HS/HST-3/5 Service Parts List - Continued Part Qty. Per Unit No. Number Description PN01-016* Clevis Pin PN01-017* Cotter Pin - HS PN01-017* Cotter Pin - HST LW01-004* Lockwasher Hinge Cap (Before April 1, 1994) Hinge Cap Hinge Block Assy. (Before April 1, 1994) Hinge Block Assy Hinge Pin Tape - Acrylic Foam Crank-HS (Before May 1, 1994) Crank-HST (Before April 1, 1994) Crank-HS Crank-HST A Hinge Extrusion - HS/HST A Hinge Extrusion - HS/HST Clamp Extrusion - HS/HST Clamp Extrusion - HS/HST Pivot Support (Before May ) Pivot Support EF Fuse EF Fuse Holder Power Switch SC Shoulder Screw Lower Track - HS Lower Track - HS Lower Track - HST Lower Track - HST Upper Track - HS/HST Upper Track - HS/HST Well Cover - HS/HST-3 (Bun Pans) Well Cover-3/8 - HS/HST Well Cover-2 - HS/HST Well Cover-3/8 - HS/HST Well Cover-2 - HS/HST Well Cover-Flat - HS Well Cover-Flat - HS Viewing Window - HS/HST Viewing Window - HS/HST * Legs * Seal-Canopy Glass (Before April 1, 1994) * Seal- Side Glass - HS * Seal-Side Glass - HS * Seal-Side Glass - HST-3/ * Viewing Window Bracket - HS/HST * Viewing Window Bracket - HS/HST * Pan Insert Assy.-HS/HST - 3 (Before May 1, 1994) * Seal-Front Viewing Glass - HS/HST * Seal-Front Viewing Glass - HS/HST * Pan Support-Long * Pan-Cross Support * Infinite Switch * Infinite Switch Knob * Sneeze Guard - HST * Sneeze Guard - HST * Filter Board - CE * Contactor- 3ph Albertsons - 1 recommended parts/*not shown

WARRANTY REGISTRATION AND POLICY

WARRANTY REGISTRATION AND POLICY Buhler Manufacturing products are warranted for a period of twelve (12) months from original date of purchase, by original purchaser, to be free from defects in material