APPLICATION SPECIFICATION LEAD FREE REFLOW PROFILE FOR SMD S AND WAVE SOLDERED (MODULAR TELEPHONE JACK S)
|
|
|
- Roland Thomas
- 5 years ago
- Views:
Transcription
1 APPLIATION SPEIFIATION LEAD FREE REFLOW PROFILE FOR SMD S AND WAVE SOLDERED (MODULAR TELEPHONE JAK S) 1.0 SOPE The purpose of this document is to outline the application of the surface mounted and true hole modular telephone jack onto the printed circuit board, using a hot air convection oven or a wave soldering oven. 2.0 PRODUT DESRIPTION Molex Modular Jacks provide a means of accepting the modular plugs according to FF part 68 and IE These modular jacks are intended for use with pc boards 1.57mm (0.62 ) thick. Jacks are available in 8, 6 and 4 circuit sizes. The six circuit can be loaded with 6 or 4 contacts. 3.0 REFERENE DOUMENTS The printed circuit board mounting hole layout and surface mount pattern shall be as shown on the applicable sales drawing. Panel layout shall be as shown on the applicable sales drawing. Temperature profile Ref. Spec : Jedec J-STD-020 and Molex SMES-152 REVISION: ER/EN INFORMATION: E No: E DOUMENT NUMBER: REATED / REVISED BY: HEKED BY: APPROVED BY: 1 of 5 TEMPLATE FILENAME: APPLIATION_SPE[SIZE_A4](V.1).DO
2 APPLIATION SPEIFIATION 4.0 PROEDURE 4.1 GENERAL REQUIREMENTS The Jack shall be mounted flush with the surface of the printed circuit board within the limits specified in fig 1. Max (0.10)/0.005 Max(0.10/0.005) Fig 1: Part location relative to the board Surface mount Acceptable solder Joint. Minimum Solder Joint: Solder covers lead. Maximum Solder Joint: Solder covers lead and entire pad, but does not overhang. The toe of the lead still discernible. REVISION: ER/EN INFORMATION: E No: E DOUMENT NUMBER: REATED / REVISED BY: HEKED BY: APPROVED BY: 2 of 5 TEMPLATE FILENAME: APPLIATION_SPE[SIZE_A4](V.1).DO
3 APPLIATION SPEIFIATION 4.2 ASSEMBLY INSTRUTIONS Paste printing The solder paste shall be applied using the appropriate stencil or screen and the stencil or screen shall be carefully removed to avoid smearing or the paste printed. The print paste geometry shall be verified to the P Board footprint dimensional requirements. Placement of parts The parts shall be placed on the solder print paste using suitable tools to prevent contamination and assure alignment. onvection Air reflow The jacks are soldered according to the following process (or equivalent) Fig 2 : Reflow profile DESRIPTION Average preheat ramp rate Preheat temperature Preheat time Ramp to peak Time over Liquidus (217 ) Peak Temperature Time within 5 of peak Ramp ool Down Time 25 to Peak REQUIRMENT 3 /second maximum 150 minimum; 200 maximum 60 to 180 seconds 3 /second maximum 60 to 150 seconds /-5 20 to 40 seconds 6 /second maximum 8 minutes maximum Table 1: Reflow profile REVISION: ER/EN INFORMATION: E No: E DOUMENT NUMBER: REATED / REVISED BY: HEKED BY: APPROVED BY: 3 of 5 TEMPLATE FILENAME: APPLIATION_SPE[SIZE_A4](V.1).DO
4 APPLIATION SPEIFIATION 4.3 ASSEMBLY INSTRUTIONS FOR TRUE HOLE MOUNTED JAKS. Flux Application. A uniform coating of flux is essential to successful Soldering. When spray fluxing, the uniformity of the coating can be visually checked by running a piece of cardboard over the spray fluxer or by processing a board sized piece of tempered glass through the spray and then through the preheat section. Placement of parts The parts shall be placed on the print circuit board using suitable tools to prevent contamination and assure alignment. Wave soldering The jacks are soldered according to the following process (or equivalent) Operating Parameters Amount of flux applied by spary Single wave: µg/in² ( µg/cm²) of solids Dual wave: µg/in² ( µg/cm²) of solids 105º -120º About 35º higher then top side 2 º/Second Maximum Topside Preheat Temperature Bottom Side Preheat Temperature Maximum Ramp Rate of Topside Temperature (to avoid component damage) onveyor Angle 4 º 7 º (6 º Typical) onveyor speed M./Min ontact Time in the Solder Seconds (2.5-3 Seconds (includes hip Wave and Primary most common) Wave) Solder Pot Temperature 255º - 265º These are general guidelines, however depending upon your equipment, components, and circuit boards, your optimal setting may be different. In order to optimize your process, it is recommended to perform a design experiment, optimizing the most important variables (amount of flux applied, conveyor speed, topside preheat temperature, solder pot temperature and board orientation) REVISION: ER/EN INFORMATION: E No: E DOUMENT NUMBER: REATED / REVISED BY: HEKED BY: APPROVED BY: 4 of 5 TEMPLATE FILENAME: APPLIATION_SPE[SIZE_A4](V.1).DO
5 APPLIATION SPEIFIATION 4.4 REMOVAL INSTRUTIONS Mask off any surrounding components using kapton tape. This will contain the reflow and stop smaller devices from being removed from the PB. Pre heat the PB to 60. Heat connector soldered to the board using a hot air tool, with manual temperature control (or similar equipment) temperature 380 To help remove assembly from the board, use flux (Alpha EF-6000) onto solder tails and then uniformly heat assembly. Ensure heat is applied to the tails if they pass through the boards. After heating gently remove assembly from the board using pliers. Ensure solder on all pin is molten before removing the part Do not apply excessive force when removing the part (as this will result in damage to the PB. Heating time may vary depending on Pcb layers/grounding etc. lean board using flux and braid combined with soldering iron, after this process use cleaner to finally remove all residue. REVISION: ER/EN INFORMATION: E No: E DOUMENT NUMBER: REATED / REVISED BY: HEKED BY: APPROVED BY: 5 of 5 TEMPLATE FILENAME: APPLIATION_SPE[SIZE_A4](V.1).DO
Assembly Instructions for SCC1XX0 series
Technical Note 82 Assembly Instructions for SCC1XX0 series TABLE OF CONTENTS Table of Contents...1 1 Objective...2 2 VTI's 32-lead Dual In-line Package (DIL-32)...2 3 DIL-32 Package Outline and Dimensions...2
Assembly Instructions for SCA6x0 and SCA10x0 series
Technical Note 71 Assembly Instructions for SCA6x0 and SCA10x0 series TABLE OF CONTENTS Table of Contents...1 1 Objective...2 2 VTI'S DIL-8 and DIL-12 packages...2 3 Package Outline and Dimensions...2
APPLICATION NOTE 6381 ORGANIC LAND GRID ARRAY (OLGA) AND ITS APPLICATIONS
Keywords: OLGA, SMT, PCB design APPLICATION NOTE 6381 ORGANIC LAND GRID ARRAY (OLGA) AND ITS APPLICATIONS Abstract: This application note discusses Maxim Integrated s OLGA and provides the PCB design and
PAGE 1/6 ISSUE Jul SERIES Micro-SPDT PART NUMBER R516 XXX 10X R 516 _ 1 0 _
PAGE 1/6 ISSUE Jul-24-2017 SERIES Micro-SPDT PART NUMBER R516 XXX 10X R516 series: the RAMSES concept merges with the SLIM LINE technology, breaking up the frequency limits of SMT switches : - FULL SMT
Is Now Part of To learn more about ON Semiconductor, please visit our website at
Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC
Soldering Module Packages Having Large Asymmetric Pads
Enpirion, Inc. EN53x0D AN103_R0.9 Soldering Module Packages Having Large Asymmetric Pads 1.0 INTRODUCTION Enpirion s power converter packages utilize module package technology to form Land Grid Array (LGA)
Distributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. FEATURES AND SPEIFIATIONS Features and Benefits Board-mounting pegs provide
TVNow TM (FR01-B1-S-0-047) Mobile TV Dual-band DVB-H
Mobile TV Dual-band DVB-H (UHF + L band) Antenna Fractus Antennas specializes in enabling effective mobile communications. Using Fractus technology, we design and manufacture optimized antennas to make
SMT Assembly Considerations for LGA Package
SMT Assembly Considerations for LGA Package 1 Solder paste The screen printing quantity of solder paste is an key factor in producing high yield assemblies. Solder Paste Alloys: 63Sn/37Pb or 62Sn/36Pb/2Ag
APPLICATION NOTES: Manual Soldering and De-Soldering Guideline for Primax. Introduction:
APPLICATION NOTES: Manual Soldering and De-Soldering Guideline for Primax Introduction: Primax is a super high brightness surface mount LED on a compact package outline of 3.2 x 3.2 x 1.2mm. Its high intensity
PAGE 1/6 ISSUE SERIES Micro-SPDT PART NUMBER R516 XXX 10X. (All dimensions are in mm [inches]) R 516 _ 1 0 _
![PAGE 1/6 ISSUE SERIES Micro-SPDT PART NUMBER R516 XXX 10X. (All dimensions are in mm [inches]) R 516 _ 1 0 _](/thumbs/96/127769340.jpg "PAGE 1/6 ISSUE SERIES Micro-SPDT PART NUMBER R516 XXX 10X. (All dimensions are in mm [inches]) R 516 _ 1 0 _")
PAGE 1/6 ISSUE 15-10-18 SERIES Micro-SPDT PART NUMBER R516 XXX 10X R516 series: the RAMSES concept merges with the SLIM LINE technology, breaking up the frequency limits of SMT switches : - FULL SMT TECHNOLOGY
Working Instruction, Electrical
Applicable for K700i/K700c Contents 1 Replacement of parts...2 1.1 Battery connector...2 1.2 Board to board connector...3 1.3 FPC connectors...4 1.4 Bending shield can fence...5 1.5 Replacing shield can
Application Note 5026
Surface Laminar Circuit (SLC) Ball Grid Array (BGA) Eutectic Surface Mount Assembly Application Note 5026 Introduction This document outlines the design and assembly guidelines for surface laminar circuitry
Application Note AN-1011
AN-1011 Board Mounting Application Note for 0.800mm Pitch Devices For part numbers IRF6100, IRF6100PBF, IR130CSP, IR130CSPPBF, IR140CSP, IR140CSPPBF, IR1H40CSP, IR1H40CSPPBF By Hazel Schofield and Philip
Multilayer Organic (MLO TM )
HOW TO ORDER DP 03 C 1580 Type Size Design Frequency (MHz) QUALITY INSPECTION 1 6 1 6 1 6 2 5 2 5 2 5 3 4 3 4 3 4 MLO TM TECHNOLOGY Finished parts are 100% tested for electrical parameters and visual characteristics.
AND8211/D. Board Level Application Notes for DFN and QFN Packages APPLICATION NOTE
Board Level Application Notes for DFN and QFN Packages Prepared by: Steve St. Germain ON Semiconductor APPLICATION NOTE INTRODUCTION Various ON Semiconductor components are packaged in an advanced Dual
TN008. PCB Design Guidelines for 2x2 LGA Sensors. Introduction. 2x2 LGA Package Marking
PCB Design Guidelines for 2x2 LGA Sensors Introduction This technical note is intended to provide information about Kionix s 2 x 2 mm LGA packages and guidelines for developing PCB land pattern layouts.
Compact Dual-band Reach Xtend TM
2.4-2.5 GHz and 4.9-5.875 GHz Fractus Antennas specializes in enabling effective mobile communications. Using Fractus technology, we design and manufacture optimized antennas to make your wireless devices
Media+ TM UWB (FR01-S1-P-0-107)
Fractus Antennas specializes in enabling effective mobile communications. Using Fractus technology, we design and manufacture optimized antennas to make your wireless devices more competitive. Our mission
Prepared by Qian Ouyang. March 2, 2013
AN075 Rework Process for TQFN Packages Rework Process for TQFN Packages Prepared by Qian Ouyang March 2, 2013 AN075 Rev. 1.1 www.monolithicpower.com 1 ABSTRACT MPS proprietary Thin Quad Flat package No
CeraDiodes. Soldering directions. Date: July 2014
CeraDiodes Soldering directions Date: July 2014 EPCOS AG 2014. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior
2x2 mm LGA Package Guidelines for Printed Circuit Board Design. Figure 1. 2x2 mm LGA package marking information.
2x2 mm LGA Package Guidelines for Printed Circuit Board Design This technical note is intended to provide information about Kionix s 2 x 2 mm LGA packages and guidelines for developing PCB land pattern
APPLICATION NOTE SMT Assembly/Rework Guidelines for MCM-L Packages
APPLICATION NOTE SMT Assembly/Rework Guidelines for MCM-L Packages 101752K July 20, 2015 REVISION HISTORY Revision Date Description A August 2001 Initial Release B January 17, 2002 Revise: Sections 2.1,
TN016. PCB Design Guidelines for 5x5 DFN Sensors. Introduction. Package Marking
PCB Design Guidelines for 5x5 DFN Sensors Introduction This technical note is intended to provide information about Kionix s 5 x 5 mm DFN (non wettable flank, i.e. standard) packages and guidelines for
Selective Soldering for Interconnection Technology Used in Enterprise Communication Apparatuses
Selective Soldering for Interconnection Technology Used in Enterprise Communication Apparatuses Mark Woolley, Wesley Brown, and Dr. Jae Choi Avaya Inc. 1300 W 120 th Avenue Westminster, CO 80234 Abstract:
Slim Reach Xtend TM (FR05-S1-N-0-104) Bluetooth, Zigbee,
Bluetooth, Zigbee, 802.11 b/g/n WLAN Fractus Antennas specializes in enabling effective mobile communications. Using Fractus technology, we design and manufacture optimized antennas to make your wireless
TN019. PCB Design Guidelines for 3x2.5 LGA Sensors Revised. Introduction. Package Marking
PCB Design Guidelines for 3x2.5 LGA Sensors Revised Introduction This technical note is intended to provide information about Kionix s 3 x 2.5 mm LGA packages and guidelines for developing PCB land pattern
DEPARTMENT OF DEFENSE TEST METHOD STANDARD METHOD 210, RESISTANCE TO SOLDERING HEAT
INCH-POUND MIL-STD-202-210 18 April 2015 SUPERSEDING MIL-STD-202G w/change 2 (IN PART) 28 June 2013 (see 6.1) DEPARTMENT OF DEFENSE TEST METHOD STANDARD METHOD 210, RESISTANCE TO SOLDERING HEAT AMSC N/A
EClamp2340C. EMI Filter and ESD Protection for Color LCD Interface PRELIMINARY. PROTECTION PRODUCTS - EMIClamp TM Description.
PROTETION PRODUTS - EMIlamp TM Description The Elamp TM 0 is a low pass filter array with integrated TVS diodes. It is designed to suppress unwanted EMI/RFI signals and provide electrostatic discharge
Compact Reach Xtend TM (FR05-S1-N-0-102) Bluetooth,
Bluetooth, Zigbee, 802.11 b/g/n WLAN Fractus Antennas specializes in enabling effective mobile communications. Using Fractus technology, we design and manufacture optimized antennas to make your wireless
EZConnect TM (FR05-S1-R-0-105) Zigbee, RFID, ISM 868/915
Zigbee, RFID, ISM 868/915 Fractus Antennas specializes in enabling effective mobile communications. Using Fractus technology, we design and manufacture optimized antennas to make your wireless devices
Dual-band Reach Xtend TM (FR05-S1-NO-1-003) GHz
2.4-2.5 GHz and 4.9-5.875 GHz Fractus Antennas specializes in enabling effective mobile communications. Using Fractus technology, we design and manufacture optimized antennas to make your wireless devices
In data sheets and application notes which still contain NXP or Philips Semiconductors references, use the references to Nexperia, as shown below.
Important notice Dear Customer, On 7 February 2017 the former NXP Standard Product business became a new company with the tradename Nexperia. Nexperia is an industry leading supplier of Discrete, Logic
mcube WLCSP Application Note
AN-002 Rev.02 mcube WLCSP Application Note AN-002 Rev.02 mcube, Inc. 1 / 20 AN-002 Rev.02 Guidelines for Printed Circuit Board (PCB) Design and Assembly with mcube Wafer Level Chip Scale Package (WLCSP)
ALPHA EF-6103 Low-Solids, High-Reliability, Pin-Testable, Lead-Free/SnPb Wave Flux
DESCRIPTION ALPHA EF-6103 is an alcohol based flux designed to optimize solderability and reliability. It is formulated for both standard and thicker, high-density PCBs in both Lead-free (standard SAC
(FR05-S1-N-0-110) Bluetooth, Micro Reach Xtend TM. Zigbee, b/g/n WLAN. Micro Reach Xtend TM (FR05-S1-N-0-110)
Micro Reach Xtend TM Zigbee, 82.11 b/g/n WLAN (FR5-S1-N--11) Bluetooth, Fractus Antennas designs, manufactures and commercializes miniature, off-the-shelf antennas for smartphones and general purpose wireless
Recommended Attachment Techniques for ATC Multilayer Chip Capacitors
Recommended Attachment Techniques for ATC Multilayer Chip Capacitors Bulletin No. 201 ATC# 001-119 Rev. M; 8/07 1.0. SCOPE. This document describes the attachment techniques recommended by ATC for ceramic
ENGINEERING PRACTICES STUDY. TITLE: Soldering Heat Testing For Semiconductors. October 27, 2004 STUDY PROJECT FINAL REPORT
ENGINEERING PRACTICES STUDY TITLE: Soldering Heat Testing For Semiconductors October 27, STUDY PROJECT 5961-2911 FINAL REPORT Study Conducted by Alan Barone Prepared by Alan Barone I. OBJECTIVE: The objective
Application Note. Soldering Guidelines for Surface Mount Filters. 1. Introduction. 2. General
Soldering Guidelines for Surface Mount Filters 1. Introduction This Application Guideline is intended to provide general recommendations for handling, mounting and soldering of Surface Mount Filters. These
Application Note. Soldering Guidelines for Module PCB Mounting Rev 13
Application Note Soldering Guidelines for Module PCB Mounting Rev 13 OBJECTIVE The objective of this application note is to provide ANADIGICS customers general guidelines for PCB second level interconnect
Assembly instructions of Dual Flat Lead Package (DFL)
1 (19) TECHNICAL NOTE Assembly instructions of Dual Flat Lead Package (DFL) TABLE OF CONTENTS 1 Objective...3 2 Dual Flat Lead Package (DFL)...3 3 DFL Package Outline and Dimensions...4 4 Tape and reel
HOTBAR REFLOW SOLDERING
HOTBAR REFLOW SOLDERING Content 1. Hotbar Reflow Soldering Introduction 2. Application Types 3. Process Descriptions > Flex to PCB > Wire to PCB 4. Design Guidelines 5. Equipment 6. Troubleshooting Guide
Music Thing Modular SimpleEQ Construction Guide (1206 version)
Music Thing Modular SimpleEQ Construction Guide (1206 version) Page 1 Useful Links The latest version of this doc and BOM can always be found at http://thonk.co.uk/documents/eq/ A build thread on the Muffwiggler
Application Note. Soldering Guidelines for SMPS Multilayer Ceramic Capacitor Assemblies
Application Note AN37-0012 Soldering Guidelines for SMPS Multilayer Ceramic Capacitor Assemblies 1. Introduction With a very low ESR and ESL and the ability to withstand very high levels of di/dt and dv/dt,
Assembling SRD Products Onto Customer s PWBs. murata.com Copyright Murata Manufacturing Co., Ltd. All rights reserved.
Assembling SRD Products Onto Customer s PWBs 1 24 February 2017 1 murata.com Assembling SRD Products Onto Customer s PWBs Considerations/Topics PWB footprint (layout) Solder mask use/layout Type of solder
AN5046 Application note
Application note Printed circuit board assembly recommendations for STMicroelectronics PowerFLAT packages Introduction The PowerFLAT package (5x6) was created to allow a larger die to fit in a standard
What the Designer needs to know
White Paper on soldering QFN packages to electronic assemblies. Brian J. Leach VP of Sales and Marketing AccuSpec Electronics, LLC Defect free QFN Assembly What the Designer needs to know QFN Description:
Technical Note 1 Recommended Soldering Techniques
1 Recommended Soldering Techniques Introduction The soldering process is the means by which electronic components are mechanically and electrically connected into the circuit assembly. Adhering to good
Soldering Techniques NIAGARA COLLEGE TECHNOLOGY DEPT.
Soldering Techniques NIAGARA COLLEGE TECHNOLOGY DEPT. Soldering 101 Soldering is the process of joining two metals together to form an electrically ll and mechanically secure bond using heat and a third
ESD051-1F4. Low clamping single line unidirectional ESD. Datasheet. Features. Application. Description
Datasheet Low clamping single line unidirectional ESD Features ST0201 package Low clamping voltage: -3 V / +9 V (IEC 61000-4-2 contact discharge at 30 ns) Unidirectional diode Low leakage current 0201
RUN mxtend TM (FR01-S4-224) A standard antenna solution
A standard antenna solution for mobile frequency bands Fractus Antennas specializes in enabling effective mobile communications. Using Fractus Antennas technology, we design and manufacture optimized antennas
TRIO mxtend TM (FR01-S4-210) A standard antenna solution for mobile frequency bands
A standard antenna solution for mobile frequency bands Fractus Antennas specializes in enabling effective mobile communications. Using Fractus Antennas technology, we design and manufacture optimized antennas
Position Accuracy Machines for Selective Soldering Fine Pitch Components Gerjan Diepstraten Vitronics Soltec B.V. Oosterhout, Netherlands
As originally published in the IPC APEX EXPO Conference Proceedings. Position Accuracy Machines for Selective Soldering Fine Pitch Components Gerjan Diepstraten Vitronics Soltec B.V. Oosterhout, Netherlands
AR.Drone 2 - Main Board External Antenna Modification Procedure. Document Number: EAM Check back for updates.
Document Number: EAM-20130303-2 Check back for updates. 3/22/2013 NOTE: Along with this mod procedure, you will also need to: 1. Remove the Main Board. Refer to the Main Board Removal Procedure 2. Adapt
mcube LGA Package Application Note
AN-001 Rev.02 mcube LGA Package Application Note AN-001 Rev.02 mcube, Inc. 1 / 21 AN-001 Rev.02 Guidelines for Printed Circuit Board (PCB) Design and Assembly with mcube Land Grid Array (LGA) Package Sensors
SMT Troubleshooting. Typical SMT Problems For additional process solutions, please refer to the AIM website troubleshooting guide
SMT Troubleshooting Typical SMT Problems For additional process solutions, please refer to the AIM website troubleshooting guide Solder Balling Solder Beading Bridging Opens Voiding Tombstoning Unmelted
Ceramic Monoblock Surface Mount Considerations
Introduction Technical Brief AN1016 Ceramic Monoblock Surface Mount Considerations CTS ceramic block filters, like many others in the industry, use a fired-on thick film silver (Ag) metallization. The
Surface Mount Technology Integration of device connection technology in the SMT process Let s connect. White Paper
Surface Mount Technology Integration of device connection technology in the SMT process Let s connect White Paper Surface Mount Technology Integration of device connectivity in the SMT process Today's
QUALITY SEMICONDUCTOR, INC.
Q QUALITY SEMICONDUCTOR, INC. AN-20 Board Assembly Techniques for 0.4mm Pin Pitch Surface Mount Packages Application Note AN-20 The need for higher performance systems continues to push both silicon and
MLPF-WB55-01E GHz low pass filter matched to STM32WB55Cx/Rx. Datasheet. Features. Applications. Description
Datasheet 2.4 GHz low pass filter matched to STM32WB55Cx/Rx Features Top view (pads down) Integrated impedance matching to STM32WB55Cx and STM32WB55Rx LGA footprint compatible 50 Ω nominal impedance on
ESDA24P140-1U3M. High power transient voltage suppressor. Datasheet. Features. Application. Description
Datasheet High power transient voltage suppressor Features Pin # ID 2 Top view Pin 3 bus (bus pin) 3 3 Bottom view 2 Pin, 2* GND (ground pin) *Pin and Pin 2 must be connected together. Low clamping voltage
Surface Mount RF PIN Low Distortion Attenuator Diodes. Technical Data. HSMP-381x Series and HSMP-481x Series. Features
Surface Mount RF PIN Low Distortion Attenuator Diodes Technical Data HSMP-81x Series and HSMP-481x Series Features Diodes Optimized for: Low Distortion Attenuating Microwave Frequency Operation Surface
ECMF2-0730V12M12. Common mode filter with ESD protection for USB2.0 interface. Applications. Description. Features. Complies with following standards
Common mode filter with ESD protection for USB2.0 interface Datasheet - production data V BUS high power TVS diode: V RM = 13.2 V I PP (8/20 µs): 70 A Very low PCB space consumption Thin package: 0.55
Critical Factors in Thru Hole Defects By Ernie Grice Vice President of Sales Kurtz Ersa North America
Critical Factors in Thru Hole Defects By Ernie Grice Vice President of Sales Kurtz Ersa North America Production needs us Soldering Zone Production needs us Thru Hole Soldering Challenges Seite 3 Selective
Recommended Attachment Techniques for ATC Multilayer Chip Capacitors
Recommended Attachment Techniques for ATC Multilayer Chip Capacitors Bulletin No. 201 631-622-4700 sales@atceramics.com +46 8 6800410 sales@atceramics-europe.com +86-755-8366-4318 sales@atceramics-asia.com
TQQ7399 DC 2700 MHz Through Line
Applications General Purpose Wireless RF Bypass Paths Microwave Radio Test & Measurement Scientific Instruments Product Features 6 Pin 3 x 3 mm leadless SMT Package Functional Block Diagram DC 2700 MHz
Plated Through Hole Fill:
Welcome to the EPTAC Webinar Series: Plated Through Hole Fill: Understanding the Process and Assembly Requirements You are connected to our live presentation delivered via the internet. The webinar will
ESDARF02-1BU2CK. Single-line bidirectional ESD protection for high speed interface. Features. Applications. Description
Single-line bidirectional ESD protection for high speed interface Features Datasheet production data Bidirectional device Extra low diode capacitance: 0.2 pf Low leakage current 0201 SMD package size compatible
Application Specification Ultraminiature Bare Poke-in Contact 26FEB2019 REV:A2
Application Specification 114-137190 Ultraminiature Bare Poke-in Contact 26FEB2019 REV:A2 1. INTRODUCTION This specification covers the requirements for application of ultraminiature bare poke-in contacts
Lead Trimming and Hand Soldering Guidelines for VPT DC-DC Converters and Accessory Products
APPLICATION NOTE Lead Trimming and Hand Soldering Guidelines for VPT DC-DC Converters and Accessory Products DC-DC CONVERTERS AND ACCESSORIES AN002-2.0 Page 1 of 7 Contents: Introduction... 3 Lead Trimming...
Is Now Part of To learn more about ON Semiconductor, please visit our website at
Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC
BAT30F4. Small signal Schottky diodes. Description. Features
Small signal Schottky diodes Description Datasheet production data The BAT30F4 uses 30 V Schottky barrier diodes in a 0201 package. This device is intended to be used in smartphones, and is especially
REFLOW TECHNOLOGY. Product Overview
REFLOW TECHNOLOGY Product Overview THR COMPONENT REQUIREMENTS THR Components Components for THR (Through-Hole Reflow) soldering must withstand higher temperatures than those found in standard wave soldering.
!"#$%&'()'*"+,+$&#' *"; Transistor Installation Instructions
INTRODUCTION When inserting high power RF transistor packages into amplifier circuits there are two important objectives. Firstly, removing heat and, secondly, providing a longterm reliable solder joint
AN-5067 PCB Land Pattern Design and Surface Mount Guidelines for MLP Packages
Introduction AN-5067 Fairchild Semiconductor Application Note September 2005 Revised September 2005 PCB Land Pattern Design and Surface Mount Guidelines for MLP Packages The current miniaturization trend
BGA (Ball Grid Array)
BGA (Ball Grid Array) National Semiconductor Application Note 1126 November 2002 Table of Contents Introduction... 2 Package Overview... 3 PBGA (PLASTIC BGA) CONSTRUCTION... 3 TE-PBGA (THERMALLY ENHANCED
ESDA15P60-1U1M. High power transient voltage suppressor
Pin1 Pin2 High power transient voltage suppressor Datasheet - production data Pin2 Pin1 Description The is an unidirectional single line TVS diode designed to protect the power line against EOS and ESD
WLAN/BT/Zigbee/Wi-Fi/Embedded Stamp Metal Antenna
APPLICATION NOTES AN-WF-0146-20180522 2.4/4.9/5.2/5.8 GHz (802.11 a/b/g/n/c + Japan) Applications: Embedded Design Handheld Wireless Headsets Tablets Gateway Access Point Telematics Tracking M2M Healthcare
TECHNICAL INFORMATION
TECHNICAL INFORMATION Super Low Void Solder Paste SE/SS/SSA48-M956-2 [ Contents ] 1. FEATURES...2 2. SPECIFICATIONS...2 3. VISCOSITY VARIATION IN CONTINUAL PRINTING...3 4. PRINTABILITY..............4 5.
Low clamping and low capacitance bidirectional single line ESD protection
Low clamping and low capacitance bidirectional single line ESD protection Datasheet - production data Description The ESDAL5-1BF4 is a bidirectional single line TVS diode designed to protect the data line
CAD Layout Recommendations for the PowerBlox Family
Solved by APPLICATION NOTE ANP4 TM CAD Layout Recommendations for the PowerBlox Family Introduction The Sipex PowerBlox family of parts offers designers a very high power density solution for wide input
ESDZL5-1F4. Low clamping, low capacitance unidirectional single line ESD protection. Description. Features. Applications.
Low clamping, low capacitance unidirectional single line ESD protection Datasheet - production data Description The is a unidirectional single line TS diode designed to protect data lines or other I/O
Initial release of document
This specification covers the requirements for application of SMT Poke In Connectors for use on printed circuit (pc) board based LED strip lighting typically used for sign lighting. The connector accommodates
AND8081/D. Flip Chip CSP Packages APPLICATION NOTE
Flip Chip CSP Packages Prepared by: Denise Thienpont ON Semiconductor Staff Engineer APPLICATION NOTE Introduction to Chip Scale Packaging This application note provides guidelines for the use of Chip
Recommended Land Pattern: [mm]
![Recommended Land Pattern: [mm]](/thumbs/90/103711472.jpg "Recommended Land Pattern: [mm]")
Dimensions: [mm] 0,3 ±0,2 Recommended Land Pattern: [mm] W 0,7 0,7 Electrical Properties: Properties Test conditions Value Unit Tol. Impedance @ 100 MHz Z 100 MHz 470 Ω ±25% Impedance @ 1 GHz Z 1 GHz 600
ESD051-1BF4. 5 V low clamping single line bidirectional ESD protection. Datasheet. Features. Application. Description
Datasheet 5 V low clamping single line bidirectional ESD protection Features ST0201 package Low clamping voltage: 11 V (IEC 61000-4-2 contact discharge at 30 ns) Bidirectional diode Low leakage current
Application Specification Slim WtoB Poke-in Connector
Application Specification 114-137049 Slim WtoB Poke-in Connector 18APR 2016 REV:B 1. INTRODUCTION This specification covers the requirements for application of Slim WtoB Poke in connector for use on lighting
S3X58-M High Reliability Lead Free Solder Paste. Technical Information. Koki no-clean LEAD FREE solder paste.
www.ko-ki.co.jp #52007 Revised on Nov.27, 2014 Koki no-clean LEAD FREE solder paste High Reliability Lead Free Solder Paste S3X58-M500-4 Technical Information O₂ Reflowed 0.5mmP QFP 0603R This product
Pressure Sensor Surface Mount (SMT) Guidelines
Pressure Sensor Surface Mount (SMT) Guidelines A Technical Note 1.0 INTRODUCTION The purpose of this Technical Note is to assist the end-user with pressure sensor (subsequently referred to as sensor )
Application Specification Releasable Poke-in Connector 08JUL 2015 REV:A
Application Specification 114-137055 Releasable Poke-in Connector 08JUL 2015 REV:A 1. INTRODUCTION This specification covers the requirements for application of Releasable Poke-in connector for use on
ESDALC6V1-5M6. 5-line low capacitance Transil arrays for ESD protection ESDALC6V1-5M6. Applications. Description. Features
5-line low capacitance Transil arrays for ESD protection Applications Datasheet - production data Where transient overvoltage protection in ESD sensitive equipment is required, such as: Micro QFN package
Reflow Technology Product Overview
Reflow Technology Product Overview THR COMPONENT REQUIREMENTS THR Components Components for THR (Through-Hole Reflow) soldering must withstand higher temperatures than those found in standard wave soldering.
TN0107 Technical note
Technical note Mounting instructions for STMicroelectronics SLLIMM (small low-loss intelligent molded module) Introduction Small low-loss intelligent molded modules (SLLIMM ) are advanced hybrid power
CF Series AXC5/AXC6. FEATURES 1. Vertical mating type with a 0.8 mm mated height low profile design
For board-to-micro coaxial wire Micro coaxial connectors (Low profile) AC5/AC6 CF Series 2. with strong resistance to various environments provides high contact reliability and facilitates connection work
Applications of Solder Fortification with Preforms
Applications of Solder Fortification with Preforms Carol Gowans Indium Corporation Paul Socha Indium Corporation Ronald C. Lasky, PhD, PE Indium Corporation Dartmouth College ABSTRACT Although many have
Bumping of Silicon Wafers using Enclosed Printhead
Bumping of Silicon Wafers using Enclosed Printhead By James H. Adriance Universal Instruments Corp. SMT Laboratory By Mark A. Whitmore DEK Screen Printers Advanced Technologies Introduction The technology
Module No. # 07 Lecture No. # 35 Vapour phase soldering BGA soldering and De-soldering Repair SMT failures
An Introduction to Electronics Systems Packaging Prof. G. V. Mahesh Department of Electronic Systems Engineering Indian Institute of Science, Bangalore Module No. # 07 Lecture No. # 35 Vapour phase soldering
Recommended Land Pattern: [mm]
![Recommended Land Pattern: [mm]](/thumbs/76/73631372.jpg "Recommended Land Pattern: [mm]")
Dimensions: [mm] 0,5 ±0,3 2,0 ±0,2 Recommended Land Pattern: [mm] W 1,2 WIDE BAND / HIGH SPEED: W = 3,0 HIGH CURRENT: W = 4,0 1,0 Electrical Properties: Properties Test conditions Value Unit Tol. Impedance
Reflow soldering guidelines for surface mounted power modules
Design Note 017 Reflow soldering guidelines for surface mounted power modules Introduction Ericsson surface mounted power modules are adapted to the ever-increasing demands of high manufacturability and