User Manual. LED Dental Scaler, Drill and Polishing unit Eicksonic Plus

Size: px

Start display at page:

Download "User Manual. LED Dental Scaler, Drill and Polishing unit Eicksonic Plus"

Mildred Laureen Wood
5 years ago
Views:

1 User Manual LED Dental Scaler, Drill and Polishing unit Eicksonic Plus

2 Table of Contents Page 1. Scope Device overview and connections Operating the unit Start up scaler Start up drill/polisher Safety Information Conditions of use Maintenance Cleaning and care Troubleshooting Recommended Accessories... 9 Important Note: Please read the operating instructions carefully before starting. The operation must be performed by trained and qualified personnel. Intervention in the appliance must be carried out only by authorized specialist companies. The appliance must not come into contact with liquids and may be operated only with the specified rated voltage ( V). 2/10

1. Scope of delivery: 1 Eick Sonic Plus basic unit (electric component) with a permanently fitted Scaler 1 tartar removal Lace Set (2 x flat, wide, 2 x flat, pointed, 1 x point-like) 1 key to attach

3 1. Scope of delivery: 1 Eick Sonic Plus basic unit (electric component) with a permanently fitted Scaler 1 tartar removal Lace Set (2 x flat, wide, 2 x flat, pointed, 1 x point-like) 1 key to attach the tips on Scaler 1 Micro motor with connection cable and 3-pin DIN connector 1 external power supply 230 V / 24 V AC (alternating current) 1.3 A with connection cable 1 Water connection hose with connector for 3/8 "water line and T-distribution 1 Foot Switch 2. Views of the device and connections: Front: 1. Scaler adjuster (intensity level) for Ultrasonic Scaler 2. Function switch for scaler (ultrasound) or Micro motor operation (drill unit) with foot / hand control 3. Controls for the left / right directions and speed for the drill unit Back: 4. Socket for Micro motor (drill unit) 5. Connection socket for footswitch 6. Socket for power supply 24V AC (alternating current) 1.3 A 7. Amounts of water adjuster for the scaler 8. Connection for water supply. Caution: 0.01 to 0.5 MPa (0.1 to 5.0 bar) Use only clean, filtered or distilled water. 3/10

4 Left: 9. Holder for the Scaler (Ultrasonic dental scaler handpiece) Right: 10. Holder for the micro motor without drill attachment 11. footswitch 4/10

3. Unit into operation : 3.1 Commissioning Scaler with LED lighting 1. Turn the water control knob (7 ) counterclockwise to maximum and the scaler knob (1 ) counterclockwise to the position ( min. ). 2.

5 3. Unit into operation : 3.1 Commissioning Scaler with LED lighting 1. Turn the water control knob (7 ) counterclockwise to maximum and the scaler knob (1 ) counterclockwise to the position ( min. ). 2. Connect the foot switch ( 11) with the socket (5) control unit. 3. Connect the water supply hose to the water input ( 8) and the other end using the supplied connector to a water source ( Line, angle valve or water pressure tank) to. 4. Turn a scaler tip in the scaler handpiece and pull the top with the supplied key firmly. 5. Connect the device-side power cable to the unit to the jack ( 6) and the Power adapter to the power grid. 6. Set the desired intensity level using the adjuster ( 1) and start or stop the function with the foot switch. 7. Correct the desired amount of water with the adjusters (7 ) on the back. Regularly check your scaler tips using the supplied Picture for wear. In case of heavy wear urgently replace the tips. 3.2 Commissioning Drill/Polisher 1. Check if the power is off (the adjuster (2) and (3) to "0"). 2. Connect the Micro motor with the socket (4) of the control unit. 3. Unscrew the dust cap from the micro engine and plug the Handpiece (not included) on. Product No.: angle or straight handpiece Insert the drill bit (not included in scope of supply) in the appropriate handpiece. To lock the drills please refer to the operating instructions of the handpieces. Check the correct position by turning the hand piece or gently pulling on the drill. 5. Turn the mode selector switch (2) to micromotor foot operation or manual operation 6. Use the adjuster (3) the desired direction of rotation and adjust the desired rotational speed "min -. maximum." one. 7. With the foot switch (11) to start the engine or turn it off. 5/10

Hold the straight handpiece down during operation so that no water and dirt runs in the micro motor. The micro motor is not internally waterproof.

6 Hold the straight handpiece down during operation so that no water and dirt runs in the micro motor. The micro motor is not internally waterproof. IMPORTANT: Before you replace the drill, turn off the power. Prefs (2) to "0" and the speed control "Micromotor" (3) to "0" provide. 4. Safety: 1. Keep the unit away from children. 2. The device may only be used in accordance with its intended purpose. 3. In case of a defective cable, the device must not be operated. 4. Please follow the care instructions in the user manual the handpieces. 5. If you want to change the drill bit, turn the power off. 6. The scaler tip has to vibrate / the drill has to rotate before it can be placed on a tooth. 7. Wear eye protection during work and provide for an adequate suction. 8. Do not Clean or oil the handpiece during operation. 9. Leave after operation a drill or the supplied dummy pin in Handpiece clamped. 5. Operating conditions: Temperature: +10 C ~ +40 C Humidity: 30% ~ 75% Air pressure: 700 ~ 1060 hpa (0.7 to 1.06 bar) Operate handpiece only with the supplied foot pedal defects drill cause imbalance and lead to premature wear of the bearings 6. Maintenance: The drill/poliosher is maintenance-free. Only the carbon brushes in the motor Micro should be replaced annually. Please send your Micro motor to us for maintenance. 7. Cleaning and care: Micro motor and handpieces It is imperative the handpieces be thoroughly cleaned and oiled after each. (Suggested Spray: Article and adapter million). 6/10

7 Oil the Micro Motors Oil the straight handpiece Oiling the angle handpiece outside Micro motor after the oil with the head hanging down in the holder (10) Demo days before and after the installation Oiling the angle handpiece inside Oiling the angle handpiece inside Store the Handpieces separately after oiling Do not Fit. 7/10

Scaler with LED lighting Remove the scaler tip with the including key ring.

Remove the trim ring on the handle of the Scalerhandstücks and clean with alcohol.

disinfection (135 C, 12:22 Mpa) 8. Troubleshooting: 1. Check the fit of the power plug 2.

8 Scaler with LED lighting Remove the scaler tip with the including key ring. Remove the screw and clean the shaft with alcohol. Remove the trim ring on the handle of the Scalerhandstücks and clean with alcohol. Disconnect the main handpiece from the scaler and autoclave under high temperature and pressure disinfection (135 C, 12:22 Mpa) 8. Troubleshooting: 1. Check the fit of the power plug 2. Check the power cable of the handpiece 3. Check the fuse 4. Check whether the device is switched on 5. Check the carbon brushes are worn and if they need to be replaced (see Maintenance) 8/10

9 9. Recommended Accessories: Angle handpiece Straight handpiece Replacement Tips for Tartar device Plastic polishing attachments with rubber polishing cup Spray for rotating Instrument Tooth polish Plug adapters for use with spray /10

10 GERMANY EICKEMEYER KG Eltastraße Tuttlingen T F E info@eickemeyer.de ITALY EICKEMEYER S.R.L. Via G. Verdi, Montesilvano (PE) T F E info@eickemeyer.it CANADA EICKEMEYER Inc. 250 Briarhill Dr. Stratford, Ont. Canada N5A 7S2 T F E info@eickemeyer.com DENMARK EICKEMEYER ApS Lysbjergvej 6, Hammelev 6500 Vojens T F E info@eickemeyer.dk NETHERLANDS EICKEMEYER B.V. Bedrijventerrein Pavijen-West Bellweg BJ Culemborg T F E info@eickemeyer.nl POLAND EICKEMEYER Sp. z o.o. Al. Jana Pawła II Warszawa T F E info@eickemeyer.pl SWITZERLAND EICKEMEYER AG Sandgrube Appenzell T F E info@eickemeyer.ch UNITED KINGDOM EICKEMEYER Ltd. 3 Windmill Business Village Brooklands Close Sunbury-on-Thames Surrey, TW16 7DY T F E info@eickemeyer.co.uk

EICKEMEYER INFUSION WARMER

EICKEMEYER INFUSION WARMER MANUAL Art. No. 402091 TELEPHONE +49 7461 96580 0 www.eickemeyer.com Contents 1 Introduction... 3 2 Working Principle... 3 3 Main Technical Specifications... 3 4 Composition