Technical Graphics Ordinary Level Section A (120 marks)
|
|
- Alfred Rose
- 5 years ago
- Views:
Transcription
1 Coimisiún na Scrúduithe Stáit State Examinations Commission S60A Junior Certificate Examination, 2012 Technical Graphics Ordinary Level Section A (120 marks) Monday, 18 June Morning 9:30-12:00 Centre Number (a) (b) (c) (d) (e) Instructions Answer any ten questions in the spaces provided. All questions carry equal marks. Construction lines must be clearly shown. All measurements are in millimetres. This booklet must be handed up at the end of the examination. Write your examination number in the box provided below and on all other pages used. Examination Number: Question Section A TOTAL GRADE Mark Section A - Page 1 of 6
2 SECTION A. Answer any ten questions. All questions carry equal marks. 1 Shown is the incomplete elevation and incomplete end view of a writing desk. Also shown is a 3D graphic of the desk. Insert the missing lines in both the elevation and the end view. 2 In the space provided, make a freehand sketch of the wastepaper bin shown. Colour or shade the completed sketch. 3 List one advantage and one disadvantage of a tablet computer, as shown. Advantage: Disadvantage: Section A - Page 2 of 6
3 4 Fig.1 shows a design for a speaker inscribed in the square ABCD. Draw an enlarged design of the speaker in the given square ABCD in Fig. 2. Fig. 1 Fig. 2 5 Fig.1 shows the design of a helmet based on a semi-ellipse with an attached safety shield. The line PL is a tangent to the semi-ellipse at P. Locate the focal points of the semi-ellipse in Fig.2 and complete the design by drawing the tangent PL. P Fig. 1 Fig. 2 6 The elevation and plan of a garden seat are shown. Complete the given 3D sketch of the seat on the grid provided. Colour or shade the completed sketch. Section A - Page 3 of 6
4 7 The design of a sports trophy is shown. Write down the area of the trophy in square centimetres - cm 2. 1 square = 1 cm 2 Area of the trophy: cm 2. 8 Using the scale provided, measure and write down the dimensions A and B of the clothes stand shown. A: B: 9 The figure shows a set of blocks. Draw, in the space provided, an elevation of the blocks in the direction of the arrow. Section A - Page 4 of 6
5 10 The drawing shows the design of a light bulb. Show clearly all the points of contact between the arcs. 11 List the CAD commands used to produce the figures A to B and B to C. A B C Commands: A B B C 12 The graphic shows a small table lamp. Draw the shadow cast by the base of the lamp shown in Fig.1 when the direction of light is parallel to the arrow. Fig.1 Section A - Page 5 of 6
6 13 Fig.1 shows the design of a road sign based on a circle and a regular hexagon. Complete Fig. 2 to show the design of the road sign. Fig. 1 Fig The figure shows an incomplete perspective drawing of a toaster. A small 3D graphic of the toaster is also shown. Complete the perspective drawing. 15 The diagram shows a barrier at the entrance to a car park. Rotate the arm M in the direction of the arrow through 45º about the point P and complete the drawing of the arm in the rotated position. Section A - Page 6 of 6
7 Blank Page
8 Blank Page
9 Coimisiún na Scrúduithe Stáit State Examinations Commission S60B Junior Certificate Examination, 2012 Technical Graphics Ordinary Level Section B (280 marks) Monday, 18 June Morning 9:30-12:00 Instructions (a) (b) (c) (d) Answer any four questions. All questions carry equal marks. The number of the question must be distinctly marked by the side of each answer. Work on one side of the answer paper only. Write your examination number on each sheet of paper used. Section B - Page 1 of 4
10 SECTION B. Answer any four questions. All questions carry equal marks. 1 The figure shows a design for a letterbox. Draw: (a) (b) (c) An elevation in the direction of arrow A. An end elevation in the direction of arrow B. Insert any four dimensions. Note: The back surface S is vertical as shown. 2 The figure shows the design of a logo for a locksmith. The curve ABC is a semi-ellipse. AC is the major axis, OB is half the minor axis and is 50 mm long as shown. Draw the given logo showing clearly all construction lines. Section B - Page 2 of 4
11 3 The figure shows a design for a cup-holder. Also shown is a 3D graphic of the cup-holder. Draw: (a) (b) (c) An elevation in the direction of arrow A. A plan projected from the elevation. The complete surface development of the cup-holder. 4 The figure shows the elevation and plan of the initials for the Forest Stewardship Council (FSC). The Forest Stewardship Council promotes the responsible management of the world s forests. The grid in elevation is made up of 15 mm squares and the thickness in plan is 10 mm. Draw one of the following views: (a) An isometric view of the initials or (b) An oblique view of the initials. Note: The solution must be presented on standard drawing paper. Section B - Page 3 of 4
12 5 The given figure shows the design of a logo for a television channel - Channel 1. Also shown is a small 3D graphic of the logo. Draw the given logo and then locate the points A, A1, A2, A3 and O as shown. Find the image of the given logo under the following transformations: (a) From point A to A1 by an axial symmetry in the line A2-A3; (b) From point A1 to A2 by a translation; (c) From point A2 to A3 by a central symmetry in the point O. 6 The figure shows the design of a logo to indicate that an area is safe for swimming. Draw the semi-circle of radius 100 mm as shown and then complete the given logo. The line LM is a tangent to the circle from L. Show all construction lines, tangents and points of contact. Section B - Page 4 of 4
Technical Graphics Higher Level
Coimisiún na Scrúduithe Stáit State Examinations Commission Junior Certificate Examination 2005 Technical Graphics Higher Level Marking Scheme Sections A and B Section A Q1. 12 Four diagrams, 3 marks for
More informationA JUNIOR CERTIFICATE EXAMINATION, 2003
AN ROINN OIDEACHAIS AGUS EOLAÍOCHTA S61A A JUNIOR CERTIFICATE EXAMINATION, 2003 TECHNICAL GRAPHICS HIGHER LEVEL THURSDAY 12 JUNE MORNING, 9:30-12:30 TOTAL MARKS 400 (Sections A and B) Examination Number
More informationJUNIOR CERTIFICATE 2009 MARKING SCHEME TECHNICAL GRAPHICS HIGHER LEVEL
. JUNIOR CERTIFICATE 2009 MARKING SCHEME TECHNICAL GRAPHICS HIGHER LEVEL Sections A and B Section A any ten questions from this section Q1 12 Four diagrams, 3 marks for each correct label. Q2 12 2 marks
More informationCoimisiún na Scrúduithe Stáit State Examinations Commission. Junior Certificate Marking Scheme. Technical Graphics.
Coimisiún na Scrúduithe Stáit State Examinations Commission Junior Certificate 2013 Marking Scheme Technical Graphics Higher Level Note to teachers and students on the use of published marking schemes
More informationTechnical Drawing Paper 1 - Higher Level (Plane and Solid Geometry)
Coimisiún na Scrúduithe Stáit State Examinations Commission 2008. M81 Leaving Certificate Examination 2008 Technical Drawing Paper 1 - Higher Level (Plane and Solid Geometry) (200 Marks) Friday 13 June
More informationCoimisiún na Scrúduithe Stáit State Examinations Commission
2009. M26 Coimisiún na Scrúduithe Stáit State Examinations Commission LEAVING CERTIFICATE EXAMINATION, 2009 MATHEMATICS FOUNDATION LEVEL PAPER 2 ( 300 marks ) MONDAY, 8 JUNE MORNING, 9:30 to 12:00 Attempt
More informationCoimisiún na Scrúduithe Stáit State Examinations Commission
2008. M26 Coimisiún na Scrúduithe Stáit State Examinations Commission LEAVING CERTIFICATE EXAMINATION 2008 MATHEMATICS FOUNDATION LEVEL PAPER 2 ( 300 marks ) MONDAY, 9 JUNE MORNING, 9:30 to 12:00 Attempt
More informationJUNIOR CERTIFICATE 2008 MARKING SCHEME TECHNICAL GRAPHICS HIGHER LEVEL
JUNIOR CERTIFICATE 2008 MARKING SCHEME TECHNICAL GRAPHICS HIGHER LEVEL Sections A and B Section A - any ten questions from this Section Q1 12 Four diagrams, 3 marks for each correct label. Q2 12 3 height
More informationDesign & Communication Graphics Higher Level Section A (60 marks)
Coimisiún na Scrúduithe Stáit State Examinations Commission 2011. M81A Leaving Certificate Examination, 2011 Design & Communication Graphics Higher Level Section A (60 marks) Friday, 17 June Afternoon,
More informationMaterials Technology Wood Higher Level Section A (40 Marks)
Coimisiún na Scrúduithe Stáit State Examinations Commission S54A Junior Certificate Examination 2006 Materials Technology Wood Higher Level Section A (40 Marks) Monday 19 June Afternoon, 2.00-4.00 Instructions
More informationUNIVERSITY OF CAMBRIDGE INTERNATIONAL EXAMINATIONS International General Certificate of Secondary Education
UNIVERSITY OF CAMBRIDGE INTERNATIONAL EXAMINATIONS International General Certificate of Secondary Education www.xtremepapers.com DESIGN AND TECHNOLOGY DESIGN AND COMMUNICATION 0446/02 Paper 2 Graphic Products
More informationDesign & Communication Graphics Ordinary Level Sections B and C (180 marks)
Coimisiún na Scrúduithe Stáit State Examinations Commission 2013. M80BC Leaving Certificate Examination, 2013 Design & Communication Graphics Ordinary Level Sections B and C (180 marks) Wednesday, 19 June
More informationDesign & Communication Graphics Higher Level Sections B and C (180 Marks)
Coimisiún na Scrúduithe Stáit State Examinations Commission 2009. M81BC Leaving Certificate Examination, 2009 Design & Communication Graphics Higher Level Sections B and C (180 Marks) Friday, 12 June Afternoon,
More informationMaterials Technology (Wood) Ordinary Level Section A (40 Marks)
Coimisiún na Scrúduithe Stáit State Examinations Commission 2012. S53 Junior Certificate Examination 2012 Materials Technology (Wood) Ordinary Level Section (40 Marks) Monday 18 June fternoon, 2.00-4.00
More informationVocational Specialism Graphics and Construction Studies (240 marks)
Coimisiún na Scrúduithe Stáit State Examinations Commission 2013. AP 9.10 Leaving Certificate Applied, 2013 Vocational Specialism Graphics and Construction Studies (240 marks) Tuesday, 11 th June, Morning,
More informationDesign & Communication Graphics Higher Level Sections B and C (180 marks)
Coimisiún na Scrúduithe Stáit State Examinations Commission 2016. M81BC Leaving Certificate Examination, 2016 Design & Communication Graphics Higher Level Sections B and C (180 marks) Wednesday, 22 June
More informationCoimisiún na Scrúduithe Stáit State Examinations Commission. Junior Certificate Examination Mathematics
2018. S33 Coimisiún na Scrúduithe Stáit State Examinations Commission Junior Certificate Examination 2018 Mathematics Paper 2 Ordinary Level Monday 11 June Morning 9:30 to 11:30 300 marks Examination Number
More information2. Here are some triangles. (a) Write down the letter of the triangle that is. right-angled, ... (ii) isosceles. ... (2)
Topic 8 Shapes 2. Here are some triangles. A B C D F E G (a) Write down the letter of the triangle that is (i) right-angled,... (ii) isosceles.... (2) Two of the triangles are congruent. (b) Write down
More informationMathematics (Project Maths Phase 1)
2012. M128 Coimisiún na Scrúduithe Stáit State Examinations Commission Leaving Certificate Examination, 2012 Mathematics (Project Maths Phase 1) Paper 2 Ordinary Level Monday 11 June Morning 9:30 12:00
More informationDesign & Communication Graphics Ordinary Level Sections B and C (180 marks)
Coimisiún na Scrúduithe Stáit State Examinations Commission 2010. M80BC Leaving Certificate Examination, 2010 Design & Communication Graphics Ordinary Level Sections B and C (180 marks) Friday, 18 June
More informationDesign & Communication Graphics Higher Level Sections B and C (180 marks)
Coimisiún na Scrúduithe Stáit State Examinations Commission 202. M8BC Leaving Certificate Examination, 202 Design & Communication Graphics Higher Level Sections B and C (80 marks) Wednesday, 20 June Afternoon,
More informationCoimisiún na Scrúduithe Stáit State Examinations Commission. Leaving Certificate Marking Scheme. Design and Communication Graphics
Coimisiún na Scrúduithe Stáit State Examinations Commission Leaving Certificate 2016 Marking Scheme Design and Communication Graphics Ordinary Level Note to teachers and students on the use of published
More informationLeaving Certificate 201
Coimisiún na Scrúduithe Stáit State Examinations Commission Leaving Certificate 201 Marking Scheme Design and Communication Graphics Ordinary Level Note to teachers and students on the use of published
More informationMathematics (Project Maths Phase 2)
2014. S233 Coimisiún na Scrúduithe Stáit State Examinations Commission Junior Certificate Examination 2014 Mathematics (Project Maths Phase 2) Paper 2 Ordinary Level Monday 9 June Morning, 9:30 to 11:30
More informationCoimisiún na Scrúduithe Stáit State Examinations Commission. Junior Certificate Examination Mathematics. Paper 2 Higher Level
2016. S35 Coimisiún na Scrúduithe Stáit State Examinations Commission Junior Certificate Examination 2016 Mathematics Paper 2 Higher Level Monday 13 June Morning 9:30 to 12:00 300 marks Examination number
More information2 nd Year TG Portfolio
2 nd Year TG Portfolio 2016-2017 Inside you will find: What is required of you for each portfolio sheet. An assessment rubric for each portfolio sheet to guide you towards maximum learning. You will need
More informationProduction drawing Diagram. a) I am a freehand drawing that follows technical drawing standards.
THE TECHNOLOGICAL WORLD Graphical language STUDENT BOOK Ch. 11, pp. 336 342 Basic lines, geometric lines, sketches 1. In technology, the two most widely used types of technical drawings are: a) sketch
More informationDesign & Communication Graphics
L.84/85 Design & Communication Graphics Marking Scheme Ordinary Pg. 3 Higher Pg. 12 2013 L.84/85_MS 1/20 2013 L.84/85_MS 2/20 SECTION A - Core - Answer Any Three of the questions on this A3 sheet A-1.
More informationCoimisiún na Scrúduithe Stáit State Examinations Commission. Junior Certificate Marking Scheme. Technology. Ordinary Level
Coimisiún na Scrúduithe Stáit State Examinations Commission Junior Certificate 0 Marking Scheme Technology Ordinary Level Coimisiún na Scrúduithe Stáit State Examinations Commission Junior Certificate
More informationActivity 5.2 Making Sketches in CAD
Activity 5.2 Making Sketches in CAD Introduction It would be great if computer systems were advanced enough to take a mental image of an object, such as the thought of a sports car, and instantly generate
More informationLeaving Certificate 2014
Coimisiún na Scrúduithe Stáit State Examinations Commission Leaving Certificate 2014 Marking Scheme Design and Communication Graphics Higher Level Note to teachers and students on the use of published
More informationMathematics (Project Maths)
010. M16 Coimisiún na Scrúduithe Stáit State Examinations Commission Leaving Certificate Examination Mathematics (Project Maths) Paper Foundation Level Monday 14 June Morning 9:30 1:00 300 marks Examination
More informationMaterials Technology - Wood
Coimisiún na Scrúduithe Stáit State Examinations Commission 2013. S54A Junior Certificate Examination, 2013 Materials Technology - Wood Higher Level Section A (40 marks) Monday, 17 June Afternoon, 2:00-4:00
More informationENGINEERING GRAPHICS 1E9
Lecture 3 Monday, 15 December 2014 1 ENGINEERING GRAPHICS 1E9 Lecture 3: Isometric Projections Lecture 3 Monday, 15 December 2014 2 What is ISOMETRIC? It is a method of producing pictorial view of an object
More informationTechnical Drawing Paper II(A) Higher Level (Engineering Applications)
Coimisiún na Scrúduithe Stáit State Examinations Commission 2007. M84 Leaving Certificate Examination 2007 Technical Drawing Paper II(A) Higher Level (Engineering Applications) (200 Marks) Friday 15 June
More informationMathematics (Project Maths Phase 2)
2011. M228 Coimisiún na Scrúduithe Stáit State Examinations Commission Leaving Certificate Examination, 2011 Mathematics (Project Maths Phase 2) Paper 2 Ordinary Level Monday 13 June Morning 9:30 12:00
More informationChapter 1 Overview of an Engineering Drawing
Chapter 1 Overview of an Engineering Drawing TOPICS Graphics language Engineering drawing Projection methods Orthographic projection Drawing standards TOPICS Traditional Drawing Tools Lettering Freehand
More informationDesign & Communication Graphics Higher Level Section A (60 Marks)
1 L.85A Pre-Leaving Certificate Examination, 2011 Design & Communication Graphics Higher Level Section A (60 Marks) Time: 3 Hours This examination is divided into three sections: SECTION A SECTION B SECTION
More information11/12/2015 CHAPTER 7. Axonometric Drawings (cont.) Axonometric Drawings (cont.) Isometric Projections (cont.) 1) Axonometric Drawings
CHAPTER 7 1) Axonometric Drawings 1) Introduction Isometric & Oblique Projection Axonometric projection is a parallel projection technique used to create a pictorial drawing of an object by rotating the
More informationCoimisiún na Scrúduithe Stáit State Examinations Commission. Leaving Certificate Marking Scheme. Design and Communication Graphics.
Coimisiún na Scrúduithe Stáit State Examinations Commission Leaving Certificate 2016 Marking Scheme Design and Communication Graphics Higher Level Note to teachers and students on the use of published
More informationApplications of Mathematics (Linked Pair)
Centre Number Surname Candidate Number For Examiner s Use Other Names Candidate Signature Examiner s Initials Pages Mark General Certificate of Secondary Education Foundation Tier June 2015 Applications
More informationMathematics (Project Maths Phase 2)
2013. M228 Coimisiún na Scrúduithe Stáit State Examinations Commission Leaving Certificate Examination 2013 Mathematics (Project Maths Phase 2) Paper 2 Ordinary Level Monday 10 June Morning 9:30 12:00
More informationDesign & Communication Graphics Higher Level Section A (60 Marks)
M.85A ªM.858 Leaving Certificate Examination, 2009 Design & Communication Graphics Higher Level Section A (60 Marks) Time: 3 Hours This examination is divided into three sections: SECTION A SECTION B SECTION
More informationDesign & Communication Graphics Higher Level Section A (60 marks)
1 L.85A Pre-Leaving Certificate Examination, 2012 Design & Communication Graphics Higher Level Section A (60 marks) Time: 3 Hours This examination is divided into three sections: SECTION A SECTION B SECTION
More informationDesign & Communication Graphics Ordinary Level Section A (60 Marks)
M.84A ªM.844 Leaving Certificate Examination, 2009 Design & Communication Graphics Ordinary Level Section A (60 Marks) Time: 3 Hours This examination is divided into three sections: SECTION A SECTION B
More informationMathematics (Project Maths)
2010. M128 S Coimisiún na Scrúduithe Stáit State Examinations Commission Leaving Certificate Examination Sample Paper Mathematics (Project Maths) Paper 2 Ordinary Level Time: 2 hours, 30 minutes 300 marks
More informationUnit 4: Geometric Construction (Chapter4: Geometry For Modeling and Design)
Unit 4: Geometric Construction (Chapter4: Geometry For Modeling and Design) DFTG-1305 Technical Drafting Instructor: Jimmy Nhan OBJECTIVES 1. Identify and specify basic geometric elements and primitive
More informationDesign & Communication Graphics Higher Level Section A (60 marks)
1 L.85A Pre-Leaving Certificate Examination, 2015 Design & Communication Graphics Higher Level Section A (60 marks) Time: 3 Hours This examination is divided into three sections: SECTION A SECTION B SECTION
More informationORDINARY LEVEL PAST PAPERS
ORDINARY LEVEL PAST PAPERS UNEB S4 1982 SECTION I PLANE GEOMETRY 1. (a) Construct a diagonal scale of 40mm to 10mm to read up to 20mm by 0.02mm. (b) Indicate on your scale the following readings. (i) 14.8mm.
More informationENGINEERING DRAWING SKKK 1021 ISOMETRIC DRAWING. Agus Arsad, Azizul Azri Bin Mustaffa 10/2/2012 1
ENGINEERING DRAWING SKKK 1021 ISOMETRIC DRAWING Agus Arsad, Azizul Azri Bin Mustaffa 10/2/2012 1 LEARNING OUTCOMES ISOMETRIC DRAWING It is expected that students will be able to: Understand the significance
More information*X033/12/01* X033/12/01 HIGHER STAPLE HERE NATIONAL QUALIFICATIONS. 8 Orthographic drawings are in third angle projection.
Question 2 3 4 Section A Total 7a 7b 8 9 0 EITHER OR 2 Section B Total Total Marks A + B Marks STAPLE HERE FOR OFFICIAL USE 033/2/0 NATIONAL QUALIFICATIONS 204 THURSDAY, 8 MAY.00 PM 4.00 PM GRAPHIC COMMUNICATION
More information(Chapter 15) (Visualising Solid Shapes) (Class VII) Question 1: Exercise 15.1 Identify the nets which can be used to make cubes (cut out copies of the nets and try it): Answer 1: Cube s nets are (ii),
More informationNCERT Solutions Class 7 Mathematics Visualising Solid Shapes Chapter: 15
Q.1) Exercise 15.1 NCERT Solutions Class 7 Mathematics Visualising Solid Shapes Chapter: 15 Identify the nets which can be used to make cubes (cut out copies of the nets and try it): Q.2) Sol.2) Cube s
More informationtechnical drawing
technical drawing school of art, design and architecture nust spring 2011 http://www.youtube.com/watch?v=q6mk9hpxwvo http://www.youtube.com/watch?v=bnu2gb7w4qs Objective abstraction - axonometric view
More informationCoimisiún na Scrúduithe Stáit State Examinations Commission. Leaving Certificate Examination
Coimisiún na Scrúduithe Stáit State Examinations Commission 2009. M103A (S) Leaving Certificate Examination Technology Ordinary Level Sample Paper Duration 2:00 hours There are three Sections in this paper.
More informationISOMETRIC PROJECTION. Contents. Isometric Scale. Construction of Isometric Scale. Methods to draw isometric projections/isometric views
ISOMETRIC PROJECTION Contents Introduction Principle of Isometric Projection Isometric Scale Construction of Isometric Scale Isometric View (Isometric Drawings) Methods to draw isometric projections/isometric
More informationMath 9 - Similar and Transformations Unit Assignment
Math 9 - Similar and Transformations Unit Assignment Multiple Choice Identify the choice that best completes the statement or answers the question. 1. Determine the scale factor for this scale diagram.
More informationCDT: DESIGN AND COMMUNICATION
CDT: DESIGN AND COMMUNICATION Paper 7048/01 Structured Key message Whilst many excellent answers were seen, the following were considered to be areas where improvement could be made: the correct positioning
More informationUNIVERSITY OF MALTA SECONDARY EDUCATION CERTIFICATE SEC GRAPHICAL COMMUNICATION. May 2016 EXAMINERS' REPORT MATRICULATION AND SECONDARY EDUCATION
UNIVERSITY OF MALTA SECONDARY EDUCATION CERTIFICATE SEC GRAPHICAL COMMUNICATION May 2016 EXAMINERS' REPORT MATRICULATION AND SECONDARY EDUCATION CERTIFICATE EXAMINATIONS BOARD 1 SEC Graphical Communication
More informationCOURSE: INTRODUCTION TO CAD GRADES: UNIT: Measurement
UNIT: Measurement - Students will demonstrate correctness in measuring using various scales and instruments. Demonstrate the various marks that make up a ruler including 1/16, 1/8, ¼ and ½. Assessment
More information3 In the diagram below, the vertices of DEF are the midpoints of the sides of equilateral triangle ABC, and the perimeter of ABC is 36 cm.
1 In the diagram below, ABC XYZ. 3 In the diagram below, the vertices of DEF are the midpoints of the sides of equilateral triangle ABC, and the perimeter of ABC is 36 cm. Which two statements identify
More informationMathematics (Project Maths Phase 2)
013. M7 Coimisiún na Scrúduithe Stáit State Examinations Commission Leaving Certificate Examination 013 Mathematics (Project Maths Phase ) Paper 1 Ordinary Level Friday 7 June Afternoon :00 4:30 300 marks
More informationGraphic Communication Prelim
H Date February 05 Duration hours Graphic Communication Prelim Name Number of seat Total marks 70 Attempt ALL questions. Write your answers clearly in the spaces provided in this booklet. All dimensions
More informationSHAPE level 2 questions. 1. Match each shape to its name. One is done for you. 1 mark. International School of Madrid 1
SHAPE level 2 questions 1. Match each shape to its name. One is done for you. International School of Madrid 1 2. Write each word in the correct box. faces edges vertices 3. Here is half of a symmetrical
More informationMathematics (Project Maths Phase 2)
2013.M227 S Coimisiún na Scrúduithe Stáit State Examinations Commission Leaving Certificate Examination 2013 Sample Paper Mathematics (Project Maths Phase 2) Paper 1 Ordinary Level Time: 2 hours, 30 minutes
More informationChange of position method:-
Projections of Planes PROJECTIONS OF PLANES A plane is a two dimensional object having length and breadth only. Thickness is negligible. Types of planes 1. Perpendicular plane which have their surface
More informationProduct design: Communicating your design proposals
Product design: Communicating your design proposals In the world of business and industry design proposals can only be turned into saleable products if the designers communicate their proposals effectively.
More information2010 Academic Challenge
2010 Academic Challenge ENGINEERING GRAPHICS TEST STATE FINALS This Test Consists of 40 Questions Engineering Graphics Test Production Team Ryan K. Brown, Illinois State University Author/Team Leader Jacob
More informationChapter 5 Pictorial Projection
Chapter 5 Pictorial Projection Objectives After completing this chapter, the students will be able to Create freehand sketches using the correct sketching techniques. Explainthe difference between axonometric
More informationMathematics (Project Maths Phase 3)
2013. S333 Coimisiún na Scrúduithe Stáit State Examinations Commission Junior Certificate Examination, 2013 Mathematics (Project Maths Phase 3) Paper 2 Ordinary Level Monday 10 June Morning 9.30 to 11.30
More informationENGINEERING GRAPHICS
ENGINEERING GRAPHICS Time allowed : 3 hours Maximum Marks : 70 Note : (ii) Attempt all the questions. Use both sides of the drawing sheet, if necessary. (iii) All dimensions are in millimetres. (iv) Missing
More informationChapter 5 Pictorial sketching
Chapter 5 Pictorial sketching Contents Freehand sketching techniques Pictorial projections - Axonometric - Oblique Isometric projection vs isometric sketch Isometric sketch from an orthographic views Isometric
More informationTo start a new drawing Select File New then from the dialog box, which appears select Normal.dft followed by OK.
Draft Tutorial This tutorial provides step-by-step instructions for the detailing of a drawing of the anchor block shown opposite. As you create this drawing, you will use the following drafting techniques:
More informationStandards of Learning Guided Practice Suggestions. For use with the Mathematics Tools Practice in TestNav TM 8
Standards of Learning Guided Practice Suggestions For use with the Mathematics Tools Practice in TestNav TM 8 Table of Contents Change Log... 2 Introduction to TestNav TM 8: MC/TEI Document... 3 Guided
More informationUNIVERSITY OF MALTA SECONDARY EDUCATION CERTIFICATE SEC GRAPHICAL COMMUNICATION. May 2014 EXAMINERS REPORT
UNIVERSITY OF MALTA SECONDARY EDUCATION CERTIFICATE SEC GRAPHICAL COMMUNICATION May 2014 EXAMINERS REPORT MATRICULATION AND SECONDARY EDUCATION CERTIFICATE EXAMINATIONS BOARD SEC Graphical Communication
More informationCoimisiún na Scrúduithe Stáit State Examinations Commission. Leaving Certificate Examination Mathematics. Foundation Level
2016. M25 Coimisiún na Scrúduithe Stáit State Examinations Commission Leaving Certificate Examination 2016 Mathematics Friday 10 June Afternoon 2:00 4:30 300 marks Running total Examination number Centre
More informationENGINEERING GRAPHICS
ENGINEERING GRAPHICS Course Structure Units Topics Marks Unit I Plane Geometry 16 1 Lines, angles and rectilinear figures 2 Circles and tangents 3 Special curves: ellipse, parabola, involute, cycloid.
More informationMathematics (Project Maths Phase 3)
2013. S332 S Coimisiún na Scrúduithe Stáit State Examinations Commission Junior Certificate Examination, 2013 Sample Paper Mathematics (Project Maths Phase 3) Paper 1 Ordinary Level Time: 2 hours 300 marks
More informationVocational Specialism - Technology (240 Marks)
2015. AP9.8 Coimisiún na Scrúduithe Stáit State Examinations Commission Leaving Certificate Applied, 2015 Vocational Specialism - Technology (240 Marks) General Directions: Wednesday 10 June, Afternoon
More information2004 Academic Challenge
2004 Academic Challenge ENGINEERING GRAPHICS TEST - REGIONAL Engineering Graphics Test Production Team Ryan Brown, Illinois State University Author/Team Coordinator Kevin Devine, Illinois State University
More informationCoimisiún na Scrúduithe Stáit State Examinations Commission. Leaving Certificate Examination, Answer these questions in the answerbook provided.
Coimisiún na Scrúduithe Stáit State Examinations Commission 2014. M103 BC Leaving Certificate Examination, 2014 Technology Ordinary Level Friday, 20 June Afternoon, 2:00-4:00 Section B - Core Answer both
More informationSpatula. Spatula SW 2015 Design & Communication Graphics Page 1
Spatula Introduction: The model shown in the picture is made of three parts, - the base, the washer and the handle. The base requires the use of Spline and Style Spline command, Slot command and Mirror
More informationCoimisiún na Scrúduithe Stáit. State Examinations Commission. Leaving Certificate Examination 2010
Coimisiún na Scrúduithe Stáit State Examinations Commission Leaving Certificate Examination 2010 Technology Coursework Briefs Ordinary Level and Higher Level 200 marks The Thematic Briefs for the Leaving
More informationMathematics 43601F. Geometry. In the style of General Certificate of Secondary Education Foundation Tier. Past Paper Questions by Topic TOTAL
Centre Number Surname Candidate Number For Examiner s Use Other Names Candidate Signature Examiner s Initials In the style of General Certificate of Secondary Education Foundation Tier Pages 2 3 4 5 Mark
More information0810ge. Geometry Regents Exam y # (x $ 3) 2 % 4 y # 2x $ 5 1) (0,%4) 2) (%4,0) 3) (%4,%3) and (0,5) 4) (%3,%4) and (5,0)
0810ge 1 In the diagram below, ABC! XYZ. 3 In the diagram below, the vertices of DEF are the midpoints of the sides of equilateral triangle ABC, and the perimeter of ABC is 36 cm. Which two statements
More informationIntermediate Tier Friday 10 November 2006 Morning Time: 2 hours
Centre No. Candidate No. Paper Reference 5 5 2 3 0 4 Paper Reference(s) 5523/04 Edecel GCSE Mathematics A 1387 Paper 4 (Calculator) Intermediate Tier Friday 10 November 2006 Morning Time: 2 hours Surname
More informationMethods in Mathematics (Linked Pair Pilot)
Centre Number Surname Candidate Number For Examiner s Use Other Names Candidate Signature Examiner s Initials Methods in Mathematics (Linked Pair Pilot) Unit 2 Geometry and Algebra Monday 11 November 2013
More informationMODELING AND DESIGN C H A P T E R F O U R
MODELING AND DESIGN C H A P T E R F O U R OBJECTIVES 1. Identify and specify basic geometric elements and primitive shapes. 2. Select a 2D profile that best describes the shape of an object. 3. Identify
More information2 a Shade one more square to make a pattern with just one line of symmetry.
GM2 End-of-unit Test Rotate the shape 80 about point P. P 2 a Shade one more square to make a pattern with just one line of symmetry. b Shade one more square to make a pattern with rotational symmetry
More informationLeaving Certificate Applied 2016
2016 AP9.11 Coimisiún na Scrúduithe Stáit State Examinations Commission Leaving Certificate Applied 2016 Vocational Specialism Craft and Design Course Written Examination (40% of total marks) Date: Thursday
More informationLearning Outcomes. Students should be able to: Demonstrate an understanding of the planes of reference
Orthographic projection is a means of representing a three-dimensional (3D) object in two dimensions (2D). It is the projection by parallel rays onto a plane at right angles to the rays. Demonstrate an
More informationIsometric Drawing Chapter 26
Isometric Drawing Chapter 26 Sacramento City College EDT 310 EDT 310 - Chapter 26 - Isometric Drawing 1 Drawing Types Pictorial Drawing types: Perspective Orthographic Isometric Oblique Pictorial - like
More informationUNIVERSITY OF MALTA SECONDARY EDUCATION CERTIFICATE SEC GRAPHICAL COMMUNICATION. May 2017 EXAMINERS' REPORT MATRICULATION AND SECONDARY EDUCATION
UNIVERSITY OF MALTA SECONDARY EDUCATION CERTIFICATE SEC GRAPHICAL COMMUNICATION May 2017 EXAMINERS' REPORT MATRICULATION AND SECONDARY EDUCATION CERTIFICATE EXAMINATIONS BOARD SEC Graphical Communication
More informationTECHNICAL GRAPHICS AND DESIGN SYLLABUS
ZIMBABWE MINISTRY OF PRIMARY AND SECONDARY EDUCATION TECHNICAL GRAPHICS AND DESIGN SYLLABUS FORMS 1-4 2015-2022 Curriculum Development and Technical Services P.O. Box MP 133 Mount Pleasant Harare All Rights
More informationAuxiliary Elevations and Plans
Chapter 18 uxiliary Elevations and Plans uxiliary Elevations The pictorial view of the thatched cottage shown below indicates how the front elevation is: (i) Obtained from a viewing direction looking in
More informationCoimisiún na Scrúduithe Stáit State Examinations Commission. Leaving Certificate Examination Mathematics. Foundation Level
2017. M25 Coimisiún na Scrúduithe Stáit State Examinations Commission Leaving Certificate Examination 2017 Mathematics Friday 9 June Afternoon 2:00 4:30 300 marks Examination number Centre stamp For examiner
More informationGeometry Mrs. Crocker Spring 2014 Final Exam Review
Name: Mod: Geometry Mrs. Crocker Spring 2014 Final Exam Review Use this exam review to complete your flip book and to study for your upcoming exam. You must bring with you to the exam: 1. Pencil, eraser,
More informationMathematics (Project Maths Phase 2)
2013. M229 S Coimisiún na Scrúduithe Stáit State Examinations Commission Leaving Certificate Examination 2013 Sample Paper Mathematics (Project Maths Phase 2) Paper 1 Higher Level Time: 2 hours, 30 minutes
More information449/1 DRAWING AND DESIGN PAPER 1 MARKING SCHEME
MACHAKOS COUNTY KCSE TRIAL AND PRACTICE EXAM 2015 Kenya Certificate of Secondary Education 449/1 DRAWING AND DESIGN PAPER 1 MARKING SCHEME SECTION A 1. a) Information regarding parastatal organizations
More informationTECHNICAL DRAWING. SECTION A: will consist of (30) questions drawn from the general principles, techniques and uses of plane and solid geometry.
TECHNICAL DRAWING EXAMINATION SCHEME There will be three papers, Papers1, 2 and 3 all of which must be taken. Papers 1 and 2 will be a composite paper to be taken at one sitting. PAPER 1: will consist
More information