Lamp Replacement Instructions
|
|
- Jonas Cobb
- 6 years ago
- Views:
Transcription
1 Introduction Lamp Replacement Instructions Use the following instructions when replacing the lamp on the projector model listed in Table 1, below. The lamp is located at the front of the projector and can be accessed by removing the front cover. Use only a Christie approved Lamp Kit for the specific projector model. Table 1. Projector Models Projector Model Model Number Required Lamp Kit Christie DS Warnings Lamp replacement MUST be performed by a qualified service technician. Cool the lamp completely (approximately 60 minutes) and handle by the housing only. Install the correct wattage lamp, supplied by Christie (Refer to Table 1. Projector Models) and read the Lamp Replacement Procedure in its entirety before proceeding. Do not touch the glass surface of the lamp. Fingerprints left on the surface can lead to an intense accumulation of heat known as a hotspot, which could potentially cause the lamp to shatter. It is recommended to wear clean, lint-free gloves and a face shield when working with the lamp. In the unlikely event that the bulb ruptures, small glass fragments may come loose. The lamp module is designed to contain the glass fragments; however, it is advised that extreme caution is exercised when removing the lamp module (Rev. 1) 1 of 5 Pages
2 Lamp Replacement Procedure Please read before proceeding WARNING Always power down and unplug the projector prior to servicing. Allow the lamp to cool before handling. STEP 1 - TURN THE LAMP OFF Press (power) to turn the projector OFF. Allow the cooling fans to stop automatically (approximately five minutes) before proceeding with Step 2. STEP 2 - UNPLUG THE PROJECTOR When the cooling fans have stopped, turn the projector s main switch OFF and unplug from the main power source. Wait approximately 60 minutes to allow sufficient time for the lamp to cool down. Do not open the lamp cover until this time has elapsed. STEP 3 - REMOVE FRONT COVER Release the front cover screw and remove the front cover. Refer to Figure 1. Figure 1. Remove Front Cover (Rev. 1) 2 of 5 Pages
3 STEP 4 - REMOVE THE LAMP MODULE (a) Unscrew the three mounting screws securing the lamp module. Refer to Figure 2. (b) Release the handle. Refer to Figure 2. (c) Remove the lamp module from the projector housing. Refer to Figure 2. Figure 2. Remove Lamp Module STEP 5 INSERT NEW LAMP MODULE (a) Use the designated guide pins to insert the new lamp module. Refer to Figure 3. (b) Firmly screw-in the three mounting screws to secure the lamp module. Do not use excess force. Refer to Figure 3. (c) Secure the handle. Refer to Figure 3. Figure 3. Insert New Lamp Module (Rev. 1) 3 of 5 Pages
4 STEP 6 REPLACE FRONT COVER IMPORTANT The lamp module is calibrated for maximum performance and brightness in this projector. Do not attempt to re-align or adjust the lamp module. Replace the front cover and tighten the front cover screw to secure the cover to the projector housing. Do not use excess force. Refer to Figure 4. Figure 4. Replace Front Cover STEP 7 RESET THE LAMP HOURS Once the lamp is replaced it is important to reset the lamp properties. To do this access the User Menu, use the up/down scroll to highlight the LAMP RESET option and click on the arrow icon. Refer to Figure 5. Figure 5. User Menu (Rev. 1) 4 of 5 Pages
5 Technical Support 809 Wellington St. North Kitchener, Ontario, Canada N2G 4Y7 Tel (General) Toll Free (Technical Support) Fax (Service) View Point 200 Ashville Way Wokingham, Berkshire RG41 2PL United Kingdom Tel Fax , av Georges Pompidou Levallois-Perret Cedex France Tel. +33-(0) Fax +33-(0) A Aljunied Road # Biz Tech Centre Singapore Tel Fax NORTH AMERICA EUROPE ASIA-PACIFIC / OTHER Camden Drive Cypress, CA USA Tel (General) Toll Free (Technical Support) Fax (Service) Willicher Damm 129 D Mönchengladbach Germany Tel Fax Rm Shartex Plaza No. 88 Zun Yi South Road Shanghai, People s Republic of China Tel Fax CHRISTIE Sales (Canada) CHRISTIE Sales (U.S.) Tel Tel or Fax Fax (Rev. 1) 5 of 5 Pages
NOTE: Refer to the User s Manual ( xxP) for more information on Lamp Operation Modes.
Introduction Applies to RPMS-D100U/UF (38-GFX204-01, 38-GFX205-01, 38-GFX206-01, 38-GFX207-01), CS70-D100U/UF (38-GFX052-xx, 38-GFX053-xx) and CS50-D100U (38-GFX054-xx). RPMS-D100U/UF, CS50-D100U and CS70-D100U/UF
More informationCAUTION: To prevent damage to your equipment, thoroughly study all instructions and illustrations before you begin to install the extension.
I N S T R U C T I O N M A N U A L The Christie Vivid extension is an easy to install option designed to provide quick height adjustment for your installation needs. This extension can be secured to ceilings
More informationIMPORTANT WARNINGS AND CAUTIONS!
I N S T R U C T I O N M A N U A L The Christie Vivid Green ceiling mount will suspend your Christie Vivid Green projector in an upright position to compliment conference rooms, classrooms or home theater
More information2004-(Z Series) HDILA Lamp Replacement Procedure Quick Step Guide
2004-(Z Series) HDILA Lamp Replacement Procedure Quick Step Guide How To Determine If The Lamp Requires Replacement? After 30 seconds of turning on the TV The POWER LED and LAMP LED rapidly blink together
More informationRPMSP Series Installation Guide
RPMSP Series Installation Guide Contents 1. Overview... page 1 2. Unpacking the Projector...2 3. Projector Configuration...2 4. Projector Throw Distance and Mounting...9 5. Projection Lens Focus...9 6.
More informationName Class Date. Brightness of Light
Skills Practice Lab Brightness of Light IN-TEXT LAB CBL VERSION The brightness, or intensity, of a light source may be measured with a light meter. In this lab, you will use a light meter to measure the
More informationChristie Duo Stacking Frame
Christie Duo Stacking Frame Installation Manual 020-101055-01 Christie Duo Stacking Frame Installation Manual 020-101055-01 NOTICES COPYRIGHT AND TRADEMARKS 2013 Christie Digital Systems USA Inc. All
More informationThe Eyetracker. Bruno Bonet
The Eyetracker Bruno Bonet EYETRACKER The Eyetracker is at the end of the MRI room behind the machine. Do NOT move the Eyetracker EYETRACKER A bulb can light the pupil through mirrors and the reflected
More informationARROW SAW PRECISE CUT 8000 RPM WITH DUST COLLECTING ATTACHMENT INSTRUCTION BOOK MODEL NO
ATTENTION If any components of this unit are broken or the unit does not operate properly, please contact Cabela s Customer Service. Retail Store Purchases: 1-800-905-2731 (U.S. & Canada) Catalog and Internet
More informationRiverside. Windward Bay EntertaInment Wall System Assembly Instructions. Made In Viet Nam. Right Pier. Bridge & Back Panel.
EntertaInment Wall System Page 1 of 12 Product No. 42840 42848 42849 42843 Product Description Console Left Pier Right Pier Bridge & Back Panel Right Pier Bridge & Back Panel Left Pier 63" Inch Ent. Console
More informationCLEANING THE GALVO MIRRORS
CLEANING THE GALVO MIRRORS Formlabs Customer Support can provide additional information on mirror cleaning and in some cases, provide the customer with the appropriate cleaning supplies. Tools: 2.5mm hex
More informationAllegro Home Office Assembly Instructions. Tipping Restraint. Bun Foot W/ Leveler. 4 pcs.
email: info@riverside-furniture.com Allegro Home Office Assembly Instructions Components and Hardware List Page 1 of 5 Made in China Shelf Pin Wood Shelf File Rod & Clips 1/2"Wood Screw A 16 pcs. B 4 pcs.
More informationPERSONAL RECORD KEEPING
PRO3700 2 P R O 3 7 0 0 A s s e m b l y i n s t r u c t i o n s PERSONAL RECORD KEEPING Tip: Record the serial numbers of your Octane Fitness elliptical in the spaces below. This will make it easier for
More informationFABRICATOR 211i & 252i ROLL CAGE ASSEMBLY INSTRUCTIONS
Manual 0-5233 Manufacturer: Thermadyne Industries Address: 82 Benning Street West Lebanon, New Hampshire 03784 USA Telephone: 1-800-426-1888 Fax: 1-800-535-0557 Email: sales@thermalarc.com www.thermalarc.com
More informationASSEMBLY & DISASSEMBLY INSTRUCTIONS
ASSEMBLY & DISASSEMBLY INSTRUCTIONS http://www.sunnen.com for SUNNEN MPS-ANR TOOL/DRIVESHAFT CONNECTIONS I-ANR-260 GENERAL The following instructions cover the assembly and disassembly of Sunnen Wide Range
More informationInstalling the detector filter assembly (G )
s1 Installing the detector filter assembly (G1600-62700) The detector filter transmits light of a defined wavelength range. Figure 1 shows a typical transmission spectrum. Maximum transmission is between
More informationInstalling flat panels on the MPL15 wall mount
Installing flat panels on the MPL15 wall mount The MPL15 (DS-VW775) is a full-service video wall mount that can accommodate tiled LCD panels with up to a 400 x 400 mm VESA pattern in portrait and landscape
More informationCWS 500N1.4 CONTINUOUS WAVE SIMULATOR, 80W
CWS 500N1.4 CONTINUOUS WAVE SIMULATOR, 80W FOR TESTS ACCORDING TO... > EN 300329 > EN 300340 > EN 300342-1 > EN 300386 V1.3.2 > EN 301489-1 > EN 301489-17 > EN 301489-24 > EN 301489-7 > EN 55024 > EN 61000-4-6
More informationCTR2 / CTR2-AD CALIBRATION TARGET AND VERIFICATION ADAPTER FOR ESD
CTR2 / CTR2-AD CALIBRATION TARGET AND VERIFICATION ADAPTER FOR ESD FOR TESTS ACCORDING TO... > EN 61000-4-2 > IEC 61000-4-2 > ISO 10605 ESD CALIBRATION TARGET The CTR 2 is a coaxial current target to monitor
More informationWelding & Fabrication Tools R8 Mini Pliers
With Volta Tools You Can Never Go Wrong! Fast and simple belt installation. Unique and versatile design - compact, rugged and easy-to-use. Designed for both shop and field use. Light-weight construction.
More informationInstruction manual SUN-PM100L. SUN-PM100L Polishing Machine English
Instruction manual SUN-PM100L SUN-PM100L Polishing Machine English Table: SUN-UM-TL-PM001 Version: A/0 Fiber Optic Solutions Provider Ⅰ Safety Precautions To ensure safe operation and maximize product
More informationQuolis 5000 Light INSTALLATION AND OPERATION INSTRUCTIONS. Model AL-820 IMPORTANT
Quolis 5000 Light Model AL-80 INSTALLATION AND OPERATION INSTRUCTIONS IMPORTANT After installation is completed, check all the bolts, screws and fasteners to confirm that they are securely fastened. R
More informationTUNING A MODEL CTA MODULE
TUNING A MODEL 183150 CTA MODULE TECHNICAL NOTE HWA-002 TSI strives to ship Thermal Anemometry systems that are ready to use by our customers. There are occasions when the system should be shipped back
More informationChristie Mystique Install: Comparing features by edition
Christie Mystique Install: Comparing features by edition Essentials Edition Pro Venue Edition Premium Edition Large Scale Experience Edition for flat screens and surfaces for flat and cylindrical screens
More informationPage 1 T O O L S A N D M AT E R I A L S R E Q U I R E D. 1. Screwdriver 2. Carpenter's level 3. Electrical Tape PA R T S L I S T. A.
T O O L S A N D M AT E R I A L S R E Q U I R E D 1. Screwdriver 2. Carpenter's level 3. Electrical Tape PA R T S L I S T A. Cabinet B. Wood Screw X4 C. Plastic wire connector x3 Page 1 I M P O R TA N T
More informationimpact VC-500LR Monolight INSTRUCTIONS
impact lighting equipment and accessories VC-500LR Monolight INSTRUCTIONS Congratulations on your purchase of the Impact VC-500LR Monolight. We feel that it will contribute much to your photographic skill
More informationINSTRUCTION MANUAL. Force Transducer Output Tube Repair Kit
INSTRUCTION MANUAL Model 400-TR Force Transducer Output Tube Repair Kit June 4, 2004, Revision 5 Copyright 2004 Aurora Scientific Inc. Aurora Scientific Inc. 360 Industrial Pkwy. S., Unit 4 Aurora, Ontario,
More informationC6 Corvette Rear Spoiler Kit CDC #
2005 2008 C6 Corvette Rear Spoiler Kit CDC # 0542 7002 01 Note: Read installation instructions before starting Kit Includes: 1 C6 Rear Spoiler 2 CHMSL Bracket # 0542-3500-01 2 Screw 4.2 x 1.41 x 25 # 30005
More informationPORTABLE HALOGEN WORK LIGHT OWNER S MANUAL
PORTABLE HALOGEN WORK LIGHT OWNER S MANUAL L-9001 (29278) L-9002 (29276) WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules
More informationApplication Tooling Specification Sheet
Tool Kit Order No. 63811-5370 FEATURES Application Tooling Specification Sheet TYPE 4C Hand Crimp Tool Order No. 63811-5300 % A full cycle ratcheting hand tool ensures complete crimps % Ergonomically designed
More informationZ-Truck Up-and-Down Motion. Y-Truck Side-to-Side Motion. Head. Squaring Plate. Sliding Plate FIGURE 1: THE CARVEWRIGHT MACHINE
Setup and use of CarveWright CO2 Powered Dragster Jig The CO 2 powered Dragster Jig will arrive from the factory fully assembled, calibrated, and squared. In order to get the best results, your CarveWright
More information12912 Farnham Avenue White Bear Lake, Minnesota WILSON WHEEL OPERATOR S MANUAL. for Amada Thick Turret Punch Presses
12912 Farnham Avenue White Bear Lake, Minnesota 55110 WILSON WHEEL OPERATOR S MANUAL for Amada Thick Turret Punch Presses Rolling Shear Rolling Rib Rolling Offset Rolling Pincher Revised: September 20,
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Tow Hitch Finisher Pathfinder (2013) 999T5 RZ030 Installation of this accessory requires installation of additional
More informationPORTA~TRACE. GAGNE, INC. 41 Commercial Dr. Johnson City, New York Phone: Fax: ASSEMBLY INSTRUCTIONS
PORTA~TRACE GAGNE, INC. 41 Commercial Dr. Johnson City, New York 13790 Phone: 1-607-729-3366 Fax: 1-607-729-7644 ASSEMBLY INSTRUCTIONS PORTA~TRACE MODEL 2436T LIGHT TABLE PORTA~TRACE MODEL 3648T LIGHT
More informationINSTRUCTIONS PS2500 POWER SUPPLY
INSTRUCTIONS PS2500 POWER SUPPLY The Hoefer PS 2500 Power Supply will furnished power to Constant Voltage or Constant Power modes of operation. It will accurately supply 0-2500 volts, 0-300 ma or 0-375
More informationMTRTH and MTRTLS. MRT and MRS METAL CABLE TIE RETAINED TENSION INSTALLATION TOOLS OPERATION INSTRUCTIONS
MTRTH and MTRTLS PA25279A01 Rev. 02 4-2009 MRT and MRS METAL CABLE TIE RETAINED TENSION INSTALLATION TOOLS OPERATION INSTRUCTIONS Panduit Corp. 2009 INTRODUCTION The MTRTH Retained Tension Installation
More informationSmartBlock I/O Module - HE579DAC107/HE579DAC207 8/4 Channel Current and Voltage Output 0-5V / 0-10V / 4-20mA / 0-20mA - CsCAN
SmartBlock I/O Module - HE579DAC107/HE579DAC207 8/4 Channel Current and Voltage Output 0-5V / 0-10V / 4-20mA / 0-20mA - CsCAN 1. SPECIFICATIONS / DIMENSIONS ANALOG OUT Number of Outputs 8 (207) or 4 (107)
More informationReplacement Guide For Ventilating Window on Self-Storing Door with Retractable Insect Screen
Replacement Guide For Ventilating Window on Self-Storing Door with Retractable Insect Screen IMPORTANT: READ ENTIRE GUIDE BEFORE BEGINNING INSTALLATION. PLEASE NOTE: Proper assembly, installation and maintenance
More informationGeneral Installation Instructions LED
General Installation Instructions LED To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions and other hazards, please read all warnings
More informationSTYLE RA DIO France Inter - DCF
Style 7 STYLE RA DIO France Inter - DCF Style 7D Style 7E INSTALLATION AND OPERATING INSTRUCTIONS B.P. 1 49340 TRÉMENTINES FRANCE Tél. : 02 41 71 72 00 Fax : 02 41 71 72 01 www.bodet.com Réf.: 605723 G
More informationAngle Grinder. Model Visit our website at:
Angle Grinder Safety Guard Model 45921 Installation Instructions Note: Cutting Blade and Angle Grinder sold separately. Visit our website at: http://www.harborfreight.com Read this material before using
More informationSCXI High-Voltage Terminal Block
INSTALLATION GUIDE SCXI -326 High-Voltage Terminal Block Introduction This guide describes how to use and install the SCXI-326 high-voltage terminal block with the SCXI-62, the SCXI-63, the SCXI-62HV,
More information6 BLADE CUTTER MODEL # PCC-6 OPERATION MANUAL
4511 WAYNE AVENUE PHILADELPHIA PA 19144 TEL: 888-800-2663 FAX: 800-582-9643 6 BLADE CUTTER MODEL # PCC-6 OPERATION MANUAL CONTENTS I. INTRODUCTION TO BOND PCC-6 / MACHINE SPECIFICATIONS II. SAFETY PRECAUTIONS
More informationINSTALLATION MANUAL PBC-UMS
INSTALLATION MANUAL. PBC-UMS Premier Mounts 3130 E. Miraloma Avenue Anaheim, CA 92806 Phone: (800) 368-9700 Fax: (800) 832-4888 mounts@mounts.com www.mounts.com Rev. 01 PBL-110 Projector Mount Page 2 Installation
More informationTech. Services: (800) Fax: (800) Order Entry: (800) Fax: (800) NUT SPLITTER. Max.
SPX Corporation 5885 11th Street Rockford, IL 61109-3699 USA Internet Address: http://www.powerteam.com Tech. Services: (800) 477-8326 Fax: (800) 765-8326 Order Entry: (800) 541-1418 Fax: (800) 288-7031
More informationRepair Instructions ISC. Experience In Motion. ISC1PX Single Pusher Seal
Repair Instructions ISC ISC1PX Single Pusher Seal Experience In Motion These instructions are written for trained, experienced technicians familiar with the basic principles and tools involved in the installation,
More informationClear jammed paper from the input tray Remove any jammed paper that is accessible from the input tray area.
Step 1: Clear jammed paper from the printer Paper jams can occur in multiple areas of the printer. If you cannot find the paper jam in one area, continue to the next area until the jam is located. note:
More informationINSTALLATION HANDBOOK
Replacing Consumables Replacing the Lamps Lamp replacement period It is time to replace the lamp when: The message "Replace the lamp." is displayed at the lower left of the projection screen when you start
More informationMaintenance and other important non-personal injury and non-material damage instructions or statements that should be observed.
VIGO INDUSTRIES INSTALLATION GUIDE FOR SHOWER ENCLOSURE ()! SAFETY PRECAUTIONS This Installation Guide uses the following symbols to indicate important information. Always observe the instructions indicated
More informationBO-01 Blackout. Operation & Service Manual. Version 1.1. * Read this manual before use
BO-01 Blackout Operation & Service Manual Version 1.1 * Read this manual before use General Remark If you encounter any difficulties or if you need support on how to update and/ or install your Blackout
More informationWelding & Fabrication Tools FT-Flat Electrode Welding
Welding & Fabrication Tools FT-Flat Electrode Welding Instruction Manual The Next Step in Belting Welding & Fabrication FT-Flat Electrode Welding Table of Contents Page How to Use this Manual 3 Symbols
More informationWELDING EQUIPMENT TROLLEY ASSEMBLY INSTRUCTIONS
Manual 0-5211 Cigweld Pty Ltd 71 Gower Street Preston, Victoria, Australia, 3072 Telephone: +61 3 9474 7400 FAX: +61 3 9474 7488 Email: cigweldsales@cigweld.com.au Website: www.cigweld.com.au! Maximum
More informationPARTS ENCLOSED: (A) Wall anchor (1) (B) Wall screw (1) (C) 4W Type G Bulb (1) (included)
making it easy to create an elegant nursery or child's bedroom. Each item s surface is sealed, which (A) Wall anchor (1) (B) Wall screw (1) (C) 4W Type G Bulb (1) (included) MARQUEE SYMBOL DOT For safety
More informationB235 Mobius Sconce Page 1 of 6
Mobius Sconce 28-9450 Page 1 of 6 CAUTION: FAILURE TO INSTALL THIS PRODUCT PROPERLY MAY RESULT IN PERSONAL INJURY OR PROPERTY DAMAGE. We recommend installation by a qualified individual trained in the
More informationDisclaimers. Important Notice
Disclaimers Disclaimers Important Notice Copyright SolarEdge Inc. All rights reserved. No part of this document may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means,
More informationTurn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
Quoizel, Inc. 6 Corporate Parkway Goose Creek, SC Customer Service Phone 63.273.2700 Fax 63.23.702 www.quoizel. ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wire strippers,electricaltape,safetyglasses.
More informationReaction Chromatic Tuner Instruction Manual
Reaction Chromatic Tuner Instruction Manual Compliance Your Reaction Chromatic Tuner pedal has been tested and complies with the following Standards and Directives as set forth by the European Union: Council
More informationBuilding the First Row Table Assembly
CHAPTER 6 Revised: December 2, 2011, Note You install all first row table sections in this chapter except the table door. You must install the presentation display and speaker screens before installing
More informationINSTALLATION MANUAL ELPMB50
INSTALLATION MANUAL ELPMB50 Frame for Epson projectors Epson EB-L1100 Epson EB-L1200 Epson EB-L1300 Epson EB-L1405 Epson EB-L1500 Epson EB-L1505 Safety instructions 1 Product description 5 Installing the
More informationEllisSaw.com. EllisSaw.com P.O. Box Verona, WI
P.O. Box 9019 Verona, WI 9-019 GENERAL OPERATING & SAFETY INSTRUCTIONS * READ INSTRUCTIONS BEFORE USE * CAUTION: Disconnect power supply cord from power source when doing repair work or changing belt.
More informationSignet 2610 Process Optical Dissolved Oxygen Sensor
Signet 2610 Process Optical Dissolved Oxygen Sensor *3-2610.090* 3-2610.090 Rev. A 04/12 English Operator's Manual Introduction System Description Your new RDO Pro is a rugged, reliable sensor designed
More informationSterling. Power Amplifiers User Manual. Models Covered
Sterling Power Amplifiers User Manual Models Covered Stereo 12 Watt Mk 1 & 2 Stereo Plus 18 Watt Mk 1 & 2 Stereo Integrated 12 & 18 Watt Mk 1 & 2 Stereo Integrated Remote 12 & 18 Watt Mk 1 & 2 Parallel
More informationModel #2 UVB Midband Ultraviolet Lamp Assembly with Timer
UVB Midband Technology The Model 2 Rayminder Lamp - The World's Only UVB Midband Lamp Based On Original Research Patented design based on research. Tested and certified to Rayminder's Proprietary Select
More informationCaution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
izz Kitchen Pendant With Brass Accent - 18700 Page 1 of 5 CAUTON: AUR TO NSTA THS XTUR PROPRY MAY RSUT N SROUS PRSONA NURY OR DATH AND PROPRTY DAMAG. We recommend installation by a licensed electrician.
More informationSPOT WELD CUTTER SHARPENER
670 New York Street Tel: 800.261.7976 Memphis, TN 38104 Fax: 901.274.8816 www.chemicar.com sales@chemicar.com SPOT WELD CUTTER SHARPENER OPERATING MANUAL CONTENTS WARNINGS 2 OPERATING INSTRUCTIONS 3 REPLACING
More information4" (DN 100) 5RET Tank Car Fire-Tite Bottom Unloading Valves. Installation, Maintenance and Operating Instructions
4" (DN 100) 5RET Tank Car Fire-Tite Bottom Unloading Valves Installation, Maintenance and Operating Instructions IMO-R14 11/2013 2 IMO-R14 Table of Contents 1 GENERAL....................................
More informationPlease read these instructions before use and keep for future reference
Wardrobe Assembly Guide Allen Key Provided (if required) Philips Screwdriver Required Hammer Required Please read these instructions before use and keep for future reference Caution! Two Person Assembly
More informationApplication Tooling Specification Sheet
Tool Kit Order No. 63823-6470 FEATURES Application Tooling Specification Sheet Hand Crimp Tool Order No. 63823-6400 % A full cycle ratcheting hand tool ensures complete crimps % Ergonomically designed
More informationSmart Lock. Showcase Lock + Door Brace (For Double Swing-Out Doors) PL401 + PL420-01
Smart Lock Showcase Lock + Door Brace (For Double Swing-Out Doors) PL401 + PL420-01 1 Overview Review entire instruction guide before starting installation. Instructions are intended for double swing-out
More informationPro-Doweling Kit USER S MANUAL #840. Visit us at
Pro-Doweling Kit USER S MANUAL #840 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Please read this manual carefully and thoroughly
More informationInstallation Instructions
CRLVHLGD017A00 CRLVHLGD026A00 - ACCESSORY LOUVERED HAIL GUARD GAS HEAT/ELECTRIC COOLING, ELECTRIC COOLING AND HEAT PUMP ROOFTOP UNITS 15 to 28 TONS Installation Instructions IMPORTANT: Read these instructions
More informationRosemount 5408 and 5408:SIS Level Transmitters
Quick Start Guide 00825-0100-4408, Rev AD March 2018 Rosemount 5408 and 5408:SIS Level Transmitters Cone Antenna Quick Start Guide March 2018 1 About this guide This Quick Start Guide provides basic guidelines
More informationINSTRUCTION MANUAL TWIN WOODEN DAYBED MODEL NO: UPC CODE: NOTE: Lot number: Date of purchase: / / WM6394E ESPRESSO WM6394W WHITE WM6394B BLACK
INSTRUCTION MANUAL TWIN WOODEN DAYBED MODEL NO: WM6394E ESPRESSO WM6394W WHITE WM6394B BLACK UPC CODE: 0-65857-16370-4 ESPRESSO 0-65857-16371-1 WHITE 0-65857-16890-7 BLACK NOTE: THIS INSTRUCTION BOOKLET
More informationApplication Tooling Specification Sheet
Tool Kit Order No. 63811-7370 FEATURES Application Tooling Specification Sheet TYPE 4C Hand Crimp Tool Order No. 63811-7300 % A full cycle ratcheting hand tool ensures complete crimps % Ergonomically designed
More informationOwner s Manual. Model Number: B4772
TM Owner s Manual Model Number: B4772 2 Let s Go! Before inserting a software cartridge, turn power off! Insert the software cartridge into the software port. Turn power back on. Software Cartridge Software
More informationInstallation Instructions
MUSTANG RTR SIDE ROCKER SPLITTER KIT Part # 1011-7000-01 Application: 2010-2014 Mustang Installation Instructions Before installing your RTR components, rear through the entire installation process and
More informationEdition Notes Edition Notes Trademarks Copyright Notice Copyright 2012 CHAUVET Manual Usage Document Printing Intended Audience Disclaimer CHAUVET
User Manual Edition Notes Edition Notes Trademarks Copyright Notice Manual Usage Document Printing Intended Audience Disclaimer CHAUVET Publications Hot Line Document Revision Fixture at a Glance CHAUVET
More informationGlass cleaning hp scanjet 4500c/5550c scanner
Glass cleaning hp scanjet 4500c/5550c scanner Before proceeding, read these instructions all the way through. Then return here and follow the steps in order. This module is organized into the following
More informationTech Support Instructions for moving power on device
Tech Support Instructions for moving power on device Dear Pre-K SPED Teachers: Please read email below sent from Dearta regarding upgrades to the Teach Smart System: I wanted to give you some information
More informationSCXI High-Voltage Terminal Block
INSTALLATION GUIDE SCXI -1324 High-Voltage Terminal Block This guide describes how to install and use the SCXI-1324 high-voltage terminal block with the SCXI-1160 module. The SCXI-1324 high-voltage terminal
More informationOwner s Manual Model Number: H0404
Owner s Manual Model Number: H0404 2 Let s Go! Before inserting a software cartridge, turn power off! Insert the software cartridge into the software port. Turn power back on. Software Cartridge Software
More informationDisclaimers. Important Notice
Disclaimers Disclaimers Important Notice Copyright SolarEdge Inc. All rights reserved. No part of this document may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means,
More informationTidland Slitter Shafts
TIDLAND SLITTING SOLUTIONS Tidland Slitter Shafts Installation, Operation and Maintenance EN MI 666265 1 D Knife Shaft (tubular) KT Knife Shaft (solid) KS Anvil Roll (KS with sleeves) AR IMPORTANT SAFETY
More informationWall Mount Kit for Elo IDS-02 Series IDS Displays
Quick Installation Guide Wall Mount Kit for Elo IDS-02 Series IDS Displays Revision B P/N UM600076 Safety Warning: Do not install this equipment on any wall or structure that is not capable of supporting
More informationSFP-550. Operating Manual MATSUHIDAI, MATSUDO-CITY, CHIBA JAPAN TEL: FAX:
SFP-550 Operating Manual 296-1 MATSUHIDAI, MATSUDO-CITY, CHIBA 270-2214 JAPAN TEL: +81-47-388-6111 FAX: +81-47-388-4477 Safety Precautions To ensure safe operation and maximize product service life, observe
More informationInstallation Instructions
SYSTXBBSAM01 EVOLUTION SYSTEM ACCESS MODULE Installation Instructions NOTE: Read the entire instruction manual before starting the installation. pointsett U.S. Pat No. 7,415,102 Fig. 1 - Evolution System
More informationCWS 500N4 SIMULATOR FOR CONDUCTED, COMMON-MODE DISTURBANCES, AS PER IEC , IEC ANNEX C, 0HZ (DC) TO 165KHZ
CWS 500N4 SIMULATOR FOR CONDUCTED, COMMON-MODE DISTURBANCES, AS PER IEC 61000-4-16, IEC 61000-4-19 ANNEX C, 0HZ (DC) TO 165KHZ FOR TESTS ACCORDING TO... > EN 61000-4-16 > IEC 60255-22-7 > IEC 60255-26
More informationMercury 1200 and 1500P
Mercury 200 and 500P M200-Analog Output Encoder Systems M500P-Digital Output Encoder Systems Installation Manual and Reference Guide Manual No. IM-M200 & M500P Rev i Introduction MicroE Systems was founded
More informationSMALL GAUGE NIBBLER ASSEMBLY & OPERATING INSTRUCTIONS Mission Oaks Blvd., Camarillo, CA Visit our Web Site at
SMALL GAUGE NIBBLER 91739 ASSEMBLY & OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web Site at www.harborfreight.com Copyright 2004 by Harbor Freight Tools. All rights reserved.
More informationSCXI CURRENT INPUT,HIGH-VOLTAGE TERMINAL BLOCK
INSTALLATION GUIDE SCXI -1338 CURRENT INPUT,HIGH-VOLTAGE TERMINAL BLOCK Introduction This guide describes how to install and use the SCXI-1338 terminal block with your SCXI-1120, SCXI-1120D, SCXI-1125,
More information12 TON HYDRAULIC SHOP PRESS. Instruction Manual. Please read this instruction manual carefully before use.
12 TON HYDRAULIC SHOP PRESS Instruction Manual Please read this instruction manual carefully before use. IMPORTANT PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFETY INSTRUCTIONS AND WARNINGS. USE
More informationINSTALLATION MANUAL PBL-UMP
INSTALLATION MANUAL PBL-UMP Table of Contents Warning Statements... 4 Parts List... 5 Installation Tools... 5 Features... 7 Projector Preparation... 8 Bracket Installation... 10 Leveling the Mounting Bracket...
More informationHow to Assemble Your Solar Light & Accessories
1 How to Assemble Your Solar Light & Accessories geolitesolar.com customerservice@geolitesolar.com 2 Table of Contents 1. Put on Cotton Gloves...3 2. Assemble Base...3 3. Secure Base to Ground...4 4. Attach
More informationEMB Manufacturing Inc Boomer Line St. Clements, On N0B 2M0 Canada Ph: (519) Fax: (519) P200
BY EMB MFG INC. EMB Manufacturing Inc. 4144 Boomer Line St. Clements, On N0B 2M0 Canada Ph: (519) 699-9283 Fax: (519) 699-4146 www.embmfg.com P200 Pivoting Chainsaw Holder Accessory Installation Instructions
More informationBand-Master ATS Nano Pneumatic Banding Tool Operating Instructions
Band-Master ATS 601-118 Nano Pneumatic Banding Tool CONTENTS 601-118 Overview... 3 Safety.... 5 Initial Tool Set-up... 5 Regulator assembly mounting... 5 Attach tool head to regulator.... 6 Operating instructions...
More informationQUANTUM Qflash T2 / X2 OPERATING INSTRUCTIONS
QUANTUM Qflash T2 / X2 OPERATING INSTRUCTIONS 1.0 DESIGNATIONS T2 AND X2 1. Removable Reflector, two positions Normal and Wide angle. 2. Flash-tube 2A. Modeling Lamp (for Model X2 only) 3. Bounce Head,
More informationProjector Flush Mount
Projector Flush Mount ABtUS SIGAPORE PTE LTD Model: AV819 www.abtussingapore.com Patent Pending Revision 21/05/2012 ABtUS SINGAPORE PTE LTD www.abtussingapore.com User Operation Guide IMPORTANT NOTES Thank
More informationPMT-L31 (for Low Ceilings) PMT-H35 (for High Ceilings)
English Ceiling Mount Bracket PMT-L31 (for Low Ceilings) PMT-H35 (for High Ceilings) Installation Manual Be sure to read this manual thoroughly before using this bracket. After you have read this manual,
More informationFD35EV SLIDING DOOR SYSTEM Installation Manual (One-Way Soft Close, Recessed Mount Roller) Part No.FD35EVHCP
FD35EV SLIDING DOOR SYSTEM Installation Manual (One-Way Soft Close, Recessed Mount Roller) Part No.FD35EVHCP Thank you for selecting our product. Before starting installation, please read this manual thoroughly
More informationVDS 200Q SERIES 4-QUADRANT VOLTAGE DROP SIMULATOR - BATTERY SIMULATOR AND DC VOLTAGE SOURCE
VDS 200Q SERIES 4-QUADRANT VOLTAGE DROP SIMULATOR - BATTERY SIMULATOR AND DC VOLTAGE SOURCE FOR TESTS ACCORDING TO... > ISO 16750-2 > OEM LV 124 > LV 148 > Audi (Reference vehicles) > BMW - (Airbag ECU)
More information