Marine operations and marine warranty
|
|
- Adam Lucas
- 5 years ago
- Views:
Transcription
1 STANDARD DNVGL-ST-N001 Edition June 2016 Amended November 2016 Full version For full version, enter My DNV GL ( click "Add services" and find "DNV GL Noble Denton marine services warranty standards wizard" in the service catalogue. Tutorial ( The electronic pdf version of this document, available free of charge from is the officially binding version.
2 FOREWORD DNV GL standards contain requirements, principles and acceptance criteria for objects, personnel, organisations and/or operations. June 2016 Any comments may be sent by to This service document has been prepared based on available knowledge, technology and/or information at the time of issuance of this document. The use of this document by others than DNV GL is at the user's sole risk. DNV GL does not accept any liability or responsibility for loss or damages resulting from any use of this document.
3 CHANGES CURRENT This was a new edition in June 2016 and has been amended latest in November Changes in this document are highlighted in red colour. However, if the changes involve a whole chapter, section or sub-section, normally only the title will be in red colour. Amendments November 2016 References to the full version and the tutorial have been added on the front page in order to further aid access to the wizard. Amendments August 2016 [1.3]: Reference to a tutorial has been added, giving detailed guidance on how to use the wizard. Changes - current Editorial corrections In addition to the above stated changes, editorial corrections may have been made. Standard DNVGL-ST-N001. Edition June 2016, amended November 2016 Page 3
4 CONTENTS Changes current... 3 Section 1 Introduction Changes Background Access to the standard Use of the standard... 5 Contents Changes historic...6 Standard DNVGL-ST-N001. Edition June 2016, amended November 2016 Page 4
5 SECTION 1 INTRODUCTION 1.1 Changes This document (DNVGL-ST-N001 - Edition June 2016) replaces the legacy DNV-OS-H101, DNV-OS-H102, DNV-OS-H201, DNV-OS-H202, DNV-OS-H204, DNV-OS-H205 and all legacy GL Noble Denton Guidelines except 0009/ND and DNV-OS-H203, which are addressed in the DNVGL-ST-N002 standard (planned published 2016), and 0021/ND which will be addressed in the service specification DNVGL-SE-0122 (planned published 2016). 1.2 Background DNV GL Noble Denton marine services is a global provider of marine warranty services and has set the industry standard for marine operations and marine assurance activities for the last 50 years. Our collective industry best practice and guidance documentation is referenced and used all over the world. This document includes the harmonized legacy DNV standards and legacy GL Noble Denton guidelines, with the exception of those for MODU/MOU site specific assessment. Where DNV GL Noble Denton marine services is the marine warranty survey (MWS) provider, it should be read in conjunction with DNVGL-SE-0080 Noble Denton marine services - marine warranty survey, which provides a description of the process used by DNV GL Noble Denton marine services when providing MWS services to evaluate whether a marine operation can be accepted for the purposes of insurance-related MWS. It addresses both 'project' and MODU/MOU related MWS. This document may be used in its complete form using the relevant sections based on the asset type and/or operation. 1.3 Access to the standard The reader can access the standard through the Noble Denton marine services wizard available in My DNV GL ( Please see this tutorial for further detailed guidance ( oilgas/articles/noble-denton-marine-warranty-standards-wizard-tutorial.html). 1.4 Use of the standard The use of this standard presupposes and does not replace the application of industry knowledge, experience and know-how throughout the marine operation activities. It should solely be used by competent and experienced organizations, and does not release the organizations involved from exercising sound professional judgment. DNV GL has however no obligations or responsibility for any services related to this standard delivered by others. DNV GL has a qualification scheme mandatory to approval engineers and surveyors providing services related to this standard. This ensures that all approvals and certificates delivered are carried out by well qualified personnel who understand the intention behind the standard, the limitations and the correct interpretations. The use of this document is at the user's sole risk. DNV GL does not accept any liability or responsibility for loss or damages resulting from any use of this document. Standard DNVGL-ST-N001. Edition June 2016, amended November 2016 Page 5
6 CHANGES HISTORIC There are currently no historical changes for this document. Changes historic Standard DNVGL-ST-N001. Edition June 2016, amended November 2016 Page 6
7 DNV GL Driven by our purpose of safeguarding life, property and the environment, DNV GL enables organizations to advance the safety and sustainability of their business. We provide classification and technical assurance along with software and independent expert advisory services to the maritime, oil and gas, and energy industries. We also provide certification services to customers across a wide range of industries. Operating in more than 100 countries, our professionals are dedicated to helping our customers make the world safer, smarter and greener. SAFER, SMARTER, GREENER
DNV GL approval of service supplier scheme
CLASS PROGRAMME DNVGL-CP-0484 Edition February 2016 The electronic pdf version of this document, available free of charge from http://www.dnvgl.com, is the officially binding version. FOREWORD DNV GL class
More informationCouplings used for torque transmission in propulsion or auxiliary plants
CLASS PROGRAMME Type approval DNVGL-CP-0148 Edition March 2016 Couplings used for torque transmission in propulsion or auxiliary plants The electronic pdf version of this document, available free of charge
More informationDNVGL-CP-0212 Edition March 2016
CLASS PROGRAMME Type approval DNVGL-CP-0212 Edition March 2016 The electronic pdf version of this document, available free of charge from http://www.dnvgl.com, is the officially binding version. FOREWORD
More informationDNVGL-CP-0338 Edition October 2015
CLASS PROGRAMME DNVGL-CP-0338 Edition October 2015 The electronic pdf version of this document, available free of charge from http://www.dnvgl.com, is the officially binding version. FOREWORD DNV GL class
More informationDNVGL-CG-0214 Edition September 2016
CLASS GUIDELINE DNVGL-CG-0214 Edition September 2016 The content of this service document is the subject of intellectual property rights reserved by ("DNV GL"). The user accepts that it is prohibited by
More informationDNVGL-CP-0293 Edition July 2018
CLASS PROGRAMME Type approval DNVGL-CP-0293 Edition July 2018 The content of this service document is the subject of intellectual property rights reserved by ("DNV GL"). The user accepts that it is prohibited
More informationType Approval JANUARY The electronic pdf version of this document found through is the officially binding version
STANDARD FOR CERTIFICATION No. 1.2 Type Approval JANUARY 2013 The electronic pdf version of this document found through http://www.dnv.com is the officially binding version The content of this service
More informationDNVGL-CP-0400 Edition December 2015
CLASS PROGRAMME Type approval DNVGL-CP-0400 Edition December 2015 The electronic pdf version of this document, available free of charge from http://www.dnvgl.com, is the officially binding version. FOREWORD
More informationDNV GL Marine Renewables
ENERGY DNV GL Marine Renewables De-Risking Technologies, Insurance and Certification: The Certification Role Claudio Bittencourt Business Development Director Wave & Tidal Renewables Certification International
More informationPerformance-Based Safety Regulation
Performance-Based Safety Regulation Peter Bjerager, DNV GL National Academy of Sciences, 15 April 2016 1 SAFER, SMARTER, GREENER DNV GL in brief We classify, certify, verify and test against regulatory
More informationTaking a broader view
Taking a broader view A brief introduction to DNV GL 1 SAFER, SMARTER, GREENER We are a global classification, certification, technical assurance and advisory company 2 In a challenging world we make businesses
More informationConnecting Systems for Cable Repair (Cable Splices)
p pproval roramms for U rcos orasato Mutual coto (M)No. 2.9 STANDARD FOR CERTIFICATION Approval Programmes Type Approval Programmes for EU recognised organisation Mutual Recognition (MR) No. MR-E015 Connecting
More informationTechnology qualification management and verification
SERVICE SPECIFICATION DNVGL-SE-0160 Edition December 2015 Technology qualification management and verification The electronic pdf version of this document found through http://www.dnvgl.com is the officially
More informationDNV GL Strategic Research & Innovation
European Research Infrastructure supporting Smart Grid Systems Technology Development, Validation and Roll Out TRANSNATIONAL ACCESS PROVISION RESEARCH INFRASTRUCTURE DESCRIPTION AND TRANSNATIONAL ACCESS
More informationThe Verification Path
ENERGY The Verification Path Offshore Wind 4: Floating Wind Turbines All Energy 2016 Alexandra de Marichalar 1 SAFER, SMARTER, GREENER The origins of third party services, Year one of 150 years It is likely
More informationGENERAL DESCRIPTION OF THE CMC SERVICES
STANDARD FOR CERTIFICATION No.1.1 GENERAL DESCRIPTION OF THE CMC SERVICES MAY 2007 FOREWORD (DNV) is an autonomous and independent foundation with the objectives of safeguarding life, property and the
More informationUsing Norwegian competence from oil and gas subsea operations towards the development of ocean mining operations
Using Norwegian competence from oil and gas subsea operations towards the development of ocean mining operations Yoshinori Miura, Jens Laugesen, Øyvind Fjukmoen, Lucy Brooks, Karsten Hagenah, Tor Jensen
More informationAleks Karlsen/Jan van Tiggelen 20 September 2017
Presentation from Oslo Workshop Aleks Karlsen/Jan van Tiggelen 20 September 2017 1 SAFER, SMARTER, GREENER Content 1. DNV GL Project goal 2. Expected benefits of the new scheme 3. Project set-up 4. Current
More informationSummary of Changes and Current Document Status
DNV SERVICE DOCUMENTS Summary of Changes and Current Document Status FEBRUARY 2012 FOREWORD DET NORSKE VERITAS (DNV) is an autonomous and independent foundation with the objectives of safeguarding life,
More informationTECHNOLOGY QUALIFICATION MANAGEMENT
OFFSHORE SERVICE SPECIFICATION DNV-OSS-401 TECHNOLOGY QUALIFICATION MANAGEMENT OCTOBER 2010 FOREWORD (DNV) is an autonomous and independent foundation with the objectives of safeguarding life, property
More informationRecommended Practice for Wet and Dry Thermal Insulation of Subsea Flowlines and Equipment API RECOMMENDED PRACTICE 17U FIRST EDITION, FEBRUARY 2015
Recommended Practice for Wet and Dry Thermal Insulation of Subsea Flowlines and Equipment API RECOMMENDED PRACTICE 17U FIRST EDITION, FEBRUARY 2015 Special Notes API publications necessarily address problems
More informationIAMWS. International Association of Marine Warranty Surveyors
Company LOGO IAMWS International Association of Marine Warranty Surveyors An International & Professional Association for Marine Warranty Surveyors Introductory Seminar Lloyd s Old Library 25 April 2013
More informationContinuous On-line Measurement of Water Content in Petroleum (Crude Oil and Condensate)
API Manual of Petroleum Measurement Standards TR 2570 EI Hydrocarbon Management HM 56 Continuous On-line Measurement of Water Content in Petroleum (Crude Oil and Condensate) First Edition, October 2010
More informationMARITIME DNV GL. The European world-leading Class. Georgios Kasimatis 30 June MGUDE656 DNV GL June SAFER, SMARTER, GREENER
MARITIME DNV GL The European world-leading Class Georgios Kasimatis 30 June 2016 1 DNV GL 2016 20160628-MGUDE656 30 June SAFER, SMARTER, GREENER Trusted global partner with home in Europe 100 countries
More informationPart 7: Thermography
INTERNATIONAL STANDARD ISO 18436-7 Second edition 2014-04-01 Condition monitoring and diagnostics of machines Requirements for qualification and assessment of personnel Part 7: Thermography Surveillance
More informationAustralian/New Zealand Standard
AS/NZS 4114.2 Australian/New Zealand Standard Spray painting booths, designated spray painting areas and paint mixing rooms Part 2: Installation and maintenance This Joint Australian/New Zealand Standard
More informationAbstract. Mission. Exceptions
Marine transportation manual - a year 2000 joint industry project J.M.R. Lloyd Noble Denton Europe Ltd, Noble House, 131 Aldersgate Street, London EC1A 4EB, UK Abstract Mission To develop and publish a
More informationTechnological and Logistical Challenges during Construction & Installation of Deepwater Mega Subsea Development in West Africa
Technological and Logistical Challenges during Construction & Installation of Deepwater Mega Subsea Development in West Africa 1 SAFER, SMARTER, GREENER Content Going Deeper Scale/Size of Deepwater Mega
More informationOffshore Wind Risks - Issues and Mitigations
DNV Offshore Wind Soren Karkov DNV an independent foundation Our Purpose To safeguard life, property and the environment Our Vision Global impact for a safe and sustainable future 2 More than 145 Years
More informationIntroduction to Subsea Production Systems. What is Subsea? 02 What is Subsea? DNV GL DNV GL 2013 August 2015
Introduction to Subsea Production Systems 02 What is Subsea? August 2015 DNV GL 2013 August 2015 SAFER, SMARTER, GREENER What is Subsea? 2 1 Goals Know the main building blocks forming a subsea production
More informationMARITIME ACADEMY TRAINING COURSES WORLDWIDE. Creating perspectives SAFER, SMARTER, GREENER
MARITIME ACADEMY TRAINING COURSES WORLDWIDE Creating perspectives SAFER, SMARTER, GREENER MARITIME ACADEMY CREATING PERSPECTIVES We strongly believe that investment in training allows companies to take
More informationRef: S935/gb. 13 th April 2012
The Institution of Engineering and Technology Michael Faraday House Six Hills Way, Stevenage Hertfordshire, SG1 2AY United Kingdom T +44 (0) 1438 313311 F +44 (0) 1438 765526 www.theiet.org Ref: S935/gb
More informationAsset Integrity Management for Purpose-Built FPSO s and Subsea System Facilities
An Intensive 5 Day Training Course Asset Integrity Management for Purpose-Built FPSO s and Subsea System Facilities 09-13 Jul 2017, Dubai 09-APR-17 This course is Designed, Developed, and will be Delivered
More informationAustralian Standard. Design review AS IEC IEC 61160, Ed.2 (2005) AS IEC
AS IEC 61160 2008 IEC 61160, Ed.2 (2005) AS IEC 61160 2008 Australian Standard Design review This Australian Standard was prepared by Committee QR-005, Dependability. It was approved on behalf of the Council
More informationTaking the Hop, Skip and Jump from Offshore Access New W2W Industry Guidance
Taking the Hop, Skip and Jump from Offshore Access New W2W Industry Guidance ALL-ENERGY GLASGOW (6-7 May 2015) Hamish Holt DNV GL Aberdeen Hamish.holt@dnvgl.com SAFER, SMARTER, GREENER Introduction The
More informationArchitectural Design Sketching and Drawing
Higher National Unit Specification General information for centres Unit title: Architectural Design Sketching and Drawing Unit code: DW3R 34 Unit purpose: This Unit is designed to enable the candidate
More informationMonopile Upending Tool (MP-UT)
Monopile Upending Tool (MP-UT) Remotely controlled, safe and efficient upending of large monopiles Application + + Construction of Offshore Wind Farms (OWFs) Monopile Foundations Installation Short Description
More informationmarine, construction, drilling, floating production, decommissioning and renewables industries.
Maritime Assurance & Consulting Ltd (MAC), a Bureau Veritas Group Company, is a UK-based company with a global reach, offering a comprehensive range of support services to the Dynamic Positioning Assurance
More informationIntroduction to Subsea Production Systems. What is Subsea? 02 What is Subsea? DNV GL DNV GL 2013 September 2014
Introduction to Subsea Production Systems 02 What is Subsea? September 2014 DNV GL 2013 September 2014 SAFER, SMARTER, GREENER What is Subsea? 3 1 What is Subsea? 4 Subsea example 5 2 Subsea example 6
More informationWe Believe. Our Commitment
We Believe Prudent management towards safety and efficiency should be emerged effortless by adopting smart practices and forward thinking. Just focus on the root, all else will follow. Team work is a key
More informationIBC Information and Communication Committee, Nils Andreas Masvie 27 January Paris Marriott Opera Hotel. Ungraded
Is standardization a cost cutting panacea in today s low oil price environment? Sharing lessons from recent mega-projects e.g. Nord Stream and South Stream IBC Information and Communication Committee,
More informationIntegrity Management of Offshore Assets
OIL & GAS Integrity Management of Offshore Assets Opening session Leif Collberg 05 May 2017 1 DNV GL 2015 05 May 2017 SAFER, SMARTER, GREENER How regulations can solve the challenge of being performance
More informationAS/NZS 1200:2000 AS/NZS
AS/NZS 1200:2015 Australian/New Zealand Standard Pressure equipment Superseding AS/NZS 1200:2000 AS/NZS 1200:2015 AS/NZS 1200:2015 This joint Australian/New Zealand standard was prepared by joint Technical
More informationmonopile gripper arms
monopile gripper arms (MGA) Fixing the position of the monopiles during lowering to the seabed for stability and safety Application + + Construction of Offshore Wind Farms (OWFs) Monopile Foundations Installation
More informationNZQA registered unit standard version 2 Page 1 of 5
Page 1 of 5 Title Use marine radar on a restricted limits vessel Level 3 Credits 10 Purpose People credited with this unit standard are able to: relate the operating principles and conditions of marine
More informationSUMMARY REPORT AND RECOMMENDATIONS ON THE PREVENTION OF MARINE OIL POLLUTION IN THE ARCTIC.
Arctic Council Open Access Repository Arctic Council http://www.arctic-council.org/ 1.8 Sweden Chairmanship I (May 2011 - May 2013) 4. SAO Meeting, March 2013, Stockholm, Sweden SUMMARY REPORT AND RECOMMENDATIONS
More informationDNVGL-SI-0167 Edition July 2015
STATUTORY INTERPRETATIONS DNVGL-SI-0167 Edition July 2015 Verification for compliance with United Kingdom shelf regulations The content of this service document is the subject of intellectual property
More informationAS/NZS IEC :2013
AS/NZS IEC 61000.4.6:2013 IEC 61000-4-6, Ed. 3.0 2008, IDT Australian/New Zealand Standard Electromagnetic compatibility (EMC) Part 4.6: Testing and measurement techniques Immunity to conducted disturbances,
More informationMARITIME INDUSTRY MARITIME SERVICE OVERVIEW SAFER, SMARTER, GREENER
MARITIME INDUSTRY MARITIME SERVICE OVERVIEW SAFER, SMARTER, GREENER 02 MARITIME service overview 04 The importance of in-depth knowledge 06 Classification 07 Verification 10 Operational performance 13
More informationAutonomous and remotely operated ships
MARITIME Autonomous and remotely operated ships Presented at DVIS Rasmus Stute 1 SAFER, SMARTER, GREENER Agenda 1. What is it? 2. How to ensure safe implementations? 3. Research projects 4. Is it legal?
More informationNovel design approaches
MARITIME Novel design approaches DNV GL s perspective into creating more competitive marine assets George Dimopoulos, Ph.D. 15 November 2016 1 15 November 2016 SAFER, SMARTER, GREENER Asset competitiveness
More informationThis is a preview - click here to buy the full publication
IEC/TR 80002-1 TECHNICAL REPORT Edition 1.0 2009-09 colour inside Medical device software Part 1: Guidance on the application of ISO 14971 to medical device software INTERNATIONAL ELECTROTECHNICAL COMMISSION
More informationTHE TECHNICAL ADVISOR TO THE SUBSEA INDUSTRY
THE TECHNICAL ADVISOR TO THE SUBSEA INDUSTRY 02 DNV GL ACHIEVING THE POTENTIAL OF THE SUBSEA SECTOR Subsea facilities are playing an increasingly important role in the creation of cost-eficient ield developments.
More informationThe 58th Annual Pipeline Industries Guild Dinner Tuesday 10th March 2015
The 58th Annual Pipeline Industries Guild Dinner Tuesday 10th March 2015 Annual Dinner Booking Form sponsored by An evening of awards, networking, entertainment and much, much more www.pipeguild.com The
More informationAS/NZS IEC :2013
AS/NZS IEC 61000.4.2:2013 IEC 61000-4-2, Ed.2.0 2008, IDT Australian/New Zealand Standard Electromagnetic compatibility (EMC) Part 4.2: Testing and measurement techniques Electrostatic discharge immunity
More information1 SERVICE DESCRIPTION
DNV GL management system ICP Product Certification ICP 4-6-3-5-CR Document number: ICP 4-6-3-5-CR Valid for: All in DNV GL Revision: 2 Date: 2017-05-05 Resp. unit/author: Torgny Segerstedt Reviewed by:
More informationAustralian Standard. Electricity metering equipment (AC) Particular requirements
AS 62053.21 2005 AS 62053.21 2005 Australian Standard Electricity metering equipment (AC) Particular requirements Part 21: Static meters for active energy (classes 1 and 2) (IEC 62053-21, Ed.1.0 (2003)
More informationDEPARTMENT OF NATIONAL DEFENCE PHOTOGRAPHY CONTEST 2011
DEPARTMENT OF NATIONAL DEFENCE PHOTOGRAPHY CONTEST 2011 WHAT S NEW THIS YEAR For each Special Effect category submission submit, as a text file on your CD/DVD, a brief descriptive outline of how the special
More informationThis document is a preview generated by EVS
TECHNICAL REPORT IEC/TR 80002-1 Edition 1.0 2009-09 colour inside Medical device software Part 1: Guidance on the application of ISO 14971 to medical device software IEC/TR 80002-1:2009(E) THIS PUBLICATION
More informationDNVGL-SE-0478 Edition July 2017
SERVICE SPECIFICATION DNVGL-SE-0478 Edition July 2017 The electronic pdf version of this document, available free of charge from http://www.dnvgl.com, is the officially binding version. FOREWORD DNV GL
More informationAWS C3.9M/C3.9:2009 An American National Standard. Specification for Resistance Brazing
An American National Standard Specification for Resistance Brazing An American National Standard Approved by the American National Standards Institute July 30, 2008 Specification for Resistance Brazing
More informationApplication for Assessment of a full quality assurance system regarding Measuring Instruments in accordance with MID
Application for Assessment of a full quality assurance system regarding Measuring Instruments in accordance with MID Company (applicant): hereby applies to RISE Research Institutes of Sweden AB, as Notified
More informationStandard of Knowledge, Skill and Competence for Practice as an Architectural Technologist
Standard of Knowledge, Skill and Competence for Practice as an Architectural Technologist RIAI 2010 Contents Foreword 2 Background 3 Development of the Standard.4 Use of the Standard..5 Reading and interpreting
More informationJanuary 7, 1997 COATED PRINTING PAPER, GS-10 1 GS-10 SECOND EDITION JANUARY 7, This standard has been superseded by Edition 2.
January 7, 1997 COATED PRINTING PAPER, GS-10 1 GS-10 GREEN SEAL STANDARD FOR COATED PRINTING PAPER SECOND EDITION JANUARY 7, 1997 This standard has been superseded by Edition 2.1, July 12, 2013 Green Seal,
More information-SQA-SCOTTISH QUALIFICATIONS AUTHORITY HIGHER NATIONAL UNIT SPECIFICATION GENERAL INFORMATION AUGUST
-SQA-SCOTTISH QUALIFICATIONS AUTHORITY HIGHER NATIONAL UNIT SPECIFICATION GENERAL INFORMATION -Unit number- 4670968 -Unit title- -Superclass category- -Date of publication- (month and year) -Originating
More informationDNVGL-RP-A203 Edition June 2017
RECOMMENDED PRACTICE DNVGL-RP-A203 Edition June 2017 The electronic pdf version of this document, available free of charge from http://www.dnvgl.com, is the officially binding version. FOREWORD DNV GL
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 17894 First edition 2005-03-15 Ships and marine technology Computer applications General principles for the development and use of programmable electronic systems in marine applications
More information-SQA-SCOTTISH QUALIFICATIONS AUTHORITY NATIONAL CERTIFICATE MODULE: UNIT SPECIFICATION GENERAL INFORMATION. -Module Number Session
-SQA-SCOTTISH QUALIFICATIONS AUTHORITY NATIONAL CERTIFICATE MODULE: UNIT SPECIFICATION GENERAL INFORMATION -Module Number- 8210014 -Session- 1994-95 -Superclass- VF -Title- DRAWING SKILLS: TECHNICAL DRAUGHTING
More informationAcceptable Work for Registration as a Registered Lifting Machinery Inspector (RegLMI) E C S A
POLICY STATEMENT R2/1J Acceptable Work for Registration as a Registered Lifting Machinery Inspector (RegLMI) 19/05/2011 E C S A ENGINEERING COUNCIL OF SOUTH AFRICA Private Bag X 691 BRUMA 2026 Water View
More informationISO INTERNATIONAL STANDARD. Petroleum and natural gas industries Offshore production installations Basic surface process safety systems
INTERNATIONAL STANDARD ISO 10418 Second edition 2003-10-01 Petroleum and natural gas industries Offshore production installations Basic surface process safety systems Industries du pétrole et du gaz naturel
More informationINFORMATION SHEET. : Properties Subject to the Slope and Seismic Hazard Zone Protection Act (SSPA) Ordinance
City and County of San Francisco Department of Building Inspection London N. Breed, Mayor Tom C. Hui, S.E., C.B.O., Director INFORMATION SHEET. S-19 DATE : October 2, 2018 CATEGORY SUBJECT : Structural
More informationHigher National Unit specification. General information for centres. Photography: Photojournalism. Unit code: DW8A 35
Higher National Unit specification General information for centres Unit title: Photography: Photojournalism Unit code: DW8A 35 Unit purpose: The Unit is designed to enable the candidate to research, produce,
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 13628-8 First edition 2002-12-15 Petroleum and natural gas industries Design and operation of subsea production systems Part 8: Remotely Operated Vehicle (ROV) interfaces on
More informationRecommended Practice for Flexible Pipe
Recommended Practice for Flexible Pipe ANSI/API RECOMMENDED PRACTICE 17B FOURTH EDITION, JULY 2008 Document includes Technical Corrigendum 1, dated June 2008 ISO 13628-11:2007 (Identical), Petroleum and
More informationDIVISION 1 GENERAL REQUIREMENTS SECTION SUBMITTAL PROCEDURES
DIVISION 1 GENERAL REQUIREMENTS SECTION 01 33 00 PART 1 - GENERAL 1.1 SUMMARY A. This section includes administrative and procedural requirements for submittals required for performance of the work, including
More informationIntroduction to Bowtie Methodology for a Laboratory Setting
Introduction to Bowtie Methodology for a Laboratory Setting ACS 251st National Meeting Division of Chemical Health and Safety Developing, Implementing & Teaching Hazard Assessment Tools Mary Beth Mulcahy,
More informationEngineering Drawing Office Practice; Graphical Engineering Communication Engineering Draughting Skills; Introduction to CAD/CAM or similar Unit
Higher National Unit Specification General information for centres Unit title: Engineering Drawing Unit code: DR1W 34 Unit purpose: This Unit is designed to enable candidates to gain knowledge of current
More informationBulk Electric System Definition Reference Document
Bulk Electric System Definition Reference Document January, 2014 This draft reference document is posted for stakeholder comments prior to being finalized to support implementation of the Phase 2 Bulk
More informationNauticus (Propulsion) - the modern survey scheme for machinery
Nauticus (Propulsion) - the modern survey scheme for machinery Jon Rysst, Department ofsystems and Components, Division of Technology and Products, DetNorske Veritas, N-1322 H0VIK e-mail Jon.Rysst@dnv.com
More informationIGEM/TD/101 Edition 2 Communication 1740 Adoption of pipe systems by a GT management of UIP activities
Communication 1740 Adoption of pipe systems by a GT management of UIP activities Founded 1863 Royal Charter 1929 Patron: Her Majesty the Queen Communication 1740 Adoption of pipe systems by a GT management
More informationINTRODUCTION TO THE RESULTS OF THE IMO PUBLIC CONSULTATION ON ADMINISTRATIVE REQUIREMENTS IN MARITIME REGULATIONS
INTRODUCTION TO THE RESULTS OF THE IMO PUBLIC CONSULTATION ON ADMINISTRATIVE REQUIREMENTS IN MARITIME REGULATIONS This publication presents the main findings and conclusions of the first-ever public consultation
More informationINTERNATIONAL STANDARD
This is a preview - click here to buy the full publication IEC 62032 INTERNATIONAL STANDARD Edition 2.0 2012-06 IEEE Std C57.135 Guide for the Application, Specification, and Testing of Phase-Shifting
More informationAustralian/New Zealand Standard
Australian/New Zealand Standard Quality management and quality assurance Vocabulary This Joint Australian/New Zealand Standard was prepared by Joint Technical Committee QR/7, Quality Terminology. It was
More informationTechnical aspects of Offshore Wind Farms
Consultations of the Guide to OWF Michał Gronert DNV - Independent foundation since 1864 offices countries employees, out of which 76% have academic degree Offshore Wind Energy - compilation of DNV competencies
More informationIECEE OPERATIONAL DOCUMENT
IECEE OD-2025-A Edition 1.1 IECEE OPERATIONAL DOCUMENT IEC System of Conformity Assessment Schemes for Electrotechnical Equipment and Components (IECEE System) CTF - Customers' Testing Facility CTF (CTF
More informationInvitation to take part in the MEP-Scientist Pairing Scheme 2015
Directorate-General for European Parliamentary Research Services Directorate C - Impact Assessment and European Added Value Scientific Foresight Unit (STOA) Invitation to take part in the MEP-Scientist
More informationMARITIME. Digital Twins. for Design, Testing and Verification of Autonomous Systems. Ungraded. 13 June 2016 SAFER, SMARTER, GREENER
MARITIME Digital Twins for Design, Testing and Verification of Autonomous Systems 1 SAFER, SMARTER, GREENER 2011 2 2017 3 Key digital trends shaping the (maritime) industry s future Internet of Things
More informationUNIT Art and Design: Digital Media (SCQF level 6)
National Unit Specification: general information CODE F5CH 12 SUMMARY This Unit is designed to enable the candidate to explore and develop skills in digital media related to art and design disciplines.
More informationDNV GL s Offshore wind cost reduction manifesto
ENERGY DNV GL s Offshore wind cost reduction manifesto Impuls-Vortrag beim Workshop Kostensenkungspotenziale Offshore Windenergie 26 September 2013 1 DNV GL 2014 26 September 2013 SAFER, SMARTER, GREENER
More informationRoad signs Specifications
AS 1743:2018 AS 1743:2018 Road signs Specifications This Australian Standard was prepared by Committee MS-012, Road Signs and Traffic Signals. It was approved on behalf of the Council of Standards Australia
More informationISO INTERNATIONAL STANDARD. Visual examination of the surface condition of investment castings Steel, nickel alloys and cobalt alloys
INTERNATIONAL STANDARD ISO 19959 First edition 2005-04-01 Visual examination of the surface condition of investment castings Steel, nickel alloys and cobalt alloys Examen visuel de l'état de surface des
More informationCircular. Notice of Requirement for Medical Oxygen Cylinder and EPRIB
CCS Circular To: CCS surveyors, Auditors, Marshall Islands Ship owners and Ship managers, Radio inspection company China Classification Society (2011)Circ. No.21 Total No.85 Apr. 21, 2011 (Total pages:
More informationBlast Training Course Guide
Blast Training Course Guide Explosives Awareness Support Shotfiring 4 Hours Those on a mine site, or in a quarry or construction blast environment will benefit from this course. The course is suitable
More informationHow it works and Stakeholder Benefits
UNFC 2009 - Applications in Uranium and Thorium Resources: Focus on Comprehensive Extraction How it works and Stakeholder Benefits David MacDonald Santiago 9-12 July 2013 Stakeholders of our reported resources
More informationNURTURING OFFSHORE WIND MARKETS GOOD PRACTICES FOR INTERNATIONAL STANDARDISATION
NURTURING OFFSHORE WIND MARKETS GOOD PRACTICES FOR INTERNATIONAL STANDARDISATION Summary for POLICY MAKERS SUMMARY FOR POLICY MAKERS The fast pace of offshore wind development has resulted in remarkable
More informationEXTRAORDINARY INNOVATION PROJECT. Going remote. Rethinking offshore operations SAFER, SMARTER, GREENER
Going remote EXTRAORDINARY INNOVATION PROJECT Rethinking offshore operations SAFER, SMARTER, GREENER 2 The situation today Extraordinary Innovation Project Extraordinary innovation project The situation
More informationCommercial Human Spaceflight: Self-regulation is the Future
Commercial Human Spaceflight: Self-regulation is the Future By T. Sgobba IAASS International Association for the Advancement of Space Safety 1 Taking a page from maritime practice International Association
More informationTransportation Research Board National Academy of Sciences Committee on Naval Engineering in the 21 st Century. Washington, DC 12 January 2010
Transportation Research Board National Academy of Sciences Committee on Naval Engineering in the 21 st Century Washington, DC 12 January 2010 Workshop: Examining the Science and Technology Enterprise in
More informationCTF - Customers' Testing Facility
IECEE OD-2048-F2:2017 IEC 2017 1 Ed.1.0 CTF - Customers' Testing Facility CTF Assessment Report (CTF Stages 1 and 2) CTF name CTF address, country Date of assessment: yyyy-mm-dd Ed.1.0
More informationUNIT Computer Aided Draughting (CAD) for Engineers (SCQF level 5)
National Unit Specification: general information CODE F5H4 11 SUMMARY This Unit may form part of a National Qualification Group Award or may be offered on a free standing basis. This largely practical
More information