Enhanced Low Dose Rate Sensitivity (ELDRS) Radiation Testing of the RH1814MW Quad Op Amp for Linear Technology
|
|
- Clemence Sherman
- 5 years ago
- Views:
Transcription
1 Enhanced Low Dose Rate Sensitivity (ELDRS) Radiation Testing of the RH1814MW Quad Op Amp for Linear Technology Customer: Linear Technology (PO 57472L) RAD Job Number: Part Type Tested: Linear Technology RH1814MW Quad Op Amp Commercial Part Number: RH1814MW Traceability Information: Fab Lot# WF , Wafer# 2, Assembly Lot# Information obtained from Linear Technology PO#57472L. Date code marking on the package is 1024A, see Appendix A for a photograph of the device and part markings. Quantity of Units: 12 units total, 5 units for biased irradiation, 5 units for unbiased irradiation and 2 control units. Serial numbers 295 to 298 and 300 were biased during irradiation, serial numbers 301, 302, 304 to 306 were unbiased during irradiation and serial numbers 307 and 308 were used as the controls. See Appendix B for the radiation bias connection table. External Traveler: None Required Pre-Irradiation Burn-In: Burn-In performed by Linear Technology prior to receipt by RAD. TID Dose Rate and Test Increments: 10mrad(Si)/s with readings at pre-irradiation, 10, 20, 30, 40, and 50 krad(si). TID Overtest and Post-Irradiation : No overtest. 24-hour room temperature anneal followed by a 168- hour 100 C anneal. Both anneals shall be performed in the same electrical bias condition as the irradiations. Electrical measurements shall be made following each anneal increment. TID Test Standard: MIL-STD-883H, Method , Condition D TID Electrical Test Conditions: Pre-irradiation, and within one hour following each radiation exposure. Hardware and Software: LTS2020 Automated Tester, Entity ID TS04, Calibration Date: , Calibration Due LTS2101 Family Board, Entity ID FB02. LTS0600 Test Fixture, Entity ID TF03. RH1814W BGSS DUT Board. Test Program: RH1814W.SRC Facility and Radiation Source: Longmire Laboratories, Colorado Springs, CO using the GB-150 low dose rate Co60 source. Dosimetry performed by Air Ionization Chamber (AIC) traceable to NIST. RAD s dosimetry has been audited by DSCC and RAD has been awarded Laboratory Suitability for MIL- STD-750 TM Irradiation and Test Temperature: Ambient room temperature for irradiation and test controlled to 24 C ± 6 C per MIL-STD-883. Low Dose Rate Test Result: PASSED. The units showed no significant degradation with total dose. All parameters remained within their datasheet specifications to the maximum dose level tested of 50krad(Si). Further the units do not exhibit ELDRS as defined in the current test method. 1
2 1.0. Overview and Background It is well known that total dose ionizing radiation can cause parametric degradation and ultimately functional failure in electronic devices. The damage occurs via electron-hole pair production, transport and trapping in the dielectric regions. In advanced CMOS technology nodes (0.6µm and smaller) the bulk of the damage is manifested in the thicker isolation regions, such as shallow trench or local oxidation of silicon (LOCOS) oxides (also known as "birds-beak" oxides). However, many linear and mixed signal devices that utilize bipolar minority carrier elements exhibit an enhanced low dose rate sensitivity (ELDRS). At this time there is no known or accepted a priori method for predicting susceptibility to ELDRS or simulating the low dose rate sensitivity with a "conventional" room temperature rad(Si)/s irradiation (Condition A in MIL-STD-883 TM ). Over the past 10 years a number of accelerating techniques have been examined, including an elevated temperature anneal, such as that used for MOS devices (see ASTM-F-1892 for more technical details) and irradiating at various temperatures. However, none of these techniques have proven useful across the wide variety of linear and/or mixed signal devices used in spaceborne applications. The latest requirement incorporated in MIL-STD-883 TM 1019 requires that devices that could potentially exhibit ELDRS "shall be tested either at the intended application dose rate, at a prescribed low dose rate to an overtest radiation level, or with an accelerated test such as an elevated temperature irradiation test that includes a parameter delta design margin". While the recently released MIL-STD- 883 TM 1019 allows for accelerated testing, the requirements for this are to essentially perform a low dose rate ELDRS test to verify the suitability of the acceleration method on the component of interest before the acceleration technique can be instituted. Based on the limitations of accelerated testing and to meet the requirements of MIL-STD-883 TM Condition D, we have performed a low dose rate test at 10mrad(Si)/s Radiation Test Apparatus The low dose rate testing described in this final report was performed using the facilities at Radiation Assured Devices' Longmire Laboratories in Colorado Springs, CO. The low dose rate source is a GB- 150 irradiator modified to provide a panoramic exposure. The Co-60 rods are held in the base of the irradiator heavily shielded by lead. During the irradiation exposures the rod is raised by an electronic timer/controller and the exposure is performed in air. The dose rate for this irradiator in this configuration ranges from approximately 1mrad(Si)/s to a maximum of approximately 50rad(Si)/s, determined by the distance from the source. For low dose rate testing described in this report, the devices are placed approximately 2-meters from the Co-60 rods. The irradiator calibration is maintained by ' Longmire Laboratories using air ionization chamber (AIC) dosimetry traceable to the National Institute of Standards and Technology (NIST). Figure 2.1 shows a photograph of the GB-150 Co-60 irradiator at RAD's Longmire Laboratory facility. 2
3 Figure 2.1. ' Co-60 irradiator. The dose rate is obtained by positioning the device-under-test at a fixed distance from the gamma cell. The dose rate for this irradiator varies from approximately 50rad(Si)/s close to the rods down to <1mrad(Si)/s at a distance of approximately 4-meters. 3
4 3.0. Radiation Test Conditions The RH1814MW Quad Operational Amplifier described in this final report was irradiated using a split 5V supply and with all pins tied to ground, that is biased and unbiased. See Appendix B for details on the biasing conditions during radiation exposure. In our opinion, this bias circuit satisfies the requirements of MIL-STD-883H TM Section Bias and Loading Conditions which states "The bias applied to the test devices shall be selected to produce the greatest radiation induced damage or the worst-case damage for the intended application, if known. While maximum voltage is often worst case some bipolar linear device parameters (e.g. input bias current or maximum output load current) exhibit more degradation with 0 V bias." The devices were irradiated to a maximum total ionizing dose level of 50krad(Si) with incremental readings at 10krad(Si), 20krad(Si), 30krad(Si) and 40krad(Si). Electrical testing occurred within one hour following the end of each irradiation segment. For intermediate irradiations, the units were tested and returned to total dose exposure within two ours from the end of the previous radiation increment. The radiation exposure bias board was positioned in the Co-60 cell to provide the targeted dose rate of 10mrad(Si)/s and was located inside a lead-aluminum enclosure. The lead-aluminum enclosure is required under MIL-STD-883H TM Section 3.4 that reads as follows: "Lead/Aluminum (Pb/Al) container. Test specimens shall be enclosed in a Pb/Al container to minimize dose enhancement effects caused by low-energy, scattered radiation. A minimum of 1.5 mm Pb, surrounding an inner shield of at least 0.7 mm Al, is required. This Pb/Al container produces an approximate charged particle equilibrium for Si and for TLDs such as CaF2. The radiation field intensity shall be measured inside the Pb/Al container (1) initially, (2) when the source is changed, or (3) when the orientation or configuration of the source, container, or test-fixture is changed. This measurement shall be performed by placing a dosimeter (e.g., a TLD) in the device-irradiation container at the approximate test-device position. If it can be demonstrated that low energy scattered radiation is small enough that it will not cause dosimetry errors due to dose enhancement, the Pb/Al container may be omitted". The final dose rate within the lead-aluminum box was determined based on TLD dosimetry measurements just prior to the beginning of the total dose irradiations. The final dose rate for this work was 10mrad(Si)/s with a precision of ±5%. 4
5 4.0. Tested Parameters During the radiation lot acceptance testing the following pre- and post-irradiation electrical parameters were measured: 1. Positive Supply Current 2. Negative Supply Current 3. Input Offset Voltage (Op Amp 1-4) 4. Input Offset Current (Op Amp 1-4) 5. + Input Bias Current (Op Amp 1-4) 6. - Input Bias Current (Op Amp 1-4) 7. CMRR (Op Amp 1-4) 8. PSRR (Op Amp 1-4) 9. Large Signal Voltage Gain RL=500 (Op Amp 1-4) 10. Large Signal Voltage Gain RL=100 (Op Amp 1-4) 11. Channel Separation (Op Amp 1-4, all permutations) 12. Output Voltage Swing High RL=500 (Op Amp 1-4) 13. Output Voltage Swing High RL=100 (Op Amp 1-4) 14. Output Voltage Swing Low RL=500 (Op Amp 1-4) 15. Output Voltage Swing Low RL=100 (Op Amp 1-4) 16. Maximum Output Source Current (Op Amp 1-4) 17. Maximum Output Sink Current (Op Amp 1-4) 18. Positive Short-Circuit Current (Op Amp 1-4) 19. Negative Short-Circuit Current (Op Amp 1-4) The parametric data was obtained as "read and record" and all the raw data plus an attributes summary are contained in this report as well as in a separate Excel file. The attributes data contains the average, standard deviation and the average with the KTL values applied. The KTL value used in this work is per MIL-HDBK-814 using one sided tolerance limits of 90/90 and a 5-piece sample size. The 90/90 KTL values were selected to match the statistical levels specified in the MIL-PRF sampling plan for the qualification of a radiation hardness assured (RHA) component. Note that the following criteria must be met for a device to pass the low dose rate test: following the radiation exposure each of the 5 pieces irradiated under electrical bias shall pass the specification value. The units irradiated without electrical bias and the KTL statistics are included in this report for reference only. If any of the 5 pieces irradiated under electrical bias exceed the datasheet specifications, then the lot could be logged as a failure. Further, MIL-STD-883H, TM Section Characterization test to determine if a part exhibits ELDRS' states the following: Select a minimum random sample of 21 devices from a population representative of recent production runs. Smaller sample sizes may be used if agreed upon between the parties to the test. All of the selected devices shall have undergone appropriate elevated temperature reliability screens, e.g. burn-in and high temperature storage life. Divide the samples into 5
6 four groups of 5 each and use the remaining part for a control. Perform pre-irradiation electrical characterization on all parts assuring that they meet the Group A electrical tests. Irradiate 5 samples under a 0 volt bias and another 5 under the irradiation bias given in the acquisition specification at rad(si)/s and room temperature. Irradiate 5 samples under a 0 volt bias and another 5 under irradiation bias given in the acquisition specification at < 10mrad(Si)/s and room temperature. Irradiate all samples to the same dose levels, including 0.5 and 1.0 times the anticipated specification dose, and repeat the electrical characterization on each part at each dose level. Post irradiation electrical measurements shall be performed per paragraph 3.10 where the low dose rate test is considered Condition D. Calculate the radiation induced change in each electrical parameter ( para) for each sample at each radiation level. Calculate the ratio of the median para at low dose rate to the median para at high dose rate for each irradiation bias group at each total dose level. If this ratio exceeds 1.5 for any of the most sensitive parameters then the part is considered to be ELDRS susceptible. This test does not apply to parameters which exhibit changes that are within experimental error or whose values are below the pre-irradiation electrical specification limits at low dose rate at the specification dose. Therefore, the data in this report can be analyzed along with the high dose rate report titled "Total Ionizing Dose (TID) Radiation Testing of the RH1814MW Quad Op Amp for Linear Technology" to demonstrate that these parts do not exhibit ELDRS as defined in the current test method. 6
7 5.0. ELDRS Test Results Based on this criterion the RH1814MW Quad Operational Amplifier (from the lot date code identified on the first page of this test report) PASSED the enhanced low dose rate sensitivity test to the maximum tested dose level of 50krad(Si) with all parameters remaining within their datasheet specifications. Figures 5.1 through show plots of all the measured parameters versus total ionizing dose while Tables show the corresponding raw data for each of these parameters. In the data plots the solid diamonds are the average of the measured data points for the sample irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the units irradiated with all pins tied to ground. The black lines (solid or dashed) are the average of the data points after application of the KTL statistics on the sample irradiated in the biased condition while the shaded lines (solid or dashed) are the average of the data points after application of the KTL statistics on the sample irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. In addition to the radiation test results, the data plots and tables described above contain anneal data. The anneals are performed to better understand the underlying physical mechanisms responsible for radiation-induced parametric shifts and are not part of the criteria used to establish whether or not the lot passes or fails the low dose rate test. In all cases the parts either improved or exhibited no change during the anneal. The control units, as expected, show no significant changes to any of the parameters. Therefore we can conclude that the electrical testing remained in control throughout the duration of the tests and the observed degradation was due to the radiation exposure. Appendix D lists the figures used in this section to facilitate the location of a particular parameter. 7
8 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX 1.50E-02 Positive Supply (A) 1.45E E E E E E E hr hr 70 Figure 5.1. Plot of Positive Supply (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 8
9 Table 5.1. Raw data for Positive Supply (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Supply (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased 1.27E E E E E E E E-02 Std Dev Biased 3.41E E E E E E E E-04 Ps90%/90% (+KTL) Biased 1.37E E E E E E E E-02 Ps90%/90% (-KTL) Biased 1.18E E E E E E E E-02 Un-Biased Statistics Average Un-Biased 1.23E E E E E E E E-02 Std Dev Un-Biased 7.72E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 1.44E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased 1.01E E E E E E E E-02 Specification MAX 1.44E E E E E E E E-02 Status PASS PASS PASS N/A N/A PASS PASS PASS 9
10 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN -1.20E-02 Negative Supply (A) -1.25E E E E E E hr hr 70 Figure 5.2. Plot of Negative Supply (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 10
11 Table 5.2. Raw data for Negative Supply (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Supply (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased -1.28E E E E E E E E-02 Std Dev Biased 3.42E E E E E E E E-04 Ps90%/90% (+KTL) Biased -1.18E E E E E E E E-02 Ps90%/90% (-KTL) Biased -1.37E E E E E E E E-02 Un-Biased Statistics Average Un-Biased -1.23E E E E E E E E-02 Std Dev Un-Biased 7.71E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased -1.02E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased -1.44E E E E E E E E-02 Specification MIN -1.44E E E E E E E E-02 Status PASS PASS PASS N/A N/A PASS PASS PASS 11
12 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 5.00E-03 Input Offset #1 (V) 4.00E E E E E E E E E E hr hr 70 Figure 5.3. Plot of Input Offset #1 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 12
13 Table 5.3. Raw data for Input Offset #1 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset #1 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-06 Biased Statistics Average Biased -1.75E E E E E E E E-04 Std Dev Biased 3.27E E E E E E E E-04 Ps90%/90% (+KTL) Biased 7.22E E E E E E E E-04 Ps90%/90% (-KTL) Biased -1.07E E E E E E E E-03 Un-Biased Statistics Average Un-Biased -9.86E E E E E E E E-04 Std Dev Un-Biased 4.93E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 1.25E E E E E E E E-03 Ps90%/90% (-KTL) Un-Biased -1.45E E E E E E E E-03 Specification MIN -1.50E E E E E E E E-03 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 1.50E E E E E E E E-03 Status PASS PASS PASS N/A N/A PASS PASS PASS 13
14 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 5.00E-03 Input Offset #2 (V) 4.00E E E E E E E E E E hr hr 70 Figure 5.4. Plot of Input Offset #2 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 14
15 Table 5.4. Raw data for Input Offset #2 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset #2 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-04 Biased Statistics Average Biased -2.47E E E E E E E E-04 Std Dev Biased 3.66E E E E E E E E-04 Ps90%/90% (+KTL) Biased 7.57E E E E E E E E-04 Ps90%/90% (-KTL) Biased -1.25E E E E E E E E-03 Un-Biased Statistics Average Un-Biased -1.35E E E E E E E E-04 Std Dev Un-Biased 2.19E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 4.66E E E E E E E E-04 Ps90%/90% (-KTL) Un-Biased -7.36E E E E E E E E-04 Specification MIN -1.50E E E E E E E E-03 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 1.50E E E E E E E E-03 Status PASS PASS PASS N/A N/A PASS PASS PASS 15
16 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 5.00E-03 Input Offset #3 (V) 4.00E E E E E E E E E E hr hr 70 Figure 5.5. Plot of Input Offset #3 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 16
17 Table 5.5. Raw data for Input Offset #3 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset #3 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-04 Biased Statistics Average Biased -2.03E E E E E E E E-04 Std Dev Biased 5.75E E E E E E E E-04 Ps90%/90% (+KTL) Biased 1.37E E E E E E E E-03 Ps90%/90% (-KTL) Biased -1.78E E E E E E E E-03 Un-Biased Statistics Average Un-Biased -1.78E E E E E E E E-04 Std Dev Un-Biased 3.06E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 6.62E E E E E E E E-04 Ps90%/90% (-KTL) Un-Biased -1.02E E E E E E E E-03 Specification MIN -1.50E E E E E E E E-03 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 1.50E E E E E E E E-03 Status PASS PASS PASS N/A N/A PASS PASS PASS 17
18 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 5.00E-03 Input Offset #4 (V) 4.00E E E E E E E E E E hr hr 70 Figure 5.6. Plot of Input Offset #4 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 18
19 Table 5.6. Raw data for Input Offset #4 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset #4 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-04 Biased Statistics Average Biased -1.27E E E E E E E E-04 Std Dev Biased 1.83E E E E E E E E-04 Ps90%/90% (+KTL) Biased 3.74E E E E E E E E-04 Ps90%/90% (-KTL) Biased -6.29E E E E E E E E-04 Un-Biased Statistics Average Un-Biased 1.68E E E E E E E E-04 Std Dev Un-Biased 2.35E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 8.12E E E E E E E E-04 Ps90%/90% (-KTL) Un-Biased -4.75E E E E E E E E-04 Specification MIN -1.50E E E E E E E E-03 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 1.50E E E E E E E E-03 Status PASS PASS PASS N/A N/A PASS PASS PASS 19
20 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 1.00E-06 Input Offset #1 (A) 8.00E E E E E E E E E E hr hr 70 Figure 5.7. Plot of Input Offset #1 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 20
21 Table 5.7. Raw data for Input Offset #1 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset #1 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-08 Biased Statistics Average Biased 1.23E E E E E E E E+00 Std Dev Biased 5.07E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.51E E E E E E E E+00 Ps90%/90% (-KTL) Biased -1.27E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 1.30E E E E E E E E-09 Std Dev Un-Biased 6.09E E E E E E E E-09 Ps90%/90% (+KTL) Un-Biased 1.80E E E E E E E E-08 Ps90%/90% (-KTL) Un-Biased -1.54E E E E E E E E-08 Specification MIN -4.00E E E E E E E E-07 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-07 Status PASS PASS PASS N/A N/A PASS PASS PASS 21
22 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 1.00E-06 Input Offset #2 (A) 8.00E E E E E E E E E E hr hr 70 Figure 5.8. Plot of Input Offset #2 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 22
23 Table 5.8. Raw data for Input Offset #2 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset #2 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 2.11E E E E E E E E-09 Std Dev Biased 9.95E E E E E E E E-08 Ps90%/90% (+KTL) Biased 2.94E E E E E E E E-08 Ps90%/90% (-KTL) Biased -2.52E E E E E E E E-08 Un-Biased Statistics Average Un-Biased 9.56E E E E E E E E+00 Std Dev Un-Biased 4.72E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.39E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased -1.20E E E E E E E E+00 Specification MIN -4.00E E E E E E E E-07 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-07 Status PASS PASS PASS N/A N/A PASS PASS PASS 23
24 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 1.00E-06 Input Offset #3 (A) 8.00E E E E E E E E E E hr hr 70 Figure 5.9. Plot of Input Offset #3 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 24
25 Table 5.9. Raw data for Input Offset #3 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset #3 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-08 Biased Statistics Average Biased 2.00E E E E E E E E+00 Std Dev Biased 2.35E E E E E E E E+00 Ps90%/90% (+KTL) Biased 8.46E E E E E E E E+00 Ps90%/90% (-KTL) Biased -4.45E E E E E E E E+00 Un-Biased Statistics Average Un-Biased -1.19E E E E E E E E+00 Std Dev Un-Biased 3.82E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 9.29E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased -1.17E E E E E E E E+00 Specification MIN -4.00E E E E E E E E-07 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-07 Status PASS PASS PASS N/A N/A PASS PASS PASS 25
26 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 1.00E-06 Input Offset #4 (A) 8.00E E E E E E E E E E hr hr 70 Figure Plot of Input Offset #4 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 26
27 Table Raw data for Input Offset #4 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset #4 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 3.95E E E E E E E E-09 Std Dev Biased 1.08E E E E E E E E-09 Ps90%/90% (+KTL) Biased 3.36E E E E E E E E-08 Ps90%/90% (-KTL) Biased -2.57E E E E E E E E-08 Un-Biased Statistics Average Un-Biased 8.87E E E E E E E E-09 Std Dev Un-Biased 1.12E E E E E E E E-09 Ps90%/90% (+KTL) Un-Biased 3.97E E E E E E E E-08 Ps90%/90% (-KTL) Un-Biased -2.19E E E E E E E E-08 Specification MIN -4.00E E E E E E E E-07 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-07 Status PASS PASS PASS N/A N/A PASS PASS PASS 27
28 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Positive Input Bias #1 (A) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Positive Input Bias #1 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 28
29 Table Raw data for Positive Input Bias #1 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Input Bias #1 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-07 Biased Statistics Average Biased 1.62E E E E E E E E-07 Std Dev Biased 8.37E E E E E E E E-08 Ps90%/90% (+KTL) Biased 1.85E E E E E E E E-07 Ps90%/90% (-KTL) Biased 1.39E E E E E E E E-07 Un-Biased Statistics Average Un-Biased 1.46E E E E E E E E-07 Std Dev Un-Biased 1.82E E E E E E E E-08 Ps90%/90% (+KTL) Un-Biased 1.96E E E E E E E E-07 Ps90%/90% (-KTL) Un-Biased 9.62E E E E E E E E-07 Specification MIN -4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS 29
30 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Positive Input Bias #2 (A) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Positive Input Bias #2 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 30
31 Table Raw data for Positive Input Bias #2 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Input Bias #2 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-07 Biased Statistics Average Biased 1.56E E E E E E E E-07 Std Dev Biased 1.52E E E E E E E E-08 Ps90%/90% (+KTL) Biased 1.98E E E E E E E E-07 Ps90%/90% (-KTL) Biased 1.14E E E E E E E E-07 Un-Biased Statistics Average Un-Biased 1.48E E E E E E E E-07 Std Dev Un-Biased 1.10E E E E E E E E-09 Ps90%/90% (+KTL) Un-Biased 1.78E E E E E E E E-07 Ps90%/90% (-KTL) Un-Biased 1.18E E E E E E E E-07 Specification MIN -4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS 31
32 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Positive Input Bias #3 (A) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Positive Input Bias #3 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 32
33 Table Raw data for Positive Input Bias #3 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Input Bias #3 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-07 Biased Statistics Average Biased 1.60E E E E E E E E-07 Std Dev Biased 2.35E E E E E E E E-08 Ps90%/90% (+KTL) Biased 2.24E E E E E E E E-07 Ps90%/90% (-KTL) Biased 9.57E E E E E E E E-08 Un-Biased Statistics Average Un-Biased 1.52E E E E E E E E-07 Std Dev Un-Biased 1.30E E E E E E E E-08 Ps90%/90% (+KTL) Un-Biased 1.88E E E E E E E E-07 Ps90%/90% (-KTL) Un-Biased 1.16E E E E E E E E-07 Specification MIN -4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS 33
34 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Positive Input Bias #4 (A) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Positive Input Bias #4 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 34
35 Table Raw data for Positive Input Bias #4 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Input Bias #4 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-07 Biased Statistics Average Biased 1.64E E E E E E E E-07 Std Dev Biased 8.94E E E E E E E E-09 Ps90%/90% (+KTL) Biased 1.89E E E E E E E E-07 Ps90%/90% (-KTL) Biased 1.39E E E E E E E E-07 Un-Biased Statistics Average Un-Biased 1.50E E E E E E E E-07 Std Dev Un-Biased 1.41E E E E E E E E-09 Ps90%/90% (+KTL) Un-Biased 1.89E E E E E E E E-07 Ps90%/90% (-KTL) Un-Biased 1.11E E E E E E E E-07 Specification MIN -4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS 35
36 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Negative Input Bias #1 (A) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Negative Input Bias #1 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 36
37 Table Raw data for Negative Input Bias #1 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Input Bias #1 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-07 Biased Statistics Average Biased 1.60E E E E E E E E-07 Std Dev Biased 1.00E E E E E E E E-08 Ps90%/90% (+KTL) Biased 1.87E E E E E E E E-07 Ps90%/90% (-KTL) Biased 1.33E E E E E E E E-07 Un-Biased Statistics Average Un-Biased 1.46E E E E E E E E-07 Std Dev Un-Biased 1.14E E E E E E E E-08 Ps90%/90% (+KTL) Un-Biased 1.77E E E E E E E E-07 Ps90%/90% (-KTL) Un-Biased 1.15E E E E E E E E-07 Specification MIN -4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS 37
38 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Negative Input Bias #2 (A) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Negative Input Bias #2 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 38
39 Table Raw data for Negative Input Bias #2 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Input Bias #2 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-07 Biased Statistics Average Biased 1.54E E E E E E E E-07 Std Dev Biased 1.52E E E E E E E E-08 Ps90%/90% (+KTL) Biased 1.96E E E E E E E E-07 Ps90%/90% (-KTL) Biased 1.12E E E E E E E E-08 Un-Biased Statistics Average Un-Biased 1.48E E E E E E E E-07 Std Dev Un-Biased 1.48E E E E E E E E-08 Ps90%/90% (+KTL) Un-Biased 1.89E E E E E E E E-07 Ps90%/90% (-KTL) Un-Biased 1.07E E E E E E E E-07 Specification MIN -4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS 39
40 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Negative Input Bias #3 (A) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Negative Input Bias #3 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 40
41 Table Raw data for Negative Input Bias #3 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Input Bias #3 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-07 Biased Statistics Average Biased 1.58E E E E E E E E-07 Std Dev Biased 2.17E E E E E E E E-08 Ps90%/90% (+KTL) Biased 2.17E E E E E E E E-07 Ps90%/90% (-KTL) Biased 9.86E E E E E E E E-08 Un-Biased Statistics Average Un-Biased 1.54E E E E E E E E-07 Std Dev Un-Biased 1.14E E E E E E E E-08 Ps90%/90% (+KTL) Un-Biased 1.85E E E E E E E E-07 Ps90%/90% (-KTL) Un-Biased 1.23E E E E E E E E-07 Specification MIN -4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS 41
42 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Negative Input Bias #4 (A) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Negative Input Bias #4 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 42
43 Table Raw data for Negative Input Bias #4 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Input Bias #4 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-07 Biased Statistics Average Biased 1.62E E E E E E E E-07 Std Dev Biased 8.37E E E E E E E E-09 Ps90%/90% (+KTL) Biased 1.85E E E E E E E E-07 Ps90%/90% (-KTL) Biased 1.39E E E E E E E E-07 Un-Biased Statistics Average Un-Biased 1.42E E E E E E E E-07 Std Dev Un-Biased 1.48E E E E E E E E-08 Ps90%/90% (+KTL) Un-Biased 1.83E E E E E E E E-07 Ps90%/90% (-KTL) Un-Biased 1.01E E E E E E E E-07 Specification MIN -4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS 43
44 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Common Mode Rejection #1 (db) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Common Mode Rejection #1 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 44
45 Table Raw data for Common Mode Rejection #1 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Common Mode Rejection #1 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+01 Biased Statistics Average Biased 8.92E E E E E E E E+01 Std Dev Biased 7.06E E E E E E E E+00 Ps90%/90% (+KTL) Biased 9.12E E E E E E E E+01 Ps90%/90% (-KTL) Biased 8.73E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 8.94E E E E E E E E+01 Std Dev Un-Biased 9.90E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 9.21E E E E E E E E+01 Ps90%/90% (-KTL) Un-Biased 8.67E E E E E E E E+01 Specification MIN 7.50E E E E E E E E+01 Status PASS PASS PASS N/A N/A PASS PASS PASS 45
46 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Common Mode Rejection #2 (db) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Common Mode Rejection #2 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 46
47 Table Raw data for Common Mode Rejection #2 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Common Mode Rejection #2 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+01 Biased Statistics Average Biased 8.90E E E E E E E E+01 Std Dev Biased 1.84E E E E E E E E+00 Ps90%/90% (+KTL) Biased 9.41E E E E E E E E+01 Ps90%/90% (-KTL) Biased 8.39E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 9.02E E E E E E E E+01 Std Dev Un-Biased 1.11E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 9.33E E E E E E E E+01 Ps90%/90% (-KTL) Un-Biased 8.72E E E E E E E E+01 Specification MIN 7.50E E E E E E E E+01 Status PASS PASS PASS N/A N/A PASS PASS PASS 47
48 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Common Mode Rejection #3 (db) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Common Mode Rejection #3 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 48
49 Table Raw data for Common Mode Rejection #3 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Common Mode Rejection #3 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+01 Biased Statistics Average Biased 9.00E E E E E E E E+01 Std Dev Biased 1.77E E E E E E E E+00 Ps90%/90% (+KTL) Biased 9.49E E E E E E E E+01 Ps90%/90% (-KTL) Biased 8.52E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 8.97E E E E E E E E+01 Std Dev Un-Biased 1.41E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 9.35E E E E E E E E+01 Ps90%/90% (-KTL) Un-Biased 8.58E E E E E E E E+01 Specification MIN 7.50E E E E E E E E+01 Status PASS PASS PASS N/A N/A PASS PASS PASS 49
50 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Common Mode Rejection #4 (db) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Common Mode Rejection #4 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 50
51 Table Raw data for Common Mode Rejection #4 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Common Mode Rejection #4 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+01 Biased Statistics Average Biased 8.96E E E E E E E E+01 Std Dev Biased 1.89E E E E E E E E+00 Ps90%/90% (+KTL) Biased 9.48E E E E E E E E+01 Ps90%/90% (-KTL) Biased 8.44E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 9.07E E E E E E E E+01 Std Dev Un-Biased 1.22E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 9.40E E E E E E E E+01 Ps90%/90% (-KTL) Un-Biased 8.73E E E E E E E E+01 Specification MIN 7.50E E E E E E E E+01 Status PASS PASS PASS N/A N/A PASS PASS PASS 51
52 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 1.20E+02 Power Supply Rejection Ratio #1 (db) 1.00E E E E E E hr hr 70 Figure Plot of Power Supply Rejection Ratio #1 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 52
53 Table Raw data for Power Supply Rejection Ratio #1 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Power Supply Rejection Ratio #1 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.01E E E E E E E E+01 Std Dev Biased 5.86E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.17E E E E E E E E+02 Ps90%/90% (-KTL) Biased 8.46E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.01E E E E E E E E+02 Std Dev Un-Biased 5.38E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.16E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 8.67E E E E E E E E+01 Specification MIN 7.80E E E E E E E E+01 Status PASS PASS PASS N/A N/A PASS PASS PASS 53
54 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 1.20E+02 Power Supply Rejection Ratio #2 (db) 1.00E E E E E E hr hr 70 Figure Plot of Power Supply Rejection Ratio #2 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 54
55 Table Raw data for Power Supply Rejection Ratio #2 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Power Supply Rejection Ratio #2 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 9.97E E E E E E E E+01 Std Dev Biased 3.40E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.09E E E E E E E E+02 Ps90%/90% (-KTL) Biased 9.04E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.01E E E E E E E E+02 Std Dev Un-Biased 8.02E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.23E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 7.92E E E E E E E E+01 Specification MIN 7.80E E E E E E E E+01 Status PASS PASS PASS N/A N/A PASS PASS PASS 55
56 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 1.20E+02 Power Supply Rejection Ratio #3 (db) 1.00E E E E E E hr hr 70 Figure Plot of Power Supply Rejection Ratio #3 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 56
57 Table Raw data for Power Supply Rejection Ratio #3 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Power Supply Rejection Ratio #3 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.06E E E E E E E E+02 Std Dev Biased 1.22E E E E E E E E+01 Ps90%/90% (+KTL) Biased 1.39E E E E E E E E+02 Ps90%/90% (-KTL) Biased 7.20E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 9.87E E E E E E E E+01 Std Dev Un-Biased 6.68E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.17E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 8.04E E E E E E E E+01 Specification MIN 7.80E E E E E E E E+01 Status PASS PASS PASS N/A N/A PASS PASS PASS 57
58 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 1.20E+02 Power Supply Rejection Ratio #4 (db) 1.00E E E E E E hr hr 70 Figure Plot of Power Supply Rejection Ratio #4 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 58
59 Table Raw data for Power Supply Rejection Ratio #4 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Power Supply Rejection Ratio #4 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+01 Biased Statistics Average Biased 1.06E E E E E E E E+02 Std Dev Biased 6.13E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.23E E E E E E E E+02 Ps90%/90% (-KTL) Biased 8.91E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.09E E E E E E E E+02 Std Dev Un-Biased 7.13E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.28E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 8.94E E E E E E E E+01 Specification MIN 7.80E E E E E E E E+01 Status PASS PASS PASS N/A N/A PASS PASS PASS 59
60 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Large Signal Voltage RL=500 #1 (V/mV) 5.00E E E E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased Specification MIN hr hr 70 Figure Plot of Large Signal Voltage RL=500 #1 (V/mV) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 60
61 Table Raw data for Large Signal Voltage RL=500 #1 (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Large Signal Voltage RL=500 #1 (V/mV) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 4.40E E E E E E E E+00 Std Dev Biased 7.96E E E E E E E E-02 Ps90%/90% (+KTL) Biased 4.62E E E E E E E E+00 Ps90%/90% (-KTL) Biased 4.18E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 4.57E E E E E E E E+00 Std Dev Un-Biased 2.64E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 5.29E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 3.85E E E E E E E E+00 Specification MIN 1.50E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 61
62 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Large Signal Voltage RL=500 #2 (V/mV) 5.00E E E E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased Specification MIN hr hr 70 Figure Plot of Large Signal Voltage RL=500 #2 (V/mV) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 62
63 Table Raw data for Large Signal Voltage RL=500 #2 (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Large Signal Voltage RL=500 #2 (V/mV) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 4.40E E E E E E E E+00 Std Dev Biased 7.86E E E E E E E E-01 Ps90%/90% (+KTL) Biased 4.61E E E E E E E E+00 Ps90%/90% (-KTL) Biased 4.18E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 4.48E E E E E E E E+00 Std Dev Un-Biased 1.91E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 5.01E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 3.96E E E E E E E E+00 Specification MIN 1.50E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 63
64 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Large Signal Voltage RL=500 #3 (V/mV) 5.00E E E E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased Specification MIN hr hr 70 Figure Plot of Large Signal Voltage RL=500 #3 (V/mV) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 64
65 Table Raw data for Large Signal Voltage RL=500 #3 (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Large Signal Voltage RL=500 #3 (V/mV) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 4.44E E E E E E E E+00 Std Dev Biased 1.13E E E E E E E E-01 Ps90%/90% (+KTL) Biased 4.75E E E E E E E E+00 Ps90%/90% (-KTL) Biased 4.13E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 4.54E E E E E E E E+00 Std Dev Un-Biased 2.17E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 5.14E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 3.95E E E E E E E E+00 Specification MIN 1.50E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 65
66 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Large Signal Voltage RL=500 #4 (V/mV) 5.00E E E E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased Specification MIN hr hr 70 Figure Plot of Large Signal Voltage RL=500 #4 (V/mV) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 66
67 Table Raw data for Large Signal Voltage RL=500 #4 (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Large Signal Voltage RL=500 #4 (V/mV) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 4.37E E E E E E E E+00 Std Dev Biased 1.01E E E E E E E E-01 Ps90%/90% (+KTL) Biased 4.65E E E E E E E E+00 Ps90%/90% (-KTL) Biased 4.09E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 4.52E E E E E E E E+00 Std Dev Un-Biased 2.41E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 5.18E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 3.86E E E E E E E E+00 Specification MIN 1.50E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 67
68 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Large Signal Voltage RL=100 #1 (V/mV) 4.00E E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased Specification MIN hr hr 70 Figure Plot of Large Signal Voltage RL=100 #1 (V/mV) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 68
69 Table Raw data for Large Signal Voltage RL=100 #1 (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Large Signal Voltage RL=100 #1 (V/mV) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 3.50E E E E E E E E+00 Std Dev Biased 7.94E E E E E E E E-02 Ps90%/90% (+KTL) Biased 3.72E E E E E E E E+00 Ps90%/90% (-KTL) Biased 3.28E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 3.65E E E E E E E E+00 Std Dev Un-Biased 2.15E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 4.24E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 3.06E E E E E E E E+00 Specification MIN 1.00E E E E E E E E-01 Status PASS PASS PASS N/A N/A PASS PASS PASS 69
70 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Large Signal Voltage RL=100 #2 (V/mV) 4.00E E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased Specification MIN hr hr 70 Figure Plot of Large Signal Voltage RL=100 #2 (V/mV) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 70
71 Table Raw data for Large Signal Voltage RL=100 #2 (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Large Signal Voltage RL=100 #2 (V/mV) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 3.49E E E E E E E E+00 Std Dev Biased 7.36E E E E E E E E-01 Ps90%/90% (+KTL) Biased 3.69E E E E E E E E+00 Ps90%/90% (-KTL) Biased 3.29E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 3.57E E E E E E E E+00 Std Dev Un-Biased 1.27E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 3.92E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 3.22E E E E E E E E+00 Specification MIN 1.00E E E E E E E E-01 Status PASS PASS PASS N/A N/A PASS PASS PASS 71
72 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Large Signal Voltage RL=100 #3 (V/mV) 4.00E E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased Specification MIN hr hr 70 Figure Plot of Large Signal Voltage RL=100 #3 (V/mV) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 72
73 Table Raw data for Large Signal Voltage RL=100 #3 (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Large Signal Voltage RL=100 #3 (V/mV) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 3.54E E E E E E E E+00 Std Dev Biased 1.16E E E E E E E E-01 Ps90%/90% (+KTL) Biased 3.86E E E E E E E E+00 Ps90%/90% (-KTL) Biased 3.22E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 3.64E E E E E E E E+00 Std Dev Un-Biased 1.66E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 4.10E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 3.19E E E E E E E E+00 Specification MIN 1.00E E E E E E E E-01 Status PASS PASS PASS N/A N/A PASS PASS PASS 73
74 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Large Signal Voltage RL=100 #4 (V/mV) 4.00E E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased Specification MIN hr hr 70 Figure Plot of Large Signal Voltage RL=100 #4 (V/mV) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 74
75 Table Raw data for Large Signal Voltage RL=100 #4 (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Large Signal Voltage RL=100 #4 (V/mV) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 3.48E E E E E E E E+00 Std Dev Biased 9.60E E E E E E E E-02 Ps90%/90% (+KTL) Biased 3.74E E E E E E E E+00 Ps90%/90% (-KTL) Biased 3.22E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 3.58E E E E E E E E+00 Std Dev Un-Biased 1.63E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 4.03E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 3.14E E E E E E E E+00 Specification MIN 1.00E E E E E E E E-01 Status PASS PASS PASS N/A N/A PASS PASS PASS 75
76 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 1.40E+02 Channel 1:2 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 1:2 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 76
77 Table Raw data for Channel 1:2 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 1:2 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.10E E E E E E E E+02 Std Dev Biased 6.31E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.28E E E E E E E E+02 Ps90%/90% (-KTL) Biased 9.31E E E E E E E E+02 Un-Biased Statistics Average Un-Biased 1.22E E E E E E E E+02 Std Dev Un-Biased 8.62E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.45E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 9.81E E E E E E E E+01 Specification MIN 8.20E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 77
78 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 1.40E+02 Channel 1:3 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 1:3 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 78
79 Table Raw data for Channel 1:3 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 1:3 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.20E E E E E E E E+02 Std Dev Biased 6.65E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.38E E E E E E E E+02 Ps90%/90% (-KTL) Biased 1.01E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.22E E E E E E E E+02 Std Dev Un-Biased 1.60E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.65E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 7.77E E E E E E E E+02 Specification MIN 8.20E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 79
80 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 1.40E+02 Channel 1:4 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 1:4 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 80
81 Table Raw data for Channel 1:4 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 1:4 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.15E E E E E E E E+02 Std Dev Biased 1.56E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.58E E E E E E E E+02 Ps90%/90% (-KTL) Biased 7.26E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.09E E E E E E E E+02 Std Dev Un-Biased 3.74E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.19E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 9.86E E E E E E E E+01 Specification MIN 8.20E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 81
82 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 1.40E+02 Channel 2:1 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 2:1 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 82
83 Table Raw data for Channel 2:1 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 2:1 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.23E E E E E E E E+02 Std Dev Biased 9.66E E E E E E E E+01 Ps90%/90% (+KTL) Biased 1.49E E E E E E E E+02 Ps90%/90% (-KTL) Biased 9.63E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.21E E E E E E E E+02 Std Dev Un-Biased 1.09E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.50E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 9.08E E E E E E E E+01 Specification MIN 8.20E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 83
84 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 1.40E+02 Channel 2:3 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 2:3 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 84
85 Table Raw data for Channel 2:3 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 2:3 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.06E E E E E E E E+02 Std Dev Biased 3.38E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.15E E E E E E E E+02 Ps90%/90% (-KTL) Biased 9.66E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.04E E E E E E E E+02 Std Dev Un-Biased 3.50E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.14E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 9.49E E E E E E E E+01 Specification MIN 8.20E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 85
86 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 1.40E+02 Channel 2:4 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 2:4 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 86
87 Table Raw data for Channel 2:4 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 2:4 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.24E E E E E E E E+02 Std Dev Biased 1.42E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.63E E E E E E E E+02 Ps90%/90% (-KTL) Biased 8.51E E E E E E E E+02 Un-Biased Statistics Average Un-Biased 1.20E E E E E E E E+02 Std Dev Un-Biased 4.89E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.33E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 1.06E E E E E E E E+01 Specification MIN 8.20E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 87
88 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 1.40E+02 Channel 3:1 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 3:1 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 88
89 Table Raw data for Channel 3:1 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 3:1 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.12E E E E E E E E+02 Std Dev Biased 8.46E E E E E E E E+01 Ps90%/90% (+KTL) Biased 1.35E E E E E E E E+02 Ps90%/90% (-KTL) Biased 8.90E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.23E E E E E E E E+02 Std Dev Un-Biased 1.11E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.54E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 9.30E E E E E E E E+01 Specification MIN 8.20E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 89
90 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 1.40E+02 Channel 3:2 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 3:2 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 90
91 Table Raw data for Channel 3:2 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 3:2 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.07E E E E E E E E+02 Std Dev Biased 4.57E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.19E E E E E E E E+02 Ps90%/90% (-KTL) Biased 9.44E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.15E E E E E E E E+02 Std Dev Un-Biased 6.29E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.32E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 9.76E E E E E E E E+02 Specification MIN 8.20E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 91
92 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 1.40E+02 Channel 3:4 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 3:4 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 92
93 Table Raw data for Channel 3:4 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 3:4 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.19E E E E E E E E+02 Std Dev Biased 6.67E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.38E E E E E E E E+02 Ps90%/90% (-KTL) Biased 1.01E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.20E E E E E E E E+02 Std Dev Un-Biased 1.03E E E E E E E E+01 Ps90%/90% (+KTL) Un-Biased 1.48E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 9.18E E E E E E E E+01 Specification MIN 8.20E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 93
94 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 1.20E+02 Channel 4:1 (db) 1.00E E E E E E hr hr 70 Figure Plot of Channel 4:1 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 94
95 Table Raw data for Channel 4:1 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 4:1 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.08E E E E E E E E+02 Std Dev Biased 4.88E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.21E E E E E E E E+02 Ps90%/90% (-KTL) Biased 9.42E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.03E E E E E E E E+02 Std Dev Un-Biased 1.63E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.08E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 9.90E E E E E E E E+01 Specification MIN 8.20E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 95
96 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 1.40E+02 Channel 4:2 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 4:2 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 96
97 Table Raw data for Channel 4:2 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 4:2 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.17E E E E E E E E+02 Std Dev Biased 3.56E E E E E E E E+01 Ps90%/90% (+KTL) Biased 1.27E E E E E E E E+02 Ps90%/90% (-KTL) Biased 1.08E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.18E E E E E E E E+02 Std Dev Un-Biased 5.21E E E E E E E E+01 Ps90%/90% (+KTL) Un-Biased 1.32E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 1.04E E E E E E E E+01 Specification MIN 8.20E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 97
98 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 1.40E+02 Channel 4:3 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 4:3 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 98
99 Table Raw data for Channel 4:3 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 4:3 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.14E E E E E E E E+02 Std Dev Biased 2.81E E E E E E E E+01 Ps90%/90% (+KTL) Biased 1.21E E E E E E E E+02 Ps90%/90% (-KTL) Biased 1.06E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.19E E E E E E E E+02 Std Dev Un-Biased 1.05E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.48E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 9.05E E E E E E E E+01 Specification MIN 8.20E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 99
100 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Output Voltage Swing RL=500 #1 (V) 4.05E E E E E E E E E hr hr 70 Figure Plot of Output Voltage Swing RL=500 #1 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 100
101 Table Raw data for Output Voltage Swing RL=500 #1 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=500 #1 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 4.03E E E E E E E E+00 Std Dev Biased 1.14E E E E E E E E-03 Ps90%/90% (+KTL) Biased 4.03E E E E E E E E+00 Ps90%/90% (-KTL) Biased 4.02E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 4.03E E E E E E E E+00 Std Dev Un-Biased 2.05E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 4.03E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 4.02E E E E E E E E+00 Specification MIN 3.80E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 101
102 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Output Voltage Swing RL=500 #2 (V) 4.05E E E E E E E E E hr hr 70 Figure Plot of Output Voltage Swing RL=500 #2 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 102
103 Table Raw data for Output Voltage Swing RL=500 #2 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=500 #2 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 4.03E E E E E E E E+00 Std Dev Biased 1.14E E E E E E E E-03 Ps90%/90% (+KTL) Biased 4.03E E E E E E E E+00 Ps90%/90% (-KTL) Biased 4.02E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 4.03E E E E E E E E+00 Std Dev Un-Biased 1.52E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 4.03E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 4.02E E E E E E E E+00 Specification MIN 3.80E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 103
104 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Output Voltage Swing RL=500 #3 (V) 4.05E E E E E E E E E hr hr 70 Figure Plot of Output Voltage Swing RL=500 #3 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 104
105 Table Raw data for Output Voltage Swing RL=500 #3 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=500 #3 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 4.03E E E E E E E E+00 Std Dev Biased 1.14E E E E E E E E-03 Ps90%/90% (+KTL) Biased 4.03E E E E E E E E+00 Ps90%/90% (-KTL) Biased 4.02E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 4.03E E E E E E E E+00 Std Dev Un-Biased 1.10E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 4.03E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 4.02E E E E E E E E+00 Specification MIN 3.80E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 105
106 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Output Voltage Swing RL=500 #4 (V) 4.05E E E E E E E E E hr hr 70 Figure Plot of Output Voltage Swing RL=500 #4 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 106
107 Table Raw data for Output Voltage Swing RL=500 #4 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=500 #4 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 4.03E E E E E E E E+00 Std Dev Biased 1.30E E E E E E E E-03 Ps90%/90% (+KTL) Biased 4.03E E E E E E E E+00 Ps90%/90% (-KTL) Biased 4.02E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 4.03E E E E E E E E+00 Std Dev Un-Biased 1.82E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 4.03E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 4.02E E E E E E E E+00 Specification MIN 3.80E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 107
108 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Output Voltage Swing RL=100 #1 (V) 3.70E E E E E E E E E E E hr hr 70 Figure Plot of Output Voltage Swing RL=100 #1 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 108
109 Table Raw data for Output Voltage Swing RL=100 #1 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=100 #1 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 3.64E E E E E E E E+00 Std Dev Biased 2.68E E E E E E E E-03 Ps90%/90% (+KTL) Biased 3.65E E E E E E E E+00 Ps90%/90% (-KTL) Biased 3.63E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 3.64E E E E E E E E+00 Std Dev Un-Biased 4.72E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 3.65E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 3.63E E E E E E E E+00 Specification MIN 3.35E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 109
110 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Output Voltage Swing RL=100 #2 (V) 3.70E E E E E E E E E E E hr hr 70 Figure Plot of Output Voltage Swing RL=100 #2 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 110
111 Table Raw data for Output Voltage Swing RL=100 #2 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=100 #2 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 3.64E E E E E E E E+00 Std Dev Biased 4.22E E E E E E E E-03 Ps90%/90% (+KTL) Biased 3.65E E E E E E E E+00 Ps90%/90% (-KTL) Biased 3.63E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 3.64E E E E E E E E+00 Std Dev Un-Biased 3.49E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 3.65E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 3.63E E E E E E E E+00 Specification MIN 3.35E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 111
112 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Output Voltage Swing RL=100 #3 (V) 3.70E E E E E E E E E E E hr hr 70 Figure Plot of Output Voltage Swing RL=100 #3 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 112
113 Table Raw data for Output Voltage Swing RL=100 #3 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=100 #3 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 3.64E E E E E E E E+00 Std Dev Biased 4.76E E E E E E E E-03 Ps90%/90% (+KTL) Biased 3.65E E E E E E E E+00 Ps90%/90% (-KTL) Biased 3.63E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 3.64E E E E E E E E+00 Std Dev Un-Biased 3.11E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 3.65E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 3.63E E E E E E E E+00 Specification MIN 3.35E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 113
114 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Output Voltage Swing RL=100 #4 (V) 3.70E E E E E E E E E E E hr hr 70 Figure Plot of Output Voltage Swing RL=100 #4 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 114
115 Table Raw data for Output Voltage Swing RL=100 #4 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=100 #4 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 3.64E E E E E E E E+00 Std Dev Biased 3.36E E E E E E E E-03 Ps90%/90% (+KTL) Biased 3.65E E E E E E E E+00 Ps90%/90% (-KTL) Biased 3.63E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 3.64E E E E E E E E+00 Std Dev Un-Biased 4.66E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 3.65E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 3.63E E E E E E E E+00 Specification MIN 3.35E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 115
116 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Output Voltage Swing RL=500 #1 (V) -3.65E E E E E E E E E hr hr 70 Figure Plot of Output Voltage Swing RL=500 #1 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 116
117 Table Raw data for Output Voltage Swing RL=500 #1 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=500 #1 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased -4.03E E E E E E E E+00 Std Dev Biased 1.30E E E E E E E E-02 Ps90%/90% (+KTL) Biased -4.02E E E E E E E E+00 Ps90%/90% (-KTL) Biased -4.03E E E E E E E E+00 Un-Biased Statistics Average Un-Biased -4.03E E E E E E E E+00 Std Dev Un-Biased 2.35E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased -4.02E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased -4.04E E E E E E E E+00 Specification MAX -3.80E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 117
118 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Output Voltage Swing RL=500 #2 (V) -3.65E E E E E E E E E hr hr 70 Figure Plot of Output Voltage Swing RL=500 #2 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 118
119 Table Raw data for Output Voltage Swing RL=500 #2 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=500 #2 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased -4.03E E E E E E E E+00 Std Dev Biased 1.64E E E E E E E E-02 Ps90%/90% (+KTL) Biased -4.02E E E E E E E E+00 Ps90%/90% (-KTL) Biased -4.03E E E E E E E E+00 Un-Biased Statistics Average Un-Biased -4.03E E E E E E E E+00 Std Dev Un-Biased 2.55E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased -4.02E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased -4.03E E E E E E E E+00 Specification MAX -3.80E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 119
120 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Output Voltage Swing RL=500 #3 (V) -3.65E E E E E E E E E hr hr 70 Figure Plot of Output Voltage Swing RL=500 #3 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 120
121 Table Raw data for Output Voltage Swing RL=500 #3 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=500 #3 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased -4.03E E E E E E E E+00 Std Dev Biased 1.52E E E E E E E E-02 Ps90%/90% (+KTL) Biased -4.02E E E E E E E E+00 Ps90%/90% (-KTL) Biased -4.03E E E E E E E E+00 Un-Biased Statistics Average Un-Biased -4.03E E E E E E E E+00 Std Dev Un-Biased 2.70E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased -4.02E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased -4.04E E E E E E E E+00 Specification MAX -3.80E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 121
122 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Output Voltage Swing RL=500 #4 (V) -3.65E E E E E E E E E hr hr 70 Figure Plot of Output Voltage Swing RL=500 #4 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 122
123 Table Raw data for Output Voltage Swing RL=500 #4 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=500 #4 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased -4.03E E E E E E E E+00 Std Dev Biased 1.10E E E E E E E E-02 Ps90%/90% (+KTL) Biased -4.02E E E E E E E E+00 Ps90%/90% (-KTL) Biased -4.03E E E E E E E E+00 Un-Biased Statistics Average Un-Biased -4.03E E E E E E E E+00 Std Dev Un-Biased 2.07E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased -4.02E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased -4.04E E E E E E E E+00 Specification MAX -3.80E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 123
124 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Output Voltage Swing RL=100 #1 (V) -3.20E E E E E E E E E E hr hr 70 Figure Plot of Output Voltage Swing RL=100 #1 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 124
125 Table Raw data for Output Voltage Swing RL=100 #1 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=100 #1 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased -3.59E E E E E E E E+00 Std Dev Biased 1.30E E E E E E E E-02 Ps90%/90% (+KTL) Biased -3.58E E E E E E E E+00 Ps90%/90% (-KTL) Biased -3.59E E E E E E E E+00 Un-Biased Statistics Average Un-Biased -3.59E E E E E E E E+00 Std Dev Un-Biased 5.50E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased -3.58E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased -3.61E E E E E E E E+00 Specification MAX -3.35E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 125
126 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Output Voltage Swing RL=100 #2 (V) -3.20E E E E E E E E E E hr hr 70 Figure Plot of Output Voltage Swing RL=100 #2 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 126
127 Table Raw data for Output Voltage Swing RL=100 #2 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=100 #2 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased -3.59E E E E E E E E+00 Std Dev Biased 2.00E E E E E E E E-02 Ps90%/90% (+KTL) Biased -3.58E E E E E E E E+00 Ps90%/90% (-KTL) Biased -3.59E E E E E E E E+00 Un-Biased Statistics Average Un-Biased -3.59E E E E E E E E+00 Std Dev Un-Biased 2.95E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased -3.58E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased -3.60E E E E E E E E+00 Specification MAX -3.35E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 127
128 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Output Voltage Swing RL=100 #3 (V) -3.20E E E E E E E E E E hr hr 70 Figure Plot of Output Voltage Swing RL=100 #3 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 128
129 Table Raw data for Output Voltage Swing RL=100 #3 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=100 #3 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased -3.59E E E E E E E E+00 Std Dev Biased 1.95E E E E E E E E-02 Ps90%/90% (+KTL) Biased -3.58E E E E E E E E+00 Ps90%/90% (-KTL) Biased -3.59E E E E E E E E+00 Un-Biased Statistics Average Un-Biased -3.59E E E E E E E E+00 Std Dev Un-Biased 2.49E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased -3.58E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased -3.60E E E E E E E E+00 Specification MAX -3.35E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 129
130 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Output Voltage Swing RL=100 #4 (V) -3.20E E E E E E E E E E hr hr 70 Figure Plot of Output Voltage Swing RL=100 #4 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 130
131 Table Raw data for Output Voltage Swing RL=100 #4 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=100 #4 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased -3.59E E E E E E E E+00 Std Dev Biased 1.14E E E E E E E E-02 Ps90%/90% (+KTL) Biased -3.59E E E E E E E E+00 Ps90%/90% (-KTL) Biased -3.59E E E E E E E E+00 Un-Biased Statistics Average Un-Biased -3.59E E E E E E E E+00 Std Dev Un-Biased 4.95E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased -3.58E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased -3.60E E E E E E E E+00 Specification MAX -3.35E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 131
132 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Maximum Output Source #1 (A) 7.00E E E E E E E E hr hr 70 Figure Plot of Maximum Output Source #1 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 132
133 Table Raw data for Maximum Output Source #1 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Maximum Output Source #1 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased 6.34E E E E E E E E-02 Std Dev Biased 4.14E E E E E E E E-04 Ps90%/90% (+KTL) Biased 6.45E E E E E E E E-02 Ps90%/90% (-KTL) Biased 6.22E E E E E E E E-02 Un-Biased Statistics Average Un-Biased 6.36E E E E E E E E-02 Std Dev Un-Biased 9.19E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 6.61E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased 6.11E E E E E E E E-02 Specification MIN 4.00E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 133
134 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Maximum Output Source #2 (A) 7.00E E E E E E E E hr hr 70 Figure Plot of Maximum Output Source #2 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 134
135 Table Raw data for Maximum Output Source #2 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Maximum Output Source #2 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased 6.34E E E E E E E E-02 Std Dev Biased 7.35E E E E E E E E-04 Ps90%/90% (+KTL) Biased 6.55E E E E E E E E-02 Ps90%/90% (-KTL) Biased 6.14E E E E E E E E-02 Un-Biased Statistics Average Un-Biased 6.31E E E E E E E E-02 Std Dev Un-Biased 4.90E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 6.44E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased 6.17E E E E E E E E-02 Specification MIN 4.00E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 135
136 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Maximum Output Source #3 (A) 7.00E E E E E E E E hr hr 70 Figure Plot of Maximum Output Source #3 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 136
137 Table Raw data for Maximum Output Source #3 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Maximum Output Source #3 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased 6.34E E E E E E E E-02 Std Dev Biased 7.82E E E E E E E E-04 Ps90%/90% (+KTL) Biased 6.56E E E E E E E E-02 Ps90%/90% (-KTL) Biased 6.13E E E E E E E E-02 Un-Biased Statistics Average Un-Biased 6.30E E E E E E E E-02 Std Dev Un-Biased 4.80E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 6.44E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased 6.17E E E E E E E E-02 Specification MIN 4.00E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 137
138 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Maximum Output Source #4 (A) 7.00E E E E E E E E hr hr 70 Figure Plot of Maximum Output Source #4 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 138
139 Table Raw data for Maximum Output Source #4 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Maximum Output Source #4 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased 6.33E E E E E E E E-02 Std Dev Biased 4.94E E E E E E E E-04 Ps90%/90% (+KTL) Biased 6.47E E E E E E E E-02 Ps90%/90% (-KTL) Biased 6.20E E E E E E E E-02 Un-Biased Statistics Average Un-Biased 6.34E E E E E E E E-02 Std Dev Un-Biased 8.42E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 6.58E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased 6.11E E E E E E E E-02 Specification MIN 4.00E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 139
140 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Maximum Output Sink #1 (A) 0.00E E E E E E E hr hr 70 Figure Plot of Maximum Output Sink #1 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 140
141 Table Raw data for Maximum Output Sink #1 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Maximum Output Sink #1 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased -5.67E E E E E E E E-02 Std Dev Biased 3.28E E E E E E E E-03 Ps90%/90% (+KTL) Biased -5.58E E E E E E E E-02 Ps90%/90% (-KTL) Biased -5.76E E E E E E E E-02 Un-Biased Statistics Average Un-Biased -5.70E E E E E E E E-02 Std Dev Un-Biased 1.33E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased -5.33E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased -6.06E E E E E E E E-02 Specification MAX -4.00E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 141
142 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Maximum Output Sink #2 (A) 0.00E E E E E E E hr hr 70 Figure Plot of Maximum Output Sink #2 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 142
143 Table Raw data for Maximum Output Sink #2 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Maximum Output Sink #2 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased -5.68E E E E E E E E-02 Std Dev Biased 5.47E E E E E E E E-03 Ps90%/90% (+KTL) Biased -5.53E E E E E E E E-02 Ps90%/90% (-KTL) Biased -5.83E E E E E E E E-02 Un-Biased Statistics Average Un-Biased -5.66E E E E E E E E-02 Std Dev Un-Biased 7.50E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased -5.45E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased -5.86E E E E E E E E-02 Specification MAX -4.00E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 143
144 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Maximum Output Sink #3 (A) 0.00E E E E E E E hr hr 70 Figure Plot of Maximum Output Sink #3 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 144
145 Table Raw data for Maximum Output Sink #3 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Maximum Output Sink #3 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased -5.69E E E E E E E E-02 Std Dev Biased 6.15E E E E E E E E-03 Ps90%/90% (+KTL) Biased -5.52E E E E E E E E-02 Ps90%/90% (-KTL) Biased -5.86E E E E E E E E-02 Un-Biased Statistics Average Un-Biased -5.66E E E E E E E E-02 Std Dev Un-Biased 5.16E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased -5.52E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased -5.80E E E E E E E E-02 Specification MAX -4.00E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 145
146 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Maximum Output Sink #4 (A) 0.00E E E E E E E hr hr 70 Figure Plot of Maximum Output Sink #4 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 146
147 Table Raw data for Maximum Output Sink #4 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Maximum Output Sink #4 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased -5.68E E E E E E E E-02 Std Dev Biased 3.42E E E E E E E E-03 Ps90%/90% (+KTL) Biased -5.58E E E E E E E E-02 Ps90%/90% (-KTL) Biased -5.77E E E E E E E E-02 Un-Biased Statistics Average Un-Biased -5.68E E E E E E E E-02 Std Dev Un-Biased 1.17E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased -5.36E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased -6.01E E E E E E E E-02 Specification MAX -4.00E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 147
148 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Positive Short-Circuit #1 (A) 9.00E E E E E E E E E hr hr 70 Figure Plot of Positive Short-Circuit #1 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 148
149 Table Raw data for Positive Short-Circuit #1 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Short-Circuit #1 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased 8.59E E E E E E E E-02 Std Dev Biased 3.40E E E E E E E E-04 Ps90%/90% (+KTL) Biased 8.69E E E E E E E E-02 Ps90%/90% (-KTL) Biased 8.50E E E E E E E E-02 Un-Biased Statistics Average Un-Biased 8.62E E E E E E E E-02 Std Dev Un-Biased 5.81E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 8.78E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased 8.46E E E E E E E E-02 Specification MIN 7.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 149
150 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Positive Short-Circuit #2 (A) 9.00E E E E E E E E E hr hr 70 Figure Plot of Positive Short-Circuit #2 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 150
151 Table Raw data for Positive Short-Circuit #2 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Short-Circuit #2 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased 8.60E E E E E E E E-02 Std Dev Biased 4.33E E E E E E E E-04 Ps90%/90% (+KTL) Biased 8.72E E E E E E E E-02 Ps90%/90% (-KTL) Biased 8.48E E E E E E E E-02 Un-Biased Statistics Average Un-Biased 8.60E E E E E E E E-02 Std Dev Un-Biased 5.57E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 8.75E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased 8.45E E E E E E E E-02 Specification MIN 7.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 151
152 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Positive Short-Circuit #3 (A) 8.80E E E E E E E E hr hr 70 Figure Plot of Positive Short-Circuit #3 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 152
153 Table Raw data for Positive Short-Circuit #3 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Short-Circuit #3 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased 8.59E E E E E E E E-02 Std Dev Biased 4.44E E E E E E E E-04 Ps90%/90% (+KTL) Biased 8.71E E E E E E E E-02 Ps90%/90% (-KTL) Biased 8.47E E E E E E E E-02 Un-Biased Statistics Average Un-Biased 8.59E E E E E E E E-02 Std Dev Un-Biased 6.25E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 8.76E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased 8.42E E E E E E E E-02 Specification MIN 7.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 153
154 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Positive Short-Circuit #4 (A) 8.80E E E E E E E E hr hr 70 Figure Plot of Positive Short-Circuit #4 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 154
155 Table Raw data for Positive Short-Circuit #4 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Short-Circuit #4 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased 8.59E E E E E E E E-02 Std Dev Biased 4.04E E E E E E E E-04 Ps90%/90% (+KTL) Biased 8.70E E E E E E E E-02 Ps90%/90% (-KTL) Biased 8.48E E E E E E E E-02 Un-Biased Statistics Average Un-Biased 8.61E E E E E E E E-02 Std Dev Un-Biased 5.72E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 8.77E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased 8.45E E E E E E E E-02 Specification MIN 7.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 155
156 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Negative Short-Circuit #1 (A) -7.40E E E E E E E E E E E hr hr 70 Figure Plot of Negative Short-Circuit #1 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 156
157 Table Raw data for Negative Short-Circuit #1 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Short-Circuit #1 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased -8.16E E E E E E E E-02 Std Dev Biased 3.56E E E E E E E E-04 Ps90%/90% (+KTL) Biased -8.06E E E E E E E E-02 Ps90%/90% (-KTL) Biased -8.25E E E E E E E E-02 Un-Biased Statistics Average Un-Biased -8.18E E E E E E E E-02 Std Dev Un-Biased 5.94E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased -8.02E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased -8.34E E E E E E E E-02 Specification MAX -7.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 157
158 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Negative Short-Circuit #2 (A) -7.40E E E E E E E E E E E hr hr 70 Figure Plot of Negative Short-Circuit #2 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 158
159 Table Raw data for Negative Short-Circuit #2 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Short-Circuit #2 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased -8.16E E E E E E E E-02 Std Dev Biased 4.83E E E E E E E E-04 Ps90%/90% (+KTL) Biased -8.03E E E E E E E E-02 Ps90%/90% (-KTL) Biased -8.30E E E E E E E E-02 Un-Biased Statistics Average Un-Biased -8.17E E E E E E E E-02 Std Dev Un-Biased 6.02E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased -8.01E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased -8.34E E E E E E E E-02 Specification MAX -7.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 159
160 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Negative Short-Circuit #3 (A) -7.40E E E E E E E E E E E hr hr 70 Figure Plot of Negative Short-Circuit #3 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 160
161 Table Raw data for Negative Short-Circuit #3 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Short-Circuit #3 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased -8.15E E E E E E E E-02 Std Dev Biased 4.11E E E E E E E E-04 Ps90%/90% (+KTL) Biased -8.04E E E E E E E E-02 Ps90%/90% (-KTL) Biased -8.27E E E E E E E E-02 Un-Biased Statistics Average Un-Biased -8.16E E E E E E E E-02 Std Dev Un-Biased 6.03E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased -7.99E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased -8.33E E E E E E E E-02 Specification MAX -7.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 161
162 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX Negative Short-Circuit #4 (A) -7.40E E E E E E E E E E E hr hr 70 Figure Plot of Negative Short-Circuit #4 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 162
163 Table Raw data for Negative Short-Circuit #4 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Short-Circuit #4 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased -8.16E E E E E E E E-02 Std Dev Biased 3.60E E E E E E E E-04 Ps90%/90% (+KTL) Biased -8.06E E E E E E E E-02 Ps90%/90% (-KTL) Biased -8.26E E E E E E E E-02 Un-Biased Statistics Average Un-Biased -8.18E E E E E E E E-02 Std Dev Un-Biased 5.69E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased -8.02E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased -8.33E E E E E E E E-02 Specification MAX -7.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 163
164 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX 1.80E-02 Positive Supply (A) 1.60E E E E E E E E E hr hr 70 Figure Plot of Positive Supply (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 164
165 Table Raw data for Positive Supply (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Supply (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased 1.45E E E E E E E E-02 Std Dev Biased 2.51E E E E E E E E-04 Ps90%/90% (+KTL) Biased 1.52E E E E E E E E-02 Ps90%/90% (-KTL) Biased 1.38E E E E E E E E-02 Un-Biased Statistics Average Un-Biased 1.41E E E E E E E E-02 Std Dev Un-Biased 9.48E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 1.67E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased 1.15E E E E E E E E-02 Specification MAX 1.60E E E E E E E E-02 Status PASS PASS PASS N/A N/A PASS PASS PASS 165
166 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 0.00E+00 Negative Supply (A) -2.00E E E E E E E E E hr hr 70 Figure Plot of Negative Supply (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 166
167 Table Raw data for Negative Supply (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Supply (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased -1.45E E E E E E E E-02 Std Dev Biased 2.45E E E E E E E E-04 Ps90%/90% (+KTL) Biased -1.38E E E E E E E E-02 Ps90%/90% (-KTL) Biased -1.51E E E E E E E E-02 Un-Biased Statistics Average Un-Biased -1.40E E E E E E E E-02 Std Dev Un-Biased 9.41E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased -1.14E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased -1.66E E E E E E E E-02 Specification MIN -1.60E E E E E E E E-02 Status PASS PASS PASS N/A N/A PASS PASS PASS 167
168 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 5.00E-03 Input Offset #1 (V) 4.00E E E E E E E E E E hr hr 70 Figure Plot of Input Offset #1 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 168
169 Table Raw data for Input Offset #1 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset #1 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-05 Biased Statistics Average Biased -2.51E E E E E E E E-04 Std Dev Biased 3.84E E E E E E E E-04 Ps90%/90% (+KTL) Biased 8.01E E E E E E E E-04 Ps90%/90% (-KTL) Biased -1.30E E E E E E E E-03 Un-Biased Statistics Average Un-Biased -1.29E E E E E E E E-04 Std Dev Un-Biased 5.55E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 1.39E E E E E E E E-03 Ps90%/90% (-KTL) Un-Biased -1.65E E E E E E E E-03 Specification MIN -2.00E E E E E E E E-03 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 2.00E E E E E E E E-03 Status PASS PASS PASS N/A N/A PASS PASS PASS 169
170 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 5.00E-03 Input Offset #2 (V) 4.00E E E E E E E E E E hr hr 70 Figure Plot of Input Offset #2 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 170
171 Table Raw data for Input Offset #2 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset #2 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-04 Biased Statistics Average Biased -3.25E E E E E E E E-04 Std Dev Biased 4.04E E E E E E E E-04 Ps90%/90% (+KTL) Biased 7.82E E E E E E E E-04 Ps90%/90% (-KTL) Biased -1.43E E E E E E E E-03 Un-Biased Statistics Average Un-Biased -2.16E E E E E E E E-04 Std Dev Un-Biased 2.76E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 5.41E E E E E E E E-04 Ps90%/90% (-KTL) Un-Biased -9.73E E E E E E E E-03 Specification MIN -2.00E E E E E E E E-03 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 2.00E E E E E E E E-03 Status PASS PASS PASS N/A N/A PASS PASS PASS 171
172 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 5.00E-03 Input Offset #3 (V) 4.00E E E E E E E E E E hr hr 70 Figure Plot of Input Offset #3 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 172
173 Table Raw data for Input Offset #3 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset #3 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-04 Biased Statistics Average Biased -2.62E E E E E E E E-04 Std Dev Biased 6.09E E E E E E E E-04 Ps90%/90% (+KTL) Biased 1.41E E E E E E E E-03 Ps90%/90% (-KTL) Biased -1.93E E E E E E E E-03 Un-Biased Statistics Average Un-Biased -2.82E E E E E E E E-04 Std Dev Un-Biased 3.59E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 7.02E E E E E E E E-04 Ps90%/90% (-KTL) Un-Biased -1.27E E E E E E E E-03 Specification MIN -2.00E E E E E E E E-03 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 2.00E E E E E E E E-03 Status PASS PASS PASS N/A N/A PASS PASS PASS 173
174 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 5.00E-03 Input Offset #4 (V) 4.00E E E E E E E E E E hr hr 70 Figure Plot of Input Offset #4 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 174
175 Table Raw data for Input Offset #4 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset #4 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-05 Biased Statistics Average Biased -1.54E E E E E E E E-04 Std Dev Biased 2.09E E E E E E E E-04 Ps90%/90% (+KTL) Biased 4.20E E E E E E E E-04 Ps90%/90% (-KTL) Biased -7.28E E E E E E E E-04 Un-Biased Statistics Average Un-Biased 1.79E E E E E E E E-04 Std Dev Un-Biased 2.40E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 8.37E E E E E E E E-04 Ps90%/90% (-KTL) Un-Biased -4.79E E E E E E E E-04 Specification MIN -2.00E E E E E E E E-03 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 2.00E E E E E E E E-03 Status PASS PASS PASS N/A N/A PASS PASS PASS 175
176 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 1.00E-06 Input Offset #1 (A) 8.00E E E E E E E E E E hr hr 70 Figure Plot of Input Offset #1 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 176
177 Table Raw data for Input Offset #1 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset #1 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-08 Biased Statistics Average Biased 2.53E E E E E E E E-09 Std Dev Biased 6.99E E E E E E E E-09 Ps90%/90% (+KTL) Biased 2.17E E E E E E E E-08 Ps90%/90% (-KTL) Biased -1.66E E E E E E E E-08 Un-Biased Statistics Average Un-Biased 1.72E E E E E E E E-09 Std Dev Un-Biased 8.09E E E E E E E E-09 Ps90%/90% (+KTL) Un-Biased 2.39E E E E E E E E-08 Ps90%/90% (-KTL) Un-Biased -2.05E E E E E E E E-08 Specification MIN -4.00E E E E E E E E-07 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-07 Status PASS PASS PASS N/A N/A PASS PASS PASS 177
178 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 1.00E-06 Input Offset #2 (A) 8.00E E E E E E E E E E hr hr 70 Figure Plot of Input Offset #2 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 178
179 Table Raw data for Input Offset #2 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset #2 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 3.38E E E E E E E E-09 Std Dev Biased 1.34E E E E E E E E-08 Ps90%/90% (+KTL) Biased 4.00E E E E E E E E-08 Ps90%/90% (-KTL) Biased -3.33E E E E E E E E-08 Un-Biased Statistics Average Un-Biased 1.50E E E E E E E E+00 Std Dev Un-Biased 5.04E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.53E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased -1.23E E E E E E E E+00 Specification MIN -4.00E E E E E E E E-07 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-07 Status PASS PASS PASS N/A N/A PASS PASS PASS 179
180 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 1.00E-06 Input Offset #3 (A) 8.00E E E E E E E E E E hr hr 70 Figure Plot of Input Offset #3 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 180
181 Table Raw data for Input Offset #3 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset #3 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-08 Biased Statistics Average Biased 2.08E E E E E E E E+00 Std Dev Biased 3.16E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.07E E E E E E E E+00 Ps90%/90% (-KTL) Biased -6.58E E E E E E E E+00 Un-Biased Statistics Average Un-Biased -1.78E E E E E E E E+00 Std Dev Un-Biased 5.19E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.40E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased -1.44E E E E E E E E+00 Specification MIN -4.00E E E E E E E E-07 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-07 Status PASS PASS PASS N/A N/A PASS PASS PASS 181
182 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX 1.00E-06 Input Offset #4 (A) 8.00E E E E E E E E E E hr hr 70 Figure Plot of Input Offset #4 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 182
183 Table Raw data for Input Offset #4 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Input Offset #4 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 5.26E E E E E E E E-09 Std Dev Biased 1.40E E E E E E E E-08 Ps90%/90% (+KTL) Biased 4.37E E E E E E E E-08 Ps90%/90% (-KTL) Biased -3.31E E E E E E E E-08 Un-Biased Statistics Average Un-Biased 1.14E E E E E E E E-08 Std Dev Un-Biased 1.39E E E E E E E E-08 Ps90%/90% (+KTL) Un-Biased 4.96E E E E E E E E-08 Ps90%/90% (-KTL) Un-Biased -2.68E E E E E E E E-08 Specification MIN -4.00E E E E E E E E-07 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-07 Status PASS PASS PASS N/A N/A PASS PASS PASS 183
184 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Positive Input Bias #1 (A) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Positive Input Bias #1 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 184
185 Table Raw data for Positive Input Bias #1 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Input Bias #1 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-07 Biased Statistics Average Biased 2.64E E E E E E E E-07 Std Dev Biased 1.14E E E E E E E E-08 Ps90%/90% (+KTL) Biased 2.95E E E E E E E E-07 Ps90%/90% (-KTL) Biased 2.33E E E E E E E E-07 Un-Biased Statistics Average Un-Biased 2.50E E E E E E E E-07 Std Dev Un-Biased 2.00E E E E E E E E-08 Ps90%/90% (+KTL) Un-Biased 3.05E E E E E E E E-07 Ps90%/90% (-KTL) Un-Biased 1.95E E E E E E E E-07 Specification MIN -4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS 185
186 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Positive Input Bias #2 (A) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Positive Input Bias #2 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 186
187 Table Raw data for Positive Input Bias #2 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Input Bias #2 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-07 Biased Statistics Average Biased 2.58E E E E E E E E-07 Std Dev Biased 1.79E E E E E E E E-08 Ps90%/90% (+KTL) Biased 3.07E E E E E E E E-07 Ps90%/90% (-KTL) Biased 2.09E E E E E E E E-07 Un-Biased Statistics Average Un-Biased 2.50E E E E E E E E-07 Std Dev Un-Biased 1.87E E E E E E E E-08 Ps90%/90% (+KTL) Un-Biased 3.01E E E E E E E E-07 Ps90%/90% (-KTL) Un-Biased 1.99E E E E E E E E-07 Specification MIN -4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS 187
188 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Positive Input Bias #3 (A) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Positive Input Bias #3 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 188
189 Table Raw data for Positive Input Bias #3 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Input Bias #3 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-07 Biased Statistics Average Biased 2.62E E E E E E E E-07 Std Dev Biased 2.49E E E E E E E E-08 Ps90%/90% (+KTL) Biased 3.30E E E E E E E E-07 Ps90%/90% (-KTL) Biased 1.94E E E E E E E E-07 Un-Biased Statistics Average Un-Biased 2.54E E E E E E E E-07 Std Dev Un-Biased 1.67E E E E E E E E-08 Ps90%/90% (+KTL) Un-Biased 3.00E E E E E E E E-07 Ps90%/90% (-KTL) Un-Biased 2.08E E E E E E E E-07 Specification MIN -4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS 189
190 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Positive Input Bias #4 (A) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Positive Input Bias #4 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 190
191 Table Raw data for Positive Input Bias #4 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Input Bias #4 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-07 Biased Statistics Average Biased 2.70E E E E E E E E-07 Std Dev Biased 1.22E E E E E E E E-08 Ps90%/90% (+KTL) Biased 3.04E E E E E E E E-07 Ps90%/90% (-KTL) Biased 2.36E E E E E E E E-07 Un-Biased Statistics Average Un-Biased 2.52E E E E E E E E-07 Std Dev Un-Biased 1.79E E E E E E E E-08 Ps90%/90% (+KTL) Un-Biased 3.01E E E E E E E E-07 Ps90%/90% (-KTL) Un-Biased 2.03E E E E E E E E-07 Specification MIN -4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS 191
192 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Negative Input Bias #1 (A) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Negative Input Bias #1 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 192
193 Table Raw data for Negative Input Bias #1 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Input Bias #1 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-07 Biased Statistics Average Biased 2.64E E E E E E E E-07 Std Dev Biased 1.52E E E E E E E E-08 Ps90%/90% (+KTL) Biased 3.06E E E E E E E E-07 Ps90%/90% (-KTL) Biased 2.22E E E E E E E E-07 Un-Biased Statistics Average Un-Biased 2.44E E E E E E E E-07 Std Dev Un-Biased 1.95E E E E E E E E-08 Ps90%/90% (+KTL) Un-Biased 2.97E E E E E E E E-07 Ps90%/90% (-KTL) Un-Biased 1.91E E E E E E E E-07 Specification MIN -4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS 193
194 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Negative Input Bias #2 (A) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Negative Input Bias #2 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 194
195 Table Raw data for Negative Input Bias #2 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Input Bias #2 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-07 Biased Statistics Average Biased 2.56E E E E E E E E-07 Std Dev Biased 1.82E E E E E E E E-08 Ps90%/90% (+KTL) Biased 3.06E E E E E E E E-07 Ps90%/90% (-KTL) Biased 2.06E E E E E E E E-07 Un-Biased Statistics Average Un-Biased 2.46E E E E E E E E-07 Std Dev Un-Biased 2.51E E E E E E E E-08 Ps90%/90% (+KTL) Un-Biased 3.15E E E E E E E E-07 Ps90%/90% (-KTL) Un-Biased 1.77E E E E E E E E-07 Specification MIN -4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS 195
196 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Negative Input Bias #3 (A) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Negative Input Bias #3 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 196
197 Table Raw data for Negative Input Bias #3 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Input Bias #3 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-07 Biased Statistics Average Biased 2.62E E E E E E E E-07 Std Dev Biased 2.49E E E E E E E E-08 Ps90%/90% (+KTL) Biased 3.30E E E E E E E E-07 Ps90%/90% (-KTL) Biased 1.94E E E E E E E E-07 Un-Biased Statistics Average Un-Biased 2.58E E E E E E E E-07 Std Dev Un-Biased 1.92E E E E E E E E-08 Ps90%/90% (+KTL) Un-Biased 3.11E E E E E E E E-07 Ps90%/90% (-KTL) Un-Biased 2.05E E E E E E E E-07 Specification MIN -4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS 197
198 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MIN Specification MAX Negative Input Bias #4 (A) 1.00E E E E E E E E E E E hr hr 70 Figure Plot of Negative Input Bias #4 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 198
199 Table Raw data for Negative Input Bias #4 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Input Bias #4 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-07 Biased Statistics Average Biased 2.66E E E E E E E E-07 Std Dev Biased 8.94E E E E E E E E-08 Ps90%/90% (+KTL) Biased 2.91E E E E E E E E-07 Ps90%/90% (-KTL) Biased 2.41E E E E E E E E-07 Un-Biased Statistics Average Un-Biased 2.38E E E E E E E E-07 Std Dev Un-Biased 1.79E E E E E E E E-08 Ps90%/90% (+KTL) Un-Biased 2.87E E E E E E E E-07 Ps90%/90% (-KTL) Un-Biased 1.89E E E E E E E E-07 Specification MIN -4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS Specification MAX 4.00E E E E E E E E-06 Status PASS PASS PASS N/A N/A PASS PASS PASS 199
200 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Common Mode Rejection #1 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Common Mode Rejection #1 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 200
201 Table Raw data for Common Mode Rejection #1 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Common Mode Rejection #1 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+01 Biased Statistics Average Biased 9.67E E E E E E E E+01 Std Dev Biased 7.30E E E E E E E E+00 Ps90%/90% (+KTL) Biased 9.87E E E E E E E E+02 Ps90%/90% (-KTL) Biased 9.47E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 9.68E E E E E E E E+01 Std Dev Un-Biased 7.51E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 9.88E E E E E E E E+01 Ps90%/90% (-KTL) Un-Biased 9.47E E E E E E E E+01 Specification MIN 7.30E E E E E E E E+01 Status PASS PASS PASS N/A N/A PASS PASS PASS 201
202 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Common Mode Rejection #2 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Common Mode Rejection #2 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 202
203 Table Raw data for Common Mode Rejection #2 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Common Mode Rejection #2 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+01 Biased Statistics Average Biased 9.65E E E E E E E E+01 Std Dev Biased 1.31E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.00E E E E E E E E+02 Ps90%/90% (-KTL) Biased 9.29E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 9.71E E E E E E E E+01 Std Dev Un-Biased 7.21E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 9.91E E E E E E E E+01 Ps90%/90% (-KTL) Un-Biased 9.51E E E E E E E E+01 Specification MIN 7.30E E E E E E E E+01 Status PASS PASS PASS N/A N/A PASS PASS PASS 203
204 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Common Mode Rejection #3 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Common Mode Rejection #3 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 204
205 Table Raw data for Common Mode Rejection #3 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Common Mode Rejection #3 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+01 Biased Statistics Average Biased 9.70E E E E E E E E+01 Std Dev Biased 9.86E E E E E E E E+00 Ps90%/90% (+KTL) Biased 9.97E E E E E E E E+02 Ps90%/90% (-KTL) Biased 9.43E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 9.71E E E E E E E E+01 Std Dev Un-Biased 1.16E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.00E E E E E E E E+01 Ps90%/90% (-KTL) Un-Biased 9.39E E E E E E E E+01 Specification MIN 7.30E E E E E E E E+01 Status PASS PASS PASS N/A N/A PASS PASS PASS 205
206 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Common Mode Rejection #4 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Common Mode Rejection #4 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 206
207 Table Raw data for Common Mode Rejection #4 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Common Mode Rejection #4 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+01 Biased Statistics Average Biased 9.65E E E E E E E E+01 Std Dev Biased 1.35E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.00E E E E E E E E+02 Ps90%/90% (-KTL) Biased 9.28E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 9.76E E E E E E E E+01 Std Dev Un-Biased 8.77E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 1.00E E E E E E E E+01 Ps90%/90% (-KTL) Un-Biased 9.52E E E E E E E E+01 Specification MIN 7.30E E E E E E E E+01 Status PASS PASS PASS N/A N/A PASS PASS PASS 207
208 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Large Signal Voltage RL=500 #1 (V/mV) 3.50E E E E E E E E hr hr 70 Figure Plot of Large Signal Voltage RL=500 #1 (V/mV) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 208
209 Table Raw data for Large Signal Voltage RL=500 #1 (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Large Signal Voltage RL=500 #1 (V/mV) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 2.99E E E E E E E E+00 Std Dev Biased 4.79E E E E E E E E-01 Ps90%/90% (+KTL) Biased 3.12E E E E E E E E+00 Ps90%/90% (-KTL) Biased 2.86E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 3.11E E E E E E E E+00 Std Dev Un-Biased 2.10E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 3.69E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 2.54E E E E E E E E+00 Specification MIN 1.00E E E E E E E E-01 Status PASS PASS PASS N/A N/A PASS PASS PASS 209
210 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Large Signal Voltage RL=500 #2 (V/mV) 3.50E E E E E E E E hr hr 70 Figure Plot of Large Signal Voltage RL=500 #2 (V/mV) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 210
211 Table Raw data for Large Signal Voltage RL=500 #2 (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Large Signal Voltage RL=500 #2 (V/mV) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 2.99E E E E E E E E+00 Std Dev Biased 4.99E E E E E E E E-01 Ps90%/90% (+KTL) Biased 3.13E E E E E E E E+00 Ps90%/90% (-KTL) Biased 2.85E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 3.05E E E E E E E E+00 Std Dev Un-Biased 1.50E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 3.46E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 2.64E E E E E E E E+00 Specification MIN 1.00E E E E E E E E-01 Status PASS PASS PASS N/A N/A PASS PASS PASS 211
212 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Large Signal Voltage RL=500 #3 (V/mV) 3.50E E E E E E E E hr hr 70 Figure Plot of Large Signal Voltage RL=500 #3 (V/mV) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 212
213 Table Raw data for Large Signal Voltage RL=500 #3 (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Large Signal Voltage RL=500 #3 (V/mV) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 3.01E E E E E E E E+00 Std Dev Biased 7.23E E E E E E E E-01 Ps90%/90% (+KTL) Biased 3.21E E E E E E E E+00 Ps90%/90% (-KTL) Biased 2.82E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 3.10E E E E E E E E+00 Std Dev Un-Biased 1.69E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 3.56E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 2.64E E E E E E E E+00 Specification MIN 1.00E E E E E E E E-01 Status PASS PASS PASS N/A N/A PASS PASS PASS 213
214 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Large Signal Voltage RL=500 #4 (V/mV) 3.50E E E E E E E E hr hr 70 Figure Plot of Large Signal Voltage RL=500 #4 (V/mV) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 214
215 Table Raw data for Large Signal Voltage RL=500 #4 (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Large Signal Voltage RL=500 #4 (V/mV) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 2.96E E E E E E E E+00 Std Dev Biased 5.96E E E E E E E E-01 Ps90%/90% (+KTL) Biased 3.12E E E E E E E E+00 Ps90%/90% (-KTL) Biased 2.80E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 3.08E E E E E E E E+00 Std Dev Un-Biased 1.84E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 3.58E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 2.57E E E E E E E E+00 Specification MIN 1.00E E E E E E E E-01 Status PASS PASS PASS N/A N/A PASS PASS PASS 215
216 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Large Signal Voltage RL=100 #1 (V/mV) 3.00E E E E E E E hr hr 70 Figure Plot of Large Signal Voltage RL=100 #1 (V/mV) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 216
217 Table Raw data for Large Signal Voltage RL=100 #1 (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Large Signal Voltage RL=100 #1 (V/mV) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 2.47E E E E E E E E+00 Std Dev Biased 4.75E E E E E E E E-01 Ps90%/90% (+KTL) Biased 2.60E E E E E E E E+00 Ps90%/90% (-KTL) Biased 2.34E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 2.57E E E E E E E E+00 Std Dev Un-Biased 1.59E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 3.01E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 2.13E E E E E E E E+00 Specification MIN 7.00E E E E E E E E-01 Status PASS PASS PASS N/A N/A PASS PASS PASS 217
218 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Large Signal Voltage RL=100 #2 (V/mV) 3.00E E E E E E E hr hr 70 Figure Plot of Large Signal Voltage RL=100 #2 (V/mV) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 218
219 Table Raw data for Large Signal Voltage RL=100 #2 (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Large Signal Voltage RL=100 #2 (V/mV) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 2.46E E E E E E E E+00 Std Dev Biased 5.00E E E E E E E E-01 Ps90%/90% (+KTL) Biased 2.60E E E E E E E E+00 Ps90%/90% (-KTL) Biased 2.32E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 2.52E E E E E E E E+00 Std Dev Un-Biased 1.15E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 2.84E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 2.20E E E E E E E E+00 Specification MIN 7.00E E E E E E E E-01 Status PASS PASS PASS N/A N/A PASS PASS PASS 219
220 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Large Signal Voltage RL=100 #3 (V/mV) 3.00E E E E E E E hr hr 70 Figure Plot of Large Signal Voltage RL=100 #3 (V/mV) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 220
221 Table Raw data for Large Signal Voltage RL=100 #3 (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Large Signal Voltage RL=100 #3 (V/mV) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 2.49E E E E E E E E+00 Std Dev Biased 7.34E E E E E E E E-01 Ps90%/90% (+KTL) Biased 2.69E E E E E E E E+00 Ps90%/90% (-KTL) Biased 2.28E E E E E E E E-01 Un-Biased Statistics Average Un-Biased 2.56E E E E E E E E+00 Std Dev Un-Biased 1.32E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 2.93E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 2.20E E E E E E E E+00 Specification MIN 7.00E E E E E E E E-01 Status PASS PASS PASS N/A N/A PASS PASS PASS 221
222 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN Large Signal Voltage RL=100 #4 (V/mV) 3.00E E E E E E E hr hr 70 Figure Plot of Large Signal Voltage RL=100 #4 (V/mV) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 222
223 Table Raw data for Large Signal Voltage RL=100 #4 (V/mV) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Large Signal Voltage RL=100 #4 (V/mV) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 2.45E E E E E E E E+00 Std Dev Biased 6.33E E E E E E E E-01 Ps90%/90% (+KTL) Biased 2.62E E E E E E E E+00 Ps90%/90% (-KTL) Biased 2.27E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 2.53E E E E E E E E+00 Std Dev Un-Biased 1.38E E E E E E E E-01 Ps90%/90% (+KTL) Un-Biased 2.91E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 2.16E E E E E E E E+00 Specification MIN 7.00E E E E E E E E-01 Status PASS PASS PASS N/A N/A PASS PASS PASS 223
224 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN 1.20E+02 Channel 1:2 (db) 1.00E E E E E E hr hr 70 Figure Plot of Channel 1:2 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 224
225 Table Raw data for Channel 1:2 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 1:2 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.05E E E E E E E E+02 Std Dev Biased 4.90E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.18E E E E E E E E+02 Ps90%/90% (-KTL) Biased 9.12E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.11E E E E E E E E+02 Std Dev Un-Biased 4.20E E E E E E E E+01 Ps90%/90% (+KTL) Un-Biased 1.22E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 9.91E E E E E E E E+01 Specification MIN 8.10E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 225
226 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 1.40E+02 Ps90%/90% (-KTL) Un-Biased Specification MIN Channel 1:3 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 1:3 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 226
227 Table Raw data for Channel 1:3 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 1:3 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+01 Biased Statistics Average Biased 1.11E E E E E E E E+02 Std Dev Biased 1.03E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.39E E E E E E E E+02 Ps90%/90% (-KTL) Biased 8.24E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.09E E E E E E E E+02 Std Dev Un-Biased 9.63E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.36E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 8.30E E E E E E E E+01 Specification MIN 8.10E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 227
228 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 1.40E+02 Ps90%/90% (-KTL) Un-Biased Specification MIN Channel 1:4 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 1:4 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 228
229 Table Raw data for Channel 1:4 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 1:4 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.07E E E E E E E E+02 Std Dev Biased 1.09E E E E E E E E+01 Ps90%/90% (+KTL) Biased 1.37E E E E E E E E+02 Ps90%/90% (-KTL) Biased 7.75E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.02E E E E E E E E+02 Std Dev Un-Biased 4.91E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.16E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 8.87E E E E E E E E+01 Specification MIN 8.10E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 229
230 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 1.40E+02 Ps90%/90% (-KTL) Un-Biased Specification MIN Channel 2:1 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 2:1 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 230
231 Table Raw data for Channel 2:1 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 2:1 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.09E E E E E E E E+02 Std Dev Biased 6.59E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.27E E E E E E E E+02 Ps90%/90% (-KTL) Biased 9.09E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.05E E E E E E E E+02 Std Dev Un-Biased 5.75E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.21E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 8.94E E E E E E E E+01 Specification MIN 8.10E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 231
232 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 1.40E+02 Ps90%/90% (-KTL) Un-Biased Specification MIN Channel 2:3 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 2:3 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 232
233 Table Raw data for Channel 2:3 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 2:3 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+01 Biased Statistics Average Biased 1.13E E E E E E E E+02 Std Dev Biased 1.10E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.43E E E E E E E E+02 Ps90%/90% (-KTL) Biased 8.33E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.03E E E E E E E E+02 Std Dev Un-Biased 7.01E E E E E E E E+01 Ps90%/90% (+KTL) Un-Biased 1.22E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 8.35E E E E E E E E+01 Specification MIN 8.10E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 233
234 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 1.40E+02 Ps90%/90% (-KTL) Un-Biased Specification MIN Channel 2:4 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 2:4 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 234
235 Table Raw data for Channel 2:4 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 2:4 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.09E E E E E E E E+02 Std Dev Biased 8.87E E E E E E E E+01 Ps90%/90% (+KTL) Biased 1.33E E E E E E E E+02 Ps90%/90% (-KTL) Biased 8.42E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.10E E E E E E E E+02 Std Dev Un-Biased 7.16E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.29E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 9.00E E E E E E E E+01 Specification MIN 8.10E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 235
236 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 1.40E+02 Ps90%/90% (-KTL) Un-Biased Specification MIN Channel 3:1 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 3:1 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 236
237 Table Raw data for Channel 3:1 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 3:1 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.09E E E E E E E E+02 Std Dev Biased 5.33E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.24E E E E E E E E+02 Ps90%/90% (-KTL) Biased 9.47E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.12E E E E E E E E+02 Std Dev Un-Biased 1.76E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.60E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 6.40E E E E E E E E+01 Specification MIN 8.10E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 237
238 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 1.40E+02 Ps90%/90% (-KTL) Un-Biased Specification MIN Channel 3:2 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 3:2 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 238
239 Table Raw data for Channel 3:2 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 3:2 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.05E E E E E E E E+02 Std Dev Biased 7.10E E E E E E E E+01 Ps90%/90% (+KTL) Biased 1.24E E E E E E E E+02 Ps90%/90% (-KTL) Biased 8.55E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.15E E E E E E E E+02 Std Dev Un-Biased 2.36E E E E E E E E+01 Ps90%/90% (+KTL) Un-Biased 1.80E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 5.02E E E E E E E E+01 Specification MIN 8.10E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 239
240 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 1.20E+02 Ps90%/90% (-KTL) Un-Biased Specification MIN Channel 3:4 (db) 1.00E E E E E E hr hr 70 Figure Plot of Channel 3:4 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 240
241 Table Raw data for Channel 3:4 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 3:4 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.12E E E E E E E E+02 Std Dev Biased 9.67E E E E E E E E+01 Ps90%/90% (+KTL) Biased 1.39E E E E E E E E+02 Ps90%/90% (-KTL) Biased 8.58E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.08E E E E E E E E+02 Std Dev Un-Biased 8.58E E E E E E E E+01 Ps90%/90% (+KTL) Un-Biased 1.32E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 8.46E E E E E E E E+01 Specification MIN 8.10E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 241
242 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 1.40E+02 Ps90%/90% (-KTL) Un-Biased Specification MIN Channel 4:1 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 4:1 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 242
243 Table Raw data for Channel 4:1 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 4:1 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.09E E E E E E E E+02 Std Dev Biased 1.10E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.40E E E E E E E E+02 Ps90%/90% (-KTL) Biased 7.92E E E E E E E E+02 Un-Biased Statistics Average Un-Biased 1.18E E E E E E E E+02 Std Dev Un-Biased 1.24E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.52E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 8.42E E E E E E E E+01 Specification MIN 8.10E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 243
244 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 1.40E+02 Ps90%/90% (-KTL) Un-Biased Specification MIN Channel 4:2 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 4:2 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 244
245 Table Raw data for Channel 4:2 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 4:2 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.00E E E E E E E E+02 Std Dev Biased 3.45E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.10E E E E E E E E+02 Ps90%/90% (-KTL) Biased 9.10E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.07E E E E E E E E+02 Std Dev Un-Biased 3.51E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.17E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 9.76E E E E E E E E+01 Specification MIN 8.10E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 245
246 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 1.40E+02 Ps90%/90% (-KTL) Un-Biased Specification MIN Channel 4:3 (db) 1.20E E E E E E E hr hr 70 Figure Plot of Channel 4:3 (db) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 246
247 Table Raw data for Channel 4:3 (db) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Channel 4:3 (db) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+02 Biased Statistics Average Biased 1.07E E E E E E E E+02 Std Dev Biased 4.64E E E E E E E E+00 Ps90%/90% (+KTL) Biased 1.20E E E E E E E E+02 Ps90%/90% (-KTL) Biased 9.41E E E E E E E E+01 Un-Biased Statistics Average Un-Biased 1.23E E E E E E E E+02 Std Dev Un-Biased 1.43E E E E E E E E+00 Ps90%/90% (+KTL) Un-Biased 1.63E E E E E E E E+02 Ps90%/90% (-KTL) Un-Biased 8.39E E E E E E E E+01 Specification MIN 8.10E E E E E E E E+01 Status PASS NA NA NA NA NA NA NA 247
248 Output Voltage Swing RL=500 #1 (V) 4.15E E E E E E E E E+00 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN hr hr 70 Figure Plot of Output Voltage Swing RL=500 #1 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 248
249 Table Raw data for Output Voltage Swing RL=500 #1 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=500 #1 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 4.11E E E E E E E E+00 Std Dev Biased 1.64E E E E E E E E-03 Ps90%/90% (+KTL) Biased 4.12E E E E E E E E+00 Ps90%/90% (-KTL) Biased 4.11E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 4.12E E E E E E E E+00 Std Dev Un-Biased 2.95E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 4.13E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 4.11E E E E E E E E+00 Specification MIN 3.90E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 249
250 Output Voltage Swing RL=500 #2 (V) 4.15E E E E E E E E E+00 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN hr hr 70 Figure Plot of Output Voltage Swing RL=500 #2 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 250
251 Table Raw data for Output Voltage Swing RL=500 #2 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=500 #2 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 4.11E E E E E E E E+00 Std Dev Biased 1.95E E E E E E E E-03 Ps90%/90% (+KTL) Biased 4.12E E E E E E E E+00 Ps90%/90% (-KTL) Biased 4.11E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 4.12E E E E E E E E+00 Std Dev Un-Biased 3.65E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 4.13E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 4.11E E E E E E E E+00 Specification MIN 3.90E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 251
252 Output Voltage Swing RL=500 #3 (V) 4.15E E E E E E E E E+00 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN hr hr 70 Figure Plot of Output Voltage Swing RL=500 #3 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 252
253 Table Raw data for Output Voltage Swing RL=500 #3 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=500 #3 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 4.11E E E E E E E E+00 Std Dev Biased 2.70E E E E E E E E-03 Ps90%/90% (+KTL) Biased 4.12E E E E E E E E+00 Ps90%/90% (-KTL) Biased 4.11E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 4.12E E E E E E E E+00 Std Dev Un-Biased 3.67E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 4.13E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 4.11E E E E E E E E+00 Specification MIN 3.90E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 253
254 Output Voltage Swing RL=500 #4 (V) 4.15E E E E E E E E E+00 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN hr hr 70 Figure Plot of Output Voltage Swing RL=500 #4 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 254
255 Table Raw data for Output Voltage Swing RL=500 #4 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=500 #4 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 4.11E E E E E E E E+00 Std Dev Biased 1.52E E E E E E E E-03 Ps90%/90% (+KTL) Biased 4.12E E E E E E E E+00 Ps90%/90% (-KTL) Biased 4.11E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 4.12E E E E E E E E+00 Std Dev Un-Biased 2.45E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 4.12E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 4.11E E E E E E E E+00 Specification MIN 3.90E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 255
256 Output Voltage Swing RL=100 #1 (V) 4.00E E E E E E E E E E E+00 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN hr hr 70 Figure Plot of Output Voltage Swing RL=100 #1 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 256
257 Table Raw data for Output Voltage Swing RL=100 #1 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=100 #1 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 3.94E E E E E E E E+00 Std Dev Biased 8.94E E E E E E E E-04 Ps90%/90% (+KTL) Biased 3.94E E E E E E E E+00 Ps90%/90% (-KTL) Biased 3.93E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 3.94E E E E E E E E+00 Std Dev Un-Biased 2.05E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 3.94E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 3.93E E E E E E E E+00 Specification MIN 3.70E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 257
258 Output Voltage Swing RL=100 #2 (V) 4.00E E E E E E E E E E E+00 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN hr hr 70 Figure Plot of Output Voltage Swing RL=100 #2 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 258
259 Table Raw data for Output Voltage Swing RL=100 #2 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=100 #2 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 3.94E E E E E E E E+00 Std Dev Biased 1.67E E E E E E E E-03 Ps90%/90% (+KTL) Biased 3.94E E E E E E E E+00 Ps90%/90% (-KTL) Biased 3.93E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 3.94E E E E E E E E+00 Std Dev Un-Biased 1.52E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 3.94E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 3.93E E E E E E E E+00 Specification MIN 3.70E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 259
260 Output Voltage Swing RL=100 #3 (V) 4.00E E E E E E E E E E E+00 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN hr hr 70 Figure Plot of Output Voltage Swing RL=100 #3 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 260
261 Table Raw data for Output Voltage Swing RL=100 #3 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=100 #3 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 3.94E E E E E E E E+00 Std Dev Biased 1.48E E E E E E E E-03 Ps90%/90% (+KTL) Biased 3.94E E E E E E E E+00 Ps90%/90% (-KTL) Biased 3.93E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 3.94E E E E E E E E+00 Std Dev Un-Biased 1.79E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 3.94E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 3.93E E E E E E E E+00 Specification MIN 3.70E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 261
262 Output Voltage Swing RL=100 #4 (V) 4.00E E E E E E E E E E E+00 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased Ps90%/90% (-KTL) Un-Biased Specification MIN hr hr 70 Figure Plot of Output Voltage Swing RL=100 #4 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 262
263 Table Raw data for Output Voltage Swing RL=100 #4 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=100 #4 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 3.94E E E E E E E E+00 Std Dev Biased 1.34E E E E E E E E-03 Ps90%/90% (+KTL) Biased 3.94E E E E E E E E+00 Ps90%/90% (-KTL) Biased 3.93E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 3.94E E E E E E E E+00 Std Dev Un-Biased 1.82E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 3.94E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 3.93E E E E E E E E+00 Specification MIN 3.70E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 263
264 Output Voltage Swing RL=500 #1 (V) 1.40E E E E E E E E+00 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX hr hr 70 Figure Plot of Output Voltage Swing RL=500 #1 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 264
265 Table Raw data for Output Voltage Swing RL=500 #1 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=500 #1 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-01 Biased Statistics Average Biased 8.92E E E E E E E E-01 Std Dev Biased 1.79E E E E E E E E-03 Ps90%/90% (+KTL) Biased 8.97E E E E E E E E-01 Ps90%/90% (-KTL) Biased 8.87E E E E E E E E-01 Un-Biased Statistics Average Un-Biased 8.87E E E E E E E E-01 Std Dev Un-Biased 2.59E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 8.94E E E E E E E E-01 Ps90%/90% (-KTL) Un-Biased 8.80E E E E E E E E-01 Specification MAX 1.10E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 265
266 Output Voltage Swing RL=500 #2 (V) 1.40E E E E E E E E+00 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX hr hr 70 Figure Plot of Output Voltage Swing RL=500 #2 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 266
267 Table Raw data for Output Voltage Swing RL=500 #2 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=500 #2 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-01 Biased Statistics Average Biased 8.92E E E E E E E E-01 Std Dev Biased 2.39E E E E E E E E-03 Ps90%/90% (+KTL) Biased 8.99E E E E E E E E-01 Ps90%/90% (-KTL) Biased 8.86E E E E E E E E-01 Un-Biased Statistics Average Un-Biased 8.90E E E E E E E E-01 Std Dev Un-Biased 3.97E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 9.00E E E E E E E E-01 Ps90%/90% (-KTL) Un-Biased 8.79E E E E E E E E-01 Specification MAX 1.10E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 267
268 Output Voltage Swing RL=500 #3 (V) 1.40E E E E E E E E+00 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX hr hr 70 Figure Plot of Output Voltage Swing RL=500 #3 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 268
269 Table Raw data for Output Voltage Swing RL=500 #3 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=500 #3 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-01 Biased Statistics Average Biased 8.92E E E E E E E E-01 Std Dev Biased 1.82E E E E E E E E-03 Ps90%/90% (+KTL) Biased 8.97E E E E E E E E-01 Ps90%/90% (-KTL) Biased 8.87E E E E E E E E-01 Un-Biased Statistics Average Un-Biased 8.89E E E E E E E E-01 Std Dev Un-Biased 4.66E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 9.02E E E E E E E E-01 Ps90%/90% (-KTL) Un-Biased 8.76E E E E E E E E-01 Specification MAX 1.10E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 269
270 Output Voltage Swing RL=500 #4 (V) 1.40E E E E E E E E+00 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX hr hr 70 Figure Plot of Output Voltage Swing RL=500 #4 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 270
271 Table Raw data for Output Voltage Swing RL=500 #4 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=500 #4 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-01 Biased Statistics Average Biased 8.93E E E E E E E E-01 Std Dev Biased 1.22E E E E E E E E-03 Ps90%/90% (+KTL) Biased 8.96E E E E E E E E-01 Ps90%/90% (-KTL) Biased 8.90E E E E E E E E-01 Un-Biased Statistics Average Un-Biased 8.87E E E E E E E E-01 Std Dev Un-Biased 2.70E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 8.95E E E E E E E E-01 Ps90%/90% (-KTL) Un-Biased 8.80E E E E E E E E-01 Specification MAX 1.10E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 271
272 Output Voltage Swing RL=100 #1 (V) 1.60E E E E E E E E E+00 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX hr hr 70 Figure Plot of Output Voltage Swing RL=100 #1 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 272
273 Table Raw data for Output Voltage Swing RL=100 #1 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=100 #1 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 1.07E E E E E E E E+00 Std Dev Biased 5.48E E E E E E E E-03 Ps90%/90% (+KTL) Biased 1.07E E E E E E E E+00 Ps90%/90% (-KTL) Biased 1.07E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 1.07E E E E E E E E+00 Std Dev Un-Biased 1.92E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 1.07E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 1.06E E E E E E E E+00 Specification MAX 1.30E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 273
274 Output Voltage Swing RL=100 #2 (V) 1.60E E E E E E E E E+00 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX hr hr 70 Figure Plot of Output Voltage Swing RL=100 #2 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 274
275 Table Raw data for Output Voltage Swing RL=100 #2 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=100 #2 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 1.07E E E E E E E E+00 Std Dev Biased 1.10E E E E E E E E-03 Ps90%/90% (+KTL) Biased 1.07E E E E E E E E+00 Ps90%/90% (-KTL) Biased 1.07E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 1.07E E E E E E E E+00 Std Dev Un-Biased 1.34E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 1.07E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 1.07E E E E E E E E+00 Specification MAX 1.30E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 275
276 Output Voltage Swing RL=100 #3 (V) 1.60E E E E E E E E E+00 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX hr hr 70 Figure Plot of Output Voltage Swing RL=100 #3 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 276
277 Table Raw data for Output Voltage Swing RL=100 #3 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=100 #3 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 1.07E E E E E E E E+00 Std Dev Biased 8.37E E E E E E E E-03 Ps90%/90% (+KTL) Biased 1.07E E E E E E E E+00 Ps90%/90% (-KTL) Biased 1.07E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 1.07E E E E E E E E+00 Std Dev Un-Biased 1.87E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 1.07E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 1.06E E E E E E E E+00 Specification MAX 1.30E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 277
278 Output Voltage Swing RL=100 #4 (V) 1.60E E E E E E E E E+00 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased Ps90%/90% (+KTL) Un-Biased Specification MAX hr hr 70 Figure Plot of Output Voltage Swing RL=100 #4 (V) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 278
279 Table Raw data for Output Voltage Swing RL=100 #4 (V) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Output Voltage Swing RL=100 #4 (V) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E+00 Biased Statistics Average Biased 1.07E E E E E E E E+00 Std Dev Biased 8.37E E E E E E E E-03 Ps90%/90% (+KTL) Biased 1.07E E E E E E E E+00 Ps90%/90% (-KTL) Biased 1.07E E E E E E E E+00 Un-Biased Statistics Average Un-Biased 1.07E E E E E E E E+00 Std Dev Un-Biased 2.07E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 1.07E E E E E E E E+00 Ps90%/90% (-KTL) Un-Biased 1.06E E E E E E E E+00 Specification MAX 1.30E E E E E E E E+00 Status PASS PASS PASS N/A N/A PASS PASS PASS 279
280 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 4.50E-02 Ps90%/90% (-KTL) Un-Biased Specification MIN Maximum Output Source #1 (A) 4.00E E E E E E E E E hr hr 70 Figure Plot of Maximum Output Source #1 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 280
281 Table Raw data for Maximum Output Source #1 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Maximum Output Source #1 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased 4.09E E E E E E E E-02 Std Dev Biased 3.28E E E E E E E E-04 Ps90%/90% (+KTL) Biased 4.18E E E E E E E E-02 Ps90%/90% (-KTL) Biased 4.00E E E E E E E E-02 Un-Biased Statistics Average Un-Biased 4.12E E E E E E E E-02 Std Dev Un-Biased 6.08E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 4.29E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased 3.96E E E E E E E E-02 Specification MIN 2.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 281
282 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 4.50E-02 Ps90%/90% (-KTL) Un-Biased Specification MIN Maximum Output Source #2 (A) 4.00E E E E E E E E E hr hr 70 Figure Plot of Maximum Output Source #2 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 282
283 Table Raw data for Maximum Output Source #2 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Maximum Output Source #2 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased 4.10E E E E E E E E-02 Std Dev Biased 5.47E E E E E E E E-04 Ps90%/90% (+KTL) Biased 4.24E E E E E E E E-02 Ps90%/90% (-KTL) Biased 3.95E E E E E E E E-02 Un-Biased Statistics Average Un-Biased 4.09E E E E E E E E-02 Std Dev Un-Biased 3.95E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 4.19E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased 3.98E E E E E E E E-02 Specification MIN 2.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 283
284 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 4.50E-02 Ps90%/90% (-KTL) Un-Biased Specification MIN Maximum Output Source #3 (A) 4.00E E E E E E E E E hr hr 70 Figure Plot of Maximum Output Source #3 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 284
285 Table Raw data for Maximum Output Source #3 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Maximum Output Source #3 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased 4.11E E E E E E E E-02 Std Dev Biased 6.15E E E E E E E E-04 Ps90%/90% (+KTL) Biased 4.28E E E E E E E E-02 Ps90%/90% (-KTL) Biased 3.94E E E E E E E E-02 Un-Biased Statistics Average Un-Biased 4.09E E E E E E E E-02 Std Dev Un-Biased 3.58E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 4.19E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased 4.00E E E E E E E E-02 Specification MIN 2.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 285
286 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 4.50E-02 Ps90%/90% (-KTL) Un-Biased Specification MIN Maximum Output Source #4 (A) 4.00E E E E E E E E E hr hr 70 Figure Plot of Maximum Output Source #4 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 286
287 Table Raw data for Maximum Output Source #4 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Maximum Output Source #4 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased 4.10E E E E E E E E-02 Std Dev Biased 4.05E E E E E E E E-04 Ps90%/90% (+KTL) Biased 4.21E E E E E E E E-02 Ps90%/90% (-KTL) Biased 3.99E E E E E E E E-02 Un-Biased Statistics Average Un-Biased 4.13E E E E E E E E-02 Std Dev Un-Biased 5.35E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 4.27E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased 3.98E E E E E E E E-02 Specification MIN 2.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 287
288 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased 0.00E+00 Ps90%/90% (+KTL) Un-Biased Specification MAX Maximum Output Sink #1 (A) -5.00E E E E E E E E E hr 168-hr Figure Plot of Maximum Output Sink #1 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 288
289 Table Raw data for Maximum Output Sink #1 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Maximum Output Sink #1 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased -3.84E E E E E E E E-02 Std Dev Biased 1.09E E E E E E E E-04 Ps90%/90% (+KTL) Biased -3.81E E E E E E E E-02 Ps90%/90% (-KTL) Biased -3.87E E E E E E E E-02 Un-Biased Statistics Average Un-Biased -3.87E E E E E E E E-02 Std Dev Un-Biased 3.93E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased -3.76E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased -3.98E E E E E E E E-02 Specification MAX -2.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 289
290 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased 0.00E+00 Ps90%/90% (+KTL) Un-Biased Specification MAX Maximum Output Sink #2 (A) -5.00E E E E E E E E E hr hr 70 Figure Plot of Maximum Output Sink #2 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 290
291 Table Raw data for Maximum Output Sink #2 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Maximum Output Sink #2 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased -3.84E E E E E E E E-02 Std Dev Biased 1.60E E E E E E E E-04 Ps90%/90% (+KTL) Biased -3.80E E E E E E E E-02 Ps90%/90% (-KTL) Biased -3.89E E E E E E E E-02 Un-Biased Statistics Average Un-Biased -3.85E E E E E E E E-02 Std Dev Un-Biased 2.03E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased -3.79E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased -3.91E E E E E E E E-02 Specification MAX -2.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 291
292 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased 0.00E+00 Ps90%/90% (+KTL) Un-Biased Specification MAX Maximum Output Sink #3 (A) -5.00E E E E E E E E E hr 168-hr Figure Plot of Maximum Output Sink #3 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 292
293 Table Raw data for Maximum Output Sink #3 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Maximum Output Sink #3 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased -3.85E E E E E E E E-02 Std Dev Biased 1.80E E E E E E E E-04 Ps90%/90% (+KTL) Biased -3.80E E E E E E E E-02 Ps90%/90% (-KTL) Biased -3.90E E E E E E E E-02 Un-Biased Statistics Average Un-Biased -3.86E E E E E E E E-02 Std Dev Un-Biased 2.18E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased -3.80E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased -3.92E E E E E E E E-02 Specification MAX -2.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 293
294 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased 0.00E+00 Ps90%/90% (+KTL) Un-Biased Specification MAX Maximum Output Sink #4 (A) -5.00E E E E E E E E E hr 168-hr Figure Plot of Maximum Output Sink #4 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 294
295 Table Raw data for Maximum Output Sink #4 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Maximum Output Sink #4 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased -3.84E E E E E E E E-02 Std Dev Biased 1.21E E E E E E E E-04 Ps90%/90% (+KTL) Biased -3.81E E E E E E E E-02 Ps90%/90% (-KTL) Biased -3.88E E E E E E E E-02 Un-Biased Statistics Average Un-Biased -3.87E E E E E E E E-02 Std Dev Un-Biased 3.35E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased -3.78E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased -3.96E E E E E E E E-02 Specification MAX -2.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 295
296 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 9.00E-02 Ps90%/90% (-KTL) Un-Biased Specification MIN Positive Short-Circuit #1 (A) 8.00E E E E E E E E E hr 168-hr Figure Plot of Positive Short-Circuit #1 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 296
297 Table Raw data for Positive Short-Circuit #1 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Short-Circuit #1 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased 8.39E E E E E E E E-02 Std Dev Biased 5.47E E E E E E E E-04 Ps90%/90% (+KTL) Biased 8.54E E E E E E E E-02 Ps90%/90% (-KTL) Biased 8.24E E E E E E E E-02 Un-Biased Statistics Average Un-Biased 8.46E E E E E E E E-02 Std Dev Un-Biased 1.07E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased 8.75E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased 8.17E E E E E E E E-02 Specification MIN 5.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 297
298 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 9.00E-02 Ps90%/90% (-KTL) Un-Biased Specification MIN Positive Short-Circuit #2 (A) 8.00E E E E E E E E E hr 168-hr Figure Plot of Positive Short-Circuit #2 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 298
299 Table Raw data for Positive Short-Circuit #2 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Short-Circuit #2 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased 8.42E E E E E E E E-02 Std Dev Biased 1.07E E E E E E E E-03 Ps90%/90% (+KTL) Biased 8.71E E E E E E E E-02 Ps90%/90% (-KTL) Biased 8.13E E E E E E E E-02 Un-Biased Statistics Average Un-Biased 8.40E E E E E E E E-02 Std Dev Un-Biased 7.24E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 8.60E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased 8.20E E E E E E E E-02 Specification MIN 5.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 299
300 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 9.00E-02 Ps90%/90% (-KTL) Un-Biased Specification MIN Positive Short-Circuit #3 (A) 8.00E E E E E E E E E hr 168-hr Figure Plot of Positive Short-Circuit #3 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 300
301 Table Raw data for Positive Short-Circuit #3 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Short-Circuit #3 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased 8.42E E E E E E E E-02 Std Dev Biased 1.13E E E E E E E E-03 Ps90%/90% (+KTL) Biased 8.73E E E E E E E E-02 Ps90%/90% (-KTL) Biased 8.10E E E E E E E E-02 Un-Biased Statistics Average Un-Biased 8.39E E E E E E E E-02 Std Dev Un-Biased 8.07E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 8.61E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased 8.17E E E E E E E E-02 Specification MIN 5.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 301
302 Average Biased Average Un-Biased Ps90%/90% (-KTL) Biased 9.00E-02 Ps90%/90% (-KTL) Un-Biased Specification MIN Positive Short-Circuit #4 (A) 8.00E E E E E E E E E hr 168-hr Figure Plot of Positive Short-Circuit #4 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 302
303 Table Raw data for Positive Short-Circuit #4 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Positive Short-Circuit #4 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased 8.39E E E E E E E E-02 Std Dev Biased 6.84E E E E E E E E-04 Ps90%/90% (+KTL) Biased 8.57E E E E E E E E-02 Ps90%/90% (-KTL) Biased 8.20E E E E E E E E-02 Un-Biased Statistics Average Un-Biased 8.46E E E E E E E E-02 Std Dev Un-Biased 9.19E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased 8.71E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased 8.20E E E E E E E E-02 Specification MIN 5.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 303
304 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased 0.00E+00 Ps90%/90% (+KTL) Un-Biased Specification MAX Negative Short-Circuit #1 (A) -1.00E E E E E E E E E hr 168-hr Figure Plot of Negative Short-Circuit #1 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 304
305 Table Raw data for Negative Short-Circuit #1 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Short-Circuit #1 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased -7.80E E E E E E E E-02 Std Dev Biased 4.78E E E E E E E E-04 Ps90%/90% (+KTL) Biased -7.67E E E E E E E E-02 Ps90%/90% (-KTL) Biased -7.93E E E E E E E E-02 Un-Biased Statistics Average Un-Biased -7.89E E E E E E E E-02 Std Dev Un-Biased 1.07E E E E E E E E-03 Ps90%/90% (+KTL) Un-Biased -7.60E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased -8.18E E E E E E E E-02 Specification MAX -5.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 305
306 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased 0.00E+00 Ps90%/90% (+KTL) Un-Biased Specification MAX Negative Short-Circuit #2 (A) -1.00E E E E E E E E E hr 168-hr Figure Plot of Negative Short-Circuit #2 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 306
307 Table Raw data for Negative Short-Circuit #2 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Short-Circuit #2 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased -7.84E E E E E E E E-02 Std Dev Biased 8.43E E E E E E E E-04 Ps90%/90% (+KTL) Biased -7.61E E E E E E E E-02 Ps90%/90% (-KTL) Biased -8.07E E E E E E E E-02 Un-Biased Statistics Average Un-Biased -7.83E E E E E E E E-02 Std Dev Un-Biased 5.54E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased -7.68E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased -7.98E E E E E E E E-02 Specification MAX -5.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 307
308 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased 0.00E+00 Ps90%/90% (+KTL) Un-Biased Specification MAX Negative Short-Circuit #3 (A) -1.00E E E E E E E E E hr 168-hr Figure Plot of Negative Short-Circuit #3 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 308
309 Table Raw data for Negative Short-Circuit #3 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Short-Circuit #3 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased -7.84E E E E E E E E-02 Std Dev Biased 8.69E E E E E E E E-04 Ps90%/90% (+KTL) Biased -7.60E E E E E E E E-02 Ps90%/90% (-KTL) Biased -8.08E E E E E E E E-02 Un-Biased Statistics Average Un-Biased -7.82E E E E E E E E-02 Std Dev Un-Biased 6.49E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased -7.64E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased -8.00E E E E E E E E-02 Specification MAX -5.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 309
310 Average Biased Average Un-Biased Ps90%/90% (+KTL) Biased 0.00E+00 Ps90%/90% (+KTL) Un-Biased Specification MAX Negative Short-Circuit #4 (A) -1.00E E E E E E E E E hr 168-hr Figure Plot of Negative Short-Circuit #4 (A) versus total dose. The solid diamonds are the average of the measured data points for the samples irradiated under electrical bias while the shaded diamonds are the average of the measured data points for the samples irradiated with all pins tied to ground. The black lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated under electrical bias while the gray lines (solid and/or dashed) are the average of the data points after application of the KTL statistics on the samples irradiated in the unbiased condition. The red dotted line(s) are the pre- and/or post-irradiation minimum and/or maximum specification value as defined in the datasheet and/or test plan. 310
311 Table Raw data for Negative Short-Circuit #4 (A) versus total dose, including the statistical analysis, specification and the status of the testing (pass/fail). Negative Short-Circuit #4 (A) 24-hr 168-hr Device E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E-02 Biased Statistics Average Biased -7.81E E E E E E E E-02 Std Dev Biased 4.21E E E E E E E E-04 Ps90%/90% (+KTL) Biased -7.69E E E E E E E E-02 Ps90%/90% (-KTL) Biased -7.92E E E E E E E E-02 Un-Biased Statistics Average Un-Biased -7.88E E E E E E E E-02 Std Dev Un-Biased 8.67E E E E E E E E-04 Ps90%/90% (+KTL) Un-Biased -7.65E E E E E E E E-02 Ps90%/90% (-KTL) Un-Biased -8.12E E E E E E E E-02 Specification MAX -5.50E E E E E E E E-02 Status PASS NA NA NA NA NA NA NA 311
312 6.0. Summary / Conclusions The low dose rate testing described in this final report was performed using the facilities at Radiation Assured Devices' Longmire Laboratories in Colorado Springs, CO. The low dose rate source is a GB- 150 irradiator modified to provide a panoramic exposure. The Co-60 rods are held in the base of the irradiator heavily shielded by lead. During the irradiation exposures the rod is raised by an electronic timer/controller and the exposure is performed in air. The dose rate for this irradiator in this configuration ranges from approximately 1mrad(Si)/s to a maximum of approximately 50rad(Si)/s, determined by the distance from the source. The parametric data was obtained as "read and record" and all the raw data plus an attributes summary are contained in this report as well as in a separate Excel file. The attributes data contains the average, standard deviation and the average with the KTL values applied. The KTL value used in this work is per MIL-HDBK-814 using one sided tolerance limits of 90/90 and a 5-piece sample size. The 90/90 KTL values were selected to match the statistical levels specified in the MIL-PRF sampling plan for the qualification of a radiation hardness assured (RHA) component. Note that the following criteria must be met for a device to pass the low dose rate test: following the radiation exposure each of the 5 pieces irradiated under electrical bias shall pass the specification value. The units irradiated without electrical bias and the KTL statistics are included in this report for reference only. If any of the 5 pieces irradiated under electrical bias exceed the datasheet specifications, then the lot could be logged as a failure. Based on this criterion the RH1814MW Quad Operational Amplifier (from the lot date code identified on the first page of this test report) PASSED the enhanced low dose rate sensitivity test to the maximum tested dose level of 50krad(Si) with all parameters remaining within their datasheet specifications. Further, the data in this report can be analyzed along with the high dose rate report titled "Total Ionizing Dose (TID) Radiation Testing of the RH1814MW Quad Op Amp for Linear Technology" to demonstrate that these parts do not exhibit ELDRS as defined in the current test method. 312
313 Appendix A: Photograph of device-under-test to show part markings 313
Enhanced Low Dose Rate Sensitivity (ELDRS) Radiation Testing of the RH118W Op-Amp for Linear Technology
Enhanced Low Dose Rate Sensitivity (ELDRS) Radiation Testing of the RH118W Op-Amp for Linear Technology Customer: Linear Technology, PO# 60225L RAD Job Number: 11-351 Part Type Tested: RH118W Op-Amp, RH118
More informationEnhanced Low Dose Rate Sensitivity (ELDRS) Radiation Testing of the RH1498MW Dual Precision Op Amp for Linear Technology
Enhanced Low Dose Rate Sensitivity (ELDRS) Radiation Testing of the RH1498MW Dual Precision Op Amp for Linear Technology Customer: Linear Technology (PO# 54873L) RAD Job Number: 09-579 Part Type Tested:
More informationEnhanced Low Dose Rate Sensitivity (ELDRS) Radiation Testing of the RH117H-Positive Adjustable Regulator for Linear Technology
Enhanced Low Dose Rate Sensitivity (ELDRS) Radiation Testing of the RH117H-Positive Adjustable Regulator for Linear Technology Customer: Linear Technology (PO# 55339L) RAD Job Number: 10-121 Part Type
More informationEnhanced Low Dose Rate Sensitivity (ELDRS) of the RH1078MJ8 Dual Precision Op Amp for Linear Technology
Enhanced Low Dose Rate Sensitivity (ELDRS) of the RH1078MJ8 Dual Precision Op Amp for Linear Technology Customer: Linear Technology, PO# 54873L RAD Job Number: 09-578 Part Type Tested: Linear Technology
More informationEnhanced Low Dose Rate Sensitivity (ELDRS) Radiation Testing of the RH1086MK Low Dropout Positive Adjustable Regulator for Linear Technology
Enhanced Low Dose Rate Sensitivity (ELDRS) Radiation Testing of the RH1086MK Low Dropout Positive Adjustable Regulator for Linear Technology Customer: Linear Technology, PO# 54886L RAD Job Number: 10-006
More informationProducts contained in this shipment may be subject to ITAR regulations.
Products contained in this shipment may be subject to ITAR regulations. Warning: The export of these commodity(ies), technology, or software are subject either to the U.S. Commerce Department Export Administration
More informationTotal Ionizing Dose (TID) Radiation Testing of the RH1016MW UltraFast Precision Comparator for Linear Technology
Total Ionizing Dose (TID) Radiation Testing of the RH1016MW UltraFast Precision Comparator for Linear Technology Customer: Linear Technology (PO 53101L) RAD Job Number: 09-288 Part Type Tested: Linear
More informationRadiation Lot Acceptance Testing (RLAT) of the RH1014MW Quad Precision Operational Amplifier for Linear Technology
Radiation Lot Acceptance Testing (RLAT) of the RH1014MW Quad Precision Operational Amplifier for Linear Technology Customer: Linear Technology, PO# 62118L RAD Job Number: 12-214 Part Type Tested: RH1014MW
More informationRadiation Lot Acceptance Testing (RLAT) of the RH1014MW Quad Precision Operational Amplifier for Linear Technology
Radiation Lot Acceptance Testing (RLAT) of the RH1014MW Quad Precision Operational Amplifier for Linear Technology Customer: Linear Technology, PO# 61846L RAD Job Number: 12-085 Part Type Tested: RH1014MW
More informationRadiation Lot Acceptance Testing (RLAT) of the RH137H Negative Adjustable Regulator for Linear Technology
Radiation Lot Acceptance Testing (RLAT) of the RH137H Negative Adjustable Regulator for Linear Technology Customer: Linear Technology, PO# 61631L RAD Job Number: 11-771 Part Type Tested: RH137H Negative
More informationRadiation Lot Acceptance Testing (RLAT) of the RH1498MW Dual Rail-to- Rail Input and Output Precision C-Load Op Amp for Linear Technology
Radiation Lot Acceptance Testing (RLAT) of the RH1498MW Dual Rail-to- Rail Input and Output Precision C-Load Op Amp for Linear Technology Customer: Linear Technology, PO# 58876L RAD Job Number: 11-009
More informationRadiation Lot Acceptance Testing (RLAT) of the RH1016MW UltraFast Precision Comparator for Linear Technology
Radiation Lot Acceptance Testing (RLAT) of the RH1016MW UltraFast Precision Comparator for Linear Technology Customer: Linear Technology (PO 55080L) RAD Job Number: 10-041 Part Type Tested: Linear Technology
More informationProducts contained in this shipment may be subject to ITAR regulations.
Products contained in this shipment may be subject to ITAR regulations. Warning: The export of these commodity(ies), technology, or software are subject either to the U.S. Commerce Department Export Administration
More informationRadiation Lot Acceptance Testing (RLAT) of the RH6200MW Low Noise Rail-to-Rail Input and Output Op Amp for Linear Technology
Radiation Lot Acceptance Testing (RLAT) of the RH6200MW Low Noise Rail-to-Rail Input and Output Op Amp for Linear Technology Customer: Linear Technology, PO# 7128F RAD Job Number: 10-447 Part Type Tested:
More informationTotal Ionizing Dose (TID) Radiation Testing of the RH1009MH 2.5V Voltage Reference for Linear Technology
Total Ionizing Dose (TID) Radiation Testing of the RH1009MH 2.5V Voltage Reference for Linear Technology Customer: Linear Technology, PO# 57799L RAD Job Number: 10-471 Part Type Tested: RH1009MH 2.5V Voltage
More informationProducts contained in this shipment may be subject to ITAR regulations.
Products contained in this shipment may be subject to ITAR regulations. Warning: The export of these commodity(ies), technology, or software are subject either to the U.S. Commerce Department Export Administration
More informationRadiation Lot Acceptance Testing (RLAT) of the RH1009MH 2.5V Voltage Reference for Linear Technology
Radiation Lot Acceptance Testing (RLAT) of the RH1009MH 2.5V Voltage Reference for Linear Technology Customer: Linear Technology, PO# 62118L RAD Job Number: 12-213 Part Type Tested: RH1009MH 2.5V Voltage
More informationRadiation Lot Acceptance Testing (RLAT) of the RH1013MJ8 Dual Precision Operational Amplifier for Linear Technology
Radiation Lot Acceptance Testing (RLAT) of the RH1013MJ8 Dual Precision Operational Amplifier for Linear Technology Customer: Linear Technology, PO# 51419L RAD Job Number: 08-402 Part Type Tested: Linear
More informationProducts contained in this shipment may be subject to ITAR regulations.
Products contained in this shipment may be subject to ITAR regulations. Warning: The export of these commodity(ies), technology, or software are subject either to the U.S. Commerce Department Export Administration
More informationRadiation Lot Acceptance Test (RLAT) of the RH27CW Precision Op Amp for Linear Technology
Radiation Lot Acceptance Test (RLAT) of the RH27CW Precision Op Amp for Linear Technology Customer: Linear Technology, PO 49797L RAD Job Number: 08-136 Part Type Tested: Linear Technology RH27CW Precision
More informationTOTAL DOSE STEADY-STATE IRRADIATION TEST METHOD. ESCC Basic Specification No
Page 1 of 22 TOTAL DOSE STEADY-STATE IRRADIATION TEST METHOD ESCC Basic Specification Issue 5 June 2016 Document Custodian: European Space Agency see https://escies.org PAGE 2 LEGAL DISCLAIMER AND COPYRIGHT
More informationTotal dose testing of the ISL78845ASRH current mode PWM controller
Total dose testing of the ISL78845ASRH current mode PWM controller Nick van Vonno Intersil Corporation Revision 2 April 2013 Table of Contents 1. Introduction 2. Reference Documents 3. Part Description
More informationTotal Ionizing Dose Test Report. Z-Series DC-DC Converter
Total Ionizing Dose Test Report Z-Series DC-DC Converter Revision A March, 2004 TOTAL DOSE TEST REPORT for Z - SERIES DC/DC CONVERTER Project Engineer: Engineering Director: Tom Hanson Peter Lee TABLE
More informationTotal dose testing of the IS-1825ASRH Dual Output PWM
Total dose testing of the IS-1825ASRH Dual Output PWM Nick van Vonno Intersil Corporation Revision 0 October 2010 Revision 1 June 2012 Table of Contents 1. Introduction 2. Reference Documents 3. Part Description
More informationCMOS Quad Rail-to-Rail I/O Op Amp DESCRIPTION: FEATURES: Logic Diagram
6484 CMOS Quad Rail-to-Rail I/O Op Amp V+ IN+A IN+D IN-A OUT A OUT D IN-D V- IN+B OUT B OUT C IN+C IN-B Logic Diagram IN-C FEATURES: Rad-Pak technology-hardened against natural space radiation Total dose
More informationTOTAL IONIZING DOSE TEST REPORT No. 03T-RT54SX32S-T25JS004 March 12, 2003
J.J. Wang (408) 522-4576 jih-jong.wang@actel.com TOTAL IONIZING DOSE TEST REPORT No. 03T-RT54SX32S-T25JS004 March 12, 2003 I. SUMMARY TABLE Parameter Tolerance 1. Gross Functionality Passed 100 krad(si)
More informationThis document and process conversion measures necessary to comply with this revision shall be completed by 30 September 2003 DEPARTMENT OF DEFENSE
Notice of Change This document and process conversion measures necessary to comply with this revision shall be completed by 30 September 2003 INCH-POUND 7 March 2003 DEPARTMENT OF DEFENSE TEST METHOD STANDARD
More informationMilitary Performance Specifications
RADIATION OWNER S MANUAL RHA-Related Documents Military Performance Specifications 19500 General Specification for Semiconductor Devices 38534 Performance Specifications for Hybrid Microcircuits 38535
More informationTOTAL IONIZING DOSE TEST REPORT No. 03T-RT54SX7S-T25KS006 April 25, 2003
J.J. Wang (408) 522-4576 jih-jong.wang@actel.com TOTAL IONIZING DOSE TEST REPORT No. 03T-RT54SX7S-T25KS006 April 25, 2003 I. SUMMARY TABLE Parameter Tolerance 1. Gross Functionality Passed 100 krad(si)
More informationREVISION RECORD REV DESCRIPTION DATE 0 INITIAL RELEASE 06/24/03
REVISION RECORD REV DESCRIPTION DATE 0 INITIAL RELEASE 06/24/03 A PAGE 3, CHANGED INITIAL RATE OF RADS TO 240 RADS/SEC. 03/15/05 B PAGE 4, CHANGED IN BOTH PARAGRAPHS 4.2, 4.3 IN CONJUNCTION TO 3.3 CHANGED
More informationDLA LAND AND MARITIME COLUMBUS, OHIO STANDARD MICROCIRCUIT DRAWING
REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Paragraph 1.4; added V control range (Voltages are relative to V OUT) +2 V to +36 V. Figure 2; corrected the terminal symbol names. Figure 3; corrected
More informationREVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Corrected title mis-spelling. Added cage code for device type
REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Corrected title mis-spelling. Added cage code for device type 10-01-20 Charles F. Saffle 02. Removed footnote 3 from the Standrard Microcircuit Drawing
More informationNeutron testing of the ISL70417SEH hardened quad operational amplifier
Neutron testing of the ISL7417SEH hardened quad operational amplifier Nick van Vonno Intersil Corporation 5 April 213 Revision 1 Table of Contents 1. Introduction 2. Part Description 3. Test Description
More informationREVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Added vendor CAGE Added case outline G. Added device type M.A.
REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Added vendor CAGE 27014. Added case outline G. Added device type 02. 94-07-21 M.A. FRYE B Updated boilerplate. Added case outline P. Added delta table
More informationREVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED. E Update boilerplate paragraphs to current MIL-PRF requirements. -rrp C.
REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A B C D Change to one part-one number format. Add table III. Editorial changes throughout. Make changes to Slew rate test as specified under Table I.
More informationDesign, Development and Irradiation Testing of 3-Channel Preamplifier for Ultrasonic NDT
Design, Development and Irradiation Testing of 3-Channel Preamplifier for Ultrasonic NDT Shiv KUMAR 1, S. K. LALWANI 1, P. P. NANEKAR 2 and Anita BEHERE 1 1 Electronics Division, BARC, Mumbai, India More
More informationSTANDARD MICROCIRCUIT DRAWING MICROCIRCUIT, LINEAR, RADIATION HARDENED, PRECISION INSTRUMENTATION AMPLIFIER, MONOLITHIC SILICON
REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add case outline 2. Add input voltage test. Add footnote 3/. Editorial changes throughout. 90-03-30 M. POELKIN B Change boilerplate to add one-part
More informationSTANDARD MICROCIRCUIT DRAWING
REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED REV REV 15 16 17 18 19 20 21 22 REV STATUS REV OF S 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY
More informationREVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED
REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add case X which is a 16 lead flat pack. Make changes to 1.2.4, 1.3, 3.2.1, 3.2.2, figure 1, slew rate test, and footnote 1 as specified in table I
More informationEvaluation of the Radiation Tolerance of Several Generations of SiGe Heterojunction Bipolar Transistors Under Radiation Exposure
1 Evaluation of the Radiation Tolerance of Several Generations of SiGe Heterojunction Bipolar Transistors Under Radiation Exposure J. Metcalfe, D. E. Dorfan, A. A. Grillo, A. Jones, F. Martinez-McKinney,
More informationREVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED. C Add paragraph and Appendix A for microcircuit die. - ro C.
REVISIONS LTR ESCRIPTION ATE (YR-MO-A) APPROVE A Add device type 02. Add enhanced low dose rate sensitivity (ELRS) free requirements. - ro 10-03-17 C. SAFFLE B elete footnote 2/ from final electrical parameters
More informationICS Radiation Test Results F2812 DSP
ICS Radiation Test Results F2812 DSP Texas Instruments ================================================== TI P.O. Number 4500023746...... DEVICE TYPE: F2812 DSP (TI).. RADIATION SOURCE: Neeley Nuclear
More informationREVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED. D Add radiation hardened requirements. - ro R. MONNIN
REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Make change to input offset voltage tests as specified under sections; V S = +5 V, V CM = 2.5 V and V S = +3 V, V CM = 1.5 V in table I. - ro 00-11-28
More informationHMXCMP01 Radiation Hardened Comparator
HMXCMP01 Radiation Hardened Comparator Features PRODUCTION - Release - 22 Jul 201 12:8:17 MST - Printed on 31 Jan 2017 Rad Hard 300krad (Si) Analog supply voltage:.75v to 5.25V Digital supply voltage:
More informationRHFAHC00. Rad-Hard, quad high speed NAND gate. Datasheet. Features. Applications. Description
Datasheet Rad-Hard, quad high speed NAND gate Features 1.8 V to 3.3 V nominal supply 3.6 V max. operating 4.8 V AMR Very high speed: propagation delay of 3 ns maximum guaranteed Pure CMOS process CMOS
More informationCONTINUED ON NEXT PAGE..
REVISION RECORD REV DESCRIPTION DATE 0 INITIAL RELEASE 07/23/96 A PAGE 2: ADDED PARAGRAPHS 3.2.1, 3.2.2, AND 3.2.3. PARAGRAPH 3.3.b, ADDED SEE PARAGRAPH 3.2. 12/11/97 PAGE 3: ADDED PARAGRAPHS 3.8.1, 3.8.2,
More informationVoltage Regulator VRG8669
Voltage Regulator VRG8669 2.5A ULDO Adjustable Positive Voltage Regulator Datasheet Cobham.com/HiRel November 2, 2017 The most important thing we build is trust FEATURES Manufactured using Space Qualified
More informationTOTAL IONIZING DOSE TEST REPORT No. 01T-RT54SX32-T6JP04 April 2, 2001
TOTAL IONIZING DOSE TEST REPORT No. 01T-RT54SX32-T6JP04 April 2, 2001 J.J. Wang Igor Kleyner (408) 522-4576 (301) 286-5683 jih-jong.wang@actel.com igor.kleyner@gsfc.nasa.gov I. SUMMARY TABLE Parameters
More informationLow-Power Quad Operational Amplifier FEATURES: DESCRIPTION: Memory. Logic Diagram. RAD-PAK technology-hardened against natural space radiation
Low-Power Quad Operational Amplifier FEATURES: RAD-PAK technology-hardened against natural space radiation Total dose hardness: - > 100 krad (Si), depending upon space mission Excellent Single Event Effects:
More informationTOTAL IONIZING DOSE TEST REPORT No. 01T-RT54SX32-T6JP05 Jan. 4, 2001
TOTAL IONIZING DOSE TEST REPORT No. 01T-RT54SX32-T6JP05 Jan. 4, 2001 J.J. Wang Igor Kleyner (408) 522-4576 (301) 286-5683 jih-jong.wang@actel.com igor.kleyner@gsfc.nasa.gov I. SUMMARY TABLE Parameters
More informationSTANDARD MICROCIRCUIT DRAWING MICROCIRCUIT, DIGITAL, ASIC, CMOS GATE ARRAY, SPACEWIRE ROUTER, MONOLITHIC SILICON A03
REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED REV REV REV STATUS REV OF S 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES
More informationPrerelease product(s)
Datasheet Aerospace 60 A - 200 V fast recovery rectifier STTH60200CSA1 31218 FR SMD1 Features Very small conduction losses Negligible switching losses High surge current capability Hermetic package TID
More informationREVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED. A Drawing updated to reflect current requirements. gt R. Monnin
REVISIONS LTR DESRIPTION DATE (YR-MO-DA) APPROVED A Drawing updated to reflect current requirements. gt 02-09-09 R. Monnin B Five year review requirement. -rrp 08-11-17 R. HEBER Add case outline H. Add
More informationTOTAL IONIZATION DOSE TEST REPORT
TOTAL IONIZATION DOSE TEST REPORT June 8, 1999 No. 99T-RT54SX16-P05 J. J. Wang (408)522-4576 jih-jong.wang@actel.com 1.0 SUMMARY TABLE RT54SX16A Parameters/Characteristics Results 1. Functionality Passed
More informationSTANDARD MICROCIRCUIT DRAWING MICROCIRCUIT, LINEAR, JFET INPUT OPERATIONAL AMPLIFIER, MONOLITHIC SILICON
REVISIONS LTR DESCRIPTION DTE (YR-MO-D) PPROVED Delete references to device class M requirements. Update document paragraphs to current MIL-PRF-38535 requirements. - ro 17-10-04 C. SFFLE REV REV REV STTUS
More informationSTANDARD MICROCIRCUIT DRAWING MICROCIRCUIT, LINEAR, QUAD, RAIL-TO-RAIL, PRECISION, OPERATIONAL AMPLIFIER, MONOLITHIC SILICON
RVISIONS LTR DSCRIPTION DAT (YR-MO-DA) APPROVD A Make change to input offset voltage tests as specified under sections; V S = +5 V, V CM = 2.5 V and V S = +3 V, V CM = 1.5 V in table I. - ro 00-11-28 R.
More informationREVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED. A Add radiation hardened and class V requirements. - ro R. MONNIN
REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add radiation hardened and class V requirements. - ro 00-04-13 R. MONNIN B C Make change to A VO radiation hardened test limit as specified under table
More informationPrerelease product(s)
Datasheet Aerospace 40 A - 200 V fast recovery rectifier A1 K A2 TO-254AA The TO-254-AA is a metallic package. It is not connected to any pin nor to the inside die. Features Very small conduction losses
More informationSTANDARD MICROCIRCUIT DRAWING MICROCIRCUIT, LINEAR, SINGLE, ULTRAFAST COMPARATOR, MONOLITHIC SILICON
REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Drawing updated to reflect current requirements. - gt 02-04-24 R. MONNIN Add radiation hardness assurance requirements. -rrp 02-07-29 R. MONNIN REV
More informationREVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Drawing updated to reflect current requirements. - ro R. MONNIN
REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Drawing updated to reflect current requirements. - ro 02-04-18 R. MONNIN B C D E Make a change to footnote 1/ under Table I. Make changes to +V OUT
More informationREVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED. A Drawing updated to reflect current requirements. gt R. Monnin
REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Drawing updated to reflect current requirements. gt 03-04-04 R. Monnin Drawing updated to reflect current MIL-PRF-38535 requirements. - ro 12-03-15
More informationDLA LAND AND MARITIME COLUMBUS, OHIO STANDARD MICROCIRCUIT DRAWING
REVISIONS LTR ESCRIPTION ATE (YR-MO-A) APPROVE A B C Added Enhanced Low ose Rate Sensitivity (ELRS) testing. Figure 1; corrected dimension "b1" min and max from ".220 and.230" Inches to ".195 and.205"
More informationREVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add device types 02 and 03. Make change to the NPN and PNP
REVISIONS LTR DESRIPTION DATE (YR-MO-DA) APPROVED A Add device types 02 and 03. Make change to the NPN and PNP 08-04-08 R. HEBER characteristics h FE tests as specified under Table I. Delete NPN and PNP
More informationTotal Dose Testing of Advanced Mixed Signal ADC/DAC Microcircuits
Total Dose Testing of Advanced Mixed Signal ADC/DAC Microcircuits David Alexander, Senior Member IEEE, Alonzo Vera Member IEEE, James Aarestad, Member IEEE, Gabriel V. Urbaitis Abstract-- Total dose test
More informationTotal dose testing of the ISL706ARH radiation hardened microprocessor supervisory circuit
Total dose testing of the ISL76ARH radiation hardened microprocessor supervisory circuit Nick van Vonno Intersil Corporation Revision 1 February 212 Table of Contents 1. Introduction 2. Reference Documents
More informationMICROCIRCUIT, HYBRID, 12 VOLT, DUAL CHANNEL, DC/DC CONVERTER
REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED REV REV REV STATUS REV OF S 1 2 3 4 5 6 7 8 9 10 PMIC N/A MICROCIRCUIT DRAWING PREPARED BY Steve Duncan CHECKED BY Greg Cecil http://www.dscc.dla.mil
More informationTotal Ionizing Dose (TID) and Single Event Effects (SEE) Test Report
Total Ionizing Dose (TID) and Single Event Effects (SEE) Test Report TEXAS INSTRUMENTS Low Drop Out ( LDO) Regulator TPS7H1101 SP QMLV SMD#: 5962-1320201VXC James F. Salzman Courtesy Michael Konig Date:
More informationREVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED. E Add device type 04 to footnotes 1/ and 4/ as specified under Table I. - ro C.
REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add paragraph 3.1.1 and Appendix A for microcircuit die. Changes in accordance with N.O.R. 5962-R014-98. 97-12-21 Raymond Monnin B Make changes to boilerplate
More informationREVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED. B Drawing updated to reflect current requirements. -rrp R. MONNIN
REVISIONS LTR ESCRIPTION ATE (YR-MO-A) APPROVE A Add device classes Q and V requirements and radiation hardened requirements. Add case outline 2. -ro 00-07-17 R. MONNIN B rawing updated to reflect current
More informationREVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED. A Changes to slew rate test. Changes IAW NOR 5962-R M. A. FRYE
REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes to slew rate test. Changes IAW NOR 5962-R194-93. 93-08-25 M. A. FRYE B Changes boilerplate to add one-part numbers. Add device type 03. Add
More informationRadiation Test Report Paul Scherer Institute Proton Irradiation Facility
the Large Hadron Collider project CERN CH-2 Geneva 23 Switzerland CERN Div./Group RadWG EDMS Document No. xxxxx Radiation Test Report Paul Scherer Institute Proton Irradiation Facility Responsibility Tested
More informationREVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED
REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Make correction to group A subgroups 2 and 3 for output voltage high, (V OH ), test with conditions V S = 15.0 V and R L = 2 kω in table I. -rrp 15-12-01
More informationRH1078M Micropower, Dual, Single Supply Precision Op Amp ABSOLUTE MAXIMUM RATINGS DESCRIPTION PACKAGE/ORDER INFORMATION
RH7M Micropower, Dual, Single Supply Precision Op Amp DESCRIPTION The RH7M is a micropower dual op amp in the standard -pin configuration. This device is optimized for single supply operation at 5. Specifications
More informationRH1014M Quad Precision Operational Amplifier DESCRIPTIO PACKAGE INFORMATION BURN-IN CIRCUIT
RH4M Quad Precision Operational Amplifier DESCRIPTIO U The RH4M is the first precision quad operational amplifier which directly upgrades designs in the industry standard 8-pin DIP LM4/LM48/OP-/556 pin
More informationTECHNICAL DATA. benefits
benefits > Instant & direct, non-destructive reading of radiation dose > Zero or very low power consumption > Large dynamic range > Smallest active volume of all dosimeters > Easily integrated into an
More informationRH3083MK DICE/DWF Adjustable 2.8A Single Resistor Low Dropout Regulator
RH383MK DICE/DWF Adjustable.8A Single Resistor Low Dropout Regulator Features n Outputs May Be Paralleled for Higher Current and Heat Spreading n Single Resistor Sets Output oltage n Output Adjustable
More informationSTANDARD MICROCIRCUIT DRAWING MICROCIRCUIT, LINEAR, WIDEBAND, DIFFERENTIAL OPERATIONAL AMPLIFIER, MONOLITHIC SILICON
REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Change table II to have a higher V IO delta limit for life test than for burn-in. rrp Update drawing to current MIL-PRF-38535 requirements. Removed
More informationU U W PACKAGE I FOR ATIO. RH1498M 10MHz, 6V/µs, Dual Rail-to-Rail Input and Output Precision C-Load Op Amp DESCRIPTIO BUR -I CIRCUIT
RH498M MHz, 6V/µs, Dual Rail-to-Rail Input and Output Precision C-Load Op Amp DESCRIPTIO U The RH498 is a dual, rail-to-rail input and output precision C-Load TM op amp with a MHz gain-bandwidth product
More informationFTM2 Series HCMOS/TTL OSCILLATORS FOR SPACE APPLICATIONS 0.5MHz to 160 MHz. ( 5 x 3.2 mm, SMD, 2.5 V )
REV LTR DESCRIPTION DATE APPVD. - Orig. Release 6/22/09 RBT A Corrected P/N on Pages 1 and 2 5/08/14 RBT B Revised per ECN 2015-1 9/12/15 RBT C Revised per ECN 2016-1 9/18/16 RBT FTM2 Series HCMOS/TTL
More informationMICROCIRCUIT, HYBRID, 5 VOLT, SINGLE CHANNEL, DC/DC CONVERTER
REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED REV REV REV STATUS REV OF S 1 2 3 4 5 6 7 8 9 10 PMIC N/A MICROCIRCUIT DRAWING PREPARED BY Steve Duncan CHECKED BY Greg Cecil http://www.dscc.dla.mil
More informationREVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED. C Add Appendix A for microcircuit die. Redrawn. - ro R. MONNIN
REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A B Sheet 6: Table I, Output current test, -I OUT ; add M, D, L, R box to the conditions column and add -7 ma max to the limits column for that condition.
More informationSTANDARD MICROCIRCUIT DRAWING MICROCIRCUIT, DIGITAL-LINEAR, 14-BIT, 400 MSPS, ANALOG-TO-DIGITAL CONVERTER, MONOLITHIC SILICON
REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED REV REV 15 REV STATUS REV OF S 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND
More informationTEST REPORT. Introduction. Test Description. Related Literature. Part Description ISL70617SEH. Irradiation Facilities.
TEST REPORT ISL70617SEH TR041 Rev 0.00 Introduction This report provides results of a Total Ionizing Dose (TID) test of the ISL70617SEH instrumentation amplifier. The test was conducted in order to determine
More informationExtended TID, ELDRS and SEE Hardening and Testing on Mixed Signal Telemetry LX7730 Controller
Extended TID, ELDRS and SEE Hardening and Testing on Mixed Signal Telemetry LX7730 Controller Mathieu Sureau, Member IEEE, Russell Stevens, Member IEEE, Marco Leuenberger, Member IEEE, Nadia Rezzak, Member
More informationREVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED. D Update boilerplate to meet current requirements. rrp R. MONNIN
REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A B C Page 6, table I: Delete input resistance (RIN). Page 4, table I: Corrected errors in conditions column. Editorial changes throughout. Page 5, table
More informationMICROCIRCUIT, HYBRID, 12 VOLT, SINGLE CHANNEL, DC/DC CONVERTER
REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED REV REV REV STATUS REV OF S 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A MICROCIRCUIT DRAWING PREPARED BY Steve L. Duncan CHECKED BY Greg Cecil http://www.dscc.dla.mil/
More informationREVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED. A Changes in accordance with NOR 5962-R M. A. FRYE
REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with NOR 5962-R140-96. 96-06-12 M. A. RYE B C Add device type 02. Add RHA requirements. Add case outlines G, H, and P. Changes
More informationSTANDARD MICROCIRCUIT DRAWING
REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Make change to title of Table II and footnote 1/ under Table II. Update boilerplate paragraphs to current MIL-PRF-38535 requirements. - ro 10-10-11
More informationAMICSA Bridging Science & Applications F r o m E a r t h t o S p a c e a n d b a c k. Kayser-Threde GmbH. Space
Bridging Science & Applications F r o m E a r t h t o S p a c e a n d b a c k E a r t h S p a c e & F u t u r e Kayser-Threde GmbH Space Industrial Applications AMICSA 2008 First radiation test results
More informationOX-249 Space Qualified Oven Controlled Crystal Oscillator (OCXO)
Common Characteristics [all frequencies and options] Supply voltage 4.75 5.0 5.25 VDC Power consumption (in air) Frequency vs. Temperature (ref. frequency at 60 minutes) Warm-up Accuracy @+25 C, (ref.
More informationMICROCIRCUIT, HYBRID, DUAL VOLTAGE REGULATOR, POSTIVE AND NEGATIVE, ADJUSTABLE
REVISIONS LTR ESCRIPTION ATE (YR-MO-A) APPROVE A B C Added device type 03 and 04. Paragraph 1.4 changed the output voltage, negative voltage regulator for device type 01 from -1.2 V to -22 V dc to -1.2
More informationANALYSIS OF TOTAL DOSE EFFECTS IN A LOW-DROPOUT VOLTAGE REGULATOR. Vishwa Ramachandran. Thesis. Submitted to the Faculty of the
ANALYSIS OF TOTAL DOSE EFFECTS IN A LOW-DROPOUT VOLTAGE REGULATOR By Vishwa Ramachandran Thesis Submitted to the Faculty of the Graduate School of Vanderbilt University in partial fulfillment of the requirements
More informationDual, Zero Drift, Single-Supply, Rail-to-Rail I/O, Operational Amplifier. Radiation tested to 10Krads (Si)
1.0 Scope Zero-Drift, Single-Supply Rail-to-Rail Input/Output Operational Amplifier AD8629S 1.1. This specification documents the detail requirements for space qualified product manufactured on Analog
More informationREDI. M. Wind (SL), P. Beck (SL), M. Latocha (SL), S. Metzger (INT), M. Poizat(ESA), M. Steffens (INT)
REDI Radiation evaluation of digital isolators currently available, suitable for space missions in terms of radiation tolerance (TID and SEE) including the JUICE mission M. Wind (SL), P. Beck (SL), M.
More informationMICROCIRCUIT, HYBRID, LINEAR, ±5 VOLT, DUAL CHANNEL, DC/DC CONVERTER
REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED REV REV REV STATUS PMIC N/A MICROCIRCUIT DRAWING REV PREPARED BY Steve Duncan CHECKED BY Greg Cecil 1 2 3 4 5 6 7 8 9 10 11 http://www.dscc.dla.mil/ THIS
More informationTOTAL IONIZING DOSE CHARACTERIZATION OF A COMMERCIALLY FABRICATED ASYNCHRONOUS FFT FOR SPACE APPLICATIONS *
TOTAL IONIZING DOSE CHARACTERIZATION OF A COMMERCIALLY FABRICATED ASYNCHRONOUS FFT FOR SPACE APPLICATIONS * D. Barnhart, P. Duggan, B. Suter Air Force Research Laboratory C. Brothers Air Force Institute
More informationSTANDARD MICROCIRCUIT DRAWING MICROCIRCUIT, LINEAR, ULTRA LOW NOISE, PRECISION VOLTAGE REFERENCE, MONOLITHIC SILICON
REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED REV REV 15 16 17 18 19 20 REV STATUS REV OF S 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL
More informationDUAL+2.5V RAD HARD PRECISION VOLTAGE REFERENCE
MIL-PRF-38534 CERTIFIED FACILITY M.S.KENNEDY CORP. 4707 Dey Road Liverpool, N.Y. 13088 DUAL+2.5V RAD HARD PRECISION VOLTAGE REFEREE 110RH (315) 701-751 FEATURES: Manufactured using Space Qualified RH1009
More information3084 IEEE TRANSACTIONS ON NUCLEAR SCIENCE, VOL. 60, NO. 4, AUGUST 2013
3084 IEEE TRANSACTIONS ON NUCLEAR SCIENCE, VOL. 60, NO. 4, AUGUST 2013 Dummy Gate-Assisted n-mosfet Layout for a Radiation-Tolerant Integrated Circuit Min Su Lee and Hee Chul Lee Abstract A dummy gate-assisted
More informationREVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED
REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Change to military drawing format. Changes to output adjustment range. Add conditions for load regulation test at -55 C and +125 C. Change group A subgroups
More information