AE Agricultural Customer Services Play-by-Play Tekscope Manual
|
|
- Debra Shelton
- 5 years ago
- Views:
Transcription
1 AE Agricultural Customer Services Play-by-Play Tekscope Manual TABLE OF CONTENTS I. Definitions II. Waveform Properties 1 III. Scientific Notation... 2 IV. Transient Levels of Concern a. ASAE Paper Number Graph. 3 b. Conservative Table of Interpreted Values of Reinemann s Graph... 3 c. Behavioral Response for 5% Most Sensitive Cows. 3 V. TEKSCOPE settings as suggested for Ag Rep Play-by-Play 6 Store a setting as USER 2 6 Overview of Steps 1. RESET to factory default 6 2. VERTICAL 7 3. HORIZOTAL 9 4. TRIGGER 10 MENUS 11 Save current setup 12 Recall current setup 13 Capturing a transient event 14 Display and Hold a transient on the Screen 14 Saving Waveform displayed on the Screen 15 Recall a Saved Waveform 16 Transferring a Waveform to computer from Tekscope using Waveform Manager 17 Auto Range 22
2 Voltage Introduction The Tekscope is a hand held digital oscilloscope. It is intended to be used to measure both the power line frequency and higher frequency components of steady state and transient voltages that may be present in the cow contact area. Definitions Waveform: The path traced by the voltage and plotted as a function of time. Instantaneous Value: The magnitude of the waveform a any instant in time. The magnitude is obtained from the vertical axis. This value can be obtained from interpreting it from the volts/div setting or use of the cursors function of the Tekscope. Periodic Waveform: A waveform that continually repeats itself in regular intervals. ie: 60Hz contribution in the cow contact area. Period (T): The time between regular intervals. Cycle: The portion of a waveform contained in one period. Frequency (f): The number of cycles in one second measured in Hertz (Hz). Figure mS/div 500mV/div One period (T) Time 1Hz (Hertz) = 1c/s (cycle per second) T = 1/f or f =1/T T = one period measured in seconds f = frequency measured in Hertz Example
3 2 One period at 60Hz 16.67ms 1/60Hz.01667s and 1/.01667s 60Hz Note: For a clean sine wave, the AC rms value of the waveform is the peak value divided by the square root of 2. In Figure 1 the maximum value (or peak value) of the waveform is 0.707V the ACrms value is 0.50V Scientific Notation Prefix Abbreviation Power of 10 Nano n = 10-9 Micro = 10-6 Milli m = 10-3 Kilo k 1000 = 10 3 Mega M = 10 6 Giga G =10 9 If one has a unit with a prefix and wishes to remove the prefix (ie: millisecond to seconds), multiply by the power of 10. To add a prefix to a unit (ie: volts to millivolts), divide by the power of 10. Examples 0.026V (volts).026 X mV (millivolts) 16.67ms (milliseconds) X s (seconds)
4 Voltage (Zero to Peak) 500 Ohm Cow Contact 3 TRANSIENT LEVELS OF CONCERN The following table is interpreted from ASAE Paper Number Effects of Frequency and Duration on the Sensitivity of Dairy Cows to Transient Voltages by Reinamann etal. Phase Duration 600 Hz = 835 sec 6,000 Hz = 83.5 sec 60,000 Hz = 8.35 sec Phase duration is the time between zero crossings Phase Duration Tp ( sec) Threshold Voltage* Vt (Peak V) Threshold Current It (Peak ma) < *Across 500 resistor 10,000 1,000 Behavioral response for 5% most sensitive cows, sine waves muzzle to hooves exposure Fencers 1 cycle Biphasic 1 cycle Monophasic Multi Cycle Phase Duration (microseconds) = time between zero crossings Reinemann (Reinemann 2002)
5 4 Overview of Steps Goal: Want to have a common setting that can be recalled by any ag rep for comparison to other reps measurements. Listed is an overview of what this setup will provide: This basic setup will provide a 20 second rolling view on the Tekscope. o The Tekscope will detect single pulses as low as 2 Microseconds but will not identify duration without changing the time on the horizontal axis. Triggering will not be needed for the 20 second view but will be needed when set at or below 200ms SEC/DIV on horizontal axis. If the capture of a specific event is desired, just decrease the Horizontal SEC/DIV to 200ms or less and use RUN/STOP button to reset trigger (no change of Acquire is necessary). TEKSCOPE settings as suggested for Ag Rep Italic is what you need to change SAVE/RECALL Step 1 Recall Factory Setup Step 2 OK Recall Setup Step 3 VERTICAL Changes below. If not listed, the factory setting is same. Display CH1 and turn all other waveforms off. MENU Coupling = AC Change from DC to AC Invert = Off Bandwidth = Full Position = 0 div Probe type = 1x Change from 10x to 1x with toggle Set VOLTS/DIV = 2V Change HORIZONTAL Set SEC/DIV to 2 S Change MENU Time Base = Main Trigger Position = 10% Change from 50% to 10% TRIGGER MENU Type = Edge Source = Ch 1 Coupling = DC Slope = positive Mode = Auto & Holdoff MENUS: ACQUIRE Mode = Pk Detect Change to Pk Detect Stop After Single Sequence Change to Stop After Single Sequence
6 5 MENUS: MEAS Select Measurement for Ch 1 Pk-Pk OK Select Measurement Change Change MENUS: SAVE/RECALL Step 1 Save Current Setup Step 2 To Setup 2 user Step 3 OK Save Group Step 4 TO RECALL this setting can be recalled by: SAVE/RECALL Recall Saved Setup Recall Setup 2 user If the capture of a specific event is desired, just decrease the Horizontal SEC/DIV to 200ms or less (no change of Acquire is necessary), and adjust the trigger level.
7 6 Play-by-Play Store a setting as user 2 Overview of Steps: Reset to factory default (If you want to save your own settings, save to user 3). Change settings to common set up for VERTICAL, HORIZONTAL, TRIGGER, and MENUS. Save settings so that setup can be recalled at any time. 1. RESET to factory default SAVE/RECALL Step 1 Recall Factory Setup Step 2 OK Recall Setup Step 3 TRIGGER LEVEL Pushing CLEAR MENU will clear the display of the settings being changed. Italic is what you need to change from the factory setting to set up user 2
8 7 2. VERTICAL- Changes below. If not listed, the factory setting is same. Set VOLTS/DIV = 2V Change Display CH1 and turn all other waveforms off. 3) CH1 on screen 2) Turn on CH1 1) Turn off WAVEFORM
9 MENU Coupling = AC Change from DC to AC Invert = Off Bandwidth = Full Position = 0 div Probe type = 1x Change from 10x to 1x with toggle 8
10 9 3. HORIZONTAL Set SEC/DIV to 2 S Change MENU Time Base = Main Trigger Position = 10%
11 10 4. TRIGGER MENU Type = Edge Source = Ch 1 Coupling = DC Slope = positive Mode = Auto & Holdoff Trigger level can be adjusted and appears as arrow on screen and a number in lower right corner of scope display.
12 11 MENUS ACQUIRE o Mode = Pk Detect Change to Pk Detect o Stop After Single Sequence Change to Stop After Single Sequence \
13 12 SAVE/RECALL o Save Current Setup o To Setup 2 user o OK Save Group Changes user #
14 13 TO RECALL this setting can be recalled by: SAVE/RECALL Recall Saved Setup Recall Setup 2 user Press RUN/STOP HOLD button to start scoll.
15 14 If the capture of a specific event is desired, just decrease the Horizontal SEC/DIV to 200ms or less (no change of Acquire is necessary), and adjust the trigger level. Display and Hold a transient on the Screen TRIGGER Set the TRIGGER LEVEL (the arrow on the right side of the screen) slightly above or below the steady state waveform. MENU Type = Edge Source = Ch 1 Coupling = DC Slope = positive Mode = Auto & Holdoff MENUS: ACQUIRE Mode = Pk Detect Stop After = Single Sequence Previously set Press the HOLD button until RUN: appears in the Status Line. When the input voltage exceeds the trigger level a new waveform will appear on the display, and Hold: will appear in the Status Line. Repeat this procedure until an acceptable waveform is obtained.
16 15 Save Waveform Displayed on the Screen MENU: SAVE/RECALL Save Ch 1 = (an open waveform memory location 1-10; use +/- to change the memory location). Note the Location, Date, and Time when waveform was captured. OK Save Waveform, OK Overwrite Waveform (if want to do this) Waveform is captured as shown below: Save CH 1 Pick # of waveform saved Toggle # using TOGGLE switch OK overwrite waveform WAVEFORM OFF button will clear screen
17 16 Recall a Saved Waveform MENU: SAVE/RECALL Recall Saved Waveform = (From Wfm 1-10; use =/- to change the memory location). Note: Waveforms stored from CH 1 are recalled with REF A, and waveforms stored from CH 2 are recalled with REF B. OK Recall Waveform
18 17 Transferring a Waveform to computer from Tekscope using Waveform Manager Start Waveform Manager Open New Document under File
19 18 Choose TRANSFER WAVEFORMS Edit, then Waveform Window Properties (Ctrl+E)
20 19 Delete {WfmLbl} - {DateStamp /d} and type in Farmname Date Time of Capture Location File title appears Transfer Waveform from Scope
21 20 Tranfer Waveform that you have displayed Waveform is tranfered
22 File, Save Document As. Browse to find folder to save in, name file, and save. 21
23 AUTO RANGE This button will allow the Scope to automatically pick the VERTICAL and HORIZONTAL voltage and time settings. 22
ECE65 Introduction to the Function Generator and the Oscilloscope Created by: Eldridge Alcantara (Spring 2007)
ECE65 Introduction to the Function Generator and the Oscilloscope Created by: Eldridge Alcantara (Spring 2007) I. Getting Started with the Function Generator OUTPUT Red Clip Small Black Clip 1) Turn on
More informationUniversity of California, San Diego Department of Electrical and Computer Engineering
University of California, San Diego Department of Electrical and Computer Engineering Part One: Introduction of Lab TAs ECE65, Spring 2007 Lab 0, ECE 65 Lab Orientation 1) James Liao, geniojames@yahoo.com
More informationThe newer Fluke 199C recording scope meters are GREAT instruments if used properly.
CowContacttm Volume 2004 Issue I March 2004 www.phasorlabs.com If you use FLUKE ScopeMeters and FlukeView logging software..see CowContact Volume 2G. If you use the Fluke 199C read this FLUKE ScopeMeters
More informationOscilloscope Operation. Visualizing Signals and Making Measurements
Oscilloscope Operation Visualizing Signals and Making Measurements Set Up Oscilloscope Start with the oscilloscope off, with the input plugged into channel one. Press the power button to turn the scope
More informationFaculty of Engineering, Thammasat University
Faculty of Engineering, Thammasat University Experiment 6: Oscilloscope (For room 506) Objectives: 1. To familiarize you with the Oscilloscope and Function Generator User Manual: Oscilloscope 1 5 9 4 7
More information2 Oscilloscope Familiarization
Lab 2 Oscilloscope Familiarization What You Need To Know: Voltages and currents in an electronic circuit as in a CD player, mobile phone or TV set vary in time. Throughout the course you will investigate
More informationEvaluating Electrical Events on the Dairy Farm
Evaluating Electrical Events on the Dairy Farm What if we had a way to evaluate all the different measurements people make on a dairy farm and we could put this information into a form that the average
More informationMeasuring Stray Voltage. Steady state
Measuring Stray Voltage What to measure: >Steady state >Motor starting transients >Impulses September 2000 cforster@forstereng.com 1 Steady state Where to measure: >All known cow contact points >Stanchions
More informationEENG-201 Experiment # 4: Function Generator, Oscilloscope
EENG-201 Experiment # 4: Function Generator, Oscilloscope I. Objectives Upon completion of this experiment, the student should be able to 1. To become familiar with the use of a function generator. 2.
More informationEXPERIMENT NUMBER 2 BASIC OSCILLOSCOPE OPERATIONS
1 EXPERIMENT NUMBER 2 BASIC OSCILLOSCOPE OPERATIONS The oscilloscope is the most versatile and most important tool in this lab and is probably the best tool an electrical engineer uses. This outline guides
More informationI. Introduction to Animal Sensitivity and Response
Stray Voltage Field Guide Douglas J. Reinemann, Ph.D. Professor of Biological Systems Engineering University of Wisconsin Madison September 2007 Update I. Introduction to Animal Sensitivity and Response
More informationNotes on Experiment #1
Notes on Experiment #1 Bring graph paper (cm cm is best) From this week on, be sure to print a copy of each experiment and bring it with you to lab. There will not be any experiment copies available in
More informationPHYSICS 171 UNIVERSITY PHYSICS LAB II. Experiment 4. Alternating Current Measurement
PHYSICS 171 UNIVERSITY PHYSICS LAB II Experiment 4 Alternating Current Measurement Equipment: Supplies: Oscilloscope, Function Generator. Filament Transformer. A sine wave A.C. signal has three basic properties:
More informationThe Oscilloscope. Vision is the art of seeing things invisible. J. Swift ( ) OBJECTIVE To learn to operate a digital oscilloscope.
The Oscilloscope Vision is the art of seeing things invisible. J. Swift (1667-1745) OBJECTIVE To learn to operate a digital oscilloscope. THEORY The oscilloscope, or scope for short, is a device for drawing
More informationP a g e 1 ST985. TDR Cable Analyzer Instruction Manual. Analog Arts Inc.
P a g e 1 ST985 TDR Cable Analyzer Instruction Manual Analog Arts Inc. www.analogarts.com P a g e 2 Contents Software Installation... 4 Specifications... 4 Handling Precautions... 4 Operation Instruction...
More informationTime-Varying Signals
Time-Varying Signals Objective This lab gives a practical introduction to signals that varies with time using the components such as: 1. Arbitrary Function Generator 2. Oscilloscopes The grounding issues
More informationGetting Started. MSO/DPO Series Oscilloscopes. Basic Concepts
Getting Started MSO/DPO Series Oscilloscopes Basic Concepts 001-1523-00 Getting Started 1.1 Getting Started What is an oscilloscope? An oscilloscope is a device that draws a graph of an electrical signal.
More information2 : AC signals, the signal generator and the Oscilloscope
2 : AC signals, the signal generator and the Oscilloscope Expected outcomes After conducting this practical, the student should be able to do the following Set up a signal generator to provide a specific
More informationAppendix A: Specifications
All specifications apply to the TDS 200-Series Digital Oscilloscopes and a P2100 probe with the Attenuation switch set to 10X unless noted otherwise. To meet specifications, two conditions must first be
More informationExperiment #2: Introduction to Lab Equipment: Function Generator, Oscilloscope, and Multisim
SCHOOL OF ENGINEERING AND APPLIED SCIENCE DEPARTMENT OF ELECTRICAL AND COMPUTER ENGINEERING ECE 2110: CIRCUIT THEORY LABORATORY Experiment #2: Introduction to Lab Equipment: Function Generator, Oscilloscope,
More informationExperiment # 1 Introduction to Lab Equipment
Experiment # 1 Introduction to Lab Equipment 1. Synopsis: In this introductory lab, we will review the basic concepts of digital logic design and learn how to use the equipment available in the laboratory.
More informationME 365 EXPERIMENT 1 FAMILIARIZATION WITH COMMONLY USED INSTRUMENTATION
Objectives: ME 365 EXPERIMENT 1 FAMILIARIZATION WITH COMMONLY USED INSTRUMENTATION The primary goal of this laboratory is to study the operation and limitations of several commonly used pieces of instrumentation:
More informationUNIVERSITY OF CALIFORNIA, SANTA BARBARA Department of Electrical and Computer Engineering. ECE 2A & 2B Laboratory Equipment Information
UNIVERSITY OF CALIFORNIA, SANTA BARBARA Department of Electrical and Computer Engineering ECE 2A & 2B Laboratory Equipment Information Table of Contents Digital Multi-Meter (DMM)... 1 Features... 1 Using
More information54645D. Mixed Signal Oscilloscope
54645D Mixed Signal Oscilloscope Page 1 of 42 Instructions for the use of the 54645D Mixed Signal Oscilloscope This pamphlet is intended to give you (the student) an overview on the use of the 54645D Mixed
More informationOscilloscope Applications MREC Rural Energy Conference 2012 Prepared by Paul Ortmann, P.E. /
MREC Rural Energy Conference 2012 Prepared by Paul Ortmann, P.E. / portmann@idahopower.com Introduction An oscilloscope can help the user get more detailed electrical measurements than can be obtained
More informationEC310 Security Exercise 20
EC310 Security Exercise 20 Introduction to Sinusoidal Signals This lab demonstrates a sinusoidal signal as described in class. In this lab you will identify the different waveform parameters for a pure
More informationVoltage (measured on the vertical axis)
Operate a Digital Storage Oscilloscope Name(s) It is important to understand these basic features of the oscilloscope. VOLTAGE measured on the vertical axis. TIME measured on the horizontal axis. TRIGGER
More informationN acquisitions, all channels simultaneously, N is selectable from 4, 16, 64, and 128 Inputs
With compliments All specifications apply to the TDS 200-Series Digital Real-Time Oscilloscope with a P2100 probe with the Attenuation switch set to 10X unless noted otherwise. To meet specifications,
More informationCombinational logic: Breadboard adders
! ENEE 245: Digital Circuits & Systems Lab Lab 1 Combinational logic: Breadboard adders ENEE 245: Digital Circuits and Systems Laboratory Lab 1 Objectives The objectives of this laboratory are the following:
More informationSpecifications for DS1000CA Series
Revised December, 2009 RIGOL Specifications for DS1000CA Series All specifications apply to the DS1000CA Series Oscilloscopes unless noted otherwise. To meet these specifications, two conditions must first
More informationLaboratory 1 Generating and viewing signals rev. 20e. Oscilloscope Settings
1 2 Laboratory 1 Generating and viewing signals rev. 20e Purpose: Familiarization with the basic functions of an oscilloscope and of a signal generator. Adjusting and measuring specific parameters of signals.
More informationWaveform Generators and Oscilloscopes. Lab 6
Waveform Generators and Oscilloscopes Lab 6 1 Equipment List WFG TEK DPO 4032A (or MDO3012) Resistors: 10kΩ, 1kΩ Capacitors: 0.01uF 2 Waveform Generators (WFG) The WFG supplies a variety of timevarying
More informationtotal j = BA, [1] = j [2] total
Name: S.N.: Experiment 2 INDUCTANCE AND LR CIRCUITS SECTION: PARTNER: DATE: Objectives Estimate the inductance of the solenoid used for this experiment from the formula for a very long, thin, tightly wound
More information332:223 Principles of Electrical Engineering I Laboratory Experiment #2 Title: Function Generators and Oscilloscopes Suggested Equipment:
RUTGERS UNIVERSITY The State University of New Jersey School of Engineering Department Of Electrical and Computer Engineering 332:223 Principles of Electrical Engineering I Laboratory Experiment #2 Title:
More informationEE EXPERIMENT 1 (2 DAYS) BASIC OSCILLOSCOPE OPERATIONS INTRODUCTION DAY 1
EE 2101 - EXPERIMENT 1 (2 DAYS) BASIC OSCILLOSCOPE OPERATIONS INTRODUCTION The oscilloscope is the most versatile and most important tool in this lab and is probably the best tool an electrical engineer
More informationAgilent 33522A Function Arbitrary Waveform Generator. Tektronix TDS 3012B Oscilloscope
Agilent 33522A Function/Arbitrary Waveform Generator and Tektronix TDS 3012B Oscilloscope Agilent 33522A Function Arbitrary Waveform Generator The signal source for this lab is the Agilent 33522A Function
More informationChapter 5 : Specifications
Chapter 5 : Specifications All specifications apply to the DS1000B Series Oscilloscopes and a probe with the Attenuation switch set to 10X unless noted otherwise. To meet these specifications, two conditions
More informationUser Manual RIGOL. DS1000 Series Digital Oscilloscopes DS1000CD, DS1000C, DS1000MD, DS1000M. Publication number DS March 2006
User Manual RIGOL Publication number DS1-061107 March 2006 DS1000 Series Digital Oscilloscopes DS1000CD, DS1000C, DS1000MD, DS1000M Copyright RIGOL Technologies, Inc. 2006 All Rights Reserved Copyright
More informationLab 1 - Analogue and Digital Signals
Lab 1 - Analogue and Digital Signals Objective 1. To reintroduce the equipment used in the lab. 2. To get practical experience assembling and analyzing circuits. 3. To examine physical analogue and digital
More informationHantek. Hantek Electronic co.,ltd. No.177 zhuzhou road(huite industry city), QingDao,China
Hantek Hantek Electronic co.,ltd. No.177 zhuzhou road(huite industry city), QingDao,China DSO1000SERIES HANDHELD OSCILLOSCOPE USER S MANUAL 1060/1200/1600/1600H www.hantek.com.cn DSO1000 SERIES HANDHELD
More informationUser s Guide RIGOL. DS1000E, DS1000D Series Digital Oscilloscopes DS1102E, DS1052E, DS1102D, DS1052D. Publication number UGA July 2008
User s Guide RIGOL Publication number UGA07107-1110 July 2008 DS1000E, DS1000D Series Digital Oscilloscopes DS1102E, DS1052E, DS1102D, DS1052D All Rights Reserved All Rights Reserved RIGOL products are
More informationDSO5000P Series Digital Storage Oscilloscope User Manual. (Version 1.1)
DSO5000P Series Digital Storage Oscilloscope User Manual (Version 1.1) Contents Contents Contents... i Chapter 1 Safety Tips... 1 1.1 General Safety Summary... 1 1.2 Safety Terms and Symbols... 2 1.3 Terms
More informationRIGOL Data Sheet. DS1000E, DS1000D Series Digital Oscilloscopes DS1102E, DS1052E, DS1102D, DS1052D. Product Overview. Easy to Use Design.
RIGOL Data Sheet DS1000E, DS1000D Series Digital Oscilloscopes DS1102E, DS1052E, DS1102D, DS1052D Product Overview The DS1000E, DS1000D series instruments are economical, high-performance digital oscilloscopes.
More informationUser s Guide RIGOL. DS1000E, DS1000D Series Digital Oscilloscopes DS1102E, DS1052E, DS1102D, DS1052D. Publication number UGA July 2009
User s Guide RIGOL Publication number UGA07111-1110 July 2009 DS1000E, DS1000D Series Digital Oscilloscopes DS1102E, DS1052E, DS1102D, DS1052D All Rights Reserved 1. All Rights Reserved 2. RIGOL products
More informationUser s Guide RIGOL. DS1000CA Series Digital Oscilloscopes DS1302CA, DS1202CA, DS1102CA, DS1062CA. Publication number DS1000CA April 2008
User s Guide RIGOL Publication number DS1000CA-080512 April 2008 DS1000CA Series Digital Oscilloscopes DS1302CA, DS1202CA, DS1102CA, DS1062CA Copyright 1998-2008 RIGOL Technologies, Inc. All Rights Reserved
More informationTest 1: What is the effect on cattle drinking water from an insulated water trough if an electric fence is within inches of the water tank?
CowContacttm Volume 2004 Issue J March 2004 www.phasorlabs.com In recent agricultural articles it was proposed that tests done at a cattle watering tank proved that cows were able to detect voltages much
More informationLABORATORY 4. Palomar College ENGR210 Spring 2017 ASSIGNED: 3/21/17
LABORATORY 4 ASSIGNED: 3/21/17 OBJECTIVE: The purpose of this lab is to evaluate the transient and steady-state circuit response of first order and second order circuits. MINIMUM EQUIPMENT LIST: You will
More informationFluke199XRAY. Users Manual. Medical ScopeMeter
Fluke199XRAY Medical ScopeMeter Users Manual 4822 872 30791 August 2006 2006 Fluke Corporation, All rights reserved. All product names are trademarks of their respective companies. Table of Contents Title
More informationUser Manual RIGOL. DS1000KCA Series Digital Oscilloscopes DS1302CA, DS1202CA, DS1102CA, DS1062CA. Publication number DS1KCA June 2007
User Manual RIGOL Publication number DS1KCA-070712 June 2007 DS1000KCA Series Digital Oscilloscopes DS1302CA, DS1202CA, DS1102CA, DS1062CA Copyright RIGOL Technologies, Inc. 2007 All Rights Reserved Copyright
More informationThis section describes the basic operation including start-up. See Section 2, Explanation of Functions for details.
1 Section 1 Basic Operation This section describes the basic operation including start-up. See Section 2, Explanation of Functions for details. 2 Appearance ƒ Front View Power switch Input terminal ƒ External
More informationLab #2 First Order RC Circuits Week of 27 January 2015
ECE214: Electrical Circuits Laboratory Lab #2 First Order RC Circuits Week of 27 January 2015 1 Introduction In this lab you will investigate the magnitude and phase shift that occurs in an RC circuit
More informationIntroduction to Oscilloscopes Instructor s Guide
Introduction to Oscilloscopes A collection of lab exercises to introduce you to the basic controls of a digital oscilloscope in order to make common electronic measurements. Revision 1.0 Page 1 of 25 Copyright
More informationName EET 1131 Lab #2 Oscilloscope and Multisim
Name EET 1131 Lab #2 Oscilloscope and Multisim Section 1. Oscilloscope Introduction Equipment and Components Safety glasses Logic probe ETS-7000 Digital-Analog Training System Fluke 45 Digital Multimeter
More informationExperiment 5 The Oscilloscope
Experiment 5 The Oscilloscope Vision is the art of seeing things invisible. J. Swift (1667-1745) OBJECTIVE To learn to operate a cathode ray oscilloscope. THEORY The oscilloscope, or scope for short, is
More informationDoing It Right. Phasor Labs. March voice fax
Doing It Right Phasor Labs 5420 Glenway Circle Oregon, Wisconsin 53575 608-835-9605 voice 608-835-9039 fax cforster@phasorlabs.com March 2004 cforster@phasorlabs.com 1 Doing It Right March 2004 cforster@phasorlabs.com
More informationEE 201 Function / Arbitrary Waveform Generator and Oscilloscope Tutorial
EE 201 Function / Arbitrary Waveform Generator and Oscilloscope Tutorial 1 This is a programmed learning instruction manual. It is written for the Agilent DSO3202A Digital Storage Oscilloscope. The prerequisite
More informationDSO1000E/F Series Digital Storage Oscilloscope User Manual. (Version 1.3)
DSO1000E/F Series Digital Storage Oscilloscope User Manual (Version 1.3) Copyright Declaration All rights reserved; no part of this document may be reproduced or transmitted in any form or by any means,
More informationUser s Guide RIGOL. DS1000CA Series Digital Oscilloscopes DS1302CA, DS1202CA, DS1102CA, DS1062CA. Publication number UGA Oct.
User s Guide RIGOL Publication number UGA03106-1110 Oct. 2008 DS1000CA Series Digital Oscilloscopes DS1302CA, DS1202CA, DS1102CA, DS1062CA 2007 RIGOL Technologies, Inc. All Rights Reserved. 2007 RIGOL
More informationDSO4000BC Series Digital Storage Oscilloscope User Manual
DSO4000BC Series Digital Storage Oscilloscope User Manual (V1.3) Copyright Declaration All rights reserved; no part of this document may be reproduced or transmitted in any form or by any means, electronic
More informationOscilloscope and Function Generators
MEHRAN UNIVERSITY OF ENGINEERING AND TECHNOLOGY, JAMSHORO DEPARTMENT OF ELECTRONIC ENGINEERING ELECTRONIC WORKSHOP # 02 Oscilloscope and Function Generators Roll. No: Checked by: Date: Grade: Object: To
More informationUCE-DSO210 DIGITAL OSCILLOSCOPE USER MANUAL. FATIH GENÇ UCORE ELECTRONICS REV1
UCE-DSO210 DIGITAL OSCILLOSCOPE USER MANUAL FATIH GENÇ UCORE ELECTRONICS www.ucore-electronics.com 2017 - REV1 Contents 1. Introduction... 2 2. Turn on or turn off... 3 3. Oscilloscope Mode... 3 3.1. Display
More informationDS1000B Series Digital Oscilloscopes
Product Overview DS1000B series oscilloscopes are designed with four analog channels and 1 external trigger channel, which can capture multi-channel signal simultaneously and meet industrial needs. The
More informationThe University of Jordan Mechatronics Engineering Department Electronics Lab.( ) Experiment 1: Lab Equipment Familiarization
The University of Jordan Mechatronics Engineering Department Electronics Lab.(0908322) Experiment 1: Lab Equipment Familiarization Objectives To be familiar with the main blocks of the oscilloscope and
More informationMSO-5000B Mixed Storage Oscilloscope User Manual
MSO-5000B Mixed Storage Oscilloscope User Manual Contents Contents CONTENTS... I COPYRIGHT DECLARATION... IV CHAPTER 1 SAFETY TIPS... 1 1.1 GENERAL SAFETY SUMMARY... 1 1.2 SAFETY TERMS AND SYMBOLS... 2
More informationDST Series B Type Digital Storage Oscilloscope User Manual
DST Series B Type Digital Storage Oscilloscope User Manual Contents Contents Contents... i Copyright Declaration... iv Chapter 1 Safety Tips... 1 1.1 General Safety Summary... 1 1.2 Safety Terms and Symbols...
More informationUCE-DSO212 DIGITAL OSCILLOSCOPE USER MANUAL. UCORE ELECTRONICS
UCE-DSO212 DIGITAL OSCILLOSCOPE USER MANUAL UCORE ELECTRONICS www.ucore-electronics.com 2017 Contents 1. Introduction... 2 2. Turn on or turn off... 3 3. Oscilloscope Mode... 4 3.1. Display Description...
More informationDS1102E, DS1052E, DS1102D, DS1052D
RIGOL Data Sheet DS1000E, DS1000D Series Digital Oscilloscopes DS1102E, DS1052E, DS1102D, DS1052D Product Overview DS1000E, DS1000D series are kinds of economical digital oscilloscope with high-performance.
More informationB. Equipment. Advanced Lab
Advanced Lab Measuring Periodic Signals Using a Digital Oscilloscope A. Introduction and Background We will use a digital oscilloscope to characterize several different periodic voltage signals. We will
More informationET 304A Laboratory Tutorial-Circuitmaker For Transient and Frequency Analysis
ET 304A Laboratory Tutorial-Circuitmaker For Transient and Frequency Analysis All circuit simulation packages that use the Pspice engine allow users to do complex analysis that were once impossible to
More informationLab 0: Introduction to basic laboratory instruments. Revised by Dan Hoang & Tai-Chang Chen 03/30/2009
Lab 0: Introduction to basic laboratory instruments Revised by Dan Hoang & Tai-Chang Chen 03/30/2009 1. Objectives 1. To learn safety procedures in the laboratory. 2. To learn how to use basic laboratory
More informationIntroduction to basic laboratory instruments
BEE 233 Laboratory-1 Introduction to basic laboratory instruments 1. Objectives To learn safety procedures in the laboratory. To learn how to use basic laboratory instruments: power supply, function generator,
More informationIntroduction to Basic Laboratory Instruments
Introduction to Contents: 1. Objectives... 2 2. Laboratory Safety... 2 3.... 2 4. Using a DC Power Supply... 2 5. Using a Function Generator... 3 5.1 Turn on the Instrument... 3 5.2 Setting Signal Type...
More informationUser s Guide RIGOL. DS1000B Series Digital Oscilloscopes DS1062/4B,DS1102/4B,DS1202/4B. Publication number UGA July 2008
User s Guide RIGOL Publication number UGA04107-1210 July 2008 DS1000B Series Digital Oscilloscopes DS1062/4B,DS1102/4B,DS1202/4B All Rights Reserved All Rights Reserved. RIGOL products are protected by
More informationData Sheet. Digital Storage Oscilloscope. Features & Benefits. Applications. Ease-of-Use Feature DSO5202BMT DSO5102BMT DSO5062BMT
Data Sheet Digital Storage Oscilloscope DSO5202BMT DSO5102BMT DSO5062BMT Features & Benefits 200/100/60MHz Bandwidths 1GSa/s Real Time Sample Rate 2M Memory Depth Trigger mode: Edge, Pulse Width, Video,
More informationVirtual Lab 1: Introduction to Instrumentation
Virtual Lab 1: Introduction to Instrumentation By: Steve Badelt and Daniel D. Stancil Department of Electrical and Computer Engineering Carnegie Mellon University Pittsburgh, PA Purpose: Measurements and
More informationExperiment 9 The Oscilloscope and Function Generator
Experiment 9 The Oscilloscope and Function Generator Introduction The oscilloscope is one of the most important electronic instruments available for making circuit measurements. It displays a curve plot
More informationIntroduction to oscilloscope. and time dependent circuits
Physics 9 Intro to oscilloscope, v.1.0 p. 1 NAME: SECTION DAY/TIME: TA: LAB PARTNER: Introduction to oscilloscope and time dependent circuits Introduction In this lab, you ll learn the basics of how to
More informationPh 3455 The Franck-Hertz Experiment
Ph 3455 The Franck-Hertz Experiment Required background reading Tipler, Llewellyn, section 4-5 Prelab Questions 1. In this experiment, we will be using neon rather than mercury as described in the textbook.
More informationAutomotive Scope/GMM/OBD II Code Reader
Finest 1006 Automotive Scope/GMM/OBD II Code Reader Automotive On-board diagnostic systems of thesedays have gone a long way toward helping you locate a problem. But those systems aren't perfect and they
More informationMASSACHUSETTS INSTITUTE OF TECHNOLOGY /6.071 Introduction to Electronics, Signals and Measurement Spring 2006
MASSACHUSETTS INSTITUTE OF TECHNOLOGY.071/6.071 Introduction to Electronics, Signals and Measurement Spring 006 Lab. Introduction to signals. Goals for this Lab: Further explore the lab hardware. The oscilloscope
More informationLAB I. INTRODUCTION TO LAB EQUIPMENT
LAB I. INTRODUCTION TO LAB EQUIPMENT 1. OBJECTIVE In this lab you will learn how to properly operate the basic bench equipment used for characterizing active devices: 1. Oscilloscope (Keysight DSOX 1102A),
More informationRIGOL Data Sheet. DS1000E, DS1000D Series Digital Oscilloscopes DS1102E, DS1052E, DS1102D, DS1052D. Product Overview. Applications. Easy to Use Design
RIGOL Data Sheet DS1000E, DS1000D Series Digital Oscilloscopes DS1102E, DS1052E, DS1102D, DS1052D Product Overview DS1000E, DS1000D series are kinds of economical digital oscilloscope with high-performance.
More informationMeasurement Bench. Accessories. Power supply. Wave form generator. Multimetre. Oscilloscope. Dr. L.Scucchia
Measurement Bench Accessories Power supply Wave form generator Multimetre Oscilloscope OSCILLOSCOPE Oscilloscope (1) The oscilloscope allows to display a voltage (vertical axis - Y axis) versus time (horizontal
More informationUniversity of Utah Electrical & Computer Engineering Department ECE 2210/2200 Lab 4 Oscilloscope
University of Utah Electrical & Computer Engineering Department ECE 2210/2200 Lab 4 Oscilloscope Objectives 1 Introduce the Oscilloscope and learn some uses. 2 Observe Audio signals. 3 Introduce the Signal
More informationEECS 318 Electronics Lab Laboratory #2 Electronic Test Equipment
EECS 318 Electronics Lab Laboratory #2 Electronic Test Equipment Objectives: The purpose of this laboratory is to acquaint you with the electronic sources and measuring equipment you will be using throughout
More informationA semester of Experiments for ECE 225
A semester of Experiments for ECE 225 Contents General Lab Instructions... 3 Notes on Experiment #1... 4 ECE 225 Experiment #1 Introduction to the function generator and the oscilloscope... 5 Notes on
More informationLab: INTRODUCTION TO THE WAVEFORM GENERATOR AND THE OSCILLOSCOPE
Name EET101/Lab#5; EET121/Lab#5; EGR104/Lab#3 Sec / Night Date Lab Partner(s) Name(s) Lab: INTRODUCTION TO THE WAVEFORM GENERATOR AND THE OSCILLOSCOPE Objectives: Each student will: 1. Know the function
More informationAgilent 3000 Series Oscilloscopes
Agilent 3000 Series Oscilloscopes User s and Service Guide Agilent Technologies In This Book This book gives you the information you need to begin using the 3000 Series Oscilloscopes. It contains the following
More informationExercise 4 - THE OSCILLOSCOPE
Exercise 4 - THE OSCILLOSCOPE INTRODUCTION You have been exposed to analogue oscilloscopes in the first year lab. As you are probably aware, the complexity of the instruments, along with their importance
More informationHands-On Digital Communication Episode 2: SystemVue Basics and Simulation of a Crystal Radio
Hands-On Digital Communication Episode 2: SystemVue Basics and Simulation of a Crystal Radio By Dennis Silage, K3DS k3ds@arrl.net A hands-on computer simulation of digital communication geared toward Amateur
More informationLAB I. INTRODUCTION TO LAB EQUIPMENT
1. OBJECTIVE LAB I. INTRODUCTION TO LAB EQUIPMENT In this lab you will learn how to properly operate the oscilloscope Agilent MSO6032A, the Keithley Source Measure Unit (SMU) 2430, the function generator
More informationWhy Modern Servicing Requires Complete Waveform & Circuit Analyzing!
Why Modern Servicing Requires Complete Waveform & Circuit Analyzing! DC Bias Voltages DC Currents Resistance AC Signals Of Various Waveshapes & Amplitudes Continuity Of Circuit Paths & Components If you
More informationDSO4000 Series Digital Storage Oscilloscope User Manual. (Version 1.3)
DSO4000 Series Digital Storage Oscilloscope User Manual (Version 1.3) Contents Contents... i Safety Tips... 1 General Safety Summary... 1 Safety Terms and Symbols... 2 Product Scrapping... 2 Brief Introduction
More informationSAMPLE: EXPERIMENT 2 Series RLC Circuit / Bode Plot
SAMPLE: EXPERIMENT 2 Series RLC Circuit / Bode Plot ---------------------------------------------------------------------------------------------------- This experiment is an excerpt from: Electric Experiments
More informationUser Manual Series. Digital Storage Oscilloscope 6810, 6806, March Copyright Protek Test & Measurement 2005 All Rights Reserved
User Manual March 2005 6800 Series Digital Storage Oscilloscope 6810, 6806, 6804 Copyright Protek Test & Measurement 2005 All Rights Reserved Copyright Protek Test & Measurement 2005 All Rights Reserved.
More informationDSO8000E SERIES HANDHELD OSCILLOSCOPE
DSO8000E SERIES HANDHELD OSCILLOSCOPE USER S MANUAL 8072E/8102E/8152E/8202E (V1.0.1) Contents Contents Contents... i Copyright Declaration... iii Chapter 1 Safety Tips... 1 1.1 General Safety Summary...
More informationLab #5 Steady State Power Analysis
Lab #5 Steady State Power Analysis Steady state power analysis refers to the power analysis of circuits that have one or more sinusoid stimuli. This lab covers the concepts of RMS voltage, maximum power
More informationHow to Setup a Real-time Oscilloscope to Measure Jitter
TECHNICAL NOTE How to Setup a Real-time Oscilloscope to Measure Jitter by Gary Giust, PhD NOTE-3, Version 1 (February 16, 2016) Table of Contents Table of Contents... 1 Introduction... 2 Step 1 - Initialize
More informationI. Introduction to Animal Sensitivity and Response
I. Introduction to Animal Sensitivity and Response The term stray voltage has been used to describe a special case of voltage developed on the grounded neutral system of a farm. If this voltage reaches
More informationUSE OF BASIC ELECTRONIC MEASURING INSTRUMENTS Part II, & ANALYSIS OF MEASUREMENT ERROR 1
EE 241 Experiment #3: USE OF BASIC ELECTRONIC MEASURING INSTRUMENTS Part II, & ANALYSIS OF MEASUREMENT ERROR 1 PURPOSE: To become familiar with additional the instruments in the laboratory. To become aware
More information