KS0107B 64CH COMMON DRIVER FOR DOT MATRIX LCD INTRODUCTION
|
|
- Bernice Newman
- 5 years ago
- Views:
Transcription
1 INTRODUCTION The is a LCD driver LSI with 64 channel output for dot matrix liquid crystal graphic display system. This device provides 64 shift register and 64 output driver. It generates the timing signal to control the KS0108B segment driver. The is fabricated by low power COS high voltage process technology and compose of the liquid crystal display system in combination with the KS0108B segment driver. 100 QFP-1420 FEATURES Dot matrix LCD common driver with 64 channel output. 64 bits shift register ot internal LCD driver circuit. Internal timing generator circuit for dynamic display. Selectable master/slave mode. Applicable LCD duty: 1/48, 1/64,1/96,1/128 Power supply voltage: + 5V ±10% LCD driving voltage: 8V~17V(-) Interface COON Driver SEGENT controller Other KS0108B PU High voltage COS process. 100QFP and bare chip available.
2 BLOCK DIAGRA C1C2C3 C62 C63 C64 L L L L 64 bits LCD driver R R R R 64 bits bidirection shift register DIO1 P SHL Data shift direction ƒ Phase selection control circuit DIO2 C R CR OSC Timing generator cirecuit FR V SS DS 1 DS 2 S FS Fig. 1. Functional block diagram
3 PIN CONFIGURATION C42 C41 C40 C39 C38 C37 C36 C35 C34 C33 C32 C31 C30 C29 C28 C27 C26 C25 C24 C C 22 C 21 C 20 C 19 C 18 C 17 C 16 C 15 C 14 C 13 C 12 C 11 C 10 C 9 C 8 C 7 C 6 C 5 C 4 C 3 C 2 C 1 L L L L DIO1 FS C 43 C 44 C 45 C 46 C 47 C 48 C 49 C 50 C 51 C 52 C 53 C 54 C 55 C 56 C 57 C 58 C 59 C 60 C 61 C 62 C 63 C 64 R R R V OR DIO2 P FR S V SS SHL CR R C DS2 DS1 Fig QFP Top View
4 PIN DESCRIPTION PIN(NO) SYBOL INPUT/OUTPUT DESCRIPTION ,58 V SS Power For internal logic circuit (+5V±10%) GND (0V) For LCD driver circuit 27, 54 24, 57 25, 56 26, 55 L, R L, R L, R L, R Power Bias supply voltage terminals to drive LCD. Select Level L(R), L(R) Non-Select Level L(R), L(R) L and R is connected by the same voltage. 42 S Input Selection of master/slave mode i) aster mode (S=1) DIO1, DIO2, and is output state. ii) Slave mode (S=0) SHL=1 DIO1 is input state(dio2 is output state) SHL=0 DIO2 is input state(dio1 is output state) and is input state. 39 SHL Input Selction of data shift direction. SHL H L Data shift direction DIO1 C1... C64 DIO2 DIO2 C64... C1 DIO1 49 P Input Selection of shift clock () phase. P H L shift clock() phase data shift at the rising edge of data shift at the falling edge of 30 FS Input Selection of oscillation frequency. i) aster mode When the freme frequency is 70Hz, the oscillation frequency should be fosc=430khz at FS=1 () fosc=215khz at FS=0 (V SS) ii) Slave mode Connect to DS1, DS2 Input Selectiom of display duty. i) aster mode DS1 DS2 Duty L L 1/48 L H 1/64 H L 1/96 H H 1/128 ii) Slave mode : Connect to.
5 PIN DESCRIPTION (continued) PIN(NO) SYBOL INPUT/OUTPUT DESCRIPTION C R RC Oscillator i) aster mode 37 CR KS0107 KS0107 R CR C R CR C R f C f ii) Slave mode open external clock open R CR C open Oopen PEN 44, 43, Output Operating clock output for the KS0108B i) aster mod Connection to and of the KS0108B ii) Slave mode Open 46 FR Output Synchronous frame signal. i) aster mode Connection to FR of the KS0108B ii) Slave mode Open 47 Input/Output Alternating signal input for LCD driving. i) aster mode: output state Connection to of the KS0108B ii) Slave mode: input state Connection to the controller 52 Input/Output Data shift clock i) aster mode: output state Connection to CL of the KS0108B ii) Slave mode: input state Connection to shift clock terminal of the controller. 29 DIO1 Input/Output Data input/output pin of internal shift register. 50 DIO2 S SHL DIO1 DIO2 H H Output Output L Output Output L H Input Output L Output Input 22~1 100~59 C1~C64 Output Common signal output for LCD driving. DATA OUT L L V 1 L H V 4 H L V 5 H H V 0 34,36,38,41 45,48,51,53 No Connection
6 AXIU ABSOLUTE LIIT Characteristic Symbol Value Unit Note Operating Voltage -0.3~+7.0 V *1 Supply Voltage -19.0~+0.3 V *4 Driver Supply Voltage V B -0.3~+0.3 V *1,2 V LCD -0.3~+0.3 V *3,4 Operating Temperature T OPR -30~+85 C - Storage Temperature T STG -55~+125 C - *1. Based on V SS=0V *2. Applies to input terminals and I/O terminals at high impedance. (Except L(R), L(R), L(R) and L(R)) *3. Applies to L(R), L(R), L(R) and L(R). *4. Voltgae level: L=R L=R L=R L=R. ELECTRICAL CHARACTERISTICS DC Characteristics (=+5V ± 10%, V SS=0V,l - l =8~17V, T a=-30 ~ +85 C) Characteristic Symbol condition in Typ ax Unit Note Input High V IH V *1 Voltage Low V IL V SS Output Hogh V OH I OH=-0.4mA V *2 Voltage Low V OL I OL=0.4mA Input Leakage Current I LKG V IN=~V SS µa *1 OSC Frequency f OSC Rf=47KΩ±2% KHz Cf=20pf±5% On Resistance R ON -=17V KΩ (Vdiv-Ci) Load current ±150µA Operating Current I DD1 aster mode ma *3 1/128 Duty I DD2 Slave mode µa *4 1/128 Duty Supply Current I EE aster mode *5 1/128 Duty Operating f op1 aster mode KHz External clock Frequency f op2 Slave mode *1. Applies to input terminals FS, DS1, DS2, CR, SHL, S and P and I/O terminals DIO1, DIO2, and in the input state. *2. Applies to output terminals, and FR and I/O terminals DIO1, DIO2, and in the output state. *3. This value is specified about current flowing through V SS. Internal oscillation circuit: Rf=47kΩ, Cf=20pF Each terminals of DS1, DS2, FS, SHL and S is connected to and out is no load. *4. This value is specified about current flowing through V SS. Each terminals is DS1, DS2, FS, SHL, P and CR is connected to, S is connected to V SS and,, DIO1 is external clock. *5. This value is specified about current flowing through. Don t connect to V LCD (~).
7 AC Charcteristics (VDD=5V±10%, Ta=-30 C~+85 C) (1)aster mode (S=, P=, Cf=20pF, Rf=47KΩ) t WLC tsu t WHC DIO1 ( SHL = ) t DH t su t WHC DIO2 ( SHL = V SS ) t D DIO2 ( SHL = ) t D DIO1 ( SHL = V SS ) t DF FR t D t D t F t R t WH1 t WL1 t DI2 t D21 t WH2 t F t R Characteristic Symbol in Typ ax Unit Data Setup Time t SU Data Hold Time t DH Data Delay Time t D FR Delay Time t DF -2-2 µs Delay Time t D -2-2 Low Level Width t WLC High Level Width t WHC Low Level Width t WL Low Level Width t WL High Level Width t WH High Level Width t WH ns - Phase Difference t D Phase Difference t D , Rise/Fall Time t R/t F
8 (2) Slave mode (S=V SS) t F t R twlc1 ( PLK2 = V SS ) t WHC t SU t WHC2 t WLC ( PLK2 = ) t R t F t D t DH hcl DIO1 ( SHL = ) DIO2 ( SHL = V SS ) Input Data t H DIO1 ( SHL = ) DIO2 ( SHL = V SS ) Output Data Characteristics Symbol in Typ ax Unit Note Low Level Width t WLC ns P=V SS High Level Width t WHC ns P=V SS Low Level Width t WLC ns P= High Level Width t WHL ns P= Data Setup Time t SU ns Data Hold Time t DH ns Data Delay Time t D ns *1 Output Data Hold Time t H ns Rise/Fall Time t R/t F ns *1; Connect load CL=30pF OUTPUT 30pF
9 FUTIONAL DESCRIPTION 1.RC Oscillator The RC Oscillator generates,,fr, of the and, of the KS0108B by the oscillation resister R and capacitor C. When selecting the master/slave, oscillation circuit is as following: 1) aster ode R CR C R CR C R f C f open open external clock 2) Slave ode R CR C open open Open 2. Timing Genertion Circuit It generates,, FR,, and by the frequency from oscillation circuit. 1) Selection of aster/slave (/S) When /S, is H, it generates,, FR,, and internally. When /S is L, it operates by receiving, from master device. 2) Frequency Selection (FS) To adjust FR by 70Hz, the oscillation frequency should be as following: FS H L Oscillation Frequency f OSC=430KHz f OSC=215Khz In the slave mode, it is connected to. 3) Duty Selection (DS1, DS2) It provides various duty selection according to DS1, DS2. DS1 DS2 DUTY L L 1/48 H 1/64 H L 1/96 H 1/128
10 3. Data Shift & Phase Select Control 1) Phase Selection It is a circuit to shift data on synchronization or rising edge or falling edge of the according to P. P H L Phase Selection Data shift on rising edge of Data shift on falling edge of 2) Data Shift Direction Selection When /S is connected to, DIO1 and DIO2 terminal is only output. When /S is connected to V SS, it depends on the SHL. S SHL DIO1 DIO2 Direction of Data H H Output Output C1 C64 L Output Output C64 C1 L H Input Output DIO1 C1 C64 DIO2 L Output Input DIO2 C64 C1 DIO1
11 TIING DIAGRA (1) 1/48 duty timing (aster mode) Condition: DS1=L, DS=L, SHL=H(L), P=H C FR DIO1 ( DIO2 ) V 0 V 0 C1 ( C48 ) V 1 V 5 V 1 C2 ( C47 ) C47 ( C2 ) C48 ( C1 ) DIO2 ( DIO1 ) - relation of ƒ DIO1 ( DIO2 ) DIO1 ( DIO2 )
12 (2) 1/128 duty timing (aster mode) - Condition: DS1=H, DS2=H, SHL=H(L), P=H C FR DIO1 ( DIO2 ) C1 ( C48 ) V 0 V 5 V 1 V 0 C2 ( C47 ) C47 ( C2 ) C48 ( C1 ) DIO2 ( DIO1 ) - relation of ƒ DIO1 ( DIO2 ) DIO1 ( DIO2 )
13 (3) 1/48 duty timing (Slave mode) - Condition: P=L, SHL=H(L) DIO1 ( DIO2 ) C1 ( C48 ) C2 ( C47 ) C47 ( C2 ) C48 ( C1 ) DIO2 ( DIO1 )
14 (4) Power driver circuit L/R R1 L/R R1 V2 R2 V3 KS0108B R1 L/R R1 L/R VR relation of duty & bias DUTY BIAS Rdiv 1/48 1/8 R2=4R1 1/64 1/9 R2=5R1 1/96 1/11 R2=7R1 1/128 1/12 R2=8R1 *When duty factor is 1/48, the value of R1 & R2 should satisfy. R1/(4R1+R2)=1/8 R1=3KΩ, R2=12KΩ
15 APPLICATION CIRCUIT -1/128 duty Segment drive(ks0108b) Interface circuit RS R/L R/W E RSTB V2R/L V3R/L DB0 ~ DB7 CS1B CS2B CS3 R/L V2R/L V3R/L R/L FR CL V SS KS0108B R/L R/L V2R/L V3R/L R/L RS R/W E RSTB DB0 ~ DB7 CS1B CS2B CS3 RS R/W E RSTB DB0 ~ DB7 CS1B CS2B CS3 FR CL V SS KS0108B CO1 LCD PANEL CO128 R/L V2R/L V3R/L R/L FR CL V SS KS0108B RS R/W E RSTB DB0 ~ DB7 CS1B CS2B CS3 FR CL V SS KS0108B VDD SHL FS S P DS2 DS1 R CR C R f Cf C1 V SS V OR/L V IR/L V 4R/L (aster) C64 V 5R/L FR DIO2 DIO1 5 2 VOR/L VIR/L R/L R/L V SS S (Slave) DIO1 R CR C FR DIO2 C1 C64 P FS DS1 DS2 SHL open open open open open open open V 0 V 1 V 2 V 3 V 4 V PU S1~S64 S 1~S64 S1~S 64 S1~S RS R/W E RSTB DB0 - DB7 15 CS1B CS2B CS3
16 PAD DIAGRA Y ( 0, 0 ) X CHIP SIZE : PAD SIZE : UNIT : m * There is mark of on the center in chip
17 PAD LOCATION PAD NAE PAD NAE PAD NAE PAD NUBER PAD NUBER PAD NUBER COORDINATE COORDINATE COORDINATE Y Y X X Y X C46 C45 C44 C43 C42 C41 C40 C39 C38 C37 C36 C35 C34 C33 C32 C31 C30 C29 C28 C27 C26 C25 C24 C CR SHL VSS S FR P DIO2 R R R R VEE C64 C63 C62 C61 C60 C59 C58 C57 C56 C55 C54 C53 C52 C51 C50 C49 C48 C C22 C21 C20 C19 C18 C17 C16 C15 C14 C13 C12 C11 C10 C9 C8 C7 C6 C5 C4 C3 C2 C1 VEE L L L L VDD DIO1 FS DS1 DS2 C R UNIT ( m)
64CH COMMON DRIVER FOR DOT MATRIX LCD INTRODUCTION FEATURES 100 QFP-1420C
INTRODUCTION The is an LCD driver LSI with 64 channel outputs for dot matrix liquid crystal graphic display systems. This device provides 64 shift registers and 64 output drivers. It generates the timing
More information32 CH COMMON DRIVER FOR DOT MATRIX LCD
_ INTRODUCTION 64 QFP is a LCD driver LSI which is fabricated by low power COS high voltage process technology. This device consists of timing generator circuit, 32 bit shift register and 32 bit driver.
More informationWuxi I-CORE Electronics Co., Ltd. AIP31107
AIP31107 64CH COON DRIER FOR DOT ATRIX LCD 1 GENERAL DESCRIPTION The AIP31107 is an LCD driver LSI with 64 channel outputs for dot matrix liquid crystal graphic display systems. This device provides 64
More informationHD44105D. (Dot Matrix Liquid Crystal Graphic Display Common Driver) Description. Features. Ordering Information
(Dot atrix Liquid Crystal Graphic Display Common Driver) Description The HD44105 is a common signal driver for LCD dot matrix graphic display systems. It generates the timing signals required for display
More informationHD61103A. (Dot Matrix Liquid Crystal Graphic Display 64-Channel Common Driver) Features. Description. Ordering Information
(Dot Matrix Liquid Crystal Graphic Display 64-Channel Common Driver) Description The is a common signal driver for dot matrix liquid crystal graphic display systems. It generates the timing signals (switch
More informationPreliminary NT7070B Dot Matrix LCD Driver & Controller. Features. Descriptions. Applications
Dot Matrix LCD Driver & Controller Features Internal Memory -Character Generator ROM -Character Generator RAM: 320 bits -Display Data RAM: 80 x 8bits for 80 digits Power Supply Voltage: 27V~55V LCD Supply
More informationHD (Dot Matrix Liquid Crystal Graphic Display Column Driver with 80-Channel Outputs) Description. Features. Ordering Information
(Dot atrix Liquid Crystal Graphic Display Column Driver with 80-Channel Outputs) Description The HD66204F/HD66204FL/HD66204TF/HD 66204TFL, the column driver for a large liquid crystal graphic display,
More informationHD44102D. (Dot Matrix Liquid Crystal Graphic Display Column Driver) Features. Description. Ordering Information
HD442 (Dot Matrix Liquid Crystal Graphic Display Column Driver) Description The HD442 is a column (segment) driver for dot matrix liquid crystal graphic display systems, storing the display data transferred
More informationHD (80-Channel Column/Common Driver for Middle- or Large-sized Liquid Crystal Panel)
(80-Channel Column/Common Driver for iddle- or Large-sized Liquid Crystal Panel) Rev 0.2 February 1996 Description The HD66206 is an 80-channel LCD driver, which is used for liquid crystal dot matrix display.
More information16COM/40SEG DRIVER & CONTROLLER FOR DOT MATRIX LCD
INTRODUCTION The is a dot matrix CD driver & controller Sl which is fabricated by low power CMOS technology. 80 QFP FUNCTION Character type dot matrix CD driver & controller Internal driver: 16 common
More informationITM-1601A LCM. User s Guide. (Liquid Crystal Display Module) 1998 Intech LCD Group Ltd. Document No. TE nd Edition Jan.
User s Guide Document No. TE-014-001 2 nd Edition Jan. 1999 ITM-1601A LCM 16 Characters X 1 lines with 5 X 8 dots format (Liquid Crystal Display Module) 1998 Intech LCD Group Ltd. ITM-1601A LCM Use s Guide
More informationDATA SHEET SBN6400G. 64-COMMON Driver for Dot-Matrix STN LCD. data sheet (v2.1) 2006 Apr 27
DATA SHEET 64-COMMON Driver for Dot-Matrix STN LCD To improve design and/or performance, Avant Electronics may make changes to its products. Please contact Avant Electronics for the latest versions of
More informationS48 LATCH & SEGMENT DRIVER ( 1 ~ 56 BITS) LATCH & SEGMENT DRIVER ( 57 ~ 112 BITS ) CLOCK GENERATOR S47 ( ARI )
INTRODUCTION The KS0035 is a general purpose LCD driving IC, and designed to be available for electronic frequency tuning display applications or microcomputer application systems. FEATURES. Maximum 53
More informationHT1620 HT1621 HT1622 HT16220 HT1623 HT1625 HT1626 HT1627 HT16270 COM
RAM Mapping 48 16 LCD Controller for I/O µc LCD Controller Product Line Selection Table HT162X HT1620 HT1621 HT1622 HT16220 HT1623 HT1625 HT1626 HT1627 HT16270 COM 4 4 8 8 8 81 16 16 16 SEG 32 32 32 32
More informationINTRODUCTION FEATURES ORDERING INFORMATION APPLICATIONS LOW POWER DTMF RECEIVER 18 DIP 300A
LOW POWER DTMF RECEIVER INTRODUCTION The is a complete Dual Tone Multiple Frequency (DTMF) receiver that is fabricated by low power CMOS and the Switched- Capacitor Filter technology. This LSI consists
More informationHT162X HT1620 HT1621 HT1622 HT16220 HT1623 HT1625 HT1626 COM
RAM Mapping 328 LCD Controller for I/O MCU PATENTED PAT No. : 099352 Technical Document Application Note Features Operating voltage: 2.7V~5.2V Built-in RC oscillator 1/4 bias, 1/8 duty, frame frequency
More informationHT162X HT1620 HT1621 HT1622 HT16220 HT1623 HT1625 HT1626 COM
RAM Mapping 328 LCD Controller for I/O C Features Operating voltage: 2.7V~5.2V Built-in RC oscillator 1/4 bias, 1/8 duty, frame frequency is 64Hz Max. 328 patterns, 8 commons, 32 segments Built-in internal
More informationSemiconductor ML9472 GENERAL DESCRIPTION FEATURES FEDL Static,1/2Duty 60 Output LCD Driver
Semiconductor Static,1/2Duty 60 Output LCD Driver FEDL9472-02 Issue Date: Feb. 1, 2008 GENERAL DESCRIPTION The is a LCD driver which can directly drive up to 60 segments in the static display mode and
More informationBlock Diagram , E I F = O 4 ) + J H 6 E E C + E H? K E J +,, H E L A H * E = I + E H? K E J + + % 8,, % 8 +, * * 6 A. H A G K A? O
PAT No. : 099352 RAM Mapping 488 LCD Controller for I/O MCU Technical Document Application Note Features Operating voltage: 2.7V~5.2V Built-in LCD display RAM Built-in RC oscillator R/W address auto increment
More informationIZ602 LCD DRIVER Main features: Table 1 Pad description Pad No Pad Name Function
LCD DRIVER The IZ602 is universal LCD controller designed to drive LCD with image element up to 128 (32x4). Instruction set makes IZ602 universal and suitable for applications with different types of displays.
More informationLC79401KNE. Overview. Features. CMOS LSI Dot-Matrix LCD Drivers
Ordering number : ENA1419 COS LSI Dot-atrix LCD Drivers http://onsemi.com Overview The is a 80-outputs segment driver LSI for graphic dot-matrix liquid crystal display systems. The latches 80 bits of display
More informationSitronix Dot Matrix LCD Controller/Driver
ST Sitronix ST766U Dot Matrix LCD Controller/Driver Features 5 x 8 and 5 x 11 dot matrix possible Low power operation support: -- 27 to 55V Wide range of LCD driver power -- to 1V Correspond to high speed
More informationAZ DISPLAYS, INC. SPECIFICATIONS FOR LIQUID CRYSTAL DISPLAY COMPLETE LCD SOLUTIONS. AGM1064B Series PART NUMBER:
AZ DISPLAYS, INC. COMPLETE LCD SOLUTIONS SPECIFICATIONS FOR LIQUID CRYSTAL DISPLAY PART NUMBER: AGM1064B Series REVISED: MAY 14, 2003 General Specification Table 1 Item Standard Value Unit Character Format
More informationRW1072-0A-001 INTRODUCTION FEATURES. Driver Output Circuit. Microprocessor Interface. Internal Memory. On-chip Low Power Analog Circuit FUNCTION
INTRODUCTION RW1072-0A-001 RW1072 is a Character Type LCD driver& controller LSI which is fabricated by low power CMOS process technology. It can display 1-lines/2-lines/3-lines with 5*8 or 6*8 dots font
More informationLC75857E LC75857W. SANYO Semiconductors DATA SHEET. Preliminary. Overview. Features. CMOS IC 1/3, 1/4 Duty LCD Display Drivers with Key Input Function
Ordering number : ENN*798 Preliminary SANYO Semiconductors DATA SHEET LC75857E LC75857W CMOS IC 1/3, 1/4 Duty LCD Display Drivers with Key Input Function Overview The LC75857E and LC75857W are 1/3 duty
More information16COM x 100SEG 1/16 Duty BITMAP LCD Driver. NJU6573! FEATURES LCD driving circuit : 16-common and 100-segment
16COM x 100SEG 1/16 Duty BITMAP LCD Driver! GENERAL DESCRIPTION PACKAGE OUTLINE The is a 16-common x 100-segment bitmap LCD driver to display graphics or characters. It incorporates 16 common driver circuits
More information1/3, 1/4 Duty LCD Driver
1/3, 1/4 Duty LCD Driver GENERAL DESCRIPTION NJU6533 is a 1/3 or 1/4 duty segment type LCD driver. It incorporates 4 common driver circuits and 32 segment driver circuits. NJU6533 can drive maximum 96
More information4-Bit Microcontroller with Built-in RC Oscillation Type A/D Converter and LCD Driver
Semiconductor MSM64P164 This version: Feb. 2000 Previous version: Sep. 1998 4-Bit Microcontroller with Built-in RC Oscillation Type A/D Converter and LCD Driver Preliminary GENERAL DESCRIPTION The MSM64P164
More informationPOWERTIP TECH. CORP. DISPLAY DEVICES FOR BETTER ELECTRONIC DESIGN
POWERTIP TECH. CORP. Specification For Approval Customer : Model Type Sample Code : LCD Module : PC2002AR-ASO-A-S0 Mass Production Code : Edition : 0 Customer Sign Sales Sign Approved By Prepared By PT-R-003-3
More informationLAPIS Semiconductor ML9058E
132-Channel LCD Driver with Built-in AM for LCD Dot Matrix Displays FEDL958E-1 Issue Date: April. 13, 27 GENEAL DESCIPTION The is an LSI for dot matrix graphic LCD devices carrying out bit map display.
More informationLC79430KNE. Overview. Features. CMOS LSI Dot-Matrix LCD Drivers
Ordering number : ENA2123 COS LSI Dot-atrix LCD Drivers http://onsemi.com Overview The is a large-scale dot matrix LCD common driver LSI. The contains an 80-bit bidirectional shift register and is equipped
More informationHT162X HT1620 HT1621 HT1622 HT16220 HT1623 HT1625 HT1626 COM
RAM Mapping 324 LCD Controller for I/O C Features Logic operating voltage: 2.4V~3.3V LCD voltage: 3.6V~4.9V Low operating current
More informationHT1621. HT1621 RAM Mapping 32x4 LCD Controller for I/O MCU
HT1621 RAM Mapping 32x4 LCD Controller for I/O MCU Features Operating voltage: 2.4V ~ 5.2V Built-in 256kHz RC oscillator External 32.768kHz crystal or 256 khz frequency source input Selection of 1/2 or
More informationLAPIS Semiconductor ML9042-xx
ML942-xx DOT MATRIX LCD CONTROLLER DRIVER FEDL942- Issue Date: Nov. 9, 23 GENERAL DESCRIPTION The ML942 used in combination with an 8-bit or 4-bit microcontroller controls the operation of a character
More informationS6A0093 Specification Revision History
Crystalfontz Thiscontrolerdatasheetwasdownloadedfrom htp:/wwwcrystalfontzcom/controlers/ S6A0093 80 SEG / 26 COM DRIVER & CONTROLLER FOR STN LCD March 2001 Ver 06 Contents in this document are subject
More informationUCS Channel LED Driver / Controller
GENERAL DESCRIPTION 3-Channel LED Driver / Controller The UCS1903 is a 3-channel LED display driver / controller with a built-in MCU digital interface, data latches and LED high voltage driving functions.
More informationBuilt-in LCD display RAM Built-in RC oscillator
PAT No. : TW 099352 RAM Mapping 488 LCD Controller for I/O MCU Technical Document Application Note Features Operating voltage: 2.7V~5.2V Built-in LCD display RAM Built-in RC oscillator R/W address auto
More informationNewhaven Display International, Inc Galvin Ct. Elgin IL, Ph: Fax:
NHD-12864AZ-FL-YBW Graphic Liquid Crystal Display Module NHD- Newhaven Display 12864-128 x 64 Pixels AZ- Model F- Transflective L- Yellow/Green LED backlight Y- STN Positive, Yellow/Green B- 6:00 Optimal
More informationNJU6549. STATIC 1/3 1/4 1/8 1/9 Segment type LCD Driver. Preliminary NJU6549
STATIC 1/3 1/4 1/8 1/9 Segment type LCD Driver GENERAL DESCRIPTION The NJU6549 is a STATIC or 1/3, 1/4, 1/8, 1/9 duty segment type LCD driver. It incorporates 9 common driver circuits and 200 segment driver
More informationST8016. Datasheet. 160 Output LCD Common/ Segment Driver IC. Version /05/25. Crystalfontz
Crystalfontz Thiscontrolerdatasheetwasdownloadedfrom htp:/www.crystalfontz.com/controlers/ 160 Output LCD Common/ Segment Driver IC Datasheet Version 1.9 2007/05/25 Note: Sitronix Technology Corp. reserves
More informationSERIAL I/O REAL TIME CLOCK
SERIAL REAL TIME CLOCK GENERAL DESCRIPTION The NJU6355 series is a serial real time clock suitable for 4 bits microprocessor. It contains quartz crystal oscillator, counter, shift register, voltage regulator,
More informationPATENTED. PAT No. : HT1622/HT1622G RAM Mapping 32 8 LCD Controller for I/O MCU. Features. General Description.
RAM Mapping 328 LCD Controller for I/O MCU PATENTED PAT No. : 099352 Features Operating voltage: 2.7V~5.2V Built-in RC oscillator 1/4 bias, 1/8 duty, frame frequency is 64Hz Max. 328 patterns, 8 commons,
More informationRAM Mapping LCD Controller for I/O MCU. Built-in LCD display RAM Built-in RC oscillator
PAT No. : 099352 RAM Mapping 4816 LCD Controller for I/O MCU Technical Document Application Note Features Operating voltage: 2.7V~5.2V Built-in LCD display RAM Built-in RC oscillator R/W address auto increment
More informationPATENTED. PAT No. : HT1622/HT1622G RAM Mapping 32 8 LCD Controller for I/O MCU. Features. General Description.
RAM Mapping 328 LCD Controller for I/O MCU PATENTED PAT No. : 099352 Features Operating voltage: 2.7V~5.2V Built-in RC oscillator 1/4 bias, 1/8 duty, frame frequency is 64Hz Max. 328 patterns, 8 commons,
More informationSitronix Dot Matrix LCD Controller/Driver
ST Sitronix ST766U Dot Matrix LCD Controller/Driver!"Features #" 5 x 8 and 5 x 11 dot matrix possible #" Low power operation support: #" -- 27 to 55V #" Wide range of LCD driver power -- to 1V #" Correspond
More informationNT7603. Features. General Description
PRELIMINARY Single-Chip 16Cx2L Dot-Matrix LCD Controller / Driver Features Internal LCD drivers 16 common signal drivers 80 segment signal drivers Maximum display dimensions 16 characters * 2 lines or
More information32.768kHz output Tuning fork Quartz Crystal Oscillator IC
32.768kHz output Tuning fork Quartz Crystal Oscillator IC GENERAL DESCRIPTION PACKAGE OUTLINE The NJU6229 is a CMOS oscillator IC which is designed for 32.768kHz tuning fork quartz unit. The NJU6229 is
More informationDEM D SBH-CW-N (4,7 ¼ -VGA)
DISPLAY Elektronik GmbH CONTENTS LCD MODULE DEM 320240D SBH-CW-N (4,7 ¼ -VGA) Product specification Version:3 19/May/2005 GENERAL SPECIFICATION MODULE NO. : DEM 320240D SBH-CW-N CUSTOMER P/N VERSION NO.
More informationHT162X HT1620 HT1621 HT1622 HT16220 HT1623 HT1625 HT1626 HT1627 HT16270 COM
RAM Mapping 328 LCD Controller for I/O C Features Operating voltage: 2.7V~5.2V Built-in RC oscillator 1/4 bias, 1/8 duty, frame frequency is 64Hz Max. 328 patterns, 8 commons, 32 segments Built-in internal
More informationNewhaven Display International, Inc Galvin Ct. Elgin IL, Ph: Fax:
NHD-12864WG-BTGH-T#N Graphic Liquid Crystal Display Module NHD- Newhaven Display 12864-128 x 64 Pixels WG- Display Type: Graphic B- Model T- White LED Backlight G- STN Positive, Gray H- Transflective,
More informationRAM Mapping 32 8 LCD Controller for I/O MCU. R/W address auto increment Built-in RC oscillator
RAM Mapping 328 LCD Controller for I/O MCU Features Operating voltage: 2.7V~5.2V R/W address auto increment Built-in RC oscillator Two selectable buzzer frequencies (2kHz or 4kHz) 1/4 bias, 1/8 duty, frame
More informationR/W address auto increment External Crystal kHz oscillator
RAM Mapping 328 LCD Controller for I/O MCU PATENTED PAT No. : 099352 Features Operating voltage: 2.7V~5.2V R/W address auto increment External Crystal 32.768kHz oscillator Two selectable buzzer frequencies
More informationRW1026 Dot Matrix 48x4 LCD Controller / Driver
Features Operating voltage: 2.4V~5.5V Internal LCD Bias generation with voltage-follower buffer External resistor CR oscillator External 256k Hz frequency source input Selection of 1/2 or 1/3 bias, and
More informationLAPIS Semiconductor ML9212
32-Bit Duplex/Triplex (1/2 duty / 1/3 duty) VF Controller/Driver with Digital Dimming FEDL9212-01 Issue Date: Nov., 26, 2002 GENERAL DESCRIPTION The is a full CMOS controller/driver for Duplex or Triplex
More informationBuilt-in LCD display RAM Built-in RC oscillator
PAT No. : TW 099352 RAM Mapping 488 LCD Controller for I/O MCU Technical Document Application Note Features Operating voltage: 2.7V~5.2V Built-in LCD display RAM Built-in RC oscillator R/W address auto
More informationRAM Mapping 64 8 LCD Controller for I/O MCU. Built-in LCD display RAM Built-in RC oscillator
RAM Mapping 648 LCD Controller for I/O MCU PATENTED PAT No. : 099352 Technical Document Application Note Features Operating voltage: 2.7V~5.2V Built-in LCD display RAM Built-in RC oscillator R/W address
More informationSemiconductor ML9060 GENERAL DESCRIPTION FEATURES FEDL FEDL /2 DUTY, 160-OUTPUT STATIC LCD DRIVER
Semiconductor 1/2 DUTY, 160-OUTPUT STATIC LCD DRIVER FEDL9060-01 This This version: Mar. Feb. 1999 2001 GENERAL DESCRIPTION The consists of a 320-bit shift register, a 320-bit data latch, 160 sets of LCD
More informationPRODUCT OVERVIEW OVERVIEW OTP
PRODUCT OVERVIEW 1 PRODUCT OVERVIEW OVERVIEW The S3C7324 single-chip CMOS microcontroller has been designed for high performance using Samsung's newest 4-bit CPU core, SAM47 (Samsung Arrangeable Microcontrollers).
More informationunit: mm 3159-QFP64E unit: mm 3190-SQFP64
Ordering number : EN*4965 CMOS LSI LC75741E, 75741W 1/2 Duty VFD Driver for Frequency Displays Preliminary Overview The LC75741E and LC75741W are 1/2 duty VFD drivers for use in electronic tuning frequency
More informationRAM Mapping 48 8 LCD Controller for I/O MCU. Built-in LCD display RAM Built-in RC oscillator
RAM Mapping 488 LCD Controller for I/O MCU Features Operating voltage: 2.7V~5.2V Built-in LCD display RAM Built-in RC oscillator R/W address auto increment External 32.768kHz crystal or 32kHz frequency
More informationHD66702 (LCD-II/E20) (Dot Matrix Liquid Crystal Display Controller/Driver) Description. Features
HD6672 (LCD-II/E2) (Dot Matrix Liquid Crystal Display Controller/Driver) Description The HD6672 LCD-II/E2 dot-matrix liquid crystal display controller and driver LSI displays alphanumerics, Japanese kana
More informationLCD MODULE DEM SBH-PW-N
Display Elektronik GmbH LCD MODULE DEM 16214 SBH-PW-N Product specification Version : 1 03/Nov/2003 GENERAL SPECIFICATION MODULE NO. : DEM 16214 SBH-PW-N CUSTOMER P/N VERSION NO. CHANGE DESCRIPTION DATE
More informationCrystalfontz. RAM Mapping 64 8 LCD Controller for I/O MCU. Built-in LCD display RAM Built-in RC oscillator
Crystalfontz Thiscontrolerdatasheetwasdownloadedfrom htp:/www.crystalfontz.com/controlers/ HT1625 RAM Mapping 648 LCD Controller for I/O MCU Features Operating voltage: 2.7V~5.2V Built-in LCD display RAM
More informationA variety of pagers day of a week, hour, minute and second. TV set and VCR CPU interface via three wires
Rev.. REAL-TIME CLOCK is a CMOS real-time clock IC, which is designed to transfer or set each data of a clock and calender as requested by a CPU. This IC is connected to the CPU by three signal buses.
More informationMM Liquid Crystal Display Driver
Liquid Crystal Display Driver General Description The MM145453 is a monolithic integrated circuit utilizing CMOS metal gate, low threshold enhancement mode devices. The chip can drive up to 33 LCD segments
More informationNTE4055B and NTE4056B Integrated Circuit CMOS, BCD to 7 Segment Decoder/Drivers
NTE4055B and NTE4056B Integrated Circuit CMOS, BCD to 7 Segment Decoder/Drivers Description: The NTE4055B ( Display Frequency Output) and NTE4056B (Strobed Latch Function) are single digit BCD to 7 segment
More information34346-OP. AUG. 06, 2003 Version 0.1
34346-OP DATA SHEET SPLC78D 6COM/4SEG Controller/Driver Preliminary AUG. 6, 23 Version. Information including Drawings, Schematics, Links and Code (Software) Supplied or eferenced in this Document is supplied
More information4-DIGIT FIXED TIMER WITH LCD DRIVER
1. GENERAL DESCRIPTION The is a countdown timer, which has six internal presettin g intervals: 1; 3; 5 ;15; 30; 60 mins. The selected time is set by connecting appropriate K i input to V cc. The K i is
More informationNTE1786 Integrated Circuit Frequency Lock Loop (FLL) Tuning & Control Circuit
NTE1786 Integrated Circuit Frequency Lock Loop (FLL) Tuning & Control Circuit Description: The NTE1786 is an integrated circuit in a 24 Lead DIP type package that provides closed loop digital tuning of
More informationHT162X HT1620 HT1621 HT1622 HT16220 HT1623 HT1625 HT1626 COM
Features Operating voltage: 2.4V~5.2V Built-in 256kHz RC oscillator External 32.768kHz crystal or 256kHz frequency source input Selection of 1/2 or1/3 bias, and selection of 1/2 or 1/3 or1/4 duty LCD applications
More informationRAM Mapping 48 8 LCD Controller for I/O C
RAM Mapping 488 LCD Controller for I/O C Features Operating voltage: 2.7V~5.2V Built-in RC oscillator External 32.768kHz crystal or 32kHz frequency source input 1/4 bias, 1/8 duty, frame frequency is 64Hz
More informationNewhaven Display International, Inc Galvin Dr. Elgin IL, Ph: Fax:
NHD-12864AZ-FSW-FBW Graphic Liquid Crystal Display Module NHD- Newhaven Display 12864-128 x 64 Pixels AZ- Model F- Transflective SW- Side White LED backlight F- FSTN Positive B- 6:00 Optimal View W- Wide
More informationDATA SHEET. PCD pixels matrix LCD controller/driver INTEGRATED CIRCUITS Apr 12
INTEGRATED CIRCUITS DATA SHEET PCD8544 48 84 pixels matrix LCD controller/driver File under Integrated Circuits, IC17 1999 Apr 12 CONTENTS 1 FEATURES 2 GENERAL DESCRIPTION 3 APPLICATIONS 4 ORDERING INFORMATION
More informationNT7605. Features. General Description
PRELIMINARY Single-chip 20CX2L Dot-Matrix LCD Controller / Driver Features! Internal LCD drivers 6 common signal drivers 00 segment signal drivers! Maximum display dimensions 20 characters * 2 lines or
More informationDATA SHEET. SEN6A39 80-COLUMN driver for dot-matrix STN LCD. data sheet (v3) 2005 Oct 20
Crystalfontz Thiscontrolerdatasheetwasdownloadedfrom htp:/www.crystalfontz.com/controlers/ DATA SHEET 80-COLUMN driver for dot-matrix STN LCD To improve design and/or performance, Avant Electronics may
More informationLC7574NE, 7574NW. 1/2 Duty VFD Driver for Frequency Display
Ordering number : EN3586A CMOS LSI LC7574NE, 7574NW 1/2 Duty VFD Driver for Frequency Display Overview The LC7574NE and LC7574NW are 1/2 duty VFD drivers that can be used for electronic tuning frequency
More informationLow Power Consumption IPS009BL9_BL9A_BLAA AT Cut 32KHz SPXO
Description IPS009BL9, IPS009BL9A and is the specific SPXO IC for achieving 32KHz output by divide, corresponding to the fundamental crystal from 14MHZ to 27MHz and 33.554MHz corresponding to each IC.
More information80CH COMMON / SEGMENT DRIVER FOR DOT MATRIX LCD
K006 0H OMMON / EGMENT RIVER FOR OT MATRIX L INTROUTION The K006 is an L driver LI which is fabricated by low power MO high voltage process technology. In segment driver mode, it can be interfaced in -bit
More informationNewhaven Display International, Inc Galvin Ct. Elgin IL, Ph: Fax:
NHD-12864WG-BTFH-V#N Graphic Liquid Crystal Display Module NHD- Newhaven Display 12864-128 x 64 pixels WG- Display Type: Graphic B- Model T- White LED Backlight F- FSTN (+) H- Transflective, Wide Temperature
More informationPRODUCT SPECIFICATIONS C-1602A-1YN
PRODUCT SPECIFICATIONS C-1602A-1YN TABLE OF CONTENT 1 COMPOSITION 2 2 MECHANICAL SPECIFICATION 2 3 DIMENSION DIAGRAM 2 4 OPTICAL CHARACTERISTICS 3 4.1 OPTICAL MEASUREMENT SYSTEM 3 4.2 CONTRAST RATIO Cr
More information180-Channel LCD Driver with Built-in RAM for LCD Dot Matrix Displays
180-Channel LCD Driver with Built-in RAM for LCD Dot Matrix Displays FEDL9445-01 Issue Date: Apr. 27, 2012 GENERAL DESCRIPTION The is an LSI for dot matrix graphic LCD devices carrying out bit map display.
More informationNHD-12864AZ-FSW-GBW-VZ
NHD-12864AZ-FSW-GBW-VZ Graphic Liquid Crystal Display Module NHD- Newhaven Display 12864-128 x 64 pixels AZ- Model F- Transflective SW- Side White LED backlight G- STN- Gray B- 6:00 View W- Wide Temperature
More informationSitronix ST7063C. !"Functions. !"Features. !"Description. 80CH Segment Driver for Dot Matrix LCD. #"Dot matrix LCD driver with two 40 channel
T itronix CH egment river for ot atrix LC!"Functions!"Features #"ot matrix LC driver with two channel outputs #"Bias voltage ( ~ ) #"input/output signals!"input : erial display data and control pulse from
More informationUNISONIC TECHNOLOGIES CO., LTD 1812A/1812B/1813
UNISONIC TECHNOLOGIES CO., LTD 2A/2B/ SINGLE SOUND GENERATOR DESCRIPTION The UTC 2A/2B/ is a CMOS LSI chip designed for use in sound effect products.it is equipped with tone circuit, noise circuit and
More informationHT162X HT1620 HT1621 HT1622 HT16220 HT1623 HT1625 HT1626 COM
RAM Mapping 324 LCD Controller for I/O C Features Operating voltage : 2.4V~5.2V Built-in 256kHz RC oscillator External 32.768kHz crystal or 256kHz frequency source input Selection of 1/2 or 1/3 bias, and
More informationHT9170 Series Tone Receiver
Tone Receiver Features Operating voltage: 2.5V~5.5V Minimal external components No external filter is required Low standby current (Power-down mode) General Description The HT9170 series are Dual Tone
More informationML9478C GENERAL DESCRIPTION FEATURES. FEDL9478C-01 Issue Date: Apr. 25, Static, 1/2 Duty, 1/3 Duty, 1/4 Duty 80 Outputs LCD Driver
Static, 1/2 Duty, 1/3 Duty, 1/4 Duty 80 Outputs LCD Driver FEDL9478C-01 Issue Date: Apr. 25, 2012 GENERAL DESCRIPTION The is an LCD driver LSI, consists of a 80-bit shift register, a 320-bit data latch,
More informationLow current consumption : 0.4 ma typ. Driver output current : 70 ma max. 5 MHz (cascade connection) Selectable H/L for latch and driver enable
The is a CMOS thermal print head driver containing a 64-bit shift register and a latch. It can be used for general purpose because H or L can be selected for the latch and the driver enable. It is ideal
More informationAddendum/Corrections to the prel. Data Sheet (Version 1.1) and to the Delta Sheet (Version 1.2)
Quad ISDN 4B3T Echocanceller Digital Frontend DFE-T PEB 24901 Versions 1.1/1.2 Addendum/Corrections 07.99 to the prel. Data Sheet 02.95 (Version 1.1) and to the Delta Sheet 06.96 (Version 1.2) 1 Electrical
More information1/8, 1/9, 1/10 Duty BITMAP LCD DRIVER with KEY SCAN
1/8, 1/9, 1/1 Duty BITMAP LCD DRIVER with KEY SCAN PRELIMINARY GENERAL DESCRIPTION The NJU6538 is a 1-common x 65-segment bitmap LCD driver to display graphics or characters. It contains 65 bits display
More informationS-35190A 3-WIRE REAL-TIME CLOCK. Rev.2.4_00. Features. Applications. Package. Seiko Instruments Inc. 1
Rev.2.4_00 3-WIRE REAL-TIME CLOCK Features The is a CMOS 3-wire real-time clock IC which operates with the very low current consumption and in the wide range of operation voltage. The operation voltage
More informationSemiconductor MSC GENERAL DESCRIPTION FEATURES FEDL FEDL This version: MSC Sep Previous version: Nov.
Semiconductor 17 2 Duplex Driver with Dimming, Keyscan and A/D Converter Function FEDL1215-03 This version: Sep. 2000 Previous version: Nov. 1997 GENERAL DESCRIPTION The is a 1/2-duty vacuum fluorescent
More informationNT Output LCD Segment/Common Driver NT7703. Features. General Description. Pin Configuration 1 V1.0
160 Output LCD Segment/Common Driver Features (Segment mode)! Shift Clock frequency: 14 MHz (Max.) (VDD = 5V ± 10%) 8 MHz (Max.) (VDD = 2.5V - 4.5V)! Adopts a data bus system! 4-bit / 8-bit parallel input
More informationDISPLAY Elektronik GmbH LCD MODULE DEM T SBH-PW-N. Product Specification Version: Version: 2 PAGE: 1
DISPLAY Elektronik GmbH LCD MODULE DEM 128064T SBH-PW-N Version: 1 22.02.2013 Version: 2 PAGE: 1 GENERAL SPECIFICATION MODULE NO. : DEM 128064T SBH-PW-N VERSION NO. CHANGE DESCRIPTION DATE 0 ORIGINAL VERSION
More informationUNISONIC TECHNOLOGIES CO., LTD CD4541
UNISONIC TECHNOLOGIES CO., LTD CD4541 PROGRAMMABLE TIMER DESCRIPTION The CD4541 programmable timer comprise a 16-stage binary counter, an integrated oscillator for use with an external capacitor and two
More informationMM5452/MM5453 Liquid Crystal Display Drivers
MM5452/MM5453 Liquid Crystal Display Drivers General Description The MM5452 is a monolithic integrated circuit utilizing CMOS metal gate, low threshold enhancement mode devices. It is available in a 40-pin
More informationNJU6063. RGB LED Controller Driver with PWM Control FEATURES BLOCK DIAGRAM NJU6063V - 1 -
RGB LED Controller Driver with PWM Control GENERAL DESCRIPTION The NJU6063 is RGB LED controller driver with PWM control. It contains PWM controller, LED drivers, I 2 C interface and constant current driver
More informationFeatures. Support for external one-path, internal three-path D/A converter reference voltages
AK2330 DAC Type 8-bit 8-channel Electronic Volume Features 8-bit 8 channels of built-in multiplication D/A converters Support for external one-path, internal three-path D/A converter reference voltages
More informationST DESCRIPTION 2. FEATURES. Crystalfontz. Thiscontrolerdatasheetwasdownloadedfrom htp:/
Crystalfontz Thiscontrolerdatasheetwasdownloadedfrom htp:/www.crystalfontz.com/controlers/ ST ST8009 96 Output LCD Common/ Segment Driver IC Notice: Sitronix Technology Corp. reserves the right to change
More information