NJM324C. Low power quad operational amplifiers
|
|
- Polly Watkins
- 5 years ago
- Views:
Transcription
1 Low power quad operational amplifiers Features Wide gain bandwidth:.mhz typ. Input common-mode voltage range includes ground Large voltage gain:db typ. Very low supply current per amplifier:ua typ. Low input bias current: na typ. Low input offset voltage: 7mV max Low input offset current: na typ. Wide power supply range: - Single supply: +V to +V - Dual supplies: ±.V to ±V Internal ESD protection Human body model (HBM) ±V typ. NJM4CG ( SOP4 ) Description The NJM4C consist of four independent, high gain, internally frequency-compensated operational amplifiers. They operate from a single power supply over a wide range of voltages. Operation from split power supplies is also possible and the low power supply current drain is independent of the magnitude of the power supply voltage. Pin and schematic diagram Figure. Pin connections (top view) Output 4 4 Output 4 Inverting Input Inverting Input 4 Non-inverting Input Non-inverting Input 4 V CC + 4 V CC - Non-inverting Input Non-inverting Input Inverting Input Output Inverting Input Output ver. - -
2 Figure. Schematic diagram (/4 NJM4C) Vcc + V CC 6µA C C 4µA µa Q Q6 Inverting inverting Input Input Non-Inverting non-inverting Input Input Q Q Q Q4 Q Q Q7 Q R SC Output Q Q8 Q9 µa GND Vcc - Absolute maximum ratings Table. Absolute maximum ratings Symbol Parameter NJM4C Unit V CC Supply voltage (V CC + - V CC - ) V V i Input voltage () -. to V V id Differential input voltage ± V I in Output short-circuit duration () Infinite Input current () :Vin driven negative ma in DC or ma in AC (duty cycle = %, T=s) Input current (4) :Vin driven positive above AMR value.4 T stg Storage temperature range -6 to + C T j Maximum junction temperature C P D Power Dissipation () 88 (6) (7) mw θja Thermal resistance junction to ambient ψjt Thermal resistance junction to top surface of IC package 4(6) 4(6) ma (7) C /W (7) C /W. Input voltage is the voltage should be allowed to apply to the input terminal independent of the magnitude of V CC +. Short-circuits from the output to V CC can cause excessive heating if V CC > V. Destructive dissipation can result from simultaneous short circuits on all amplifiers.. This input current only exists when the voltage at any of the input leads is driven negative. It is due to the collector-vase junction of the input PNP transistor becoming forward-biased and thereby acting as input diode clamp. In addition to this diode action, there is NPN parasitic action on the IC chip. This transistor action can cause the output voltages of the Op-amps to go to the V CC voltage level (or to ground for a large overdrive) for the time during which an input is driven negative. 4. The junction base/substrate of the input PNP transistor polarized in reverse must be protected by a resistor in series with the inputs to limit the input current to 4uA max (R= (Vin-V)/4uA).. Short-circuit can cause excessive heating and destructive dissipation. Values are typical. 6. EIA/JEDEC STANDARD Test board (76. x 4. x.6mm, layers, FR-4) mounting 7. EIA/JEDEC STANDARD Test board (76. x 4. x.6mm, 4layers, FR-4) mounting - - ver.
3 . Operating conditions Table. Operating conditions Symbol Parameter Value Unit V CC Supply voltage (V CC + - V CC - ) to V V icm Common mode input voltage range V CC - -. to V CC + -. V T oper Operating free-air temperature range -4 to +8 C 4. Electrical characteristics Table. V CC + = +V, V CC - = V, T amb = + C, T min = C,T max =7 C (unless otherwise specified) Symbol Parameter Min. Typ. Max. Unit V io Input offset voltage () I io I ib A vd SVR I CC V icm CMR I source Input offset current Input bias current () Large signal voltage gain V + CC = +V, RL=kΩ, Vo=.4V to.4v Supply voltage rejection ratio (Rs<kΩ) V + CC = V to V Supply current, all amp, no load V + CC = V -. V + CC = V -.7 V + CC = V - - V + CC = V - - Input common mode voltage range + V CC = +V () - V + CC -. - V + CC - Common mode rejection ratio (R S < kω) Output current source (V id = +V) V + CC = V, V O = +V, 4 - mv na na V/mV db ma ma V db ma ver. - -
4 Table4. V CC + = +V, V CC - = V, T amb = + C, T min = C,T max =7 C (unless otherwise specified) Symbol Parameter Min. Typ. Max. Unit Output sink current (V id = -V) I sink V CC + = V, V o = +V - ma V CC + = V, V o = +.V - ua High level output voltage V CC + = V, RL = kω V V OH T amb =+ C,RL = kω V CC + = V, RL = kω V V OL Low level output voltage RL = kω - mv - - SR GBP THD e n Slew rate V + CC = V, V i =. to V, R L = kω, C L = pf, unity gain Gain bandwidth product V + CC = V, f = khz, V in =mv, R L = kω, C L = pf Total harmonic distortion f = khz, A V =db, R L = kω, V O = V pp, C L = pf, V + CC = V Equivalent input noise voltage f = khz, R S =Ω, V + CC = V V/µs -. - MHz -. - % - - nv/ Hz DV io Input offset voltage drift - 7 µv/ C DI io Input offset current drift - pa/ C V O /V O Channel separation (4) khz < f < khz - - db. V O =.4V, R S =Ω, V < V CC + < V, < V ic < V CC + -.V.. The direction of the input current is out of the IC.. The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than.v. The upper end of the common-mode voltage range is V CC + -.V, but either or both inputs can go to +V without damage. 4. Due to the proximity of the external components, ensure that stray capacitance between these external parts dose not cause coupling. Coupling can be detected because this type of capacitance increases at higher frequencies.. This parameter is not % test ver.
5 TYPICAL CHARACTERISTICS 6 Gain/Phase vs. Frequency V CC + =V, G V =4dB, R L =kω to V CC -, C L =pf Maximum Output Voltage Swing vs. Frequency V CC + =V, Voltage Gain [db] Gain Phase Ta=-4 C Ta=-4 C k k k M M Frequency [Hz] Phase [deg] Maximum Output Voltage Swing V OPP [V PP ] k k k M Frequency [Hz] Pulse Response V CC + =V, R L =kω, C L =pf, Small signal Pulse Response V CC + =V, G V =db, C L =pf, Voltage [V/div] V IN V OUT Input/Output Voltage [mv] 4 4 Output Input Time [µs/div] Time [µs/div] Maximum Output Voltage vs. Load Resistance V CC + =V, R L to V CC - Maximum Output Voltage vs. Load Resistance V CC + =V, R L to V CC - Maximum Output Voltage [V] Ta=-4 C Ta=-4 C, ºC, 8ºC Maximum Output Voltage [V] 4 Ta=-4 C Ta=-4 C, ºC, 8ºC k k k Load Resistance [Ω] k k k Load Resistance [Ω] ver. - -
6 TYPICAL CHARACTERISTICS. Maximum Output Voltage vs. Load Resistance V CC + =V, R L to V CC - Maximum Output Voltage vs. Output Current V CC + /V CC - =±V Maximum Output Voltage [V]..... Ta=-4 C Ta=-4 C, ºC, 8ºC Maximum Output Voltage [V] - - Isource Isink Ta=-4 C Ta=-4 C k k k Load Resistance [Ω] - k Output Current [ma] Output Voltage vs. Output Sink Current V CC + =V, Ta=ºC Input Voltage Range vs. Supply Voltage Output Voltage [V]. Input Voltage [V] Negative Positive. k k k Output Sink Current[µA] ± ± ± Supply VoltageV CC + /V CC - [V]. Supply Current vs. Supply Voltage G V =db. Supply Current vs. Temperature G V =db Supply Current [ma]..... Ta=ºC Ta=8ºC Ta=-4ºC Supply Current [ma]..... V CC + =V V CC + =V V CC + =V Supply Voltage V CC + [V] Ambient Temperature [ C] ver.
7 TYPICAL CHARACTERISTICS Input Offset Voltage vs. Supply Voltage V CM =V CC + / Input Offset Voltage vs. Temperature V CM =V CC + / - - Ta=-4 C - - V CC + =V V CC + =V V CC + =V Supply Voltage V CC + [V] Ambient Temperature [ C] Input Offset Voltage vs. Common-Mode Input Voltage V CC + =V Input Offset Voltage vs. Common-Mode Input Voltage V CC + =V - Ta=-4 C - Ta=-4 C - - Common-Mode Input Voltage [V] Common-Mode Input Voltage [V] Input Offset Voltage vs. Common-Mode Input Voltage V CC + =V Input Bias Current vs. Temperature V CM =V CC + / - Ta=-4 C Input Bias Current [na] 4 V CC + =V V CC + =V V CC + =V Common-Mode Input Voltage [V] Ambient Temperature [ºC] ver
8 TYPICAL CHARACTERISTICS 6 Voltage Gain vs. Supply Voltage Ta= C 4 Large Signal Voltage Gain vs. Temperature V CC + =V, R L =kω, V O =V to V Voltage Gain [db] R L =kω R L =kω Large Signal Voltage Gain [db] Supply Voltage V CC + [V] Ambient Temperature [ C] 4 CMR vs. Frequency V CC + /V CC - =±7.V, 4 Large Signal Voltage Gain vs. Frequency V CC + =V Common-Mode Rejection Ratio [db] Large Signal Voltage Gain [db] k k k M Frequency [Hz]. k k k M Frequency [Hz] ver.
9 PACKAGE OUTLINE UNIT : mm 8.7±..9±. 6.±.4 UNIT: mm ±. TOTAL.4±.. M. S S ~ [CAUTION] The specifications on this data book are only given for information, without any guarantee as regards either mistakes or omissions. The application circuits in this data book are described only to show representative usages of the product and not intended for the guarantee or permission of any right including the industrial rights. ver
Low power quad operational amplifiers
Low power quad operational amplifiers Features Wide gain bandwidth:.mhz typ. Input common-mode voltage range includes ground Large voltage gain:db typ. Very low supply current per amplifier:ua typ. Low
More informationLow power dual operational amplifier
Low power dual operational amplifier NJM58C / NJM58CA Features Internally frequency-compensated Large DC voltage gain : db typ. Wide bandwidth (unity gain ) :.MHz typ. Low Operating Current : 5 ua/ch typ.
More informationNJM320A/NJM321A. Low power single channel OP-Amp
Low power single channel OPAmp NJMA/NJMA Features Input offset voltage :.mv max. Input offset voltage drift : µv/ typ. Supply current :.ma typ. at Vcc + =V Input bias current : na typ. Input commonmode
More informationLM2904AH. Low-power, dual operational amplifier. Related products. Description. Features. See LM2904WH for enhanced ESD performances
LM2904AH Low-power, dual operational amplifier Datasheet - production data Related products See LM2904WH for enhanced ESD performances Features Frequency compensation implemented internally Large DC voltage
More informationLM158,A-LM258,A LM358,A
,A-LM258,A LM358,A LOW POWER DUAL OPERATIONAL AMPLIFIERS INTERNALLY FREQUENCY COMPENSATED LARGE DC VOLTAGE GAIN: 1dB WIDE BANDWIDTH (unity gain): 1.1MHz (temperature compensated) VERY LOW SUPPLY CURRENT/OP
More informationRT2902. RobuST low-power quad operational amplifier. Applications. Description. Features
RobuST low-power quad operational amplifier Datasheet - production data Features D SO14 (plastic micropackage) Pin connections (top view) Output 1 Non-inverting Input 1 3 Non-inverting Input 2 Inverting
More informationPart Number Temperature Range Package Packing Marking. DIP14 Tube LM2902N LM2902D/DT SO-14 Tube or Tape & Reel
Low Power Quad Operational Amplifier Wide gain bandwidth: 1.3MHz Input common-mode voltage range includes ground Large voltage gain: 1dB Very low supply current per amp: 375µA Low input bias current: 2nA
More informationNJM5532C LOW-NOISE DUAL OPERATIONAL AMPLIFIER NJM5532CG (SOP8) FEATURES PIN CONFIGURATION. EQUIVALENT CIRCUIT (Each Amplifier) - 1 -
LOWNOISE DUAL OPERATIONAL AMPLIFIER NJM3C GENERAL DESCRIPTION The NJM3C is a high performance dual low noise operational amplifier. This features low noise performance (nv/ Hz), and considerably higher
More informationNJM2904C / NJM2904CA SINGLE-SUPPLY DUAL OPERATIONAL AMPLIFIER
NJM94C / NJM94CA SINGLE-SUPPLY DUAL OPERATIONAL AMPLIFIER GENERAL DESCRIPTION The NJM94C / NJM94CA consists of two independent, high gain, internally frequency compensated operation amplifiers, which were
More informationLM2904, LM2904A. Low-power dual operational amplifier. Description. Features. Related products:
, A Low-power dual operational amplifier Datasheet - production data Features Frequency compensation implemented internally Large DC voltage gain: 100 db Wide bandwidth (unity gain): 1.1 MHz (temperature
More informationLow-Power Quad Operational Amplifier FEATURES: DESCRIPTION: Memory. Logic Diagram. RAD-PAK technology-hardened against natural space radiation
Low-Power Quad Operational Amplifier FEATURES: RAD-PAK technology-hardened against natural space radiation Total dose hardness: - > 100 krad (Si), depending upon space mission Excellent Single Event Effects:
More informationRT2904WH. RobuST low-power dual operational amplifier. Applications. Features. Description
RobuST low-power dual operational amplifier Datasheet - production data Features D SO8 (plastic micropackage) Pin connections (top view) Frequency compensation implemented internally Large DC voltage gain:
More informationNJM2734SCC. Rail-to-Rail Input/Output Quad Operational Amplifier PACKAGE OUTLINE
Rail-to-Rail Input/Output Quad Operational Amplifier GENERAL DESCRIPTION NJM74SCC is a Rail-to-Rail Input/Output quad operational amplifier featuring Low power, low noise and operation from.8v. Rail-to-Rail
More informationNJM4558C DUAL OPERATIONAL AMPLIFIER V + OUTPUT -INPUT +INPUT V -
NJM48C DUAL OPERATIONAL AMPLIFIER GENERAL DESCRIPTION The NJM48C integrated circuit is a dual high-gain operational amplifier internally compensated and constructed on a single silicon chip. Combining
More informationNJM2734. Rail-to-Rail Input/Output Quad Operational Amplifier
Rail-to-Rail Input/Output Quad Operational Amplifier NJM2734 GENERAL DESCRIPTION NJM2734 is a Rail-to-Rail Input/Output quad operational amplifier featuring Low power, low noise and operation from.8v.
More informationObsolete Product(s) - Obsolete Product(s)
Low power quad operational amplifier Features Wide gain bandwidth: 1.3 MHz Extended temperature range: -40 C to +150 C Input common-mode voltage range includes negative rail Large voltage gain: 100 db
More informationUNISONIC TECHNOLOGIES CO., LTD LM321
UNISONIC TECHNOLOGIES CO., LTD LM321 LOW POWER SINGLE OP AMP DESCRIPTION The UTC LM321 s quiescent current is only 430µA (5V). The UTC LM321 brings performance and economy to low power systems, With a
More informationLF147 - LF247 LF347 WIDE BANDWIDTH QUAD J-FET OPERATIONAL AMPLIFIERS
LF147 - LF247 LF347 WIDE BANDWIDTH QUAD J-FET OPERATIONAL AMPLIFIERS LOW POWER CONSUMPTION WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT OUTPUT SHORT-CIRCUIT
More informationLM158/LM258/LM358/LM2904 Low Power Dual Operational Amplifiers
LM158/LM258/LM358/LM2904 Low Power Dual Operational Amplifiers General Description The LM158 series consists of two independent, high gain, internally frequency compensated operational amplifiers which
More informationNJM2718. Single-Supply High-Operating voltage Dual Operational Amplifier PACKAGE OUTLINE
Single-Supply High-Operating voltage Dual Operational Amplifier GENERAL DESCRIPTION The NJM2718 is a single-supply high-operating voltage dual operational amplifier. It is suitable for high supply voltage
More informationRail-to-Rail Input/Output Quad Operational Amplifier 8. C OUTPUT 9. C -INPUT 10. C +INPUT 11. GND(V ) 12. D +INPUT 13. D INPUT 14.
Rail-to-Rail Input/Output Quad Operational Amplifier GENERAL DESCRIPTION is a Rail-to-Rail Input/Output quad operational amplifier featuring Low power, low noise and operation from.8v. Rail-to-Rail Input/Output
More informationNJM2722. Single Ultra-High speed and Wide Band Operational Amplifier
Single Ultra-High speed and Wide Band Operational Amplifier GENERAL DESCRIPTION The NJM2722 is a single, ultra-high speed and wide band operational amplifier that features 1V/μs slew rate and 1ohm load
More informationNJM8512/NJM8513. Precision, JFET Input Operational Amplifier
Precision, JFET Input Operational Amplifier NJM8512/NJM8513 FEATURES Low Input Offset Voltage V IO =4μV max. V IO =7μV max. (Ta= -4 C to +125 C) Low Input Offset Voltage Drift ΔV IO /ΔT=5μV/ C max. (Ta=
More informationNJM2732. Rail-to-Rail Input/Output Dual Operational Amplifier
Rail-to-Rail Input/Output Dual Operational Amplifier NJM7 GENERAL DESCRIPTION The NJM7 is a Rail-to-Rail Input/Output dual operational amplifier featuring low power, low noise and a low voltage operation
More informationLF153 LF253 - LF353 WIDE BANDWIDTH DUAL J-FET OPERATIONAL AMPLIFIERS
LF153 LF253 - LF353 WIDE BANDWIDTH DUAL J-FET OPERATIONAL AMPLIFIERS LOW POWER CONSUMPTION WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT OUTPUT SHORT-CIRCUIT
More informationLM158, LM258, LM358. Low-power dual operational amplifiers. Related products. Description. Features. See LM158W for enhanced ESD ratings
Low-power dual operational amplifiers Datasheet - production data Related products See LM158W for enhanced ESD ratings Features Frequency compensation implemented internally Large DC voltage gain: 100
More informationLM2902. Low power quad operational amplifier. Features. Description
Low power quad operational amplifier Features Wide gain bandwidth: 1.3MHz Input common-mode voltage range includes negative rail Large voltage gain: 100dB Very low supply current per amp: 375µA Low input
More informationTL072 TL072A - TL072B
A - B LOW NOISE J-FET DUAL OPERATIONAL AMPLIFIERS WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT LOW NOISE e n = 15nV/ Hz (typ) OUTPUT SHORT-CIRCUIT PROTECTION
More informationNJM4585. Low Noise, Bipolar Input Dual, Audio Operational amplifier EQUIVALENT CIRCUIT PIN CONFIGURATION. FEATURES Designed for High-Quality Sound
Low Noise, Bipolar Input Dual, Audio Operational amplifier DESCRIPTION NJM48 is a low noise bipolar input dual audio operational amplifier featuring.nv/ Hz at khz. The NJM48 features Low distortion, high
More informationLM321 Low Power Single Op Amp
Low Power Single Op Amp General Description The LM321 brings performance and economy to low power systems. With a high unity gain frequency and a guaranteed 0.4V/µs slew rate, the quiescent current is
More informationNJM2720. Single Ultra-High speed and Wide Band Operational Amplifier
NJM272 Single Ultra-High speed and Wide Band Operational Amplifier GENERAL DESCRIPTION The NJM272 is a single, ultra-high speed and wide band operational amplifier that features 2V/μs slew rate and 1ohm
More informationLow Offset, Low Drift Dual JFET Input Operational Amplifier. NJM2749M, NJM2749AM : DMP8 NJM2749E, NJM2749AE : SOP8 JEDEC 150mil V + OUTPUT B INPUT B
Low Offset, Low Drift Dual JFET Input Operational Amplifier GENRRAL DESCRIPTION The NJM2749/2749A is a Precision dual JFET input operational amplifier which includes low input offset voltage:.8mv (typ)
More informationWide-Band,High-Speed,Low-Offset,Low-Noise Rail-to-Rail Input/Output CMOS Operational Amplifier
NJU777 Wide-Band,High-Speed,Low-Offset,Low-Noise Rail-to-Rail Input/Output CMOS Operational Amplifier GENERAL DESCRIPTION The NJU777 are Rail-to-Rail input/output CMOS single/dual/quad operational amplifiers.
More informationLM224A, LM324A. Low-power quad operational amplifiers. Features. Description
Low-power quad operational amplifiers Features Datasheet - production data D SO14 (plastic micropackage) Wide gain bandwidth: 1.3 MHz Input common mode voltage range includes ground Large voltage gain:
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. -LM258-LM358 A-LM258A-LM358A Low power dual operational amplifiers Features
More informationLM2904WH. Low-power dual operational amplifier. Description. Features
Low-power dual operational amplifier Datasheet - production data MiniSO8 Wafer form SO8 Features Frequency compensation implemented internally Large DC voltage gain: 100 db Wide bandwidth (unity gain:
More informationHIGH SPEED SINGLE SUPPLY OPERATIONAL AMPLIFIER V + B OUTPUT B -INPUT B +INPUT SOP8 SSOP8 MSOP8(VSP8) SOP14 SSOP14
HIGH SPEED SINGLE SUPPLY OPERATIONAL AMPLIFIER FEATURES High Slew Rate 10V/µs High Bandwidth 3MHz High Unity Gain Frequency 3.6MHz Input Offset Voltage 5.5mV max. Single Supply 3V to 36V Operating Temperature
More informationNJM2748/2748A. Low Offset, Low Drift single JFET Input Operational Amplifier -1-
Low Offset, Low Drift single JFET Input Operational Amplifier NJM2748/2748A GENERAL DESCRIPTION The NJM2748/2748A is a Precision dual JFET input operational amplifier which includes low input offset voltage:.7mv
More informationLM2904 LOW POWER DUAL OPERATIONAL AMPLIFIERS. INTERNALLY FREQUENCY COMPENSATED LARGE DC VOLTAGE GAIN : 100dB
LOW POWE DUAL OPEATIONAL AMPLIFIES INTENALLY FEQUENCY COMPENSATED LAGE DC VOLTAGE GAIN : 1dB WIDE BANDWIDTH (unity gain) : 11MHz (temperature compensated) VEY LOW SUPPLY CUENT/AMPLI (5µA) - ESSENTIALLY
More informationSINGLE SUPPLY QUAD OPERATIONAL AMPLIFIER
NJM SINGLE SUPPLY QUAD OPERATIONAL AMPLIFIER GENERAL DESCRIPTION The NJM is single-supply quad operational amplifier, which can operate from V supply. The features are low offset voltage, low bias current,
More informationLM12 4 LM LM3 2 4
LM12 4 LM2 2 4 - LM3 2 4. LOW POWER QUAD OPERATIONAL AMPLIFIERS. WIDE GAIN BANDWIDTH : 1.3MHz. INPUT COMMON-MODE VOLTAGE RANGE INCLUDES GROUND LARGE VOLTAGE GAIN : 100dB. VERY LOW SUPPLY CURRENT/AMPLI
More informationNJM8801. High Quality Audio Dual Operational Amplifier FEATURES. EQUIVALENT CIRCUIT ( 1/2 Shown ) -1-
High Quality Audio Dual Operational Amplifier NJM88 GENERAL DESCRIPTION The NJM88 is a high quality audio dual operational Amplifier with bipolar technology, strikes a balance between MUSES technology
More informationLM124 LM224 - LM324 LOW POWER QUAD OPERATIONAL AMPLIFIERS
LM224 - LM324 LOW POWER QUAD OPERATIONAL AMPLIFIERS. WIDE GAIN BANDWIDTH : 1.3MHz INPUT COMMON-MODE VOLTAGE RANGE INCLUDES GROUND LARGE VOLTAGE GAIN : 100dB. VERY LOW SUPPLY CURRENT/AMPLI : 375µA LOW INPUT
More informationMUSES8920. High Quality Audio J-FET Input Dual Operational Amplifier - 1 -
MUSES9 High Quality Audio J-FET Input Dual Operational Amplifier GENERAL DESCRIPTION The MUSES9 is a high quality audio J-FET input dual operational amplifier, which is optimized for high-end audio, professional
More informationNJM12904 SINGLE SUPPLY DUAL AMPLIFIER -INPUT +INPUT OUTPUT GND(V-)
NJM1294 SINGLE SUPPLY DUAL AMPLIFIER GENERAL DESCRIPTION The NJM1294 is a single-supply dual operational amplifier, which can operate from 2V supply. The features are low offset voltage, low bias current.
More informationMUSES8832. Rail-to-Rail Output, High Quality Audio, Dual Operational Amplifier. MUSES and this logo are trademarks of New Japan Radio Co., Ltd.
MUSES Rail-to-Rail Output, High Quality Audio, Dual Operational Amplifier GENERAL DESCRIPTION The MUSES is a Rail-to-Rail output High quality audio operational amplifier, which is optimized for high-end
More informationHigh Output Current, Rail-to-Rail Input/Output Dual CMOS Operational Amplifier PIN FUNCTION 1. OUTPUT A 2. INPUT A 3. +INPUT A
High Current, Rail-to-Rail / Dual CMOS Operational Amplifier NJU74 GNERAL DESCRIPTION The NJU74 is a Rail-to-Rail / dual CMOS operational amplifier. Based on C-MOS technology, there are excellent features
More informationLM392/LM2924 Low Power Operational Amplifier/Voltage Comparator
LM392/LM2924 Low Power Operational Amplifier/Voltage Comparator General Description The LM392 series consists of 2 independent building block circuits. One is a high gain, internally frequency compensated
More informationDUAL OPERATIONAL AMPLIFIER
DUAL OPERATIONAL AMPLIFIER FEATURES n Wide Power Supply Range Single Supply: 3V ~ 32V Dual Supplies: ±.V ~ ±6V n Lower Input Offset : 2mV (Typ.) n Input CommonMode Range Include Ground n Differential Input
More informationNJU7026/NJU7027/NJU7028
NJU76/NJU77/NJU78 μa/ch, Rail-to-Rail Output CMOS Operational Amplifier FEATURES (V + =5V, V - =V, Ta=5 C, typ.) Supply Current (All Amplifiers) NJU76 µa NJU77 6µA NJU78 8µA Supply Voltage.8V to 5.5V Gain
More informationUNISONIC TECHNOLOGIES CO., LTD LM833 Preliminary CMOS IC
UNISONIC TECHNOLOGIES CO., LTD LM833 Preliminary CMOS IC DUAL OPERATIONAL AND LOW VOLTAGE NOISE AMPLIFIER DESCRIPTION The UTC LM833 is integrated circuit amplifiers which combine dual operational and low
More informationNJU7076/NJU7077/NJU7078
NJU776/NJU777/NJU778 Precision, Low Noise, Rail-to-Rail Output, CMOS Operational Amplifier GENERAL DESCRIPTION The NJU776/NJU777/NJU778 is a high precision Rail-to-Rail output Single/Dual/Quad CMOS operational
More informationLF147 - LF247 LF347 WIDE BANDWIDTH QUAD J-FET OPERATIONAL AMPLIFIERS
LF147 - LF247 LF347 WIDE BANDWIDTH QUAD J-FET OPERATIONAL AMPLIFIERS LOW POWER CONSUMPTION WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT OUTPUT SHORT-CIRCUIT
More informationOPERATIONAL AMPLIFIER & VOLTAGE REFERENCE KL103/A TECHNICAL DATA DESCRIPTION. PIN CONNECTIONS (top view) OPERATIONAL AMPLIFIER
TECHNICAL DATA OPERATIONAL AMPLIFIER & OLTAGE REFERENCE KL13/A OPERATIONAL AMPLIFIER LOW INPUT OFFSET OLTAGE :. typ. LOW SUPPLY CURRENT : 3 A/op. (@ cc = ) MEDIUM BANDWIDTH (unity gain) :.9MHz LARGE OUTPUT
More informationLM101A-LM201A LM301A SINGLE OPERATIONAL AMPLIFIERS
LM1A-LM201A LM301A SINGLE OPERATIONAL AMPLIFIERS LM1A LM201A LM301A INPUT OFFSET VOLTAGE 0.7mV 2mV INPUT BIAS CURRENT 25nA 70nA INPUT OFFSET CURRENT 1.5nA 2nA SLEW RATE AS INVERSINGV/µs V/µs AMPLIFIER
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. LM392 Low Power Operational Amplifier/Voltage Comparator General Description
More informationNJU7046/NJU7047/NJU7048
NJU76/NJU77/NJU7 9V/μs High-Speed, Rail-to-rail I/O CMOS Operational Amplifier FEATURES (V + =V, V - =V, Ta= C) High Slew Rate 9V/µs Wide Bandwidth MHz Low Input Bias Current pa Rail-to-Rail Input and
More informationNJM13404 SINGLE SUPPLY DUAL OPERATIONAL AMPLIFIER 1 8 A
SINGLE SUPPLY DUAL OPERATIONAL AMPLIFIER GENERAL DESCRIPTION The is single-supply dual operational amplifier, which can operate from V supply. The features are low offset voltage, low bias current, high
More informationLF151 LF251 - LF351 WIDE BANDWIDTH SINGLE J-FET OPERATIONAL AMPLIFIER
LF151 LF251 - LF351 WIDE BANDWIDTH SINGLE J-FET OPERATIONAL AMPLIFIER INTERNALLY ADJUSTABLE INPUT OFFSET VOLTAGE LOW POWER CONSUMPTION WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW
More informationULTRA HIGH SPEED SINGLE OPERATIONAL AMPLIFIER
ULTRA HIGH SPEED SINGLE OPERATIONAL AMPLIFIER GENERAL DESCRIPTION The NJM711 is an ultra high speed single operational amplifier. It can swings 6V/µs high slew rate and 1GHz gain band width product(1mhz
More informationPrecision Operational Amplifier
Precision Operational Amplifier NJMOP77/NJMOP77 FEATURES Precision V IO =6μV max. V IO =μv max. (Ta= - to +8 ) PACKAGE OUTLINE Low Offset Drift V IO / T=.µV/ max. (Ta= - to +8 ) CMR db min. Low Noise V
More informationNJM4582 AUDIO DUAL OPERATIONAL AMPLIFIER
AUDIO DUAL OPERATIONAL AMPLIFIER GENERAL DESCRIPTION is the dual operational amplifier, specially designed for improving the tone control, which is most suitable for the audio application. Featuring noiseless,
More informationNJM5532 LOW-NOISE DUAL OPERATIONAL AMPLIFIER
LOW-NOISE DUAL OPERATIONAL AMPLIFIER NJM3 GENERAL DESCRIPTION The NJM3 is a high performance dual low noise operational amplifier. Compared to the standard dual operational amplifiers, such as the NJM,
More informationNJU High Output Current, Rail-to-Rail Input/Output Dual CMOS Operational Amplifier
High Output Current, Rail-to-Rail Input/Output Dual CMOS Operational Amplifier NJU779 GENERAL DESCRIPTION The NJU779 is a Rail-to-Rail input and output dual CMOS operational amplifier that features high
More informationTEB1033 TEF1033-TEC1033
TEB1033 TEF1033-TEC1033 PRECISION DUAL OPERATIONAL AMPLIFIERS VERY LOW INPUT OFFSET VOLTAGE : 1mV max. LOW DISTORTION RATIO LOW NOISE VERY LOW SUPPLY CURRENT LOW INPUT OFFSET CURRENT LARGE COMMON-MODE
More informationTL074. Low noise JFET quad operational amplifier. Features. Description
TL074 Low noise JFET quad operational amplifier Features Wide commonmode (up to V CC ) and differential voltage range Low input bias and offset current Low noise e n = 15 nv/ Hz (typ) Output shortcircuit
More informationUA748 PRECISION SINGLE OPERATIONAL AMPLIFIER
PRECISION SINGLE OPERATIONAL AMPLIFIER INPUT OFFSET VOLTAGE : 3mV max. OVER TEMPERATURE FREQUENCY COMPENSATION WITH A SINGLE 30pF CAPACITOR (C1) OPERATION FROM ±5V to ±15V LOW POWER CONSUMPTION : 50mW
More informationNJM2115 DUAL OPERATIONAL AMPLIFIER
NJM5 DUAL OPERATIONAL AMPLIFIER GENERAL DESCRIPTION NJM5 is a low operating Voltage ( ±.V min. ) and low saturation output voltage ( ±.V P-P at supply voltage ±.5V ) operational amplifier.it is applicable
More informationDual Precision Operational Amplifier
NJM79 Dual Precision Operational Amplifier FEATURES Precision V IO =6µV max. V IO =µv max. (Ta=-ºC to +8ºC) Low Offset Drift V IO / T=.9µV/ºC max. (Ta=-ºC to +8ºC) Specified for ±V and ±V operation CMR
More informationLM158-LM258-LM358. Low power dual operational amplifiers. Features. Description
-LM258-LM358 Low power dual operational amplifiers Features Internally frequency compensated Large DC voltage gain: 100 db Wide bandwidth (unity gain): 1.1 MHz (temperature compensated) Very low supply
More informationNJM2737. Low Noise, Rail-to-Rail Input/Output Dual Operational Amplifier
Low Noise, Rail-to-Rail Input/Output Dual Operational Amplifier GENERAL DESCRIPTION The NJM2737 is a Rail-to-Rail Input/Output single supply dual operational amplifier featuring low voltage operation,
More informationTL061 TL061A - TL061B
TL61 TL61A - TL61B LOW POWER J-FET SINGLE OPERATIONAL AMPLIFIERS VERY LOW POWER CONSUMPTION : µa WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGES LOW INPUT BIAS AND OFFSET CURRENTS OUTPUT
More informationLOW POWER QUAD OPERATIONAL AMPLIFIERS General Description. Features. Applications
General Description Features The consists of four independent, high gain and internally frequency compensated operational amplifiers. It is specifically designed to operate from a single power supply.
More informationNJM4580 DUAL OPERATIONAL AMPLIFIER
NJM8 DUAL OPERATIONAL AMPLIFIER GENERAL DESCRIPTION The NJM8 is a dual operational amplifier, specially designed for improving the tone control, which is most suitable for the audio application. Featuring
More informationTSV321-TSV358-TSV324. General Purpose, Input/Output Rail-to-Rail Low Power Operational Amplifiers. Description. Applications
General Purpose, Input/Output Rail-to-Rail Low Power Operational Amplifiers Operating at V CC = 2.5V to 6V Rail-to-rail input & output Extended V icm (V DD -.2V to V CC +.2V) Capable of driving a 32Ω load
More informationLM2904, LM2904A. Low-power dual operational amplifier. Features. Description
, A Low-power dual operational amplifier Features Internally frequency-compensated Large DC voltage gain: 100 db Wide bandwidth (unity gain): 1.1 MHz (temperature compensated) Very low supply current/amplifier,
More informationDesignated client product
Designated client product This product will be discontinued its production in the near term. And it is provided for customers currently in use only, with a time limit. It can not be available for your
More informationTSM100 SINGLE OPERATIONAL AMPLIFIER AND SINGLE COMPARATOR
OPERATIONAL AMPLIFIER LOW INPUT OFFSET VOLTAGE : 0.5 typ. MEDIUM BANDWIDTH (unity gain) : 0.9MHz LARGE OUTPUT VOLTAGE SWING : 0V to (V CC - 1.5V) INPUT COMMON MODE VOLTAGE RANGE INCLUDES GROUND WIDE POWER
More informationTL081 TL081A - TL081B
TL081 TL081A - TL081B GENERAL PURPOSE J-FET SINGLE OPERATIONAL AMPLIFIERS WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT OUTPUT SHORT-CIRCUIT PROTECTION
More informationTSV611, TSV611A, TSV612, TSV612A
TSV611, TSV611A, TSV612, TSV612A Rail-to-rail input/output 10 µa, 120 khz CMOS operational amplifiers Applications Datasheet - production data Out1 1 In1-2 In1+ 3 TSV611ILT - TSV611ICT In+ 1 5 V CC+ +
More informationTL074 TL074A - TL074B
A B LOW NOISE JFET QUAD OPERATIONAL AMPLIFIERS WIDE COMMONMODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT LOW NOISE e n = 15nV/ Hz (typ) OUTPUT SHORTCIRCUIT PROTECTION
More informationNJM8202. Single Supply, Rail-to-Rail Output Dual Operational Amplifier
NJM8 Single Supply, Rail-to-Rail Output Dual Operational Amplifier GENERAL DESCRIPTION The NJM8 is a Rail-to-Rail output single supply dual operational amplifier with a low noise of nv/ Hz (typ. at khz)
More informationLM158W, LM258W, LM358W
W, LM258W, LM358W Low power dual operational amplifiers Features Datasheet - production data N DIP8 (Plastic package) D and S SO8 and MiniSO8 (Plastic micropackage) P TSSOP8 (Thin shrink small outline
More informationMUSES8820. High Quality Audio Dual Operational Amplifier - + PACKAGE OUTLINE
MUSES High Quality Audio Dual Operational Amplifier GENERAL DESCRIPTION The MUSES is a high quality audio operational amplifier, which is optimized for high-end audio and professional audio applications.
More informationLow Noise, High-Speed Dual Operational Amplifier. Vni = 3nV/ Hz typ. (at f=10khz) ft = 90MHz typ. (at V + /V - = ±2.5V)
Low Noise, High-Speed Dual Operational Amplifier NJM2719 GENERAL DESCRIPTION The NJM2719 is a high speed voltage feedback dual operational amplifier specifically optimized for low voltage noise. Combining
More informationDual Operational Amplifier and Reference Regulator
Dual Operational Amplifier and Reference Regulator FP13 General Description The FP13 is a single chip composed of one independent OP-AMP (OPA2) and another OP-AMP (OPA1) with a 2.5V precision voltage reference
More informationTL062 TL062A - TL062B
TL62 TL62A TL62B LOW POWER JFET DUAL OPERATIONAL AMPLIFIERS VERY LOW POWER CONSUMPTION : µa WIDE COMMONMODE (UP TO + ) AND DIFFERENTIAL VOLTAGE RANGES LOW INPUT BIAS AND OFFSET CURRENTS OUTPUT SHORTCIRCUIT
More informationNon-inverting input 1. Part Number Temperature Range Package Packing Marking. 4558C MC4558CPT TSSOP8 Tape & Reel MC4558IN
Wide Bandwidth Dual Bipolar Operational Amplifier Internally compensated Short-circuit protection Gain and phase match between amplifier Low power consumption Pin-to-pin compatible with MC1458/LM358 Gain
More informationHigh Quality Audio, Bipolar Input, Dual Operational Amplifier
MUSES High Quality Audio, Bipolar Input, Dual Operational Amplifier The MUSES is a dual bipolar input high quality audio operational amplifier, which is optimized for high-end audio and professional audio
More informationDual Operational Amplifiers
FEATURES Wide range of supply voltages Low supply current drain independent of supply voltage Low input biasing current Low input offset voltage and offset current Input common-mode voltage range includes
More informationTL082 TL082A - TL082B
TL082 TL082A - TL082B GENERAL PURPOSE J-FET DUAL OPERATIONAL AMPLIFIERS WIDE COMMON-MODE (UP TO V + CC ) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT OUTPUT SHORT-CIRCUIT PROTECTION
More informationLM158/LM258/LM358/LM2904 Low Power Dual Operational Amplifiers
Low Power Dual Operational Amplifiers General Description The LM158 series consists of two independent, high gain, internally frequency compensated operational amplifiers which were designed specifically
More informationLM158, LM258, LM358, LM158A, LM258A, LM358A
LM158, LM258, LM358, LM158A, LM258A, Low-power dual operational amplifiers Datasheet - production data Related products See LM158W for enhanced ESD ratings See LM2904 and LM2904W for automotive grade versions
More informationLM124/LM224/LM324/LM2902 Low Power Quad Operational Amplifiers
Low Power Quad Operational Amplifiers General Description The LM124 series consists of four independent, high gain, internally frequency compensated operational amplifiers which were designed specifically
More informationNE/SA/SE532 LM258/358/A/2904 Low power dual operational amplifiers
INTEGRATED CIRCUITS NE/SA/SE53 Supersedes data of Jan Jul 1 DESCRIPTION The 53/358/LM94 consists of two independent, high gain, internally frequency-compensated operational amplifiers internally frequency-compensated
More informationTSM104W/A QUAD OPERATIONAL AMPLIFIER AND PROGRAMMABLE VOLTAGE REFERENCE OPERATIONAL AMPLIFIERS
TSM14W/A QUAD OPERATIONAL AMPLIFIER AND PROGRAMMABLE VOLTAGE REFERENCE OPERATIONAL AMPLIFIERS LOW SUPPLY CURRENT : 375µA/op. (@ V CC = 5V) LOW INPUT BIAS CURRENT : 2nA MEDIUM SPEED :.9MHz LOW INPUT OFFSET
More informationTS522. Precision low noise dual operational amplifier. Features. Description
Precision low noise dual operational amplifier Datasheet production data Features Large output voltage swing: +14.3 V/-14.6 V Low input offset voltage 850 μv max. Low voltage noise: 4.5 nv/ Hz High gain
More informationPrecision Operational Amplifier
Precision Operational Amplifier NJM79 FEATURES Precision V IO =6µV max. V IO =µv max. (Ta=-ºC to +8ºC) Low Offset Drift ΔV IO /ΔT=.9µV/ºC max. (Ta=- to +8ºC) Specified for ±V and ±V operation CMR db min.
More informationNJM12904L SINGLE SUPPLY DUAL AMPLIFIER
NJM9 SINGLE SUPPLY DUAL AMPLIFIER GENERAL DESCRIPTION The NJM9 is single-supply dual operational amplifier, which can operate from V supply. The features are low offset voltage, low bias current, and drive
More informationLM158, LM258, LM358. Low-power dual operational amplifiers. Features. Description
, LM258, LM358 Low-power dual operational amplifiers Datasheet production data Features Internally frequency-compensated Large DC voltage gain: 1 db Wide bandwidth (unity gain): 1.1 MHz (temperature compensated)
More information