Manual of ELMB_MB v modifications for technicians.
|
|
- Avis James
- 6 years ago
- Views:
Transcription
1 ELMB_MB_v6.5.2_manual.doc 1/10 Manual of ELMB_MB v modifications for technicians. B. Palan, A. Tikhonov, A. Solin Date: 10 Jan 2007 Pages: 10 Summary: This document describes the component changes of LVPS ELMB_MB from produced version 6.5 into new version All mentioned component names and values are referring to the scheme components designed by Ivan Hruska of ELMB_MB version 6.5. In addition to previously discussed ELMB_MB version 6.5.1, new modifications were added in the section describing the improvements of five TileCal Drawer sense lines measurements: +3VDIG, +5VDIG, -5VMB, +5VMB, +15VMB (Part 3 of this document). 1. Short eight resistors R Put zero ohm resistors (to minimize Start-up pulse dependency on Vout of the brick). Fig.1: Top side photo of ELMB_MBv6.5. Remove 8x 10Ohm resistors (R129 R136 marked in red color), short-cut them by a piece of wire, or put zero ohm resistors (size 1206).
2 ELMB_MB_v6.5.2_manual.doc 2/10 2. Remove C119, C99, C109, C129, C89, C61, C45, C79 (size 0603) on top side. Due to unconnected one temperature measurements of each brick the corresponding floating capacitors on the ELMB_MB are removed. Fig.2: Top side photo and details of ELMB_MBv6.5. Remove 8x 100nF capacitors: C119, C99, C109, C129, C89, C61, C45, C79, marked in red color (size 0603).
3 ELMB_MB_v6.5.2_manual.doc 3/10 3. Improvement of five drawer sense line measurements: +3VDIG, +5VDIG, -5VMB, +5VMB, +15VMB. See further ELMB_MB scheme detail on page 8, Fig.11 for more information. (a) (b) Cut +5VMB pcb trace from pin5 on connector J12 on the ELMB_MB bottom side, see Fig.3. The pcb trace is under the surface level, so a milling cutter has to be used. Cut two traces, between R27 and pin1 of U7 isolation amplifier, and pcb path between R27 and pin8 of opamp U13, see Fig.3, 4. (a) Pin5 U12 (d) Pin1 (c) U13 U7 (b) R27 Fig.3: Bottom side photos of ELMB_MBv6.5. Cutting traces on bottom side. (c) Cut trace between pin3 and pin4 of U12 isolation amplifier, see Fig.3, 4. (d) Cut trace going to gnd from C22 and R38, see Fig.3, 4.
4 ELMB_MB_v6.5.2_manual.doc 4/10 Fig.4: Bottom side component placement detail of ELMB_MBv6.5, as shown as a photo in Fig 3. Marked components related to procedure 3 a d are in red color: U13, C22, R38, R27, U12, and U7. Verify cut traces (3 a - d) by measuring 3 points, see Fig.5. (I) Check non-zero resistance between pin5 (J12) and pin1 of U12. (II) Measure non-zero resistance between pin8 of U13 and R27. (III) Measure non-zero resistance between R27 and pin1 of U7. (IV) Measure non-zero resistance between pin3 and pin4 of U12. (I) U12 (IV) U13 (II) U7 Fig.5. Measuring points of successful cuts 3 a - d. (III)
5 ELMB_MB_v6.5.2_manual.doc 5/10 (e) Unsolder opamp U13, resistor R39, R40, and capacitor C23. Unsolder also Transil D5, see Fig.6. Fig.6. Unsoldered components from bottom side ELMB_MBv6.5 related to point 3-e. (f) Nominal resistor values of ELMB_MB input sense line dividers have been changed, see scheme on page 8 and Fig.11. New resistor values are: R11, R20, R28, R32, R38 = 200 ohm R10 = 10k, R19 = 16k, R27 = 15k, R31 = 47k, R37 = 15k, soldered in diagonal to other end of C22 capacitor, see detail in Fig 8. These modifications were applied to reduce the influence of 1kOhm (1%) separating resistors (inside Drawer) on the ELMB_MB sense lines measurements. Resistor R37 is soldered
6 ELMB_MB_v6.5.2_manual.doc 6/10 Fig.7. Resistor dividers to be changed on ELMB_MB bottom side. R37 Fig.8. Detail picture how to solder resistor R37 in diagonal to the opposite end of C22 capacitor. (g) Resistor R27 (part of +5VMB sense line divider) connect directly to pin5 of J12 connector by a 30mm piece of wire, see Fig.9.
7 ELMB_MB_v6.5.2_manual.doc 7/10 (h) (g) (i) (j) (h) (i) (j) (k) Fig.9. Wire connections on bottom side 3-g, h, i, j. Connect pin3 of J12 with pin1 of U12 by using a wire, see Fig.9. This operation will connect +5V DIG with power supplies of all five isolation amplifiers (HCP7840). Make a short connection between pin4 and pin 2 of U12, see Fig.9. Connect resistor R37 directly to pin7 of the connector J12 (-5VMB sense lines) by means of short-cut through unsoldered components C23, R40, see Fig.9. Verify good connection between pin7 of J12 and resistor R37. Solder ceramic capacitors 10uF (size 1210) between pin2 and pin3 of all isolation amplifiers on bottom side of U1, U3, U7, U10, U12, to increase the nominal filtering capacitor values of C11, C13, C17, C19, C22, see Fig.10. Fig.10. Ceramic capacitors on U1, U3, U7, U10, U12, and capacitor 68uF/20V in place of D5 transil. (l) Solder tantalum capacitor 68uF/20V in the place of removed transil diode D5. Positive polarity has to be towards pin3 of J12 connector, see Fig.10.
8 ELMB_MB_v6.5.2_manual.doc 8/10 Appendix1: Sense line part with isolation amplifiers of the ELMB_MBv6.5 electrical scheme discussed in part 3. Fig.11: Part of the MB_ELMB V6.5 schematic documentation. Changes of sense line optocouplers powering do +5VDIG line, changing of resistor dividers for all sense lines. All changes are drawn in red color.
9 ELMB_MB_v6.5.2_manual.doc 9/10 Appendix2: Component placement on the ELMB_M Bv6.5, top and bottom side.
10 ELMB_MB_v6.5.2_manual.doc 10/10
Manual of ELMB_MB v modifications for technicians.
ELMB_MB_v6.5.3_manual.doc 1/11 Manual of ELMB_MB v.6.5.3 modifications for technicians. B. Palan, A. Tikhonov Date: 14 Feb 2007 bpalan@cern.ch Pages: 11 Summary: This document describes the component changes
More informationUM1360 Evaluation Board User s Guide
UM1360 Evaluation Board User s Guide Version Date Provider Approve Note 1.0 2012-11-02 LB Initial version. Table of Contents 1. Board Information 1.1 Schematic 1.2 PCB Layout 1.3 Jumper and Test Point
More informationPacific Antenna - Easy TR Switch
Pacific Antenna - Easy TR Switch Kit Description The Easy TR Switch is an RF sensing switch that can be used to switch an antenna between a receiver and transmitter. It also has a second switched pair
More informationPacific Antenna Easy TR Switch
Pacific Antenna Easy TR Switch Kit Description The Easy TR Switch is an RF sensing circuit with a double pole double throw relay that can be used to automatically switch an antenna between a separate receiver
More informationFROM SCHEMATIC TO VEROBOARD
FROM SCHEMATIC TO VEROBOARD The circuit of a bench amplifier utilising a LM386 linear (integrated circuit) IC and a few other components is used for this tutorial. The schematic is shown below: First a
More informationBeta-test ED1 PCB installed in I0CG s K1
K1 SSB Modification (Ed.2) This description provides the receiver (RX) modifications, assembly, alignment and operation as a first step. In a second step you can add the remaining transmitter (TX) modifications,
More informationS Flexible Input and Output Configurations S Single 2.7V to 5.5V Power Supply S Fully Assembled and Tested
19-5087; Rev 0; 12/09 MAX4231 Evaluation Kit General Description The MAX4231 evaluation kit (EV kit) is a fully assembled and tested PCB that evaluates the MAX4231 single, high-output-drive CMOS operational
More informationPI3DPX1207B Layout Guideline. Table of Contents. 1 Layout Design Guideline Power and GROUND High-speed Signal Routing...
PI3DPX1207B Layout Guideline Table of Contents 1 Layout Design Guideline... 2 1.1 Power and GROUND... 2 1.2 High-speed Signal Routing... 3 2 PI3DPX1207B EVB layout... 8 3 Related Reference... 8 Page 1
More informationMain improvements are increased number of LEDs and therefore better temperature indication with one Celsius degree increments.
LED Thermometer V2 (Fahrenheit/Celsius/±1 ) PART NO. 2244754 After completing this great starter kit, users will have a nice interactive LED thermometer. You will learn one principle how temperature can
More informationDIY Function Generator XR2206
DIY Function Generator XR2206 20Hz 100KHz http://radiohobbystore.com Components List: Resistors: R1, R2 1% Metal Film 5K1 R4 1% Metal Film 10K R5 1% Metal Film 3K R10 5% Carbon Film 10R R3, R9 Potentiometer
More informationPenrose Quantizer Assembly Guide
Penrose Quantizer Assembly Guide Schematic and BOM The schematic can be found here: www.sonic-potions.com/public/penrosequantizerschematic.pdf The BOM is available at google docs: Link to BOM Prepare the
More informationTotal solder points: 82 Difficulty level: beginner advanced. Dc to Pulse Width Modulator K8004 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 82 Difficulty level: beginner 1 2 3 4 5 advanced Dc to Pulse Width Modulator K8004 Allows very efficient control of DC motors, heaters or lights. ILLUSTRATED ASSEMBLY MANUAL H8004IP-2
More informationManual Version July 2007
Manual Version 1.2 - July 2007 Page 1 Table of Contents Section1: M3 Phono Board Build...3 Phono Board Parts List...3 Preparation...4 Fitting the Valve Bases...6 Installing the Resistors...7 Starting the
More informationLab 4 - Operational Amplifiers 1 Gain ReadMeFirst
Lab 4 - Operational Amplifiers 1 Gain ReadMeFirst Lab Summary There are three basic configurations for operational amplifiers. If the amplifier is multiplying the amplitude of the signal, the multiplication
More informationWJ-8617B and WJ-8618B HF Upgrades: 500 KHz to 1100 MHz By: Stephen Pappin
WJ-8617B and WJ-8618B HF Upgrades: 500 KHz to 1100 MHz By: Stephen Pappin The typical frequency coverage for an 8617B or 8618B is from 20 MHz to 1100 MHz (500 MHz without FE). These versions have pre selectors
More information23V, 3A, 340KHz Synchronous Step-Down DC/DC Converter
23V, 3A, 340KHz Synchronous Step-Down DC/DC Converter Description The is a synchronous step-down DC/DC converter that provides wide 4.5V to 23V input voltage range and 3A continuous load current capability.
More informationS-Pixie QRP Kit. Student Manual. Revision V 1-0
S-Pixie QRP Kit Student Manual Revision V 1-0 Introduction The Pixie 2 is a small, versatile radio transceiver that is very popular with QRP (low power) amateur radio operators the world over. It reflects
More informationKK1L Icom Band Decoder Basic Assembly
KK1L Icom Band Decoder Basic Assembly Ronald Rossi, KK1L http://home.comcast.net/~kk1l Features: RFI isolated inputs Fully opto-isolated Replaces one BCD band decode port on KK1L dual decoder Description:
More information12V Dimmer Kit, version 2
12V Dimmer Kit, version 2 User Manual Description The 12V Dimmer Kit V2 is an especially efficient PWM (pulse-width modulation) controller for 12V loads up to 60 watts. It features a single dial control
More information3. Assembly manual ANALYZING THE PCB'S LCD PCB. Component side: Solder side:
3. Assembly manual ANALYZING THE PCB'S LCD PCB Component side: Solder side: MAIN PCB Component side: Solder side: ASSEMBLGING THE LCD PCB 1. Resistor R1: 33 Ohm (orange, black, black) 2. 6 Pin female header
More informationRC Servo Interface. Figure Bipolar amplifier connected to a large DC motor
The bipolar amplifier is well suited for controlling motors for vehicle propulsion. Figure 12-45 shows a good-sized 24VDC motor that runs nicely on 13.8V from a lead acid battery based power supply. You
More informationElectronic Components
Electronic Components Arduino Uno Arduino Uno is a microcontroller (a simple computer), it has no way to interact. Building circuits and interface is necessary. Battery Snap Battery Snap is used to connect
More informationPacific Antenna Easy SWR Indicator Kit
Pacific Antenna Easy SWR Indicator Kit Description Monitoring the match of an antenna to your transmitter or adjusting an antenna tuner for best match requires an indicator of the reflected power as an
More informationMaterials. Eight pin DIP socket 0.1 µf capacitor
JOE GROELE Project Outline The goal of this project was to build a plasma speaker that will amplify an electric guitar sound. Build an audio oscillator circuit using an ordinary speaker Test speaker performance
More informationAmplifier, Product Design
Amplifier, Product Design Choose one component from the amplifier circuit and investigate technical, theory and mathematical information related to your chosen component. This work will be completed over
More informationPurpose. Table of Contents. Purpose...1. Introduction...2. General Product Information...2. Key Performance Summary Table...3
Purpose The RT8008 is a high-efficiency 1.5MHz current mode synchronous step-down regulator that can deliver up to 600mA output current from an input voltage range of 2.5V to 5.5V. This document explains
More information1 Introduction External Component Requirements AC Coupling Capacitors on high speed lanes... 2
PI3TB212 PI3TB212 Thunderbolt Application Information Table of Contents 1 Introduction... 2 2 External Component Requirements... 2 2.1 AC Coupling Capacitors on high speed lanes... 2 2.2 Pull-down Resistor
More informationV-TUNE. Variable capacitance mini-circuit with Varactor diode and potentiometer control. Assembly manual. Last updated: July 15, 2017
V-TUNE Variable capacitance mini-circuit with Varactor diode and potentiometer control Assembly manual Last updated: July 15, 2017 ea3gcy@gmail.com Updates and news at: www.ea3gcy.com Thanks for building
More informationDIY KIT 141. Multi-Mode Timer
INTRODUCTION No one can call themselves an electronics hobbyist unless they have built a timer. There are many tens of designs using a variety of new and sometimes old circuits. Witness the longest surviving
More information400W MONO/STEREO AMPLIFIER
400W MONO/STEREO AMPLIFIER Universal, robust and compact are the words to describe this amplifier. Total solder points: 264 Difficulty level: beginner 1 2 3 4 5 advanced K4005B ILLUSTRATED ASSEMBLY MANUAL
More informationACT111A. 4.8V to 30V Input, 1.5A LED Driver with Dimming Control GENERAL DESCRIPTION FEATURES APPLICATIONS TYPICAL APPLICATION CIRCUIT
4.8V to 30V Input, 1.5A LED Driver with Dimming Control FEATURES Up to 92% Efficiency Wide 4.8V to 30V Input Voltage Range 100mV Low Feedback Voltage 1.5A High Output Capacity PWM Dimming 10kHz Maximum
More informationQUASAR PROJECT KIT # /24 HOUR GIANT CLOCK
This project was originally published in the electronics magazine, Silicon Chip, a few years ago. It is issued here as a kit with permission. Some modifications to the original published circuit and software
More informationSSRP LTC1746 Assembly Manual V0.1 Check the most recent version
SSRP LTC1746 Assembly Manual V0.1 Check the most recent version http://oscar.dcarr.org/ssrp/hardware/ltc1746/ltc1746.php Introduction This manual details the general assembly process for the SSRP LTC1746
More informationCustomer Service Bulletin SD Upgrade to SLP45400 Low Voltage/High Voltage Power Supply PCB
Customer Service Bulletin SD800003 Upgrade to SLP45400 Low Voltage/High Voltage Power Supply PCB Continual Improvement is a cornerstone of the Southern Avionics Company Quality Management System. We issue
More informationPurpose. Table of Contents. Purpose Introduction General Product Information Key Performance Summary Table... 3
Purpose The RT8295A is a high-efficiency current mode synchronous step-down regulator that can deliver up to 2A output current from a wide input voltage range of 4.5V to 23V. This document explains the
More informationPacific Antenna Easy Transmitter Kit
Pacific Antenna Easy Transmitter Kit Introduction The Easy Transmitter kit from qrpkits.com provides a crystal controlled transmitter with VXO tuning. The circuit consists of a N3904 based crystal oscillator
More informationDiscrete Op-Amp Kit MitchElectronics 2019
Discrete Op-Amp Kit MitchElectronics 2019 www.mitchelectronics.co.uk CONTENTS Introduction 3 Schematic 4 How It Works 5 Materials 9 Construction 10 Important Information 11 Page 2 INTRODUCTION Even if
More informationBROADBAND DISTRIBUTED AMPLIFIER
ADM-126-83SM The ADM-126-83SM is a broadband, efficient GaAs PHEMT distributed amplifier with an integrated bias tee in a 4mm QFN surface mount package, designed to provide efficient LO drive for T3 mixers.
More informationGaAs MMIC devices are susceptible to Electrostatic Discharge. Use proper ESD precautions when handling these items.
The is a broadband, power efficient GaAs PHEMT distributed amplifier in a 4mm QFN surface mount package. The is designed to provide optimal LO drive for T3 mixers. Typically, ADM-26-2931SM provides. db
More informationFROM: Apply +15V to the HV SAMPLE terminal on the self-resonant board. Verify that the red LED, D6 (HV Charge) is illuminated on the display board.
The following document outlines the known errors and omissions in the minibrute DRSSTC design. These include both the book, DRSSTC: Building the Modern Day Tesla Coil minibrute Reference Design as well
More informationTFT-LCD DC/DC Converter with Integrated Backlight LED Driver
TFT-LCD DC/DC Converter with Integrated Backlight LED Driver Description The is a step-up current mode PWM DC/DC converter (Ch-1) built in an internal 1.6A, 0.25Ω power N-channel MOSFET and integrated
More informationTKEY-1. CW touch key. (no electromechanical contacts) Assembly manual. Last update: May 1,
TKEY-1 CW touch key (no electromechanical contacts) Assembly manual Last update: May 1, 2016 ea3gcy@gmail.com Updates and news at: www.qsl.net/ea3gcy Thanks for constructing the TKEY-1A CW touch key Have
More informationLow Power GaAs MMIC Double Balanced Mixer. Refer to our website for a list of definitions for terminology presented in this table.
Low Power GaAs MMIC Double Balanced Mixer MM1-0212LSM 1. Device Overview 1.1 General Description The MM1-0212LSM is a low power GaAs MMIC double balanced mixer that operates at LO powers as a low as +1
More informationCC2 Charge Sensitive Preamplifier: Experimental Results and Ongoing Development
GERDA Meeting at LNGS - 2 / 2010 CC2 Charge Sensitive Preamplifier: Experimental Results and Ongoing Development Stefano Riboldi, Alessio D Andragora, Carla Cattadori, Francesca Zocca, Alberto Pullia Starting
More informationBassAce - Midi Bass Synthesizer. BassAce Features
Untitled Document BassAce - Midi Bass Synthesizer The BassAce is a small midi-synth based loosely on the TB303. It can be built many different ways. Depending on how it's configured it can be anything
More information16 Bit Micro Experimenter Assembly and Check out Instructions
16 Bit Micro Experimenter Assembly and Check out Instructions The kit you purchased that includes PCB, schematic, complete parts list and these assembly instructions. A top picture of the complete assembly
More informationTransistor Flasher Kit MitchElectronics 2018
Transistor Flasher Kit MitchElectronics 2018 www.mitchelectronics.co.uk CONTENTS Introduction 3 Schematic 4 How It Works 5 Materials 6 Construction 7 Important Information 8 Page 2 INTRODUCTION In electronics
More informationModel FL8300 SERVICE MANUAL. harman/kardon. 5 Disc Compact Disc Changer CONTENTS
harman/kardon Model FL8300 5 Disc Compact Disc Changer SERVICE MANUAL CONTENTS LASER BEAM SAFETY PRECAUTIONS...2 OTHER PRECAUTIONS...... 3 LEAKAGE TEST....... 4 SPEClFlCATlONS......... 5 CONTROL AND FUNCTIONS......
More informationPI3HDMI1210(-A) PI3HDMI1210-A Demo Board Rev.A User Manual
PI3HDMI1210(-A) PI3HDMI1210-A Demo Board Rev.A User Manual Introduction This user manual describes the components and the usage of PI3HDMI1210(-A) demo Board Rev.A. Figure 1: Top View of PI3HDMI1210-A
More informationPrecision Switchable Vout Regulator for OTP Applications
Precision Switchable Vout Regulator for OTP Applications Preliminary Technical Data FCDC 00159 FEATURES Output Voltage Switchable between 2.5V 2% and 7.0V 1% Output Current: 0 to 50 ma Input voltage: 3.2
More informationBalanced Modulator. Model 9748 Assembly and Using Manual PAiA Corporation
Balanced Modulator Model 9748 Assembly and Using Manual This second-generation 9700-series processing element for modular sound synthesizers is designed to provide great sound and excellent value. Audio
More informationSMT Module RF Reference Design Guide. AN_ SMT Module RF Reference Design Guide _V1.01
SMT Module RF Reference Design Guide AN_ SMT Module RF Reference Design Guide _V1.01 Document Title: SMT Module RF Reference Design Guide Version: 1.01 Date: 2010-2-10 Status: Document Control ID: Release
More informationS Rail-to-Rail Inputs/Outputs S Accomodates Easy-to-Use 0805 Components S Proven PCB Layout S Fully Assembled and Tested
9-590; Rev 0; /0 MAX96 Evaluation Kit General Description The MAX96 evaluation kit (EV kit) provides a proven design to evaluate the MAX96 low-power, MOS-input operational amplifier (op amp) in a 6-pin
More informationControl System Circuits with Opamps
Control System Circuits with Opamps 27.04.2009 Purpose To introduce opamps, transistors and their usage To apply a control system with analog circuit elements. Difference Amplifier Figure 1 Basic Difference
More informationBill of Materials: Metronome Kit PART NO
Metronome Kit PART NO. 2168325 The metronome kit allows you to build your own working electronic metronome. Features include a small speaker, flashing LED, and the ability to switch between several different
More information2.2A Step-Down Converter BM1410A
2.2A Step-Down Converter BM40A FEATURES 2.2A Output Current Efficiency up to 92% @+5V output +5V to +23V Input Range 5µA Shutdown Supply Current 380kHz Switching Frequency Adjustable Output Voltage from.23v
More informationIS31BL3506B 1.0MHZ BOOST CONVERTER WITH 35V INTERNAL MOSFET SWITCH
ISBL0B.0MHZ BOOST CONVERTER WITH V INTERNAL MOSFET SWITCH DESCRIPTION ISBL0B is a boost converter featuring an integrated MOSFET switch designed for driving series strings of LED or other device. Input
More informationB-Series Fast, Blue-Sensitive Silicon Photomultiplier Sensors
B-Series: Fast, Blue-Sensitive Silicon Photomultiplier Sensors Overview B-series Silicon Photomultipliers (SiPM) offer the highest PDE, UV sensitivity and are available with SensL s proprietary fast mode
More informationGaAs MMIC devices are susceptible to Electrostatic Discharge. Use proper ESD precautions when handling these items.
ADM-26-931SM The ADM-26-931SM is a broadband, power efficient GaAs PHEMT distributed amplifier in a 4mm QFN surface mount package. The ADM-26-931SM is designed to provide optimal LO drive for T3 mixers.
More informationUser s Manual ISL71218MEVAL1Z. User s Manual: Evaluation Board. High Reliability Space
User s Manual ISL71218MEVAL1Z User s Manual: Evaluation Board High Reliability Space Rev. Aug 217 USER S MANUAL ISL71218MEVAL1Z Evaluation Board UG139 Rev.. 1. Overview The ISL71218MEVAL1Z evaluation platform
More informationGaAs MMIC devices are susceptible to Electrostatic Discharge. Use proper ESD precautions when handling these items.
ADM-26-929SM The ADM-26-929SM is a broadband, efficient GaAs PHEMT distributed amplifier in a 4mm QFN surface mount package. It is designed to provide optimal LO drive for T3 mixers and offers 13 db typical
More informationSimple LFO Features. 2. Application. 3. Description. Simple and easy to build LFO module for Analog Synthesizers.
Simple LFO. Simple and easy to build LFO module for Analog Synthesizers.. Features Square and Triangle waveforms (90 phase shifted) Dual range frequencies Frequency ranges from under Hz up to several khz
More informationGaAs MMIC devices are susceptible to Electrostatic Discharge. Use proper ESD precautions when handling these items.
ADM-12-931SM The ADM-12-931SM is a small, low power, and economical T3 driver or T3A pre-amplifier. It is a GaAs PHEMT distributed amplifier in a 3mm QFN surface mount package. The ADM-12-931SM can provide
More informationFEATURES. Rst1 R Rst2 C2 R2
DESCRIPTION is a high precision LED constant current control chip operating at critical conduction mode (CRM) with zero current switched-on and peak current switched-off. It s mainly targeted for non-isolated
More informationPI3USB102 PI3USB102 Demo Board Rev.A User Manual
PI3USB102 PI3USB102 Demo Board Rev.A User Manual Introduction This user manual describes the components and operation of the PI3USB102 Demo Board. USB2.0 high-speed, fullspeed and low speed signal quality
More informationSC Series. SC Series High Voltage Power Supply
High Voltage Power Supply General Description The high voltage power supplies are the workhorse of the high voltage industry. They provide isolated outputs of up 9kV and 10 Watts in power (depending on
More information555 Astable Kit MitchElectronics 2018
555 Astable Kit MitchElectronics 2018 www.mitchelectronics.co.uk CONTENTS Introduction 3 Schematic 3 How It Works 4 Materials 6 Construction 7 Important Information 8 Page 2 INTRODUCTION The 555 timer
More informationTD-DEV V Technical Specification
High-Efficiency MODULE Carrier Board TD-DEV-500-12V Technical Specification POWER SUPPLY TECHNOLOGY FEATURES Low profile 1U, 500W power supply High efficiency power supply Fully integrated with CPU control
More informationDTMF decoder kit with 8 outputs and Morse transpond. 8 output DTMF decoder with 4 on board BT47 style 12V relays and 4 open collector outputs
DJS Electronics Ltd cstech.co.uk DTMF decoder kit with 8 outputs and Morse transpond Features 8 output DTMF decoder with 4 on board BT47 style 12V relays and 4 open collector outputs Each output can be
More informationDUAL STEPPER MOTOR DRIVER
DUAL STEPPER MOTOR DRIVER GENERAL DESCRIPTION The is a switch-mode (chopper), constant-current driver with two channels: one for each winding of a two-phase stepper motor. is equipped with a Disable input
More information100 VOLT 10 AMP RAD-HARD H-BRIDGE PWM MOTOR DRIVER/AMPLIFIER Dey Road Liverpool, N.Y (315)
MIL-PRF-38534 CERTIFIED M.S.KENNEDY CORP. 100 VOLT 10 AMP RAD-HARD 4204RH H-BRIDGE PWM MOTOR DRIVER/AMPLIFIER 4707 Dey Road Liverpool, N.Y. 13088 (315) 701-6751 FEATURES: Total Dose Hardened To TBD Krad(Si)
More informationSTARTER / GENERATOR MOTOR CONTROLLER
MIL-PRF-38534 AND 38535 CERTIFIED FACILITY M.S.KENNEDY CORP. STARTER / GENERATOR MOTOR CONTROLLER 4413 (315) 701-6751 FEATURES: 28V/160A Brushless DC motor control capability. 28V/90A Synchronous Boost
More information3 phase bridge driver IC TLE7183F
Application Note Rev 2.0, 2012-03-30 Automotive Power Abstract 1 Abstract Note: The following information is given as a hint for the implementation of the device only and shall not be regarded as a description
More informationBi-Directional DC Motor Speed Controller 5-32Vdc (3166v2)
General Guidelines for Electronic Kits and Assembled Modules Thank you for choosing one of our products. Please take some time to carefully read the important information below concerning use of this product.
More informationData Conversion and Lab Lab 1 Fall Operational Amplifiers
Operational Amplifiers Lab Report Objectives Materials See separate report form located on the course webpage. This form should be completed during the performance of this lab. 1) To construct and operate
More informationELEC3106 Electronics. Lab 3: PCB EMI measurements. Objective. Components. Set-up
ELEC3106 Electronics Lab 3: PCB EMI measurements Objective The objective of this laboratory session is to give the students a good understanding of critical PCB level Electromagnetic Interference phenomena
More informationGaAs MMIC Double Balanced Mixer. Description Package Green Status
GaAs MMIC Double Balanced Mixer MM1-0212SSM 1. Device Overview 1.1 General Description The MM1-0212SSM is a highly linear GaAs MMIC double balanced mixer. MM1-0212SSM is a low frequency, high linearity
More informationZA3020LV 2A Step-Down,PWM,Switch-Mode DC-DC Regulator
General Description The is a monolithic step-down switch-mode regulator with internal Power MOSFETs. It achieves 2A continuous output current over a wide input supply range with excellent load and line
More informationMLX83100 Automotive DC Pre-Driver EVB83100 for Brushed DC Applications with MLX83100
EVB83100 for Brushed DC Applications with MLX83100 Stefan Poels JULY 17, 2017 VAT BE 0435.604.729 Transportstraat 1 3980 Tessenderlo Phone: +32 13 67 07 95 Mobile: +32 491 15 74 18 Fax: +32 13 67 07 70
More informationNovember 2013 Rev VIN FDMS7578. L1 IHLP-5050FD-01 41A, 1mOhm. Csnub 0 Ohm FDMS7650DC. 0 Ohm. 6.8nF. CFF 0.56nF
XRP64 November 0 Rev..0.0 GENERAL DESCRIPTION The XRP64 is a synchronous step-down controller for point-of load supplies up to 5A. A wide 4.5V to V input voltage range allows for single supply operation
More informationHow to build a Cracklebox. Red Wierenga Brooklyn College Center for Computer Music October 13, 2015
How to build a Cracklebox Red Wierenga Brooklyn College Center for Computer Music October 13, 2015 What s a Cracklebox? What s a Cracklebox? The Cracklebox was developed by Michel Waisvisz and others at
More informationQUICK START GUIDE FOR DEMONSTRATION CIRCUIT 804 POWER OVER ETHERNET PD INTERFACE WITH INTEGRATED SWITCHING REGULATOR
DESCRIPTION LTC4267 Demonstration circuit 804 is a POWER OVER ETHERNET PD INTERFACE WITH INTEGRATED SWITCHING REGULATOR featuring the LTC4267. It provides a complete IEEE 802.3af power device (PD) interface
More informationAMS2115 FAST TRANSIENT RESPONSE LDO CONTROLLER
FAST TRANSIENT RESPONSE LDO CONTROLLER General Description The AMS5 is a single IC controller that drives an external N Channel MOSFET as a source follower to produce a fast transient response, low dropout
More informationassembly instructions OPENAMP1 Assembly instructions and manual All rights reserved 27/12/ Pavel MACURA
OPENAMP1 Assembly instructions and manual 27/12/2012 1 Pavel MACURA 1. Introduction OPENAMP1 is a preamplifer for MM phono cartridge. It uses operational amplifiers, a monolithic buffer and a feedback
More informationBMC055. Sallen-Key Voltage Controlled Filter Last updated
BMC055. Sallen-Key Voltage Controlled Filter Last updated 0-6-208 If you have any questions, or need help trouble shooting, please e-mail Michael@Bartonmusicalcircuits.com I What The Knobs And Jacks Do
More informationAN1489 Application note
Application note VIPower: non isolated power supply using VIPer20 with secondary regulation Introduction Output voltage regulation with adjustable feedback compensation loop is very simple when a VIPer
More informationFeatures. = +25 C, 50 Ohm System, Vcc= 5V
Typical Applications Prescaler for 1 MHz to 13 GHz PLL Applications: Point-to-Point / Multi-Point Radios VSAT Radios Fiber Optic Test Equipment Space & Military Functional Diagram Features Ultra Low ssb
More informationLine Following Circuit Board Wiring Guide
Line Following Circuit Board Wiring Guide Soldering the Analog Optosensors 1. Obtain a line following printed circuit board from the store as well as three analog optosensors (w/6 resistors). 2. Remove
More informationTotal solder points: 79 Difficulty level: beginner advanced GUITAR PREAMPLIFIER WITH HEADPHONE OUTPUT K4102 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 79 Difficulty level: beginner 1 2 3 4 5 advanced GUITAR PREAMPLIFIER WITH HEADPHONE OUTPUT K4102 Practice the guitar without disturbing others. ILLUSTRATED ASSEMBLY MANUAL H4102IP-1
More information5A 300KHz 32V Buck DC to DC Converter
Features Wide 5V to 32V Input Voltage Range Output Adjustable from 0.8V to 30V Maximum Duty Cycle 100% Minimum Drop Out 0.6V Fixed 300KHz Switching Frequency 5A Constant Output Current Capability Internal
More informationSoftRock v5.0 Builder s Notes. December 12, Building a QSD Kit
SoftRock v5.0 Builder s Notes December 12, 2005 Building a QSD Kit Be sure to use a grounded tip soldering iron in building the QSD board. The soldering iron needs to have a small tip, (0.05-0.1 inch diameter),
More informationSERVICE MANUAL PROJECT TWELVE MONO POWER AMPLIFIER
1. SERVICE MANUAL PROJECT TWELVE MONO POWER AMPLIFIER Contents 1. UNPACKING...3 2. SPHINX WARRANTY CARD...3 3. CONTACTING THE MANUFACTURER...3 4. THE POWER AMP AT A GLANCE...4 Front panel... 4 Rear panel...
More information+Denotes lead(pb)-free and RoHS compliant.
19-4552; Rev 0; 4/09 MAX9918 Evaluation Kit General Description The MAX9918 evaluation kit (EV kit) provides a proven design to evaluate the MAX9918 wide input range, precision unidirectional/bidirectional,
More informationFM RADIO KIT ESSENTIAL INFORMATION. Version 2.0 GET IN TUNE WITH THIS
ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS GET IN TUNE WITH THIS FM RADIO KIT Version 2.0 Build Instructions Before you start, take
More informationEasy Transmitter. Support ETX_REV5_Manual V2.7 Revised
Easy Transmitter Introduction The Easy Transmitter kit from qrpkits.com provides a basic, crystal controlled transmitter with VXO tuning to provide a small tuning range around the crystal frequency. It
More informationELEC207 LINEAR INTEGRATED CIRCUITS
Concept of VIRTUAL SHORT For feedback amplifiers constructed with op-amps, the two op-amp terminals will always be approximately equal (V + = V - ) This condition in op-amp feedback amplifiers is known
More informationAN3008 Application note
Application note STOD2540, single inductor DC-DC converter generates multiple supply voltages for E-paper display Introduction This application note describes how to use the STOD2540 DC-DC converter to
More informationS Powered by +5V Supply. S Input Configurable for Electrical and Optical Evaluation
19-4980; Rev 0; 9/09 MAX3806 Evaluation Kit General Description The MAX3806 evaluation kit (EV kit) is an assembled and tested demonstration board that simplifies evaluation of the MAX3806 receiver for
More informationAnalog Effect Pedals. EE333 Project 1. Francisco Alegria and Josh Rolles
Analog Effect Pedals EE333 Project 1 Francisco Alegria and Josh Rolles Introduction For the first project, we ve chosen to design two analog guitar effect pedals. This report will discuss the schematic
More informationEvaluates: MAX17532 (TDFN) in 5V Output Voltage Applications. MAX V Output Evaluation Kit (TDFN) General Description. Features.
General Description The MAX753 5V evaluation kit (EV kit) (TDFN) is a fully assembled and tested circuit board that demonstrates the performance of the MAX753 4V, 00mA ultra-small, high-efficiency, synchronous
More information