Skylark Trace IV User Manual

Transcription

1 Skylark Trace IV User Manual A skylark soars above the clouds. 一只云雀在云上翱翔

2 SATETY WARNING SKYLARK OSD is for entertainment purpose only, users should bear all the risks involved when using this electronics device. Service center website: Because the product function unceasing renewal, you hand user manual and the actual content may try some. The latest user manual please from Skylark PPV service center web site. This user manual is updated on March 20, 2012.

3 Trace IV OSD User Manual 1.Main feature 1. Build in 5V/12V power supply.(new) 2. Build in barometer. 3. Compatible with auto antennan tracker. 4. Online firmware upgrade Hz GPS with backup battery 6. Selectable OSD Screen. 7. XT60 connector 8. Fly summarize 9. 80A Hight precision current sensor 2.Main connection Voltage/Current sensor GPS camera Trace IV OSD 5V 3.Packing list 1. Trace IV OSD board 2. 80A Current sensor 3. 10Hz GPS board 4. GPS cable 5. Current sensor cable 6. User manual 7. Reserve wire several pcs 12V AV transmitter

4 4.Trace IV OSD Connect with GPS VOL/CUR Sensor battery ESC power module Reset NC GND RSSI NC AUDIOOUT CVBSOUT CAMIN 12V GND 5V main board 5.Setting Trace IV OSD Setting GPS

5 6.OSD Screen [ standard screen ] [ simple screen ]

6 Displayed information description: Description Description Display Display Range Range Latitude N is North Latitude, S is South Latitude, Unit is Degree 90.0N~0~90.0S Longitude E is East Longitude, W is West Longitude, Unit is Degree 180.0E~0~180.0W Numbers of GPS satellites Numbers of GPS satellite that can be received signal currently. 0~9; 9 would be displayed even more than 9 Speed Total speed, unit is Km/ hour 0~999km/h Current Operation current, unit is A 0.0~99.9A Voltage System voltage, unit is V. it would flash when under voltage. 0.0~99.9V Electricity consumption The electricity consumed from system start-up till now, unit is mah 0.0~9999mAH Remaining electricity The battery symbol indicates the remaining electricity level, when it is nearly used up, the symbol would flash. It takes a 2200mAH battery as indication standard. Point of departure Indicate the point of departure Location & direction The plane icon indicates the existing location & direction corresponding to the point of departure. Up: North, Down: South, Left: West, Right: East. The flying direction is shown by the plane icon. Altitude corresponding to the point of departure Altitude that corresponding to the point of departure. The figure can be negative, unit is meter. Returning angle & direction Indicate the required angle and direction for a returning journey, the unit for angle is degree. When angle is less than 5 degree, it would consider as accurate, so direction would not be displayed. Horizontal distance corresponding to the point of departure The horizontal distance corresponding to the point of departure, the unit would be adjusted automatically. Signal indication of remote control When the device is under interference and out of control range, it would flash. Flying time The flying time is accumulated from the first take-off. When there are 4 or more GPS satellites and the speed exceeds 5m/s the first time, it starts counting ~9999m 0~99.9km

7 7.Skylark Trace IV OSD Setting 1. Click OSD->ScreenSet Skylark Trace IV OSD RSSI Calibration 1. Make sure the RC receiver RSSI is connected to the OSD board. 2. Use the Skylark USB Cable connect your computer and the GPS port of the Trace OSD board 3. Remote Control power on 4. RC receiver power on 5. Run Configuration Software 6. Click OSD->Calibrate 7. Click "Start" button

8 8. Remote Control power off 9. Click "Stop" button

9 10. Remote Control power on

10 8.Skylark Trace IV OSD Upgrade Download Skylark Configuration Software Trace OSD Firmware Upgrade 1. Download rhe Skylark Configuration Software and the Trace OSD Firmware V Unzip the SkylarkSetup V2.0.zip 3. Double click the SkylarkSetup V2.0.exe and install the software to your computer 4. Use the Skylark USB Cable connect your computer and the GPS port of the Trace OSD board 5. Unzip Trace firmware V1.6.zip 6. Double click SkylarkFPV icon on your computer desktop Trace