Model 3102D 0-2 kv H.V. Power Supply
|
|
- Katherine Taylor
- 6 years ago
- Views:
Transcription
1 Features Compact single width NIM package Regulated up to ±2000 V dc. 1 ma output Noise and ripple 3 mv peak to peak Overload and short circuit protected Overload, inhibit and polarity status indicators Inhibit and overload latching circuits Digital front panel meter Model 3102D 0-2 kv H.V. Power Supply Description The CANBERRA Model 3102D High Voltage Power Supply is a single-width NIM module designed primarily for use with photomultiplier and electron multiplier tubes. But it can be used with any detector requiring a bias voltage up to 2000 V and a current level of 1 ma or less. The 3102D allows the user to select from two continuously adjustable outputs, one ranging from ±15 to ±2000 V dc and the other from ±1.5 to ±200 V dc. The output voltage is measured and displayed by a three-digit voltmeter. In addition, this unit allows the user to select the output voltage polarity with an internal control. The 3102D can withstand any overload or short circuit for an indefinite period of time. It can be set using an internal jumper to allow for a manual reset or an automatic reset when the fault condition is removed. The 3102D features an output rise time of five seconds to protect preamplifiers and detectors from excessive surge currents while charging. Specifications INPUTS INPUT POWER The Model 3102D is powered from a standard NIM Bin and power supply, such as the Model 2100, 2000 or INHIBIT Logic low or ground inhibits the HV outputs; max logic low 0.7 V; logic high 1.3 V or open circuit enables. OUTPUTS HV OUTPUT ±15 to ±2000 V dc, continuously adjustable; 1 ma output current capability; rear panel SHV connector. 10 OUTPUT ±1.5 to ±200 V dc, continuously adjustable; Z out = 20 MΩ; rear panel SHV connector. CONTROLS ON/OFF Front panel toggle switch enables or disables output. RESET Pushbutton restores normal operation following a latched Inhibit and/or overload fault condition. VOLTAGE Front panel 10-turn control permits continuous adjustment of the output voltage. POLARITY Internal programming plug sets output polarity. INDICATORS HV OUTPUT 3-digit panel meter; 0 to 2.00 kv. POLARITY Front panel LEDs indicate polarity continuously. INHIBIT LED indicates Inhibit status. OVERLOAD LED indicates overload status. Phone contact information Benelux/Denmark (32) Canada Central Europe +43 (0) France (33) Germany (49) Japan Russia (7-495) United Kingdom (44) United States (1) For other international representative offices, visit our web site: or contact the CANBERRA U.S.A. office. NSP0003 2/07 Printed in U.S.A.
2 Model 3102D 0-2 kv H.V. Power Supply PERFORMANCE RIPPLE AND NOISE 3 mv peak to peak at 1 µa. OUTPUT STABILITY Long term drift of output voltage is 0.01%/hr. and 0.02%/8 hr. at constant input line voltage, load, and ambient temperature after a 30 minute warmup. TEMPERATURE COEFFICIENT ±50 ppm/ C after 30 minute warmup, operating range 0 to 50 C. REGULATION 0.001% variation in output voltage over the load range and 0.001% for ±0.1% input voltage change within the operating range at constant ambient temperature. OVERLOAD PROTECTION Power supply will withstand any overload, including a short circuit for an indefinite period. CURRENT LIMIT 1.3 ma maximum. DIAL ACCURACY ±1% of full scale. METER ACCURACY ±0.6% of full scale plus 10 volts. CONNECTORS HV OUTPUT Rear panel SHV. 10 OUTPUT Rear panel SHV. INHIBIT Rear panel BNC. POWER REQUIREMENTS +24 V 70 ma +12 V 160 ma* 24 V 10 ma 12 V 150 ma *With Brightness Control J4 set to HI, +12 V will draw 265 ma, which exceeds the normal Bin allotment of 167 ma for a single-width module. PHYSICAL SIZE Standard single width NIM module 3.43 x cm, (1.35 x 8.71 in.) per DOE/ER-0457T. NET WEIGHT 1.4 kg (3.1 lb). SHIPPING WEIGHT 2.4 kg (5.3 lb). ENVIRONMENTAL OPERATING TEMPERATURE 0 to 50 C. OPERATING HUMIDITY 0-80% relative, non-condensing. Meets the environmental conditions specified by EN 61010, Installation Category I, Pollution Degree Canberra Industries, Inc. All rights reserved.
3 Low-Noise Current Preamplifier SR570 DC to 1 MHz current preamplifier SR570 Current Preamplifier 5 fa/ Hz input noise 1 MHz maximum bandwidth 1 pa/v maximum gain Adjustable bias voltage Two configurable signal filters Variable input offset current Line or battery operation RS-232 interface The SR570 is a low-noise current preamplifier capable of current gains as large as 1 pa/v. High gain and bandwidth, low noise, and many convenient features make the SR570 ideal for a variety of photonic, low-temperature and other measurements. Gain The SR570 has sensitivity settings from 1 pa/v to that can be selected in a sequence. A vernier gain adjustment is also provided that lets you select any sensitivity in between. Gain can be allocated to various stages of the amplifier to optimize the instrument s performance. The low-noise mode places gain in the front end of the amplifier for the best noise performance. The high-bandwidth mode allocates gain to the later stages of the amplifier to improve the frequency response of the front end. In the low-drift mode, the input amplifier is replaced with a very low input-current op amp, reducing the instrument s DC drift by a factor of Filters SR $2295 (U.S. list) The SR570 contains two first-order RC filters whose cutoff frequency and type can be configured from the front panel. Together, the filters can be configured as a 6 or 12 db/oct rolloff low-pass or high-pass filter, or as a 6 db/oct rolloff band-pass filter. Cutoff frequencies are adjustable from 0.03 Hz to 1 MHz in a sequence. A filter reset button
4 SR570 Current Preamplifier is included to shorten the overload recovery time of the instrument when long filter time constants are used. Input Offset and DC Bias An input offset-current adjustment is provided to suppress any unwanted DC background currents. Offset currents can be specified from ±1 pa to ±1 ma in roughly 0.1 % increments. The SR570 also has an adjustable input DC bias voltage (±5 V) that allows you to directly sink current into a virtual null (analog ground) or a selected DC bias. Toggle and Blanking Two rear-panel opto-isolated TTL inputs provide additional control of the SR570. A blanking input lets you quickly turn off/on the instrument's gain which is useful in preventing front-end overloading. A toggle input inverts the sign of the gain in response to a TTL signal, allowing you to perform synchronous detection with a chopped signal. Battery Operation Three rechargeable lead-acid batteries provide up to 15 hours of battery-powered operation. An internal battery charger automatically charges the batteries when the unit is connected to the line. The charger senses the battery state and adjusts the charging rate accordingly. Two rear-panel LEDs indicate the charge state of the batteries. When the batteries become discharged, they are automatically disconnected from the amplifier circuit to avoid battery damage. Why Use a Current Amplifier? Many people wonder why current amplifiers are necessary. Why not simply terminate a current source with a resistor and amplify the resulting voltage with a voltage amplifier? The answer is twofold. To get a large voltage from a current, large resistors are necessary. In combination with cable capacitance, this can lead to unacceptable penalties in frequency response and phase accuracy. Current amplifiers have much better amplitude and phase accuracy in the presence of stray capacitance. Secondly, using resistive terminations forces the current source to operate into possibly large bias voltages a situation which is unacceptable for many sources and detectors. Current amplifiers can sink current directly into a virtual null or to a selected DC bias voltage. Ordering Information SR570 Low-noise current preamplifier $2295 O560RMD Double rack mount kit $85 O560RMS Single rack mount kit $85 O560SB Spare battery set (3 batteries) $150 No Digital Noise The microprocessor that runs the SR570 is "asleep" except during the brief interval it takes to change the instrument's setup. This ensures that no digital noise will contaminate lowlevel analog signals. RS-232 Interface The RS-232 interface allows listen-only communication with the SR570 at 9600 baud. All functions of the instrument (except power on) can be set via the RS-232 interface. The RS-232 interface electronics are opto-isolated from the amplifier circuitry to provide maximum noise immunity. SR570 rear panel
5 SR570 Current Preamplifier 10-9 Low Noise Mode 1 Low Noise Mode Current Noise (Amps/ Hz) Gain / Nominal Gain (db) k 10k 100k k 1M 100M 10-9 High Bandwidth Mode 1 High Bandwidth Mode Current Noise (Amps/ Hz) Gain / Nominal Gain (db) k 10k 100k k 1M 100M
6 SR570 Specifications Input Inputs Virtual null or user-set bias (±5 V) Input offset ±1 pa to ±1 ma adjustable DC offset current Maximum input ±5 ma Noise See graphs on previous page Sensitivity 1 pa/v to in sequence (Vernier adjustment in 0.5 % steps) Frequency response ±0.5 db to 1 MHz (Adjustable front-panel frequency response compensation for source capacitance) Grounding Amplifier ground is fully floating. Amplifier and chassis ground are available at rear panel. Input ground can float up to ±40 V. Filters Signal filters Gain allocation Low Noise High Bandwidth Low Drift 2 configurable (low-pass or highpass) 6 db/oct rolloff filters. 3 db points are settable in a sequence from 0.03 Hz to 1 MHz. Gain is allocated to the front end for best noise performance. Front-end gain is reduced for optimum frequency response. Low bias current amplifier is used for reduced drift at high sensitivity. Filter reset Output Long time constant filters may be reset with front-panel button. Gain accuracy ±(0.5 % of output C DC drift See table below Maximum output ±5 V into a high impedance load General External blanking External toggle Rear panel biasing Computer interface Power Dimensions Weight Warranty TTL input sets gain to zero TTL input inverts gain polarity ± ma, referenced to amplifier ground RS-232, 9600 baud, receive only 100/120/220/240 VAC, 6 W charged, 30 W while charging. Internal batteries provide 15 hours of operation between charges. Batteries are charged while connected to the line. 8.3" 3.5" 13.0" (WHD) 15 lbs. (batteries installed) One year parts and labor on defects in materials and workmanship Sensitivity Bandwidth* Noise (/ Hz)** Temp. coefficient DC Input (A/V) ±(% input + offset)/ C Impedance High BW Low Noise High BW Low Noise Low Drift (11 to 28 C) All Modes MHz 1.0 MHz 150 pa 150 pa 0.01 % + 20 na 1 Ω MHz 500 khz 100 pa 60 pa 0.01 % + 2 na 1 Ω khz 200 khz 60 pa 2 pa 0.01 % pa 100 Ω khz 20 khz 2 pa 600 fa 0.01 % + 20 pa 100 Ω khz 2 khz 600 fa 100 fa 0.01 % + 2 pa 10 kω khz 200 Hz 100 fa 60 fa 0.01 % fa 10 kω Hz 15 Hz 60 fa 10 fa % + 40 fa 1 MΩ Hz 10 Hz 10 fa 5 fa % + 20 fa 1 MΩ Hz 10 Hz 5 fa 5 fa % + 20 fa 1 MΩ Hz 10 Hz 5 fa 5 fa % + 20 fa 1 MΩ * Frequency compensation adjusted for flat frequency response ** Average noise in the frequency range below the 3 db point but above the frequency where 1/f noise is significant
Model 7000 Low Noise Differential Preamplifier
Model 7000 Low Noise Differential Preamplifier Operating Manual Service and Warranty Krohn-Hite Instruments are designed and manufactured in accordance with sound engineering practices and should give
More informationHITEK POWER XR KW X-RAY POWER SUPPLY MODULE
HITEK POWER XR1000 1 KW X-RAY POWER SUPPLY MODULE Component power supply for industrial x-ray systems, elemental analysis equipment, x-ray diffraction spectrometers, and materials process monitoring applications
More informationModel 6517B Electrometer / High Resistance Meter Specifications
VOLTS Accuracy (1 Year) 1 / C 2V 10µV 0.025+4 0.003+2 20V 100µV 0.025+3 0.002+1 200V 1mV 0.06+3 0.002+1 NMRR: 2V and 20V range > 60dB, 200V range > 55dB. 50Hz or 60Hz 2 CMRR: >120dB at DC, 50Hz or 60Hz.
More informationVariable-Gain High Speed Current Amplifier
Features Transimpedance (gain) switchable from 1 x 10 2 to 1 x 10 8 V/A Bandwidth from DC up to 200 MHz Upper cut-off frequency switchable to 1 MHz, 10 MHz or full bandwidth Switchable AC/DC coupling Adjustable
More information2302 Battery Simulator 2306, 2306-PJ Battery/Charger Simulators
Ultrafast response to transient load currents Choice of single- or dualchannel supplies Optimized for development and testing of battery-powered devices Variable output resistance for simulating battery
More information2017 Advanced Energy Industries, Inc. HITEK POWER MV2000 SERIES MEDIUM-VOLTAGE HIGH-CURRENT POWER SUPPLIES
2017 Advanced Energy Industries, Inc. HITEK POWER MV2000 SERIES MEDIUM-VOLTAGE HIGH-CURRENT POWER SUPPLIES Medium-voltage rack-mount power supplies Page 2 The MV2000 series high-performance, medium output
More informationLow Noise Variable Gain Low Frequency Voltage Amplifier
Features Variable Gain 40 to 100 db, Switchable in 20 db Steps Bipolar Input Stage, Recommended for Low Impedance Sources Smaller than 100 Ω Very Low Input Voltage Noise: 700 pv/ Hz DC-Coupled, Single
More informationVariable Gain Low Frequency Voltage Amplifier
Features Applications 20 to 80 db, Switchable in 20 db Steps Bipolar Input Stage, Recommended for Low Impedance Sources Smaller than 1 kω Single Ended and True Differential Input Models Bandwidth DC -
More informationOperation and Service Manual. 350 MHz Preamplifier SIM914. Stanford Research Systems
Operation and Service Manual Stanford Research Systems Revision 1.8 August 24, 2006 Certification Stanford Research Systems certifies that this product met its published specifications at the time of shipment.
More informationHITEK POWER XR KW X-RAY POWER SUPPLY MODULE
HITEK POWER XR1000 1 KW X-RAY POWER SUPPLY MODULE The HiTek Power XR1000 series is a component power supply for industrial x-ray systems, elemental analysis equipment, x-ray diffraction spectrometers,
More informationVariable Gain Sub Femto Ampere Current Amplifier
Features 0.4 fa Peak-Peak Noise Very High Dynamic Range: Sub-fA to 1 ma (> 240 db) Transimpedance (Gain) Switchable from 1 x 10 4 to 1 x 10 13 V/A Bandwidth up to 400 Hz, Rise Time Down to 0.8 ms - Independent
More informationUltra Low-Noise Variable Gain Low-Frequency Voltage Amplifier
Features Variable gain 40 to 100 db, switchable in 20 db steps Bipolar input stage, recommended for low impedance sources smaller than 50 Ω Ultra low input voltage noise: 400 pv/ Hz AC coupled, single
More informationModel 4402B. Ultra-Pure Sinewave Oscillator 1Hz to 110kHz Typical Distortion of % Serial No. Operating Manual
Model 4402B Ultra-Pure Sinewave Oscillator 1Hz to 110kHz Typical Distortion of 0.0005% Serial No. Operating Manual 15 Jonathan Drive, Unit 4, Brockton, MA 02301 U.S.A. Tel: (508) 580-1660; Fax: (508) 583-8989
More informationManual Supplement. This supplement contains information necessary to ensure the accuracy of the above manual.
Manual Title: 5502E Getting Started Supplement Issue: 3 Part Number: 4155211 Issue Date: 9/18 Print Date: November 2012 Page Count: 12 Revision/Date: This supplement contains information necessary to ensure
More informationUltra Low Noise Variable Gain Low Frequency Voltage Amplifier
Features Variable Gain 40 to 100 db, Switchable in 20 db Steps Bipolar Input Stage, Recommanded for Low Impedance Sources Smaller than 50 Ω Ultra low Input Voltage Noise: 400 pv/ Hz AC Coupled, Single
More informationLow Noise Variable Gain Low Frequency Voltage Amplifier
Measurement Features Variable Gain 40 to 100 db, Switchable in 20 db Steps Bipolar Input Stage, Recommended for Low Impedance Sources Smaller than 100 Ω Very Low Input Voltage Noise: 700 pv/ Hz DC-Coupled,
More informationDECLARATION OF CONFORMITY
DECLARATION OF CONFORMITY Manufacturer's Name: Transmille Ltd. Manufacturer's Address: Unit 4, Select Business Centre Lodge Road Staplehurst TN12 0QW. United Kingdom. Declares, that the product Product
More informationHITEK POWER OLS10K SERIES
10 KW HIGH VOLTAGE POWER SUPPLIES The HiTek Power OLS10K series range of single-output high voltage power supplies meets the exacting requirements found in electron-beam, ion-beam, and x-ray systems, as
More informationModels 900CT & 900BT. Tunable Active Single Channel Certified Filter Instrument
Tunable Active Single Channel Certified Filter Instrument Description Frequency Devices instruments are single channel; 8-pole low-pass or high-pass, front panel tunable filter instruments. The controls
More informationVariable-Gain High Speed Current Amplifier
Features Transimpedance (Gain) Switchable from 1 x 10 2 to 1 x 10 8 V/A Bandwidth from DC up to 200 MHz Upper Cut-Off Frequency Switchable to 1 MHz, 10 MHz or Full Bandwidth Switchable AC/DC Coupling Adjustable
More informationModel SR554 Transformer Preamplifier
Model SR554 Transformer Preamplifier Model SR554 Transformer Preamplifier 1290-D Reamwood Avenue Sunnyvale, California 94089 Phone: (408) 744-9040 Fax: (408) 744-9049 email: info@thinksrs.com www.thinksrs.com
More informationModel Quality in Test and Measurement Since 1949 OUTSTANDING PERFORMANCE DESCRIPTION APPLICATIONS ADDITIONAL FEATURES
Quality in Test and Measurement Since 1949 DC Source/Calibrators, Tunable Electronic Filters, Wideband Power Amplifiers Precision Phasemeters, Distortion Analyzers Function Generators, RC Oscillators Model
More informationLow Noise Variable Gain Low Frequency Voltage Amplifier
Features Variable Gain 40 to 100 db, Switchable in 20 db Steps Bipolar Input Stage, Recommended for Low Impedance Sources Smaller than 100 Ω Very Low Input Voltage Noise: 700 pv/ Hz DC-Coupled, Single
More informationManual Supplement. This supplement contains information necessary to ensure the accuracy of the above manual.
Manual Title: 550A Getting Started Supplement Issue: Part Number: 415509 Issue Date: 9/18 Print Date: November 01 Page Count: 19 Revision/Date: This supplement contains information necessary to ensure
More informationModel LIA100. Lock-in Amplifier
Model LIA100 Lock-in Amplifier Operations Manual Thorlabs, Inc 435 Route 206 Newton, NJ 07860 P-(973) 579-7227 F-(973) 300-3600 www.thorlabs.com Doc. Page 1 of 10 Table of Contents Chapter Description
More informationHigh Performance Current Transducer IT 200-S ULTRASTAB = A. ε L
High Performance Current Transducer IT 200-S ULTRASTAB For the electronic measurement of currents: DC, AC, pulsed..., with galvanic isolation between the primary circuit and the secondary circuit. I PM
More informationModel Operating Manual
Model 7500 DC to 1MHz Wideband Power Amplifier Operating Manual Copyright 2004. All rights reserved. Contents of this publication may not be reproduced in any form without the written permission of Krohn-Hite
More informationFluke 5820A Oscilloscope Calibrator Specifications
Fluke 5820A Oscilloscope Calibrator Specifications Voltage Function Volt Function DC Signal Square Wave Signal 1 Load into 50Ω into 1 MΩ into 50Ω into 1 MΩ Amplitude Range 0V to ±6.6V 0V to ±130V ±1 mv
More informationLock-In-Amplifier Module
Features BNC Connectors for Input and Output Signals Rugged Aluminium Housing Single Phase Detection with X Output Working Frequency 5 Hz... 10 khz, Digital Phase Shifter 0... 360 Parameter Control by
More informationPLUG N PLAY WATT DIGITAL FM TRANSMITTER. April, 2002 IM No
PLUG N PLAY 1000 1000 WATT DIGITAL FM TRANSMITTER April, 2002 IM No. 597 9972 OPERATION/FEATURE PROGRAMMING. The PNP 1000 allows the user to select many types of different operating parameters and features.
More informationAgilent N3300 Series DC Electronic Loads
Agilent N3300 Series DC Electronic Loads Data Sheet Increase your manufacturing test throughput with fast electronic loads Increase test system throughput Lower cost of ownership Decrease system development
More informationModel 863 Quad Timing Filter Amplifier Operating and Service Manual
Model 863 Quad Timing Filter Amplifier Operating and Service Manual Printed in U.S.A. ORTEC Part No. 733960 0411 Manual Revision C Advanced Measurement Technology, Inc. a/k/a/ ORTEC, a subsidiary of AMETEK,
More informationModel 9302 Amplifier-Discriminator Operating and Service Manual
Model 9302 Amplifier-Discriminator Operating and Service Manual Printed in U.S.A. ORTEC Part No. 733690 1202 Manual Revision C Advanced Measurement Technology, Inc. a/k/a/ ORTEC, a subsidiary of AMETEK,
More informationModel 34A. 3Hz to 2MHz 2-Channel Butterworth/Bessel HP, LP, BP, BR Plug-In Filter Card for Model 3905/3916 Chassis.
Model 34A 3Hz to 2MHz 2-Channel Butterworth/Bessel HP, LP, BP, BR Plug-In Filter Card for Model 3905/3916 Chassis Operating Manual Service and Warranty Krohn-Hite Instruments are designed and manufactured
More information5520A. Multi-Product Calibrator. Extended Specifications 2005
5520A Multi-Product Calibrator Extended Specifications 2005 5520A Specifications The following tables list the 5520A specifications. All specifications are valid after allowing a warm-up period of 30 minutes,
More informationGF 467F FUNCTION GENERATOR. PROTECTED RS232 + (USB OR LAN)* LabVIEW 0,01 Hz to 5 MHz CMos. Specifications. Other specifications
FUNCTION GENERATOR EAN CODE : 3760244880468 5 MHZ+RS232++(USB or LAN)* GF 467F COMPLETE : Reciprocal frequency counter 50 MHz. - Internal linear or logarithmic sweep, and external VCF or FM modulation.
More informationSIGNAL RECOVERY. Model 7265 DSP Lock-in Amplifier
Model 7265 DSP Lock-in Amplifier FEATURES 0.001 Hz to 250 khz operation Voltage and current mode inputs Direct digital demodulation without down-conversion 10 µs to 100 ks output time constants Quartz
More informationModel Hz to 10MHz Precision Phasemeter. Operating Manual
Model 6610 1Hz to 10MHz Precision Phasemeter Operating Manual Service and Warranty Krohn-Hite Instruments are designed and manufactured in accordance with sound engineering practices and should give long
More informationSeries OLS10KD 10kW HIGH VOLTAGE POWER SUPPLY
DESCRIPTION The Series OLS10KD range of high voltage power supplies recognises the requirement for high stability and very low ripple over a wide range of output voltages. This is achieved by combining
More informationMODEL 9050 EXTENDED SPECIFICATIONS. 50ppm TRANSPORTABLE CALIBRATOR
MODEL 9050 EXTENDED SPECIFICATIONS Ü 50ppm TRANSPORTABLE CALIBRATOR 9050A EXTENDED SPECIFICATIONS General Specifications TRANSMILLE LTD Warm Up Time Double the time since last used up to 20 minutes maximum
More informationModel MV106J/MV116J. ±10nVdc to ±11Vdc Precision DC Voltage Standard Source. Operating Manual
Model MV106J/MV116J ±10nVdc to ±11Vdc Precision DC Voltage Standard Source Operating Manual This page intentionally left blank. MV 106 & MV116 OPERATORS MANUAL Serial No. Win-man\mvman.wpd This page intentionally
More informationPM 6669 High-Precision Frequency Counter Specifications
PM 6669 High-Precision Frequency Counter Specifications Product Home Features Specifications Models, Options & Accessories Measuring functions Definitions Input specifications Auxiliary functions TimeBase
More informationHITEK POWER OLS10KD SERIES
10KW HIGH VOLTAGE POWER SUPPLY The HiTek Power OLS10KD series range of high voltage power supplies recognises the requirement for high stability and very low ripple over a wide range of output voltages.
More informationAUM FAMILY Programmable DC Power Supplies
AUM FAMILY Programmable DC Power Supplies 500W O/P Power 1U Half-Rack Front Panel Encoder & Tactile Switch Inputs 4-Digit Displays for V & I RS-485 & CAN Interface Standard Models IEEE488.2 or LAN, USB
More informationMODEL SR445A. 350 MHz PREAMPLIFIER
MODEL SR445A 350 MHz PREAMPLIFIER MODEL SR445A 350 MHz PREAMPLIFIER 1290-D Reamwood Avenue Sunnyvale, California 94089 Phone: (408) 744-9040 Fax: (408) 744-9049 email: info@thinksrs.com www.thinksrs.com
More informationOPERATING INSTRUCTIONS AND SYSTEM DESCRIPTION FOR THE. ISO-STIM 01D STIMULUS ISOLATION UNIT ±100 V / ±10 ma, bipolar output
OPERATING INSTRUCTIONS AND SYSTEM DESCRIPTION FOR THE ISO-STIM 01D STIMULUS ISOLATION UNIT ±100 V / ±10 ma, bipolar output VERSION 4.0 npi 2014 npi electronic GmbH, Bauhofring 16, D-71732 Tamm, Germany
More informationMODEL 9041 EXTENDED SPECIFICATIONS. 25ppm TRANSPORTABLE CALIBRATOR
MODEL 9041 EXTENDED SPECIFICATIONS 25ppm TRANSPORTABLE CALIBRATOR 9041 EXTENDED SPECIFICATIONS General Specifications TRANSMILLE LTD Warm Up Time Double the time since last used up to 20 minutes maximum
More informationSignal Conditioning Amplifier
FEATURES Plug-in amplifier design; amplifiers are removable from the front panel without rear access Constant-voltage or constant-current excitation; 0.5 to 15 V or 0.5 to 30 ma; selectable by single internal
More information5500A. Multi-Product Calibrator. Extended Specifications 2005
5500A Multi-Product Calibrator Extended Specifications 2005 5500A Specifications The following paragraphs detail specifications for the 5500A Calibrator. The specifications are valid after allowing a warm-up
More informationIntroduction to Analog Interfacing. ECE/CS 5780/6780: Embedded System Design. Various Op Amps. Ideal Op Amps
Introduction to Analog Interfacing ECE/CS 5780/6780: Embedded System Design Scott R. Little Lecture 19: Operational Amplifiers Most embedded systems include components that measure and/or control real-world
More informationBattery Simulator Battery/Charger Simulators
Test Equipment Depot - 800.517.8431-99 Washington Street Melrose, MA 02176 - TestEquipmentDepot.com 2302, 2302-PJ, Ultrafast response to transient load currents Choice of single- or dualchannel supplies
More informationLock-In Amplifiers SR510 and SR530 Analog lock-in amplifiers
Lock-In Ampliiers SR510 and SR530 Analog lock-in ampliiers SR510/SR530 Lock-In Ampliiers 0.5 Hz to 100 khz requency range Current and voltage inputs Up to 80 db dynamic reserve Tracking band-pass and line
More informationSignal Conditioning Amplifier
2300 System Micro-Measurements FEATURES Accepts all strain gage inputs (foil and piezoresistive), potentiometers, DCDT s, etc Selectable bridge excitation, 0.7 to 15 VDC (11 steps), plus 0.2 to 7 VDC continuously
More informationMODEL: 20VS2-02. Hybrid IC Isolation Amplifiers 20 Series
MODEL: 0VS-0 Hybrid IC Isolation Amplifiers 0 Series ISOLATION AMPLIFIER (-port isolation) Functions & Features Being used for printed wiring board installation High-linearity Low power consumption Isolating
More informationLOW NOISE AMPLIFIER SA SERIES
LOW NOISE AMPLIFIER SA SERIES Accurate and ultra low noise measurements of very small signals Achieve one of the highest level of low noise amplification SA600 series SA400 series Differential input SA200
More informationDSA150 Series. xxx Series. 150 Watts. AC-DC Power Supplies. Models & Ratings. Mechanical Details 3.92 (99.8) 2.18 (55.5) 4.92 (125.
15 Watts xxx Series Ultra Slim Design 15% Peak Load for 3 seconds Ambient Operation from -1 C to +7 C High Efficiency Selectable Overload Characteristic Selectable Remote Inhibit or Enable 3 Year Warranty
More informationPhoton Counters SR430 5 ns multichannel scaler/averager
Photon Counters SR430 5 ns multichannel scaler/averager SR430 Multichannel Scaler/Averager 5 ns to 10 ms bin width Count rates up to 100 MHz 1k to 32k bins per record Built-in discriminator No interchannel
More informationVariable Gain 100 MHz Wideband Voltage Amplifier
Features 10 to 60 db, Switchable in 10 db Steps Bandwidth DC... 100 MHz, Switchable to 10 MHz Built-In Temperature Compensation for Low Drift of 0.6 µv/k 2.5 nv/ Hz Input Noise Switchable AC/DC-Coupling
More information8558A 8 1/2 Digit Multimeter
8558A 8 1/2 Digit Multimeter Product Specifications March 2019 Rev. A 2019 Fluke Corporation. All rights reserved. Specifications are subject to change without notice. All product names are trademarks
More informationTOSHIBA International Corp
TOSHIBA International Corp GUIDE SPECIFICATIONS THREE PHASE UNINTERRUPTIBLE POWER SYSTEM TOSHIBA 4200FA 30 kva CT Internal Battery UPS GUIDE SPECIFICATIONS 1 (30 kva CT) 1.0 SCOPE 1.1 System This specification
More informationSeries OLH10KD 10kW HIGH VOLTAGE POWER SUPPLIES
Series OLH10KD FEATURES 10kW of output power Wide dynamic range with dual supply configuration Output voltages from 60kV to 500kV for high range Output voltages from 6kV to 10kV for low range Robust IGBT
More informationDSA-LX. Digital Signal Analyzer. Radiation Safety. Amplified.
Radiation Safety. Amplified. DSA-LX Digital Signal Analyzer Nuclear Healthcare Homeland Security & Defense Labs and Education Industrial and Manufacturing KEY FEATURES Integrated desktop MCA based on Digital
More informationThe MDU150 Series provides the same benefits as the MPU150 Series, with nominal 48 volt DC input.
The innovative MPU products incorporate Power Factor Correction (PFC) with a low-profile package designed to meet 1U height constraints. The MPU150-4530G and MPU150-4350G provide high current +3.3 V and
More informationISOBE5600. Data sheet. Isolated Probe Systems. - ISOBE5600 Isolation system - ISOBE5600 Transient recorder. Features and Benefits
ISOBE5600 Isolated Probe Systems - ISOBE5600 Isolation system - ISOBE5600 Transient recorder Data sheet Features and Benefits ISOBE5600 Isolation system - Cost-effective - Fiber-optic isolation - Analogue-in
More informationDIN SERIES DIGITAL PANEL METERS ELECTRO- NUMERICS, INC.
DIN SERIES DIGITAL PANEL METERS ELECTRO- NUMERICS, INC. MODEL SELECTION GUIDE The DIN Series of Digital Panel Meters are rugged low cost meters for the measurement of dc voltage, dc current, Process voltage
More informationAdvanced Test Equipment Rentals ATEC (2832)
Established 1981 Advanced Test Equipment Rentals www.atecorp.com 800-404-ATEC (2832) A.H. Systems Model Active Monopole Antennas Active Monopole Antenna Series Operation Manual 1 TABLE OF CONTENTS INTRODUCTION
More informationModule Input type Ranges TEDS Filters (LP = lowpass, HP = highpass) Piezoresistive bridge ±0.5 to mv/ma 1 ma exc
HSI Series Modules Selection Guide HSI Series Modules Single channel High bandwidth - for dynamic signals Isolation (all models Analog signal output (±5 V Single channel modularity For DEWETRON systems
More informationOPERATING AND MAINTENANCE MANUAL
5Hz to 1MHz WIDE RANGE FULLY AUTOMATIC DISTORTION ANALYZER MODEL 6900B SERIAL NO. OPERATING AND MAINTENANCE MANUAL Unit 4, 15 Jonathan Drive, Brockton, MA 02301-5566 Tel: (508) 580-1660; Fax: (508) 583-8989
More informationTRANSMILLE 3010A PRECISION MULTIPRODUCT CALIBRATOR EXTENDED SPECIFICATIONS
TRANSMILLE 3010A PRECISION MULTIPRODUCT CALIBRATOR EXTENDED SPECIFICATIONS www. transmille.com 3010A EXTENDED SPECIFICATIONS General Specifications TRANSMILLE LTD Warm Up Time Double the time since last
More informationGreen LED (right of 'D' type connector)
3050A EXTENDED SPECIFICATIONS General Specifications TRANSMILLE LTD Warm Up Time Double the time since last used up to 20 minutes maximum Standard Interfaces USB Optional Interfaces GPIB (IEEE-488) : RS232
More informationDC Electronic Loads 8500 Series
Data Sheet DC Electronic Loads 2400W 600 W - 1200 W 300 W Versatile & Economical DC Electronic Loads The 8500 series Programmable DC Electronic Loads can be used for testing and evaluating a variety of
More informationKeysight Technologies N9320B RF Spectrum Analyzer
Keysight Technologies N9320B RF Spectrum Analyzer 9 khz to 3.0 GHz Data Sheet Definitions and Conditions The spectrum analyzer will meet its specifications when: It is within its calibration cycle It has
More informationAgilent 8902A Measuring Receiver
Agilent 8902A Measuring Receiver Technical Specifications Agilent 11722A Sensor Module Agilent 11792A Sensor Module Agilent 11793A Microwave Converter Agilent 11812A Verification Kit The Agilent Technologies
More informationLF442 Dual Low Power JFET Input Operational Amplifier
LF442 Dual Low Power JFET Input Operational Amplifier General Description The LF442 dual low power operational amplifiers provide many of the same AC characteristics as the industry standard LM1458 while
More information5520A. Multi-Product Calibrator. Extended Specifications
5520A Multi-Product Calibrator Extended Specifications Specifications The following tables list the 5520A specifications. All specifications are valid after allowing a warm-up period of 30 minutes, or
More informationVoltage-to-Frequency and Frequency-to-Voltage Converter ADVFC32
a FEATURES High Linearity 0.01% max at 10 khz FS 0.05% max at 100 khz FS 0.2% max at 500 khz FS Output TTL/CMOS Compatible V/F or F/V Conversion 6 Decade Dynamic Range Voltage or Current Input Reliable
More informationAgilent N9320B RF Spectrum Analyzer
Agilent N9320B RF Spectrum Analyzer 9 khz to 3.0 GHz Data Sheet Definitions and Conditions The spectrum analyzer will meet its specifications when: It is within its calibration cycle It has been turned
More informationIsolated, Frequency Input 5B45 / 5B46 FEATURES APPLICATIONS PRODUCT OVERVIEW FUNCTIONAL BLOCK DIAGRAM
Isolated, Frequency Input 5B45 / 5B46 FEATURES Isolated Frequency Input. Amplifies, Protects, Filters, and Isolates Analog Input. Generates an output of 0 to +5V proportional to input frequency. Model
More informationArtisan Technology Group is your source for quality new and certified-used/pre-owned equipment
Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment FAST SHIPPING AND DELIVERY TENS OF THOUSANDS OF IN-STOCK ITEMS EQUIPMENT DEMOS HUNDREDS OF MANUFACTURERS SUPPORTED
More informationSynthesized Function Generators DS MHz function and arbitrary waveform generator
Synthesized Function Generators DS345 30 MHz function and arbitrary waveform generator DS345 Function/Arb Generator 1 µhz to 30.2 MHz frequency range 1 µhz frequency resolution Sine, square, ramp, triangle
More informationDC Electronic Loads 8500 series
Data sheet DC Electronic Loads 8500 series 2400W 600 W - 1200 W 300 W Versatile & Economical DC Electronic Loads The 8500 series Programmable DC Electronic Loads can be used for testing and evaluating
More informationAnalog Lock-In Amplifier
Operation and Service Manual Stanford Research Systems Revision 1.03 July 12, 2018 Certification Stanford Research Systems certifies that this product met its published specifications at the time of shipment.
More informationAgilent dc Electronic Loads Models N3300A-N3307A
Agilent dc Electronic Loads Models N3300A-N3307A Technical Specifications Increase your Manufacturing Test Throughput with Fast Electronic Loads Increase test system throughput Lower cost of ownership
More informationArbitrary/Function Waveform Generators 4075B Series
Data Sheet Arbitrary/Function Waveform Generators Point-by-Point Signal Integrity The Arbitrary/Function Waveform Generators are versatile high-performance single- and dual-channel arbitrary waveform generators
More informationRTD), LM335 Voltage, or AD592 current. c. Constant TE Current (8350 only)
Photonics and Instrumentation 309 Model 8000 Modular Controller Comprehensive laser diode protection features Large graphics display, allowing full four-channel visibility Complete laser diode characterization
More informationData Sheet SC5317 & SC5318A. 6 GHz to 26.5 GHz RF Downconverter SignalCore, Inc. All Rights Reserved
Data Sheet SC5317 & SC5318A 6 GHz to 26.5 GHz RF Downconverter www.signalcore.com 2018 SignalCore, Inc. All Rights Reserved Definition of Terms 1 Table of Contents 1. Definition of Terms... 2 2. Description...
More informationLAUREL ELECTRONICS, INC.
LAUREL ELECTRONICS, INC. Laureate True RMS AC Voltage & Current Meter with 1 Cycle Update at 50/60 Hz Features True AC or AC plus DC RMS measurement with crest factor of 3.0 at FS Fast response: reading
More informationSignal Conditioning Amplifier
FEATURES Accepts full, half, or quarter bridges; all bridgecompletion gages built in, including 120/1000- and 350-ohm dummies Fully adjustable and regulated bridge excitation on each channel; up to 12
More informationLow Profile. 3 Year Warranty
MCC Series 400 W Regulated Output Optional 200 W Non-regulated Conditioned Rail 1 to 4 Configurable Outputs MIL-STD-1275 and DEF-STAN 61-5 MIL-STD-461 and DEF-STAN 59-411 Low Profile Rugged Construction
More informationOperator s Manual. DA1855A Differential Amplifier
Operator s Manual DA1855A Differential Amplifier DA1855A Differential Amplifier Operator s Manual November, 2014 2014 Teledyne LeCroy, Inc. All rights reserved. Unauthorized duplication of Teledyne LeCroy
More informationQUAD PROGRAMMABLE FILTER/AMPLIFIERS For the and Signal Conditioning Systems
27604 QUAD PROGRAMMABLE FILTER/AMPLIFIERS For the 27000 and 28000 Signal Conditioning Systems SYSTEM 28000 FEATURES Graphical User Interface (GUI) and Ethernet network interface for system control Intelligent
More informationFSK DEMODULATOR / TONE DECODER
FSK DEMODULATOR / TONE DECODER GENERAL DESCRIPTION The is a monolithic phase-locked loop (PLL) system especially designed for data communications. It is particularly well suited for FSK modem applications,
More informationIsolated, Linearized Thermocouple Input 5B47 FEATURES APPLICATIONS PRODUCT OVERVIEW
Isolated, Linearized Thermocouple Input 5B47 FEATURES Isolated Thermocouple Input. Amplifies, Protects, Filters, and Isolates Thermocouple Input Works with J, K, T, E, R, S, and B-type thermocouple. Generates
More informationModular Controller. Key Features. Model P hotonics. Comprehensive laser diode protection features. Advanced 16-bit control technology
16 P hotonics LASER DIODE TESTING FIBER OPTIC TEST Key Features Comprehensive laser diode protection features Advanced 16-bit control technology Complete laser diode characterization (L,V,I) using 8500
More informationVitrek 4700 Precision High Voltage Meter
Vitrek 4700 Precision High Voltage Meter 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com High Voltage Reference Divider Performance
More informationHomework Assignment 03
Homework Assignment 03 Question 1 (Short Takes), 2 points each unless otherwise noted. 1. Two 0.68 μf capacitors are connected in series across a 10 khz sine wave signal source. The total capacitive reactance
More informationModel 9305 Fast Preamplifier Operating and Service Manual
Model 9305 Fast Preamplifier Operating and Service Manual This manual applies to instruments marked Rev 03" on rear panel. Printed in U.S.A. ORTEC Part No.605540 1202 Manual Revision B Advanced Measurement
More informationAPPENDIX D DISCUSSION OF ELECTRONIC INSTRUMENTS
APPENDIX D DISCUSSION OF ELECTRONIC INSTRUMENTS DC POWER SUPPLIES We will discuss these instruments one at a time, starting with the DC power supply. The simplest DC power supplies are batteries which
More informationSingle Supply, Rail to Rail Low Power FET-Input Op Amp AD820
a FEATURES True Single Supply Operation Output Swings Rail-to-Rail Input Voltage Range Extends Below Ground Single Supply Capability from + V to + V Dual Supply Capability from. V to 8 V Excellent Load
More informationTrue RMS Bench Multimeter 5492B
Data Sheet True RMS Bench Multimeter 5492B True RMS Bench Multimeter The B&K Precision model 5492B is a versatile 5½-digit, 120,000-count bench multimeter suitable for applications in education, service
More information