WINDOW PATCH ANTENNA INSTALLATION INSTRUCTIONS Section I
|
|
- Brandon Eaton
- 6 years ago
- Views:
Transcription
1 Page 1 of 5 WINDOW PATCH ANTENNA INSTALLATION INSTRUCTIONS Part# Section I Frequency Band Power Rating Low power up to 35 watts (cw power) Cellular CDMA 02445G Cellular GSM 02518B VHF MHz 02518D VHF MHz 02630T UHF MHz 02630X UHF MHz 02630Z UHF MHz Do not install the Disguised Decal Antenna System with radios that transmit at more than 75 watts (cw power). The Disguised Decal Antenna System ( Antenna ) is tuned to the dielectric constant of glass and must be installed on glass to work properly. The Antenna may be installed temporarily for initial testing by taping (non-metallic tape only) it to the glass surface prior to removing the paper backing. It is important to note that the VSWR of the Antenna will be high unless the protective paper backing is removed from the Antenna. Permanent damage to the Antenna may occur if the Antenna is used without removing the protective paper backing which protects the adhesive prior to transmitting on your radio. Care should be exercised so that the Antenna is not damaged by folding or bending. STEP 1 GLASS PREPARATION 1) Using standard glass cleaner, make sure glass surface is clean where you wish to install the Antenna. 2) Glass temperature must not be under 40 degrees Fahrenheit (5 degrees centigrade) at time of installation. Preferred mounting locations for the Antenna: A) For radios transmitting 35 watts (cw power) or less install the Antenna either on the front windshield 3-4 to the passenger side of the rear view mirror or on the top centre of the rear window. B) For radios transmitting between 35 and 75 watts (cw power) install the Antenna on the top centre of the rear window. STEP 2 CABLE INSTALLATION Your low power Antenna may be installed on the front windshield or rear window. If installing on the rear window with defroster wires see installation on rear windows with Defroster Wires in Section III. 1) After determining the location for the Antenna, route the cable from the desired location to the radio by leaving enough cable to make a stress free connection to the Antenna. 2) Route the cable along either side of the window trim (as shown in Figure 1 on page 2) and under the door or roof molding. Cable can be routed either from the left or right side of the Antenna. Any excess cable may be coiled to accommodate ease of installation after attaching the RF connector (not included). Note: Make sure not to damage cable when replacing molding.
2 Page 2 of 5 Figure 1 STEP 3 ANTENNA POSITIONING 1) When installing on the front windshield position the Antenna 3-4 to the passenger s side of the rear view mirror at top of the windshield. Make sure the Antenna is positioned so as to not impair vision while driving. 2) When installing on the rear window (recommended for radios transmitting from 35 to 75 watts cw power) with defroster wire see section III. 3) Area B of the Antenna (as shown in Figure 2 below) is not to be adhered to the window but installed above the top edge of the window allowing for a flexible connection to the cable. The Antenna and the 3-pin connector on the supplied cable may be mated either under the window trim or on the trim exterior depending on make of vehicle. 4) After positioning the Antenna per Figure 2, Remove Paper Backing one side at a time firmly pressing outward from the centre toward the edge thus adhering the Antenna to the desired location. Once installed, the Antenna may be damaged if removed. 5) Use cable clips to affix cable next to the Antenna. Make sure the window surface is clean by using standard window glass cleaner prior to permanently installing the Antenna. Your Antenna, when installed correctly on the front windshield in the glare band, is virtually invisible from outside of the vehicle. The Antenna is meant to permanently adhere to the glass and may be damaged if removed. It is possible for the weight of the cable to slowly peel the Antenna off of the window if the cable clips are not used and the cable is not properly mounted. Figure 2
3 Page 3 of 5 Section II LOW POWER TUNING PROCEDURE For Radios Transmitting Up To 35 Watts (cw power) Your Antenna is a new and improved version from Benelec. Due to the variable properties of automobile glass, your Antenna must be tuned to the specific glass of your vehicle. Do not install Antenna on metal. This includes fade to clear/racetrack and metal tinting for defrosting purposes. If possible check metal content with glass checker to avoid damage to the Antenna and possible damage to window. For more information see Section III. 1) Trim cable to dimensions per your connector instructions taking care not to nick the inner conductor or the braid. 2) Solder desired connector (not included) per your specific connector installation instructions. Avoid crimping centre conductor, especially in high power installations. 3) Make sure cable is routed and completely installed. 4) With the non-metal tuning tool (enclosed) and a VSWR meter, match the Antenna to the desired transceiver operating frequency: VHF Antennas (135, 146, 155, 165) Low Power up to 35 watts (cw power) A) Tune control # 1 (See Figure 3 on page 4) to minimize reflected power and VSWR. B) Tune control # 2 to further minimize reflected power and VSWR. C) Repeat steps A and B as necessary. Make sure tuning assembly screws are not touching metal after installed. Applying electrical tape over the tuning assembly adjustment screws will eliminate the possibility of shorting the tuning assembly to ground. UHF Antennas (220, 417, 429, 460, 485) Low Power up to 35 watts (cw power) A) Tune control #1 (See Figure 3 on page 4) to minimize reflected power and VSWR. B) Tune control #2 to further minimize reflected power and VSWR. C) Tune control #3 to further minimize reflected power and VSWR. D) Repeat steps A,B and C as necessary. Make sure tuning assembly screws are not touching metal after installed. Applying electrical tape over the tuning assembly adjustment screws will eliminate the possibility shorting the tuning assembly to ground.
4 Page 4 of 5 Section III INSTALLATION ON REAR WINDOWS WITH DEFROSTER WIRE Note: For radios transmitting under 35 watts, the Antenna may be installed on the front windshield or rear window. For radios transmitting over 35 watts (35 watts to 75 watts cw power) it is recommended that the Antenna be installed on the rear window. If possible check metal content with glass checker to avoid damage to the antenna and possible damage to window. Place Antenna on top centre position of rear window with area B of the Antenna (as shown in Figure 2 on page 2) above the top edge of the window so that the horizontal lines do not directly overlap the defroster wires (see Figure 4 below). Figure 4
5 Page 5 of 5 Section IV INSTALLATION WITH TINTING Many vehicles have some metal content in the window glass. In most cases the performance of your Antenna will not be affected. However certain types of Installations will be affected by the various metallic contents found in automobile window glass: 1) Fade to Clear / Racetrack On some newer vehicle windshields you may find a metal shield around the edge of the windshield. To install the Antenna on a windshield with fade to clear / racetrack only area B on the Antenna (as shown in Figure 5 below) should be in the proximity of the fade to clear / racetrack portion of the windshield. 2) Insta-Clear Some vehicle manufacturers offer an optional windshield with the ability to heat the windshield in winter to eliminate ice and/or fog, sometimes referred to as Insta-clear Avoid installing the Antenna on this type of windshield. If your car has an Insta-clear windshield mount your Antenna on the rear window. 3) After-Market Tinting Some after-marketing tinting contains lead in the tinting to reflect ultraviolet rays. This type of tinting will affect the Antenna s performance. To install the antenna with after-market tinting: A) Select the area desired to install the Antenna. B) Cut out an outline of the Antenna and remove the tinting. C) Install the Antenna per Section I. Figure 5
Technician License. Course
Technician License Course Technician License Course Chapter 4 Lesson Plan Module - 10 Practical Antennas The Dipole Most basic antenna The Dipole Most basic antenna The Dipole Total length is ½ wavelength
More informationUHF 477MHZ CB 27MHZ ANTENNA NAME ADVENTURER FLEXI-DIPOLE FLEXI-DIPOLE UHF STUMPY 4WHEELER EXPLORER REDBACK HI-GLASS XTENDER RUGGED HI-STEEL
Benelec-1 27MHZ UHF 477MHZ CB 31CM 33CM 50CM 65CM 67CM 92CM 87CM 93CM 85CM 150CM 130CM 120CM PART NUMBER(S) ANTENNA NAME 02152 REDBACK 02623 HI-GLASS 02623I (STEEL) 02623IBK (BLACK) HI-STEEL 026264 FAZE
More informationCommercial Vehicle Productivity and Security. Antenna Configuration. External Antenna Installation (model 6650H only) Contigo 6650H/6651H Beacon
Commercial Vehicle Productivity and Security The 6650H/6651H is a versatile and economical GPS tracking beacon designed for fleet management needs in all commercial vehicles. The H designation in the model
More informationPCB Antenna with Cable Integration Application Note Version 4
PCB Antenna with Cable Integration Application Note Version 4 CONTENTS 1. BASICS 2. APPLICATIONS 3. SIZE 4. SHAPE 5. GROUND PLANE SIZE 6. IMPEDANCE 7. BANDWIDTH 8. VSWR 9. GAIN 10. EFFICIENCY 11. POLARIZATION
More informationAssembly Instructions for the 1.5 Watt Amplifier Kit
Assembly Instructions for the 1.5 Watt Amplifier Kit 1.) All of the small parts are attached to a sheet of paper indicating both their value and id. 2.) Leave the parts affixed to the paper until you are
More informationSPORTCRAFT ANTENNAS. INSTALLATION INSTRUCTIONS for FLUSH WINGTIP COM ANTENNAS
01A SPORTCRAFT ANTENNAS INSTALLATION INSTRUCTIONS for FLUSH WINGTIP COM ANTENNAS 1.0 INTRODUCTION. 1.1 GENERAL. These antennas have been designed by Bob Archer of Torrance, California utilizing concepts
More information2007 Honda CR-V EX. KTC trim tool set SOJATP2014 * Trim pad remover, Snap-on A177A or equivalent, commercially available
Special Tools Required KTC trim tool set SOJATP2014 * Trim pad remover, Snap-on A177A or equivalent, commercially available * Available through the American Honda Tool and Equipment Program; call 888-424-6857
More informationMobile Gain Antennas MHz Models RRA-4935/RRA-4936
890-960 MHz Models RRA-4935/RRA-4936 Installation See Table 1 for recommended antenna location for various vehicles. The installation procedure which follows is for a typical passenger car. The procedure
More informationMilton Keynes Amateur Radio Society (MKARS)
Milton Keynes Amateur Radio Society (MKARS) Intermediate Licence Course Feeders Antennas Matching (Worksheets 31, 32 & 33) MKARS Intermediate Licence Course - Worksheet 31 32 33 Antennas Feeders Matching
More informationTechnician License Course Chapter 4. Lesson Plan Module 10 Practical Antennas
Technician License Course Chapter 4 Lesson Plan Module 10 Practical Antennas The Dipole Most basic antenna Total length is ½ wavelength (½ λ) Usual construction: Two equal halves of wire, rod, or tubing
More informationAt Larsen we want our customers to be confident they can find the right antenna for the right
MOBILE ANTENNAS At Larsen we want our customers to be confident they can find the right antenna for the right application. For this reason, we have provided some guidelines for mobile antenna selection.
More informationOptimizing Your Stations Performance
Optimizing Your Stations Performance A few hints / techniques, recommendations for getting the most RF out to the Antenna from your HF, VHF / UHF station. Tonights Presenters: Doug Theriault NO1D John
More informationhuprf Panoramic Adaptor Installation FT847
huprf Panoramic Adaptor Installation FT847 These instructions cover installation of the PAT board in the 1st IF of the FT847 45.705MHz this gives access to all receiver options on the main receiver. A
More informationAntennas and Propagation Chapters T4, G7, G8 Antenna Fundamentals, More Antenna Types, Feed lines and Measurements, Propagation
Antennas and Propagation Chapters T4, G7, G8 Antenna Fundamentals, More Antenna Types, Feed lines and Measurements, Propagation =============================================================== Antenna Fundamentals
More informationGuide. Installation. Wilson Electronics, Inc. Direct Connection High Power iden Amplifi er 800 MHz Band. Contents:
Amplifier Installation Guide Direct Connection High Power iden Amplifi er 800 MHz Band Contents: Guarantee and Warranty 1 Before Getting Started / How it Works 3 Installing a Wilson Outside Antenna - In-Vehicle
More informationA 75-Watt Transmitter for 3 Bands Simplified Shielding and Filtering for TVI BY DONALD H. MIX, W1TS ARRL Handbook 1953 and QST, October 1951
A 75-Watt Transmitter for 3 Bands Simplified Shielding and Filtering for TVI BY DONALD H. MIX, W1TS ARRL Handbook 1953 and QST, October 1951 The transmitter shown in the photographs is a 3-stage 75-watt
More informationhuprf Panoramic Adaptor Installation IC718
Panoramic Adaptor Installation IC718 These instruction cover installation of the PAT board in the 1st IF of the ICOM IC718 64.455MHz this gives access to all receiver options on the main receiver. Although
More informationInstallation Guide - Addendum Garmin to Contigo 6150 & 6151
Beacon and Garmin: Dispatch and Navigation The Contigo 6150 & 6151 provide a fleet management interface to Garmin Personal Navigation Devices (PNDs) including the nüvi 2x5, 465, 12xx, 13xx, and 14xx series.
More informationTRK-SR2 Install Guide 8/29/01 10:22 AM Page 1. TRK-SR2 Roof-Mount Satellite Radio Antenna Installation Guide
TRK-SR2 Install Guide 8/29/01 10:22 AM Page 1 TRK-SR2 Roof-Mount Satellite Radio Antenna Installation Guide TRK-SR2 Install Guide 8/29/01 10:22 AM Page 2 TABLE OF CONTENTS About Installation..........................................
More informationDX 33HML. Full Channel AM/FM Mobile Transceiver OWNER S MANUAL. Printed In Malaysia AT H PD000802
DX 33HML Full Channel AM/FM Mobile Transceiver Printed In Malaysia AT3601014H PD000802 OWNER S MANUAL TABLE OF CONTENTS Page Specification.................................... 2 Installation Location.....................................
More informationTS-930: Installing the Inrad Roofing Filter Mod
TS-930: Installing the Inrad Roofing Filter Mod The TS-930 roofing filter mod consists of a 6 pole, 4 to 5 khz wide filter followed by a high dynamic range, feedback amplifier. The amplifier provides enough
More informationFilm Antenna for VICS FM Multiplex Broadcasting
Antenna for VICS FM Multiplex Broadcasting Kazushige Ogino Haruhiko Kondo Naoki Kushima Kazuo Takayama K. Ogino et al.: Antenna for VICS FM Multiplex Broadcasting 1. Introduction In recent years, the use
More information4 Antennas as an essential part of any radio station
4 Antennas as an essential part of any radio station 4.1 Choosing an antenna Communicators quickly learn two antenna truths: Any antenna is better than no antenna. Time, effort and money invested in the
More information600G2 Internal Sliding Adapter Panel Shelf Instructions
Instruction Sheet 860391986 Issue 6, February 2013 SYSTIMAX Solutions 600G2 Internal Sliding Adapter Panel Shelf Instructions General The SYSTIMAX 600G2 adapter panel shelf is 19-inch wide x 1.75-inch
More informationSPECIFICATION PATENT PENDING. Embedded Flexible 4G LTE Wide Band Antenna MHz, MHz. Covers worldwide 2G/3G/4G Bands
SPECIFICATION PATENT PENDING Part No: Product Name: FXUB65.07.0180C Minima Embedded Flexible 4G LTE Wide Band Antenna 700-960MHz, 1700-2700MHz Features: Flexible Wideband Antenna Covers worldwide 2G/3G/4G
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 33380 SIDE S 2007 S2000 Issue Date AUG 2006 PARTS LIST Left upper side strake 2 Grommets 2 Butyl O-rings 2 Washer-screws, 6 x 20 mm
More informationDX 33HP. 10 Meter Amateur Mobile Transceiver OWNER S MANUAL. Download this Manual Free of Charge at
DX 33HP SIG 1 3 TX PWR 5 7 9+30dB POWER HI NB/ANL MED LO HI LO BAND ECHO RX/TX VOL SQ MIC RF FM PA AM D/A E/B F/C ECHO TIME BAND 10 Meter Amateur Mobile Transceiver Download this Manual Free of Charge
More informationALWAYS ATTACH THE SAFETY ROPE TO A STABLE SUPPORT BEFORE ATTEMPTING TO ATTACH THE UNIVERSAL MOUNT TO A WINDOW FRAME OR RAIL.
MFJ-1623 Introduction The MFJ-1623 was designed to provide portable or permanent HF communications on 30 through 10 meters and VHF on 6 meters. The universal mount design allows the user to install the
More informationWARNING: DO NOT PROCEED WITHOUT READING THIS PAGE.
WARNING: DO NOT PROCEED WITHOUT READING THIS PAGE. The B-1030-G produces at least 300 watts of VHF R.F. power and is not to be taken lightly. Severe R.W. burns can be sustained at this power level! Power
More informationIntroduction LOADING COIL COUNTERPOISE ATTACHMENT ANTENNA ATTACHMENT. Figure 1: MFJ-1625 Window/Balcony Mount Antenna
Introduction MFJ-1625 The MFJ-1625 is a 200 Watt antenna tuner that was designed to provide portable or permanent HF communications on 80 through 10 meters and VHF on 6 meters. The universal mount design
More informationINSTALLATION AND CONNECTIONS
INSTALLATION AND CONNECTIONS 3 Unpacking After unpacking, immediately report any damage to the delivering carrier or dealer. Keep the shipping cartons. For a description and a diagram of accessory equipment
More informationLC31L-BAT Link Coupler
Instruction Manual For the LC31L-BAT Link Coupler 09 March 2018 2012-2018 by Ralph Hartwell Spectrotek Services All rights reserved 2 RADIO FREQUENCY WARNING NOTICE If the LC31L-BAT is installed incorrectly
More informationTechnician Licensing Class. Lesson 4. presented by the Arlington Radio Public Service Club Arlington County, Virginia
Technician Licensing Class Lesson 4 presented by the Arlington Radio Public Service Club Arlington County, Virginia 1 Quiz Sub elements T6 & T7 2 Good Engineering Practice Sub element T8 3 A Basic Station
More informationModel CC-25HV Antenna Retrofit Kit
Model CC-5HV Retrofit Kit Coast to Coast RV Services 0 George Young Street, Auburn NSW Postal Address: PO Box 5, Regents Park NSW Phone: 0 965 7600 Fax: 0 965 7688 Email Technical: technical@coastrv.com.au
More informationWARNING: DO NOT PROCEED WITHOUT READING THIS PAGE.
WARNING: DO NOT PROCEED WITHOUT READING THIS PAGE. The B-2530-G produces at least 300 watts of VHF R.F. power and is not to be taken lightly. Severe R.W. burns can be sustained at this power level! Power
More informationYagi and Omni Antennas Installation Manual
Yagi and Omni Antennas Installation Manual 25500445 Rev. A0 0218 Printed in U.S.A. Copyright 2018 Federal Signal Corporation Limited Warranty This product is subject to and covered by a limited warranty,
More informationTOYOTA PRIUS BODY SIDE MOLDING Preparation
Preparation Part Number: PT938-47160-XX Kit Contents Item # Quantity Reqd. Description 1 1 Molding, LH Front Door 2 1 Molding, LH Rear Door 3 1 Molding, RH Front Door 4 1 Molding, RH Rear Door Hardware
More informationBuilding the Sawdust Regenerative Receiver
Building the Sawdust Regenerative Receiver Introduction The Sawdust is a super regenerative receiver using the basic Armstrong design architecture. The receiver uses one toroidal transformer to provide
More informationModel CC-25HV Antenna Retrofit Kit
Model CC-5HV Antenna Retrofit Kit Coast to Coast RV Services 0 George Young Street, Auburn NSW 1 Postal Address: PO Box 15, Regents Park NSW 1 Phone: 0 965 7600 Fax: 0 965 7688 Email Technical: technical@coastrv.com.au
More informationBMW X5 OEM RUNNING BOARD PART#SBBW
INSTALLATION INSTRUCTIONS 2014-2016 BMW X5 OEM RUNNING BOARD PART#SBBW-146-74 QTY HARDWARE 1 Driver Side OEM Running Board 1 Passenger Side OEM Running Board 8 Rivet Pin 1 Page Step 1: Verify all parts
More informationDX 29HP. 10 Meter Amateur Mobile Transceiver OWNER S MANUAL PRINTED IN MALAYSIA PN:A412308CNA
DX 29HP 10 Meter Amateur Mobile Transceiver OWNER S MANUAL PRINTED IN MALAYSIA PN:A412308CNA TABLE OF CONTENTS Page Specification.................................... 2 Installation Location.....................................
More informationTS-870: Installing the Inrad Roofing Filter Mod
TS-870: Installing the Inrad Roofing Filter Mod The TS-870 roofing filter mod consists of a 6 pole, 4 to 5 khz wide filter followed by a high dynamic range feedback amplifier. The amplifier provides enough
More informationGPS Dome Installation Manual
GPS Dome 1.01 Installation Manual Contents Introduction... 3 Overview... 3 Cautions... 4 Installation... 4 Installation Kit... 4 GPS Rece iver System with GPS Dome... 5 SMA Cables Connectors... 5 Installation
More informationIC-781: Installing the Inrad Roofing Filter Mod
IC-781: Installing the Inrad Roofing Filter Mod The Icom IC-781 roofing filter mod consists of a 6-pole, 4 to 5 khz wide filter followed by a high dynamic range, feedback amplifier. The amplifier provides
More informationMFJ Manual Loop Tuner Considerations
Pagina 1 0 items Proceed to Secure Checkout All Categories Accessories Analyzers Products Tuners Morse Code / CW Power Supplies Product Search Search! List All Products Site Menu Customer Account Order
More informationCON NEX HP. OWNER'S MANUAL Full Channel AM/FM Amateur Mobile Transceiver TABLE OF CONTENTS TUNING THE ANTENNA FOR OPTIMUM S.W.R..
TABLE OF CONTENTS PAGE SPECIFICATIONS... 2 INSTALLATION... 3 LOCATION... 3 CON NEX - 4300HP MOUNTING THE RADIO... 3 IGNITION NOISE INTERFERENCE... 4 ANTENNA... 4 TUNING THE ANTENNA FOR OPTIMUM S.W.R..
More informationThank you for purchasing the Ameritron SDA-100 Antenna
Thank you for purchasing the Ameritron SDA-100 Antenna When properly installed this antenna will provide continuous coverage of 3.5 to 30 MHz with a 6' whip, also 6.0 to 60 MHz without a whip. Installation
More informationLesson 11: Antennas. Copyright Winters Version 1.0. Preparation for Amateur Radio Technician Class Exam
Lesson 11: Antennas Preparation for Amateur Radio Technician Class Exam Topics Antenna ½ wave Dipole antenna ¼ wave Vertical antenna Antenna polarization Antenna location Beam antennas Test Equipment Exam
More informationObservations Regarding Selection and Installation of Masthead VHF whip antennas:
VHF AIS masthead antenna and coax installation, selection, and test. Stan Honey and Dan Jowett 28 August 2018 Observations Regarding Selection and Installation of Masthead VHF whip antennas: Whip Antennas
More informationA short, off-center fed dipole for 40 m and 20 m by Daniel Marks, KW4TI
A short, off-center fed dipole for 40 m and 20 m by Daniel Marks, KW4TI Version 2017-Nov-7 Abstract: This antenna is a 20 to 25 foot long (6.0 m to 7.6 m) off-center fed dipole antenna for the 20 m and
More informationNAVIGATION SYSTEM INSTALLATION INSTRUCTIONS
NAVIGATION SYSTEM INSTALLATION INSTRUCTIONS These instructions along with the pictures were performed in a 2008 Yukon. Please use them only as a reference since they might not exactly match your vehicle
More informationCellular Signal Booster Multi-User Tri-Band
weboost Drive AM100-Pro Cellular Signal Booster Multi-User Tri-Band ! THE Drive AM100-Pro SIGNAL BOOSTER MAY REMAIN ON, IN VEHICLES WHOSE 12V DC POWER SOURCES DO NOT AUTOMATICALLY SHUTDOWN WHEN THE VEHICLE
More informationTechnician Licensing Class. Antennas
Technician Licensing Class Antennas Antennas A simple dipole mounted so the conductor is parallel to the Earth's surface is a horizontally polarized antenna. T9A3 Polarization is referenced to the Earth
More informationPontiac Grand Am SC/T Installation Instruction Sheet Aftermarket Front Fascia
Aftermarket Front Fascia be used correctly to install the secondary fascia to the existing fascia. 1 Fascia Front 5 Bolt M6-1.0x60 5 Washer 1/4x9/16 2 Bolt/Washer Assembly 1 Nut/Washer Assembly 1. Six
More informationAUDIO SYSTEMS 8F - 1 AUDIO SYSTEMS CONTENTS
TJ AUDIO SYSTEMS 8F - 1 AUDIO SYSTEMS CONTENTS page GENERAL INFORMATION INTRODUCTION... 1 DESCRIPTION AND OPERATION ANTENNA... 1 IGNITION-OFF DRAW FUSE... 1 RADIO... 1 RADIO NOISE SUPPRESSION... 2 SPEAKER...
More informationDX 66V OWNER S MANUAL. Full Channel AM/FM Mobile Transceiver Built in Frequency Counter with Roger Beep
WARRANTY This radio is covered by a two year limited parts and labor warranty. Limited means that we will repair problems caused by factory defects or normal use at no charge. Before returning a radio
More informationConflicts. TOYOTA Highlander 2015 Fender Flares Part Number: Accessory Code: BF7000. Safety Tools Safety Glasses
Highlander 2015 Fender Flares Part Number: 00016-48016 Accessory Code: BF7000 Conflicts Note: Factory Splash Guards Kit Contents Item # Quantity Reqd. Description 1 1 Left Front Fender Flare 2 1 Right
More informationSignal Mirror Installation Instructions Toyota Tacoma
Signal Mirror Installation Instructions 2005-2015 Toyota Tacoma THE safety accessory of the 21 st Century. P/N 210-0115-0 Rev. A4 (3/11/15), BTV 2005 Muth Mirror Systems, LLC Page 3 of 12PplPage 3 of 12
More informationAUDIO SYSTEMS 8F - 1 AUDIO SYSTEMS CONTENTS
J AUDIO SYSTEMS 8F - 1 AUDIO SYSTEMS CONTENTS page DIAGNOSIS... 2 GENERAL INFORMATION... 1 page SERVICE PROCEDURES... 6 GENERAL INFORMATION Following are general descriptions of major components used in
More informationG4HUP Panoramic Adaptor Installation FT1000MP
G4HUP Panoramic Adaptor Installation FT1000MP These instruction cover installation of the PAT board in the 1st IF of the FT1000MP 70.455MHz this gives access to all receiver options on the main receiver.
More informationRF Current Meter Kit
Kit When assembled, this kit provides you with a simple but effective means of measuring the current in antenna wires, and of looking for braid currents on coax feeders. The more current you can get flowing
More information* * APPLICABLE MODELS: 2014 > MAZDA 3
PART NUMBER: 0000 8C L46 GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0604-000* APPLICABLE MODELS: 204 > MAZDA 3 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage Chart MIRROR ASSEMBLY: Mirror
More informationLow Loss Pre-Connectorized Cable Sets, LL58 Series, DC-3.5GHz
Low Loss Pre-Connectorized Cable Sets, LL58 Series, DC-3.5 reliable performance, dependable service Replace traditional RG types for benefit of: lower loss better shielding > - 90dB Drop in replacement
More informationLOW PROFILE ANTENNA MHz NEMO A10AA1441A. Electrical NEMO SI. Mechanical Data
1575 MHz LOW PROFILE ANTENNA Low Profile GPS Antenna Used for various applications, including marine, outdoor, indoor, general purposes. NEMO A10AA1441A Electrical NEMO SI Termination TNC BULKHEAD FEMALE
More information87.5 TO MHz BAND II 2 WAY 4.8dBi STACKED DIPOLE ANTENNA
87.5 TO 108.0 MHz BAND II 2 WAY 4.8dBi STACKED DIPOLE ANTENNA 1. INTRODUCTION 3 1.1. GENERAL INFORMATION 3 1.2. UNPACKING AND CHECKING 3 1.3. WARRANTY 3 1.4. USER SAFETY RESPONSIBILITY 4 1.5. INSTALLATION
More informationBushwacker Jeep Flat Style Fender Flares Front Pair
Bushwacker Jeep Flat Style Fender Flares Front Pair Note: These instructions involve cutting parts of your vehicle. Please read all instructions prior to starting. Installation Time: 3-4 Hours Tools Required:
More informationBuilding the Sawdust Regenerative Receiver
Building the Sawdust Regenerative Receiver Introduction The Sawdust is a super regenerative receiver using the basic Armstrong design architecture. The receiver uses one toroidal transformer to provide
More informationInstructions MODIFICATION KIT MODEL SBM - 1O2-1 INTRODUCTION PARTS LIST FOR THE
Instructions FOR THE MODIFICATION KIT MODEL SBM - 1O2-1 INTRODUCTION This modification Kit applies to the following Heath Transceivers: 1. All Models HW-100, SB-100, SB-101 and SB-101W. 2. Any Model SB-102
More informationTechnician License. Course
Technician License Course Technician License Course Chapter 4 Lesson Plan Module - 9 Antenna Fundamentals Feed Lines & SWR The Antenna System The Antenna System Antenna: Transforms current into radio waves
More informationMFJ-834 RF Ammeter. Introduction. Uses
MFJ-834 RF Ammeter Introduction Congratulations on purchasing the MFJ-834 RF Ammeter. The MFJ-834 is designed for measuring in-line RF feedline current on 1.8-30 MHz while having low interaction on the
More informationMustang Eleanor Style Louvers - Pre-painted (05-10) - Installation Instructions
Mustang Eleanor Style Louvers - Pre-painted (05-10) - Installation Instructions The below installation instructions work for the following products: Mustang Eleanor Style Louvers - Pre-painted (05-10)
More informationPart Number: ;-02;-03;-08;-10;-11;-18;-21
Document # 4065 4/3/06 TOYOTA MATRIX 2006 - FENDER FLARES Section I Installation Preparation Part Number: 00016-12120-01;-02;-03;-08;-10;-11;-18;-21 Code: SF1 Kit Contents Item # Quantity Reqd. Description
More informationAutomotive Electrical & Injection Moulding Specialists. Listen Research Innovate Design. striptinning.com
Automotive Electrical & Injection Moulding Specialists striptinning.com We are committed to driving down costs of automotive heated glazing parts, multi-function brackets and all cabled connectors achieved
More informationFlat Style Fender Flares Front Pair. Jeep. Included in Hardware Kit:
Jeep Flat Style Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationNoise Suppression Guide
Page 1 of 6 Noise Suppression Guide Diagnosing and treating noise problems in your car audio system This guide will help you diagnose and treat problems with extraneous noise in your car audio system.
More informationDC Injector (Bias Tee) kit. Technical Manual
DC Injector (Bias Tee) kit Technical Manual Document Author Dave Powis, G4HUP Date 7 Jan 2017 Version Issue 2_0 Document Ref HUP-05-020 http://huprf.com Tel +44 (0)1473 737717 g4hup@outlook.com Contents
More informationSPECIFICATION PATENT PENDING MHz, MHz. Covers worldwide 4G/3G/2G Bands. Isotropic Radiation Pattern
SPECIFICATION PATENT PENDING Part No: Product Name: FXUB68.07.0180C Minima Embedded Flexible 4G LTE Wide Band Antenna 700-960MHz, 1700-2700MHz Features: Flexible Wideband Antenna Covers worldwide 4G/3G/2G
More informationTW4040. The Adventurer Monobander INSTRUCTION MANUAL. TransWorld Antennas
TW4040 The Adventurer Monobander TransWorld Antennas INSTRUCTION MANUAL Contents 1 Limited Warranty 3 2 Important Safety Information 4 3 Specifications 3.1 Mechanical 4 3.2 Electrical 4 3.3 VSWR Performance
More informationBi-Color Signal Mirror Installation Instructions
Bi-Color Signal Mirror Installation Instructions 2005-2009 Toyota Tacoma THE safety accessory of the 21 st Century. P/N 210-0141-0 Rev. A2 (3/30/09), BTV 2007 Muth Mirror Systems, LLC Page 3 of 13PplPage
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions Ford Explorer 1996-2001, Ford Explorer SportTrac 2001, Ford Ranger 1996-2001, Mazda B-2500\B-3000\B-4000 1998-2001, Mercury Mountaineer 1997-2001 THE safety accessory
More informationDual Band Filter Assembly Manual
Dual Band Filter Assembly Manual 12 January 2018 Rev D Version Theory of Operation: The purpose of a Bandpass Filter is to filter out or reject all unwanted signals. The original KN-Q7A Receive Filter
More informationUser Guide for the Alpha Loop Jr+ Antenna
User Guide for the Alpha Loop Jr+ Antenna Manufactured by: Alpha Antenna 1.888.482.3249 Website: http://alphaantenna.com User Guide Version 3.1 Page 1 Table of Contents Introduction... 3 Product Overview...
More informationAmeritron RCS-10 INTRODUCTION
Ameritron RCS-10 INTRODUCTION The RCS-10 is a versatile antenna switch designed for 50-ohm systems. It handles high power, and sealed relays offer excellent life and connection reliability. It requires
More informationINSTALLATION INSTRUCTIONS
SG57f GENUINE PARTS INSTALLATION INSTRUCTIONS. DESCRIPTION: Sunroof Wind Deflector. APPLICATION: Pathfinder; Frontier with no roof rails 3. PART NUMBER: 999D4-XR00 4. KIT CONTENTS: Item No. ) ) 3) 4) 5)
More informationRugged Ridge Body Armor Guard Kit, 5 Pieces, Black (07-Current JK 4-door)
Rugged Ridge Body Armor Guard Kit, 5 Pieces, Black (07-Current JK 4-door) Installation Time: 60 Minutes Tools Required: Notes: Phillips head screwdriver 3/8 socket or Flat head screwdriver 1/2 socket 7
More informationA WILSON ELECTRONICS BRAND DRIVE 4G-X FLEET PROFESSIONAL VEHICLE CELLULAR SIGNAL BOOSTER KIT. User Manual. NEED HELP? support.weboost.com
A WILSON ELECTRONICS BRAND DRIVE 4G-X FLEET PROFESSIONAL VEHICLE CELLULAR SIGNAL BOOSTER KIT User Manual NEED HELP? support.weboost.com 866.294.1660 Index Package Contents 1 STEP 1: Mount Outside Antenna
More informationAlpha Delta Communications, Inc. Model DX-OCF Off-Center-Fed 7 Band Antenna
Alpha Delta Communications, Inc. Model DX-OCF Off-Center-Fed 7 Band Antenna 75/80, 40, 20, 17, 12, 10, and 6 meters (50.0-51.0 MHz) NO TUNER REQUIRED! Installation Instructions One leg is 45 ft., the other
More informationFM Wireless Microphone Kit Instructions for Assembly Page 1 of 5
Instructions for Assembly Page 1 of 5 1. Find Resistor R1. Remove any tape that may be attached to the leads. Bend the leads as needed to insert Resistor R1 into the printed circuit board in the holes
More informationStep by Step Building PJ meter ARDF Receiver Kit. CRKITS.COM August 5, 2013
Step by Step Building PJ-80 80-meter ARDF Receiver Kit CRKITS.COM August 5, 2013 What is ARDF? ARDF is the abbreviation of Amateur Radio Direction Finding, or so called Fox Hunting. If you are looking
More informationImproved Ionospheric Propagation With Polarization Diversity, Using A Dual Feedpoint Cubical Quad Loop
Improved Ionospheric Propagation With Polarization Diversity, Using A Dual Feedpoint Cubical Quad Loop by George Pritchard - AB2KC ab2kc@optonline.net Introduction This Quad antenna project covers a practical
More informationTote Bag, CD Case, and Glasses Case
Tote Bag, CD Case, and Glasses Case Designed by Christina Inge Materials: Classic Cottons Black and White: Black Swirls (3623-9965-8): 1 yard White Swirls (3623-9966-8): ¼ yard Black Dots (3623-3998-8):
More informationPage 1 of 12 2016 Cadillac ATS 2.0L Eng Premium 1Search Print Date: ANTENNA Digital Radio Antenna Cable Replacement Fig 1: Digital Radio Antenna Cable Preliminary Lower the rear of the headliner as needed.
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions 2004 2008 Ford F-150 XLT, FX4, & Lariat Pre-wired without side signals Pre-wired with side signals Without side directional lights, see page 2 With side directional
More informationAmphenol RF UHF. UHF Connector Series UHF. Description. Features/Benefits. Applications
Amphenol RF 136 Connector Series Description Invented in the 1930 s by an Amphenol Engineer named E. Clark Quackenbush, coaxial connectors are general purpose units developed for use in low frequency systems
More informationAustraliaN Cellular Networks. Mobile Phones / Fixed Mobile Broadband / Telemetry Data NETWORK TYPE BAND CARRIER NOTES
Mobile Phones / Fixed Mobile Broadband / Telemetry Data GSM G Next G WiFi AustraliaN Cellular Networks NETWORK TYPE CARRIER 900 TELSTRA / OPTUS / VODAFONE STANDARD AUSTRALIAN 2G GSM FREQUENCY (2.5G) GSM
More informationGENUINE ACCESSORIES INSTALLATION INSTRUCTIONS. ITEM QTY DESCRIPTION Usage Chart
PART NUMBER: 0000 8C R0 GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0554-000* APPLICABLE MODELS: 203 > CX-5 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage Chart MIRROR ASSEMBLY: Mirror
More informationTechnician License Course Chapter 4. Lesson Plan Module 9 Antenna Fundamentals, Feed Lines & SWR
Technician License Course Chapter 4 Lesson Plan Module 9 Antenna Fundamentals, Feed Lines & SWR The Antenna System Antenna: Transforms current into radio waves (transmit) and vice versa (receive). Feed
More informationHot Water for the K2. K1RFD Building the K2 More K2 Photos. Using an HW-101 as a 100-watt PA. Hot Water for the K2. EchoStation
Page 1 of 5 K1RFD Building the K2 More K2 Photos EchoStation Using an HW-101 as a 100-watt PA When I was a young ham in 1977, I saved money to buy and build a Heathkit HW-101. The rig has served me well
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions Toyota RAV4 1996-2000 THE safety accessory of the 21 st Century. P/N 210-0034-0 Rev B1 (11-19-02), GG 2002 Muth Co. LLC. Note: Professional Installation Recommended
More informationPART NUMBER: T-R20 PACKAGE CONTENTS: GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Scuff Plate TOOLS REQUIRED: APPLICABLE MODELS: 2013 MAZDA CX-
PART NUMBER: 0000-8T-R20 PACKAGE CONTENTS: GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS TOOLS REQUIRED: APPLICABLE MODELS: 2013 MAZDA CX-5 FRONT SCUFF PLATE (Qty 2) 50% ISOPROPYL ALCOHOL/RESIDUE FREE
More information