Basic Concept, Operation and Control of HVDC Transmission System
|
|
- Branden Rose
- 6 years ago
- Views:
Transcription
1 Basic Concept, Operation and Control of HVDC Transmission System hrs. July 29, 2008 Room 2003, T.102, EGAT Head Office Nitus Voraphonpiput, Ph.D. Engineer Level 8 Technical Analysis Foreign Power purchase Agreement Branch Power Purchase Agreement Division Electricity Generating Authority of Thailand
2 Objective Introducing operation, and control of the High Voltage Direct Current Transmission System. Note: This presentation continues from the morning session. Basic mathematics and electrical engineering knowledge will be useful for attendee. 2
3 Contents 1. HVAC vs. HVDC 2. HVDC Principle Q&A for 15 minutes Coffee break 10 minutes 3. Control of DC Transmission Q&A for 15 minutes 3
4 1. HVAC vs. HVDC Why use DC transmission? This question is often asked. One response is that losses are lower, but is it true? Reference [2] has been explained using Insulation ratio and Power capacity in order to proof this statement. 4
5 1. HVAC vs. HVDC Insulation ratio of HVAC and HVDC (Ref. 1-2) A given insulation length for an overhead line, the ratio of continuous working withstand voltage factor (k) is expressed as, (note 1 k 2 ) k = DC withstand voltage AC withstand voltage(rms) = 1.0 A line has to be insulated for over-voltages expected during faults, switching operations, etc. Normally AC transmission line is insulated against over-voltages of more than 4 times the normal effective (rms) voltage. 5
6 1. HVAC vs. HVDC This insulation requirement can be met by insulation corresponding to an AC voltage of times the normal rated voltage. k AC Insulation level Rated AC Voltage (phase - ground) 1 = = (rms) 2.5 For suitable converter control the corresponding HVDC transmission ratio is expressed as k DC Insulation level Rated DC Voltage (pole - ground) 2 = = 1.7 6
7 1. HVAC vs. HVDC Insulation ratio for a DC pole-ground voltage (V d ) and AC phase-ground (V p ) is expressed as insulation ratio( K) = = insulation length required for each AC phase insulation length required for each DC Pole AC insulation level AC withstand voltage DC insulation level DC withstand voltage It can be seen that the actual ratio of insulation levels is a function of AC/DC voltage. Next, determine AC/DC voltage. (rms) = k k k 1 2 V V P d 7
8 1. HVAC vs. HVDC Determine AC/DC voltage Assumed resistances (R) of the lines are equal in both cases (HVDC and HVAC). AC Loss = 3 x R x I L 2 and DC Loss = 2 x R x I d 2 Let losses in both cases are equal, so that, 3 I d = I L 2 The power of a HVAC system and a bipolar HVDC system are as: AC Power = V P I cos φ DC Power = 2V d I d 3 L 8
9 1. HVAC vs. HVDC At the same power transfer, So that, AC Power DC Power = 2 1 V p = V d 3 cosφ 3VPI 2V L d cosφ = I d 3 2 V P cosφ = 1 V d Thus, insulation ratio (K) can be written as k K = k 1 k 3 cosφ cosφ 2 It can be seen that HVDC requires insulation ratio at least 20% less that the HVAC which essentially reflects the cost. 9
10 1. HVAC vs. HVDC Power Capacity Compared a double circuit HVAC line (6 lines) and double circuit DC line of Bipolar HVDC. Power transmitted by HVAC (P ac ) and HVDC (P dc ) are P = ac 6V PI L cosφ P = 6V On the basic of equal current and insulation, I d = I L, K=1: dc d I d P dc = 6 k k k V I k k P 1 1 ac P L = = 2 k2 cos 1.47 P φ cosφ ac 10
11 1. HVAC vs. HVDC For the same values of k, k 1 and k 2 as above and pf is assumed to 1.0, the power transmitted by overhead lines can be increased to 147%. The percentage line losses, which is inversion of the power transmit, are reduced to 68%. In addition, for underground or submarine cables, power transmitted by HVAC cable can be increase 294 % and line loss reduced to 34%. Note: for cable k equals at least two. 11
12 1. HVAC vs. HVDC From reference [3], losses are lower is not correct. The level of losses is designed into a transmission system and is regulated by the size of conductor selected. DC and AC conductors, either as overhead transmission lines or submarine cables can have lower losses but at higher expense since the larger cross-sectional area will generally result in lower losses but cost more. The reasons that HVDC have been used are: 1. An overhead d.c. transmission line with its towers can be designed to be less costly per unit of length. 2. It is not practical to consider AC cable systems exceeding 50 km (due to VAR charging of the cable). 3. Some a.c. electric power systems are not synchronized to neighboring networks even though their physical distances between them is quite small. 12
13 2. HVDC Principle The HVDC valve comprises the thyristors acting as controlled switch. In the OFF state, the thyristor blocks the current to flow, as long as the reverse or forward breakdown voltages is not exceeded. It changes to ON state if it is forward biased (V AK > 0) and has small positive Gate voltage applied between the Gate and the Cathode. Gate (G) Anode (A) Cathode (K) 13
14 2. HVDC Principle Thyristor switches between conducting state (ON) and nonconducting (OFF) state in response to control signal (firing) as its characteristic. The Gate voltage need not to be present when the thyristor is already in ON state. 14
15 2. HVDC Principle Anode (A) R d = V AK / I A i A R d V T Anode (A) Cathode (K) R r i r R r = V AK / I A V T P loss-on state = V T.I A(avg.) + R d.i A 2 (rms) Cathode (K) P loss-off state = R r.i r 2 (rms) 15
16 2. HVDC Principle ON-OFF state - ON state continues until current drops to zero, even reverse bias appears across the thyristor. - The critical time to clear charge carriers in the semi-conductor is referred as the turn-off time t off. If forward bias appears to soon, t < t off, thyristor can not OFF. V AK > 0 and V G >0 OFF V AK > 0 and t < t off ON I A < 0 t > t off OFF 16
17 2. HVDC Principle ON State OFF State 17
18 2. HVDC Principle Single Phase Bridge Rectifier I d Th1 Th3 I s Ld V s V d Rd = 10Ω Th4 Th2 U S = 220 V α = o 30 18
19 2. HVDC Principle V s I s α = 30 Voltage waveform of inductor (L d ), V Ld = Vd R d I d V d Voltage waveform of resistor (R d ), V Rd = R d I d Th 3 Th 1 Th 3 Th 4 Th 2 Th 4 I d 19
20 2. HVDC Principle I s 150 Hz Harmonics in the voltage and current waveform. 250 Hz 350 Hz DC 100 Hz V d 200 Hz 300 Hz DC I d 100 Hz 50 Hz 20
21 2. HVDC Principle Even DC side does not have reactive power (Q), the reactive power still presents on the AC side. The reactive power occurrence is caused by the delay angle (α) (or called firing angle) of the current waveform. P = V S I S cos α V s I s Q = V S I S sin α 30 V S α = ms time I S Phasor of fundamental component 21
22 2. HVDC Principle V d I s I d 50 Hz 100 Hz 100 Hz 150 Hz 200 Hz 250 Hz 350 Hz 300 Hz Product of V d and I d is (active) power (P). Product of phasor V S and phasor I S is not the apparent power (S). It represents the active power (P) and reactive power (Q). There are harmonic distortion power, which is a new term caused by the higher harmonics (more than 50 Hz). It is represented by D (distortion power). Finally, S 2 = P 2 + Q 2 becames S 2 = P 2 + Q 2 + D 2. 22
23 2. HVDC Principle V I s s Increasing I d Ith1 L k Ith2 Ith1 Ith2 µ is overlap angle µ I d V d commutation Increasing L k Ld Rd The inductance L k represents reactance on AC side (called commutating reactance). Due to nature of an inductor, The inductor current can not change suddenly. Thus, during turn-off of the Th1 (and Th2) and turn-on of the Th3 (and Th4), both are in conducting state for a short time (overlap time). This phenomena occurs during commutation of the thyristors. It can be seen that if current is high, overlap angel is increased. In addition, if inductance is high, overlap angle is also increased. 23
24 2. HVDC Principle I s Inductor current can not suddenly be changed, thus there is a slope. V s α = 30 µ cosα + cos( α + µ ) cosφ 2 V d Th 3 Th 1 Th 3 Th 4 Th 2 Th 4 I d 24
25 2. HVDC Principle The impact of the overlap angle (µ) is the reduction of the average dc voltage (V d ). It decreases the harmonic content of the ac current (I s ) and power factor of the AC side. V d V d V d V T Ideal case V do D R R d V d X = V do = 2 2 π π f X K L K K I d D X X K I d Voltage drop due to commutating reactance is represented as D X I d Overall voltage drop V T and D R are very less compared to D X. Thus, there are usually neglected. I d 25
26 2. HVDC Principle 3-pulse converter Natural commutation VA Th1 V dα I L L R d d VB Th2 I L t VC Th3 Ld V dα Rd V A = 2 VP sin ωt V B = 2 VP sin ωt-120 V C = 2 VP sin ωt+120 o α = 0 o α = 60 o α = 90 o α =120 V =.17V cosα = V cosα d 1 P d 0 26
27 2. HVDC Principle Positive average voltage Negative average voltage V V d d 0 o α = 60 o 45 Rectifier o 90 V V d d 0 Inverter = cosα o 135 o 180 Rectifier mode can be performed when firing angle is less than 90 degrees. Average voltage is zero when the firing angle is 90 degrees. α Inverter mode can be performed when firing angle is more than 90 degrees. 27
28 2. HVDC Principle V d α=60 α=30 I d 28
29 2. HVDC Principle V A, I A 120 V B, I B V C, I C Th 1 Th 2 Th 3 Th 1 Th 2 Th 3 I d 29
30 2. HVDC Principle V A, I A Reversing phase sequence α=30 α=120 V d Positive voltage Negative voltage I d Inverter mode can be performed as long as the DC current continues flow. 30
31 2. HVDC Principle V A Lk V dα D X V k V B Lk Id t V A µ µ α α V k IC IA IB IC IA IB V B V d D X = V = d 0 cosα 3 ωl 2π k I d D X 31 t
32 2. HVDC Principle The commutating reactance (X k ) results in decreasing of DC voltage, but it increases DC voltage in inverter mode. It can also be seen that the overlap time will γ increase when DC current is high and this can cause commutation failure in inverter mode. V d V k α 180 IA µ IB D X γ α 180 IA µ IB t Note: α + µ < 180 The extinction angle (γ) = α - µ V d D X = V = d 0 cosα + 3 ωl 2π k I d D X 32
33 2. HVDC Principle 6-pulse converter V d+ α=0 V d = V d+ - V d- V d+ V d V d- V d+ -V d- V d- α=0 The 6-pulse bridge consists of two 3-pulse bridges (positive and negative) connected in parallel. 33
34 2. HVDC Principle 6-pulse bridge HVDC Smoothing reactor DC line Smoothing reactor power I d power V dr power V di Reactive power I d DC line Reactive power The HVDC comprises two converters connected in anti-parallel through smoothing reactors and DC lines. One converter is operated in rectifier mode to transmit power from the AC network to the other side whereas the other side converter is operated in inverter mode to receive power into the (other side) AC network. 34
35 2. HVDC Principle Rectifier Operation of the 6-pulse bridge converter Assume α = 15 and µ = 25 cosα + cos( α + µ ) cosφ 2 o o o cos15 + cos( ) 2 o φ 30 I.cosφ V I.sinφ 30 = I The converter operates in rectifier mode. It transmits active power while consumes reactive power. 35
36 2. HVDC Principle Inverter operation of the 6-pulse bridge converter Assume α = 135 and µ = 25 cosα + cos( α + µ ) cosφ 2 o cos135 + cos(135 2 o φ 145 I.cosφ o + 25 o ) = V 145 I I.sinφ The converter operates in inverter mode. It receives active power while consumes reactive power. 36
37 2. HVDC Principle For convenience, the converter operated in inverter mode is often referred to extinction angle (γ). Thus direct voltage in inverter mode (V di ) are expressed as V d D X = V = d 0 cosα + 3 ωl 2π k I d D X, α > 90 o Vd = Vd 0 cosγ DX γ = π α µ Actually, inverter is commonly controlled at constant extinction angle to prevent commutation failure. Therefore, it is not only for convenience, but also for converter control purpose. It is important to note that voltage drop caused by commutating reactance (Dx) is now negative. 37
38 2. HVDC Principle Voltage vs. current (VI) characteristics at steady state 1.0 V V d d 0 Slope is D X α = V V d d 0 α = 0 Rectifier Inverter 1.0 Increasing α I I d dn α is the control variable for rectifier and γ is the control variable for inverter. Rectifier Inverter 1.0 Increasing γ Increasing α I I d dn -1.0 α max < γ = 0 38
39 2. HVDC Principle 12-pulse bridge HVDC Y V dr I d V di Y Y Y V dry I d V diy Y Y The 12-pulse converter is required to improve harmonic current on AC sides. It comprises two 6-pulse converters connected in series. Harmonic current on AC sides are odd orders starting from 11 th, 13 th. whereas even orders present on the DC side (12 th, 14 th ). To achieve 12-pulse, phase displacement of 30 generated by Star (Y) and Delta ( ) connection of 39the transformers are employed.
40 2. HVDC Principle V d V dy V d Rectifier operation of the 12-pulse bridge converter Assume α = 15 and µ = 25 I AY I A Y V d I A V d I A I A Y Y V dy I AY 40
41 2. HVDC Principle power ½R d power Y Y Y power I d V dr V di Y Y Y Reactive power α min < α α min = 5-7 To ensure all thyristor valves are enough forward bias to turn on. voltage ½R d decreasing α I d V dr current V di γ min < γ Reactive power γ min = To keep reactive power requirement on inverter side as low as possible. Voltage drop caused by line resistance (R d ) is taken into account and the VI characteristic presents operating point of the HVDC system. 41
42 2. HVDC Principle Detail Configuration of the HVDC 42
43 2. HVDC Principle Alternatives for the implementation of a HVDC power transmission system a) Earth Return ii) Bipolar Configuration b) Metallic Return i) Mono-polar Configuration iii) Homo-polar Configuration 43
44 2. HVDC Principle Alternatives for the implementation of a HVDC power transmission system (continued) 44
45 3. Control of the DC Transmission Can we use manual control for the rectifier (vary α) and the inverter (vary γ)? If we can not do that, which side should be controlled (rectifier or inverter) or control them both? What is/are the control purpose(s)? 45
46 3. Control of the DC Transmission Typical control strategies used in a HVDC system consists of: Firing Control {Rectifier} Current Control (CC) {Inverter} Constant Extinction Angle (CEA) Control {Inverter} Current Margin Control (CM) {Inverter} Voltage Control (VC) Voltage Dependent Current Limit (VDCL) Tap change Controls (TCC) Power Reversal 46
47 3. Control of the DC Transmission Firing Control Function of the firing control is to convert the firing angle order (α*) demanded fed into the valve group control system. There might be voltage distortions due to non-characteristic harmonics, faults and other transient disturbances such as frequency variation. Thus, phase-locked loop (PLL) based firing system is generally applied. v A v B v C Phase Detector v error u A u B u C PI Controller ( 1+ Ts) K Ts sin(.) sin(.) sin(.) v o Voltage Controlled Oscillator - ⅔ π θ α* comparator comparator comparator Gate firing 47
48 3. Control of the DC Transmission Firing Control (Continued) u A v A 0 time v error 0 2π time θ α* 0 Firing pulse of phase A α time 48
49 3. Control of the DC Transmission Current Control (CC) The firing angle is controlled with a feedback control system as shown in figure. The dc voltage of the converter increases (by decrease α*) or decreases (by increase α*) to adjust the dc current to its set-point (I d *). ( 1+ Ts) K Ts Y I d V dr v A, v B, v C Y Y i d * - i d + PI α min α max α* Firing Control 6 6 Current measurement 49
50 3. Control of the DC Transmission Constant Extinction Angle Control (CEA) The firing angle of the inverter is controlled at minimum angle (γ min ) to reduce reactive power requirement. This can be achieved by using Gamma control (γ-control). Current measurement Y V di Y Y Valve voltage γ measurement 6 6 v A, v B, v C Firing Control α* α min α max PI γ - + γ* 50
51 3. Control of the DC Transmission VI Characteristic of the CC and the CEA voltage voltage V dr α* X V di V di γ* = γ min V dr α*=α min γ* = γ min AC voltage decreasing I d current I d current VI Characteristic The intersection (X) is the operating point of the DC transmission line. If AC voltage on rectifier side decreases, CC decreases α* down to α min to increase DC current (I d ), but there is no operating point (X). This problem can be solved using CMC. 51
52 3. Control of the DC Transmission Current Margin Control (CMC) A better way is to use the inverter to control current less than of the rectifier by an amount of current margin ( I d ) when the rectifier can not perform CC. Y γ - Control γ* V di Current measurement Y Y 6 v A, v B, v C Firing Control α* Minimum selection α min α max PI + i d = 0.1 to 0.15 i d - + i d * 52
53 3. Control of the DC Transmission VI Characteristic of CC, CEA and CMC voltage voltage V dr α* X V di CEA γ* = γ min Vdr α*=α min X V di γ* = γ min CMC I d CC AC voltage decreasing Id I d current I d current Combined characteristics of CC, CEA and CMC This method can maintain stable operation when AC voltage of both sides are fluctuated. If AC voltage on rectifier side decreases, CC decreases α* down to α min to increase DC current (I d ), but there is no operating point (X). This 53 problem can be solved by CMC.
54 3. Control of the DC Transmission What will happen if AC network of the inverter side is too weak! voltage voltage V dr α* CMC X I d More Weak Weak AC V di CEA γ* = γ min V dr α* CMC I d X CEA γ* = γ min V di VC γ* > γ min I d current I d current In this range the intersection is poorly to define and both current controllers will hunt between the operating points. This problem can be solved by adjust VI characteristic of the inverter to voltage control (VC) in order to avoid hunting between two 54 controllers.
55 3. Control of the DC Transmission Voltage Control (VC) it is very effective when the inverter is connected to a weak AC network. The normal operating point X corresponds to a value of γ higher than the minimum. Thus, the inverter (rectifier as well) consumes more reactive power compared to inverter with CEA. Y Voltage measurement V di 6 Y Y v A, v B, v C 6 Firing Control α* Minimum selection Maximum selection CMC γ -Control α min α max PI v di 55 γ* v di * - +
56 3. Control of the DC Transmission Voltage Dependent Current Limit (VDCL) Commutation failures can occur during an AC fault on the inverter side. It results in continue conduction of a valve beyond its 120 conduction interval. The CC will regulate the DC current to its rated value, but in the worst case, two inverter valves may form DC short circuit and continue conducting for a long time, which can cause valve damage. To prevent this problem, DC current must be reduced. One possible to detect the AC side fault is the lowering of the DC voltage. This voltage is typically chosen at 40% of the rated voltage. I d 56
57 3. Control of the DC Transmission Voltage Dependent Current Limit (VDCL) The VDCL is a limitation imposed by the ability of the AC system to sustain the DC power flow when the AC voltage at the rectifier bus is reduced due to some disturbance as well. The VDCL characteristics is presented below. voltage V dr 0.4 VDCL α* CMC I d X VC V di 0.4 voltage V dr α* CMC VDCL I d X VC V di VDCL I d VDCL I d VDCL I dmax I d-min I dmax current I d-min I d current 57
58 3. Control of the DC Transmission Voltage Dependent Current Limit (VDCL) i d * v d v i i Minimum selection CC V d 1 1+Ts v VDCL v d Voltage measurement 58
59 3. Control of the DC Transmission Tap Change Control (TCC) When voltage of the AC system of the rectifier and/or of the inverter is fluctuated, transformer taps (both side) can adjust to keep the DC voltage within desired limits or suitable operating point. Generally, the tap will be changed when the firing angle of the rectifier/inverter still reach its more than minutes to avoid interaction of other controls. Example: if the firing angle (α) of the rectifier reaches minimum limit (α min ) for long time. It means that the AC voltage of the converter is not appropriate. Thus, AC voltage of the converter must be reduced by tap changing of the converter transformer to free the firing angle of the rectifier. 59
60 3. Control of the DC Transmission Power Reversal The VI characteristic of power reversion is presented below (VDCL and VC are not included). The station 1 (rectifier) increases firing angle (α) into the inverter region and the station 2 (inverter) decreases its firing angle (α) into rectifier region. This can be performed without altering the direction of current flow. voltage voltage V1 dr α* X γ* = γ min V2 di I d current I d current V1 di V2 dr α* X γ* = γ min 60
61 3. Control of the DC Transmission Y I d Y V dr V di Y Y Y Y Max. CC Min. α* Firing Control VDCL V d, I d,α, γ Master Control i d * Firing Control VDCL α* Min. CC Max. i d CAE VC TCC γ min V d * p*/v d p o p* p Modulation Signal Power order γ min V d * CAE VC TCC 61
62 3. Control of the DC Transmission CIGRE s HVDC benchmark was simulated on ATP-EMTP with the typical HVDC control schemes, which the CC mode was employed at rectifier and VC mode was applied at inverter. All simulation results are presented in normalized values. Rectifier Current Control Inverter Voltage Control Start Up HVDC 62
63 3. Control of the DC Transmission The HVDC started at 0.1 sec. The firing angle of rectifier started at 90 while the extinction angle of inverter started at 90. Firing Angle (α) of Rectifier Firing Angle (α) of Inverter Extinction angle (γ) is also shown Start Up HVDC 63
64 3. Control of the DC Transmission The HVDC started to reverse power flow direction at 0.5 sec. Firing angle of the rectifier increased (with a ramp rate) into inverter zone while firing angle of the inverter decreased (with a ramp rate) into rectifier zone. Firing Angle (α) of Rectifier and Inverter Power Reversal DC Current 64
65 3. Control of the DC Transmission The power flow direction of the HVDC reversed at 0.9 sec. Power Reversal 65
66 3. Control of the DC Transmission VDCL performance during 1-phase fault at AC network of the rectifier station. V a Vb Vc 1 phase Fault at AC network of the rectifier station 66
67 3. Control of the DC Transmission I REF I d Vdi p.u. Degree Alpha _ r ( α ) Alpha_i( ) r α I d I REF α i i V di α r Fault at AC network of rectifier station 67
68 3. Control of the DC Transmission VDCL performance during 1-phase fault at AC network of the inverter station. V a Vb Vc 1-phase Fault at AC network of the inverter station 68
69 3. Control of the DC Transmission p.u. I Degree Alpha _ r ( α r ) Alpha_i( α ) REF I d Vdi i I d V di I REF α i α r Fault at AC network of inverter station 69
70 3. Control of the DC Transmission Modulation signal is employed when a power system has a special requirement such as frequency control, power oscillation damping, etc. For example, the addition frequency control loop is included into HVDC control system to stabilize frequency of the AC system. 70
71 3. Control of the DC Transmission Modulation Function of EGAT-TNB HVDC 71
72 3. Control of the DC Transmission Power Swing Damping (PSD) Function of EGAT-TNB HVDC 72
73 Thank you very much for your attention
74 References 1. Ani Gole, HVDC Transmission Lecture Note, University of Manitoba, Jos Arrilaga, High Voltage Direct Current Transmission, 2 nd, IEE-Press, Dennis A. Woodford, HVDC Transmission, Manitoba HVDC Research Center, Canada, Erich Uhlmann, Power Transmission by Direct Current, Springer Verlag, Vijay K. Sood, HVDC and FACTS Controllers, Kluwer Edward Wilson Kimbark, Direct Current Transmission vol.1, Wiley- Interscience, IEEE Transmission and Distribution Committee, IEEE guide for planning DC links terminating at AC locations having low short-circuit capacities, IEEE, กฤตยา สมส ย, น ท ศน วรพนพ พ ฒน, ว ทว ส ผ องญาต, การจ าลองระบบส งไฟฟ าแรงส ง กระแสตรงโดย ATP-EMTP, ส มมนาว ชาการระบบส ง กฟผ
High Voltage DC Transmission 2
High Voltage DC Transmission 2 1.0 Introduction Interconnecting HVDC within an AC system requires conversion from AC to DC and inversion from DC to AC. We refer to the circuits which provide conversion
More informationChapter -3 ANALYSIS OF HVDC SYSTEM MODEL. Basically the HVDC transmission consists in the basic case of two
Chapter -3 ANALYSIS OF HVDC SYSTEM MODEL Basically the HVDC transmission consists in the basic case of two convertor stations which are connected to each other by a transmission link consisting of an overhead
More informationUnit-II----Analysis of HVDC Converters
Unit-II----Analysis of HVDC Converters Introduction: HVDC converters converts AC to DC and transfer the DC power, then DC is again converted to AC by using inverter station. HVDC system mainly consists
More informationHVDC Control System - Overview
HVDC Control System - Overview HVDC Control & Protection What are the basic control principles for HVDC Systems? HVDC Control What are the basic principles of HVDC Controls? I d U 1 U 2 AC System A AC
More informationDynamic Performance Evaluation of an HVDC Link following Inverter Side Disturbances
174 ACTA ELECTROTEHNICA Dynamic Performance Evaluation of an HVDC Link following Inverter Side Disturbances S. HADJERI, S.A. ZIDI, M.K. FELLAH and M. KHATIR Abstract The nature of AC/DC system interactions
More informationPower Upgrading of Transmission Line by Injecting DC Power in to AC Line with the help of ZIG-ZAG Transformer
Power Upgrading of Transmission Line by Injecting DC Power in to AC Line with the help of ZIG-ZAG Transformer C.GOPI*, M.KISHOR** *(Department. of Electrical and Electronics Engineering, SVPCET, Puttur)
More informationDr.Arkan A.Hussein Power Electronics Fourth Class. Operation and Analysis of the Three Phase Fully Controlled Bridge Converter
Operation and Analysis of the Three Phase Fully Controlled Bridge Converter ١ Instructional Objectives On completion the student will be able to Draw the circuit diagram and waveforms associated with a
More informationHigh Voltage Direct Current Transmission
High Voltage Direct Current Transmission 11 11.0 Historical Background Power Transmission was initially carried out in the early 1880s using Direct Current (d.c.). With the availability of transformers
More informationv o v an i L v bn V d Load L v cn D 1 D 3 D 5 i a i b i c D 4 D 6 D 2 Lecture 7 - Uncontrolled Rectifier Circuits III
Lecture 7 - Uncontrolled Rectifier Circuits III Three-phase bridge rectifier (p = 6) v o n v an v bn v cn i a i b i c D 1 D 3 D 5 D 4 D 6 D d i L R Load L Figure 7.1 Three-phase diode bridge rectifier
More informationIMPORTANCE OF VSC IN HVDC
IMPORTANCE OF VSC IN HVDC Snigdha Sharma (Electrical Department, SIT, Meerut) ABSTRACT The demand of electrical energy has been increasing day by day. To meet these high demands, reliable and stable transmission
More informationU I. HVDC Control. LCC Reactive power characteristics
Lecture 29 HVDC Control Series Compensation 1 Fall 2017 LCC Reactive power characteristics LCC HVDC Reactive compensation by switched filters and shunt capacitor banks Operates at lagging power factor
More informationB4-212 OPERATING EXPERIENCES AND RESULTS OF ON-LINE EXTINCTION ANGLE CONTROL IN KII CHANNEL HVDC LINK
21, rue d'artois, F-75008 Paris http://www.cigre.org B4-212 Session 2004 CIGRÉ OPERATING EXPERIENCES AND RESULTS OF ON-LINE EXTINCTION ANGLE CONTROL IN KII CHANNEL HVDC LINK M. Takasaki * T. Sato, S. Hara
More informationTSTE19 Power Electronics. Lecture3 Tomas Jonsson ICS/ISY
TSTE19 Power Electronics Lecture3 Tomas Jonsson ICS/ISY 2015-11-09 2 Outline Rectifiers Current commutation Rectifiers, cont. Three phase 2015-11-09 3 Effect of L s on current commutation Current commutation
More informationTopics in JNTU Syllabus Modules and Sub Modules Lecture. Basic characteristics L21 T1-Ch4, T2-Ch14 Characteristics. Modification of the control
SESSION PLAN Sl. Topics in JNTU Syllabus Modules and Sub Modules UNIT-III 9 Principal of DC link control Introduction Steady state equivalent circuit of a 2 terminal DC link Lecture L20 Suggested Books
More informationImprovement of Rotor Angle Stability and Dynamic Performance of AC/DC Interconnected Transmission System
Improvement of Rotor Angle Stability and Dynamic Performance of AC/DC Interconnected Transmission System 1 Ramesh Gantha 1, Rasool Ahemmed 2 1 eee Kl University, India 2 AsstProfessor, EEE KL University,
More informationChapter 4. HVDC Controls 4.1 HISTORICAL BACKGROUND
Chapter 4 HVDC Controls The historical background to the developments that took place in the evolution of HVDC controllers will be presented in this chapter. The basis and formulations of modern controllers
More informationPower Flow Control And Total Harmonic Distortion Reduction In HVDC Link Using PI And ANN Controllers
IOSR Journal of Electrical and Electronics Engineering (IOSR-JEEE) e-issn: 2278-1676,p-ISSN: 2320-3331, Volume 13, Issue 5 Ver. I (Sep. Oct. 2018), PP 10-20 www.iosrjournals.org Power Flow Control And
More informationEnhancement of AC System Stability using Artificial Neural Network Based HVDC System
Volume: 02 Issue: 03 June-2015 www.irjet.net p-issn: 2395-0072 Enhancement of AC System Stability using Artificial Neural Network Based HVDC System DR.S.K.Bikshapathy 1, Ms. Supriya Balasaheb Patil 2 1
More informationInvestigation of D-Statcom Operation in Electric Distribution System
J. Basic. Appl. Sci. Res., (2)29-297, 2 2, TextRoad Publication ISSN 29-434 Journal of Basic and Applied Scientific Research www.textroad.com Investigation of D-Statcom Operation in Electric Distribution
More informationPower Transmission of AC-DC Supply in a Single Composite Conductor
IJIRST International Journal for Innovative Research in Science & Technology Volume 2 Issue 03 August 2015 ISSN (online): 2349-6010 Power Transmission of AC-DC Supply in a Single Composite Conductor P.
More informationBHARATHIDASAN ENGINEERING COLLEGE, NATTRAMPALLI DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING UNIT I
BHARATHIDASAN ENGINEERING COLLEGE, NATTRAMPALLI DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING FAQ-EE6010 HIGH VOLTAGE DC TRANSMISSION UNIT I Part -A 1. List out two merits of AC and DC transmission
More informationControl of Wind Power Plant for Cooperation with Conventional Power Generation Unit and HVDC Classic Link
Control of Wind Power Plant for Cooperation with Conventional Power Generation Unit and HVDC Classic Link Li-Jun Cai*, Simon Jensen **, Vincenz Dinkhauser***, István Erlich**** REpower Systems SE,. Albert-Betz-Strasse,
More informationAssessment of Saturable Reactor Replacement Options
Assessment of Saturable Reactor Replacement Options D.T.A Kho, K.S. Smith Abstract-- The performance of the dynamic reactive power compensation provided by the existing variable static compensation (STC)
More informationPower Electronics (BEG335EC )
1 Power Electronics (BEG335EC ) 2 PURWANCHAL UNIVERSITY V SEMESTER FINAL EXAMINATION - 2003 The figures in margin indicate full marks. Attempt any FIVE questions. Q. [1] [a] A single phase full converter
More informationVolume 4, Number 1, 2018 Pages 1-14 Jordan Journal of Electrical Engineering ISSN (Print): , ISSN (Online):
JJEE Volume 4, Number 1, 2018 Pages 1-14 Jordan Journal of Electrical Engineering ISSN (Print): 2409-9600, ISSN (Online): 2409-9619 Control of Multi-Level Converter Using By-Pass Switches Rasha G. Shahin
More informationPower Flow Control in HVDC Link Using PI and Ann Controllers
International Journal of Engineering Research and Development e-issn: 2278-067X, p-issn : 2278-800X, www.ijerd.com Volume 4, Issue 9 (November 2012), PP. 52-58 Power Flow Control in HVDC Link Using PI
More information12 Three-phase Controlled Rectifiers
12 Three-phase Controlled Rectifiers Juan W. Dixon, Ph.D. Department of Electrical Engineering, Pontificia Universidad Católica de Chile Vicuña Mackenna 4860, Santiago, Chile 12.1 Introduction... 201 12.2
More informationHigh Voltage DC Transmission Prof. Dr. S. N. Singh Department of Electrical Engineering Indian Institute of Technology Kanpur
High Voltage DC Transmission Prof. Dr. S. N. Singh Department of Electrical Engineering Indian Institute of Technology Kanpur Module No. # 01 Lecture No. # 03 So, in last two lectures, we saw the advantage
More informationPOWER QUALITY ENHANCEMENT BY DC LINK SUPPLIED INDUSTRIAL SYSTEM
POWER QUALITY ENHANCEMENT BY DC LINK SUPPLIED INDUSTRIAL SYSTEM A.Karthikeyan Dr.V.Kamaraj Sri Venkateswara College of Engineering Sriperumbudur, India-602105. Abstract: In this paper HVDC is investigated
More informationINSTANTANEOUS POWER CONTROL OF D-STATCOM FOR ENHANCEMENT OF THE STEADY-STATE PERFORMANCE
INSTANTANEOUS POWER CONTROL OF D-STATCOM FOR ENHANCEMENT OF THE STEADY-STATE PERFORMANCE Ms. K. Kamaladevi 1, N. Mohan Murali Krishna 2 1 Asst. Professor, Department of EEE, 2 PG Scholar, Department of
More informationModule 4. AC to AC Voltage Converters. Version 2 EE IIT, Kharagpur 1
Module 4 AC to AC Voltage Converters Version 2 EE IIT, Kharagpur 1 Lesson 31 Three-ase to Threease Cyclo-converters Version 2 EE IIT, Kharagpur 2 Instructional Objectives Study of the following: The three-ase
More information( ) ON s inductance of 10 mh. The motor draws an average current of 20A at a constant back emf of 80 V, under steady state.
1991 1.12 The operating state that distinguishes a silicon controlled rectifier (SCR) from a diode is (a) forward conduction state (b) forward blocking state (c) reverse conduction state (d) reverse blocking
More informationUnit-3-A. AC to AC Voltage Converters
Unit-3-A AC to AC Voltage Converters AC to AC Voltage Converters This lesson provides the reader the following: AC-AC power conversion topologies at fixed frequency Power converter options available for
More informationChapter 2 Shunt Active Power Filter
Chapter 2 Shunt Active Power Filter In the recent years of development the requirement of harmonic and reactive power has developed, causing power quality problems. Many power electronic converters are
More informationHVDC Transmission Using Artificial Neural Networks Based Constant Current and Extension Angle Control
HVDC Transmission Using Artificial Neural Networks Based Constant Current and Extension Angle Control V. Chandra Sekhar Department of Electrical and Electronics Engineering, Andhra University College of
More informationR. W. Erickson. Department of Electrical, Computer, and Energy Engineering University of Colorado, Boulder
R. W. Erickson Department of Electrical, Computer, and Energy Engineering University of Colorado, Boulder 16.4. Power phasors in sinusoidal systems Apparent power is the product of the rms voltage and
More informationConventional Paper-II-2011 Part-1A
Conventional Paper-II-2011 Part-1A 1(a) (b) (c) (d) (e) (f) (g) (h) The purpose of providing dummy coils in the armature of a DC machine is to: (A) Increase voltage induced (B) Decrease the armature resistance
More informationPOWER ELECTRONICS LAB MANUAL
JIS College of Engineering (An Autonomous Institution) Department of Electrical Engineering POWER ELECTRONICS LAB MANUAL Exp-1. Study of characteristics of an SCR AIM: To obtain the V-I characteristics
More informationDesign and Simulation of Passive Filter
Chapter 3 Design and Simulation of Passive Filter 3.1 Introduction Passive LC filters are conventionally used to suppress the harmonic distortion in power system. In general they consist of various shunt
More informationANALYSIS OF RECOVERY FROM COMMUTATION FAILURES IN AN HVDC INVERTER CONNECTED TO A WEAK RECEIVING AC SYSTEM
44 Acta Electrotechnica et Informatica Vol. 8, No. 1, 2008, 44 50 ANALYSIS OF RECOVERY FROM COMMUTATION FAILURES IN AN HVDC INVERTER CONNECTED TO A WEAK RECEIVING AC SYSTEM Mohamed KHATIR, Sid Ahmed ZIDI,
More informationCurso de Transmissão em Corrente Continua Rio de Janeiro, de Junho, 2007
Curso de Transmissão em Corrente Continua Rio de Janeiro, 13 15 de Junho, 2007 DC Harmonic Filters Page 1 of 9 1 Function of the DC-Side Harmonic Filters Harmonic voltages which occur on the dc-side of
More informationA cost effective hybrid HVDC transmission system with high performance in DC line fault handling
2, rue d Artois, F-758 PARIS B4-7 CIGRE 28 http : //www.cigre.org A cost effective hybrid HVDC transmission system with high performance in DC line fault handling Mats Andersson, Xiaobo ang and ing-jiang
More information3 CHAPTER III DESIGN, MODELING AND CONTROL OF VSC BASED HVDC SYSTEM
3 CHAPTER III DESIGN, MODELING AND CONTROL OF VSC BASED HVDC SYSTEM The voltage source converter (VSC) is the prime unit of a VSC based HVDC system, therefore, its design and performance evaluation is
More informationConventional Paper-II-2013
1. All parts carry equal marks Conventional Paper-II-013 (a) (d) A 0V DC shunt motor takes 0A at full load running at 500 rpm. The armature resistance is 0.4Ω and shunt field resistance of 176Ω. The machine
More informationPower Quality enhancement of a distribution line with DSTATCOM
ower Quality enhancement of a distribution line with DSTATCOM Divya arashar 1 Department of Electrical Engineering BSACET Mathura INDIA Aseem Chandel 2 SMIEEE,Deepak arashar 3 Department of Electrical
More informationA Thyristor Controlled Three Winding Transformer as a Static Var Compensator
Abstract: A Thyristor Controlled Three Winding Transformer as a Static Var Compensator Vijay Bendre, Prof. Pat Bodger, Dr. Alan Wood. Department of Electrical and Computer Engineering, The University of
More informationHVDC High Voltage Direct Current
HVDC High Voltage Direct Current Typical HVDC Station BACK TO BACK CONVERTER STATION MONO POLAR WITH GROUND RETURN PA Back to Back Converters indicates that the Rectifiers & Inverters are located in the
More informationDESIGN SYNTHESIS OF LCC HVDC CONTROL SYSTEMS
DESIGN SYNTHESIS OF LCC HVDC CONTROL SYSTEMS LEON CHETTY IN FULFILLMENT OF DOCTOR OF PHILOSOPHY DEGREE FACULTY OF ENGINEERING UNIVERSITY OF KWAZULU NATAL September 011 SUPERVISOR: PROFESSOR N.M. IJUMBA
More informationLecture 4 - Three-phase circuits, transformer and transient analysis of RLC circuits. Figure 4.1
Lecture 4 - Three-phase circuits, transformer and transient analysis of RLC circuits Power supply to sizeable power converters are often from three-phase AC source. A balanced three-phase source consists
More informationHighgate Converter Overview. Prepared by Joshua Burroughs & Jeff Carrara IEEE PES
Highgate Converter Overview Prepared by Joshua Burroughs & Jeff Carrara IEEE PES Highgate Converter Abstract Introduction to HVDC Background on Highgate Operation and Control schemes of Highgate 22 Why
More informationCommissioning of a twelve-pulse-bridges LCC-HVDC Analog-Hybrid-Simulator
Commissioning of a twelvepulsebridges LCCHVDC AnalogHybridSimulator Alexander Raab, Christoph Hahn, Klaus Schneider, Gerhard Czerwenka, Johannes Floth Institute of Electrical Energy Systems FriedrichAlexanderUniversity
More informationDr.Arkan A.Hussein Power Electronics Fourth Class. 3-Phase Voltage Source Inverter With Square Wave Output
3-Phase Voltage Source Inverter With Square Wave Output ١ fter completion of this lesson the reader will be able to: (i) (ii) (iii) (iv) Explain the operating principle of a three-phase square wave inverter.
More informationLecture Note. Uncontrolled and Controlled Rectifiers
Lecture Note 7 Uncontrolled and Controlled Rectifiers Prepared by Dr. Oday A Ahmed Website: https://odayahmeduot.wordpress.com Email: 30205@uotechnology.edu.iq Scan QR single-phase diode and SCR rectifiers
More informationChapter 10: Compensation of Power Transmission Systems
Chapter 10: Compensation of Power Transmission Systems Introduction The two major problems that the modern power systems are facing are voltage and angle stabilities. There are various approaches to overcome
More informationDynamic Phasors for Small Signal Stability Analysis
for Small Signal Stability Analysis Chandana Karawita (Transgrid Solutions) for Small Signal Stability Analysis Outline Introduction 1 Introduction Simulation and Analysis Techniques Typical Outputs Modelling
More informationHVDC. for beginners and beyond
for beginners and beyond PIONEERING HVDC SINCE 1962 Our timeline 1962 1968 1989 1996 1998 2004 Stafford UK English Electric GEC GEC - Alsthom Alstom AREVA France CGEE - Alsthom USA GE Germany AEG ( German
More informationIJEETC. InternationalJournalof. ElectricalandElectronicEngineering& Telecommunications.
IJEETC www.ijeetc.com InternationalJournalof ElectricalandElectronicEngineering& Telecommunications editorijeetc@gmail.com oreditor@ijeetc.com Int. J. Elec&Electr.Eng&Telecoms. 2015 Anoop Dhayani A P et
More informationPrinciples of HVDC Transmission
Principles of HVDC Transmission Course No: E04-036 Credit: 4 PDH Velimir Lackovic, Char. Eng. Continuing Education and Development, Inc. 9 Greyridge Farm Court Stony Point, NY 10980 P: (877) 322-5800 F:
More informationELEC387 Power electronics
ELEC387 Power electronics Jonathan Goldwasser 1 Power electronics systems pp.3 15 Main task: process and control flow of electric energy by supplying voltage and current in a form that is optimally suited
More informationLECTURE.3 : AC-DC CONVERSION
LECTURE.3 : AC-DC CONVERSION (RECTIFICATIONS) 3.1Basic Rectifier Circuits Several types of rectifier circuits are available: single-phase and three-phase half-wave and full-wave, controlled and uncontrolled,
More informationReactive Power and AC Voltage Control of LCC HVDC System with Digitally Tunable Controllable Capacitors
International Journal for Modern Trends in Science and Technology Volume: 03, Issue No: 06, June 2017 ISSN: 2455-3778 http://www.ijmtst.com Reactive Power and AC Voltage Control of LCC HVDC System with
More informationModelling of the back-to-back converter between Uruguay and Brazil in A.T.P.
Modelling of the back-to-back converter between Uruguay and Brazil in A.T.P. M. Sc. Ing. Graciela Calzolari 1, Ing. Michel Artenstein 1, Ing. Alejandro Segade 1, and Ing. Freddy Rabín 1 (1) Dept. of Transmission
More informationHVDC CAPACITOR COMMUTATED CONVERTERS IN WEAK NETWORKS GUNNAR PERSSON, VICTOR F LESCALE, ALF PERSSON ABB AB, HVDC SWEDEN
HVDC CAPACITOR COMMUTATED CONVERTERS IN WEAK NETWORKS GUNNAR PERSSON, VICTOR F LESCALE, ALF PERSSON ABB AB, HVDC SWEDEN Summary Capacitor Commutated Converters (CCC) were introduced to the HVDC market
More informationSymmetrical Component Analysis of Multi-Pulse Converter Systems
Electric Power Components and Systems ISSN: 1532-5008 (Print) 1532-5016 (Online) Journal homepage: http://www.tandfonline.com/loi/uemp20 Symmetrical Component Analysis of Multi-Pulse Converter Systems
More informationCHAPTER 4 HARMONICS AND POWER FACTOR
4.1 Harmonics CHAPTER 4 HARMONICS AND POWER FACTOR In this research a comparative study of practical aspects of mixed use of diode and Thyristor converter technologies in Aluminium Smelters has been carried
More informationThe typical ratio of latching current to holding current in a 20 A thyristor is (A) 5.0 (B) 2.0 (C) 1.0 (D) 0.5
CHAPTER 9 POWER ELECTRONICS YEAR 0 ONE MARK MCQ 9. MCQ 9. A half-controlled single-phase bridge rectifier is supplying an R-L load. It is operated at a firing angle α and the load current is continuous.
More information(a) average output voltage (b) average output current (c) average and rms values of SCR current and (d) input power factor. [16]
Code No: 07A50204 R07 Set No. 2 1. A single phase fully controlled bridge converter is operated from 230 v, 50 Hz source. The load consists of 10Ω and a large inductance so as to reach the load current
More informationAnalysis of Effect on Transient Stability of Interconnected Power System by Introduction of HVDC Link.
Analysis of Effect on Transient Stability of Interconnected Power System by Introduction of HVDC Link. Mr.S.B.Dandawate*, Mrs.S.L.Shaikh** *,**(Department of Electrical Engineering, Walchand College of
More informationVoltage-Current and Harmonic Characteristic Analysis of Different FC-TCR Based SVC
Voltage-Current and Harmonic Characteristic Analysis of Different FC-TCR Based SVC Mohammad Hasanuzzaman Shawon, Zbigniew Hanzelka, Aleksander Dziadecki Dept. of Electrical Drive & Industrial Equipment
More informationPOWER ELECTRONICS PO POST GRAD POS UATE 2010 AC Ch AC o Ch p o per Prepare Prep d are by: d Dr. Gamal Gam SOwilam SOwila 11 December 2016 ١
POWER ELECTRONICS POST GRADUATE 2010 AC Chopper Prepared by: Dr. Gamal SOwilam 11 December 2016 ١ 1. Introduction AC Chopper is An AC to AC Converter employs to vary the rms voltage across the load at
More informationLECTURE NOTES FUNDAMENTALS OF HVDC AND FACTS DEVICES. IV B.Tech II Sem (JNTU R15) Prepared by. Ms. B. Manogna Assistant Professor
LECTURE NOTES ON FUNDAMENTALS OF HVDC AND FACTS DEVICES IV B.Tech II Sem (JNTU R15) Prepared by Ms. B. Manogna Assistant Professor ELECTRICAL AND ELECTRONICS ENGINEERING INSTITUTE OF AERONAUTICAL ENGINEERING
More informationPERFORMANCE EVALUATION OF LINE AND CAPACITOR COMMUTATED CONVERTER BASED HVDC SYSTEM IN SIMULINK ENVIRONMENT
ISTANBUL UNIVERSITY JOURNAL OF ELETRIAL & ELETRONIS ENGINEERING YEAR VOLUME NUMBER :2008 : 8 : 1 (481-490) PERFORMANE EVALUATION OF LINE AND APAITOR OMMUTATED ONVERTER BASED HVD SYSTEM IN SIMULINK ENVIRONMENT
More informationINSTITUTE OF AERONAUTICAL ENGINEERING (Autonomous) Dundigal, Hyderabad
I INSTITUTE OF AERONAUTICAL ENGINEERING (Autonomous) Dundigal, Hyderabad-000 DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING TUTORIAL QUESTION BANK Course Name : POWER ELECTRONICS Course Code : AEE0
More informationATYPICAL high-power gate-turn-off (GTO) currentsource
1278 IEEE TRANSACTIONS ON INDUSTRY APPLICATIONS, VOL. 34, NO. 6, NOVEMBER/DECEMBER 1998 A Novel Power Factor Control Scheme for High-Power GTO Current-Source Converter Yuan Xiao, Bin Wu, Member, IEEE,
More informationDr.Arkan A.Hussein Power Electronics Fourth Class. Commutation of Thyristor-Based Circuits Part-I
Commutation of Thyristor-Based Circuits Part-I ١ This lesson provides the reader the following: (i) (ii) (iii) (iv) Requirements to be satisfied for the successful turn-off of a SCR The turn-off groups
More informationDynamic Stability Improvement of Power System with VSC-HVDC Transmission
Dynamic Stability Improvement of Power System with VSC-HVDC Transmission A Thesis submitted in partial fulfilment of the Requirements for the Award of the degree of Master of Technology In Industrial Electronics
More informationSimulation Study of a Monopole HVDC Transmission System Feeding a Very Weak AC Network with Firefly Algorithm Based Optimal PI Controller
Simulation Study of a Monopole HVDC Transmission System Feeding a Very Weak AC Network with Firefly Algorithm Based Optimal PI Controller S. Singaravelu, S. Seenivasan Abstract This paper presents a simulation
More informationPower Flow Control in HVDC-Link Using Artificial Neural Networks
Power Flow Control in HVDC-Link Using Artificial Neural Networks Potnuru.Chandra Mouli M.Tech Student, Department of EEE, Sri Sivani Institute Of Technology. M.Anusha, M.Tech, Assistant Professor, Department
More informationInvestigation of Hybrid Pseudo Bipolar HVDC Performances Supply Power to Passive AC Network
Sensors & Transducers, Vol. 75, Issue 7, July 4, pp. 36-3 Sensors & Transducers 4 by IFSA Publishing, S. L. http://www.sensorsportal.com Investigation of Hybrid Pseudo Bipolar HVDC Performances Supply
More information6. Explain control characteristics of GTO, MCT, SITH with the help of waveforms and circuit diagrams.
POWER ELECTRONICS QUESTION BANK Unit 1: Introduction 1. Explain the control characteristics of SCR and GTO with circuit diagrams, and waveforms of control signal and output voltage. 2. Explain the different
More informationHigh Voltage DC Transmission Prof. S. N. Singh Department of Electrical Engineering Indian institute of Technology, Kanpur
High Voltage DC Transmission Prof. S. N. Singh Department of Electrical Engineering Indian institute of Technology, Kanpur Module No: # 01 Lecture No: # 01 Evolution of HVDC Transmission Welcome to this
More informationInsulation Co-ordination For HVDC Station
Insulation Co-ordination For HVDC Station Insulation Co-ordination Definitions As per IEC 60071 Insulation Coordination is defined as selection of dielectric strength of equipment in relation to the operating
More informationDamping of Sub-synchronous Resonance and Power Swing using TCSC and Series capacitor
Damping of Sub-synchronous Resonance and Power Swing using TCSC and Series capacitor Durga Prasad Ananthu Assistant Professor, EEE dept. Guru Nanak Dev Engg College, Bidar adp.ananthu@gmail.com Rami Reddy
More informationDynamic Performance Comparison of Conventional and Capacitor Commutated Converter (CCC) for HVDC Transmission System in Simulink Environment
Dynamic Performance omparison of onventional and apacitor ommutated onverter () for HVD Transmission System in Simulink Environment Khatir M, Zidi S A, Fellah M K and Hadjeri S Electrical Engineering Department
More informationStability Enhancement for Transmission Lines using Static Synchronous Series Compensator
Stability Enhancement for Transmission Lines using Static Synchronous Series Compensator Ishwar Lal Yadav Department of Electrical Engineering Rungta College of Engineering and Technology Bhilai, India
More informationIntroduction to HVDC Transmission. High Voltage Direct Current (HVDC) Transmission
Lecture 29 Introduction to HVDC Transmission Series Compensation 1 Fall 2003 High Voltage Direct Current (HVDC) Transmission Update to Edison s Vision AC Power Generation at Relatively Lower Voltage» Step
More informationPULSE MULTIPLICATION IN FORCED- COMMUTATED CURRENT SOURCE CONVERTERS BY DC RIPPLE REINJECTION
Queensland University of Technology From the SelectedWorks of Lasantha Bernard Perera Spring September 26, 2004 PULSE MULTIPLICATION IN FORCED- COMMUTATED CURRENT SOURCE CONVERTERS BY DC RIPPLE REINJECTION
More informationQuestions from the same exercise can be combined together to increase difficulty. Which one of the following properties of the diode is NOT true:
Questions from the same exercise can be combined together to increase difficulty. 21 1 Which one of the following properties of the diode is NOT true: a) When no voltage is applied across the diode, it
More informationVoltage Source Converter Modelling
Voltage Source Converter Modelling Introduction The AC/DC converters in Ipsa represent either voltage source converters (VSC) or line commutated converters (LCC). A single converter component is used to
More informationSimulation & Implementation of Single-Phase Controlled Rectifier
1.0 INTRODUCTION 1.1 Significance This thesis will take a better insight of design and implementation of single-phase controlled rectifier by applying thyristor, namely Silicon Controlled Rectifier (SCR).
More informationVoltage and Current Waveforms Enhancement using Harmonic Filters
Voltage and Current Waveforms Enhancement using Harmonic Filters Rajeb Ibsaim rabsaim@yahoo.com, Azzawia University, Libya Amer Daeri ibnjubair1@yahoo.co.uk Azzawia University, Libya Abstract The demand
More informationIntroduction to HVDC VSC HVDC
Introduction to HVDC VSC HVDC Dr Radnya A Mukhedkar Group Leader, Senior Principal Engineer System Design GRID August 2010 The Voltage Sourced Converter Single Phase Alternating Voltage Output Steady DC
More informationZ-SOURCE INVERTER BASED DVR FOR VOLTAGE SAG/SWELL MITIGATION
Z-SOURCE INVERTER BASED DVR FOR VOLTAGE SAG/SWELL MITIGATION 1 Arsha.S.Chandran, 2 Priya Lenin 1 PG Scholar, 2 Assistant Professor 1 Electrical & Electronics Engineering 1 Mohandas College of Engineering
More informationISSN: Page 20. International Journal of Engineering Trends and Technology- Volume2Issue3-2011
Design of Shunt Active Power Filter to eliminate the harmonic currents and to compensate the reactive power under distorted and or imbalanced source voltages in steady state Sangu Ravindra #1, Dr.V.C.Veera
More informationCHIEF ENGINEER REG III/2 MARINE ELECTROTECHNOLOGY
CHIEF ENGINEER REG III/2 MARINE ELECTROTECHNOLOGY LIST OF TOPICS 1 Electric Circuit Principles 2 Electronic Circuit Principles 3 Generation 4 Distribution 5 Utilisation The expected learning outcome is
More informationA new control scheme for an HVDC transmission link with capacitorcommutated converters having the inverter operating with constant alternating voltage
21, rue d Artois, F-758 PARIS B4_16_212 CIGRE 212 http : //www.cigre.org A new control scheme for an HVDC transmission link with capacitorcommutated converters having the inverter operating with constant
More informationCHAPTER 1 DIODE CIRCUITS. Semiconductor act differently to DC and AC currents
CHAPTER 1 DIODE CIRCUITS Resistance levels Semiconductor act differently to DC and AC currents There are three types of resistances 1. DC or static resistance The application of DC voltage to a circuit
More informationSingle-Phase Half-Wave Rectifiers
ectifiers Single-Phase Half-Wave ectifiers A rectifier is a circuit that converts an ac signal into a unidirectional signal. A single-phase half-way rectifier is the simplest type. Although it is not widely
More informationVSC Based HVDC Active Power Controller to Damp out Resonance Oscillation in Turbine Generator System
VSC Based HVDC Active Power Controller to Damp out Resonance Oscillation in Turbine Generator System Rajkumar Pal 1, Rajesh Kumar 2, Abhay Katyayan 3 1, 2, 3 Assistant Professor, Department of Electrical
More informationELEC4240/ELEC9240 POWER ELECTRONICS
THE UNIVERSITY OF NEW SOUTH WALES FINAL EXAMINATION JUNE/JULY, 2003 ELEC4240/ELEC9240 POWER ELECTRONICS 1. Time allowed: 3 (three) hours 2. This paper has six questions. Answer any four. 3. All questions
More information