Pole, zero and Bode plot
|
|
- Brooke Owen
- 6 years ago
- Views:
Transcription
1 Pole, zero and Bode plot EC Lecture notes YESAREKEY December 12, 2007 Authored by: Ramesh.K
2 Pole, zero and Bode plot EC Lecture notes A rational transfer function H (S) can be expressed as a ratio of a numerator polynomial n(s) divided by a denominator polynomial d(s), Mathematically, Where s=pi is a finite of H( S ), s=z i is called a finite zero of H(S), and K is the gain constant of transfer function H( S ). Generally z 1..z n are called the transfer function zeros and p 1..p n are called transfer function poles. They can be either real or complex. The complex poles or zeros must occur in conjugate pairs. A finite pole satisfies as, and a finite zero satisfies. BODE PLOTS H. bode developed a technique for computing approximate or asymptotic frequency response curves-called Bode plots. The technique is particularly useful in the case of real poles and zeros. A Bode magnitude plot is a graph, with a linear scale for the db values on the vertical axis and a logarithmic scale for ω on the horizontal axis, to show the transfer function or frequency response of a linear, time-invariant system. The magnitude axis of the Bode plot is usually expressed as decibels, that is, 20 times the common logarithm of the amplitude gain. With the magnitude gain being logarithmic, bode plots make multiplication of magnitudes a simple matter of adding distances on the graph (in decibels), since. A Bode phase plot is a graph of phase versus frequency, also plotted on a log-frequency axis, usually used in conjunction with the magnitude plot, to evaluate how much a frequency will be phase-shifted. The Amplifier Transfer function Amplifiers have frequency gain function either of the following two forms. The only diff b/w the two is that gain of ac amplifiers falls at low frequencies. The Frequency Bands As shown in the fig.b the amplifier gain is almost constant over a wide frequency range called the mid band. In this frequency almost all capacitors (coupling, bypass, internal capacitance have negligible effect and can be ignored in the gain calculations. At high frequencies the gain falls due to the internal capacitance of the device. Also at low frequencies the bypass capacitors will not act (a) (b) 1
3 as a short circuit for ac, hence the gain falls. The extend of frequencies are defined by the two frequencies, these are frequencies at which the gain drops by 3dB below the value at midband. The amplifier band width can be defined as Since Hence the gain band width product : where is the amp gain. The low freq amp gain can be expressed by, The high freq gain For and EFFECT OF FEEDBACK ON THE AMPLIFIER POLES : The amplifier frequency response and stability are directly determined by its poles. Stability and Pole location: The poles of the feedback amp can be obtained by solving the characteristic equation, 0 For an amplifier to be stable, its pole should lie in the left half of the s- plane. A pair of conjugate poles on the axis gives rise to sustained sinusoidal oscillations. Poles in the right half of the s plane gives rise to growing oscillations, as shown below. STUDY OF STABLILITY OF FEED BACK AMPLIFIERS USING BODE PLOTS If the feedback is termed as negative feedback and if the feedback is termed as positive or regenerative. Under these circumstances, the resultant transfer gain will be greater than, 2
4 the nominal gain without feed back. Since amplifier with positive feedback, this method is seldom used. (used in oscillators). Because of the reduced stability of an To illustrate the instability of amplifiers with positive feedback, consider the following situation: no signal is applied, but because of some transient disturbances, a signal X o appears at the o/p. a portion of this signal, back to the i/p circuit, and will appear in the o/p as an increased signal spurious o/p has regenerated itself. In other words, if, will be fed. If this term just equals X o, then the, the amplifier will oscillate. Hence, if an attempt is made to obtain large gain by making almost equals to unity, there is the possibility that the amplifier may break put into spontaneous oscillation. There is little point in attempting to achieve amplification at the expense of stability. The condition for Stability: In the design of a feedback amplifier, it must be ascertained that the circuit is stable at all frequencies. i.e., the system is stable if a transient disturbance results in a response which dies out. The stability of an amplifier depends on pole of its transfer function. As described above, if a pole exists with a positive real part, this will result in a disturbance increasing exponentially with time. Hence the condition which must be satisfied, if a system is to be stable, is that the pole of the transfer function must all lie on the left hand half of the s plane. If a system without feedback is stable, the poles of A do lie in the left hand half plane. It follows from the Eqn that the stability condition requires that the zeros of all lie in the left hand half of the s- plane. Gain and phase margins: It should be noted that instead of plotting the product in the complex plane, it is more convenient to plot the magnitude, usually in decibels, and also the phase of as a function of frequency. If we can show that is less than unity (<0 db) when the phase angle of is 180 o, the closed loop amplifier will be stable. The gain margin is defined as the value of in db at the frequency at which the phase angle of is 180 o.if the gain margin is negative this gives the db rise in open loop gain, which is theoretically permissible without oscillation. If the gain margin is positive, the amplifier is potentially unstable. Feedback amplifiers are usually designed to have sufficient gain margin to allow for the inevitable changes in the loop gain with temp, time and so on. The phase margin is 180 o minus the magnitude of the angle of at the frequency at which is unity (0 db).the magnitude of these quantities gives an indication of how stable Bode plots relating to the defn: of gain and phase margins an amplifier is. For E.g., a linear amp of good stability requires gain and phase margins of at least 10 db and 50 o respectively. The amount of phase margin has a profound effect on the shape of the closed loop magnitude response. 3
5 References Micro Electronic Circuits, Sedra/Smith, 4 th edition. Integrated Electronics: Analog and Digital Circuits And Systems ; Millman & Halkias Wikipedia, the free encyclopedia Lecture Notes 4
6 S.R.K Ramesh.K /ECE/MEA EC 12/20/2007 Steps to draw Bode plots Lecture Notes-EC04 # 303#ECNT
7 Ramesh.K /ECE/MEA EC Steps to draw Bode plots Lecture Notes-EC04 # 303#ECNT Steps to Plot Bode Magnitude Plot Let H(s) be the transfer function.covert H(s) into the form, then replace s by jω. List the corner frequencies (i.e, the coefficients of jω s of H(s)) in the increasing order and prepare a table as given below. Terms Corner Frequencies Change in slope In the table enter K or or K as the first term and the other term as the increasing order of the corner frequencies. Choose an arbitrary frequency ω L, less than the lowest corner frequency. Calculate the gain in db magnitude of K or or K at ω L and at the lower corner frequency. Calculate the gain at every corner frequency one by one using the formula given below. Chose an arbitrary frequency ω H, greater than the highest corner frequency. Calculate the gain at ω H using the above formula. Plot the Bode magnitude plot [A (db).vs. log (ω)] in a semi log graph. Steps to Plot Bode Phase Plot: Calculate the phase angle of H(jω) for various values of ω and are tabulated. The choices of frequencies are preferably the frequency selected for magnitude plot. Magnitude and phase of a complex umber: Phase: 1
Bode plot, named after Hendrik Wade Bode, is usually a combination of a Bode magnitude plot and Bode phase plot:
Bode plot From Wikipedia, the free encyclopedia A The Bode plot for a first-order (one-pole) lowpass filter Bode plot, named after Hendrik Wade Bode, is usually a combination of a Bode magnitude plot and
More informationMicroelectronic Circuits II. Ch 9 : Feedback
Microelectronic Circuits II Ch 9 : Feedback 9.9 Determining the Loop Gain 9.0 The Stability problem 9. Effect on Feedback on the Amplifier Poles 9.2 Stability study using Bode plots 9.3 Frequency Compensation
More informationBoise State University Department of Electrical and Computer Engineering ECE 212L Circuit Analysis and Design Lab
Objectives Boise State University Department of Electrical and Computer Engineering ECE L Circuit Analysis and Design Lab Experiment #0: Frequency esponse Measurements The objectives of this laboratory
More informationBode Plots. Hamid Roozbahani
Bode Plots Hamid Roozbahani A Bode plot is a graph of the transfer function of a linear, time-invariant system versus frequency, plotted with a logfrequency axis, to show the system's frequency response.
More informationCHAPTER 9 FEEDBACK. NTUEE Electronics L.H. Lu 9-1
CHAPTER 9 FEEDBACK Chapter Outline 9.1 The General Feedback Structure 9.2 Some Properties of Negative Feedback 9.3 The Four Basic Feedback Topologies 9.4 The Feedback Voltage Amplifier (Series-Shunt) 9.5
More informationChapter 10 Feedback ECE 3120 Microelectronics II Dr. Suketu Naik
1 Chapter 10 Feedback Operational Amplifier Circuit Components 2 1. Ch 7: Current Mirrors and Biasing 2. Ch 9: Frequency Response 3. Ch 8: Active-Loaded Differential Pair 4. Ch 10: Feedback 5. Ch 11: Output
More informationTesting Power Sources for Stability
Keywords Venable, frequency response analyzer, oscillator, power source, stability testing, feedback loop, error amplifier compensation, impedance, output voltage, transfer function, gain crossover, bode
More informationOperational Amplifiers
Operational Amplifiers Table of contents 1. Design 1.1. The Differential Amplifier 1.2. Level Shifter 1.3. Power Amplifier 2. Characteristics 3. The Opamp without NFB 4. Linear Amplifiers 4.1. The Non-Inverting
More informationOscillators. Hartley, Colpitts, UJT relaxation. ECE/MEA Engg College S.R.K. 9/13/2007 Authored by: Ramesh.K
Oscillators Hartley, Colpitts, UJT relaxation. S.R.K 9//007 Authored by: Ramesh.K This documents contains a brief note about the principle of sinusoidal oscillator and some general oscillator circuits
More informationPositive Feedback and Oscillators
Physics 3330 Experiment #5 Fall 2011 Positive Feedback and Oscillators Purpose In this experiment we will study how spontaneous oscillations may be caused by positive feedback. You will construct an active
More informationBode and Log Magnitude Plots
Bode and Log Magnitude Plots Bode Magnitude and Phase Plots System Gain and Phase Margins & Bandwidths Polar Plot and Bode Diagrams Transfer Function from Bode Plots Bode Plots of Open Loop and Closed
More informationElectric Circuit Theory
Electric Circuit Theory Nam Ki Min nkmin@korea.ac.kr 010-9419-2320 Chapter 15 Active Filter Circuits Nam Ki Min nkmin@korea.ac.kr 010-9419-2320 Contents and Objectives 3 Chapter Contents 15.1 First-Order
More informationLecture 48 Review of Feedback HW # 4 Erickson Problems Ch. 9 # s 7 &9 and questions in lectures I. Review of Negative Feedback
Lecture 48 Review of Feedback HW # 4 Erickson Problems Ch. 9 # s 7 &9 and questions in lectures I. Review of Negative Feedback A. General. Overview 2. Summary of Advantages 3. Disadvantages B. Buck Converter
More informationEE 435. Lecture 16. Compensation Systematic Two-Stage Op Amp Design
EE 435 Lecture 16 Compensation Systematic Two-Stage Op Amp Design Review from last lecture Review of Basic Concepts Pole Locations and Stability Theorem: A system is stable iff all closed-loop poles lie
More informationFREQUENCY RESPONSE AND PASSIVE FILTERS LABORATORY
FREQUENCY RESPONSE AND PASSIVE FILTERS LABORATORY In this experiment we will analytically determine and measure the frequency response of networks containing resistors, AC source/sources, and energy storage
More informationMicroelectronic Circuits - Fifth Edition Sedra/Smith Copyright 2004 by Oxford University Press, Inc.
Feedback 1 Figure 8.1 General structure of the feedback amplifier. This is a signal-flow diagram, and the quantities x represent either voltage or current signals. 2 Figure E8.1 3 Figure 8.2 Illustrating
More informationHomework Assignment 13
Question 1 Short Takes 2 points each. Homework Assignment 13 1. Classify the type of feedback uses in the circuit below (i.e., shunt-shunt, series-shunt, ) Answer: Series-shunt. 2. True or false: an engineer
More informationHomework Assignment 10
Homework Assignment 10 Question The amplifier below has infinite input resistance, zero output resistance and an openloop gain. If, find the value of the feedback factor as well as so that the closed-loop
More informationPURPOSE: NOTE: Be sure to record ALL results in your laboratory notebook.
EE4902 Lab 9 CMOS OP-AMP PURPOSE: The purpose of this lab is to measure the closed-loop performance of an op-amp designed from individual MOSFETs. This op-amp, shown in Fig. 9-1, combines all of the major
More informationEES42042 Fundamental of Control Systems Bode Plots
EES42042 Fundamental of Control Systems Bode Plots DR. Ir. Wahidin Wahab M.Sc. Ir. Aries Subiantoro M.Sc. 2 Bode Plots Plot of db Gain and phase vs frequency It is assumed you know how to construct Bode
More informationEECE488: Analog CMOS Integrated Circuit Design Set 7 Opamp Design
EECE488: Analog CMOS Integrated Circuit Design Set 7 Opamp Design References: Analog Integrated Circuit Design by D. Johns and K. Martin and Design of Analog CMOS Integrated Circuits by B. Razavi All figures
More information1.What is frequency response? A frequency responses the steady state response of a system when the input to the system is a sinusoidal signal.
Control Systems (EC 334) 1.What is frequency response? A frequency responses the steady state response of a system when the input to the system is a sinusoidal signal. 2.List out the different frequency
More informationPoles and Zeros of H(s), Analog Computers and Active Filters
Poles and Zeros of H(s), Analog Computers and Active Filters Physics116A, Draft10/28/09 D. Pellett LRC Filter Poles and Zeros Pole structure same for all three functions (two poles) HR has two poles and
More informationBSNL TTA Question Paper Control Systems Specialization 2007
BSNL TTA Question Paper Control Systems Specialization 2007 1. An open loop control system has its (a) control action independent of the output or desired quantity (b) controlling action, depending upon
More informationSECTION 7: FREQUENCY DOMAIN ANALYSIS. MAE 3401 Modeling and Simulation
SECTION 7: FREQUENCY DOMAIN ANALYSIS MAE 3401 Modeling and Simulation 2 Response to Sinusoidal Inputs Frequency Domain Analysis Introduction 3 We ve looked at system impulse and step responses Also interested
More informationNH 67, Karur Trichy Highways, Puliyur C.F, Karur District DEPARTMENT OF INFORMATION TECHNOLOGY DIGITAL SIGNAL PROCESSING UNIT 3
NH 67, Karur Trichy Highways, Puliyur C.F, 639 114 Karur District DEPARTMENT OF INFORMATION TECHNOLOGY DIGITAL SIGNAL PROCESSING UNIT 3 IIR FILTER DESIGN Structure of IIR System design of Discrete time
More informationDr Ian R. Manchester
Week Content Notes 1 Introduction 2 Frequency Domain Modelling 3 Transient Performance and the s-plane 4 Block Diagrams 5 Feedback System Characteristics Assign 1 Due 6 Root Locus 7 Root Locus 2 Assign
More informationActive Filter Design Techniques
Active Filter Design Techniques 16.1 Introduction What is a filter? A filter is a device that passes electric signals at certain frequencies or frequency ranges while preventing the passage of others.
More informationTesting and Stabilizing Feedback Loops in Today s Power Supplies
Keywords Venable, frequency response analyzer, impedance, injection transformer, oscillator, feedback loop, Bode Plot, power supply design, open loop transfer function, voltage loop gain, error amplifier,
More informationELC224 Final Review (12/10/2009) Name:
ELC224 Final Review (12/10/2009) Name: Select the correct answer to the problems 1 through 20. 1. A common-emitter amplifier that uses direct coupling is an example of a dc amplifier. 2. The frequency
More informationPhysics 132 Quiz # 23
Name (please (please print) print) Physics 132 Quiz # 23 I. I. The The current in in an an ac ac circuit is is represented by by a phasor.the value of of the the current at at some time time t t is is
More informationHomework Assignment 13
Question 1 Short Takes 2 points each. Homework Assignment 13 1. Classify the type of feedback uses in the circuit below (i.e., shunt-shunt, series-shunt, ) 2. True or false: an engineer uses series-shunt
More informationDesign and comparison of butterworth and chebyshev type-1 low pass filter using Matlab
Research Cell: An International Journal of Engineering Sciences ISSN: 2229-6913 Issue Sept 2011, Vol. 4 423 Design and comparison of butterworth and chebyshev type-1 low pass filter using Matlab Tushar
More informationLecture 18 Stability of Feedback Control Systems
16.002 Lecture 18 Stability of Feedback Control Systems May 9, 2008 Today s Topics Stabilizing an unstable system Stability evaluation using frequency responses Take Away Feedback systems stability can
More informationFriday, 1/27/17 Constraints on A(jω)
Friday, 1/27/17 Constraints on A(jω) The simplest electronic oscillators are op amp based, and A(jω) is typically a simple op amp fixed gain amplifier, such as the negative gain and positive gain amplifiers
More informationOperational Amplifier BME 360 Lecture Notes Ying Sun
Operational Amplifier BME 360 Lecture Notes Ying Sun Characteristics of Op-Amp An operational amplifier (op-amp) is an analog integrated circuit that consists of several stages of transistor amplification
More informationOscillator Principles
Oscillators Introduction Oscillators are circuits that generates a repetitive waveform of fixed amplitude and frequency without any external input signal. The function of an oscillator is to generate alternating
More informationChapter 13 Oscillators and Data Converters
Chapter 13 Oscillators and Data Converters 13.1 General Considerations 13.2 Ring Oscillators 13.3 LC Oscillators 13.4 Phase Shift Oscillator 13.5 Wien-Bridge Oscillator 13.6 Crystal Oscillators 13.7 Chapter
More informationLaboratory 4 Operational Amplifier Department of Mechanical and Aerospace Engineering University of California, San Diego MAE170
Laboratory 4 Operational Amplifier Department of Mechanical and Aerospace Engineering University of California, San Diego MAE170 Megan Ong Diana Wu Wong B01 Tuesday 11am April 28 st, 2015 Abstract: The
More informationCHAPTER 11. Feedback. Microelectronic Circuits, Seventh Edition. Copyright 2015 by Oxford University Press
CHAPTER 11 Feedback Figure 11.1 General structure of the feedback amplifier. This is a signal-flow diagram, and the quantities x represent either voltage or current signals. Figure 11.2 Determining the
More informationANNA UNIVERSITY :: CHENNAI MODEL QUESTION PAPER(V-SEMESTER) B.E. ELECTRONICS AND COMMUNICATION ENGINEERING EC334 - CONTROL SYSTEMS
ANNA UNIVERSITY :: CHENNAI - 600 025 MODEL QUESTION PAPER(V-SEMESTER) B.E. ELECTRONICS AND COMMUNICATION ENGINEERING EC334 - CONTROL SYSTEMS Time: 3hrs Max Marks: 100 Answer all Questions PART - A (10
More informationIntroduction to Signals and Systems Lecture #9 - Frequency Response. Guillaume Drion Academic year
Introduction to Signals and Systems Lecture #9 - Frequency Response Guillaume Drion Academic year 2017-2018 1 Transmission of complex exponentials through LTI systems Continuous case: LTI system where
More informationAssist Lecturer: Marwa Maki. Active Filters
Active Filters In past lecture we noticed that the main disadvantage of Passive Filters is that the amplitude of the output signals is less than that of the input signals, i.e., the gain is never greater
More informationVälkomna till TSRT15 Reglerteknik Föreläsning 5. Summary of lecture 4 Frequency response Bode plot
Välkomna till TSRT15 Reglerteknik Föreläsning 5 Summary of lecture 4 Frequency response Bode plot Summary of last lecture 2 Given a pole polynomial with a varying parameter P(s)+KQ(s)=0 We draw the location
More informationJUNE 2014 Solved Question Paper
JUNE 2014 Solved Question Paper 1 a: Explain with examples open loop and closed loop control systems. List merits and demerits of both. Jun. 2014, 10 Marks Open & Closed Loop System - Advantages & Disadvantages
More informationUNIVERSITY OF NORTH CAROLINA AT CHARLOTTE Department of Electrical and Computer Engineering
UNIVERSITY OF NORTH CAROLINA AT CHARLOTTE Department of Electrical and Computer Engineering EXPERIMENT 5 GAIN-BANDWIDTH PRODUCT AND SLEW RATE OBJECTIVES In this experiment the student will explore two
More informationBJT & FET Frequency Response
Chapter 4 BJT & FET Spring 2012 4 th Semester Mechatronics SZABIST, Karachi 2 Course Support humera.rafique@szabist.edu.pk Office: 100 Campus (404) Official: ZABdesk Subsidiary: https://sites.google.com/site/zabistmechatronics/home/spring-2012/ecd
More informationHomework Assignment 11
Homework Assignment 11 Question 1 (Short Takes) Two points each unless otherwise indicated. 1. What is the 3-dB bandwidth of the amplifier shown below if r π = 2.5K, r o = 100K, g m = 40 ms, and C L =
More informationAnalog Circuits Prof. Jayanta Mukherjee Department of Electrical Engineering Indian Institute of Technology-Bombay
Analog Circuits Prof. Jayanta Mukherjee Department of Electrical Engineering Indian Institute of Technology-Bombay Week -02 Module -01 Non Idealities in Op-Amp (Finite Gain, Finite Bandwidth and Slew Rate)
More informationEK307 Active Filters and Steady State Frequency Response
EK307 Active Filters and Steady State Frequency Response Laboratory Goal: To explore the properties of active signal-processing filters Learning Objectives: Active Filters, Op-Amp Filters, Bode plots Suggested
More informationEE Experiment 8 Bode Plots of Frequency Response
EE16:Exp8-1 EE 16 - Experiment 8 Bode Plots of Frequency Response Objectives: To illustrate the relationship between a system frequency response and the frequency response break frequencies, factor powers,
More informationECE4902 C Lab 5 MOSFET Common Source Amplifier with Active Load Bandwidth of MOSFET Common Source Amplifier: Resistive Load / Active Load
ECE4902 C2012 - Lab 5 MOSFET Common Source Amplifier with Active Load Bandwidth of MOSFET Common Source Amplifier: Resistive Load / Active Load PURPOSE: The primary purpose of this lab is to measure the
More informationElectronics basics for MEMS and Microsensors course
Electronics basics for course, a.a. 2017/2018, M.Sc. in Electronics Engineering Transfer function 2 X(s) T(s) Y(s) T S = Y s X(s) The transfer function of a linear time-invariant (LTI) system is the function
More informationFrequency Response Analysis and Design Tutorial
1 of 13 1/11/2011 5:43 PM Frequency Response Analysis and Design Tutorial I. Bode plots [ Gain and phase margin Bandwidth frequency Closed loop response ] II. The Nyquist diagram [ Closed loop stability
More informationOperational Amplifiers
Operational Amplifiers Continuing the discussion of Op Amps, the next step is filters. There are many different types of filters, including low pass, high pass and band pass. We will discuss each of the
More informationKent Bertilsson Muhammad Amir Yousaf
Today s topics Analog System (Rev) Frequency Domain Signals in Frequency domain Frequency analysis of signals and systems Transfer Function Basic elements: R, C, L Filters RC Filters jw method (Complex
More informationECE4902 Lab 5 Simulation. Simulation. Export data for use in other software tools (e.g. MATLAB or excel) to compare measured data with simulation
ECE4902 Lab 5 Simulation Simulation Export data for use in other software tools (e.g. MATLAB or excel) to compare measured data with simulation Be sure to have your lab data available from Lab 5, Common
More informationDesign of a Regenerative Receiver for the Short-Wave Bands A Tutorial and Design Guide for Experimental Work. Part I
Design of a Regenerative Receiver for the Short-Wave Bands A Tutorial and Design Guide for Experimental Work Part I Ramón Vargas Patrón rvargas@inictel-uni.edu.pe INICTEL-UNI Regenerative Receivers remain
More informationClass #16: Experiment Matlab and Data Analysis
Class #16: Experiment Matlab and Data Analysis Purpose: The objective of this experiment is to add to our Matlab skill set so that data can be easily plotted and analyzed with simple tools. Background:
More informationECE 3155 Experiment I AC Circuits and Bode Plots Rev. lpt jan 2013
Signature Name (print, please) Lab section # Lab partner s name (if any) Date(s) lab was performed ECE 3155 Experiment I AC Circuits and Bode Plots Rev. lpt jan 2013 In this lab we will demonstrate basic
More informationECE 363 FINAL (F16) 6 problems for 100 pts Problem #1: Fuel Pump Controller (18 pts)
ECE 363 FINAL (F16) NAME: 6 problems for 100 pts Problem #1: Fuel Pump Controller (18 pts) You are asked to design a high-side switch for a remotely operated fuel pump. You decide to use the IRF9520 power
More informationHomework Assignment 06
Question 1 (2 points each unless noted otherwise) Homework Assignment 06 1. True or false: when transforming a circuit s diagram to a diagram of its small-signal model, we replace dc constant current sources
More informationMotor Control. Suppose we wish to use a microprocessor to control a motor - (or to control the load attached to the motor!) Power supply.
Motor Control Suppose we wish to use a microprocessor to control a motor - (or to control the load attached to the motor!) Operator Input CPU digital? D/A, PWM analog voltage Power supply Amplifier linear,
More informationFEEDBACK AMPLIFIER. Learning Objectives. A feedback amplifier is one in which a fraction of the amplifier output is fed back to the input circuit
C H P T E R6 Learning Objectives es Feedback mplifiers Principle of Feedback mplifiers dvantages of Negative Feedback Gain Stability Decreased Distortion Feedback Over Several Stages Increased Bandwidth
More informationReview of Filter Types
ECE 440 FILTERS Review of Filters Filters are systems with amplitude and phase response that depends on frequency. Filters named by amplitude attenuation with relation to a transition or cutoff frequency.
More informationHomework Assignment 03 Solution
Homework Assignment 03 Solution Question 1 Determine the h 11 and h 21 parameters for the circuit. Be sure to supply the units and proper sign for each parameter. (8 points) Solution Setting v 2 = 0 h
More informationCHAPTER 6 Frequency Response, Bode. Plots, and Resonance
CHAPTER 6 Frequency Response, Bode Plots, and Resonance CHAPTER 6 Frequency Response, Bode Plots, and Resonance 1. State the fundamental concepts of Fourier analysis. 2. Determine the output of a filter
More informationNew Techniques for Testing Power Factor Correction Circuits
Keywords Venable, frequency response analyzer, impedance, injection transformer, oscillator, feedback loop, Bode Plot, power supply design, power factor correction circuits, current mode control, gain
More informationLecture 8: More on Operational Amplifiers (Op Amps)
Lecture 8: More on Operational mplifiers (Op mps) Input Impedance of Op mps and Op mps Using Negative Feedback: Consider a general feedback circuit as shown. ssume that the amplifier has input impedance
More informationExperiment 1: Amplifier Characterization Spring 2019
Experiment 1: Amplifier Characterization Spring 2019 Objective: The objective of this experiment is to develop methods for characterizing key properties of operational amplifiers Note: We will be using
More informationFoundations of Oscillator Circuit Design
Foundations of Oscillator Circuit Design For a listing of recent titles in the Artech House Microwave Library, turn to the back of this book. Foundations of Oscillator Circuit Design Guillermo Gonzalez
More informationLab 9: Operational amplifiers II (version 1.5)
Lab 9: Operational amplifiers II (version 1.5) WARNING: Use electrical test equipment with care! Always double-check connections before applying power. Look for short circuits, which can quickly destroy
More informationAndrea Zanchettin Automatic Control 1 AUTOMATIC CONTROL. Andrea M. Zanchettin, PhD Winter Semester, Linear control systems design Part 1
Andrea Zanchettin Automatic Control 1 AUTOMATIC CONTROL Andrea M. Zanchettin, PhD Winter Semester, 2018 Linear control systems design Part 1 Andrea Zanchettin Automatic Control 2 Step responses Assume
More informationTHE K FACTOR: A NEW MATHEMATICAL TOOL FOR STABILITY ANALYSIS AND SYNTHESIS
Reference Reading #4 THE K FACTOR: A NEW MATHEMATICAL TOOL FOR STABILITY ANALYSIS AND SYNTHESIS H. Dean Venable Venable Industries, Inc. 2120 W. Braker Lane, Suite M Austin, TX 78758 info@venableind.com
More informationLecture 16 Date: Frequency Response (Contd.)
Lecture 16 Date: 03.10.2017 Frequency Response (Contd.) Bode Plot (contd.) Bode Plot (contd.) Bode Plot (contd.) not every transfer function has all seven factors. To sketch the Bode plots for a generic
More informationTest Your Understanding
074 Part 2 Analog Electronics EXEISE POBLEM Ex 5.3: For the switched-capacitor circuit in Figure 5.3b), the parameters are: = 30 pf, 2 = 5pF, and F = 2 pf. The clock frequency is 00 khz. Determine the
More informationLaboratory PID Tuning Based On Frequency Response Analysis. 2. be able to evaluate system performance for empirical tuning method;
Laboratory PID Tuning Based On Frequency Response Analysis Objectives: At the end, student should 1. appreciate a systematic way of tuning PID loop by the use of process frequency response analysis; 2.
More informationEE 482 : CONTROL SYSTEMS Lab Manual
University of Bahrain College of Engineering Dept. of Electrical and Electronics Engineering EE 482 : CONTROL SYSTEMS Lab Manual Dr. Ebrahim Al-Gallaf Assistance Professor of Intelligent Control and Robotics
More informationLecture 17 z-transforms 2
Lecture 17 z-transforms 2 Fundamentals of Digital Signal Processing Spring, 2012 Wei-Ta Chu 2012/5/3 1 Factoring z-polynomials We can also factor z-transform polynomials to break down a large system into
More informationFinal Exam. 1. An engineer measures the (step response) rise time of an amplifier as t r = 0.1 μs. Estimate the 3 db bandwidth of the amplifier.
Final Exam Name: Score /100 Question 1 Short Takes 1 point each unless noted otherwise. 1. An engineer measures the (step response) rise time of an amplifier as t r = 0.1 μs. Estimate the 3 db bandwidth
More informationEEL2216 Control Theory CT2: Frequency Response Analysis
EEL2216 Control Theory CT2: Frequency Response Analysis 1. Objectives (i) To analyse the frequency response of a system using Bode plot. (ii) To design a suitable controller to meet frequency domain and
More informationThursday, 1/23/19 Automatic Gain Control As previously shown, 1 0 is a nonlinear system that produces a limit cycle with a distorted sinusoid for
Thursday, 1/23/19 Automatic Gain Control As previously shown, 1 0 is a nonlinear system that produces a limit cycle with a distorted sinusoid for x(t), which is not a very good sinusoidal oscillator. A
More informationLow Pass Filter Introduction
Low Pass Filter Introduction Basically, an electrical filter is a circuit that can be designed to modify, reshape or reject all unwanted frequencies of an electrical signal and accept or pass only those
More informationEE 210 Lab Exercise #5: OP-AMPS I
EE 210 Lab Exercise #5: OP-AMPS I ITEMS REQUIRED EE210 crate, DMM, EE210 parts kit, T-connector, 50Ω terminator, Breadboard Lab report due at the ASSIGNMENT beginning of the next lab period Data and results
More informationECE 231 Laboratory Exercise 6 Frequency / Time Response of RL and RC Circuits
ECE 231 Laboratory Exercise 6 Frequency / Time Response of RL and RC Circuits Laboratory Group (Names) OBJECTIVES Observe and calculate the response of first-order low pass and high pass filters. Gain
More informationGlossary of VCO terms
Glossary of VCO terms VOLTAGE CONTROLLED OSCILLATOR (VCO): This is an oscillator designed so the output frequency can be changed by applying a voltage to its control port or tuning port. FREQUENCY TUNING
More informationDESIGN AND ANALYSIS OF FEEDBACK CONTROLLERS FOR A DC BUCK-BOOST CONVERTER
DESIGN AND ANALYSIS OF FEEDBACK CONTROLLERS FOR A DC BUCK-BOOST CONVERTER Murdoch University: The Murdoch School of Engineering & Information Technology Author: Jason Chan Supervisors: Martina Calais &
More informationDifference between BJTs and FETs. Junction Field Effect Transistors (JFET)
Difference between BJTs and FETs Transistors can be categorized according to their structure, and two of the more commonly known transistor structures, are the BJT and FET. The comparison between BJTs
More informationComparison of Signal Attenuation of Multiple Frequencies Between Passive and Active High-Pass Filters
Comparison of Signal Attenuation of Multiple Frequencies Between Passive and Active High-Pass Filters Aaron Batker Pritzker Harvey Mudd College 23 November 203 Abstract Differences in behavior at different
More informationEE233 Autumn 2016 Electrical Engineering University of Washington. EE233 HW7 Solution. Nov. 16 th. Due Date: Nov. 23 rd
EE233 HW7 Solution Nov. 16 th Due Date: Nov. 23 rd 1. Use a 500nF capacitor to design a low pass passive filter with a cutoff frequency of 50 krad/s. (a) Specify the cutoff frequency in hertz. fc c 50000
More informationSAR (successive-approximation-register) ADCs
By Miro Oljaca and Bonnie C Baker Texas Instruments Start with the right op amp when driving SAR ADCs Using the right operational amplifier in front of your data converter will give you good performance.
More informationExercise 4: (More) Filters
Exercise 4: (More) Filters Prof. Dr. P. Fischer Lehrstuhl für Schaltungstechnik und Simulation Uni Heidelberg CCS Exercise 4: Filters P. Fischer, ZITI, Uni Heidelberg Page1 Exercise 4.1 Analyze the following
More informationCDS 101/110a: Lecture 8-1 Frequency Domain Design
CDS 11/11a: Lecture 8-1 Frequency Domain Design Richard M. Murray 17 November 28 Goals: Describe canonical control design problem and standard performance measures Show how to use loop shaping to achieve
More informationLecture # 11 Oscillators (RC Circuits)
December 2014 Benha University Faculty of Engineering at Shoubra ECE-312 Electronic Circuits (A) Lecture # 11 Oscillators (RC Circuits) Instructor: Dr. Ahmad El-Banna Agenda Introduction Feedback Oscillators
More informationModeling and Analysis of Systems Lecture #9 - Frequency Response. Guillaume Drion Academic year
Modeling and Analysis of Systems Lecture #9 - Frequency Response Guillaume Drion Academic year 2015-2016 1 Outline Frequency response of LTI systems Bode plots Bandwidth and time-constant 1st order and
More informationElectrical Engineering. Control Systems. Comprehensive Theory with Solved Examples and Practice Questions. Publications
Electrical Engineering Control Systems Comprehensive Theory with Solved Examples and Practice Questions Publications Publications MADE EASY Publications Corporate Office: 44-A/4, Kalu Sarai (Near Hauz
More informationTheory: The idea of this oscillator comes from the idea of positive feedback, which is described by Figure 6.1. Figure 6.1: Positive Feedback
Name1 Name2 12/2/10 ESE 319 Lab 6: Colpitts Oscillator Introduction: This lab introduced the concept of feedback in combination with bipolar junction transistors. The goal of this lab was to first create
More informationOperational Amplifier
Operational Amplifier Joshua Webster Partners: Billy Day & Josh Kendrick PHY 3802L 10/16/2013 Abstract: The purpose of this lab is to provide insight about operational amplifiers and to understand the
More informationETIN25 Analogue IC Design. Laboratory Manual Lab 2
Department of Electrical and Information Technology LTH ETIN25 Analogue IC Design Laboratory Manual Lab 2 Jonas Lindstrand Martin Liliebladh Markus Törmänen September 2011 Laboratory 2: Design and Simulation
More information(1) Identify individual entries in a Control Loop Diagram. (2) Sketch Bode Plots by hand (when we could have used a computer
Last day: (1) Identify individual entries in a Control Loop Diagram (2) Sketch Bode Plots by hand (when we could have used a computer program to generate sketches). How might this be useful? Can more clearly
More information