Glasgow eprints Service
|
|
- Stuart Ross Cain
- 6 years ago
- Views:
Transcription
1 Gallegos-Lopez, G. and Kjaer, P.C. and Miller, T.J.E. (1998) A new sensorless method for switched reluctance motor drives. IEEE Transactions on Industry Applications 34(4):pp Glasgow eprints Service
2 832 IEEE TRANSACTIONS ON INDUSTRY APPLICATIONS, VOL. 34, NO. 4, JULY/AUGUST 1998 A New Sensorless Method for Switched Reluctance Motor Drives Gabriel Gallegos-López, Student Member, IEEE, Philip C. Kjaer, Member, IEEE, and Timothy J. E. Miller, Fellow, IEEE Abstract This paper describes a new method for indirect sensing of the rotor position in switched reluctance motors (SRM s) using pulsewidth modulation voltage control. The detection method uses the change of the derivative of the phase current to detect the position where a rotor pole and stator pole start to overlap, giving one position update per energy conversion. As no a priori knowledge of motor parameters is required (except for the numbers of stator and rotor poles), the method is applicable to most SRM topologies in a wide power and speed range and for several inverter topologies. The method allows modest closed-loop dynamic performance. To start up the motor, a feedforward stepping method is used which assures robust startup (even under load) from standstill to a predefined speed at which closed-loop sensorless operation can be applied. Experimental results demonstrate the robust functionality of the method with just one current sensor in the inverter, even with excitation overlap, and the sensorless operation improves with speed. The method is comparable to the back-emf position estimation for brushless dc motors in principle, performance, and cost. A detailed operation and implementation of this scheme is shown, together with steady-state and dynamic transient test results. Index Terms Adjustable-speed drives, sensorless control, switched reluctance motors. Fig. 1. 6/4 three-phase SRM. TABLE I MOTOR RATINGS I. INTRODUCTION IN RECENT YEARS, the switched reluctance motor (SRM) has received considerable attention for variable-speed drive applications. Its simple construction, due to the absence of magnets, rotor conductors, and brushes, and high system efficiency over a wide speed range make the SRM drive an interesting alternative to compete with permanent magnet (PM) brushless dc motor and induction motor drives. However, the need for a direct rotor position sensor to commutate the current from phase to phase synchronously with rotor position has excluded the motor from many cost-sensitive applications. Fig. 1 shows a 6/4 three-phase SRM. An encoder, resolver, or Hall sensor attached to the shaft is normally used to supply the rotor position, but the use of these Paper IPCSD 98 22, presented at the 1997 Industry Applications Society Annual Meeting, New Orleans, LA, October 5 9, and approved for publication in the IEEE TRANSACTIONS ON INDUSTRY APPLICATIONS by the Industrial Drives Committee of the IEEE Industry Applications Society. The work of G. Gallegos-López was supported by Consejo Nacional de Ciencia y Tecnología México (CONACyT). Manuscript released for publication March 11, G. Gallegos-López and T. J. E. Miller are with the SPEED Laboratory, Department of Electronics and Electrical Engineering, University of Glasgow, Glasgow G12 8LT, Scotland, U.K. P. C. Kjaer was with the SPEED Laboratory, Department of Electronics and Electrical Engineering, University of Glasgow, Glasgow G12 8LT, Scotland, U.K. He is now with ABB Corporate Research, Västerås, Sweden. Publisher Item Identifier S (98) sensors may lead to reliability problems in harsh environments or may become an important part of the overall drive system cost for drives below 1-hp. Also, they increase the overall physical envelope of the motor drive and the number of extra wires. In this paper, a new method for indirect sensing of the rotor position in SRM s using PWM voltage control is proposed. The paper is structured as follows: a brief review of indirect methods for position detection is given, followed by a theoretical examination of the proposed current gradient sensorless method (CGSM), the implementation of the method and experimental results, a detailed account of the startup /98$ IEEE
3 GALLEGOS-LÓPEZ et al.: A NEW SENSORLESS METHOD FOR SWITCHED RELUCTANCE MOTOR DRIVES 833 Fig. 2. Classic SRM inverter with lower rails divided showing current sensor placements. procedure, and conclusions. Table I shows the ratings of the motor used. A. Review All SRM s possess a unique relationship between phase inductance, phase current, and rotor position, which makes prediction of rotor position possible. Several indirect rotor position methods have been proposed in the literature, all making use of the inductance variation in one way or another. For example, the chopping current detection technique by Acarnley et al. [1], the flux-current detection technique by Lyons et al. [2] and Hedlund [3], the impedance sensing by Acarnley et al. [1] and MacMinn et al. [4], the modulation techniques by Ehsani et al. [5], [6], the mutually induced voltage by Husain [7], the resonant method by Laurent et al. [8], and the open-loop control by Bass et al. [9]. A more sophisticated method is the state observer presented by Lumsdaine [10], but it requires a powerful digital signal processor (DSP). Most of the proposed sensorless methods require some knowledge of the motor s magnetic characteristic. In this paper, a new and attractive CGSM, proposed originally by Kjær et al. [11], is for the first time implemented and analyzed. This particular low-cost method needs no a priori knowledge of the motor parameters, except the pole configuration, and it is, therefore, applicable to most SRM topologies. II. THEORY The SRM is usually controlled by either closed-loop current control or open-loop PWM voltage control. There are three types of current control. 1) Hysteresis current control The current is controlled between two current levels equal to where reference current and hysteresis band. The switching frequency is uncontrolled. 2) Delta modulation The current is regulated around with maximum switching frequency limited, also called bang-bang current control. 3) Current regulation with PWM The current is regulated close to using PWM. In voltage control, a fixed switching frequency is used to modulate the chopping transistor. The PWM duty cycle is constant during one electrical cycle, but it can be varied to Fig. 3. Typical current waveform in PWM voltage control. control the average phase voltage: where dc-link voltage and PWM duty cycle which is defined as the fraction of time that the switch is on with respect to the period of the switching frequency. The simplest way is to leave Q2, Q4, and Q6 on from to and chop Q1, Q3, and Q5 at fixed frequency with its corresponding duty cycle (Figs. 2 and 3). The main advantage of current control over voltage control is that the phase current can be controlled precisely, which means that reduction of torque ripple or noise is possible, however, it requires a current sensor for each phase. In contrast, voltage control typically requires only one current sensor in the dc link for overcurrent protection. From the aforementioned, voltage control is attractive for low-power/low-cost SRM drives, due to the reduced number of current sensors and signal processing required. The theory behind CGSM is based on voltage control, and it is explained as follows. The phase voltage can be expressed by where phase inductance, phase resistance, phase current, speed, and rotor position. Now, let be defined as the rotor position at which a rotor pole and a stator pole begin to overlap (i.e., where the phase inductance begins to increase), and consider two situations, one just before reaching, referred to as, and other just after passing, referred to as. The voltage equations for these two situations, neglecting the voltage drop in the phase (1) (2)
4 834 IEEE TRANSACTIONS ON INDUSTRY APPLICATIONS, VOL. 34, NO. 4, JULY/AUGUST 1998 resistance, become (3) (4) The inductance at rotor position is ideally equal to the inductance at the unaligned rotor position (see Fig. 3): which yields Therefore, the voltage equations for the two rotor positions can be rewritten as, the voltage is main- A. CGSM As the phase is turned on before tained constant in a stroke 1 : By manipulation of (7) (9), we obtain (5) (6) (7) (8) (9) (10) As the right-hand side of (10) is positive, the following inequality is always true: The slope of the phase current is always larger for than for (11) This is the core principle of the CGSM. Fig. 3 shows a typical current waveform for PWM voltage control. It is clear that, when the phase inductance starts to increase at must decrease, or even become zero. 1) CGSM for Switched Reluctance Generator: Let us define as the rotor position at which the rotor and stator poles seize to overlap. For generating, the phase is usually turned on before the aligned position and turned off after, but before (Fig. 4). Assuming that the phase voltage is maintained constant while the current freewheels through the diodes, i.e.,, we obtain 1 One energy conversion in a single phase. (12) Fig. 4. Typical generated phase current. As the right-hand side of (12) is always negative, the following inequality is always true: The slope of the generated phase current is always larger for than for (13) Fig. 4 shows a typical generated current waveform. It is clear that, when the phase inductance reaches its minimum value at must decrease. From the aforementioned, we can say that an accurate indication of the rotor position can be detected for both motoring and generating, simply by detection of the change in (assuming constant speed). The CGSM senses, which is given by the motor geometry. One rotor position is estimated per stroke, where the stroke angle in mechanical degrees is defined as (14) where and are the number of rotor poles and the number of phases, respectively. 2) Advantages of CGSM: The most important advantages of the method are the following. Noa priori knowledge of inductance profile is required. It is applicable to any regular SRM. 2 No prestored data of magnetization curves are needed. It is applicable in four-quadrant operation of the drive. It does not compromise the performance of the motor. It allows closed-loop speed control by changing the duty cycle, commutation angles, or both. The commutation angles can be set freely with the condition of (for motoring). Implementation is simple, with a minimum of extra components. Either the lower transistor bus current waveform or the currents sensed in each phase are used as feedback. allows operation with only one current sensor. No extra computation, control requirements, or compensation factors are needed. It allows excitation overlap. It is suitable for medium and high speed, given that the peak in the current waveform becomes more prominent with increased speed. 2 A regular switched reluctance motor is one in which the rotor and stator poles are symmetrical about their centrelines and equally spaced around the rotor and stator respectively. [13]
5 GALLEGOS-LÓPEZ et al.: A NEW SENSORLESS METHOD FOR SWITCHED RELUCTANCE MOTOR DRIVES 835 Fig. 5. Detection stage. 3) Disadvantages of CGSM: On the other hand, the disadvantages are as follows. It is not applicable at standstill. It needs a startup procedure. It is not suitable for low speed. It does not allow large load torque transients. Current regulation is not allowed for reduction of torque ripple or noise. It does not have very good efficiency at low speed and low torque. Fig. 6. Block diagram of sensorless SRM drive. III. IMPLEMENTATION The CGSM has been implemented and analyzed for motoring. It is comparable to the back-emf zero-crossing method of position estimation for brushless dc motors [12]. In a threephase brushless dc machine, the zero crossing of the back EMF indicates two positions per phase per cycle, while the method presented here, according to (11), indicates one position per phase per cycle and, from these pulses, commutation angles can be obtained. Both motors need a startup procedure (feedforward) when operated without a position sensor. The block diagram for the fully analog electronic detection circuit is shown in Fig. 5. It is comprised of a current sensor, two low-pass filters, a differentiator, and a zero-crossing detector. The low-pass filters are used to eliminate the switching frequency and possible noise. For each low-pass filter, a second-order Butterworth filter was used, where the cutoff frequency is determined by the PWM switching frequency. In this case, a cutoff frequency of 8 khz was used for a switching frequency of 16 khz. The differentiator is used to obtain, and the zero-crossing detector gives a pulse when is zero. For simplicity, is detected, which puts constraints on the current waveform that should have at least one peak. However, a detection stage that detects the change in, rather than, could be implemented. If the drive is going to be operated in single-pulse mode (i.e., ) the low-pass filters are not necessary, and the number of components in the detection stage is reduced significantly. It should be noted that the electronic circuitry required for the CGSM is minimal (operational amplifiers, resistors, and capacitors), with obvious scope for implementation as a singlechip solution. Fig. 6 shows the block diagram of the sensorless SRM drive. The sensorless position estimation pulses can be generated either by each phase current or the current in the lower transistor bus (, see Fig. 2), which contains the same information as the phase currents required for motoring Fig. 7. Block diagram of phase-locked loop (PLL) position interpolation. operation. A single pulse train containing all the required information is obtained from either a single detection circuit sensing or the combination of (OR-gate) sensorless pulses from each phase. Another option that uses only one detection circuit is to multiplex all phase currents. The commutation stage is implemented with a fieldprogrammable gate array (FPGA) (Xilinx XC3195A) for flexibility in the development stage, but it could be realized with simple, low-cost digital, or even analog, components. The sensorless pulses are used to generate a position counter as follows. The train of sensorless pulses spaced 30 [according to (14)], obtained from the detection circuit, is used to generate a pulse train with 32 pulses per 30. In other words, the frequency of the sensorless pulses is multiplied by 32 (using a PLL). Fig. 7 shows the block diagram of the implemented logic circuitry. There are two counters, counter I running at frequency and counter II running at frequency. Upon the arrival of a sensorless pulse, the value of counter I is first held in a register, and then, the counter is reset. The value of counter II builds up to the value in the register. When its value equals the register s value, the comparator generates a pulse and resets counter II. So, a resolution of 384 pulses per revolution is obtained, which is enough to generate commutation pulses with adequate resolution. A microcontroller (Motorola MC68332) is used to close the speed loop and to analyze this sensorless scheme (less
6 836 IEEE TRANSACTIONS ON INDUSTRY APPLICATIONS, VOL. 34, NO. 4, JULY/AUGUST 1998 Fig. 8. Hardware overview. powerful microcontrollers could be used). A classic inverter topology with two transistors and two diodes per phase is used with the variation of splitting the lower rail into two buses, the lower diode bus and the lower transistor bus (Fig. 2), so that the current in the commutating transistors can be observed by. The experiments have been carried out with both one single detection circuit and one detection circuit per phase. It was found that using does not compromise the drive s performance in any way. A proportional integral (PI) closed-loop speed controller, which varies the PWM duty cycle for load compensation (as indicated in Fig. 6), has been implemented. The firing angles are programmable and can be varied easily to control the motor torque, but they remained fixed in the dynamic tests conducted here. The only operating constraint is to assure, which is not an onerous restriction at any operating speed or torque. IV. EXPERIMENTAL RESULTS A fractional horsepower 6/4 three-phase SRM was used to investigate the performance and limitations of the new method. The test motor and the load machine were coupled with flexible rubber couplings. The load machine was a PM motor connected in series with a resistance and a current-controlled power supply. The complete setup is shown in Fig. 8. The experiments include detection of sensorless pulses, accuracy in rotor position estimation, speed transients, torque transients, and the assessment of torque-speed range where the motor can be operated sensorless. The angles are represented in mechanical degrees. Fig. 9 shows one phase current, lower transistor bus current, the current gradient position estimation (CGPE) pulses obtained from, and the decoded pulses (DP) for phase 1 measured at 1763 r/min with. Clearly, the correct rotor position is detected. Fig. 9 illustrates the case of excitation overlap, showing, CGPE, and DP for phase 1 measured at 1820 r/min, with. Note that this time, two sensorless pulses appear per stroke; the first one is erroneous (when the previous phase is turned off), and the second one gives. A simple logic circuit neglects the first pulse when there is excitation overlap, so DP becomes the decoded signal for phase 1. Fig. 10 depicts the estimated position and the position given by the 1024-line encoder in steady state Fig. 9. Single-pulse current waveforms. on = 50 ; o =80 (no excitation overlap). on =50 ; o =84 (excitation overlap). measured at 2304 r/min, with. Clearly, the position signals show good agreement. Fig. 10 shows, and, where and. is defined as the position where the mechanical overlap occurs, i.e., where the rotor and stator poles start to overlap and it is calculated from the stator and rotor pole arcs. is defined as the position where the magnetic overlap occurs, obtained from experimental results. It can be observed that, for speeds above 800 r/min, is quite constant and around 3. This difference shows us that the magnetic overlap differs from the mechanical overlap by 3, which gives (15)
7 GALLEGOS-LÓPEZ et al.: A NEW SENSORLESS METHOD FOR SWITCHED RELUCTANCE MOTOR DRIVES 837 this information, the correct phase can be energized according to the desired direction of rotation. Once the first phase in energized, small probing pulses are injected in the phase next to be energized. The rotor position is extracted by the probing pulses, and it is used for phase commutation [1], [4]. It should be noted that a current sensor for each phase may be needed. In both cases, the motor must be accelerated from standstill to the speed where the waveform conditions are met and, therefore, sensorless pulses can be detected. Feedforward was chosen due to its simplicity and reduction of number of current sensors. Fig. 10. on = 45 ; o CGSM position estimation at 2304 r/min in single pulse with =80. Measured accuracy of CGSM in steady state. where represents the real position. Hence, the firing angles are shifted 3 (only is shown). Also, we observed that above 800 r/min is close to zero, which means that the position estimation hardly differs from the real position. In contrast, at low speed, there is a deviation of position estimation. This deviation in position estimation is caused by the accuracy in detecting. The most important factors influencing this detection are that the gain of the differentiator is sensitive to frequency, and the comparator amplifier may be offset, i.e.,. On the other hand, at high speed, the pulses may be delayed by the phase lag of the low-pass filters. However, position deviations can be corrected in the commutation angle controller as a function of speed. V. STARTUP It is a requirement of the CGSM that the phases conduct nonzero current, but, also, that the waveform resembles that of Fig. 3. To bring the motor into running mode, the following two options can be used. 1) Feedforward The motor is controlled feedforward in open-loop as a stepper motor [12]. A train of pulses with initial frequency is applied to the motor windings in a sequence according to the desired direction. The frequency is increased linearly, and it is assumed that the rotor follows it. 2) Active probing This method makes use of small current pulses in all phase windings in order to identify the inductance and. hence, rotor position at standstill. With A. Feedforward Method The goal is for the motor to generate enough torque to accelerate up to the speed at which the CGPE pulses can be detected. The takeover speed is defined as the speed at which the motor goes from being operated in feedforward to true sensorless operation (feedback). This method permits a reliable and smooth, but neither efficient nor optimal, startup of the motor, even under load. A train of pulses is applied to each phase in a sequence according to the direction of rotation. The dwell angle 3 is fixed and equal to 30. Each phase pulse train is phase shifted 30 (120 elec.). To accelerate the motor, the frequency is increased linearly to a value determined by a predefined takeover speed, while a 100% PWM duty cycle is applied and is decreased linearly to a final value according to the load torque at the takeover point. The startup procedure for a takeover speed of 500, 750, and 1000 r/min was simulated, and the PWM duty cycle was decreased to 33%, 50%, and 67%, respectively, in order to assure the current waveform where CGPE pulses can be detected. Fig. 11 shows the results. For the case of takeover at 1000 r/min, three traces are shown which correspond to different accelerations. The ramp time can be adjusted depending on the load torque. It is important to mention that the condition required for the CGSM may not be met for speeds below 200 r/min, for the particular drive analyzed here. Fig. 11 depicts and, corresponding to a takeover speed of 1000 r/min with a ramp time of 2 s. The ripple shows how the commutation angles move in order to match the load torque during the startup sequence (as a stepper). It is clear that occurs before, and occurs after. At the takeover speed, is around 43 and is around 73 ; at this time can be estimated. Fig. 11(c) depicts the instantaneous torque during startup. It shows that, at the beginning, there are significant torque oscillations, but these are limited at the takeover point. Fig. 12 depicts the experimental result during startup. The signal is measured with a 1024-line encoder. Initially, 76-Hz (380 r/min) excitation frequency is applied for a short period, and then, the frequency is increased linearly up to 230 Hz, at which the takeover speed of 1150 r/min is reached. The duty cycle is maintained at 100%. Once the takeover speed has been reached, the CGPE pulses can be used to commutate the 3 Dwell angle is defined as the commutation period over an electrical cycle, i.e., o 0 on.
8 838 IEEE TRANSACTIONS ON INDUSTRY APPLICATIONS, VOL. 34, NO. 4, JULY/AUGUST 1998 Fig. 12. CGSM feedforward startup (the signal is measured with a 1024-line encoder). Zoom of takeover at 1339 r/min with on = 50 ; o =80. (c) Fig. 11. CGSM feedforward startup (simulated). Speed for different accelerations A: 500 r/min, 1 s; B: 750 r/min, 1.5 s; C: 1000 r/min, 2 s; D: 1000 r/min, 1.5 s; E: 1000 r/min, 1 s. Firing angles. (c) Instantaneous torque. phases in closed loop. Fig. 12 shows, and CGPE measured during transition from open-loop to sensorless mode at takeover speed of 1339 r/min with. Fig. 13 shows and measured during the startup sequence. It can be seen that, at the beginning, the current is limited through chopping by a preset maximum current value and, as the speed goes up, the peak current is reduced. Once the takeover speed has been reached, the CGPE pulses can be used for commutation. Now, examples of sensorless closed-loop speed control are discussed. A PI controller acts on the PWM duty cycle for dynamic compensation. The firing angles remain fixed at. Fig. 13 shows and measured during transition from open-loop to sensorless mode with closed-loop speed control with a reference speed of 1092 r/min. An example of the drive s response to steps in speed reference is shown in Fig. 14 for sensorless mode and Fig. 14 with a 1024-line encoder. Clearly, the performance Fig. 13. Current waveform measured during feedforward startup. Takeover measured at speed = 1339 r/min with on =50 ; o =80, swapping to closed-loop speed control with a reference speed of 1092 r/min.
9 GALLEGOS-LÓPEZ et al.: A NEW SENSORLESS METHOD FOR SWITCHED RELUCTANCE MOTOR DRIVES 839 Fig. 16. sensor. Measured torque-speed characteristic with and without position to approximately 200 r/min, estimation of rotor position is not possible. However, at higher speeds, CGSM does not put any limitation on the torque-speed motor characteristic. Fig. 14. Zoom of speed transients. Sensorless CGSM on = 48 ; o =78. With sensor on =42 ; o =72. Fig. 15. Measured sensorless speed transients. Transient response to a load torque step of 0.42 N1m (0.6 p.u.). is comparable both with and without encoder feedback. Fig. 15 depicts a series of speed transients and Fig. 15 shows the sensorless drive s response to a step of 0.42 N m in load torque (0.6 p.u.), with and. This demonstrates that closed-loop CGSM could be acceptable in many low-cost variable-speed applications. Finally, Fig. 16 depicts the torque-speed characteristic of the three-phase 6/4 SRM used and also shows in which region the CGSM can be applied. It is clear that in the range from 0 VI. CONCLUSION This paper has experimentally demonstrated for the first time the functionality of a new rotor position estimation method for SR motors operated in PWM voltage control, detecting one rotor position per phase per electrical cycle, with no a priori knowledge of motor parameters. The method is comparable in performance and complexity to the back-emf method for brushless dc motors. Experimental results confirm the theory and prove the concept of the new CGSM. The position estimation can be detected with either one detection circuit per phase or, preferably, with just one for the lower transistor bus current, even with excitation overlap. It should be noted that the only cost added by this scheme is the detection circuit, which uses a few low-cost components. The firing angles can be varied freely with the condition of, which is otherwise necessary to produce adequate torque at high efficiency [13]. Feedforward (open loop) is used to accelerate the motor smoothly from zero speed up to a maximum frequency which is determined by the desired takeover speed. A closed-loop speed PI controller was implemented in sensorless mode, and a series of speed and torque transients demonstrated the feasibility of closing the speed loop by controlling the PWM duty cycle. In summary, we may conclude that the CGPE allows estimation of one rotor position per stroke with no a priori knowledge of the motor parameters, except the pole configuration. It is, therefore, applicable to most SRM topologies in a wide power and speed range and for most inverter topologies. The method allows the control of the SRM drive in two quadrants by controlling the commutation angles and PWM duty cycle, but could be expanded to four-quadrant operation or continuous generator operation. The scheme is mainly suited for medium- and high-speed applications, and this simple and low-cost implementation may allow the SRM technology into a range of air-moving and pump applications and even domestic appliances.
10 840 IEEE TRANSACTIONS ON INDUSTRY APPLICATIONS, VOL. 34, NO. 4, JULY/AUGUST 1998 ACKNOWLEDGMENT The authors would like to thank C. Cossar, I. Young, J. Kelly, and P. Miller for help in the test equipment. REFERENCES [1] P. P. Acarnley, R. J. Hill, and C. W. Hooper, Detection of rotor position in stepping and switched reluctance motors by monitoring of current waveforms, IEEE Trans. Ind. Electron., vol. 32, pp , June [2] J. P. Lyons, S. R. MacMinn, and M. A. Preston, Flux/current methods for SRM rotor position estimation, in Proc. IEEE-IAS Annu. Meeting, 1991, pp [3] G. Hedlund and H. Lundberg, Motor energizing circuit, U.S. Patent , Sept. 19, [4] S. R. MacMinn, W. J. Rzesos, P. M. Szczesny, and T. M. Jahns, Application of sensor integration techniques to switched reluctance motor drives, in Proc. IEEE-IAS Annu. Meeting, 1988, pp [5] M. Ehsani, I. Husain, and A. B. Kulkarni, Elimination of discrete position sensor and current sensor in switched reluctance motor drives, IEEE Trans. Ind. Applicat., vol. 28, pp , Jan./Feb [6] M. Ehsani, I. Husain, S. Mahajan, and K. R. Ramani, New modulation encoding techniques for indirect rotor position sensing in switched reluctance motors, IEEE Trans. Ind. Applicat., vol. 30, pp , Jan./Feb [7] I. Husain and M. Ehsani, Rotor position sensing in switched reluctance motor drives by measuring mutually induced voltages, IEEE Trans. Ind. Applicat., vol. 30, pp , May/June [8] P. Laurent, M. Gabsi, and M. Multon, Sensorless rotor position analysis using resonant method for switched reluctance motor, in Proc. IEEE- IAS Annu. Meeting, 1993, pp , [9] J. T. Bass, M. Ehsani, and T. J. E. Miller, Robust torque control of switched-reluctance motors without a shaft position sensor, IEEE Trans. Ind. Electron., vol. IE-33, pp , Aug [10] A. H. Lumsdaine and J. H. Lang, State observers for variable-reluctance motors, IEEE Trans. Ind. Applicat., vol. 37, pp , Mar./Apr [11] P. C. Kjær, F. Blaabjerg, J. K. Pedersen, P. Nielsen, and L. Andersen, A new indirect rotor position detection method for switched reluctance drives, in Proc. ICEM 94, Paris, France, 1994, vol. 2, pp [12] K. Iizuka, H. Uzuhashi, M. Kano, T. Endo, and K. Mohri, Microcomputer control for sensorless brushless motor, IEEE Trans. Ind. Applicat., vol. 21, pp , May/June [13] T. J. E. Miller, Switched reluctance motors and their control, in Monographs in Electrical and Electronic Engineering. Oxford, U.K.: Clarendon, Gabriel Gallegos-López (S 93), for a photograph and biography, see p. 451 of the May/June isssue of this TRANSACTIONS. Philip C. Kjaer (S 92 M 93), for a photograph and biography, see p. 451 of the May/June isssue of this TRANSACTIONS. Timothy J. E. Miller (M 74 SM 82 F 96), for a photograph and biography, see p. 428 of the May/June isssue of this TRANSACTIONS.
Mitigation of Cross-Saturation Effects in Resonance-Based Sensorless Switched Reluctance Drives
Mitigation of Cross-Saturation Effects in Resonance-Based Sensorless Switched Reluctance Drives K.R. Geldhof, A. Van den Bossche and J.A.A. Melkebeek Department of Electrical Energy, Systems and Automation
More informationDesign and development of Open loop CGSM for SR Motor
Journal of Scientific & Industrial Research Vol 72, May 213, pp 316-322 Design and development of Open loop CGSM for SR Motor Jignesh A. Makwana *, Pramod Agarwal, and S.P. Srivastava Electrical Engineering
More informationInductance Based Sensorless Control of Switched Reluctance Motor
I J C T A, 9(16), 2016, pp. 8135-8142 International Science Press Inductance Based Sensorless Control of Switched Reluctance Motor Pradeep Vishnuram*, Siva T.**, Sridhar R.* and Narayanamoorthi R.* ABSTRACT
More informationImplementation and position control performance of a position-sensorless IPM motor drive system based on magnetic saliency
Engineering Electrical Engineering fields Okayama University Year 1998 Implementation and position control performance of a position-sensorless IPM motor drive system based on magnetic saliency Satoshi
More informationControlling of Permanent Magnet Brushless DC Motor using Instrumentation Technique
Scientific Journal of Impact Factor(SJIF): 3.134 International Journal of Advance Engineering and Research Development Volume 2,Issue 1, January -2015 e-issn(o): 2348-4470 p-issn(p): 2348-6406 Controlling
More informationBECAUSE OF their low cost and high reliability, many
824 IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, VOL. 45, NO. 5, OCTOBER 1998 Sensorless Field Orientation Control of Induction Machines Based on a Mutual MRAS Scheme Li Zhen, Member, IEEE, and Longya
More informationLow Cost Power Converter with Improved Performance for Switched Reluctance Motor Drives
ISSN (Online) : 2319-8753 ISSN (Print) : 2347-6710 International Journal of Innovative Research in Science, Engineering and Technology Volume 3, Special Issue 3, March 2014 2014 International Conference
More informationSharmila Kumari.M, Sumathi.V, Vivekanandan S, Shobana S
International Journal of Scientific & Engineering Research, Volume 5, Issue 4, April-2014 388 PERFORMANCE IMPROVEMENT OF BLDC MOTOR USING FUZZY LOGIC CONTROLLER Sharmila Kumari.M, Sumathi.V, Vivekanandan
More informationIEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 14, NO. 3, MAY A Sliding Mode Current Control Scheme for PWM Brushless DC Motor Drives
IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 14, NO. 3, MAY 1999 541 A Sliding Mode Current Control Scheme for PWM Brushless DC Motor Drives Jessen Chen and Pei-Chong Tang Abstract This paper proposes
More informationA Review: Sensorless Control of Brushless DC Motor
A Review: Sensorless Control of Brushless DC Motor Neha Gupta, M.Tech Student, Department of Electrical Engineering, Madan Mohan Malaviya Engineering College, Gorakhpur 273010 (U.P), India Dr.A.K. Pandey,
More informationIN MANY industrial applications, ac machines are preferable
IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, VOL. 46, NO. 1, FEBRUARY 1999 111 Automatic IM Parameter Measurement Under Sensorless Field-Oriented Control Yih-Neng Lin and Chern-Lin Chen, Member, IEEE Abstract
More informationCHAPTER-III MODELING AND IMPLEMENTATION OF PMBLDC MOTOR DRIVE
CHAPTER-III MODELING AND IMPLEMENTATION OF PMBLDC MOTOR DRIVE 3.1 GENERAL The PMBLDC motors used in low power applications (up to 5kW) are fed from a single-phase AC source through a diode bridge rectifier
More informationSensorless control of BLDC motor based on Hysteresis comparator with PI control for speed regulation
Sensorless control of BLDC motor based on Hysteresis comparator with PI control for speed regulation Thirumoni.T 1,Femi.R 2 PG Student 1, Assistant Professor 2, Department of Electrical and Electronics
More informationFuzzy Logic Based Speed Control of BLDC Motor
Fuzzy Logic Based Speed Control of BLDC Motor Mahesh Sutar #1, Ashish Zanjade *2, Pankaj Salunkhe #3 # EXTC Department, Mumbai University. 1 Sutarmahesh4@gmail.com 2 Zanjade_aa@rediffmail.com 3 pasalunkhe@gmail.com
More informationFOR the last decade, many research efforts have been made
IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 19, NO. 6, NOVEMBER 2004 1601 A Novel Approach for Sensorless Control of PM Machines Down to Zero Speed Without Signal Injection or Special PWM Technique Chuanyang
More information3. What is the difference between Switched Reluctance motor and variable reluctance stepper motor?(may12)
EE6703 SPECIAL ELECTRICAL MACHINES UNIT III SWITCHED RELUCTANCE MOTOR PART A 1. What is switched reluctance motor? The switched reluctance motor is a doubly salient, singly excited motor. This means that
More informationCHAPTER 4 FUZZY BASED DYNAMIC PWM CONTROL
47 CHAPTER 4 FUZZY BASED DYNAMIC PWM CONTROL 4.1 INTRODUCTION Passive filters are used to minimize the harmonic components present in the stator voltage and current of the BLDC motor. Based on the design,
More informationAnalog Devices: High Efficiency, Low Cost, Sensorless Motor Control.
Analog Devices: High Efficiency, Low Cost, Sensorless Motor Control. Dr. Tom Flint, Analog Devices, Inc. Abstract In this paper we consider the sensorless control of two types of high efficiency electric
More informationCHAPTER 6 THREE-LEVEL INVERTER WITH LC FILTER
97 CHAPTER 6 THREE-LEVEL INVERTER WITH LC FILTER 6.1 INTRODUCTION Multi level inverters are proven to be an ideal technique for improving the voltage and current profile to closely match with the sinusoidal
More informationVolume 1, Number 1, 2015 Pages Jordan Journal of Electrical Engineering ISSN (Print): , ISSN (Online):
JJEE Volume, Number, 2 Pages 3-24 Jordan Journal of Electrical Engineering ISSN (Print): 249-96, ISSN (Online): 249-969 Analysis of Brushless DC Motor with Trapezoidal Back EMF using MATLAB Taha A. Hussein
More informationADVANCED ROTOR POSITION DETECTION TECHNIQUE FOR SENSORLESS BLDC MOTOR CONTROL
International Journal of Soft Computing and Engineering (IJSCE) ISSN: 3137, Volume, Issue-1, March 1 ADVANCED ROTOR POSITION DETECTION TECHNIQUE FOR SENSORLESS BLDC MOTOR CONTROL S.JOSHUWA, E.SATHISHKUMAR,
More informationAnalysis of Soft-switching Converters for Switched Reluctance Motor Drives for Electric Vehicles
Journal of sian Electric Vehicles, Volume 7, Number 1, June 2009 nalysis of Soft-switching Converters for Switched Reluctance Motor Drives for Electric Vehicles Tze Wood Ching Department of Electromechanical
More informationSpeed Control of BLDC Motor Using FPGA
Speed Control of BLDC Motor Using FPGA Jisha Kuruvilla 1, Basil George 2, Deepu K 3, Gokul P.T 4, Mathew Jose 5 Assistant Professor, Dept. of EEE, Mar Athanasius College of Engineering, Kothamangalam,
More informationEEE, St Peter s University, India 2 EEE, Vel s University, India
Torque ripple reduction of switched reluctance motor drives below the base speed using commutation angles control S.Vetriselvan 1, Dr.S.Latha 2, M.Saravanan 3 1, 3 EEE, St Peter s University, India 2 EEE,
More informationSimulation Study of MOSFET Based Drive Circuit Design of Sensorless BLDC Motor for Space Vehicle
Simulation Study of MOSFET Based Drive Circuit Design of Sensorless BLDC Motor for Space Vehicle Rajashekar J.S. 1 and Dr. S.C. Prasanna Kumar 2 1 Associate Professor, Dept. of Instrumentation Technology,
More informationSPEED CONTROL OF SENSORLESS BLDC MOTOR WITH FIELD ORIENTED CONTROL
ISSN: 2349-2503 SPEED CONTROL OF SENSORLESS BLDC MOTOR WITH FIELD ORIENTED CONTROL JMuthupandi 1 DCitharthan 2 MVaratharaj 3 1 (UG Scholar/EEE department/ Christ the king engg college/ Coimbatore/India/
More informationTRACK VOLTAGE APPROACH USING CONVENTIONAL PI AND FUZZY LOGIC CONTROLLER FOR PERFORMANCE COMPARISON OF BLDC MOTOR DRIVE SYSTEM FED BY CUK CONVERTER
International Journal of Mechanical Engineering and Technology (IJMET) Volume 9, Issue 12, December 2018, pp. 778 786, Article ID: IJMET_09_12_078 Available online at http://www.ia aeme.com/ijmet/issues.asp?jtype=ijmet&vtype=
More informationA Practical Primer On Motor Drives (Part 13): Motor Drive Control Architectures And Algorithms
ISSUE: February 2017 A Practical Primer On Motor Drives (Part 13): Motor Drive Control Architectures And Algorithms by Ken Johnson, Teledyne LeCroy, Chestnut Ridge, N.Y. Part 12 began the explanation of
More informationRECENTLY, the brushless dc (BLDC) motor is becoming
438 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 23, NO. 1, JANUARY 2008 Position Sensorless Control for Four-Switch Three-Phase Brushless DC Motor Drives Cheng-Tsung Lin, Chung-Wen Hung, and Chih-Wen
More informationStep vs. Servo Selecting the Best
Step vs. Servo Selecting the Best Dan Jones Over the many years, there have been many technical papers and articles about which motor is the best. The short and sweet answer is let s talk about the application.
More informationCHAPTER 2 CURRENT SOURCE INVERTER FOR IM CONTROL
9 CHAPTER 2 CURRENT SOURCE INVERTER FOR IM CONTROL 2.1 INTRODUCTION AC drives are mainly classified into direct and indirect converter drives. In direct converters (cycloconverters), the AC power is fed
More informationBrushless Motor without a Shaft-Mounted Position Sensor. Tsunehiro Endo Fumio Tajima Member Member. Summary
Paper UDC 621.313.3-573: 621.316.71:681.532.8:621.382 Brushless Motor without a Shaft-Mounted Position Sensor By Tsunehiro Endo Fumio Tajima Member Member Kenichi Iizuka Member Summary Hideo Uzuhashi Non-member
More informationAcoustic Noise Reduction in Single Phase SRM Drives by Random Switching Technique
Vol:3, o:, 9 Acoustic oise Reduction in Single Phase SRM Drives by Random Switching Technique Minh-Khai guyen, Young-Gook Jung, and Young-Cheol Lim International Science Index, Electronics and Communication
More informationPOWER FACTOR IMPROVEMENT USING CURRENT SOURCE RECTIFIER WITH BATTERY CHARGING CAPABILITY IN REGENERATIVE MODE OF SRM
POWER FACTOR IMPROVEMENT USING CURRENT SOURCE RECTIFIER WITH BATTERY CHARGING CAPABILITY IN REGENERATIVE MODE OF SRM M.Rajesh 1, M.Sunil Kumar 2 1 P.G.Student, 2 Asst.Prof, Dept.of Eee, D.V.R & Dr.H.S
More informationSpeed control of sensorless BLDC motor with two side chopping PWM
IOSR Journal of Electrical and Electronics Engineering (IOSR-JEEE) e-issn: 2278-1676,p-ISSN: 2320-3331, Volume 6, Issue 3 (May. - Jun. 2013), PP 16-20 Speed control of sensorless BLDC motor with two side
More informationA CSC Converter fed Sensorless BLDC Motor Drive
A CSC Converter fed Sensorless BLDC Motor Drive Anit K. Jose P G Student St Joseph's College of Engg Pala Bissy Babu Assistant Professor St Joseph's College of Engg Pala Abstract: The Brushless Direct
More informationLow-Cost Sensorless Control of Brushless dc Motors with Improved Speed Range
Low-Cost Sensorless Control of Brushless dc Motors with Improved Speed Range Gui-Jia Su and John W. McKeever Oak Ridge National Laboratory National Transportation Resrch Center 26 Cherahala Blvd. Knoxville,
More informationA Novel Control Method for Input Output Harmonic Elimination of the PWM Boost Type Rectifier Under Unbalanced Operating Conditions
IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 16, NO. 5, SEPTEMBER 2001 603 A Novel Control Method for Input Output Harmonic Elimination of the PWM Boost Type Rectifier Under Unbalanced Operating Conditions
More informationABSTRACT I. INTRODUCTION
2017 IJSRST Volume 3 Issue 8 Print ISSN: 2395-6011 Online ISSN: 2395-602X Themed Section: Science and Technology A Novel Zeta Converter with Pi Controller for Power Factor Correction in Induction Motor
More informationPWM Control of Asymmetrical Converter Fed Switched Reluctance Motor Drive
, 23-25 October, 2013, San Francisco, USA PWM Control of Asymmetrical Converter Fed Switched Reluctance Motor Drive P.Srinivas and P.V.N.Prasad Abstract The Switched Reluctance Motor (SRM) drive has evolved
More informationA COMPARISON STUDY OF THE COMMUTATION METHODS FOR THE THREE-PHASE PERMANENT MAGNET BRUSHLESS DC MOTOR
A COMPARISON STUDY OF THE COMMUTATION METHODS FOR THE THREE-PHASE PERMANENT MAGNET BRUSHLESS DC MOTOR Shiyoung Lee, Ph.D. Pennsylvania State University Berks Campus Room 120 Luerssen Building, Tulpehocken
More informationSPEED CONTROL OF BRUSHLES DC MOTOR
SPEED CONTROL OF BRUSHLES DC MOTOR Kajal D. Parsana 1, Prof. H.M. Karkar 2, Prof. I.N. Trivedi 3 1 Department of Electrical Engineering, Atmiya Institute of Technology & Science, Rajkot, India. kajal.parsana@gmail.com
More informationINTERNATIONAL JOURNAL OF PURE AND APPLIED RESEARCH IN ENGINEERING AND TECHNOLOGY
INTERNATIONAL JOURNAL OF PURE AND APPLIED RESEARCH IN ENGINEERING AND TECHNOLOGY A PATH FOR HORIZING YOUR INNOVATIVE WORK SENSORLESS BLDC MOTOR CONTROL IN MATLAB SIMULINK ANKITA A KANEKAR, V. K. JOSEPH
More informationPULSEWIDTH modulation (PWM) has been widely used
IEEE TRANSACTIONS ON INDUSTRY APPLICATIONS, VOL. 34, NO. 4, JULY/AUGUST 1998 861 Space-Vector Analysis and Modulation Issues of Passively Clamped Quasi-Resonant Inverters Braz J. Cardoso Filho and Thomas
More informationNew Converter for Switched Reluctance Motor Drive With Wide Speed Range Operation
2011 2nd Power Electronics, Drive Systems and Technologies Conference New Converter for Switched Reluctance Motor Drive With Wide Speed Range Operation Adel Deris Zadeh Department of Electrical Engineering
More informationCHAPTER 1 INTRODUCTION
CHAPTER 1 INTRODUCTION 1.1 Introduction Power semiconductor devices constitute the heart of the modern power electronics, and are being extensively used in power electronic converters in the form of a
More informationCHAPTER 2 D-Q AXES FLUX MEASUREMENT IN SYNCHRONOUS MACHINES
22 CHAPTER 2 D-Q AXES FLUX MEASUREMENT IN SYNCHRONOUS MACHINES 2.1 INTRODUCTION For the accurate analysis of synchronous machines using the two axis frame models, the d-axis and q-axis magnetic characteristics
More informationPerformance analysis of Switched Reluctance Motor using Linear Model
Performance analysis of Switched Reluctance Motor using Linear Model M. Venkatesh, Rama Krishna Raghutu Dept. of Electrical & Electronics Engineering, GMRIT, RAJAM E-mail: venkateshmudadla@gmail.com, ramakrishnaree@gmail.com
More informationL E C T U R E R, E L E C T R I C A L A N D M I C R O E L E C T R O N I C E N G I N E E R I N G
P R O F. S L A C K L E C T U R E R, E L E C T R I C A L A N D M I C R O E L E C T R O N I C E N G I N E E R I N G G B S E E E @ R I T. E D U B L D I N G 9, O F F I C E 0 9-3 1 8 9 ( 5 8 5 ) 4 7 5-5 1 0
More informationIEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 23, NO. 6, NOVEMBER
IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 23, NO. 6, NOVEMBER 2008 3079 A Novel Position Sensorless Control of a Four-Switch, Brushless DC Motor Drive Without Phase Shifter Abolfazl Halvaei Niasar,
More informationBLDC Motor Drive with Power Factor Correction Using PWM Rectifier
BLDC Motor Drive with Power Factor Correction Using PWM Rectifier P. Sarala, S.F. Kodad and B. Sarvesh Abstract Major constraints while using motor drive system are efficiency and cost. Commutation in
More informationDigital PWM Techniques and Commutation for Brushless DC Motor Control Applications: Review
Digital PWM Techniques and Commutation for Brushless DC Motor Control Applications: Review Prof. S.L. Tade 1, Ravindra Sor 2 & S.V. Kinkar 3 Professor, Dept. of E&TC, PCCOE, Pune, India 1 Scientist, ARDE-DRDO,
More informationDesign of A Closed Loop Speed Control For BLDC Motor
International Refereed Journal of Engineering and Science (IRJES) ISSN (Online) 2319-183X, (Print) 2319-1821 Volume 3, Issue 11 (November 214), PP.17-111 Design of A Closed Loop Speed Control For BLDC
More informationATYPICAL high-power gate-turn-off (GTO) currentsource
1278 IEEE TRANSACTIONS ON INDUSTRY APPLICATIONS, VOL. 34, NO. 6, NOVEMBER/DECEMBER 1998 A Novel Power Factor Control Scheme for High-Power GTO Current-Source Converter Yuan Xiao, Bin Wu, Member, IEEE,
More informationFuzzy Logic Controller Based Direct Torque Control of PMBLDC Motor
Fuzzy Logic Controller Based Direct Torque Control of PMBLDC Motor Madasamy P 1, Ramadas K 2, Nagapriya S 3 1, 2, 3 Department of Electrical and Electronics Engineering, Alagappa Chettiar College of Engineering
More informationSensorless Control of a Switched Reluctance Motor by Using Sliding Mode Observer
Sensorless Control of a Switched Reluctance Motor by Using Sliding Mode Observer M.Ravikanth M Tech Student Department of PE Siddhartha Institute of Engineering & Technology ABSTRACT This paper presents
More informationCHAPTER 6 CURRENT REGULATED PWM SCHEME BASED FOUR- SWITCH THREE-PHASE BRUSHLESS DC MOTOR DRIVE
125 CHAPTER 6 CURRENT REGULATED PWM SCHEME BASED FOUR- SWITCH THREE-PHASE BRUSHLESS DC MOTOR DRIVE 6.1 INTRODUCTION Permanent magnet motors with trapezoidal back EMF and sinusoidal back EMF have several
More informationConstruction of a Low Cost Asymmetric Bridge Converter for Switched Reluctance Motor Drive
Construction of a Low Cost Asymmetric Bridge Converter for Switched Reluctance Motor Drive E.Afjei 1, A.Siadatan 2 and M.Rafiee 3 1- Department of Electrical Eng., Faculty of Electrical & Computer Eng.,
More informationPage ENSC387 - Introduction to Electro-Mechanical Sensors and Actuators: Simon Fraser University Engineering Science
Motor Driver and Feedback Control: The feedback control system of a dc motor typically consists of a microcontroller, which provides drive commands (rotation and direction) to the driver. The driver is
More informationSensorless Control of a Novel IPMSM Based on High-Frequency Injection
Sensorless Control of a Novel IPMSM Based on High-Frequency Injection Xiaocan Wang*,Wei Xie**, Ralph Kennel*, Dieter Gerling** Institute for Electrical Drive Systems and Power Electronics,Technical University
More informationInfluence of Electrical Eigenfrequencies on Damped Voltage Resonance Based Sensorless Control of Switched Reluctance Drives
Influence of Electrical Eigenfrequencies on Damped Voltage Resonance ased Sensorless Control of Switched Reluctance Drives K.R. Geldhof, A. Van den ossche and J.A.A. Melkebeek Department of Electrical
More informationReduction of Harmonics and Torque Ripples of BLDC Motor by Cascaded H-Bridge Multi Level Inverter Using Current and Speed Control Techniques
Reduction of Harmonics and Torque Ripples of BLDC Motor by Cascaded H-Bridge Multi Level Inverter Using Current and Speed Control Techniques A. Sneha M.Tech. Student Scholar Department of Electrical &
More informationPART 2 - ACTUATORS. 6.0 Stepper Motors. 6.1 Principle of Operation
6.1 Principle of Operation PART 2 - ACTUATORS 6.0 The actuator is the device that mechanically drives a dynamic system - Stepper motors are a popular type of actuators - Unlike continuous-drive actuators,
More informationExperiment 3. Performance of an induction motor drive under V/f and rotor flux oriented controllers.
University of New South Wales School of Electrical Engineering & Telecommunications ELEC4613 - ELECTRIC DRIVE SYSTEMS Experiment 3. Performance of an induction motor drive under V/f and rotor flux oriented
More informationSIMULATION AND IMPLEMENTATION OF CURRENT CONTROL OF BLDC MOTOR BASED ON A COMMON DC SIGNAL
SIMULATION AND IMPLEMENTATION OF CURRENT CONTROL OF BLDC MOTOR BASED ON A COMMON DC SIGNAL J.Karthikeyan* Dr.R.Dhanasekaran** * Research Scholar, Anna University, Coimbatore ** Research Supervisor, Anna
More informationBLOCK DIAGRAM OF THE UC3625
U-115 APPLICATION NOTE New Integrated Circuit Produces Robust, Noise Immune System For Brushless DC Motors Bob Neidorff, Unitrode Integrated Circuits Corp., Merrimack, NH Abstract A new integrated circuit
More informationLatest Control Technology in Inverters and Servo Systems
Latest Control Technology in Inverters and Servo Systems Takao Yanase Hidetoshi Umida Takashi Aihara. Introduction Inverters and servo systems have achieved small size and high performance through the
More informationSwinburne Research Bank
Swinburne Research Bank http://researchbank.swinburne.edu.au Tashakori, A., & Ektesabi, M. (2013). A simple fault tolerant control system for Hall Effect sensors failure of BLDC motor. Originally published
More informationcombine regular DC-motors with a gear-box and an encoder/potentiometer to form a position control loop can only assume a limited range of angular
Embedded Control Applications II MP10-1 Embedded Control Applications II MP10-2 week lecture topics 10 Embedded Control Applications II - Servo-motor control - Stepper motor control - The control of a
More informationPOWER- SWITCHING CONVERTERS Medium and High Power
POWER- SWITCHING CONVERTERS Medium and High Power By Dorin O. Neacsu Taylor &. Francis Taylor & Francis Group Boca Raton London New York CRC is an imprint of the Taylor & Francis Group, an informa business
More informationAnalysis of Voltage Source Inverters using Space Vector PWM for Induction Motor Drive
IOSR Journal of Electrical and Electronics Engineering (IOSR-JEEE) ISSN: 2278-1676 Volume 2, Issue 6 (Sep-Oct. 2012), PP 14-19 Analysis of Voltage Source Inverters using Space Vector PWM for Induction
More informationNovel SRM Drive Systems Using Variable DC-Link Voltage
Novel SRM Drive Systems Using Variable DC-Link Voltage 1 JPE 11-3-1 Novel SRM Drive Systems Using Variable DC-Link Voltage Do-Hyun Jang Dept. of Electrical Engineering, Hoseo University, Asan, Korea Abstract
More informationCHAPTER 2 STATE SPACE MODEL OF BLDC MOTOR
29 CHAPTER 2 STATE SPACE MODEL OF BLDC MOTOR 2.1 INTRODUCTION Modelling and simulation have been an essential part of control system. The importance of modelling and simulation is increasing with the combination
More informationTHE operation of induction motors in the so-called constant
IEEE TRANSACTIONS ON INDUSTRY APPLICATIONS, VOL. 34, NO. 4, JULY/AUGUST 1998 813 A New Induction Motor V/f Control Method Capable of High-Performance Regulation at Low Speeds Alfredo Muñoz-García, Thomas
More informationIT HAS LONG been recognized that bearing damage can be
1042 IEEE TRANSACTIONS ON INDUSTRY APPLICATIONS, VOL. 34, NO. 5, SEPTEMBER/OCTOBER 1998 Bearing Currents and Shaft Voltages of an Induction Motor Under Hard- and Soft-Switching Inverter Excitation Shaotang
More informationSensorless Speed Control of FSTPI Fed Brushless DC Motor Drive Using Terminal Voltage Sensing Method
International Journal of Soft Computing and Engineering (IJSCE) ISSN: 2231-237, Volume-4, Issue-1, March 214 Sensorless Speed Control of FSTPI Fed Brushless DC Motor Drive Using Terminal Voltage Sensing
More informationInvestigations of Fuzzy Logic Controller for Sensorless Switched Reluctance Motor Drive
IOSR Journal of Electrical and Electronics Engineering (IOSR-JEEE) e-issn: 2278-1676,p-ISSN: 2320-3331, Volume 11, Issue 1 Ver. I (Jan Feb. 2016), PP 30-35 www.iosrjournals.org Investigations of Fuzzy
More informationApplying POWERSYS and SIMULINK to Modeling Switched Reluctance Motor
Tamkang Journal of Science and Engineering, Vol. 12, No. 4, pp. 429 438 (2009) 429 Applying POWERSYS and SIMULINK to Modeling Switched Reluctance Motor K. I. Hwu Institute of Electrical Engineering, National
More informationIEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, VOL. 53, NO. 2, APRIL
IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS, VOL. 53, NO. 2, APRIL 2006 399 Sensorless Speed Control of Nonsalient Permanent-Magnet Synchronous Motor Using Rotor-Position-Tracking PI Controller Jul-Ki
More informationA NEW C-DUMP CONVERTER WITH POWER FACTOR CORRECTION FEATURE FOR BLDC DRIVE
International Journal of Electrical and Electronics Engineering Research (IJEEER) ISSN 2250-155X Vol. 3, Issue 3, Aug 2013, 59-70 TJPRC Pvt. Ltd. A NEW C-DUMP CONVERTER WITH POWER FACTOR CORRECTION FEATURE
More informationExtended Speed Current Profiling Algorithm for Low Torque Ripple SRM using Model Predictive Control
Extended Speed Current Profiling Algorithm for Low Torque Ripple SRM using Model Predictive Control Siddharth Mehta, Md. Ashfanoor Kabir and Iqbal Husain FREEDM Systems Center, Department of Electrical
More informationELECTRONIC CONTROL OF A.C. MOTORS
CONTENTS C H A P T E R46 Learning Objectives es Classes of Electronic AC Drives Variable Frequency Speed Control of a SCIM Variable Voltage Speed Control of a SCIM Chopper Speed Control of a WRIM Electronic
More informationSimulation of Solar Powered PMBLDC Motor Drive
Simulation of Solar Powered PMBLDC Motor Drive 1 Deepa A B, 2 Prof. Maheshkant pawar 1 Students, 2 Assistant Professor P.D.A College of Engineering Abstract - Recent global developments lead to the use
More informationIN RECENT years, sensorless or self-sensing control of
IEEE TRANSACTIONS ON INDUSTRY APPLICATIONS, VOL. 34, NO. 5, SEPTEMBER/OCTOBER 1998 1097 Using Multiple Saliencies for the Estimation of Flux, Position, and Velocity in AC Machines Michael W. Degner and
More informationA New Class of Resonant Discharge Drive Topology for Switched Reluctance Motor
A New Class of Resonant Discharge Drive Topology for Switched Reluctance Motor M. Asgar* and E. Afjei** Downloaded from ijeee.iust.ac.ir at : IRDT on Tuesday May 8th 18 Abstract: Switched reluctance motor
More informationFuzzy Logic Controller Based Four Phase Switched Reluctance Motor
Fuzzy Logic Controller Based Four Phase Switched Reluctance Motor KODEM DEVENDRA PRASAD M-tech Student Scholar Department of Electrical & Electronics Engineering, ANURAG FROUP OF INSTITUTIONS (CVSR) Ghatkesar
More informationTO LIMIT degradation in power quality caused by nonlinear
1152 IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 13, NO. 6, NOVEMBER 1998 Optimal Current Programming in Three-Phase High-Power-Factor Rectifier Based on Two Boost Converters Predrag Pejović, Member,
More informationRotor Position Detection in Switched Reluctance Drives
Rotor Position Detection in Switched Reluctance Drives Ibrahim H Al-Bahadly Institute of Information Sciences and Technology Massey University, Palmerston North, New Zealand Abstract:- The performance
More informationCHAPTER 2 LITERATURE REVIEW
20 CHAPTER 2 LITERATURE REVIEW 2.1 INTRODUCTION The two major challenges on which the improvements required for the permanent magnet brushless DC motor drive systems are: a) Harmonics present in the voltage
More informationPWM SWITCHING STRATEGY FOR TORQUE RIPPLE MINIMIZATION IN BLDC MOTOR
Journal of ELECTRICAL ENGINEERING, VOL. 62, NO. 3, 2011, 141 146 PWM SWITCHING STRATEGY FOR TORQUE RIPPLE MINIMIZATION IN BLDC MOTOR Wael A. Salah Dahaman Ishak Khaleel J. Hammadi This paper describes
More informationCURRENT FOLLOWER APPROACH BASED PI AND FUZZY LOGIC CONTROLLERS FOR BLDC MOTOR DRIVE SYSTEM FED FROM CUK CONVERTER
CURRENT FOLLOWER APPROACH BASED PI AND FUZZY LOGIC CONTROLLERS FOR BLDC MOTOR DRIVE SYSTEM FED FROM CUK CONVERTER N. Mohanraj and R. Sankaran Shanmugha Arts, Science, Technology and Research Academy University,
More informationAC Voltage and Current Sensorless Control of Three-Phase PWM Rectifiers
IEEE TRANSACTIONS ON POWER ELECTRONICS, VOL. 17, NO. 6, NOVEMBER 2002 883 AC Voltage and Current Sensorless Control of Three-Phase PWM Rectifiers Dong-Choon Lee, Member, IEEE, and Dae-Sik Lim Abstract
More informationANALYSIS OF POWER QUALITY IMPROVEMENT OF BLDC MOTOR DRIVE USING CUK CONVERTER OPERATING IN DISCONTINUOUS CONDUCTION MODE
ANALYSIS OF POWER QUALITY IMPROVEMENT OF BLDC MOTOR DRIVE USING CUK CONVERTER OPERATING IN DISCONTINUOUS CONDUCTION MODE Bhushan P. Mokal 1, Dr. K. Vadirajacharya 2 1,2 Department of Electrical Engineering,Dr.
More informationFeedback Devices. By John Mazurkiewicz. Baldor Electric
Feedback Devices By John Mazurkiewicz Baldor Electric Closed loop systems use feedback signals for stabilization, speed and position information. There are a variety of devices to provide this data, such
More informationEstimation of Vibrations in Switched Reluctance Motor Drives
American Journal of Applied Sciences 2 (4): 79-795, 2005 ISS 546-9239 Science Publications, 2005 Estimation of Vibrations in Switched Reluctance Motor Drives S. Balamurugan and R. Arumugam Power System
More informationRenewable Energy Based Interleaved Boost Converter
Renewable Energy Based Interleaved Boost Converter Pradeepakumara V 1, Nagabhushan patil 2 PG Scholar 1, Professor 2 Department of EEE Poojya Doddappa Appa College of Engineering, Kalaburagi, Karnataka,
More informationMSK4310 Demonstration
MSK4310 Demonstration The MSK4310 3 Phase DC Brushless Speed Controller hybrid is a complete closed loop velocity mode controller for driving a brushless motor. It requires no external velocity feedback
More informationPWM SWITCHING STRATEGY FOR TORQUE RIPPLE MINIMIZATION IN BLDC MOTOR
Journal of ELECTRICAL ENGINEERING, VOL. 62, NO. 3, 11, 1 6 01 01 02 02 03 PWM SWITCHING STRATEGY FOR TORQUE 03 04 04 RIPPLE MINIMIZATION IN BLDC MOTOR 05 05 06 06 07 Wael A. Salah Dahaman Ishak Khaleel
More informationAnalysis of Indirect Temperature-Rise Tests of Induction Machines Using Time Stepping Finite Element Method
IEEE TRANSACTIONS ON ENERGY CONVERSION, VOL. 16, NO. 1, MARCH 2001 55 Analysis of Indirect Temperature-Rise Tests of Induction Machines Using Time Stepping Finite Element Method S. L. Ho and W. N. Fu Abstract
More informationUG Student, Department of Electrical Engineering, Gurunanak Institute of Engineering & Technology, Nagpur
A Review: Modelling of Permanent Magnet Brushless DC Motor Drive Ravikiran H. Rushiya 1, Renish M. George 2, Prateek R. Dongre 3, Swapnil B. Borkar 4, Shankar S. Soneker 5 And S. W. Khubalkar 6 1,2,3,4,5
More information