INSTALLATION INSTRUCTIONS: ULTRA FRONT FENDER FLARES
|
|
- Marjory Wilkins
- 6 years ago
- Views:
Transcription
1 INSTALLATION INSTRUCTIONS: ULTRA FRONT FENDER FLARES Thank you for your purchase of Crawler Conceptz Ultra Series Front Fender Flares. While these flares are easily installed with basic hand tools and general mechanical knowledge, it is advised to seek help from a professional. These instructions are a step by step tutorial on how to remove the factory flares and install the Ultra Series Front Fender Flares. However, if you need further direction please contact us at (951) or Support@crawlerconceptz.com. REQUIRED TOOLS 10MM wrench (2) 1/2 combo wrenches (2) 7/16 combo wrenches Door panel removal tool Drill gun Drill bits stepping up to 3/8 1/4 drill bit Paint Felt pen Cutoff wheel or shears (if reusing factory liner) PART LIST (2) ULTRA SERIES FRONT FENDER FLARES (2) SMALL REINFORCEMENT BRACKETS (2) LARGE REINFORCEMENT BRACKETS (2) L-SHAPED BRACKETS (6) 10MM bolt reused from factory flare (2) 10 MM long nut (2) 1/4 Gr. 8 Flat Washer (2) 1/4-20x1 1/4 Gr. 8 Bolt (2) 1/4-20 Gr. 8 Nut (46) 5/16 Gr. 8 FLAT WASHER (28) 5/16-18x1 1/4 Gr. 8 BOLT (8) 5/16-18 CLIP NUT NOTE: INSTRUCTIONS WERE DONE USING A 2014 WRANGLER UNLIMITED AND AN ULTRA FRONT FENDER FLARES. WHILE THIS BUMPER FITS 2007 PRESENT JEEP WRANGLERS, THERE MAY BE SOME DIFFERENCES BETWEEN MODEL YEARS. 1
2 STEP 1: REMOVE FACTORY FLARE Step 1a Lift the vehicle and remove the tire on the side you are working on. Step 1b Using a 10mm wrench and Door Panel Removal tool, remove the long nut (blue circle) and 6 push in retainers (green circles) while holding the factory inner fender liner on. Save all parts for later if reusing the factory inner fender liner. (pic 1) PIC 1 Step 1c Disconnect the marker light harness (pic 2) and the marker light wire retainer (pic 3). Once done, remove the inner fender liner by prying and twisting until free. PIC 2 PIC 3 2
3 STEP 1: REMOVE FACTORY FLARE Step 1d Remove the (5) 10mm bolts (green circles) and save for later use. (pic 4) PIC 4 Step 1e Remove the factor flare by pulling. Be extremely careful as the sheet metal is thin and can easily be bent. (pic 5) PIC 5 Step 1f Remove any retaining clips that did not come free with the bumper by reaching behind the clip and pinching it from the backside. (pic 5) Clean any debris or dirt under the factory flare. PIC 6 3
4 STEP 2: DRILLING NOTE: Picture shows Driver Side bracket. Step 2a Install 4 nut clips (green circles) onto the Large Reinforcement Bracket. (pic 7) PIC 7 Step 2b Loosely install the Large Reinforcement bracket (green circles). Align the nut clips (blue circles) so that bolts ban be threaded when test fitting the flare. (pic 8) PIC 8 Step 2c Install the flare with as many 5/16 nuts and bolts as possible. This will help when marking the holes for drilling. Once all are loosely threaded, tighten several. (pic 9) PIC 9 Step 2d With a felt pen mark the three holes (green arrows). Remove the fender and Large Reinforcement Bracket. Drill all three marked holes to 3/8. Drill slowly and gradually step up in size to 3/8, as the sheet metal can easily be twisted. (pic 10) PIC 10 4
5 STEP 2: DRILLING Step 2e Install the Small Bracket, but only use the two outermost bolts (green arrows). Mark the two inner holes for drilling (blue arrows). Remove the bracket and drill the marked holes to 3/8. Drilling through two of the holes in Step 2d can make this easier. (pic 10) PIC 11 NOTE: There is a left and right side as well as a top and bottom. Make sure to orient correctly. STEP 3: INSTALL ULTRA FRONT FLARE DO NOT TIGHTEN ANY BOLT UNTIL ALL BOLTS ARE STARTED. Step 3a In order, install the Large Bracket (green arrow) using the (3) 10mm bolts retained from Step 1d, Ultra Front Fender Flare (white arrow), and then the Small Bracket (blue arrow). Start all (14) 5/16 bolts before tightening. (pic 12) PIC 12 NOTE: If reusing the factory inner fender liner continue to Step 4. If using an after market inner fender liner, finish with those instructions. If using Crawler Conceptz Aluminum Front Inner Panels, continue with STEP 2 in those instructions 5
6 STEP 4: TRIM INNER FENDER LINER Step 4a Put the factory liner in place and using a felt tip pen mark along the edge for trimming. (pic 13) PIC 13 Step 4b Using a quality shear, cut the fender liner along the line made in Step 4a. Repeat these two steps until you have perfect fit. (pic 14) PIC 14 Step 4c Install the fender liner using the 10mm long nut from Step 1b (blue circle). (pic 15) PIC 15 6
7 STEP 4: TRIM INNER FENDER LINER Step 4d Use the factory 10mm bolt saved from Step 1b to install the L bracket. Make a mark on the bottom side of the L bracket. Remove the liner and drill a 1/4 on the marked spot. (pic 16) PIC 16 Step 4e Install the L bracket to the liner using (2) 7/16 combo wrenches. (pic 17) PIC 17 Step 4e Reinstall the liner using the 10mm long nut (blue circle) and 10 mm bolt (green circle). (pic 18) PIC 18 7
8 Thanks again for your purchase from Crawler Conceptz. We hope you enjoy your new Ultra Series Fender Flares and if you have any other needs please contact us at (951) or 8
JK FRONT FENDER FLARE INSTALLATION INSTRUCTIONS
JK FRONT FENDER FLARE INSTALLATION INSTRUCTIONS TOOLS NEEDED 3/16 Allen Wrench 1/2 Socket or wrench 10mm Socket Flat head screwdriver HARDWARE 5/16 x 3/4 button heads (14) 5/16 x 1 button heads (8) 5/16
More informationBushwacker Jeep Flat Style Fender Flares Front Pair
Bushwacker Jeep Flat Style Fender Flares Front Pair Note: These instructions involve cutting parts of your vehicle. Please read all instructions prior to starting. Installation Time: 3-4 Hours Tools Required:
More informationBushwacker Jeep Flat Style Fender Flares Rear Pair (JK Wrangler 2dr)
Bushwacker Jeep Flat Style Fender Flares Rear Pair (JK Wrangler 2dr) Note: These instructions involve cutting parts of your vehicle. Please read all instructions prior to starting. Installation Time: 3-4
More informationFront Armor Fender. Page 1/12. Part # Copyright 2016 Omix-Ada, Inc.
Page 1/12 Part #11615.01 Page 2/12 1 5 2 3 4 6 7 Components 1. Right Front Fender (1) 2. Left Front Fender (1) 3. Right Front Mounting Bracket (1) 4. Left Front Mounting Bracket (1) 5. Cowl Bracket (2)
More informationInstallation Instructions: JK Inner Fender Liners Part Number(s): & Ratchet 3/8 & 7/16 Sockets. Plastic Clip Removal Tool
Page 1 of 5 Proudly Made In USA Installation Instructions: JK Inner Fender Liners Part Number(s): 400.300.170 & 400.300.180 Vehicle Fitment: 2007 - Present Jeep Wrangler & Unlimited Parts List Qty: 1 Driver
More informationElite Series Fender Flares
Page 1 of 8 Installation Instructions I - Sheet Number I606RPG Rev.B Important Safety Information Tools Required Contents Elite Series Fender Flares Preparation Before Painting / Installation NOTE Actual
More information2016 Current Toyota Tacoma HoneyBadger Front Bumper Installation Instructions
2016 Current Toyota Tacoma HoneyBadger Front Bumper Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake.
More informationFRONT BUMPER INSTALLATION INSTRUCTIONS Toyota 4Runner
Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 FRONT BUMPER INSTALLATION INSTRUCTIONS 2003-2009 Toyota 4Runner Please read before beginning Stainless steel hardware may bind
More informationJeep Wrangler JK & 4-Door Front Pair Part # Revision H
Jeep Wrangler JK 2007 2 & 4-Door Front Pair Part # 10045 Revision H 03-25-09 Step 1: Prior to Installation: A) Bushwacker only approves installing the flares according to these written instructions with
More informationInstallation Guide for Rough Country 1.25 inch Body Lift Kit w/o Shocks (07-15 Wrangler JK 4 Door) Item # J10048 Option B; Manual
Installation Guide for Rough Country 1.25 inch Body Lift Kit w/o Shocks (07-15 Wrangler JK 4 Door) Item # J10048 Option B; Manual Installation Time: 3 Hours Tools Required: Jack (Tall enough to reach body
More informationFord Raptor Venom Front Bumper Installation Instructions
PREPARATION 2010 2014 Ford Raptor Venom Front Bumper Installation Instructions 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake. 2. We recommend
More informationINSTALL INSTRUCTIONS
Jeep JK Rear Corner Skins Product : JK200,JK201,JK202,JK203 Applica on : 2007+ Jeep Wrangler JK ( 2 Door and 4 Door ) Page ( 1 of 6 ) I WARNING Read the instruc ons completely before beginning installa
More informationToyota FJ Cruiser 2006-Up Set Part # Revision A
Toyota FJ Cruiser 2006-Up Set Part # 31924 Revision A 03-31-08 Step 1: Prior to Installation: A) Fit: Verify the fit of the flares to vehicle. (Some filing, sanding, or cutting may be necessary to ensure
More informationTHIS KIT INCLUDES: 8 M8-1.25X40MM BOLTS WITH WASHERS 8 M8-1.25X30MM BOLTS WITH WASHERS RIGHT AND LEFT HINGE
Sal es@lambodoorscanada. com 2407A Kal adarave,ottawa,on K1V 8B9 THIS KIT INCLUDES: 8 M8-1.25X40MM BOLTS WITH WASHERS 8 M8-1.25X30MM BOLTS WITH WASHERS RIGHT AND LEFT HINGE 2 SHOCKS 565 PSI 2 SHOULDER
More informationCORVETTE CORVETTE REV: Made in USA U.S. PATENT #6,808,223; #6,845,547; #7,140,075; #7,059,655 and other patents pending.
CORVETTE 2005-2006 CORVETTE 2005-2007 REV: 7-2-07 Made in USA U.S. PATENT #6,808,223; #6,845,547; #7,140,075; #7,059,655 and other patents pending. Page 1 of 12 CORVETTE C6 2005-2007 THIS KIT INCLUDES:
More informationDriver/Left Top. Support Bracket
PARTS LIST: 1 Grille Guard 8 10mm Lock Washers 1 Driver/Left Frame Bracket 8 10mm Hex Nuts 1 Passenger/Right Frame Bracket 2 8-1.25mm x 25mm Button Head Bolts 1 Driver/Left Bottom Support Bracket 2 8mm
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD RAM 1500 PART # 5058/5058-2
INSTALLATION INSTRUCTIONS GRILLE GUARD PART # 5058/5058-2 PARTS LIST: Qty Description Qty Description 1 Grille Guard 8 12-1.75mm x 35mm Hex Bolts 2 Upper Frame Mounting s (for trucks without tow hooks
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 30914 UNDER SPOILER 2006 TL Issue Date SEP 2005 PARTS LIST Front under spoiler Template B Left bracket (Marked L) Left cover (Marked
More informationFord F150 Front Bumper
2009-2011 Ford F150 Front Bumper Warning! Read the instructions completely before beginning the installation. Before tightening bolts, drilling or cutting where required, check to make sure that there
More informationJK Rear Crusher Flares
INSTALLATION INSTRUCTIONS INST-17-05-010_A JK Rear Crusher Flares IMPORTANT: Thank you for purchasing this Poison Spyder product. Please read through this entire document before proceeding with installation.
More informationInstall. instructions. B8 A4/S4 RS4 Blackout Mesh Style Grille. By: 7716 Wiles Rd.Coral Springs, FL
Install instructions B8 A4/S4 RS4 Blackout Mesh Style Grille By: Preface: The best fitting grille on the market! Completely change the look of your Audi A4 or S4. This mesh style grille features a black
More informationSIGNATURE FRONT BUMPER INSTALL
SIGNATURE FRONT BUMPER INSTALL JL **PLEASE READ THROUGH THE INSTRUCTIONS BEFORE BEGINNING ANY PART OF THE INSTALLATION PROCESS** 1. You can now remove the trim strip (2 vertical clips, 4 horizontal, 2
More informationChevy Colorado. INSTALLATION GUIDE Front Bumper
Chevy Colorado INSTALLATION GUIDE Front Bumper FIG 1A First, we ll start by removing the small allen bolts from the inside fender wells that hold the stock front bumper in place. FIG 1B You will also need
More informationJK Front Crusher Flares
INSTALLATION INSTRUCTIONS INST-17-03-030_A JK Front Crusher Flares IMPORTANT: Thank you for purchasing this Poison Spyder product. Please read through this entire document before proceeding with installation.
More informationPage 1 of 12 GENERAL INSTRUCTIONS KHJKK Installation
Page 1 of 12 KHJKK PICTURE ABOVE IS THE UNIVERSAL KIT; YOUR KIT MAY BE DIFFERENT. THIS KIT INCLUDES: 8 M8-1.25X30MM BOLTS WITH WASHERS 8 M8-1.25X40MM BOLTS WITH WASHERS 2 PINS RIGHT AND LEFT HINGE ASSEMBLY
More informationSAFETY. Read and understand all safety precautions and instructions before installing this product.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationINSTALLATION INSTRUCTIONS DODGE RAM 2 & 4WD 1500 PART # P5058
INSTALLATION INSTRUCTIONS 2009-13 DODGE RAM 2 & 4WD 1500 PART # P5058 PARTS LIST: Qty Description Qty Description 1 Grille Guard 12 12-1.75mm Hex Nuts 2 Upper Frame Mounting s (for trucks without tow hooks
More informationINSTALLATION INSTRUCTIONS 3"/4 BENT END SIDEBARS FORD F-150 SUPERCREW PART # DZ /DZ
INSTALLATION INSTRUCTIONS 09-12 FORD F-150 SUPERCREW PART # DZ 372697/DZ 372699 PARTS LIST: 1 Driver/Left Sidebar 4 1/2 Lock Washers 1 Sidebar 4 12mm x 32mm OD x 3mm Flat Washers 1 Driver/Left Mounting
More informationIncluded in Hardware Kit 2. FLAT STYLE FENDER FLARE. Jeep Wrangler YJ. Set Part # Rev STEP 1 PRIOR TO INSTALLATION
Jeep Wrangler YJ Set Part #10924-07 Rev-0 05-05-11 A) B) C) D) E) STEP 1 PRIOR TO INSTALLATION Bushwacker only approves installing the fl ares according to these written instructions with the hardware
More informationTYGER GUARD. Parts List BEFORE INSTALLATION WARNING TG-GD6D /7. Tyger Guard. Tube Brackets (Bull Bar) passenger or driver side
TYGER GUARD TM BEFORE INSTALLATION TG-GD6D60068 READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED. CUTTING IS
More informationJeep. Flat Style Fender Flares Set of 4. Included in Hardware Kit: STEP 1 PRIOR TO INSTALLATION. Set Part # Rev-3 1/11/2016
STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions
More informationframe bracket Dodge x 2 & 4 x 4 (6-1/2 & 8 Boxes Includes Mega Cab)
, Rev 4 02/19 frame bracket 8552026 Dodge 3500 4 x 2 & 4 x 4 (6-1/2 & 8 Boxes Includes Mega Cab) 14 5 7 2 4 11 9 10 17 3 6 1 8 13 15 16 18 12 ITEM PART # DESCRIPTION QTY. 1 00085.50 FLAT WASHER 10 2 00248
More informationJK Brawler Rockers. *Includes ONE of the Hardware Kits (not both)
INSTALLATION INSTRUCTIONS INST-17-08-200_A JK Brawler Rockers IMPORTANT: Thank you for purchasing this Poison Spyder product. Please read through this entire document before proceeding with installation.
More informationIncluded in Hardware Kit: Jeep Pocket Style Fender Flare Set of 4. Set Part # Rev-0 3/15/2013 TOOLS FOR EASY INSTALLATION:
STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions
More informationCUT OUT FLARES INSTALLATION INSTRUCTIONS FOR 20017, 20018, F100-F150 F250-F350 P.U. & BRONCO CUT OUTS
20017 04/22/03 REV-A CUT OUT FLARES INSTALLATION INSTRUCTIONS FOR 20017, 20018, F100-F150 F250-F350 P.U. & BRONCO CUT OUTS Tools Required for Installation: (A) 3/16 Drill Bit (B) Pop-Rivet Gun (C) Air
More informationIncluded in Hardware Kit: Pocket Style Extended Coverage Fender Flares Front Pair. Jeep
Jeep Pocket Style Extended Coverage Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided.
More informationRough Country JK Modular Winch Mount Bumper With Light End Caps
Rough Country JK Modular Winch Mount Bumper With Light End Caps Note: These instructions involve cutting parts of your vehicle. Please read all instructions prior to starting. Note: This installation also
More information5/16 Hex Head Bolt, 16 pcs. Plastic Push Retainer, 6 pcs. Alcohol Wipe, 2 pcs. Side Refl ex Reflector, 2 pcs
STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions
More information4-Door Rear XHD Armor Fenders
Page 1/10 Part #11615.02 Page 2/10 1 4 2 3 5 Components 1. Left Rear Fender (1) 2. Right Rear Fender (1) 3. Left Rear Guard (1) 4. Right Rear Guard (1) 5. License Plate Bracket (1) OMIX-ADA TECHNICAL SUPPORT
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationINSTALLATION INSTRUCTIONS 3 BULL BAR 99-04, 04 "HERITAGE" F-150/250LD 2WD, 97-04, 04 "HERITAGE" 4WD WD EXPEDITION/ WD EXPEDITION PART
INSTALLATION INSTRUCTIONS 3 BULL BAR PART #B-F1971;B-F2971 PARTS LIST: 1 Bull Bar 2 12-1.75mm x 130mm x 40mm Hex Bolts 1 Driver/Left Mounting Bracket 4 12-1.75mm x 35mm Hex Bolts 1 Passenger/Right Mounting
More informationJeep. Flat Style Fender Flares Front Pair. Included in Hardware Kit:
Jeep Flat Style Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationIncluded in Hardware Kit. Jeep Cut-Out Fender Flare Set of 4 Set Part # Rev STEP 1 PRIOR TO INSTALLATION
Jeep Cut-Out Fender Flare Set of 4 Set Part #10926-07 Rev-01 09-11-12 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the flares according to these written instructions with the hardware
More informationFig A 2. Using a 10mm Socket, remove the two bolts referenced in (Fig B). Save these bolts for reuse. Fig B ADDICTIVE DESERT DESIGNS.
Preparation: Disconnect the negative battery terminal. Park the vehicle on level ground and set the emergency brake. We recommend reading through the installation instructions in whole before performing
More informationJeep Wrangler JK Door Rear Pair Part # Revision E
Jeep Wrangler JK 2007 4-Door Rear Pair Part # 10044 Revision E 03-25-09 Step 1: Prior to Installation: A) Bushwacker only approves installing the flares according to these written instructions with the
More informationJK FRONT DAGGER FRAME CHOP BUMPER INSTALLATION INSTRUCTIONS
JK FRONT DAGGER FRAME CHOP BUMPER INSTALLATION INSTRUCTIONS TOOLS NEEDED 18mm socket or wrench Paint marker 10mm wrench & socket Tape measure Sawzall, or die grinder 15mm socket HARDWARE 4-1/2 X 5.5 Grade
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. 2003 ACCORD AII 24040 4-DOOR CARGO NET P/N 08L96-SDA-100 Issue Date AUG 2002 PARTS LIST Cargo net 2 Anchors TOOLS AND SUPPLIES REQUIRED
More informationChevrolet Cut-Out Fender Flares Set of 4
Chevrolet Cut-Out Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationTOOLS REQUIRED FOR INSTALLATION: AIR RACHET, GRINDER AND CUTTER.
THIS KIT INCLUDES: 16 M8-1.25X30MM BOLTS WITH WASHERS 2 SHOCKS 565 PSI RIGHT AND LEFT HINGE ASSEMBLY 2 SHOULDER BOLTS 2 PINS TOOLS REQUIRED FOR INSTALLATION: AIR RACHET, GRINDER AND CUTTER. 7/23, 10MM,
More informationBefore returning this product to the store of purchase
Before returning this product to the store of purchase Contact Dee Zee if you experience the following problems: Missing Parts Installation Problems/Questions Warranty Questions 1.800.779.2102 Hours of
More informationTrailer Receiver Hitch Installation Instructions
Model/Application: 1006: 10-15 R60 Countryman 10-15 R60 Countryman S 11-xx R61 Paceman 11-xx R61 Paceman S Hitch Capacity: 2000 lbs gross, 200 lb. max tongue Notes: This hitch allows for a removable ball
More information1/4 Rubber Spacer, 26 pcs. M5-.8 Machine Screw, 26 pcs 13. Female Wire Connector, 4 pcs
97-06 Jeep Wrangler TJ Set Part #10920-07 Rev-3 12-15-08 A) B) C) D) E) F) G) STEP 1 - PRIOR TO INSTALLATION Bushwacker only approves installing the fl ares according to these written instructions with
More informationIMPORTANT: PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE
IMPORTANT: PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE 005-07 Cadillac STS Classic 3D Z, Classic Dual Weave, Classic Mesh & Classic Black Mesh Grilles B 7 HR 3 STS Classic 3D Z Grille Part
More information2015 Current GMC Canyon HoneyBadger Front Bumper Installation Instructions
2015 Current GMC Canyon HoneyBadger Front Bumper Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake.
More informationPage 1 of 5 Instructions for Fitting Lower Grille to S Type Jaguar. Part Code 9048
Page 1 of 5 Instructions for Fitting Lower Grille to S Type Jaguar. Part Code 9048 To fit this grille you will need: Torch, 10mm spanner, 10mm socket with extension, T30 torx bits, Screwdrivers, Pliers,
More informationJEEP XJ CRUSADER ROCK SLIDERS INSTALL INSTRUCTIONS
JEEP XJ CRUSADER ROCK SLIDERS INSTALL INSTRUCTIONS Please read the mounting instructions below carefully before attempting to install. Thank you for purchasing your new armor from JcrOffroad! Checkout
More informationRBP-1215B-RX DODGE RAM QUAD CAB RX3
RBP-1215B-RX3 2002-2017 DODGE RAM 15-3500 QUAD CAB RX3 Passenger side RX-3 Side Step Drill Template Passenger side rear Modular Bracket (6) L Support Brackets Driver side rear Modular Bracket Driver side
More informationVIEWPOINT ALUMINUM RUNNING BOARD TOYOTA RAV4
PARTS LIST: VIEWPOINT ALUMINUM RUNNING BOARD 1 Driver/Left Running Board 4 10-1.5mm x 50mm T-Bolt 1 Passenger/Right Running Board 12 10mm Plastic Retainers 1 Driver/Left Bracket 2 10-1.50mm x 40mm Hex
More informationGRILLE GUARD SPRINTER VAN (EXCLUDES X4) INCLUDES MERCEDES, FREIGHTLINER AND DODGE PARTS LIST:
PARTS LIST: 1 Grille Guard 8 12mm Hex Nuts 1 Driver/Left Side Frame Mounting Bracket 2 10-1.50mm x 25mm Button Head Bolts 1 Passenger/Right Side Frame Mounting Bracket 4 10mm x 20mm OD x 2mm Flat Washers
More informationIncluded in Hardware Kit: Jeep. Pocket Style Extended Coverage Fender Flares Front Pair
STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions
More informationRugged Ridge Engine Transmission Skid Plate JK
Installation Time: 1-2 Hours Tools Required: Rugged Ridge Engine Transmission Skid Plate 2012-2017 JK Sockets: 16mm, 17mm, 18mm deep well Socket Wrench Wrenches: 16mm, 18mm Torque Wrench Drill ½ Drill
More informationRedRock 4x4 Rock Crawler Rear Bumper w/tire Carrier - Textured Black (87-06 Wrangler YJ & TJ)
RedRock 4x4 Rock Crawler Rear Bumper w/tire Carrier - Textured Black (87-06 Wrangler YJ & TJ) Installation Time: 3+ Hours Tools Required: Ratchet 18 mm Socket and Wrench 17 mm Socket and Wrench 16 mm Socket
More informationJeep. Flat Style Fender Flares Front Pair Front Part # Rev-9 02/23/2016 For complete fitment info visit :
STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD CHEVY TAHOE / AVALANCHE 1500/ SUBURBAN 1500 PART # /502795
(W) INSTALLATION INSTRUCTIONS GRILLE GUARD PART # 502794/502795 PARTS LIST: 1 Grille Guard 2 12-1.75mm x 140mm Hex Bolts 2 Frame Mounting Brackets 8 12-1.75mm x 30mm Hex Bolts 2 Lower Support Brackets
More informationCut-Out Fender Flares Rear Pair. Jeep. Included in Hardware Kit:
Jeep Cut-Out Fender Flares Rear Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationConflicts. TOYOTA Highlander 2015 Fender Flares Part Number: Accessory Code: BF7000. Safety Tools Safety Glasses
Highlander 2015 Fender Flares Part Number: 00016-48016 Accessory Code: BF7000 Conflicts Note: Factory Splash Guards Kit Contents Item # Quantity Reqd. Description 1 1 Left Front Fender Flare 2 1 Right
More informationJeep. Flat Style Fender Flares Set of 4. Included in Hardware Kit:
STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions
More informationBX2520 Installation Instructions 2004 Mazda 3
BX2520 Installation Instructions 2004 Mazda 3 Serial No. The headlight assembly, front fascia, horn bracket and windshield washer reservoir are removed for baseplate installation. Drilling is required.
More informationInstallation Instructions Kit, Base Rail Bracket Part # 31413
Installation Instructions Kit, Base Rail Bracket Part # 31413 Dealer / Installer: Provide a copy of these Instructions to the end user of this product. These Instructions provide important operating and
More informationIncluded in Hardware Kit 2. FLAT STYLE FENDER FLARE. Jeep Wrangler YJ Fronts. Set Part # Rev STEP 1 PRIOR TO INSTALLATION
Jeep Wrangler YJ Fronts Set Part #10067-07 Rev-0 05-05-11 A) B) C) D) E) STEP 1 PRIOR TO INSTALLATION Bushwacker only approves installing the fl ares according to these written instructions with the hardware
More informationChevrolet Cut-Out Fender Flares Front Pair
STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS SNYPER TUBULAR FENDERS APPLICATION: 2007-2017 Jeep Wrangler JK PART NUMBER: 62-1005, 62-1015 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1,2 2 FRONT FENDERS, DRIVER (1) AND PASSENGER
More informationJK REAR MAULER BUMPER INSTALLATION INSTRUCTIONS
JK REAR MAULER BUMPER INSTALLATION INSTRUCTIONS TOOLS NEEDED 7/16" wrench or socket 3/4" wrench or socket 15/16" wrench or socket 17mm wrench or socket 16 mm wrench or socket 1/2" drill Sawzall or angle
More informationINSTALLATION INSTRUCTIONS FOR & Chevy CUT OUT FLARE
40009 7/10/03 REV-A INSTALLATION INSTRUCTIONS FOR 40009 & 40010 Chevy CUT OUT FLARE TOOLS REQUIRED FOR INSTALLATION: Drill Motor Pop Rivet Gun Flat File Hair Dryer or Heat Gun Sawzall Jack and Jack Stands
More informationChevrolet Cut-Out Fender Flares Set of 4
Chevrolet Cut-Out Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationPlastic Push. 5/16 Hex Head Bolt, 20 pcs. Retainer, 20 pcs. Female Bullet Connector, 4 pcs. Side Refl ex Refl ector, 2 pcs
A) B) C) D) E) F) G) STEP 1 - PRIOR TO INSTALLATION Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according
More informationJK JEEP MIDWIDTH FRONT BUMPER
SIGNATURE SERIES JK JEEP MIDWIDTH FRONT BUMPER INSTALLATION INSTRUCTIONS **PLEASE READ THROUGH THE INSTRUCTIONS BEFORE BEGINNING ANY PART OF THE INSTALLATION PROCESS** 1. Begin the installation of your
More informationFACTORY CAT TOMCAT CORPORATION
FACTORY CAT RPS TOMCAT CORPORATION Artificial Turf and Carpet Sweeping Install Kit #349-641 & #349-642 1. Detach batteries so that there is no power running through the machine before starting. 2. Start
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationPROVEN WORLDWIDE SNORKEL FOR CHEVY COLORADO NEW PRODUCT
AEV30272AC Last Updated: 10/09/18 PROVEN WORLDWIDE SNORKEL FOR CHEVY COLORADO NEW PRODUCT Please visit www.aev-conversions.com to view the most current installation guide for this product. This is a new
More informationChevrolet Cut-Out Fender Flares Front Pair
Chevrolet Cut-Out Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationImportant Note. Tools Required: Welder capable of fully welding 10 GA.135 steel
INSTALLATION INSTRUCTIONS Frame Reinforcement Kit 11102 (Patent Pending) 1964-67 GM A-Body Coupe/2dr Sedan Read Instructions FULLY before starting Installation Important Note Installation of this kit requires
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory WELL P/N 08P21-STX-200A Application 2011 MDX Publications No. BII 43668 Issue Date AUG 2010 PARTS LIST Left front fender trim Bracket A-L Left front bumper trim Bracket
More informationAll Terrain Flares 2014 Chevy Silverado
Page 1/8 Components: 1. Front Flares (2) 2. Rear Flares (2) Tools required: - Utility knife - #2 Phillips driver - Socket wrench - 13 mm Socket - 6 mm Allen Wrench - T-15 Torx bit - Trim Removal Tool -
More informationJeep. Cut-Out Fender Flares Set of 4. Included in Hardware Kit: Set Part # Rev-8 06/29/16 STEP 1 PRIOR TO INSTALLATION
STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the flares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions
More information4 DOOR JK ROCK SLIDERS INSTALLATION
SIGNATURE SERIES 4 DOOR JK ROCK SLIDERS INSTALLATION 1. To remove either the Jeep JK Wrangler Unlimited Rubicon rocker guards or Sahara running boards, use a 10mm wrench to remove the 3 pairs of nuts securing
More informationChevrolet Cut-Out Fender Flares Set of 4
Chevrolet Cut-Out Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationAll Terrain Flares 09+ Ford F150
Page 1/5 Components: 1. Front Flares (2) 2. Front Flare Inner Pieces (2) 3. Rear Flares (2) Tools required: - Utility knife - Electric Drill - 1/4 Drill Bit - #2 Phillips driver - Socket wrench Hardware
More informationGMC Cut-Out Fender Flares Front Pair
STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions
More informationInstall. Jeep JK Adventure Tire Carrier. Tools Needed. Hardware
Jeep JK Adventure Tire Carrier Thank you for purchasing the Adventure upper tire carrier from JcrOffroad! Checkout our website, www.jcroffroad.com for more deals and other great off road products. Please
More information4 DOOR JK ROCK SLIDERS INSTALLATION
SIGNATURE SERIES 4 DOOR JK ROCK SLIDERS INSTALLATION 1. To remove either the Jeep JK Wrangler Unlimited Rubicon rocker guards or Sahara running boards, use a 10mm wrench to remove the 3 pairs of nuts securing
More information8030 Synergy Jeep JK Rear Long Arm Frame Brackets
General Notes: SYNERGY MFG. 870 INDUSTRIAL WAY, SAN LUIS OBISPO, CA (805) 242-0397 8030 Synergy Jeep JK Rear Long Arm Frame Brackets These instructions are also available on our website; www.synergymfg.com.
More informationPart # 4463 & Ford Mustang C-Series Upper & Lower Grilles
Rev. 3/18 Page 1 Part # 4463 & 4464 2018 Ford Mustang C-Series Upper & Lower Grilles Notice: Install new, parts according to these instructions! Altered Parts are Non-Refundable! Part #4464 Notice: Part
More informationOTHER TOOLS MAY BE NEEDED DEPENDING ON YOUR VEHICLE.
THIS KIT INCLUDES: 16 M8-1.25X40MM BOLTS WITH WASHERS 2 SHOCKS 720 PSI RIGHT AND LEFT HINGE ASSEMBLY 2 SHOULDER BOLTS 2 PINS TOOLS REQUIRED FOR INSTALLATION: AIR RACHET, GRINDER AND CUTTER. 10MM, 11MM,
More informationINSTALLATION INSTRUCTIONS 6 OVAL BENT END SIDEBARS DODGE RAM 1500, CREW CAB PART#: /241533B
PARTS LIST: 1 Driver/Left Sidebar 24 8mm x 24mm x 2mm Flat Washers 1 Passenger/Right Sidebar 12 8mm Lock Washers 3 Driver/left, Passenger Center and Rear 6 8mm Hex Nuts 3 INSTALLATION INSTRUCTIONS 6 OVAL
More informationWARNING!! DO NOT LIFT DOORS UP WHEN THE HOOD IS OPEN. THE DOORS WILL HIT THE HOOD!
WARNING!! DO NOT LIFT DOORS UP WHEN THE HOOD IS OPEN. THE DOORS WILL HIT THE HOOD! THIS KIT INCLUDES: 4 M8-1.25X30MM BOLTS WITH WASHERS 12 M8-1.25X40MM BOLTS WITH WASHERS 2 SHOULDER BOLTS WITH RIGHT AND
More informationFlat Style Fender Flares Front Pair. Jeep. Included in Hardware Kit:
Jeep Flat Style Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationINSTALLATION INSTRUCTIONS
Do not attempt to install this product on any vehicle other than the one it is designed for and listed above! Parts List 10 3/8 X 1 1/4 Hex Bolt 10 3/8 Lock Washer 4 3/8 Hex Nut 4 3/8 Flat Washer 2 3169)
More informationCORVETTE Page 1 of 12 CORVETTE C
CORVETTE 2005-2006 Page 1 of 12 CORVETTE C5 1997-2004 THIS KIT INCLUDES: 8 M8-1.25X40MM BOLTS WITH WASHERS 8 M8-1.25X30MM BOLTS WITH WASHERS RIGHT AND LEFT HINGE ASSEMBLY WIRE LOOM 2 SHOCKS 565 PSI 2 SHOULDER
More information