HEADLIGHT CONNECTOR REPLACEMENT
|
|
- Emma Alexander
- 5 years ago
- Views:
Transcription
1 Classification: Reference: Date: EL01-006a ITB01-021a October 17, 2003 HEADLIGHT CONNECTOR REPLACEMENT IMPORTANT: THIS BULLETIN HAS BEEN REVISED. The Service Procedure was updated with new information about wire end-to-end splicing. The Claims Information section was revised with a new SYM and DIA code. Please use this bulletin ITB01-021a for complete information. Discard all previously distributed copies of ITB APPLIED VEHICLES: All Infiniti except vehicles equipped with xenon headlights SERVICE INFORMATION Infiniti has established replacement headlight connectors and service procedures to replace damaged connectors on the applied vehicles. If the headlight wire harness connector is damaged, causing intermittent or improper headlight operation, or the connector otherwise needs replacement, follow the procedures in this bulletin. Refer to the Diagnosis/Repair Flow Chart on page two to diagnose and resolve this incident, should it occur. 1/6
2 Diagnosis/Repair Flow Chart Confirm the incident exists. Disconnect the incident headlight wire harness connector and inspect it for damage or deformation. Is the connector damaged or deformed? No Look for other causes of the incident (i.e., bad headlight bulb*, wire harness short or open circuit, etc.). * ONLY use genuine Nissan replacement headlight bulbs. Yes Replace the headlight wire harness connector with the new one listed in the Parts Information section. Refer to the "Headlight Wire Harness Connector Replacement Procedure" on page 3. Install a new genuine Nissan replacement headlight bulb. Ensure there is NO interference between the repaired headlight harness and surrounding components. Disconnect the other headlight wire harness connector and inspect it for damage or deformation. Is the connector damaged or deformed? No Replace the bulb with a genuine Nissan replacement headlight bulb. Yes Replace the headlight wire harness connector with the new one listed in the Parts Information section. Refer to the "Headlight Wire Harness Connector Replacement Procedure" on page 3. Install a new genuine Nissan replacement headlight bulb. Ensure there is NO interference between the repaired headlight harness and surrounding components. Complete. 2/6
3 SERVICE PROCEDURE Headlight Wire Harness Connector Replacement Procedure IMPORTANT: Each wire connection joint MUST be joined and sealed with the Essential Tool Flameless Heat Gun J and Solder Sleeve Connectors J due to the high wire current and moisture in this location. DO NOT use Scotch-Loks, butt connectors, or soldering/heat shrink tubing for splicing at this location. 1. Disconnect the vehicle-side wire harness connector from the headlight bulb. 2. Cut the vehicle wire harness about an inch back from the headlight harness connector. 3. Cut the wires of the replacement connector to the appropriate length. NOTE: Perform the following steps on ONE wire (joint) connection at a time. 4. Use essential Wire Crimping/Stripping Tool #J (or equivalent) to strip off about 10mm of insulation from the ends of the wires (on the vehicle wire harness side and on the replacement connector wires). See Figure 1. Then, firmly twist the exposed wire strands (on each wire). NOTE: Use the correct size opening in the Wire Crimping/Stripping Tool so you won t cut off any strands of wire. Less strands reduces the ability of the wire to handle the expected electrical load. Wire Wire Crimping/ Stripping Tool J (or equivalent) Figure 1 TP Slide the appropriate size Solder Sleeve Connector over one of the wires (see Figure 2). Solder Sleeve Connector Stripped Wire Figure 2 TP /6
4 6. Connect the wire (of the replacement connector) to the vehicle wire harness making sure the wires are correctly connected (i.e., no mis-matched wires). Then, firmly and securely twist the two wire ends together (see Figure 3). Wires Twisted Wires Figure 3 TP Now slide the Solder Sleeve Connector over so that the solder ring is centered around the exposed twisted wire area (see Figure 4). Exposed Twisted Wires Adhesive Ring Adhesive Ring Solder Ring Solder Sleeve Connector Figure 4 TP /6
5 8. Use the FlameLess Heat Gun to heat the Solder Sleeve connector (see Figure 5). This operation will: Melt the solder (silver ring inside solder connector) into the exposed twisted wire area (see Figure 6) Solder Sleeve Connector Wire Melt the sealant (colored rings inside solder connector) onto the wires (see Figure 6) Shrink the plastic sleeve onto the wires WARNING: The Flame-Less Heat Gun and the Solder Sleeve Connector become HOT during the soldering process. Allow the Gun and connectors to cool down before handling them. Flame-Less Heat Gun Figure 5 TP F Important Soldering Tips: Position the Solder Sleeve Connector in the middle of the heat shield (of the Heat Gun). Start heating the connector from the center and move back and forth (side to side) and around to allow even distribution of the heat to the entire connector. Melted Solder Wire Solder Sleeve Connector Make sure the solder completely flows into the exposed twisted wires and the adhesive properly seals the wire insulation to the connector sleeve. Remove the heat immediately after this happens. CAUTION: Be careful not to damage the connector or wires with the heat gun: Do NOT apply heat for more than about 40 seconds. Do NOT overheat the connector or wires (i.e., severe darkening of connector sleeve or wire insulation). Figure 6 Melted Adhesive (Colored Rings) TP030544a 5/6
6 PARTS INFORMATION DESCRIPTION PART NUMBER QUANTITY 3-Pin Headlight Wiring Harness Connector* B4343-0UFB0 Up to 2 2-Pin Headlight Wiring Harness Connector* B4342-0UFB1 Up to 2 3-Pin Headlight Wiring Harness Connector* B4343-0QFB1 Up to 2 * See Figure 7 below for connector type differences. HEADLIGHT CONNECTOR TYPES 3-Pin, P/N B4343-0UFB0 2-Pin, P/N B4342-0UFB1 3-Pin, P/N B4343-0QFB1 TP Figure 7 CLAIMS INFORMATION Submit a Primary Failed Part (PP) line claim using the following claims coding: DESCRIPTION PFP OP CODE SYM DIA FRT Repair Wiring Harness (1) RA16AA HE 63 S/T (2) (1) Reference the Parts Information table above and use the indicated harness P/N as the PFP. (2) Straight time operation use actual time required to replace terminal. Suggested FRTs, for most vehicles, are 0.3 hrs. for one side or 0.4 hrs. for both sides. 6/6
ELECTRICAL WIRING SOLDERING AND CRIMPING Article No. REPAIRS SERVICE TIPS
ELECTRICAL WIRING SOLDERING AND CRIMPING Article No. REPAIRS SERVICE TIPS 03-11-6 FORD: LINCOLN: MERCURY: 1997 PROBE, THUNDERBIRD 1997-2000 CONTOUR 1997-2002 ESCORT 1997-2003 CROWN VICTORIA, MUSTANG, TAURUS
More informationG35; NAVI DISPLAY UNIT WILL NOT RISE / LOWER / STAY UP
Classification: Reference: Date: EL07-004 ITB07-021 May 24, 2007 2005-2006 G35; NAVI DISPLAY UNIT WILL NOT RISE / LOWER / STAY UP APPLIED VEHICLE: 2005-2006 G35 (V35) APPLIED VIN(S): Vehicles built before:
More informationElectrical - Wiring Soldering/Crimping Service Tips
TSB 05-18-7 09/22/05 22 septembre 2005 - Wiring Soldering and Crimping Repairs - Service Tips WIRING SOLDERING AND CRIMPING REPAIRS FORD: 2000-2006 Crown Victoria, Focus, Mustang, Taurus 2002-2005 Thunderbird
More informationService Bulletin Terminal Replacement Instructions (Replaces , dated May 2, 1995) December 18, 2000 ALL
Service Bulletin 00-039 Applies To: ALL December 18, 2000 Terminal Replacement Instructions (Replaces 95-007, dated May 2, 1995) These terminal replacement instructions apply to these kits and tools: Terminal
More informationField Installed Connectors for TraceTek 7000-HUV Bulk Cable Installation Instructions
TraceTek TT-7000-HUV-CK-MC-M/F Field Installed Connectors for TraceTek 7000-HUV Bulk Cable Installation Instructions Description These instructions describe field connecting of TT7000-HUV Bulk Sensing
More informationTerminal Replacement Procedures
HOW TO REPLACE CONNECTOR TERMINALS The terminal repair kits provide necessary tools and materials (terminals, wire seals, and splice connectors) to repair many damaged or faulty connector terminals. However,
More information1. General Repair Methods
28 Van Trailer Harness System REPAIR HARNESS REPAIR METHODS SECTION OBJECTIVES 1. General Repair Methods 2. Splicing New Wire 3. Stripping & Crimping Basics 4. Sealing New Wire 1. General Repair Methods
More informationG37 CONVERTIBLE; SQUEAK / RATTLE / BUZZ NOISE FROM ROOF AREA
Classification: Reference: Date: BT11-031 ITB12-003 January 13, 2012 2009-2011 G37 CONVERTIBLE; SQUEAK / RATTLE / BUZZ NOISE FROM ROOF AREA This bulletin supersedes ITB10-071. Discard all copies of ITB10-071.
More informationRTD-Style Special e.dot Hot Melt Hoses
User s Guide P/N 1081164A 02 RTD-Style Special e.dot Hot Melt Hoses Safety WARNING: System pressurized! Relieve system hydraulic pressure before breaking any hydraulic connection or seal. Failure to relieve
More informationS e r v i c e B u l l e t i n # doc
S e r v i c e B u l l e t i n #910159.doc Clearlake Byron Lynden Page 1 of 11 FINAL ASSY/MODEL 330/334 MERGER Title: 330/334 CONTROL BOX DIODES Approval Initials Date Approval Initials Date Author MTL
More information(WD) Dodge Durango (WK) Jeep Grand Cherokee
Dealer Service Instructions for: Safety Recall R09 / NHTSA 15V-115 Fuel Pump Relay Models 2012-2013 (WD) Dodge Durango (WK) Jeep Grand Cherokee July 2015 IMPORTANT: Many of the vehicles within the above
More informationunit 3: GENErAL ElectriCAL SySTEM DiAGNOSiS
Electrical/Electronic Systems unit 3: GENErAL ElectriCAL SySTEM DiAGNOSiS lesson 4: wire and connector repairs I. Connector repairs A. Connector repairs involve fixing damaged wires. Wires are marred due
More informationWiring Repair WIRING REPAIR
20-10-00 Wiring Repair WIRING REPAIR 1. GENERAL This section contains procedures applicable to the fabrication and repair of wire harness assemblies, cables, and wires. All wiring repairs of wire harness
More informationGood Connections PART 2
THE INSTALLER SERIES by Steve Bodofsky Good Connections PART 2 Figure 1: You can improve the quality and longevity of a butt connector by sealing the ends, either with RTV, or by using a connector designed
More informationSKDG Cable Repair Kit Instructions
SKDG Cable Repair Kit Instructions Description Having to repair your EasyHeat cable is an extremely rare occurrence. Damage is almost always a function of field conditions, such as impacts with tools.
More informationVOLUNTARY SERVICE CAMPAIGN WINDOW REGULATOR
Reference: NTB03-118 December 10, 2003 Date: VOLUNTARY SERVICE CAMPAIGN WINDOW REGULATOR CAMPAIGN I.D. #: APPLIED VEHICLES: APPLIED VINs: PU306 & PU307 2001 Altima (L30) 2001-02 ier (D22), crew cab and
More informationTerminating D /-0289 Subminiature SolderTact Contacts to Twisted-Pair Cable
Print 12-Jun-03 1 of 11 Terminating D-602-0288/-0289 Subminiature SolderTact Contacts to Twisted-Pair Cable 1. Purpose and Scope This engineering standard contains the termination procedures, inspection
More informationB Cut the Old Terminal from the Harness. Replace the terminal. 2. Select the correct replacement terminal with lead, from the supply parts.
B 27 Step 3. Existing terminal Replace the terminal. 1. Cut the Old Terminal from the Harness. Use the new wire lead as a guide for proper length. NOTE: If the length of wire removed is not approximately
More informationFRONTIER; MIL ON WITH DTC P0442 / P0455 / P0456 / P1446
Classification: Reference: Date: EC07-007 NTB07-059 September 6, 2007 2005 2007 FRONTIER; MIL ON WITH DTC P0442 / P0455 / P0456 / P1446 APPLIED VEHICLES: 2005 2007 Frontier (D40) IF YOU CONFIRM: A MIL
More informationTermination of D-621 Triaxial Connectors to Shielded Twisted Pair Cable for MIL-STD-1553B Applications
1 of 18 Termination of D-621 Triaxial Connectors to Shielded Twisted Pair Cable for MIL-STD-1553B Applications This Engineering Standard forms a part of Engineering Standard ES-61162: "D-621 Connectors
More informationSOLDER SLEEVES AIRWORTHINESS BULLETIN. Overview. Repair and Maintenance Techniques for Wiring Systems Date : 29 July 2005.
Attachment 2 SOLDER SLEEVES Overview This topic describes the termination and installation procedures for shielded cable on aircraft. Page 35 of 93 Solder Sleeves Shielded cable, in one form or another,
More informationSchluter -DITRA-HEAT Repair procedure for the DHE-HK Heating Cable
Schluter -DITRA-HEAT Repair procedure for the DHE-HK Heating Cable 555758 03/2018 2018 Schluter Systems L.P. DITRA and HEAT E are registered trademarks of Schluter Systems CONTENTS 3 List of tools required
More informationEET 150 Introduction to EET Lab Activity 6 Introduction to Wire Splicing and Soldering
Required Parts, Software and Equipment Parts None for this activity EET 150 Equipment Required Hookup wire (22 AWG) Wire cutter/stripper Soldering Iron* Soldering Iron Stand* Solder (Use standard lead/tin
More information2 Recommended Tools / Supplies
Bias Scout TM Kit Assembly Manual Version 3.1 25 March 2015 1 Inventory of Parts 1 ea octal socket 1 ea octal base, brown (1 3/16" dia x 7/8" high) 1 ea 1.0 / 1W metal oxide, flame proof resistor 1 ea
More informationWire Harness - Terminal Repair Kit
Wire Harness - Terminal Repair Kit Article No. 01-10-12 5/28/01 WIRING - WIRE HARNESS TERMINAL REPAIR KIT AND WIRE SPLICE PROCEDURE FORD: 1985-1994 TEMPO 1985-1997 THUNDERBIRD 1985-2002 CROWN VICTORIA,
More informationMaking The Cut. Assembly of the LED Neon Flex can be done in the shop or in the field.
Making The Cut Assembly of the LED Neon Flex can be done in the shop or in the field. From the spool of LED Neon Flex, count the number of sections you will need for your project. In the 120 volt LED Neon
More information1.0 Receiver TAC Contact Insertion/Extraction. 2.0 TAC (Receiver) Module Installation/Removal. 3.0 Wiring Contact Insertion/Extraction
Downloadable Documents (Adobe Acrobat (TM) format) Click on the links below to view or download copies of VPC User Manual in Adobe Acrobat (.PDF) format. Note: If you would like printed copies of any of
More informationUnderstanding and Making Crimp Connections That Last
Understanding and Making Crimp Connections That Last What are the Basic Process Methods Used to Connect (Terminate) a Wire to Make an Electrical Connection? SOLDER SOLDERLESS WELDED (Ultrasonic Welding)
More informationWater Level Meter: Op Instructions
Equipment Check 1. Turn sensitivity switch fully clockwise. Notes: 1. Clockwise rotation of sensitivity swsitch turns meter on and increases sensitivity. 2. Always set switch to highest sensitivity position,
More informationVS- 3 Hand Tool Kits , , and
VS- 3 Hand Tool Kits 244271-1, 244271-5, and 244271-6 Instruction Sheet 408-7280 Jan 2017 PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools.
More informationELECTRICAL CONNECTIONS
ELECTRICAL CONNECTIONS Lesson 13 EET 150 Electrical Connections Learning Objectives In this lesson you will: see different methods of making electrical connections. learn a procedure for making soldered
More informationHOLLINGSWORTH Operating Instructions
HOLLINGSWORTH Operating Instructions H20 - Rotary Nest Hand Crimping Tool HOLLINGSWORTH (800) 638-8376 techsuppt@hollingsworth.com www.hollingsworth.com OPERATING INSTRUCTIONS FOR HOLLINGSWORTH H20 ROTARY
More informationInstall The Trailer Lighting Wire Harness Connector
Install The Trailer Lighting Wire Harness Connector This is probably the toughest part of the whole trailer hitch install. It helps to have a little background in electronics, but if you don't then simply
More informationRepairing your Porsche 928 Central Warning System (CWS) controller
Repairing your Porsche 928 Central Warning System (CWS) controller Disclaimer: This procedure is for a 1984 Porsche 928 S controller. Overview: Under the left foot pedal (dead pedal) of the Porsche 928
More informationWOT Box Installation Instructions Mazda Speed 3
WOT Box Installation Instructions Mazda Speed 3 Connector Pinout Pin Color AWG Name Description 1 Yellow 18 CKP Connect to Crankshaft Position Sensor 2 Black 18 Ground Connect to chassis ground 3 Black
More informationUPC-LL Power Connection Kit
Installation Instructions UPC-LL Power Connection Kit for Series Long Line Heating Cables 1 PJ951 161-562681-020 July 2015 UPC-LL End Termination Kit Kit Contents Item Qty Description Item Qty Description
More informationApplication Note. Athearn RTR AC4400CW Tsunami Digital Sound Decoder Installation Notes
Application Note Overview This application note describes how to install a TSU-AT1000 Digital Sound Decoder into an HO Athearn Ready To Roll AC4400CW. Skill Level 2: The entire installation can be completed
More informationPOWERPOLE CONNECTORS. Fountain Valley RACES 05 Feb 2008
POWERPOLE CONNECTORS Fountain Valley RACES 05 Feb 2008 ACCESORIES SPLITTER WITH OEM T-CONNECTOR ACCESSORIES RED DEE 2 SPLITTER Any connection point is an input / any connection point is an outlet ACCESSORIES
More informationResist water & condensation Resist salt & other contaminants Resist wire pull out & current leakage
Heat Seal & Resist water & condensation Resist salt & other contaminants Resist wire pull out & current leakage Who Uses Heat Shrink : Heavy Duty Trucking Marine & RV Plant Maintenance Departments OEM
More informationSoldering and Desoldering Instruction
Soldering and Desoldering Instruction Soldering is defined as "the joining of metals by a fusion of alloys which have relatively low melting points". In other words, you use a metal that has a low melting
More informationMOTOR & BULK HEAD. A Manual for Repair and Maintenance Technicians
MOTOR & BULK HEAD A Manual for Repair and Maintenance Technicians CAUTION This manual is designed to help technicians who are already experienced in workshop procedures and know how to handle tools. Only
More informationFILE // 4 GAUGE TERMINAL CONNECTORS DOCUMENT
04 July, 2018 FILE // 4 GAUGE TERMINAL CONNECTORS DOCUMENT Document Filetype: PDF 293 KB 0 FILE // 4 GAUGE TERMINAL CONNECTORS DOCUMENT Alibaba.com offers 124 4 gauge wire connectors products. Unique Bargains
More informationLC31L-BAT Link Coupler
Instruction Manual For the LC31L-BAT Link Coupler 09 March 2018 2012-2018 by Ralph Hartwell Spectrotek Services All rights reserved 2 RADIO FREQUENCY WARNING NOTICE If the LC31L-BAT is installed incorrectly
More informationPOORMANPROPS SEPTEMBER 24 th Make-N-Take
POORMANPROPS SEPTEMBER 24 th Make-N-Take CREEPY CANDLES Based Off http://www.instructables.com/id/pvc-candles/ Tools: Hack saw or miter saw or PVC cutters (that can cut 1 ½ PVC) Hot glue gun Materials:
More informationWhy Use of Anderson Recommended Crimp Tooling is so Important
Why Use of Anderson Recommended Crimp Tooling is so Important Our connectors are designed to achieve the highest levels of durability, reliability, and performance as shown on the connector data sheets.
More informationQSLVM2500 QSLV-M Cold Shrink Insulator
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 QSLVM2500 QSLV-M 2-500 Cold Shrink Insulator Minnesota Mining (3M) Catalog Number Manufacturer Description Weight per
More informationTeam Xecuter Joycon Mod By: XxWiReDxX
Team Xecuter Joycon Mod By: XxWiReDxX Works With Every Switch SX OS Works with every Nintendo Switch and every firmware version! Play Every Game With SX OS you can play all your favorite games straight
More informationGolf Trolley Workshop (Devon)
Golf Trolley Workshop (Devon) Powerpole General Assembly Instructions Assemble the red and black plastic housings together correctly on the first try, they fit snugly and can be difficult to get apart.
More informationSignal converter for electromagnetic flowmeters
Quick Start Signal converter for electromagnetic flowmeters Electronic revision: ER 3.0.xx The documentation is only complete when used in combination with the relevant documentation for the flow sensor.
More informationFull Size Pick Ups - GM Suburban/Yukon/Tahoe - GM Escalade - Cadillac Click on a link tab to jump to that page.
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,1999,2000. Factory Radio Other
More informationI Click on a link tab to jump to that page. Cover Page
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,1999,2000. Factory Radio Other
More informationRTD-Style Hot Melt FoamMix Hoses for Bulk Melter Systems
Nordson Corporation OPERATOR S CARD P/N 1121861_01 RTD-Style Hot Melt FoamMix Hoses for Bulk Melter Systems Safety WARNING! Allow only personnel with appropriate training and experience to operate or service
More informationBushwacker Jeep Flat Style Fender Flares Front Pair
Bushwacker Jeep Flat Style Fender Flares Front Pair Note: These instructions involve cutting parts of your vehicle. Please read all instructions prior to starting. Installation Time: 3-4 Hours Tools Required:
More informationSCOPE Perma-Seal Terminals and Splices AWG (Rings, Spades, Hooks, 3 and 4-Ways, and Splices). RHT-5770 Hand Crimp Tool
Hand Crimp Tool Operating Instruction Sheet and Specifications Part No. 64001-3200 Eng. No. RHT 5770 (Replaces 19285-0050 and 19285-0143) FEATURES A full cycle ratcheting hand tool ensures complete crimps
More informationScaleRCHelis.com V Light Controller Kit
Thank you for purchasing the ScaleRCHelis.com V1.1 450 Light Controller Kit. This is something you can build in under a hour with some simple soldering equipment. Your kit will include all the parts necessary
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions Honda CRV 1997-2003 THE safety accessory of the 21 st Century. P/N 210-0032-0 Rev B2 (6-26-04), GG 2003 Muth Mirror Systems, LLC. Note: Professional Installation
More informationHotEnd. HotEnd docs.imade3d.com/ Page 1 of 19
HotEnd 2018 docs.imade3d.com/ Page 1 of 19 INTRODUCTION JellyBOX uses a genuine E3D-Lite6 HotEnd with our own heat block upgrade for faster and easier printing. Assembly of the hotend should take a quarter
More informationIMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED
IMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED Please Forward All Attached Information to Consumer Warranty Not Valid Unless Returned to Volant Performance STOP Please be sure to review the enclosed
More informationDaytime Running Lights - Splice-in (10-12 All):
Time Necessary: Approximately 1 hour Tools Required: Heat Gun Installation Procedure: Daytime Running Lights - Splice-in (10-12 All): 1. It is recommended that the positive terminal be removed from the
More informationSERVICE BULLETIN ATTN: PARTS AND SERVICE MANAGER. Mandatory Rework: Installation of an In Line Fuse.
SERVICE BULLETIN ATTN: PARTS AND SERVICE MANAGER DATE: April 21, 2014 NUMBER: 14-04 SUBJECT: Kohler DSAI Ignition Module UNITS AFFECTED: SITUATION: SOLUTION: Lazer & Pioneer Models: Kohler-Powered Units
More informationInstallation & Weatherproofing Guide for ENCOM Broadband Radios
Installation & Weatherproofing Guide for ENCOM Broadband Radios Read the following instructions before proceeding with your ENCOM Wireless Radio installation. Keep these instructions in safe location for
More informationVERSION 1.7 PRT-ES USER GUIDE. ZiPPERTUBiNG CO. THE. (480)
VERSION 1.7 PRT-ES USER GUIDE THE ZiPPERTUBiNG CO. www.zippertubing.com (480) 285-3990 R Table of Contents pg.1 TABLE OF CONTENTS Introduction... 2 Installation: Procedure A... 4 Installation: Procedure
More informationOVERVIEW: This bulletin involves installing one of two hinge reinforcement kits based on inspection.
NUMBER: 23-017-02 GROUP: Body DATE: May 20, 2002 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored in
More informationHand Crimp Tool Operating Instruction and Specifications Sheet Part No Eng. No. RHT 5770 (Replaces and )
Hand Crimp Tool Operating Instruction and Specifications Sheet Part No. 64001-3200 Eng. No. RHT 5770 (Replaces 19285-0050 and 19285-0143) FEATURES Œ A full cycle ratcheting hand tool ensures complete crimps
More informationNEO CAR AUDIO. Neo AUXiN AUX INPUT INTERFACE. Instruction Manual
NEO CAR AUDIO Neo AUXiN AUX INPUT INTERFACE Instruction Manual IMPORTANT NOTE Neo AUXiN Dip switch positions MUST be set BEFORE any other step is taken. Otherwise, the kit will not operate properly. See
More informationRam Truck /2500/3500
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws.,1998,1999,2000. Factory Radio Other
More informationTable of Contents. F. High-Current Modules...F-2 PG1 Ground Module...F-2 1. Product Overview...F-2 2. Installation...F-3
Table of Contents F. High-Current Modules...F-2 PG1 Ground Module...F-2 1. Product Overview...F-2 2. Installation...F-3 2.1 Cable Installation...F-3 2.2 Cable Removal...F-5 2.3 Module Installation...F-6
More informationModifying a USB sound fob to act as a repeater interface for app_rpt
Modifying a USB sound fob to act as a repeater interface for app_rpt This document explains how to modify a USB sound fob to work as a repeater interface for app_rpt. The following materials and tools
More informationJUN FEATURE 2014 PRODUCT OF THE
JUN 2014 FEATURE PRODUCT OF THE MONTHPage 1 Tools Self-Igniting Butane Torches Torches / Crimpers / Stripper / Heat Gun Up to 2500 flame temperature Safety lock and continuous burning lock With Piezo ignition,
More informationCover Page. Factory Radio Other Documents Available For This Vehicle:
Factory Radio Other Documents Available For This Vehicle: No documents available at this time Adobe Acrobat Reader Printing Tips: Factory Radio with dash radio installation kit 1) Select FLE then PRNT
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions 2004 2008 Ford F-150 XLT, FX4, & Lariat Pre-wired without side signals Pre-wired with side signals Without side directional lights, see page 2 With side directional
More informationI Click on a link tab to jump to that page. Cover Page
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,1999,2000. & nstall Factory
More informationWhy Use of APP Recommended Crimp Tooling is so Important
Why Use of APP Recommended Crimp Tooling is so Important APP connectors are designed to achieve the highest levels of durability, reliability, and performance as shown on the connector data sheets. Crimp
More informationHigh Current Pin and Socket Contacts 31 JUL 13 Rev C
Application Specification High Current Pin and Socket Contacts 31 JUL 13 NOTE NOTE i All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and
More informationHandling Precaution for Terminal and Connector
1 Handling Precaution for Terminal and Connector Handling Precaution for Terminal and Connector This manual is to describe basic precautions for use of terminal and connector in the following. Make use
More informationSEALED CRIMP CONNECTORSTM
SEALED ELECTRICAL SYSTEM It s a Question of Integrity SEALED CRIMP CONNECTORSTM KRIMPA-SEAL TM PRODUCT LINE SEALED FOR QUALITY MINI ASSORTMENTS NSPA-9002 STARTER ASSORTMENTS TM NSPA-5002 NSPA-5003 NSPA-5003-T
More informationInstructions for Lighting an S Scale Caboose
Instructions for Lighting an S Scale Caboose The S Scale Caboose lighting kit is adaptable for most caboose models of rolling stock including American Flyer (TM) and contains the same components as found
More informationOpenROV. Guide 3 - Electronics. We will now move to the assembly of the electronics that will control the ROV. Written By: OpenROV
OpenROV Guide 3 - Electronics We will now move to the assembly of the electronics that will control the ROV. Written By: OpenROV 2017 openrov.dozuki.com Page 1 of 33 INTRODUCTION We will introduce soldering
More informationDESCRIPTION 3. DIE INSTALLATION AND REMOVAL Die Removal (Figure 3) 3.1. Die Installation (Figure 3) Hydraulic Hand Tool
Crimping Dies Instruction Sheet for SOLISTRAND* 08 869 s and Splices 9 APR PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools
More informationAssembly Instructions for the 1.5 Watt Amplifier Kit
Assembly Instructions for the 1.5 Watt Amplifier Kit 1.) All of the small parts are attached to a sheet of paper indicating both their value and id. 2.) Leave the parts affixed to the paper until you are
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: REAR SPOILER KIT - CARBON FIBER INFINITI Q60 T99J1 5CH0B KIT CONTENTS: Item Qty. Part Description A 1 Spoiler Assembly B 4
More informationInstallation Instructions Road King Classic Saddlebag Bezels
Installation Instructions Road King Classic Saddlebag Bezels Thank you for your purchase of Bagger Audio Road King Classic Saddlebag Bezels for your Harley-Davidson motorcycle. We have carefully engineered
More informationBi-Color Signal Mirror Installation Instructions
Bi-Color Signal Mirror Installation Instructions 2005-2009 Toyota Tacoma THE safety accessory of the 21 st Century. P/N 210-0141-0 Rev. A2 (3/30/09), BTV 2007 Muth Mirror Systems, LLC Page 3 of 13PplPage
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions Ford Explorer 1996-2001, Ford Explorer SportTrac 2001, Ford Ranger 1996-2001, Mazda B-2500\B-3000\B-4000 1998-2001, Mercury Mountaineer 1997-2001 THE safety accessory
More informationCover Page. Factory Radio Other Documents Available For This Vehicle:
Factory Radio Other Documents Available For This Vehicle: No documents available at this time Adobe Acrobat Reader Printing Tips: Factory Radio with dash radio installation kit 1) Select FLE then PRNT
More informationF-Series Trucks - Ford Full Size Bronco - Ford
& nstall Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,1999,2000. Factory
More informationCrimping Dies; PN thru 47825, 47915, and 47918
Crimping Dies; PN 47820 thru 47825, 47915, and 47918 Instruction Sheet 408-1729 22 NOV 16 Rev K Crimping Dies; PN 47820 thru 47825, 47915, and 47918 (Typical) Crimping Die Wire Size Part Number Color Code
More informationBRIDGEABLE FOUR-CHANNEL POWER AMPLIFIER GM-A6604 GM-A4604. Owner s Manual
BRIDGEABLE FOUR-CHANNEL POWER AMPLIFIER GM-A6604 GM-A4604 Owner s Manual Section 01 Before you start Thank you for purchasing this PIONEER product To ensure proper use, please read through this manual
More informationANDERSON POWERPOLE CONNECTORS FOR HAM OPERATORS
ANDERSON POWERPOLE CONNECTORS FOR HAM OPERATORS The Anderson Powerpole connector is a very good connector to sharing connections between users for such things as batteries, radios, chargers and other DC
More informationTHE TOOLS RECOMMENDED Phillips Screwdriver Stripper/Crimper Electrician Pliers ½ open end wrench or ratchet wrench with ½ deep socket Utility knife
16 X 20 HEATER ELEMENT WIRE CONNECTION REPAIR DK20/A/S/SP The following instructions are on the repair of a potentially faulty wire connection in your 16 x 20 heat platen. It is recommended that only those
More informationCover Page. Factory Radio Other Documents Available For This Vehicle:
Factory Radio Other Documents Available For This Vehicle: No documents available at this time Adobe Acrobat Reader Printing Tips: 1) Select FLE then PRNT and select your printer. 2) n the print options
More informationNash Chandelier Assembly and Installation Instructions
CAUTION: Nash Chandelier Assembly and Installation Instructions BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY BOX. Important
More informationGUIDE FOR WIRING HARNESS AND CONNECTOR REPAIR. This bulletin supersedes TSB 15-BE-004 to update the wiring connector ordering information.
Technical Service Bulletin GROUP BODY ELECTRICAL DATE JUNE, 2017 NUMBER MODEL(S) 17-BE-006 ALL This bulletin supersedes TSB 15-BE-004 to update the wiring connector ordering information. Description: This
More informationCustom Pendant- Hardwire Assembly and Installation Instructions
Custom Pendant- Hardwire Assembly and Installation Instructions CAUTION: BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY BOX.
More informationELECTRICALLY LONG NGP ANTENNA SYSTEMS
The K-8NGP is a tuned coaxial cable assembly that can only be used with special no-groundplane antennas. This coaxial cable will not work with any standard ground plane dependent CB antenna. We offer it
More informationIPR LA-3 KIT last update 15 march 06
IPR LA-3 KIT last update 15 march 06 PART-2: Audio Circuitry CIRCUIT BOARD LAYOUT: Power and Ground Distribution Now that your power supply is functional, it s time to think about how that power will be
More informationWoven Leather Chandelier Large Assembly and Installation Instructions
CAUTION: Woven Leather Chandelier Large Assembly and Installation Instructions BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY
More informationHOLLINGSWORTH Operating Instructions
HOLLINGSWORTH Operating Instructions H20 - Rotary Nest Hand Crimping Tool HOLLINGSWORTH (800) 638-8376 techsuppt@hollingsworth.com www.hollingsworth.com H20 Tool - Tool Warranty TOOL WARRANTY Electro-Term/Hollingsworth
More informationTRUE TECHNICAL SERVICE MANUAL - ALL MODELS. DOORS/DRAWERS/LIDS
DOORS/DRAWERS/LIDS 55 56 NOTES DOORS/DRAWERS/LIDS Swing s 73 74 NOTES INSTALLATION OF A GDM-SWING DOOR Phillips Head Screwdriver (2) - 1/8" Drift Punches (forged) Top Bracket NOTE: It may be necessary
More informationHand Crimping Tools , , and AUG 12 Rev D
Instruction Sheet 408-7332 Hand Tools 90123-2, 90123-5, and 90124-2 29 AUG 12 PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools
More information