A8430. Approximate actual size. Same pad footprint as SOT-23-5 R θja = 50 C/W, see note 1, page 2 AB SO LUTE MAX I MUM RAT INGS
|
|
- Harvey Collins
- 5 years ago
- Views:
Transcription
1 MLPD Approximate actual size GND FB AB SO LUTE MAX I MUM RAT INGS Pin V to 36 V Remaining Pins V to 10 V Ambient Operating Temperature, T A C to 8 C Junction Temperature, T J(max)...10 C Storage Temperature, T S... C to 10 C EN Same pad footprint as SOT-23- R θja = 0 C/W, see note 1, page 2 The is a noninverting boost converter that steps-up the input voltage, to provide a programmable constant current output at up to 36 V for driving white LEDs in series. Driving LEDs in series ensures identical currents and uniform brightness. Up to four white LEDs can be driven at 20 ma from a single cell or a multicell NiMH power source. Up to seven white LEDs can be driven by increasing the supply voltage up to 10 V. The incorporates a power switch and feedback sense amplifier to provide a solution with minimum external components. The output current can be set by adjusting a single external sense resistor and can be varied with a voltage or filtered PWM signal when dimming control is required. The high switching frequency of 1.2 MHz allows the use of small inductor and capacitor values. The is provided in a -pin 3 mm x 3 mm MLP package (part number suffix EK), that has a nominal height of only 0.7 mm. The lead-free version (part number suffix EK-T) has 100% lead-free matte tin leadframe plating. FEATURES Output voltage up to 36 V 2. V to 10 V input Drives up to 4 LEDs at 20 ma from a 2. V supply Drives up to LEDs at 20 ma from a 3 V supply 1.2 MHz switching frequency 300 ma switch current limit 1 µa shutdown current APPLICATIONS LED backlights Portable battery-powered equipment Cellular phones PDAs (Personal Digital Assistant) Camcorders, personal stereos, MP3 players, cameras Mobile GPS systems Use the following complete part number when ordering: Part Number Package Description EEK -pin, MLPD Surface Mount EEK-T -pin, MLPD Lead-Free, Surface Mount
2 Functional Block Diagram FB V REF 1.2 V 9 mv A1 R C C C A2 R S Q Driver Σ Ramp Generator EN 1.2 MHz Oscillator GND ELECTRICAL CHARACTERISTICS at T A = 2 C, V IN = 3 V (unless otherwise noted) Characteristics Symbol Test Conditions Min. Typ. Max. Units Input Voltage Range V IN V Supply Current I SUP Active: I LOAD = 1 ma, V LOAD = 12 V ma Shutdown (EN = 0 V) µa Feedback Reference Voltage V REF mv Feedback Input Current I FB 20 7 na Switch Current Limit I LIM 300 ma Switch Frequency F MHz Switch Maximum Duty Cycle D 8 90 % Switch Saturation voltage V CE(SAT) 30 mv Switch Leakage Current I SL µa Input Input Threshold Low V IL 0.4 V Input Threshold High V IH 1. V Input Leakage Leakage I IL 1 µa Note 1. Measured with 4-layer PCB. Please refer to application note Package Thermal Characteristics, for thermal performance measurement for 3 mm x 3 mm MLP package for additional information. 2
3 Operating Characteristics Using Typical Application Circuit (Schematic 1) Quiescent Current versus Input Voltage Quiescent Current versus Temperature Quiescent Current (ma) Quiescent Current (ma) V IN (V) Temperature ( C) Feedback Bias Current versus Temperature Switching Frequency versus Temperature Feedback Bias Current (na) 1 10 Switching Frequency (MHz) Temperature ( C) Temperature ( C) Switch Pin Voltage versus Temperature Conversion Efficiency versus Current 20 8 V CE(SAT) (mv) Efficiency (%) V IN = 3 V V IN = 4 V Temperature ( C) LED Current (ma) 3
4 Functional Description Typical Application A typical application circuit for the is provided in schematic diagram 1. This illustrates a method of driving three white LEDs in series. The conversion efficiency of this configuration is shown in chart 1. Pin Functions The diagram also shows a method of connecting the individual pins, whos functions are described as follows:. Supply to the control circuit. A bypass capacitor must be connected from close to this pin to GND.. Low-side switch connection between the inductor () and ground. Because rapid changes of current occur at this pin, the traces on the PCB that are connected to this pin should be minimized. In addition, the inductor () and diode (D1) should be connected as close to this pin as possible. EN. Setting lower than 0.4 V disables the and puts the control circuit into the low-power Sleep mode. Greater than 1. V fully enables the. GND. Ground reference connected directly to the ground plane. The sense resistor () should have a separate connection directly to this point. FB. Feedback pin for LED current control. The reference voltage is 9 mv. The top of the sense resistor () is typically connected to this pin. 22µH D1 Conversion Efficiency versus Input Voltage 9 2.V to 4.2V 1µF 0.22µF Conversion Efficiency (%) LEDs 4 LEDs LEDs V IN (V) Schematic 1. Typical application Chart 1. Conversion efficiency when driving various quantities of LEDs in the typical application circuit 4
5
6 Application Information Component Selection The component values shown in schematic 1 are sufficient for most applications. To reduce the output ripple the inductor may be increased, but in most cases this results in excessive board area and cost. Inductor Selection. With an internal PWM frequency of 1.2 MHz, the optimal inductor value for most cases is 22 µh. The inductor should have low winding resistance, typically < 1 Ω, and the core should have low losses when operating at 1.2 MHz. For worst case conditions, high output voltage and current and low input voltage, the inductor should be rated at the switch current limit, I LIM. If high temperature operation is required a derating factor will have to be considered. In some cases, where lower inductor currents are expected, the current rating can be decreased. Several inductor manufacturers have and are developing suitable small-size inductors, including: Murata, Panasonic, Sumida, Taiyo Yuden, and TDK. Diode Selection. The diode should have a low forward voltage to reduce conduction losses. In addition, it should have a low capacitance to reduce switching losses. Schottky diodes can provide both these features, if carefully selected. The forward voltage drop is a natural advantage for Schottky diodes, and it reduces as the current rating increases. However, as the current rating increases, the diode capacitance also increases. As a result, the optimal selection is usually the lowest current rating above the circuit maximum. With the, a current rating in the range from 100 ma to 200 ma is usually sufficient. Capacitor Selection. Because the capacitor values are low, ceramic capacitors are the best choice for use with the. To reduce performance variation as temperature changes, low drift capacitor types, such as X7R and XR, should be used. Suitable capacitors are available from: Taiyo Yuden, Murata, Kemet, and AVX. Dimming Control LED brightness can be controlled either by modifying the voltage at the top of the sense resistor () to control the LED current, I LOAD, directly, or by using a PWM signal on the EN pin to chop the output. Feedback modulation. By adding a voltage drop between the FB pin and (the sense resistor), as shown in schematic 2, the LED current, I LOAD, can be made to decrease. As V C (control voltage) increases, the voltage drop across R2 also increases. This causes the voltage at FB to increase, and the reduces I LOAD to compensate. As V C increases further, the current drops to zero, and R2 maintains the full 9 mv on FB. Reducing V C diminishes the voltage across R2 until, at 9 mv on V C, there is no drop across R2 and the current level is defined by. Reducing V C below 9 mv causes I LOAD to increase further, due to the voltage drop across R2 in the reverse direction. This continues until, at zero volts on V C, there is approximately mv across R2. At that point, I LOAD (ma), is defined as: I LOAD = 100 mv / where is the resistance of the sense resister (Ω). PWM Control. LED dimming control can also be generated by a filtered PWM signal as shown in schematic 3. In this case, a 0% duty cycle (PWM = 0 V) corresponds to full brightness and a 100% duty cycle causes the LED current, I LOAD, to go to zero. 2.V to 4.2V 1µF 22µH D1 V C R2 kω R3 90kΩ Schematic 2. Dimming control with dc voltage feedback modulation 0.22µF 6
7 By applying a PWM signal directly to the EN pin, the is turned on or off, and I LOAD is either full (as defined by ) or zero. By varying the duty cycle of the PWM signal, the LED brightness can be controlled from off (0% duty cycle) to full (100% duty cycle). The PWM frequency should be in the range from 1 khz to 10 khz. Several other schemes are possible, for example, digitally switching additional resistors across to increase I LOAD. In this case, would be selected for the minimum desired brightness. Soft Start-Up To provide fast start-up operation, no soft start is implemented in the control circuit. At power-on, the bypass capacitor () is discharged, which means that the supply must provide the in-rush current through the inductor. This can be reduced by modulating the feedback with a softstart circuit as shown in schematic 4. When power is first applied, the capacitor C3 is discharged and pulls the FB pin high, reducing the output drive to minimum. As C3 charges, when the bottom drops below about 0.8 V, the feedback from the sense resistor () takes over full control of the output current. Overvoltage Protection An overvoltage event can occur when the LEDs become disconnected or fail in an open state. In these cases, the current flow through the sense resistor becomes zero, thus the feedback voltage becomes zero. The compensates by increasing the on time of the switch, which increases the output voltage. 2. V to 4.2 V 1 µf V C (PMW) 22 µh D1 A843 R4 10 kω R3 90 kω C3 100 nf R2 kω Schematic 3. Dimming control with filtered PWM 2.V to 4.2V 1µF 22µH D1 Schematic 4. Soft start operation C3 2.2 nf R2 1kΩ R3 kω 6.3 Ω 0.22 µf 0.22µF 7
8 Overvoltage protection for the requires a Zener diode to clamp the output voltage, as shown in schematic. The Zener voltage should be greater than the maximum output voltage of the LED string. The Zener diode also should be able to sink more than 0.1 ma of current. Parallel LED Strings The can be used to power parallel strings of LEDs, which have the same number of LEDs on each string. It is important that the voltage drop is the same across all of the parallel strings, to ensure that all of the LEDs are illuminated and that the current though each string is equal. A typical circuit with two parallel strings is shown in schematic 6. The coversion efficiency of this configuration is shown in chart 2. 2.V to 4.2V 1µF 22µH D1 R2 1kΩ Schematic. Overvoltage protection with Zener clamp 22µH D1 0.22µF 1µF 0.22µF 2.V to 4.2V R2 Schematic 6. Parallel strings of LEDs Conversion Efficiency for Two Parallel Strings 9 90 Efficiency (%) Two 3-LED strings Two 4-LED strings Two 7-LED strings Input Voltage (V) Chart 2. Conversion efficiency when driving two parallel strings of varying lengths 8
9 Terminal List Table Pin Name Function 1 Internal power FET 2 GND Ground 3 FB Feedback input 4 EN input Input supply Package EK 3.00 BSC.118 A BSC REF NOM 0.0 MIN.020 R0.20 REF NOM 0.1 MIN B 0.0 MIN Dimensions in millimeters U.S. Customary dimensions (in.) in brackets, for reference only A Pin index area B Exposed thermal pad C Optional thermal vias, 0.30 [.012], pitch 1.2 [.047] D Typical pad layout including solder pad for exposed thermal pad; adjust as necessary to meet application process requirements E Typical pad layout with contact pads only; adjust as necessary to meet application process requirements REF 0.20 REF.008 C 1.10 MAX REF E BSC.037 D BSC MAX.083 9
10 The products described here are manufactured under one or more U.S. patents or U.S. patents pending. Allegro MicroSystems, Inc. reserves the right to make, from time to time, such de par tures from the detail speci fi ca tions as may be required to permit improvements in the per for mance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the information being relied upon is current. Allegro products are not authorized for use as critical components in life-support devices or sys tems without express written approval. The in for ma tion in clud ed herein is believed to be ac cu rate and reliable. How ev er, Allegro MicroSystems, Inc. assumes no re spon si bil i ty for its use; nor for any in fringe ment of patents or other rights of third parties which may result from its use. Copyright 2003, 2004, 200 AllegroMicrosystems, Inc. 10
Discontinued Product
Discontinued Product These parts are no longer in production The device should not be purchased for new design applications. Samples are no longer available. Date of status change: May 3, 2010 Recommended
More informationA8431. White LED Driver Constant Current Step-up Converter
Features and Benefits Output voltage up to 32 V ( level) 2. to 0 V input Drives up to 4 LEDs at 20 ma from a 2. V supply Drives up to LEDs at 20 ma from a 3 V supply.2 MHz switching frequency 300 ma switch
More informationACT6311. White LED/OLED Step-Up Converter FEATURES
White LED/OLED Step-Up Converter FEATURES Adjustable Output Voltage Drives OLEDs or White LEDs 30V High Voltage Switch 1MHz Switching Frequency Tiny Inductors and Capacitors Tiny SOT23-5 Package APPLICATIONS
More informationA8499. High Voltage Step-Down Regulator
Features and Benefits 8 to 0 V input range Integrated DMOS switch Adjustable fixed off-time Highly efficient Adjustable. to 4 V output Description The A8499 is a step down regulator that will handle a
More informationAT731 White LED Step-Up Converter
FEATURES DESCRIPTION Inherently Matched LED Current High Efficiency: 84% Typical Drives Up to Four LEDs from a 3.2V Supply Drives Up to Eight LEDs from a 5V Supply 36V Rugged Bipolar Switch Fast 1.2MHz
More informationLDS8710. High Efficiency 10 LED Driver With No External Schottky FEATURES APPLICATION DESCRIPTION TYPICAL APPLICATION CIRCUIT
High Efficiency 10 LED Driver With No External Schottky FEATURES High efficiency boost converter with the input voltage range from 2.7 to 5.5 V No external Schottky Required (Internal synchronous rectifier*)
More informationA3982. DMOS Stepper Motor Driver with Translator
OUT2A SENSE2 VBB2 OUT2B ENABLE PGND PGND CP1 CP2 VCP VREG MS1 1 2 3 4 5 6 7 8 9 10 11 12 Charge Pump Reg Package LB Translator & Control Logic AB SO LUTE MAX I MUM RAT INGS Load Supply Voltage,V BB...35
More informationHigh Voltage CMOS Boost White LED Driver
High Voltage CMOS Boost White LED Driver FEATURES Drives 6 to 8 White LEDs in series from 3V Up to 87% Efficiency Low Quiescent Ground Current 0.6mA Adjustable Output Current (up to 40mA) High Frequency
More informationHigh Voltage CMOS Boost White LED Driver
High Voltage CMOS Boost White LED Driver FEATURES Drives 6 to 8 White LEDs in series from 3V Up to 87% Efficiency Low Quiescent Ground Current 0.6mA Adjustable Output Current (up to 40mA) High Frequency
More informationBoost (Step-up) WLED Driver with OVP
Boost (Step-up) WLED Driver with OVP DESCRIPTION The TS19371 is a step-up DC/DC converter specifically designed to drive white LEDs with a constant current. The device can drive up to 126 LEDs (9S14P)
More information20mA R FB. Fig. 1 Li-Ion Powered Driver with Over Voltage Protection for Three White LEDs
White LED Step-Up Converter in SOT23 FEATURES 1.2MHz Fixed Frequency Current-Mode PWM Operation. Efficiency Up to 84% at, 3LEDs, I LED = Adjustable Output Voltage up to 30V Low Supply Current: µa Matches
More informationBCT3756 Small Package, High Performance, Asynchronies Boost for 8 Series WLED Driver
BCT3756 Small Package, High Performance, Asynchronies Boost for 8 Series WLED Driver Features 3.0V to 5.5V Input Voltage Range Internal Power N-MOSFET Switch Wide Range for PWM Dimming(10kHz to 100kHz)
More informationA4941. Three-Phase Sensorless Fan Driver
Features and Benefits Sensorless (no Hall sensors required) Soft switching for reduced audible noise Minimal external components PWM speed input FG speed output Low power standby mode Lock detection Optional
More informationFeatures. Applications
White LED Driver Internal Schottky Diode and OVP General Description The is a PWM (pulse width modulated), boostswitching regulator that is optimized for constant-current white LED driver applications.
More informationBCT3692B Small Package, High Performance, Asynchronies Boost for 10 WLED Driver
BCT3692B Small Package, High Performance, Asynchronies Boost for 10 WLED Driver Features 3.0V to 5.5V Input Voltage Range Internal Power N-MOSFET Switch Wide Range for PWM Dimming(20kHz to 60kHz) Minimize
More informationEUP MHz, 800mA Synchronous Step-Down Converter with Soft Start
1.5MHz, 800mA Synchronous Step-Down Converter with Soft Start DESCRIPTION The is a constant frequency, current mode, PWM step-down converter. The device integrates a main switch and a synchronous rectifier
More informationFAN MHz TinyBoost Regulator with 33V Integrated FET Switch
FAN5336 1.5MHz TinyBoost Regulator with 33V Integrated FET Switch Features 1.5MHz Switching Frequency Low Noise Adjustable Output Voltage Up to 1.5A Peak Switch Current Low Shutdown Current:
More informationMIC2287. Features. General Description. Applications. Typical Application. 1.2MHz PWM White LED Driver with OVP in 2mm 2mm MLF and Thin SOT-23
MIC2287 1.2MHz PWM White LED Driver with OVP in 2mm 2mm MLF and Thin SOT-23 General Description The MIC2287 is a 1.2MHz pulse width modulated (PWM), boost-switching regulator that is optimized for constantcurrent,
More informationA6850. Dual Channel Switch Interface IC. Features and Benefits 4.75 to 26.5 V operation Low V IN -to-v OUT voltage drop 1 / 10 current sense feedback
Features and Benefits 4.75 to 6.5 V operation Low V IN -to-v OUT voltage drop 1 / 10 current sense feedback Survive short-to-battery and short-to-ground faults Survive 40 V load dump >4 kv ESD rating on
More information1.5MHz, 800mA Synchronous Step-Down Regulator
1.5MHz, 800mA Synchronous Step-Down Regulator General Description The is a high efficiency current mode synchronous buck PWM DC-DC regulator. The internal generated 0.6V precision feedback reference voltage
More informationTFT-LCD DC/DC Converter with Integrated Backlight LED Driver
TFT-LCD DC/DC Converter with Integrated Backlight LED Driver Description The is a step-up current mode PWM DC/DC converter (Ch-1) built in an internal 1.6A, 0.25Ω power N-channel MOSFET and integrated
More informationConstant Current Switching Regulator for White LED
Constant Current Switching Regulator for White LED FP7201 General Description The FP7201 is a Boost DC-DC converter specifically designed to drive white LEDs with constant current. The device can support
More informationWD3122EC. Descriptions. Features. Applications. Order information. High Efficiency, 28 LEDS White LED Driver. Product specification
High Efficiency, 28 LEDS White LED Driver Descriptions The is a constant current, high efficiency LED driver. Internal MOSFET can drive up to 10 white LEDs in series and 3S9P LEDs with minimum 1.1A current
More informationBuilt-In OVP White LED Step-up Converter in Tiny Package
Built-In White LED Step-up Converter in Tiny Package Description The is a step-up DC/DC converter specifically designed to drive white LEDs with a constant current. The device can drive up to 4 LEDs in
More informationApplication Battery Power Equipment Notebook Computers PDA Cellular Phone Digital Cameras MP3 Players GPS Receivers
General Description The is a step-up DC/DC converter specifically designed to drive white LEDs with a constant current. The device can drive two, three or four LEDs in series from a Li-Ion cell. Series
More informationFeatures. Applications
White LED Driver Internal Schottky Diode and OVP General Description The is a PWM (pulse width modulated), boostswitching regulator that is optimized for constant-current white LED driver applications.
More informationA3949. DMOS Full-Bridge Motor Driver. Features and Benefits Single supply operation Very small outline package Low R DS(ON)
Features and Benefits Single supply operation Very small outline package Low R DS(ON) outputs Sleep function Internal UVLO Crossover current protection Thermal shutdown protection Packages: Description
More informationA3909. Dual Full Bridge Motor Driver. Description. Features and Benefits. Packages: Functional Block Diagram
Features and Benefits Low R DS(on) outputs Drives two DC motors or single stepper motor Low power standby (Sleep) mode with zero current drain Thermal shutdown protection Parallel operation option for.8
More informationA3901. Dual Full Bridge Low Voltage Motor Driver
A39 Features and Benefits ow R DS(on) outputs Full- and half-stepping capability Small package Forward, reverse, and brake modes for DC motors Sleep mode with zero current drain PWM control up to 25 khz
More informationMP MHz, 700mA, Fixed-Frequency Step-Up Driver for up to 10 White LEDS
MP3301 1.3MHz, 700mA, Fixed-Frequency Step-Up Driver for up to 10 White LEDS DESCRIPTION The MP3301 is a step-up converter designed to drive WLEDS arrays from a single-cell, lithium-ion battery. The MP3301
More informationPL6T611 High Efficiency LED Driver
High Efficiency LED Driver Description The is a current-mode and fixed frequency 600kHz boost converter with an integrated N-FET to drive white LEDs. The series connection allows the LED current to be
More informationDescription. Typical Application. CIN μf Efficiency % VOUT 3.3 V / 3 A ESR COUT.
Features and Benefits 8 to 50 V input range Integrated DMOS switch Adjustable fixed off-time Highly efficient Adjustable 0.8 to 24 V output Package: 8-Lead SOIC with exposed thermal pad (suffix LJ) Description
More informationMIC YML MIC YML
MIC2292/93 High Frequency PWM White LED Drivers with Internal Schottky Diode and OP General Description The MIC2292 and MIC2293 are high frequency, Pulse Width Modulator (PWM) boost regulators optimized
More informationMicro Power Boost Regulator Series White LED Driver L1 D1 SP6691 GND
Micro Power Boost Regulator Series White LED Driver FEATURES Drives up to 6 LEDs @ 5mA Drives up to 8 LEDs @ 0mA High Output Voltage: Up to 0V Optimized for Single Supply,.7V - Applications Operates Down
More informationAdvanced Monolithic Systems
Advanced Monolithic Systems FEATURES Internal Power Switch Output Voltage up to 20V Up to 89% Efficiency Low 0.08µA Shutdown Supply Current Internal Current Limit Thermal Shutdown Available in 5-Pin SOT-23
More informationYB1520 Step-up DC-DC Converter, White LED Driver
Description The YB1520 is a step-up DC-DC converter; operates as current source to drive up to 18 white LEDs in parallel/series configuration. Series connecting of the LEDs provides identical LED currents
More informationPWM Step-Up DC/DC Converter for Panel Backlight. Features. Fig. 1
PWM Step-Up DC/DC Converter for Panel Backlight General Description The designed with high efficiency step up DC/DC converter for driving white LEDs. The device can drive up 11 white LEDs from a single
More information1.5MHz, 3A Synchronous Step-Down Regulator
1.5MHz, 3A Synchronous Step-Down Regulator FP6165 General Description The FP6165 is a high efficiency current mode synchronous buck PWM DC-DC regulator. The internal generated 0.6V precision feedback reference
More informationHigh-Efficiency, 40V Step-Up Converters for 2 to 10 White LEDs MAX1553/MAX1554
EVALUATION KIT AVAILABLE /MAX1554 General Description The /MAX1554 drive white LEDs in series with a constant current to provide efficient display backlighting in cellular phones, PDAs, and other hand-held
More informationMIC BML MIC BML
MIC9/93 High Frequency PWM White LED Drivers with Internal Schottky Diode and OVP General Description The MIC9 and MIC93 are high frequency, Pulse Width Modulator (PWM) boost regulators optimized for constantcurrent,
More informationC2 0.22μF. 15mA F01a PIN PIN NAME PIN DESCRIPTION
WHITE E STEP-UP CONVERTER FEATURES Inherently Matched E Current High Efficiency: 84% Typical rives Up to Four Es from a 3.2V Supply rives Up to Six Es from a 5V Supply 36V Rugged Bipolar Switch Fast 1.2MHz
More informationA4950. Full-Bridge DMOS PWM Motor Driver. Description
Features and Benefits Low R DS(on) outputs Overcurrent protection (OCP) Motor short protection Motor lead short to ground protection Motor lead short to battery protection Low Power Standby mode Adjustable
More informationThe ASD5001 is available in SOT23-5 package, and it is rated for -40 to +85 C temperature range.
General Description The ASD5001 is a high efficiency, step up PWM regulator with an integrated 1A power transistor. It is designed to operate with an input Voltage range of 1.8 to 15V. Designed for optimum
More informationUNISONIC TECHNOLOGIES CO., LTD
UNISONIC TECHNOLOGIES CO., LTD WHITE LED STEP-UP CONVERTER DESCRIPTION The UTC L5101 is a constant current step-up PWM DC/DC converter optimized to drive white LEDs. It can drive LEDs in series with a
More informationDiscontinued Product
Discontinued Product This device is no longer in production. The device should not be purchased for new design applications. Samples are no longer available. Date of status change: October 31, 011 Recommended
More informationMIC2287. Features. General Description. Applications. Typical Application CMDSH MHz PWM White LED Driver with OVP in 2mm 2mm MLF and Thin SOT-23
MIC2287 1.2MHz PWM White LED Driver with OVP in 2mm 2mm MLF and Thin SOT-23 General Description The MIC2287 is a 1.2MHz pulse width modulated (PWM), boost-switching regulator that is optimized for constantcurrent,
More informationESMT/EMP Preliminary EMD2055
Preliminary EMD2055 PWM Step-Up DC/DC Converter for Panel Backlight (11 WLEDs Driver) General Description The EMD2055 is a highly efficient, step-up DC/DC converter for driving white LEDs. The device can
More informationMIC2291. General Description. Features. Applications. Typical Application. 1.2A PWM Boost Regulator Photo Flash LED Driver
1.2A PWM Boost Regulator Photo Flash LED Driver General Description The is a 1.2MHz Pulse Width Modulation (PWM), boost-switching regulator that is optimized for high-current, white LED photo flash applications.
More informationWD3119 WD3119. High Efficiency, 40V Step-Up White LED Driver. Descriptions. Features. Applications. Order information 3119 FCYW 3119 YYWW
High Efficiency, 40V Step-Up White LED Driver Http//:www.sh-willsemi.com Descriptions The is a constant current, high efficiency LED driver. Internal MOSFET can drive up to 10 white LEDs in series and
More informationRT9285A/B. Tiny Package, High Performance, Diode Embedded White LED Driver. Preliminary. Features. General Description.
General Description The RT9285 is a high frequency asynchronous boost converter with internal diode, which can support 2 to 5 White LEDs for backlighting and OLED power supply. The Internal soft start
More informationTS19371 Boost (Step-up) WLED Driver with OVP
SOT-26 Pin Definition: 1. SW 6. VIN 2. GND 5. OVP 3. FB 4. CTRL General Description The is a step-up DC/DC converter specifically designed to drive white LEDs with a constant current. The device can drive
More informationUDN2987x-6. DABIC-5 8-Channel Source Driver with Overcurrent Protection
Package A, 20-pin DIP Package LW, 20-pin SOIC-W Approximate Scale 1:1 Providing overcurrent protection for each of its eight sourcing outputs, the UDN2987A-6 and UDN2987LW-6 drivers are used as an interface
More informationCAT4137. CMOS Boost Converter - White LED Driver
CMOS Boost Converter - White LED Driver Description The CAT4137 is a DC/DC step-up converter that delivers a regulated output current. Operation at a constant switching frequency of 1 MHz allows the device
More informationWhite LED Step-Up Converter (Preliminary) Features. Application. Package Ordering Information Marking Information SOT-23-5L SE3506-LF
Description The is a step-up DC/DC converter specifically designed to drive white LEDs with a constant current. The device can drive two, three, four, or five LEDs in series from a Li-Ion cell. Series
More information350mA High Efficiency Step Down LED Driver
35mA High Efficiency Step Down LED Driver CAT421 FEATURES LED drive current up to 35mA 12V and 24V system compatible Handles transients up to 4V Single Pin Control and Dimming function Power Efficiency
More informationADT7350. General Description. Features. Applications. Typical Application Circuit. Sep / Rev. 0.
General Description The ADT7350 is a step-down converter with integrated switching MOSFET. It operates wide input supply voltage range from 4.5V to 24V with 1.2A peak output current. It includes current
More informationA8160A. AiT Semiconductor Inc. APPLICATION ORDERING INFORMATION TYPICAL APPLICATION
DESCRIPTION The is a step-up DC-DC converter specifically designed for driving white LEDs with a constant current. The internal MOSFET can support up to 10 White LEDs for backlighting and OLED power application,
More informationeorex EP MHz, 600mA Synchronous Step-down Converter
1.5MHz, 600mA Synchronous Step-down Converter Features High Efficiency: Up to 96% 1.5MHz Constant Switching Frequency 600mA Output Current at V IN = 3V Integrated Main Switch and Synchronous Rectifier
More informationPWM Step-Up DC/DC Converter for Panel Backlight. Applications. Features. Fig. 1
PWM Step-Up DC/DC Converter for Panel Backlight General Description The is a highly efficient, step-up DC/DC converter for driving white LEDs. The device can drive up to 9 serially connected white LEDs
More informationADT7350. General Description. Applications. Features. Typical Application Circuit. Aug / Rev. 0.
General Description The ADT7350 is a step-down converter with integrated switching MOSFET. It operates wide input supply voltage range from 4.5V to 24V with 1.2A peak output current. It includes current
More informationTS1518 Step-Up DC-DC Converter, White LED Driver
SOT-25 Pin Definition: 1. SW 2. Ground 3. Feedback 4. CTRL 5. Input General Description The TS1518 is a step-up DC-DC converter; operates as current source to drive up to 6 white LEDs(V IN at 3.0V) or
More informationMP1521 High Efficiency White LED Driver
General Description The is a constant-current Boost Regulator. This IC has three individual current-sensing feedbacks, which are ideal for driving multiple strings of series connected LEDs. The OLS pin
More informationFAN5345 Series Boost LED Driver with Single-Wire Digital Interface
September 2011 FAN5345 Series Boost LED Driver with Single-Wire Digital Interface Features Asynchronous Boost Converter Drives LEDs in Series: FAN5345S20X: 20V Output FAN5345S30X: 30V Output 2.5V to 5.5V
More informationACT111A. 4.8V to 30V Input, 1.5A LED Driver with Dimming Control GENERAL DESCRIPTION FEATURES APPLICATIONS TYPICAL APPLICATION CIRCUIT
4.8V to 30V Input, 1.5A LED Driver with Dimming Control FEATURES Up to 92% Efficiency Wide 4.8V to 30V Input Voltage Range 100mV Low Feedback Voltage 1.5A High Output Capacity PWM Dimming 10kHz Maximum
More informationRT V DC-DC Boost Converter. Features. General Description. Applications. Ordering Information. Marking Information
RT8580 36V DC-DC Boost Converter General Description The RT8580 is a high performance, low noise, DC-DC Boost Converter with an integrated 0.5A, 1Ω internal switch. The RT8580's input voltage ranges from
More informationMT3540 Rev.V1.2. Package/Order Information. Pin Description. Absolute Maximum Ratings PIN NAME FUNCTION
1.5A, 1.2MHz, Up to 28V Output Micropower Step-up Converter FEATURES Integrated 0.5Ω Power MOSFET 40µA Quiescent Current 2.5V to 5.5V Input Voltage 1.2MHz Fixed Switching Frequency Internal 1.5A Switch
More information1.5MHz, 600mA Synchronous Step-Down Regulator
1.5MHz, 600mA Synchronous Step-Down Regulator FP6160B General Description The FP6160B is a high efficiency current mode synchronous buck PWM DC-DC regulator. The internal generated 0.6V precision feedback
More informationACT MHz, 600mA Synchronous Step Down Converter in SOT23-5 GENERAL DESCRIPTION FEATURES APPLICATIONS. Data Sheet Rev 0, 5/2006
Data Sheet Rev 0, 5/2006 ACT6906 1.6MHz, 600mA Synchronous Step Down Converter in SOT23-5 FEATURES High Efficiency - Up to 95% Very Low 24µA Quiescent Current Guaranteed 600mA Output Current 1.6MHz Constant
More informationEUP2511. HQI Boost Converter With 2.1A Switch In Tiny SOT-23 Package FEATURES DESCRIPTION APPLICATIONS. Typical Application Circuit
HQI Boost Converter With 2.1A Switch In Tiny SOT-23 Package DESCRIPTION The is a high performance current mode, PWM step-up converter. With an internal 2.1A, 150mΩ MOSFET, it can generate 5 at up to 900mA
More informationA3984. DMOS Microstepping Driver with Translator
Features and Benefits Low RDS(ON) outputs Automatic current decay mode detection/selection and current decay modes Synchronous rectification for low power dissipation Internal UVLO and thermal shutdown
More informationDIO V Step-Up LED Driver with PWM to Constant Current Dimming Mode
Rev 0.2 DIO5061 37V Step-Up LED Driver with PWM to Constant Current Dimming Mode Features Drive up to 10 serial LEDs PWM to Constant Current dimming mode Integrated 40V high current switch (1.3A limit)
More informationA MHz, 600mA S YNCHRONOUS STEP-DOWN CONVERTER. Thermal Resistance. Top View. Ordering Information. θ JC. θ JA. Part Number A7106E5-Adj
Description Features The is a 1.5MHz constant frequency, slope compensated current mode PWM step-down converter. The device integrates a main switch and a synchronous rectifier for high efficiency without
More informationMIC2290. General Description. Features. Applications. Typical Application. 2mm 2mm PWM Boost Regulator with Internal Schotty Diode
2mm 2mm PWM Boost Regulator with Internal Schotty Diode General Description The is a 1.2MHz, PWM, boost-switching regulator housed in the small size 2mm 2mm 8-pin MLF package. The features an internal
More information1.5MHz, 1A Synchronous Step-Down Regulator
1.5MHz, 1A Synchronous Step-Down Regulator FP6161 General Description The FP6161 is a high efficiency current mode synchronous buck PWM DC-DC regulator. The internal generated 0.6V precision feedback reference
More informationFAN LED Series Boost LED Driver with Integrated Schottky Diode and Single-Wire Digital Interface
FAN5343 6-LED Series Boost LED Driver with Integrated Schottky Diode and Single-Wire Digital Interface Features Asynchronous Boost Converter V OUT up to 24V Internal Schottky Diode Up to 500mW Output Power
More informationEUP2584. White LED Step-Up Converter In Tiny SOT-23 Package FEATURES DESCRIPTION APPLICATIONS. Typical Application Circuit
White LED Step-Up Converter In Tiny SOT-23 Package DESCRIPTION The is a constant current step-up converter specifically designed to drive white LEDs. The Step-up converter topology allows series connection
More information23V 3A Step-Down DC/DC Converter
23V 3A Step-Down DC/DC Converter FEATURES 3A Continuous Output Current Programmable Soft Start 100mΩ Internal Power MOSFET Switch Stable with Low ESR Output Ceramic Capacitors Up to 95% Efficiency 22µA
More information1.5 MHz, 600mA Synchronous Step-Down Converter
GENERAL DESCRIPTION is a 1.5Mhz constant frequency, slope compensated current mode PWM step-down converter. The device integrates a main switch and a synchronous rectifier for high efficiency without an
More informationACT8310/ A, PWM Step-Down DC/DCs in TDFN GENERAL DESCRIPTION FEATURES APPLICATIONS SYSTEM BLOCK DIAGRAM ACT8311. Rev 4, 08-Feb-2017
1.5A, PWM Step-Down DC/DCs in TDFN FEATURES Multiple Patents Pending Up to 95% High Efficiency Up to 1.5A Guaranteed Output Current (ACT8311) 1.35MHz Constant Frequency Operation Internal Synchronous Rectifier
More informationDual 1.5MHz, 1A Synchronous Step-Down Regulator
Dual 1.5MHz, 1A Synchronous Step-Down Regulator FP6166 General Description The FP6166 is a high efficiency current mode dual synchronous buck PWM DC-DC regulator. The internal generated 0.6V precision
More informationEUP3010/A. 1.5MHz,1A Synchronous Step-Down Converter with Soft Start DESCRIPTION FEATURES APPLICATIONS. Typical Application Circuit
1.5MHz,1A Synchronous Step-Down Converter with Soft Start DESCRIPTION The is a constant frequency, current mode, PWM step-down converter. The device integrates a main switch and a synchronous rectifier
More informationDiscontinued Product
Dual Full-Bridge PWM Motor Driver Discontinued Product This device is no longer in production. The device should not be purchased for new design applications. Samples are no longer available. Date of status
More informationA7632A. AiT Semiconductor Inc. APPLICATION ORDERING INFORMATION TYPICAL APPLICATION
DESCRIPTION The is a constant frequency, current mode step-up converter intended for small, low power applications. The switches at 1.2MHz and allows the use of tiny, low cost capacitors and inductors
More informationYB1506 Step-up DC-DC Converter, White LED Driver
Description The YB1506 is a step-up(boost) DC-DC converter; operate as current source to drive up to 5 white LEDs in series. Series connecting of the LEDs provides identical LED currents resulting in uniform
More informationA3995. DMOS Dual Full Bridge PWM Motor Driver
Features and Benefits 6 V output rating.4 A, DC motor driver Synchronous rectification Internal undervoltage lockout (UVLO) Thermal shutdown circuitry Crossover-current protection Very thin profile QFN
More informationFAN5340 Synchronous Constant-Current Series Boost LED Driver with PWM Brightness Control and Integrated Load Disconnect
April 2010 FAN5340 Synchronous Constant-Current Series Boost LED Driver with PWM Brightness Control and Integrated Load Disconnect Features Synchronous Current-Mode Boost Converter Up to 500mW Output Power
More informationTS19371 Boost (Step-up) WLED Driver with OVP
SOT-26 Pin Definition: 1. SW 6. VIN 2. GND 5. OVP 3. FB 4. CTRL SOP-8 Pin Definition: 1. VIN 8. SW 2. GND 7. GND 3. GND 6. GND 4. CTRL 5. FB General Description The TS19371 is a step-up DC/DC converter
More informationSC122. Low Voltage Synchronous Boost Converter. POWER MANAGEMENT Features. Description. Applications. Typical Application Circuit SC122
POWER MANAGEMENT Features Input voltage 0.7V to 1.6V Minimum start-up voltage 0.85V Output voltage fixed at 3.3V Peak input current limit 350mA typically Output current 95mA at = 1.6V, 50mA at = 0.9V Efficiency
More informationSGM3736 PWM Dimming, 38V Step-Up LED Driver
GENERAL DESCRIPTION The SGM3736 is a versatile constant current LED driver with a high efficiency step-up converter architecture. The low-side power MOSFET is integrated in the device, significantly shrinking
More informationCurrent Sensor: ACS755SCB-200
Pin 1: VCC Pin 2: GND Pin 3: VOUT Terminal 4: IP+ Terminal 5: IP AB SO LUTE MAX I MUM RAT INGS Supply Voltage, V CC...16 V Reverse Supply Voltage, V RCC... 16 V Output Voltage, V OUT...16 V Reverse Output
More informationMicro Power Boost Regulator Series White LED Driver
Micro Power Boost Regulator Series White LED Driver FEATURES High Output Voltage: Up to 0V Optimized for Single Supply,.7V -.V Applications Operated Down to V High Efficiency: Greater Than 75% Low Quiescent
More informationACT MHz, 600mA Synchronous Step Down Converter in SOT23-5 FEATURES GENERAL DESCRIPTION APPLICATIONS. Data Sheet Rev 0, 5/2006
Data Sheet Rev 0, 5/2006 ACT6907 1.6MHz, 600mA Synchronous Step Down Converter in SOT23-5 FEATURES High Efficiency - Up to 95% Very Low 24µA Quiescent Current Guaranteed 600mA Output Current 1.6MHz Constant
More informationMIC2295. Features. General Description. Applications. High Power Density 1.2A Boost Regulator
High Power Density 1.2A Boost Regulator General Description The is a 1.2Mhz, PWM dc/dc boost switching regulator available in low profile Thin SOT23 and 2mm x 2mm MLF package options. High power density
More informationV OUT C1P C2P C1N GND C2N EN/PWM SP6682 V IN V MODE FB
FEATURES Ideal For White LED Driver Low Profile, Inductorless Regulator X. and X Modes for Highest Efficiency +.7V to +.V Input Voltage Range Fast Turn-On Time, 7µS ma Quiescent Current
More informationA7108. AiT Semiconductor Inc. APPLICATION ORDERING INFORMATION TYPICAL APPLICATION
DESCRIPTION The is a high efficiency monolithic synchronous buck regulator using a constant frequency, current mode architecture. The device is available in an adjustable version. Supply current with no
More informationMIC2296. General Description. Features. Applications. High Power Density 1.2A Boost Regulator
High Power Density 1.2A Boost Regulator General Description The is a 600kHz, PWM dc/dc boost switching regulator available in a 2mm x 2mm MLF package option. High power density is achieved with the s internal
More informationHigh-Efficiency, 40V White LED Driver with Dimming Control
High-Efficiency, 40V White LED Driver with Dimming Control Description The is a step-up DC/DC converter specifically designed for driving WLEDs with a constant current. The can drive up 10 white LEDs in
More informationMP A Fixed Frequency White LED Driver
The Future of Analog IC Technology DESCRIPTION The is a step-up converter designed for driving up to 39 white LEDs (13 strings of 3 LEDs each) from a 5V system rail. The uses a current mode, fixed frequency
More informationLast Time Buy. Deadline for receipt of LAST TIME BUY orders: April 30, 2011
Last Time Buy This part is in production but has been determined to be LAST TIME BUY. This classification indicates that the product is obsolete and notice has been given. Sale of this device is currently
More informationYB1522 Step-up DC-DC Converter White LED Driver
Description The YB1522 is a step-up DC-DC converter; with wide input voltage range from 3V to 16V, which operates as current source to drive up to 3S7P to 3S1P (V IN at 3V to 5V). Series connecting of
More information