Emerson (Appleton Group ATX)

Transcription

1 These assemblies are available in AC-powered and DC-powered versions. They have space to land 48 or 96 CHARM I/O depending on the model chosen. The field I/O can be specified as either IS or NON-IS I/O. The enclosures are designed to be mounted in the field and serve as a landing place for I/O in the field. The enclosure sends the I/O information back to the controller of the DCS system (distributed control system) via Ethernet connection. End users must follow specific installation and operating instructions supplied by the manufacturer to prevent exceeding the heat dissipating limits for the desired temperature code for an operating ambient. The equipment is essentially an assembly of certified parts and comprises the following: General Components: JBESG junction box certified (Ex e IIC Gb) under IECEx CSA U. Roxtec cable gland certified (Ex e IIC Gb) under IECEx NEM X. CMP cable glands listed below: Type TC (Ex d e IIC Gb) certified IECEx SIR X. CMP stopping plug, series 757 (Ex d IIC Gb/ or Ex e IIC Gb) certified under IECEx SIR X. CMP cable gland Type A2F (Ex d IIC Gb/ Ex e IIC Gb) certified under / IECEx SIR X. Intertec TAE Thermostat (Ex d IIC) certified under IECEx PTB Intertec Heater model CP MULTITHERM (Ex db IIC) certified under IECEx PTB X. CMP Breather Type 781E (Ex e IIC Gb) certified under IECEx SIR U. APPLETON/ATX fuse (Ex d e IIC Gb) certified under IECEx LCIE U. APPLETON/ ATX Breaker assembly (Ex d e IIC Gb) certified under IECEx INE U. Emerson power supplies listed below: SDN C (Ex na nc IIC Gb) certified under IECEx UL U. SDN C (Ex na nc IIC Gb) certified under IECEx UL U. SDN C (Ex na nc IIC Gb) certified under IECEx UL U. Redundancy power supply model SDN 2X20RED (Ex na nc IIC Gb) certified IECEx UL X. Single port DeltaV Fiber Switch Type KJ1710X1-BA1 (Ex na [op is Ga] IIC Gb) certified under IECEx DEK X. PHOENIX Contact Terminal Blocks (Ex e IIC Gb) certified under IECEx KEM U. Date: 04 August 2016 Page 1 of 6

2 DeltaV Hardware Components: Emerson DeltaV Hardware components listed below certified under IECEx FMG U: CHARMs Smart Logic Solver Carrier model KL4103X1-BA1 (Ex na IIC Gc) Power Module, Redundant CSLS model KL1501X1 BA1(Ex na IIC Gc) Charm Safety Logic Solver (CSLS) model KL2001X1 BA1 (Ex na IIC Gc) Safety Network Port Copper model KL1603X1-BA1 (Ex na IIC Gc) CHARM Standard Terminal model KL4502X1-BA1 (Ex na ic IIC Gc) Address Plugs models KL4501X1-BA1, KL4501X1-BB1, KL4501X1-BC1, KL4501X1-BD1, KL4501X1-BE1, KL4501X1-BF1, KL4501X1-BG1 and KL4501X1-BH1 (Ex na IIC Gc) LS DI 24 VDC Dry Contact model KL3003X1-LS1 (Ex na [ic] IIC Gc), Entity Parameters: Uo = 26.4V, Io = 14mA, Co = 0.11μF, Lo = 75mH Dual Media Converter Carrier model KL1720X1-BA1 (Ex na IIC Gc) Media Converter 1-Port Multimode Module model KL1720X1-BC1 (Ex na IIC Gc) Media Converter 1-Port Single-Mode Module model KL1720X1-BB1 (Ex na IIC Gc) I/O Port Switch Module; Fiber model KL1602X1-BA1 ((Ex na IIC Gc) Ethernet Isolation Port Copper model KL1604X1-BA1 (Ex na IIC Gc) SZ Controller model KL2001X1-BB1 (Ex na IIC Gc) LS DI NAMUR CHARM, model KL3001X1-LS1 (Ex [ic] na IIC Gc) Entity Parameters: Uo = 12.6V, Io = 8.5mA, Co = 6.8μF, Lo = 1H Discrete In, +12VDC Dry Contact/ Namur, model KL3001X1-BA1 (Ex [ic] na IIC Gc) Entity Parameters: Uo = 12.6V, Io = 8.5mA, Co = 6.8μF, Lo = 1H LS DI 24 VDC Low-Side CHARM, model KL3003X1-LS1 (Ex [ic] na IIC Gc) Entity Parameters: Uo = 26.4V, Io = 14mA, Co = 0.11μF, Lo = 75mH Discrete In, +24VDC Dry Contac t (Low Side Sense), model KL3003X1-BA1 (Ex [ic] na IIC Gc) Entity Parameters: Uo = 26.4V, Io = 14mA, Co = 0.11μF, Lo = 75mH LS DI 24 VDC Isolated CHARM, model KL3005X1-LS1 (Ex na IIC Gc) LS 24 VDC Power CHARM, model KL3007X1-LS1 (Ex na IIC Gc) LS AI 4-20 ma Hart CHARM, model KL3021X1-LS1 (Ex [ic] na IIC Gc) Entity Parameters: Uo = 26.4V, Io = 30mA, Co = 0.03μF, Lo = 8mH Analog In, 4-20mA, HART, model KL3021X1-BA1 (Ex [ic] na IIC Gc), Entity Parameters: Uo = 26.4V, Io = 30mA, Co = 0.03μF, Lo = 8mH LS AI 0-10 VDC Isolated CHARM, model KL3023X1-LS1 (Ex [ic] na IIC Gc) Entity Parameters: Uo = 5.5V, Io = 3.18mA, Co = 3.2μF, Lo = 0.999mH Analog In, 0-10Volt, Isolated, model KL3023X1-BA1 (Ex [ic] na IIC Gc), Entity Parameters: Po = 18mW, Uo = 5.5V, Io = 3.18mA, Co = 3.2μF, Lo = 0.999mH LS RTD / Resistance Input Charm, model KL3031X1-LS1 (Ex [ic] na IIC Gc) Entity Parameters: Uo = 5.5V, Io = 3.18mA, Co = 3.2μF, Lo = 0.999mH RTD Input, model KL3031X1-BA1 (Ex [ic] na IIC Gc) Entity Parameters: Uo = 5.5V, Io = 3.18mA, Co = 3.2μF, Lo = 0.999mH Date: 04 August 2016 Page 2 of 6

3 LS Thermocouple/mV Charm, model KL3032X1-LS1 (Ex [ic] na IIC Gc) Entity Parameters: Uo = 5.5V, Io = 3.18mA, Co = 2.1μF, Lo = 0.999H Thermocouple Input, model KL3032X1-BA1 (Ex [ic] na IIC Gc) Entity Parameters: Uo = 5.5V, Io = 3.18mA, Co = 2.1μF, Lo = 0.999H LS DO 24 VDC DTA Charm, model KL3302X1-BA1 (Ex na IIC Gc) LS DO 24 VDC Redundant DTA Charm, model KL3302X1-BB1 (Ex na IIC Gc) LS DO 24 VDC ETA Charm, model KL3302X1-BC1 (Ex na IIC Gc) LS DO 24 VDC Redundant ETA Charm, model KL3302X1-BD1(Ex na IIC Gc) LS DVC Hart DTA Charm, model KL3322X1-BA1 (Ex [ic] na IIC Gc) Entity Parameters: Uo = 26.4V, Io = 30mA, Co = 0.05μF, Lo = 0.35mH LS DVC Hart Redundant DTA Charm, model KL3322X1-BB1 (Ex [ic] na IIC Gc) Entity Parameters: Uo = 26.4V, Io = 60mA, Co = 0.05μF, Lo = 0.3mH SZ Controller carrier model KL4001X1-BA1 (Ex na IIC Gc) Dual Universal Safety Carrier model KL4001X1-BB1 (Ex na IIC Gc) Dual Universal Carrier model KL4104X1-BA1 (Ex na IIC Gc) Standard Terminal Block; Screw Terminals for CHARMS, model KL4502X1-BA1 (Ex na ic IIC Gc) Terminal Block, Thermocouple/mV, model KL4502X1-NA1 (Ex na ic IIC Gc) 3 Wire Fused CHARM Terminal; Screw Terminals, model KL4502X1-PA1 (Ex na IIC Gc) Redundant LS DO CHARM Terminal, model KL4505X1-BA1 (Ex na ic IIC Gc) Redundant LS DVC CHARM Terminal, model KL4505X1-CA1 (Ex na ic IIC Gc) Relay ETA LS DO Charm Terminal, model KL4505X1-DA1 (Ex na nc llc) Relay DTA LS DO Charm Terminal, model KL4505X1-EA1 (Ex na nc IIC Gc) LS DVC Charm Terminal Final Assy, model KL4505X1-FA1 (Ex na ic IIC Gc) Relay DTA IP LS DO CHARM Terminal, model KL4505X1-GA1 (Ex na nc IIC Gc) Emerson DeltaV Hardware components listed below certified under IECEx NEM U: Charm I/O Carrier model KL4101X1-BA1 (Ex na IIC Gc) CHARM I/O Card (CIOC) model KL2101X1-BA1 (Ex na IIC Gc) Charm I/O Port Copper model KL1601X1-BA1 (Ex na IIC Gc) Charm Baseplate model KL4201X1-BA1 (Ex na IIC Gc) Charm Address Terminal model KL4502X1-DA1 (Ex na IIC Gc) Charm Baseplate Extender with connector, top model KL4503X1-BA1 (Ex na IIC Gc) Charm Baseplate Extender with connector, bottom model KL4503X1-CA1 (Ex na IIC Gc) Charm Column Terminator model KL4502X1-EA1 (Ex na IIC Gc) Wireless I/O Card (WIOC) model KL2102-BA1 (Ex na IIC Gc) CHARM BASEPLATE TERMINATOR TOP model KL4502X1-FA1 (Ex na IIC T4 Gc) 2-Wide Carrier for Wireless I/O Card; Screw Terminals model KL4102X1-BA1(En na IIC T4 Gc) CHARM Terminal Block with Integral Relay model KL4502X1-MA1 (En nc IIC T4 Gc) Discrete In, 24Vdc Isolated charm model KL3005X1-BA1(En na IIC T4 Gc) Discrete Out, +24VDC High Side charm, model KL3002X1-BA1 (Ex na IIC T4 Gc) Discrete Out, +24VDC Isolated DC, model KL3004X1-BA (Ex na IIC T4 Gc) Injected-Power Terminal Block with Fuse; Screw Terminals; for CHARMs, model KL4502X1-LA1 (Ex na IIC T4 Gc) Date: 04 August 2016 Page 3 of 6

4 Emerson DeltaV Hardware components listed below certified under IECEx FMG X IS-CHARM Baseplate model KL4210X1-BA1 (Ex na [ia Ga] IIC Gc) IS-CHARM Terminal Base model KL4510X1-DA1 (Ex na [ia Ga] IIC Gc) IS-CHARM Address Terminal model KL4510X1-EA1 (Ex na [ia Ga] IIC Gc) Emerson DeltaV Hardware component listed below certified under IECEx FMG U Digital Input CHARM module LS IS DI NAMUR model KL3103X1-LS D1(Ex na [ia Ga] IIC Gc) Entity Parameters: Uo = V, Io = 13 ma, Po = mw For [Ex ia] For [Ex ic] Co: 1.59 µf Co: 9.6 µf Lo: 210 mh Lo: 473 mh I.S. AI 4-20 ma HART CHARM, Analog In, model KL3101X1-BA1 (Ex na [ia Ga] IIC Gc) LS I.S. CHARM Al Hart, model KL3101X1-LS1 (Ex na [ia Ga] IIC Gc) Linear Outputs (intrinsically safe): Connections for two-wire transmitter Terminal 3 and 4 IS-CHARM Terminal Base: Entity Parameters: Uo = 27.3V, Io = 93mA, Po = 635mW, Ci = negligible, Li = negligible [Ex ia], [Ex ib]: IIC: Co = 88nF, Lo = 4.11mH IIC: Co = 297nF, Lo = 9.25mH Connection for four-wire transmitter Terminal 4 and 2 IS-CHARM Terminal Base: Entity Parameters: Uo = 27.3V, Io = Negligible, Po = Negligible, Ci = negligible, Li = negligible, Ui = 28V, Ii = 110mA, Pi = 2121mW I.S. CHARM, Analog Out, model KL3102X1-BA1(Ex na [ia Ga] IIC Gc) Linear Outputs (intrinsically safe): Terminal 3 and 4 IS-CHARM Terminal Base: Entity Parameters: Uo = 27V, Io = 93mA, Po = 628mW, Ci = negligible, Li = negligible IIC: Co = 90nF, Lo = 4.11mH IIC: Co = 309nF, Lo = 9.25mH I.S. CHARM, Discrete In, KL3103X1-BA1 (Ex na [ia Ga] IIC Gc) Linear Outputs (intrinsically safe): Terminal 3 and 4 IS-CHARM Terminal Base: Entity Parameters: Uo = 11.55V, Io = 13mA, Po = 37.54mW, Ci = negligible, Li = negligible IIC: Co = 1.59μF, Lo = 210mH IIC: Co = 9.6μF, Lo = 473mH I.S. CHARM, Discrete Out 45mA, model KL3104X1-BA1 (Ex na [ia Ga] IIC Gc) Linear Outputs (intrinsically safe): Terminal 3 and 4 IS-CHARM Terminal Base: Entity Parameters: Uo = 27.54V, Io = 110mA, Po = 760mW, Ci = negligible, Li = negligible IIC: Co = 86nF, Lo = 2.94mH IIC: Co = 285nF, Lo = 6.61mH Date: 04 August 2016 Page 4 of 6

5 IS Charm Thermocouple /mv, model KL3105X1-BA1 (Ex na [ia Ga] IIC Gc) Linear Outputs (intrinsically safe): Terminal 3 and 4 TC Terminal Base: Entity Parameters: Uo = 6.51V, Io = 50.33mA, Po = 82.00mW, Ci = negligible, Li = negligible IIC: Co = 22μF, Lo = 14.03mH IIC: Co = 285μF, Lo = 31.58mH IS Charm ThermRTD / Resistance Input, model KL3106X1-BA1 (Ex na [ia Ga] IIC Gc) Linear Outputs (intrinsically safe): Terminal 1 to 4 IS-CHARM Terminal Base: Entity Parameters: Uo = 6.51V, Io = 43.50mA, Po = 71.00mW, Ci = negligible, Li = negligible IIC: Co = 22μF, Lo = 18.79mH IIC: Co = 285μF, Lo = 42.27mH LS IS Charm RTD / Resistance Input, model KL3106X1-LS1 (Ex na [ia Ga] IIC Gc) Linear Outputs (intrinsically safe): Terminal 1 to 4 IS-CHARM Terminal Base: Entity Parameters: Uo = 6.51V, Io = 43.50mA, Po = 71.00mW, Ci = negligible, Li = negligible IIC: Co = 22μF, Lo = 18.79mH IIC: Co = 285μF, Lo = 42.27mH Emerson DeltaV Hardware components listed below certified under IECEx FMG U: Analog Out, 4-20mA, HART, model KL3022X1-BA1 (Ex na [ic] IIC Gc) Entity Parameters: Uo = 26.4V, Io = 26mA, Po = 686.4mW, Co = 0.1μF, Lo = 0.51mH Discrete Out 100mA CHARM, model KL3006X1-BA1 (Ex na [ic] IIC Gc) Entity Parameters: Uo = 26.4V, Io = 112mA, Po = 2957mW, Co = 0.105μF, Lo = 0.15mH Emerson DeltaV Hardware components listed below certified under IECEx FMG U: 24 VDC POWER CHARM, model KL3007X1-BA1 (Ex na IIC Gc) Emerson DeltaV Hardware components listed below certified under IECEx FMG X: IS-CHARM TC Terminal Base, model KL4510X1-HA1 ((Ex na [ia] IIC Gc) Emerson DeltaV Hardware components listed below certified under ECEx FMG U: Redundant Wireless I/O Card (WIOC) Term Block, model KL4302X1-CA2 (Ex na [ic] IIC Gc) Entity Parameters: Uo = 26.4V, Io = 34mA, Po = 898mW, Co = 0.175uF, Lo = 0.2mH Date: 04 August 2016 Page 5 of 6

6 Conditions Of Manufacture 1. The products covered by this certificate incorporate previously certified devices, it is therefore the responsibility of the manufacturer to continually monitor the status of the certification associated with these devices, and the manufacturer shall inform Sira of any modifications of the devices that may impinge upon the explosion safety design of their products. 2. In accordance with EN/IEC :2010 clause 6.5, each manufactured sample of the equipment shall be subjected to an electric strength test for 60 seconds, between Inputs and earth, using a test voltage of 1500Vac for 240Vac models, and 500Vac for samples supplied with voltage not exceeding 90V peak. Alternatively, a DC test voltage of 140% of the specified AC test voltage. There shall be no flashover or breakdown. Date: 04 August 2016 Page 6 of 6